[PATCH v5 00/20] arm64: sunxi: Initial Allwinner H616 SoC support

[PATCH v5 00/20] arm64: sunxi: Initial Allwinner H616 SoC support

[Andre Przywara]

Hi,

this is a small update from v4, fixing some DT validation issues:
dtbs_check now comes back clean for me.
Also I dropped USB support for now. It turns out that this is more messy
than we thought: it only works if all four USB controllers are enabled
(and not just some PHYs). That smells like some shared reset or clock
gate, but we haven't found the culprit yet. Also the BSP source suggests
that there is a "hardware design issue" that requires some PHY tune
register to be programmed, so we probably need more code anyway.
I also dropped the DT node for the second EMAC, as this is mostly
untested at this point.

Changelog below. Based on the (updated) sunxi/for-next branch.

I was hoping that at least the clock and AXP patches (01/20-06/20) could
make it into 5.12 still?  That would allow booting boards from SD card.
Patch 08/20 would enable Ethernet.
U-Boot support is now merged into its master tree.

Thanks!
Andre

==================
This series gathers patches to support the Allwinner H616 SoC. This is
a rather uninspired SoC (Quad-A53 with the usual peripherals), but
allows for some cheap development boards and TV boxes, and supports
up to 4GB of DRAM.

Various DT binding patches are sprinkled throughout the series, to add
the new compatible names right before they are used.
Patch 2 and 3 add clock support. For the -R clock this is shared with
the H6 code, as the clocks are identical, with the H616 just having
fewer of them. The main clocks are different enough to warrant a separate
file.
Patches 5 and 6 teach the AXP MFD driver to get along without having an
interrupt, as the missing NMI pin on the H616 leads to some boards not
having the AXP IRQ line connected.
Patch 8 and 16 add some tweaks to the syscon and EMAC driver, to deal
with the second EMAC clock used for the second Ethernet controller.
This is somewhat optional for the current .dts, as this doesn't use
the second EMAC.

The remaining patches add DT bindings, which just add the new compatible
string along with an existing name as a fallback string.
Eventually we get the .dtsi for the SoC in patch 19, and the .dts for
the OrangePi Zero2 board[1] in the last patch.

We have U-Boot and Trusted-Firmware support in a working state, booting
via FEL or SD card and even TFTPing kernels work already [2][3].
The U-Boot patches are already merged into the mainline repository.

Many thanks to Jernej for his tremendous help on this, also for the
awesome input and help from the #linux-sunxi Freenode channel.

The whole series (including the other patches) can also be found here:
https://github.com/apritzel/linux/commits/h616-v5

Happy reviewing!

Cheers,
Andre

[1] https://linux-sunxi.org/Xunlong_Orange_Pi_Zero2
[2] https://github.com/jernejsk/u-boot/commits/h616-v2
[3] https://github.com/apritzel/arm-trusted-firmware/commits/h616-v1

Changelog v4 .. v5:
- Fix CCU binding to pass dtbs_check
- Add RSB compatible string to binding doc
- Rename IR pin name to pass dtbs_check
- Add EMAC compatible string to binding doc
- Drop USB PHY support and binding doc patches 
- Drop USB nodes from .dtsi and .dts
- Drop second EMAC node from .dtsi

Changelog v3 .. v4:
- Drop MMC and pinctrl matches (already in some -next trees)
- Add Maxime's Acks
- Add patch to update the AXP MFD DT bindings
- Add new patch (05/21) to fix axp20x-pek driver
- Change AXP IRQ fix to check for invalid IRQ line number
- Split joint DT bindings patch (v3 18/21) into subsystems
- move dwmac variable to keep christmas tree
- Use enums for USB PHY compatible strings in DT binding
- Enable watchdog (briefly verified to work)
- Add PHY2 to HCI1&3, this fixes USB
- limit r-ccu register frame length to not collide with NMI controller
- add interrupt-controller property to AXP DT node

Changelog v2 .. v3:
- Add Rob's Acks
- Drop redundant maxItems from pinctrl DT binding
- Rename h_i2s* to just i2s* in pinctrl names
- Use more declarative i2s0_d{in,out}{0,1} names
- Add RSB pins to pinctrl
- Include RSB clocks (sharing with newly added H6 versions)
- Fix CEC clock (add 2nd enable bit, also fix predivider flag)
- Rename PMU_UNK1 register in USB PHY
- Add USB and MUSB DT binding patches
- Add MMC/SD speed modes to .dtsi

Changelog v1 .. v2:
- pinctrl: adjust irq bank map to cover undocumented GPIO bank IRQs
- use differing h_i2s0 pin output names
- r-ccu: fix number of used clocks
- ccu: remove PLL-PERIPHy(4X)
- ccu: fix gpu1 divider range
- ccu: fix usb-phy3 parent
- ccu: add missing TV clocks
- ccu: rework to CLK_OF_DECLARE style
- ccu: enable output bit for PLL clocks
- ccu: renumber clocks
- .dtsi: drop sun50i-a64-system-control fallback
- .dtsi: drop unknown SRAM regions
- .dtsi: add more (undocumented) GPIO interrupts
- .dtsi: fix I2C3 pin names
- .dtsi: use a100-emmc fallback for MMC2
- .dtsi: add second EMAC controller
- .dtsi: use H3 MUSB controller fallback
- .dtsi: fix frame size for USB PHY PMU registers
- .dtsi: add USB0 PHY references
- .dtsi: fix IR controller clock source
- .dts: fix LED naming and swap pins
- .dts: use 5V supply parent for USB supply
- .dts: drop dummy IRQ for AXP
- .dts: enable 3V3 header pin power rail
- .dts: add SPI flash node
- .dts: make USB-C port peripheral only
- add IRQ-less AXP support
- add two patches to support more than one EMAC clock
- add patch to rework and extend USB PHY support
- add DT binding documentation patches

Andre Przywara (20):
  dt-bindings: clk: sunxi-ccu: Add compatible string for Allwinner H616
  clk: sunxi-ng: Add support for the Allwinner H616 R-CCU
  clk: sunxi-ng: Add support for the Allwinner H616 CCU
  dt-bindings: mfd: axp20x: Add AXP305 compatible (plus optional IRQ)
  Input: axp20x-pek: Bail out if AXP has no interrupt line connected
  mfd: axp20x: Allow AXP chips without interrupt lines
  dt-bindings: sram: sunxi-sram: Add H616 compatible string
  soc: sunxi: sram: Add support for more than one EMAC clock
  dt-bindings: watchdog: sun4i: Add H616 compatible string
  dt-bindings: i2c: mv64xxx: Add H616 compatible string
  dt-bindings: media: IR: Add H616 IR compatible string
  dt-bindings: rtc: sun6i: Add H616 compatible string
  dt-bindings: spi: sunxi: Add H616 compatible string
  dt-bindings: bus: rsb: Add H616 compatible string
  dt-bindings: net: sun8i-emac: Add H616 compatible string
  net: stmmac: dwmac-sun8i: Prepare for second EMAC clock register
  phy: sun4i-usb: Rework HCI PHY (aka. "pmu_unk1") handling
  arm64: dts: allwinner: Add Allwinner H616 .dtsi file
  dt-bindings: arm: sunxi: Add OrangePi Zero 2 binding
  arm64: dts: allwinner: Add OrangePi Zero 2 .dts

 .../devicetree/bindings/arm/sunxi.yaml        |    5 +
 .../bindings/bus/allwinner,sun8i-a23-rsb.yaml |    4 +-
 .../clock/allwinner,sun4i-a10-ccu.yaml        |    4 +
 .../bindings/i2c/marvell,mv64xxx-i2c.yaml     |   21 +-
 .../media/allwinner,sun4i-a10-ir.yaml         |   16 +-
 .../devicetree/bindings/mfd/axp20x.txt        |    3 +-
 .../net/allwinner,sun8i-a83t-emac.yaml        |    4 +-
 .../bindings/rtc/allwinner,sun6i-a31-rtc.yaml |    3 +
 .../bindings/spi/allwinner,sun6i-a31-spi.yaml |    1 +
 .../allwinner,sun4i-a10-system-control.yaml   |    1 +
 .../watchdog/allwinner,sun4i-a10-wdt.yaml     |   12 +-
 arch/arm64/boot/dts/allwinner/Makefile        |    1 +
 .../allwinner/sun50i-h616-orangepi-zero2.dts  |  203 +++
 .../arm64/boot/dts/allwinner/sun50i-h616.dtsi |  573 ++++++++
 drivers/clk/sunxi-ng/Kconfig                  |    7 +-
 drivers/clk/sunxi-ng/Makefile                 |    1 +
 drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c        |   48 +
 drivers/clk/sunxi-ng/ccu-sun50i-h616.c        | 1150 +++++++++++++++++
 drivers/clk/sunxi-ng/ccu-sun50i-h616.h        |   56 +
 drivers/input/misc/axp20x-pek.c               |    4 +
 drivers/mfd/axp20x.c                          |   17 +-
 .../net/ethernet/stmicro/stmmac/dwmac-sun8i.c |   12 +-
 drivers/phy/allwinner/phy-sun4i-usb.c         |   29 +-
 drivers/soc/sunxi/sunxi_sram.c                |   31 +-
 include/dt-bindings/clock/sun50i-h616-ccu.h   |  115 ++
 include/dt-bindings/reset/sun50i-h616-ccu.h   |   70 +
 26 files changed, 2323 insertions(+), 68 deletions(-)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
 create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-h616.c
 create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-h616.h
 create mode 100644 include/dt-bindings/clock/sun50i-h616-ccu.h
 create mode 100644 include/dt-bindings/reset/sun50i-h616-ccu.h

