From: Sasha Levin <sashal@kernel.org>
To: linux-kernel@vger.kernel.org, stable@vger.kernel.org
Cc: Sasha Levin <sashal@kernel.org>,
devicetree@vger.kernel.org, linux-samsung-soc@vger.kernel.org,
Krzysztof Kozlowski <krzk@kernel.org>,
Alim Akhtar <alim.akhtar@samsung.com>,
linux-arm-kernel@lists.infradead.org
Subject: [PATCH AUTOSEL 5.7 21/58] arm64: dts: exynos: Fix silent hang after boot on Espresso
Date: Sat, 8 Aug 2020 19:36:47 -0400 [thread overview]
Message-ID: <20200808233724.3618168-21-sashal@kernel.org> (raw)
In-Reply-To: <20200808233724.3618168-1-sashal@kernel.org>
From: Alim Akhtar <alim.akhtar@samsung.com>
[ Upstream commit b072714bfc0e42c984b8fd6e069f3ca17de8137a ]
Once regulators are disabled after kernel boot, on Espresso board silent
hang observed because of LDO7 being disabled. LDO7 actually provide
power to CPU cores and non-cpu blocks circuitries. Keep this regulator
always-on to fix this hang.
Fixes: 9589f7721e16 ("arm64: dts: Add S2MPS15 PMIC node on exynos7-espresso")
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
arch/arm64/boot/dts/exynos/exynos7-espresso.dts | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm64/boot/dts/exynos/exynos7-espresso.dts b/arch/arm64/boot/dts/exynos/exynos7-espresso.dts
index 7af288fa9475f..a9412805c1d6a 100644
--- a/arch/arm64/boot/dts/exynos/exynos7-espresso.dts
+++ b/arch/arm64/boot/dts/exynos/exynos7-espresso.dts
@@ -157,6 +157,7 @@ ldo7_reg: LDO7 {
regulator-min-microvolt = <700000>;
regulator-max-microvolt = <1150000>;
regulator-enable-ramp-delay = <125>;
+ regulator-always-on;
};
ldo8_reg: LDO8 {
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2020-08-08 23:47 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-08-08 23:36 [PATCH AUTOSEL 5.7 01/58] ARM: dts: stm32: fix uart7_pins_a comments in stm32mp15-pinctrl Sasha Levin
2020-08-08 23:36 ` [PATCH AUTOSEL 5.7 08/58] arm64: dts: rockchip: fix rk3368-lion gmac reset gpio Sasha Levin
2020-08-08 23:36 ` [PATCH AUTOSEL 5.7 09/58] arm64: dts: rockchip: fix rk3399-puma vcc5v0-host gpio Sasha Levin
2020-08-08 23:36 ` [PATCH AUTOSEL 5.7 10/58] arm64: dts: rockchip: fix rk3399-puma gmac reset gpio Sasha Levin
2020-08-08 23:36 ` [PATCH AUTOSEL 5.7 17/58] ARM: exynos: MCPM: Restore big.LITTLE cpuidle support Sasha Levin
2020-08-08 23:36 ` [PATCH AUTOSEL 5.7 19/58] firmware: arm_scmi: Fix SCMI genpd domain probing Sasha Levin
2020-08-08 23:36 ` [PATCH AUTOSEL 5.7 20/58] arm64: dts: sun50i-pinephone: dldo4 must not be >= 1.8V Sasha Levin
2020-08-08 23:36 ` Sasha Levin [this message]
2020-08-08 23:36 ` [PATCH AUTOSEL 5.7 24/58] clk: scmi: Fix min and max rate when registering clocks with discrete rates Sasha Levin
2020-08-08 23:36 ` [PATCH AUTOSEL 5.7 32/58] ARM: at91: pm: add missing put_device() call in at91_pm_sram_init() Sasha Levin
2020-08-08 23:36 ` [PATCH AUTOSEL 5.7 33/58] ARM: dts: exynos: Disable frequency scaling for FSYS bus on Odroid XU3 family Sasha Levin
2020-08-08 23:37 ` [PATCH AUTOSEL 5.7 35/58] ARM: dts: sunxi: bananapi-m2-plus-v1.2: Add regulator supply to all CPU cores Sasha Levin
2020-08-08 23:37 ` [PATCH AUTOSEL 5.7 36/58] ARM: dts: sunxi: bananapi-m2-plus-v1.2: Fix CPU supply voltages Sasha Levin
2020-08-08 23:37 ` [PATCH AUTOSEL 5.7 42/58] arm64: dts: meson: fix mmc0 tuning error on Khadas VIM3 Sasha Levin
2020-08-08 23:37 ` [PATCH AUTOSEL 5.7 44/58] spi: rockchip: Fix error in SPI slave pio read Sasha Levin
2020-08-08 23:37 ` [PATCH AUTOSEL 5.7 45/58] ARM: socfpga: PM: add missing put_device() call in socfpga_setup_ocram_self_refresh() Sasha Levin
2020-08-08 23:37 ` [PATCH AUTOSEL 5.7 48/58] irqchip/ti-sci-inta: Fix return value about devm_ioremap_resource() Sasha Levin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200808233724.3618168-21-sashal@kernel.org \
--to=sashal@kernel.org \
--cc=alim.akhtar@samsung.com \
--cc=devicetree@vger.kernel.org \
--cc=krzk@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-samsung-soc@vger.kernel.org \
--cc=stable@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).