From: Sasha Levin <sashal@kernel.org>
To: linux-kernel@vger.kernel.org, stable@vger.kernel.org
Cc: Sasha Levin <sashal@kernel.org>,
devicetree@vger.kernel.org, Kevin Hilman <khilman@baylibre.com>,
Christian Hewitt <christianshewitt@gmail.com>,
linux-amlogic@lists.infradead.org,
linux-arm-kernel@lists.infradead.org
Subject: [PATCH AUTOSEL 5.8 50/72] arm64: dts: meson: fix mmc0 tuning error on Khadas VIM3
Date: Sat, 8 Aug 2020 19:35:19 -0400 [thread overview]
Message-ID: <20200808233542.3617339-50-sashal@kernel.org> (raw)
In-Reply-To: <20200808233542.3617339-1-sashal@kernel.org>
From: Christian Hewitt <christianshewitt@gmail.com>
[ Upstream commit f1bb924e8f5b50752a80fa5b48c43003680a7b64 ]
Similar to other G12B devices using the W400 dtsi, I see reports of mmc0
tuning errors on VIM3 after a few hours uptime:
[12483.917391] mmc0: tuning execution failed: -5
[30535.551221] mmc0: tuning execution failed: -5
[35359.953671] mmc0: tuning execution failed: -5
[35561.875332] mmc0: tuning execution failed: -5
[61733.348709] mmc0: tuning execution failed: -5
I do not see the same on VIM3L, so remove sd-uhs-sdr50 from the common dtsi
to silence the error, then (re)add it to the VIM3L dts.
Fixes: 4f26cc1c96c9 ("arm64: dts: khadas-vim3: move common nodes into meson-khadas-vim3.dtsi")
Fixes: 700ab8d83927 ("arm64: dts: khadas-vim3: add support for the SM1 based VIM3L")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200721015950.11816-1-christianshewitt@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi | 1 -
arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts | 4 ++++
2 files changed, 4 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi b/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi
index 1ef1e3672b967..ff5ba85b7562e 100644
--- a/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi
@@ -270,7 +270,6 @@ &sd_emmc_a {
bus-width = <4>;
cap-sd-highspeed;
- sd-uhs-sdr50;
max-frequency = <100000000>;
non-removable;
diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts
index dbbf29a0dbf6d..026b21708b078 100644
--- a/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts
@@ -88,6 +88,10 @@ &pcie {
status = "okay";
};
+&sd_emmc_a {
+ sd-uhs-sdr50;
+};
+
&usb {
phys = <&usb2_phy0>, <&usb2_phy1>;
phy-names = "usb2-phy0", "usb2-phy1";
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2020-08-08 23:43 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-08-08 23:34 [PATCH AUTOSEL 5.8 01/72] ARM: dts: stm32: fix uart nodes ordering in stm32mp15-pinctrl Sasha Levin
2020-08-08 23:34 ` [PATCH AUTOSEL 5.8 02/72] ARM: dts: stm32: fix uart7_pins_a comments " Sasha Levin
2020-08-08 23:34 ` [PATCH AUTOSEL 5.8 10/72] arm64: dts: rockchip: fix rk3368-lion gmac reset gpio Sasha Levin
2020-08-08 23:34 ` [PATCH AUTOSEL 5.8 11/72] arm64: dts: rockchip: fix rk3399-puma vcc5v0-host gpio Sasha Levin
2020-08-08 23:34 ` [PATCH AUTOSEL 5.8 12/72] arm64: dts: rockchip: fix rk3399-puma gmac reset gpio Sasha Levin
2020-08-08 23:34 ` [PATCH AUTOSEL 5.8 20/72] ARM: exynos: MCPM: Restore big.LITTLE cpuidle support Sasha Levin
2020-08-08 23:34 ` [PATCH AUTOSEL 5.8 22/72] firmware: arm_scmi: Fix SCMI genpd domain probing Sasha Levin
2020-08-08 23:34 ` [PATCH AUTOSEL 5.8 23/72] arm64: dts: sun50i-pinephone: dldo4 must not be >= 1.8V Sasha Levin
2020-08-08 23:34 ` [PATCH AUTOSEL 5.8 24/72] arm64: dts: exynos: Fix silent hang after boot on Espresso Sasha Levin
2020-08-08 23:34 ` [PATCH AUTOSEL 5.8 27/72] clk: scmi: Fix min and max rate when registering clocks with discrete rates Sasha Levin
2020-08-08 23:35 ` [PATCH AUTOSEL 5.8 35/72] ARM: at91: pm: add missing put_device() call in at91_pm_sram_init() Sasha Levin
2020-08-08 23:35 ` [PATCH AUTOSEL 5.8 36/72] ARM: dts: exynos: Disable frequency scaling for FSYS bus on Odroid XU3 family Sasha Levin
2020-08-08 23:35 ` [PATCH AUTOSEL 5.8 38/72] ARM: dts: at91: sama5d3_xplained: change phy-mode Sasha Levin
2020-08-08 23:35 ` [PATCH AUTOSEL 5.8 39/72] ARM: dts: sunxi: bananapi-m2-plus-v1.2: Add regulator supply to all CPU cores Sasha Levin
2020-08-08 23:35 ` [PATCH AUTOSEL 5.8 40/72] ARM: dts: sunxi: bananapi-m2-plus-v1.2: Fix CPU supply voltages Sasha Levin
2020-08-08 23:35 ` [PATCH AUTOSEL 5.8 41/72] ARM: dts: stm32: Fix spi4 pins in stm32mp15-pinctrl Sasha Levin
2020-08-08 23:35 ` [PATCH AUTOSEL 5.8 49/72] arm64: dts: meson: misc fixups for w400 dtsi Sasha Levin
2020-08-08 23:35 ` Sasha Levin [this message]
2020-08-08 23:35 ` [PATCH AUTOSEL 5.8 52/72] spi: rockchip: Fix error in SPI slave pio read Sasha Levin
2020-08-08 23:35 ` [PATCH AUTOSEL 5.8 53/72] ARM: socfpga: PM: add missing put_device() call in socfpga_setup_ocram_self_refresh() Sasha Levin
2020-08-08 23:35 ` [PATCH AUTOSEL 5.8 56/72] irqchip/ti-sci-inta: Fix return value about devm_ioremap_resource() Sasha Levin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200808233542.3617339-50-sashal@kernel.org \
--to=sashal@kernel.org \
--cc=christianshewitt@gmail.com \
--cc=devicetree@vger.kernel.org \
--cc=khilman@baylibre.com \
--cc=linux-amlogic@lists.infradead.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=stable@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).