-- 
2.17.5


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 01/20] dt-bindings: clk: sunxi-ccu: Add compatible string for Allwinner H616

[Andre Przywara]

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
---
 .../devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml    | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml b/Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml
index 3b45344ed758..a27025cd3909 100644
--- a/Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml
+++ b/Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml
@@ -41,6 +41,8 @@ properties:
       - allwinner,sun50i-h5-ccu
       - allwinner,sun50i-h6-ccu
       - allwinner,sun50i-h6-r-ccu
+      - allwinner,sun50i-h616-ccu
+      - allwinner,sun50i-h616-r-ccu
       - allwinner,suniv-f1c100s-ccu
       - nextthing,gr8-ccu
 
@@ -82,6 +84,7 @@ if:
         - allwinner,sun50i-a64-r-ccu
         - allwinner,sun50i-a100-r-ccu
         - allwinner,sun50i-h6-r-ccu
+        - allwinner,sun50i-h616-r-ccu
 
 then:
   properties:
@@ -100,6 +103,7 @@ else:
         enum:
           - allwinner,sun50i-a100-ccu
           - allwinner,sun50i-h6-ccu
+          - allwinner,sun50i-h616-ccu
 
   then:
     properties:
-- 
2.17.5


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 02/20] clk: sunxi-ng: Add support for the Allwinner H616 R-CCU

[Andre Przywara]

The clocks itself are identical to the H6 R-CCU, it's just that the H616
has not all of them implemented (or connected).

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
---
 drivers/clk/sunxi-ng/Kconfig           |  2 +-
 drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c | 48 ++++++++++++++++++++++++++
 2 files changed, 49 insertions(+), 1 deletion(-)

diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig
index ce5f5847d5d3..feeb8d2074ee 100644
--- a/drivers/clk/sunxi-ng/Kconfig
+++ b/drivers/clk/sunxi-ng/Kconfig
@@ -33,7 +33,7 @@ config SUN50I_H6_CCU
 	depends on (ARM64 && ARCH_SUNXI) || COMPILE_TEST
 
 config SUN50I_H6_R_CCU
-	bool "Support for the Allwinner H6 PRCM CCU"
+	bool "Support for the Allwinner H6 and H616 PRCM CCU"
 	default ARM64 && ARCH_SUNXI
 	depends on (ARM64 && ARCH_SUNXI) || COMPILE_TEST
 
diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c b/drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c
index 56e351b513f3..f8909a7ed553 100644
--- a/drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c
+++ b/drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c
@@ -139,6 +139,16 @@ static struct ccu_common *sun50i_h6_r_ccu_clks[] = {
 	&w1_clk.common,
 };
 
+static struct ccu_common *sun50i_h616_r_ccu_clks[] = {
+	&r_apb1_clk.common,
+	&r_apb2_clk.common,
+	&r_apb1_twd_clk.common,
+	&r_apb2_i2c_clk.common,
+	&r_apb2_rsb_clk.common,
+	&r_apb1_ir_clk.common,
+	&ir_clk.common,
+};
+
 static struct clk_hw_onecell_data sun50i_h6_r_hw_clks = {
 	.hws	= {
 		[CLK_AR100]		= &ar100_clk.common.hw,
@@ -159,6 +169,20 @@ static struct clk_hw_onecell_data sun50i_h6_r_hw_clks = {
 	.num	= CLK_NUMBER,
 };
 
+static struct clk_hw_onecell_data sun50i_h616_r_hw_clks = {
+	.hws	= {
+		[CLK_R_AHB]		= &r_ahb_clk.hw,
+		[CLK_R_APB1]		= &r_apb1_clk.common.hw,
+		[CLK_R_APB2]		= &r_apb2_clk.common.hw,
+		[CLK_R_APB1_TWD]	= &r_apb1_twd_clk.common.hw,
+		[CLK_R_APB2_I2C]	= &r_apb2_i2c_clk.common.hw,
+		[CLK_R_APB2_RSB]	= &r_apb2_rsb_clk.common.hw,
+		[CLK_R_APB1_IR]		= &r_apb1_ir_clk.common.hw,
+		[CLK_IR]		= &ir_clk.common.hw,
+	},
+	.num	= CLK_NUMBER,
+};
+
 static struct ccu_reset_map sun50i_h6_r_ccu_resets[] = {
 	[RST_R_APB1_TIMER]	=  { 0x11c, BIT(16) },
 	[RST_R_APB1_TWD]	=  { 0x12c, BIT(16) },
@@ -170,6 +194,13 @@ static struct ccu_reset_map sun50i_h6_r_ccu_resets[] = {
 	[RST_R_APB1_W1]		=  { 0x1ec, BIT(16) },
 };
 
+static struct ccu_reset_map sun50i_h616_r_ccu_resets[] = {
+	[RST_R_APB1_TWD]	=  { 0x12c, BIT(16) },
+	[RST_R_APB2_I2C]	=  { 0x19c, BIT(16) },
+	[RST_R_APB2_RSB]	=  { 0x1bc, BIT(16) },
+	[RST_R_APB1_IR]		=  { 0x1cc, BIT(16) },
+};
+
 static const struct sunxi_ccu_desc sun50i_h6_r_ccu_desc = {
 	.ccu_clks	= sun50i_h6_r_ccu_clks,
 	.num_ccu_clks	= ARRAY_SIZE(sun50i_h6_r_ccu_clks),
@@ -180,6 +211,16 @@ static const struct sunxi_ccu_desc sun50i_h6_r_ccu_desc = {
 	.num_resets	= ARRAY_SIZE(sun50i_h6_r_ccu_resets),
 };
 
+static const struct sunxi_ccu_desc sun50i_h616_r_ccu_desc = {
+	.ccu_clks	= sun50i_h616_r_ccu_clks,
+	.num_ccu_clks	= ARRAY_SIZE(sun50i_h616_r_ccu_clks),
+
+	.hw_clks	= &sun50i_h616_r_hw_clks,
+
+	.resets		= sun50i_h616_r_ccu_resets,
+	.num_resets	= ARRAY_SIZE(sun50i_h616_r_ccu_resets),
+};
+
 static void __init sunxi_r_ccu_init(struct device_node *node,
 				    const struct sunxi_ccu_desc *desc)
 {
@@ -200,3 +241,10 @@ static void __init sun50i_h6_r_ccu_setup(struct device_node *node)
 }
 CLK_OF_DECLARE(sun50i_h6_r_ccu, "allwinner,sun50i-h6-r-ccu",
 	       sun50i_h6_r_ccu_setup);
+
+static void __init sun50i_h616_r_ccu_setup(struct device_node *node)
+{
+	sunxi_r_ccu_init(node, &sun50i_h616_r_ccu_desc);
+}
+CLK_OF_DECLARE(sun50i_h616_r_ccu, "allwinner,sun50i-h616-r-ccu",
+	       sun50i_h616_r_ccu_setup);
-- 
2.17.5


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 03/20] clk: sunxi-ng: Add support for the Allwinner H616 CCU

[Andre Przywara]

While the clocks are fairly similar to the H6, many differ in tiny
details, so a separate clock driver seems indicated.

