From: Marek Vasut <marex@denx.de>
To: dri-devel@lists.freedesktop.org
Cc: Marek Vasut <marex@denx.de>,
Benjamin Gaignard <benjamin.gaignard@st.com>,
Antonio Borneo <antonio.borneo@st.com>,
Vincent Abriou <vincent.abriou@st.com>,
Philippe Cornu <philippe.cornu@st.com>,
Yannick Fertre <yannick.fertre@st.com>,
Maxime Coquelin <mcoquelin.stm32@gmail.com>,
Sam Ravnborg <sam@ravnborg.org>,
linux-stm32@st-md-mailman.stormreply.com,
linux-arm-kernel@lists.infradead.org,
Alexandre Torgue <alexandre.torgue@st.com>
Subject: [PATCH V4] drm/stm: Fix bus_flags handling
Date: Wed, 27 Jan 2021 12:07:56 +0100 [thread overview]
Message-ID: <20210127110756.125570-1-marex@denx.de> (raw)
The drm_display_mode_to_videomode() does not populate DISPLAY_FLAGS_DE_LOW
or DISPLAY_FLAGS_PIXDATA_NEGEDGE flags in struct videomode. Therefore, no
matter what polarity the next bridge or display might require, these flags
are never set, and thus the LTDC GCR_DEPOL and GCR_PCPOL bits are never set,
and the LTDC behaves as if both DISPLAY_FLAGS_PIXDATA_POSEDGE and
DISPLAY_FLAGS_DE_HIGH were always set.
The fix for this problem is taken almost verbatim from MXSFB driver. In
case there is a bridge attached to the LTDC, the bridge might have extra
polarity requirements, so extract bus_flags from the bridge and use them
for LTDC configuration. Otherwise, extract bus_flags from the connector,
which is the display.
Fixes: b759012c5fa7 ("drm/stm: Add STM32 LTDC driver")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Antonio Borneo <antonio.borneo@st.com>
Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Philippe Cornu <philippe.cornu@st.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Yannick Fertre <yannick.fertre@st.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-stm32@st-md-mailman.stormreply.com
To: dri-devel@lists.freedesktop.org
---
V2: Check if ldev->bridge->timings is non-NULL before accessing it
V3: get bus_flags from connector (from Yannick)
- Display controller could support several connectors (not connected at
the same time). ie: stm32mp15c-DK2 board have 2 connectors (HDMI + DSI).
Driver check which connector is connected to get the bus flag.
V4: get bridge from encoder (from Yannick)
---
drivers/gpu/drm/stm/ltdc.c | 33 +++++++++++++++++++++++++++++++--
1 file changed, 31 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/stm/ltdc.c b/drivers/gpu/drm/stm/ltdc.c
index 6e28e6b60e72..acc9f6694eb6 100644
--- a/drivers/gpu/drm/stm/ltdc.c
+++ b/drivers/gpu/drm/stm/ltdc.c
@@ -544,13 +544,42 @@ static void ltdc_crtc_mode_set_nofb(struct drm_crtc *crtc)
{
struct ltdc_device *ldev = crtc_to_ltdc(crtc);
struct drm_device *ddev = crtc->dev;
+ struct drm_connector_list_iter iter;
+ struct drm_connector *connector = NULL;
+ struct drm_encoder *encoder = NULL;
+ struct drm_bridge *bridge = NULL;
struct drm_display_mode *mode = &crtc->state->adjusted_mode;
struct videomode vm;
u32 hsync, vsync, accum_hbp, accum_vbp, accum_act_w, accum_act_h;
u32 total_width, total_height;
+ u32 bus_flags = 0;
u32 val;
int ret;
+ /* get encoder from crtc */
+ drm_for_each_encoder(encoder, ddev)
+ if (encoder->crtc == crtc)
+ break;
+
+ if (encoder) {
+ /* get bridge from encoder */
+ list_for_each_entry(bridge, &encoder->bridge_chain, chain_node)
+ if (bridge->encoder == encoder)
+ break;
+
+ /* Get the connector from encoder */
+ drm_connector_list_iter_begin(ddev, &iter);
+ drm_for_each_connector_iter(connector, &iter)
+ if (connector->encoder == encoder)
+ break;
+ drm_connector_list_iter_end(&iter);
+ }
+
+ if (bridge && bridge->timings)
+ bus_flags = bridge->timings->input_bus_flags;
+ else if (connector)
+ bus_flags = connector->display_info.bus_flags;
+
if (!pm_runtime_active(ddev->dev)) {
ret = pm_runtime_get_sync(ddev->dev);
if (ret) {
@@ -586,10 +615,10 @@ static void ltdc_crtc_mode_set_nofb(struct drm_crtc *crtc)
if (vm.flags & DISPLAY_FLAGS_VSYNC_HIGH)
val |= GCR_VSPOL;
- if (vm.flags & DISPLAY_FLAGS_DE_LOW)
+ if (bus_flags & DRM_BUS_FLAG_DE_LOW)
val |= GCR_DEPOL;
- if (vm.flags & DISPLAY_FLAGS_PIXDATA_NEGEDGE)
+ if (bus_flags & DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE)
val |= GCR_PCPOL;
reg_update_bits(ldev->regs, LTDC_GCR,
--
2.29.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next reply other threads:[~2021-01-27 11:10 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-01-27 11:07 Marek Vasut [this message]
2021-01-28 13:55 ` [PATCH V4] drm/stm: Fix bus_flags handling yannick Fertre
2021-02-15 17:43 ` Philippe CORNU
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210127110756.125570-1-marex@denx.de \
--to=marex@denx.de \
--cc=alexandre.torgue@st.com \
--cc=antonio.borneo@st.com \
--cc=benjamin.gaignard@st.com \
--cc=dri-devel@lists.freedesktop.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-stm32@st-md-mailman.stormreply.com \
--cc=mcoquelin.stm32@gmail.com \
--cc=philippe.cornu@st.com \
--cc=sam@ravnborg.org \
--cc=vincent.abriou@st.com \
--cc=yannick.fertre@st.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).