linux-arm-kernel.lists.infradead.org archive mirror
 help / color / mirror / Atom feed
From: Viresh Kumar <viresh.kumar@linaro.org>
To: Nicola Mazzucato <nicola.mazzucato@arm.com>
Cc: devicetree@vger.kernel.org, linux-pm@vger.kernel.org,
	vireshk@kernel.org, daniel.lezcano@linaro.org, rjw@rjwysocki.net,
	linux-kernel@vger.kernel.org, robh+dt@kernel.org,
	sudeep.holla@arm.com, chris.redpath@arm.com,
	Ionela Voinescu <ionela.voinescu@arm.com>,
	morten.rasmussen@arm.com, linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH v2 2/2] [RFC] CPUFreq: Add support for cpu-perf-dependencies
Date: Fri, 9 Oct 2020 11:09:21 +0530	[thread overview]
Message-ID: <20201009053921.pkq4pcyrv4r7ylzu@vireshk-i7> (raw)
In-Reply-To: <56846759-e3a6-9471-827d-27af0c3d410d@arm.com>

On 08-10-20, 17:00, Nicola Mazzucato wrote:
> On 10/8/20 4:03 PM, Ionela Voinescu wrote:
> > Hi Viresh,
> > 
> > On Thursday 08 Oct 2020 at 16:32:41 (+0530), Viresh Kumar wrote:
> >> On 07-10-20, 13:58, Nicola Mazzucato wrote:
> >>> Hi Viresh,
> >>>
> >>> performance controls is what is exposed by the firmware through a protocol that
> >>> is not capable of describing hardware (say SCMI). For example, the firmware can
> >>> tell that the platform has N controls, but it can't say to which hardware they
> >>> are "wired" to. This is done in dt, where, for example, we map these controls
> >>> to cpus, gpus, etc.
> >>>
> >>> Let's focus on cpus.
> >>>
> >>> Normally we would have N of performance controls (what comes from f/w)
> >>> that that correspond to hardware clock/dvfs domains.
> >>>
> >>> However, some firmware implementations might benefit from having finer
> >>> grained information about the performance requirements (e.g.
> >>> per-CPU) and therefore choose to present M performance controls to the
> >>> OS. DT would be adjusted accordingly to "wire" these controls to cpus
> >>> or set of cpus.
> >>> In this scenario, the f/w will make aggregation decisions based on the
> >>> requests it receives on these M controls.
> >>>
> >>> Here we would have M cpufreq policies which do not necessarily reflect the
> >>> underlying clock domains, thus some s/w components will underperform
> >>> (EAS and thermal, for example).
> >>>
> >>> A real example would be a platform in which the firmware describes the system
> >>> having M per-cpu control, and the cpufreq subsystem will have M policies while
> >>> in fact these cpus are "performance-dependent" each other (e.g. are in the same
> >>> clock domain).
> >>
> >> If the CPUs are in the same clock domain, they must be part of the
> >> same cpufreq policy.
> > 
> > But cpufreq does not currently support HW_ALL (I'm using the ACPI
> > coordination type to describe the generic scenario of using hardware
> > aggregation and coordination when establishing the clock rate of CPUs).
> > 
> > Adding support for HW_ALL* will involve either bypassing some
> > assumptions around cpufreq policies or making core cpufreq changes.
> > 
> > In the way I see it, support for HW_ALL involves either:
> > 
> >  - (a) Creating per-cpu policies in order to allow each of the CPUs to
> >    send their own frequency request to the hardware which will do
> >    aggregation and clock rate decision at the level of the clock
> >    domain. The PSD domains (ACPI) and the new DT binding will tell
> >    which CPUs are actually in the same clock domain for whomever is
> >    interested, despite those CPUs not being in the same policy.
> >    This requires the extra mask that Nicola introduced.
> > 
> >  - (b) Making deep changes to cpufreq (core/governors/drivers) to allow:
> >    - Governors to stop aggregating (usually max) the information
> >      for each of the CPUs in the policy and convey to the core
> >      information for each CPU.
> >    - Cpufreq core to be able to receive and pass this information
> >      down to the drivers.
> >    - Drivers to be able to have some per cpu structures to hold
> >      frequency control (let's say SCP fast channel addresses) for
> >      each of the CPUs in the policy. Or have these structures in the
> >      cpufreq core/policy, to avoid code duplication in drivers.
> > 
> > Therefore (a) is the least invasive but we'll be bypassing the rule
> > above. But to make that rule stick we'll have to make invasive cpufreq
> > changes (b).
> 
> Regarding the 'rule' above of one cpufreq policy per clock domain, I would like
> to share my understanding on it. Perhaps it's a good opportunity to shed some light.
> 
> Looking back in the history of CPUFreq, related_cpus was originally designed
> to hold the map of cpus within the same clock. Later on, the meaning of this
> cpumask changed [1].
> This led to the introduction of a new cpumask 'freqdomain_cpus'
> within acpi-cpufreq to keep the knowledge of hardware clock domains for
> sysfs consumers since related_cpus was not suitable anymore for this.
> Further on, this cpumask was assigned to online+offline cpus within the same clk
> domain when sw coordination is in use [2].
> 
> My interpretation is that there is no guarantee that related_cpus holds the
> 'real' hardware clock implementation. As a consequence, it is not true anymore
> that cpus that are in the same clock domain will be part of the same
> policy.
> 
> This guided me to think it would be better to have a cpumask which always holds
> the real hw clock domains in the policy.
> 
> > 
> > This is my current understanding and I'm leaning towards (a). What do
> > you think?
> > 
> > *in not so many words, this is what these patches are trying to propose,
> > while also making sure it's supported for both ACPI and DT.
> > 
> > BTW, thank you for your effort in making sense of this!
> > 
> > Regards,
> > Ionela.
> > 
> 
> This could be a platform where per-cpu and perf-dependencies will be used:
> 
> CPU:              0    1    2    3    4    5    6    7
> Type:             A    A    A    A    B    B    B    B
> Cluster:         [                                    ]
> perf-controls:   [  ] [  ] [  ] [ ]  [ ]  [ ]  [ ]  [ ]
> perf-dependency: [                ]  [                ]
> HW clock:        [                ]  [                ]
> 
> The firmware will present 8 controls to the OS and each control is mapped to a
> cpu device via the standard dt. This is done so we can achieve hw coordination.
> What is required in these systems is to present to OS the information of which
> cpus belong to which clock domain. In other words, when hw coordinates we don't
> have any way at present in dt to understand how these cpus are dependent
> each other, from performance perspective (as opposed to ACPI where we have
> _PSD). Hence my proposal for the new cpu-perf-dependencies.
> This is regardless whether we decide to go for either a policy per-cpu or a
> policy per-domain.
> 
> Hope it helps.