Derived from the H6 clock driver, and adjusted according to the manual.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
---
 drivers/clk/sunxi-ng/Kconfig                |    5 +
 drivers/clk/sunxi-ng/Makefile               |    1 +
 drivers/clk/sunxi-ng/ccu-sun50i-h616.c      | 1150 +++++++++++++++++++
 drivers/clk/sunxi-ng/ccu-sun50i-h616.h      |   56 +
 include/dt-bindings/clock/sun50i-h616-ccu.h |  115 ++
 include/dt-bindings/reset/sun50i-h616-ccu.h |   70 ++
 6 files changed, 1397 insertions(+)
 create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-h616.c
 create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-h616.h
 create mode 100644 include/dt-bindings/clock/sun50i-h616-ccu.h
 create mode 100644 include/dt-bindings/reset/sun50i-h616-ccu.h

diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig
index feeb8d2074ee..cd46d8853876 100644
--- a/drivers/clk/sunxi-ng/Kconfig
+++ b/drivers/clk/sunxi-ng/Kconfig
@@ -32,6 +32,11 @@ config SUN50I_H6_CCU
 	default ARM64 && ARCH_SUNXI
 	depends on (ARM64 && ARCH_SUNXI) || COMPILE_TEST
 
+config SUN50I_H616_CCU
+	bool "Support for the Allwinner H616 CCU"
+	default ARM64 && ARCH_SUNXI
+	depends on (ARM64 && ARCH_SUNXI) || COMPILE_TEST
+
 config SUN50I_H6_R_CCU
 	bool "Support for the Allwinner H6 and H616 PRCM CCU"
 	default ARM64 && ARCH_SUNXI
diff --git a/drivers/clk/sunxi-ng/Makefile b/drivers/clk/sunxi-ng/Makefile
index 3eb5cff40eac..96c324306d97 100644
--- a/drivers/clk/sunxi-ng/Makefile
+++ b/drivers/clk/sunxi-ng/Makefile
@@ -26,6 +26,7 @@ obj-$(CONFIG_SUN50I_A64_CCU)	+= ccu-sun50i-a64.o
 obj-$(CONFIG_SUN50I_A100_CCU)	+= ccu-sun50i-a100.o
 obj-$(CONFIG_SUN50I_A100_R_CCU)	+= ccu-sun50i-a100-r.o
 obj-$(CONFIG_SUN50I_H6_CCU)	+= ccu-sun50i-h6.o
+obj-$(CONFIG_SUN50I_H616_CCU)	+= ccu-sun50i-h616.o
 obj-$(CONFIG_SUN50I_H6_R_CCU)	+= ccu-sun50i-h6-r.o
 obj-$(CONFIG_SUN4I_A10_CCU)	+= ccu-sun4i-a10.o
 obj-$(CONFIG_SUN5I_CCU)		+= ccu-sun5i.o
diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-h616.c b/drivers/clk/sunxi-ng/ccu-sun50i-h616.c
new file mode 100644
index 000000000000..225307305880
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu-sun50i-h616.c
@@ -0,0 +1,1150 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2020 Arm Ltd.
+ * Based on the H6 CCU driver, which is:
+ *   Copyright (c) 2017 Icenowy Zheng <icenowy@aosc.io>
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/io.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+
+#include "ccu_common.h"
+#include "ccu_reset.h"
+
+#include "ccu_div.h"
+#include "ccu_gate.h"
+#include "ccu_mp.h"
+#include "ccu_mult.h"
+#include "ccu_nk.h"
+#include "ccu_nkm.h"
+#include "ccu_nkmp.h"
+#include "ccu_nm.h"
+
+#include "ccu-sun50i-h616.h"
+
+/*
+ * The CPU PLL is actually NP clock, with P being /1, /2 or /4. However
+ * P should only be used for output frequencies lower than 288 MHz.
+ *
+ * For now we can just model it as a multiplier clock, and force P to /1.
+ *
+ * The M factor is present in the register's description, but not in the
+ * frequency formula, and it's documented as "M is only used for backdoor
+ * testing", so it's not modelled and then force to 0.
+ */
+#define SUN50I_H616_PLL_CPUX_REG	0x000
+static struct ccu_mult pll_cpux_clk = {
+	.enable		= BIT(31),
+	.lock		= BIT(28),
+	.mult		= _SUNXI_CCU_MULT_MIN(8, 8, 12),
+	.common		= {
+		.reg		= 0x000,
+		.hw.init	= CLK_HW_INIT("pll-cpux", "osc24M",
+					      &ccu_mult_ops,
+					      CLK_SET_RATE_UNGATE),
+	},
+};
+
+/* Some PLLs are input * N / div1 / P. Model them as NKMP with no K */
+#define SUN50I_H616_PLL_DDR0_REG	0x010
+static struct ccu_nkmp pll_ddr0_clk = {
+	.enable		= BIT(31),
+	.lock		= BIT(28),
+	.n		= _SUNXI_CCU_MULT_MIN(8, 8, 12),
+	.m		= _SUNXI_CCU_DIV(1, 1), /* input divider */
+	.p		= _SUNXI_CCU_DIV(0, 1), /* output divider */
+	.common		= {
+		.reg		= 0x010,
+		.hw.init	= CLK_HW_INIT("pll-ddr0", "osc24M",
+					      &ccu_nkmp_ops,
+					      CLK_SET_RATE_UNGATE),
+	},
+};
+
+#define SUN50I_H616_PLL_DDR1_REG	0x018
+static struct ccu_nkmp pll_ddr1_clk = {
+	.enable		= BIT(31),
+	.lock		= BIT(28),
+	.n		= _SUNXI_CCU_MULT_MIN(8, 8, 12),
+	.m		= _SUNXI_CCU_DIV(1, 1), /* input divider */
+	.p		= _SUNXI_CCU_DIV(0, 1), /* output divider */
+	.common		= {
+		.reg		= 0x018,
+		.hw.init	= CLK_HW_INIT("pll-ddr1", "osc24M",
+					      &ccu_nkmp_ops,
+					      CLK_SET_RATE_UNGATE),
+	},
+};
+
+#define SUN50I_H616_PLL_PERIPH0_REG	0x020
+static struct ccu_nkmp pll_periph0_clk = {
+	.enable		= BIT(31),
+	.lock		= BIT(28),
+	.n		= _SUNXI_CCU_MULT_MIN(8, 8, 12),
+	.m		= _SUNXI_CCU_DIV(1, 1), /* input divider */
+	.p		= _SUNXI_CCU_DIV(0, 1), /* output divider */
+	.fixed_post_div	= 2,
+	.common		= {
+		.reg		= 0x020,
+		.features	= CCU_FEATURE_FIXED_POSTDIV,
+		.hw.init	= CLK_HW_INIT("pll-periph0", "osc24M",
+					      &ccu_nkmp_ops,
+					      CLK_SET_RATE_UNGATE),
+	},
+};
+
+#define SUN50I_H616_PLL_PERIPH1_REG	0x028
+static struct ccu_nkmp pll_periph1_clk = {
+	.enable		= BIT(31),
+	.lock		= BIT(28),
+	.n		= _SUNXI_CCU_MULT_MIN(8, 8, 12),
+	.m		= _SUNXI_CCU_DIV(1, 1), /* input divider */
+	.p		= _SUNXI_CCU_DIV(0, 1), /* output divider */
+	.fixed_post_div	= 2,
+	.common		= {
+		.reg		= 0x028,
+		.features	= CCU_FEATURE_FIXED_POSTDIV,
+		.hw.init	= CLK_HW_INIT("pll-periph1", "osc24M",
+					      &ccu_nkmp_ops,
+					      CLK_SET_RATE_UNGATE),
+	},
+};
+
+#define SUN50I_H616_PLL_GPU_REG		0x030
+static struct ccu_nkmp pll_gpu_clk = {
+	.enable		= BIT(31),
+	.lock		= BIT(28),
+	.n		= _SUNXI_CCU_MULT_MIN(8, 8, 12),
+	.m		= _SUNXI_CCU_DIV(1, 1), /* input divider */
+	.p		= _SUNXI_CCU_DIV(0, 1), /* output divider */
+	.common		= {
+		.reg		= 0x030,
+		.hw.init	= CLK_HW_INIT("pll-gpu", "osc24M",
+					      &ccu_nkmp_ops,
+					      CLK_SET_RATE_UNGATE),
+	},
+};
+
+/*
+ * For Video PLLs, the output divider is described as "used for testing"
+ * in the user manual. So it's not modelled and forced to 0.
+ */
+#define SUN50I_H616_PLL_VIDEO0_REG	0x040
+static struct ccu_nm pll_video0_clk = {
+	.enable		= BIT(31),
+	.lock		= BIT(28),
+	.n		= _SUNXI_CCU_MULT_MIN(8, 8, 12),
+	.m		= _SUNXI_CCU_DIV(1, 1), /* input divider */
+	.fixed_post_div	= 4,
+	.min_rate	= 288000000,
+	.max_rate	= 2400000000UL,
+	.common		= {
+		.reg		= 0x040,
+		.features	= CCU_FEATURE_FIXED_POSTDIV,
+		.hw.init	= CLK_HW_INIT("pll-video0", "osc24M",
+					      &ccu_nm_ops,
+					      CLK_SET_RATE_UNGATE),
+	},
+};
+
+#define SUN50I_H616_PLL_VIDEO1_REG	0x048
+static struct ccu_nm pll_video1_clk = {
+	.enable		= BIT(31),
+	.lock		= BIT(28),
+	.n		= _SUNXI_CCU_MULT_MIN(8, 8, 12),
+	.m		= _SUNXI_CCU_DIV(1, 1), /* input divider */
+	.fixed_post_div	= 4,
+	.min_rate	= 288000000,
+	.max_rate	= 2400000000UL,
+	.common		= {
+		.reg		= 0x048,
+		.features	= CCU_FEATURE_FIXED_POSTDIV,
+		.hw.init	= CLK_HW_INIT("pll-video1", "osc24M",
+					      &ccu_nm_ops,
+					      CLK_SET_RATE_UNGATE),
+	},
+};
+
+#define SUN50I_H616_PLL_VIDEO2_REG	0x050
+static struct ccu_nm pll_video2_clk = {
+	.enable		= BIT(31),
+	.lock		= BIT(28),
+	.n		= _SUNXI_CCU_MULT_MIN(8, 8, 12),
+	.m		= _SUNXI_CCU_DIV(1, 1), /* input divider */
+	.fixed_post_div	= 4,
+	.min_rate	= 288000000,
+	.max_rate	= 2400000000UL,
+	.common		= {
+		.reg		= 0x050,
+		.features	= CCU_FEATURE_FIXED_POSTDIV,
+		.hw.init	= CLK_HW_INIT("pll-video2", "osc24M",
+					      &ccu_nm_ops,
+					      CLK_SET_RATE_UNGATE),
+	},
+};
+
+#define SUN50I_H616_PLL_VE_REG		0x058
+static struct ccu_nkmp pll_ve_clk = {
+	.enable		= BIT(31),
+	.lock		= BIT(28),
+	.n		= _SUNXI_CCU_MULT_MIN(8, 8, 12),
+	.m		= _SUNXI_CCU_DIV(1, 1), /* input divider */
+	.p		= _SUNXI_CCU_DIV(0, 1), /* output divider */
+	.common		= {
+		.reg		= 0x058,
+		.hw.init	= CLK_HW_INIT("pll-ve", "osc24M",
+					      &ccu_nkmp_ops,
+					      CLK_SET_RATE_UNGATE),
+	},
+};
+
+#define SUN50I_H616_PLL_DE_REG		0x060
+static struct ccu_nkmp pll_de_clk = {
+	.enable		= BIT(31),
+	.lock		= BIT(28),
+	.n		= _SUNXI_CCU_MULT_MIN(8, 8, 12),
+	.m		= _SUNXI_CCU_DIV(1, 1), /* input divider */
+	.p		= _SUNXI_CCU_DIV(0, 1), /* output divider */
+	.common		= {
+		.reg		= 0x060,
+		.hw.init	= CLK_HW_INIT("pll-de", "osc24M",
+					      &ccu_nkmp_ops,
+					      CLK_SET_RATE_UNGATE),
+	},
+};
+
+/*
+ * TODO: Determine SDM settings for the audio PLL. The manual suggests
+ * PLL_FACTOR_N=16, PLL_POST_DIV_P=2, OUTPUT_DIV=2, pattern=0xe000c49b
+ * for 24.576 MHz, and PLL_FACTOR_N=22, PLL_POST_DIV_P=3, OUTPUT_DIV=2,
+ * pattern=0xe001288c for 22.5792 MHz.
+ * This clashes with our fixed PLL_POST_DIV_P.
+ */
+#define SUN50I_H616_PLL_AUDIO_REG	0x078
+static struct ccu_nm pll_audio_hs_clk = {
+	.enable		= BIT(31),
+	.lock		= BIT(28),
+	.n		= _SUNXI_CCU_MULT_MIN(8, 8, 12),
+	.m		= _SUNXI_CCU_DIV(1, 1), /* input divider */
+	.common		= {
+		.reg		= 0x078,
+		.hw.init	= CLK_HW_INIT("pll-audio-hs", "osc24M",
+					      &ccu_nm_ops,
+					      CLK_SET_RATE_UNGATE),
+	},
+};
+
+static const char * const cpux_parents[] = { "osc24M", "osc32k",
+					"iosc", "pll-cpux", "pll-periph0" };
+static SUNXI_CCU_MUX(cpux_clk, "cpux", cpux_parents,
+		     0x500, 24, 3, CLK_SET_RATE_PARENT | CLK_IS_CRITICAL);
+static SUNXI_CCU_M(axi_clk, "axi", "cpux", 0x500, 0, 2, 0);
+static SUNXI_CCU_M(cpux_apb_clk, "cpux-apb", "cpux", 0x500, 8, 2, 0);
+
+static const char * const psi_ahb1_ahb2_parents[] = { "osc24M", "osc32k",
+						      "iosc", "pll-periph0" };
+static SUNXI_CCU_MP_WITH_MUX(psi_ahb1_ahb2_clk, "psi-ahb1-ahb2",
+			     psi_ahb1_ahb2_parents,
+			     0x510,
+			     0, 2,	/* M */
+			     8, 2,	/* P */
+			     24, 2,	/* mux */
+			     0);
+
+static const char * const ahb3_apb1_apb2_parents[] = { "osc24M", "osc32k",
+						       "psi-ahb1-ahb2",
+						       "pll-periph0" };
+static SUNXI_CCU_MP_WITH_MUX(ahb3_clk, "ahb3", ahb3_apb1_apb2_parents, 0x51c,
+			     0, 2,	/* M */
+			     8, 2,	/* P */
+			     24, 2,	/* mux */
+			     0);
+
+static SUNXI_CCU_MP_WITH_MUX(apb1_clk, "apb1", ahb3_apb1_apb2_parents, 0x520,
+			     0, 2,	/* M */
+			     8, 2,	/* P */
+			     24, 2,	/* mux */
+			     0);
+
+static SUNXI_CCU_MP_WITH_MUX(apb2_clk, "apb2", ahb3_apb1_apb2_parents, 0x524,
+			     0, 2,	/* M */
+			     8, 2,	/* P */
+			     24, 2,	/* mux */
+			     0);
+
+static const char * const mbus_parents[] = { "osc24M", "pll-periph0-2x",
+					     "pll-ddr0", "pll-ddr1" };
+static SUNXI_CCU_M_WITH_MUX_GATE(mbus_clk, "mbus", mbus_parents, 0x540,
+					0, 3,	/* M */
+					24, 2,	/* mux */
+					BIT(31),	/* gate */
+					CLK_IS_CRITICAL);
+
+static const char * const de_parents[] = { "pll-de", "pll-periph0-2x" };
+static SUNXI_CCU_M_WITH_MUX_GATE(de_clk, "de", de_parents, 0x600,
+				       0, 4,	/* M */
+				       24, 1,	/* mux */
+				       BIT(31),	/* gate */
+				       CLK_SET_RATE_PARENT);
+
+static SUNXI_CCU_GATE(bus_de_clk, "bus-de", "psi-ahb1-ahb2",
+		      0x60c, BIT(0), 0);
+
+static SUNXI_CCU_M_WITH_MUX_GATE(deinterlace_clk, "deinterlace",
+				       de_parents,
+				       0x620,
+				       0, 4,	/* M */
+				       24, 1,	/* mux */
+				       BIT(31),	/* gate */
+				       0);
+
+static SUNXI_CCU_GATE(bus_deinterlace_clk, "bus-deinterlace", "psi-ahb1-ahb2",
+		      0x62c, BIT(0), 0);
+
+static SUNXI_CCU_M_WITH_MUX_GATE(g2d_clk, "g2d", de_parents, 0x630,
+				       0, 4,	/* M */
+				       24, 1,	/* mux */
+				       BIT(31),	/* gate */
+				       0);
+
+static SUNXI_CCU_GATE(bus_g2d_clk, "bus-g2d", "psi-ahb1-ahb2",
+		      0x63c, BIT(0), 0);
+
+static const char * const gpu0_parents[] = { "pll-gpu", "gpu1" };
+static SUNXI_CCU_M_WITH_MUX_GATE(gpu0_clk, "gpu0", gpu0_parents, 0x670,
+				       0, 2,	/* M */
+				       24, 1,	/* mux */
+				       BIT(31),	/* gate */
+				       CLK_SET_RATE_PARENT);
+static SUNXI_CCU_M_WITH_GATE(gpu1_clk, "gpu1", "pll-periph0-2x", 0x674,
+					0, 2,	/* M */
+					BIT(31),/* gate */
+					0);
+
+static SUNXI_CCU_GATE(bus_gpu_clk, "bus-gpu", "psi-ahb1-ahb2",
+		      0x67c, BIT(0), 0);
+