Oh yes, I get it now. Finally. Thanks for helping me out :)

So if I can say all this stuff in simple terms, this is what it will
be like:

- We don't want software aggregation of frequencies and so we need to
  have per-cpu policies even when they share their clock lines.

- But we still need a way for other frameworks to know which CPUs
  share the clock lines (that's what the perf-dependency is all about,
  right ?).

- We can't get it from SCMI, but need a DT based solution.

- Currently for the cpufreq-case we relied for this on the way OPP
  tables for the CPUs were described. i.e. the opp-table is marked as
  "shared" and multiple CPUs point to it.

- I wonder if we can keep using that instead of creating new bindings
  for exact same stuff ? Though the difference here would be that the
  OPP may not have any other entries.

-- 
viresh

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

  reply	other threads:[~2020-10-09  5:41 UTC|newest]

Thread overview: 44+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-09-24  9:53 [PATCH v2 0/2] CPUFreq: Add support for cpu performance dependencies Nicola Mazzucato
2020-09-24  9:53 ` [PATCH v2 1/2] dt-bindings: arm: Add devicetree binding for cpu-performance-dependencies Nicola Mazzucato
2020-10-08 13:42   ` Ionela Voinescu
2020-09-24  9:53 ` [PATCH v2 2/2] [RFC] CPUFreq: Add support for cpu-perf-dependencies Nicola Mazzucato
2020-10-06  7:19   ` Viresh Kumar
2020-10-07 12:58     ` Nicola Mazzucato
2020-10-08 11:02       ` Viresh Kumar
2020-10-08 15:03         ` Ionela Voinescu
2020-10-08 15:57           ` Rafael J. Wysocki
2020-10-08 17:08             ` Ionela Voinescu
2020-10-12 16:06             ` Sudeep Holla
2020-10-08 16:00           ` Nicola Mazzucato
2020-10-09  5:39             ` Viresh Kumar [this message]
2020-10-09 11:10               ` Nicola Mazzucato
2020-10-09 11:17                 ` Viresh Kumar
2020-10-09 14:01                 ` Rob Herring
2020-10-09 15:28                   ` Nicola Mazzucato
2020-10-12  4:19                     ` Viresh Kumar
2020-10-12 10:22                   ` Lukasz Luba
2020-10-12 10:50                     ` Rafael J. Wysocki
2020-10-12 11:05                       ` Lukasz Luba
2020-10-12 10:59                     ` Ionela Voinescu
2020-10-12 13:48                       ` Lukasz Luba
2020-10-12 16:30                         ` Ionela Voinescu
2020-10-12 18:19                           ` Lukasz Luba
2020-10-12 22:01                             ` Ionela Voinescu
2020-10-13 11:53                               ` Rafael J. Wysocki
2020-10-13 12:39                                 ` Ionela Voinescu
2020-10-15 15:56                                   ` Rafael J. Wysocki
2020-10-15 18:38                                     ` Ionela Voinescu
2020-10-12 13:59                     ` Rob Herring
2020-10-12 16:02                     ` Sudeep Holla
2020-10-12 15:54                   ` Sudeep Holla
2020-10-12 15:49               ` Sudeep Holla
2020-10-12 16:52                 ` Ionela Voinescu
2020-10-12 17:18                   ` Lukasz Luba
2020-10-14  4:25                     ` Viresh Kumar
2020-10-14  9:11                       ` Lukasz Luba
2020-10-19  8:50                       ` Nicola Mazzucato
2020-10-19  9:46                         ` Viresh Kumar
2020-10-19 13:36                           ` Nicola Mazzucato
2020-10-20 10:48                             ` Viresh Kumar
2020-10-13 13:53               ` Lukasz Luba
2020-10-14  4:20                 ` Viresh Kumar

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20201009053921.pkq4pcyrv4r7ylzu@vireshk-i7 \
    --to=viresh.kumar@linaro.org \
    --cc=chris.redpath@arm.com \
    --cc=daniel.lezcano@linaro.org \
    --cc=devicetree@vger.kernel.org \
    --cc=ionela.voinescu@arm.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-pm@vger.kernel.org \
    --cc=morten.rasmussen@arm.com \
    --cc=nicola.mazzucato@arm.com \
    --cc=rjw@rjwysocki.net \
    --cc=robh+dt@kernel.org \
    --cc=sudeep.holla@arm.com \
    --cc=vireshk@kernel.org \
    --subject='Re: [PATCH v2 2/2] [RFC] CPUFreq: Add support for cpu-perf-dependencies' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).