+static const char * const ce_parents[] = { "osc24M", "pll-periph0-2x" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(ce_clk, "ce", ce_parents, 0x680,
+					0, 4,	/* M */
+					8, 2,	/* N */
+					24, 1,	/* mux */
+					BIT(31),/* gate */
+					0);
+
+static SUNXI_CCU_GATE(bus_ce_clk, "bus-ce", "psi-ahb1-ahb2",
+		      0x68c, BIT(0), 0);
+
+static const char * const ve_parents[] = { "pll-ve" };
+static SUNXI_CCU_M_WITH_MUX_GATE(ve_clk, "ve", ve_parents, 0x690,
+				       0, 3,	/* M */
+				       24, 1,	/* mux */
+				       BIT(31),	/* gate */
+				       CLK_SET_RATE_PARENT);
+
+static SUNXI_CCU_GATE(bus_ve_clk, "bus-ve", "psi-ahb1-ahb2",
+		      0x69c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_dma_clk, "bus-dma", "psi-ahb1-ahb2",
+		      0x70c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_hstimer_clk, "bus-hstimer", "psi-ahb1-ahb2",
+		      0x73c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(avs_clk, "avs", "osc24M", 0x740, BIT(31), 0);
+
+static SUNXI_CCU_GATE(bus_dbg_clk, "bus-dbg", "psi-ahb1-ahb2",
+		      0x78c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_psi_clk, "bus-psi", "psi-ahb1-ahb2",
+		      0x79c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_pwm_clk, "bus-pwm", "apb1", 0x7ac, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_iommu_clk, "bus-iommu", "apb1", 0x7bc, BIT(0), 0);
+
+static const char * const dram_parents[] = { "pll-ddr0", "pll-ddr1" };
+static struct ccu_div dram_clk = {
+	.div		= _SUNXI_CCU_DIV(0, 2),
+	.mux		= _SUNXI_CCU_MUX(24, 2),
+	.common	= {
+		.reg		= 0x800,
+		.hw.init	= CLK_HW_INIT_PARENTS("dram",
+						      dram_parents,
+						      &ccu_div_ops,
+						      CLK_IS_CRITICAL),
+	},
+};
+
+static SUNXI_CCU_GATE(mbus_dma_clk, "mbus-dma", "mbus",
+		      0x804, BIT(0), 0);
+static SUNXI_CCU_GATE(mbus_ve_clk, "mbus-ve", "mbus",
+		      0x804, BIT(1), 0);
+static SUNXI_CCU_GATE(mbus_ce_clk, "mbus-ce", "mbus",
+		      0x804, BIT(2), 0);
+static SUNXI_CCU_GATE(mbus_ts_clk, "mbus-ts", "mbus",
+		      0x804, BIT(3), 0);
+static SUNXI_CCU_GATE(mbus_nand_clk, "mbus-nand", "mbus",
+		      0x804, BIT(5), 0);
+static SUNXI_CCU_GATE(mbus_g2d_clk, "mbus-g2d", "mbus",
+		      0x804, BIT(10), 0);
+
+static SUNXI_CCU_GATE(bus_dram_clk, "bus-dram", "psi-ahb1-ahb2",
+		      0x80c, BIT(0), CLK_IS_CRITICAL);
+
+static const char * const nand_spi_parents[] = { "osc24M", "pll-periph0",
+					     "pll-periph1", "pll-periph0-2x",
+					     "pll-periph1-2x" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(nand0_clk, "nand0", nand_spi_parents, 0x810,
+					0, 4,	/* M */
+					8, 2,	/* N */
+					24, 3,	/* mux */
+					BIT(31),/* gate */
+					0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(nand1_clk, "nand1", nand_spi_parents, 0x814,
+					0, 4,	/* M */
+					8, 2,	/* N */
+					24, 3,	/* mux */
+					BIT(31),/* gate */
+					0);
+
+static SUNXI_CCU_GATE(bus_nand_clk, "bus-nand", "ahb3", 0x82c, BIT(0), 0);
+
+static const char * const mmc_parents[] = { "osc24M", "pll-periph0-2x",
+					    "pll-periph1-2x" };
+static SUNXI_CCU_MP_WITH_MUX_GATE_POSTDIV(mmc0_clk, "mmc0", mmc_parents, 0x830,
+					  0, 4,		/* M */
+					  8, 2,		/* N */
+					  24, 2,	/* mux */
+					  BIT(31),	/* gate */
+					  2,		/* post-div */
+					  0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE_POSTDIV(mmc1_clk, "mmc1", mmc_parents, 0x834,
+					  0, 4,		/* M */
+					  8, 2,		/* N */
+					  24, 2,	/* mux */
+					  BIT(31),	/* gate */
+					  2,		/* post-div */
+					  0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE_POSTDIV(mmc2_clk, "mmc2", mmc_parents, 0x838,
+					  0, 4,		/* M */
+					  8, 2,		/* N */
+					  24, 2,	/* mux */
+					  BIT(31),	/* gate */
+					  2,		/* post-div */
+					  0);
+
+static SUNXI_CCU_GATE(bus_mmc0_clk, "bus-mmc0", "ahb3", 0x84c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_mmc1_clk, "bus-mmc1", "ahb3", 0x84c, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_mmc2_clk, "bus-mmc2", "ahb3", 0x84c, BIT(2), 0);
+
+static SUNXI_CCU_GATE(bus_uart0_clk, "bus-uart0", "apb2", 0x90c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_uart1_clk, "bus-uart1", "apb2", 0x90c, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_uart2_clk, "bus-uart2", "apb2", 0x90c, BIT(2), 0);
+static SUNXI_CCU_GATE(bus_uart3_clk, "bus-uart3", "apb2", 0x90c, BIT(3), 0);
+static SUNXI_CCU_GATE(bus_uart4_clk, "bus-uart4", "apb2", 0x90c, BIT(4), 0);
+static SUNXI_CCU_GATE(bus_uart5_clk, "bus-uart5", "apb2", 0x90c, BIT(5), 0);
+
+static SUNXI_CCU_GATE(bus_i2c0_clk, "bus-i2c0", "apb2", 0x91c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_i2c1_clk, "bus-i2c1", "apb2", 0x91c, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_i2c2_clk, "bus-i2c2", "apb2", 0x91c, BIT(2), 0);
+static SUNXI_CCU_GATE(bus_i2c3_clk, "bus-i2c3", "apb2", 0x91c, BIT(3), 0);
+static SUNXI_CCU_GATE(bus_i2c4_clk, "bus-i2c4", "apb2", 0x91c, BIT(4), 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(spi0_clk, "spi0", nand_spi_parents, 0x940,
+					0, 4,	/* M */
+					8, 2,	/* N */
+					24, 3,	/* mux */
+					BIT(31),/* gate */
+					0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(spi1_clk, "spi1", nand_spi_parents, 0x944,
+					0, 4,	/* M */
+					8, 2,	/* N */
+					24, 3,	/* mux */
+					BIT(31),/* gate */
+					0);
+
+static SUNXI_CCU_GATE(bus_spi0_clk, "bus-spi0", "ahb3", 0x96c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_spi1_clk, "bus-spi1", "ahb3", 0x96c, BIT(1), 0);
+
+static SUNXI_CCU_GATE(emac_25m_clk, "emac-25m", "ahb3", 0x970,
+		      BIT(31) | BIT(30), 0);
+
+static SUNXI_CCU_GATE(bus_emac0_clk, "bus-emac0", "ahb3", 0x97c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_emac1_clk, "bus-emac1", "ahb3", 0x97c, BIT(1), 0);
+
+static const char * const ts_parents[] = { "osc24M", "pll-periph0" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(ts_clk, "ts", ts_parents, 0x9b0,
+					0, 4,	/* M */
+					8, 2,	/* N */
+					24, 1,	/* mux */
+					BIT(31),/* gate */
+					0);
+
+static SUNXI_CCU_GATE(bus_ts_clk, "bus-ts", "ahb3", 0x9bc, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_ths_clk, "bus-ths", "apb1", 0x9fc, BIT(0), 0);
+
+static const char * const audio_parents[] = { "pll-audio-1x", "pll-audio-2x",
+					      "pll-audio-4x", "pll-audio-hs" };
+static struct ccu_div spdif_clk = {
+	.enable		= BIT(31),
+	.div		= _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+	.mux		= _SUNXI_CCU_MUX(24, 2),
+	.common		= {
+		.reg		= 0xa20,
+		.hw.init	= CLK_HW_INIT_PARENTS("spdif",
+						      audio_parents,
+						      &ccu_div_ops,
+						      0),
+	},
+};
+
+static SUNXI_CCU_GATE(bus_spdif_clk, "bus-spdif", "apb1", 0xa2c, BIT(0), 0);
+
+static struct ccu_div dmic_clk = {
+	.enable		= BIT(31),
+	.div		= _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+	.mux		= _SUNXI_CCU_MUX(24, 2),
+	.common		= {
+		.reg		= 0xa40,
+		.hw.init	= CLK_HW_INIT_PARENTS("dmic",
+						      audio_parents,
+						      &ccu_div_ops,
+						      0),
+	},
+};
+
+static SUNXI_CCU_GATE(bus_dmic_clk, "bus-dmic", "apb1", 0xa4c, BIT(0), 0);
+
+static SUNXI_CCU_M_WITH_MUX_GATE(audio_codec_1x_clk, "audio-codec-1x",
+				 audio_parents, 0xa50,
+				 0, 4,	/* M */
+				 24, 2,	/* mux */
+				 BIT(31),	/* gate */
+				 CLK_SET_RATE_PARENT);
+static SUNXI_CCU_M_WITH_MUX_GATE(audio_codec_4x_clk, "audio-codec-4x",
+				 audio_parents, 0xa54,
+				 0, 4,	/* M */
+				 24, 2,	/* mux */
+				 BIT(31),	/* gate */
+				 CLK_SET_RATE_PARENT);
+
+static SUNXI_CCU_GATE(bus_audio_codec_clk, "bus-audio-codec", "apb1", 0xa5c,
+		BIT(0), 0);
+
+static struct ccu_div audio_hub_clk = {
+	.enable		= BIT(31),
+	.div		= _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+	.mux		= _SUNXI_CCU_MUX(24, 2),
+	.common		= {
+		.reg		= 0xa60,
+		.hw.init	= CLK_HW_INIT_PARENTS("audio-hub",
+						      audio_parents,
+						      &ccu_div_ops,
+						      0),
+	},
+};
+
+static SUNXI_CCU_GATE(bus_audio_hub_clk, "bus-audio-hub", "apb1", 0xa6c, BIT(0), 0);
+
+/*
+ * There are OHCI 12M clock source selection bits for the four USB 2.0 ports.
+ * We will force them to 0 (12M divided from 48M).
+ */
+#define SUN50I_H616_USB0_CLK_REG		0xa70
+#define SUN50I_H616_USB1_CLK_REG		0xa74
+#define SUN50I_H616_USB2_CLK_REG		0xa78
+#define SUN50I_H616_USB3_CLK_REG		0xa7c
+
+static SUNXI_CCU_GATE(usb_ohci0_clk, "usb-ohci0", "osc12M", 0xa70, BIT(31), 0);
+static SUNXI_CCU_GATE(usb_phy0_clk, "usb-phy0", "osc24M", 0xa70, BIT(29), 0);
+
+static SUNXI_CCU_GATE(usb_ohci1_clk, "usb-ohci1", "osc12M", 0xa74, BIT(31), 0);
+static SUNXI_CCU_GATE(usb_phy1_clk, "usb-phy1", "osc24M", 0xa74, BIT(29), 0);
+
+static SUNXI_CCU_GATE(usb_ohci2_clk, "usb-ohci2", "osc12M", 0xa78, BIT(31), 0);
+static SUNXI_CCU_GATE(usb_phy2_clk, "usb-phy2", "osc24M", 0xa78, BIT(29), 0);
+
+static SUNXI_CCU_GATE(usb_ohci3_clk, "usb-ohci3", "osc12M", 0xa7c, BIT(31), 0);
+static SUNXI_CCU_GATE(usb_phy3_clk, "usb-phy3", "osc24M", 0xa7c, BIT(29), 0);
+
+static SUNXI_CCU_GATE(bus_ohci0_clk, "bus-ohci0", "ahb3", 0xa8c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_ohci1_clk, "bus-ohci1", "ahb3", 0xa8c, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_ohci2_clk, "bus-ohci2", "ahb3", 0xa8c, BIT(2), 0);
+static SUNXI_CCU_GATE(bus_ohci3_clk, "bus-ohci3", "ahb3", 0xa8c, BIT(3), 0);
+static SUNXI_CCU_GATE(bus_ehci0_clk, "bus-ehci0", "ahb3", 0xa8c, BIT(4), 0);
+static SUNXI_CCU_GATE(bus_ehci1_clk, "bus-ehci1", "ahb3", 0xa8c, BIT(5), 0);
+static SUNXI_CCU_GATE(bus_ehci2_clk, "bus-ehci2", "ahb3", 0xa8c, BIT(6), 0);
+static SUNXI_CCU_GATE(bus_ehci3_clk, "bus-ehci3", "ahb3", 0xa8c, BIT(7), 0);
+static SUNXI_CCU_GATE(bus_otg_clk, "bus-otg", "ahb3", 0xa8c, BIT(8), 0);
+
+static SUNXI_CCU_GATE(bus_keyadc_clk, "bus-keyadc", "apb1", 0xa9c, BIT(0), 0);
+
+static const char * const hdmi_parents[] = { "pll-video0", "pll-video0-4x",
+					     "pll-video2", "pll-video2-4x" };
+static SUNXI_CCU_M_WITH_MUX_GATE(hdmi_clk, "hdmi", hdmi_parents, 0xb00,
+				 0, 4,		/* M */
+				 24, 2,		/* mux */
+				 BIT(31),	/* gate */
+				 0);
+
+static SUNXI_CCU_GATE(hdmi_slow_clk, "hdmi-slow", "osc24M", 0xb04, BIT(31), 0);
+
+static const char * const hdmi_cec_parents[] = { "osc32k", "pll-periph0-2x" };
+static const struct ccu_mux_fixed_prediv hdmi_cec_predivs[] = {
+	{ .index = 1, .div = 36621 },
+};
+
+#define SUN50I_H616_HDMI_CEC_CLK_REG		0xb10
+static struct ccu_mux hdmi_cec_clk = {
+	.enable		= BIT(31) | BIT(30),
+
+	.mux		= {
+		.shift	= 24,
+		.width	= 2,
+
+		.fixed_predivs	= hdmi_cec_predivs,
+		.n_predivs	= ARRAY_SIZE(hdmi_cec_predivs),
+	},
+
+	.common		= {
+		.reg		= 0xb10,
+		.features	= CCU_FEATURE_FIXED_PREDIV,
+		.hw.init	= CLK_HW_INIT_PARENTS("hdmi-cec",
+						      hdmi_cec_parents,
+						      &ccu_mux_ops,
+						      0),
+	},
+};
+
+static SUNXI_CCU_GATE(bus_hdmi_clk, "bus-hdmi", "ahb3", 0xb1c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_tcon_top_clk, "bus-tcon-top", "ahb3",
+		      0xb5c, BIT(0), 0);
+
+static const char * const tcon_tv_parents[] = { "pll-video0",
+						"pll-video0-4x",
+						"pll-video1",
+						"pll-video1-4x" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(tcon_tv0_clk, "tcon-tv0",
+				  tcon_tv_parents, 0xb80,
+				  0, 4,		/* M */
+				  8, 2,		/* P */
+				  24, 3,	/* mux */
+				  BIT(31),	/* gate */
+				  CLK_SET_RATE_PARENT);
+static SUNXI_CCU_MP_WITH_MUX_GATE(tcon_tv1_clk, "tcon-tv1",
+				  tcon_tv_parents, 0xb84,
+				  0, 4,		/* M */
+				  8, 2,		/* P */
+				  24, 3,	/* mux */
+				  BIT(31),	/* gate */
+				  CLK_SET_RATE_PARENT);
+
+static SUNXI_CCU_GATE(bus_tcon_tv0_clk, "bus-tcon-tv0", "ahb3",
+		      0xb9c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_tcon_tv1_clk, "bus-tcon-tv1", "ahb3",
+		      0xb9c, BIT(1), 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(tve0_clk, "tve0",
+				  tcon_tv_parents, 0xbb0,
+				  0, 4,		/* M */
+				  8, 2,		/* P */
+				  24, 3,	/* mux */
+				  BIT(31),	/* gate */
+				  CLK_SET_RATE_PARENT);
+
+static SUNXI_CCU_GATE(bus_tve_top_clk, "bus-tve-top", "ahb3",
+		      0xbbc, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_tve0_clk, "bus-tve0", "ahb3",
+		      0xbbc, BIT(1), 0);
+
+static const char * const hdcp_parents[] = { "pll-periph0", "pll-periph1" };
+static SUNXI_CCU_M_WITH_MUX_GATE(hdcp_clk, "hdcp", hdcp_parents, 0xc40,
+				 0, 4,		/* M */
+				 24, 2,		/* mux */
+				 BIT(31),	/* gate */
+				 0);
+
+static SUNXI_CCU_GATE(bus_hdcp_clk, "bus-hdcp", "ahb3", 0xc4c, BIT(0), 0);
+
+/* Fixed factor clocks */
+static CLK_FIXED_FACTOR_FW_NAME(osc12M_clk, "osc12M", "hosc", 2, 1, 0);
+
+static const struct clk_hw *clk_parent_pll_audio[] = {
+	&pll_audio_hs_clk.common.hw
+};
+
+/*
+ * The divider of pll-audio is fixed to 24 for now, so 24576000 and 22579200
+ * rates can be set exactly in conjunction with sigma-delta modulation.
+ */
+static CLK_FIXED_FACTOR_HWS(pll_audio_1x_clk, "pll-audio-1x",
+			    clk_parent_pll_audio,
+			    96, 1, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR_HWS(pll_audio_2x_clk, "pll-audio-2x",
+			    clk_parent_pll_audio,
+			    48, 1, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR_HWS(pll_audio_4x_clk, "pll-audio-4x",
+			    clk_parent_pll_audio,
+			    24, 1, CLK_SET_RATE_PARENT);
+
+static const struct clk_hw *pll_periph0_parents[] = {
+	&pll_periph0_clk.common.hw
+};
+
+static CLK_FIXED_FACTOR_HWS(pll_periph0_2x_clk, "pll-periph0-2x",
+			    pll_periph0_parents,
+			    1, 2, 0);
+
+static const struct clk_hw *pll_periph1_parents[] = {
+	&pll_periph1_clk.common.hw
+};
+
+static CLK_FIXED_FACTOR_HWS(pll_periph1_2x_clk, "pll-periph1-2x",
+			    pll_periph1_parents,
+			    1, 2, 0);
+
+static CLK_FIXED_FACTOR_HW(pll_video0_4x_clk, "pll-video0-4x",
+			   &pll_video0_clk.common.hw,
+			   1, 4, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR_HW(pll_video1_4x_clk, "pll-video1-4x",
+			   &pll_video1_clk.common.hw,
+			   1, 4, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR_HW(pll_video2_4x_clk, "pll-video2-4x",
+			   &pll_video2_clk.common.hw,
+			   1, 4, CLK_SET_RATE_PARENT);
+
+static struct ccu_common *sun50i_h616_ccu_clks[] = {
+	&pll_cpux_clk.common,
+	&pll_ddr0_clk.common,
+	&pll_ddr1_clk.common,
+	&pll_periph0_clk.common,
+	&pll_periph1_clk.common,
+	&pll_gpu_clk.common,
+	&pll_video0_clk.common,
+	&pll_video1_clk.common,
+	&pll_video2_clk.common,
+	&pll_ve_clk.common,
+	&pll_de_clk.common,
+	&pll_audio_hs_clk.common,
+	&cpux_clk.common,
+	&axi_clk.common,
+	&cpux_apb_clk.common,
+	&psi_ahb1_ahb2_clk.common,
+	&ahb3_clk.common,
+	&apb1_clk.common,
+	&apb2_clk.common,
+	&mbus_clk.common,
+	&de_clk.common,
+	&bus_de_clk.common,
+	&deinterlace_clk.common,
+	&bus_deinterlace_clk.common,
+	&g2d_clk.common,
+	&bus_g2d_clk.common,
+	&gpu0_clk.common,
+	&bus_gpu_clk.common,
+	&gpu1_clk.common,
+	&ce_clk.common,
+	&bus_ce_clk.common,
+	&ve_clk.common,
+	&bus_ve_clk.common,
+	&bus_dma_clk.common,
+	&bus_hstimer_clk.common,
+	&avs_clk.common,
+	&bus_dbg_clk.common,
+	&bus_psi_clk.common,
+	&bus_pwm_clk.common,
+	&bus_iommu_clk.common,
+	&dram_clk.common,
+	&mbus_dma_clk.common,
+	&mbus_ve_clk.common,
+	&mbus_ce_clk.common,
+	&mbus_ts_clk.common,
+	&mbus_nand_clk.common,
+	&mbus_g2d_clk.common,
+	&bus_dram_clk.common,
+	&nand0_clk.common,
+	&nand1_clk.common,
+	&bus_nand_clk.common,
+	&mmc0_clk.common,
+	&mmc1_clk.common,
+	&mmc2_clk.common,
+	&bus_mmc0_clk.common,
+	&bus_mmc1_clk.common,
+	&bus_mmc2_clk.common,
+	&bus_uart0_clk.common,
+	&bus_uart1_clk.common,
+	&bus_uart2_clk.common,
+	&bus_uart3_clk.common,
+	&bus_uart4_clk.common,
+	&bus_uart5_clk.common,
+	&bus_i2c0_clk.common,
+	&bus_i2c1_clk.common,
+	&bus_i2c2_clk.common,
+	&bus_i2c3_clk.common,
+	&bus_i2c4_clk.common,
+	&spi0_clk.common,
+	&spi1_clk.common,
+	&bus_spi0_clk.common,
+	&bus_spi1_clk.common,
+	&emac_25m_clk.common,
+	&bus_emac0_clk.common,
+	&bus_emac1_clk.common,
+	&ts_clk.common,
+	&bus_ts_clk.common,
+	&bus_ths_clk.common,
+	&spdif_clk.common,
+	&bus_spdif_clk.common,
+	&dmic_clk.common,
+	&bus_dmic_clk.common,
+	&audio_codec_1x_clk.common,
+	&audio_codec_4x_clk.common,
+	&bus_audio_codec_clk.common,
+	&audio_hub_clk.common,
+	&bus_audio_hub_clk.common,
+	&usb_ohci0_clk.common,
+	&usb_phy0_clk.common,
+	&usb_ohci1_clk.common,
+	&usb_phy1_clk.common,
+	&usb_ohci2_clk.common,
+	&usb_phy2_clk.common,
+	&usb_ohci3_clk.common,
+	&usb_phy3_clk.common,
+	&bus_ohci0_clk.common,
+	&bus_ohci1_clk.common,
+	&bus_ohci2_clk.common,
+	&bus_ohci3_clk.common,
+	&bus_ehci0_clk.common,
+	&bus_ehci1_clk.common,
+	&bus_ehci2_clk.common,
+	&bus_ehci3_clk.common,
+	&bus_otg_clk.common,
+	&bus_keyadc_clk.common,
+	&hdmi_clk.common,
+	&hdmi_slow_clk.common,
+	&hdmi_cec_clk.common,
+	&bus_hdmi_clk.common,
+	&bus_tcon_top_clk.common,
+	&tcon_tv0_clk.common,
+	&tcon_tv1_clk.common,
+	&bus_tcon_tv0_clk.common,
+	&bus_tcon_tv1_clk.common,
+	&tve0_clk.common,
+	&bus_tve_top_clk.common,
+	&bus_tve0_clk.common,
+	&hdcp_clk.common,
+	&bus_hdcp_clk.common,
+};
+
+static struct clk_hw_onecell_data sun50i_h616_hw_clks = {
+	.hws	= {
+		[CLK_OSC12M]		= &osc12M_clk.hw,
+		[CLK_PLL_CPUX]		= &pll_cpux_clk.common.hw,
+		[CLK_PLL_DDR0]		= &pll_ddr0_clk.common.hw,
+		[CLK_PLL_DDR1]		= &pll_ddr1_clk.common.hw,
+		[CLK_PLL_PERIPH0]	= &pll_periph0_clk.common.hw,
+		[CLK_PLL_PERIPH0_2X]	= &pll_periph0_2x_clk.hw,
+		[CLK_PLL_PERIPH1]	= &pll_periph1_clk.common.hw,
+		[CLK_PLL_PERIPH1_2X]	= &pll_periph1_2x_clk.hw,
+		[CLK_PLL_GPU]		= &pll_gpu_clk.common.hw,
+		[CLK_PLL_VIDEO0]	= &pll_video0_clk.common.hw,
+		[CLK_PLL_VIDEO0_4X]	= &pll_video0_4x_clk.hw,
+		[CLK_PLL_VIDEO1]	= &pll_video1_clk.common.hw,
+		[CLK_PLL_VIDEO1_4X]	= &pll_video1_4x_clk.hw,
+		[CLK_PLL_VIDEO2]	= &pll_video2_clk.common.hw,
+		[CLK_PLL_VIDEO2_4X]	= &pll_video2_4x_clk.hw,
+		[CLK_PLL_VE]		= &pll_ve_clk.common.hw,
+		[CLK_PLL_DE]		= &pll_de_clk.common.hw,
+		[CLK_PLL_AUDIO_HS]	= &pll_audio_hs_clk.common.hw,
+		[CLK_PLL_AUDIO_1X]	= &pll_audio_1x_clk.hw,
+		[CLK_PLL_AUDIO_2X]	= &pll_audio_2x_clk.hw,
+		[CLK_PLL_AUDIO_4X]	= &pll_audio_4x_clk.hw,
+		[CLK_CPUX]		= &cpux_clk.common.hw,
+		[CLK_AXI]		= &axi_clk.common.hw,
+		[CLK_CPUX_APB]		= &cpux_apb_clk.common.hw,
+		[CLK_PSI_AHB1_AHB2]	= &psi_ahb1_ahb2_clk.common.hw,
+		[CLK_AHB3]		= &ahb3_clk.common.hw,
+		[CLK_APB1]		= &apb1_clk.common.hw,
+		[CLK_APB2]		= &apb2_clk.common.hw,
+		[CLK_MBUS]		= &mbus_clk.common.hw,
+		[CLK_DE]		= &de_clk.common.hw,
+		[CLK_BUS_DE]		= &bus_de_clk.common.hw,
+		[CLK_DEINTERLACE]	= &deinterlace_clk.common.hw,
+		[CLK_BUS_DEINTERLACE]	= &bus_deinterlace_clk.common.hw,
+		[CLK_G2D]		= &g2d_clk.common.hw,
+		[CLK_BUS_G2D]		= &bus_g2d_clk.common.hw,
+		[CLK_GPU0]		= &gpu0_clk.common.hw,
+		[CLK_BUS_GPU]		= &bus_gpu_clk.common.hw,
+		[CLK_GPU1]		= &gpu1_clk.common.hw,
+		[CLK_CE]		= &ce_clk.common.hw,
+		[CLK_BUS_CE]		= &bus_ce_clk.common.hw,
+		[CLK_VE]		= &ve_clk.common.hw,
+		[CLK_BUS_VE]		= &bus_ve_clk.common.hw,
+		[CLK_BUS_DMA]		= &bus_dma_clk.common.hw,
+		[CLK_BUS_HSTIMER]	= &bus_hstimer_clk.common.hw,
+		[CLK_AVS]		= &avs_clk.common.hw,
+		[CLK_BUS_DBG]		= &bus_dbg_clk.common.hw,
+		[CLK_BUS_PSI]		= &bus_psi_clk.common.hw,
+		[CLK_BUS_PWM]		= &bus_pwm_clk.common.hw,
+		[CLK_BUS_IOMMU]		= &bus_iommu_clk.common.hw,
+		[CLK_DRAM]		= &dram_clk.common.hw,
+		[CLK_MBUS_DMA]		= &mbus_dma_clk.common.hw,
+		[CLK_MBUS_VE]		= &mbus_ve_clk.common.hw,
+		[CLK_MBUS_CE]		= &mbus_ce_clk.common.hw,
+		[CLK_MBUS_TS]		= &mbus_ts_clk.common.hw,
+		[CLK_MBUS_NAND]		= &mbus_nand_clk.common.hw,
+		[CLK_MBUS_G2D]		= &mbus_g2d_clk.common.hw,
+		[CLK_BUS_DRAM]		= &bus_dram_clk.common.hw,
+		[CLK_NAND0]		= &nand0_clk.common.hw,
+		[CLK_NAND1]		= &nand1_clk.common.hw,
+		[CLK_BUS_NAND]		= &bus_nand_clk.common.hw,
+		[CLK_MMC0]		= &mmc0_clk.common.hw,
+		[CLK_MMC1]		= &mmc1_clk.common.hw,
+		[CLK_MMC2]		= &mmc2_clk.common.hw,
+		[CLK_BUS_MMC0]		= &bus_mmc0_clk.common.hw,
+		[CLK_BUS_MMC1]		= &bus_mmc1_clk.common.hw,
+		[CLK_BUS_MMC2]		= &bus_mmc2_clk.common.hw,
+		[CLK_BUS_UART0]		= &bus_uart0_clk.common.hw,
+		[CLK_BUS_UART1]		= &bus_uart1_clk.common.hw,
+		[CLK_BUS_UART2]		= &bus_uart2_clk.common.hw,
+		[CLK_BUS_UART3]		= &bus_uart3_clk.common.hw,
+		[CLK_BUS_UART4]		= &bus_uart4_clk.common.hw,
+		[CLK_BUS_UART5]		= &bus_uart5_clk.common.hw,
+		[CLK_BUS_I2C0]		= &bus_i2c0_clk.common.hw,
+		[CLK_BUS_I2C1]		= &bus_i2c1_clk.common.hw,
+		[CLK_BUS_I2C2]		= &bus_i2c2_clk.common.hw,
+		[CLK_BUS_I2C3]		= &bus_i2c3_clk.common.hw,
+		[CLK_BUS_I2C4]		= &bus_i2c4_clk.common.hw,
+		[CLK_SPI0]		= &spi0_clk.common.hw,
+		[CLK_SPI1]		= &spi1_clk.common.hw,
+		[CLK_BUS_SPI0]		= &bus_spi0_clk.common.hw,
+		[CLK_BUS_SPI1]		= &bus_spi1_clk.common.hw,
+		[CLK_EMAC_25M]		= &emac_25m_clk.common.hw,
+		[CLK_BUS_EMAC0]		= &bus_emac0_clk.common.hw,
+		[CLK_BUS_EMAC1]		= &bus_emac1_clk.common.hw,
+		[CLK_TS]		= &ts_clk.common.hw,
+		[CLK_BUS_TS]		= &bus_ts_clk.common.hw,
+		[CLK_BUS_THS]		= &bus_ths_clk.common.hw,
+		[CLK_SPDIF]		= &spdif_clk.common.hw,
+		[CLK_BUS_SPDIF]		= &bus_spdif_clk.common.hw,
+		[CLK_DMIC]		= &dmic_clk.common.hw,
+		[CLK_BUS_DMIC]		= &bus_dmic_clk.common.hw,
+		[CLK_AUDIO_CODEC_1X]	= &audio_codec_1x_clk.common.hw,
+		[CLK_AUDIO_CODEC_4X]	= &audio_codec_4x_clk.common.hw,
+		[CLK_BUS_AUDIO_CODEC]	= &bus_audio_codec_clk.common.hw,
+		[CLK_AUDIO_HUB]		= &audio_hub_clk.common.hw,
+		[CLK_BUS_AUDIO_HUB]	= &bus_audio_hub_clk.common.hw,
+		[CLK_USB_OHCI0]		= &usb_ohci0_clk.common.hw,
+		[CLK_USB_PHY0]		= &usb_phy0_clk.common.hw,
+		[CLK_USB_OHCI1]		= &usb_ohci1_clk.common.hw,
+		[CLK_USB_PHY1]		= &usb_phy1_clk.common.hw,
+		[CLK_USB_OHCI2]		= &usb_ohci2_clk.common.hw,
+		[CLK_USB_PHY2]		= &usb_phy2_clk.common.hw,
+		[CLK_USB_OHCI3]		= &usb_ohci3_clk.common.hw,
+		[CLK_USB_PHY3]		= &usb_phy3_clk.common.hw,
+		[CLK_BUS_OHCI0]		= &bus_ohci0_clk.common.hw,
+		[CLK_BUS_OHCI1]		= &bus_ohci1_clk.common.hw,
+		[CLK_BUS_OHCI2]		= &bus_ohci2_clk.common.hw,
+		[CLK_BUS_OHCI3]		= &bus_ohci3_clk.common.hw,
+		[CLK_BUS_EHCI0]		= &bus_ehci0_clk.common.hw,
+		[CLK_BUS_EHCI1]		= &bus_ehci1_clk.common.hw,
+		[CLK_BUS_EHCI2]		= &bus_ehci2_clk.common.hw,
+		[CLK_BUS_EHCI3]		= &bus_ehci3_clk.common.hw,
+		[CLK_BUS_OTG]		= &bus_otg_clk.common.hw,
+		[CLK_BUS_KEYADC]	= &bus_keyadc_clk.common.hw,
+		[CLK_HDMI]		= &hdmi_clk.common.hw,
+		[CLK_HDMI_SLOW]		= &hdmi_slow_clk.common.hw,
+		[CLK_HDMI_CEC]		= &hdmi_cec_clk.common.hw,
+		[CLK_BUS_HDMI]		= &bus_hdmi_clk.common.hw,
+		[CLK_BUS_TCON_TOP]	= &bus_tcon_top_clk.common.hw,
+		[CLK_TCON_TV0]		= &tcon_tv0_clk.common.hw,
+		[CLK_TCON_TV1]		= &tcon_tv1_clk.common.hw,
+		[CLK_BUS_TCON_TV0]	= &bus_tcon_tv0_clk.common.hw,
+		[CLK_BUS_TCON_TV1]	= &bus_tcon_tv1_clk.common.hw,
+		[CLK_TVE0]		= &tve0_clk.common.hw,
+		[CLK_BUS_TVE_TOP]	= &bus_tve_top_clk.common.hw,
+		[CLK_BUS_TVE0]		= &bus_tve0_clk.common.hw,
+		[CLK_HDCP]		= &hdcp_clk.common.hw,
+		[CLK_BUS_HDCP]		= &bus_hdcp_clk.common.hw,
+	},
+	.num = CLK_NUMBER,
+};
+
+static struct ccu_reset_map sun50i_h616_ccu_resets[] = {
+	[RST_MBUS]		= { 0x540, BIT(30) },
+
+	[RST_BUS_DE]		= { 0x60c, BIT(16) },
+	[RST_BUS_DEINTERLACE]	= { 0x62c, BIT(16) },
+	[RST_BUS_GPU]		= { 0x67c, BIT(16) },
+	[RST_BUS_CE]		= { 0x68c, BIT(16) },
+	[RST_BUS_VE]		= { 0x69c, BIT(16) },
+	[RST_BUS_DMA]		= { 0x70c, BIT(16) },
+	[RST_BUS_HSTIMER]	= { 0x73c, BIT(16) },
+	[RST_BUS_DBG]		= { 0x78c, BIT(16) },
+	[RST_BUS_PSI]		= { 0x79c, BIT(16) },
+	[RST_BUS_PWM]		= { 0x7ac, BIT(16) },
+	[RST_BUS_IOMMU]		= { 0x7bc, BIT(16) },
+	[RST_BUS_DRAM]		= { 0x80c, BIT(16) },
+	[RST_BUS_NAND]		= { 0x82c, BIT(16) },
+	[RST_BUS_MMC0]		= { 0x84c, BIT(16) },
+	[RST_BUS_MMC1]		= { 0x84c, BIT(17) },
+	[RST_BUS_MMC2]		= { 0x84c, BIT(18) },
+	[RST_BUS_UART0]		= { 0x90c, BIT(16) },
+	[RST_BUS_UART1]		= { 0x90c, BIT(17) },
+	[RST_BUS_UART2]		= { 0x90c, BIT(18) },
+	[RST_BUS_UART3]		= { 0x90c, BIT(19) },
+	[RST_BUS_UART4]		= { 0x90c, BIT(20) },
+	[RST_BUS_UART5]		= { 0x90c, BIT(21) },
+	[RST_BUS_I2C0]		= { 0x91c, BIT(16) },
+	[RST_BUS_I2C1]		= { 0x91c, BIT(17) },
+	[RST_BUS_I2C2]		= { 0x91c, BIT(18) },
+	[RST_BUS_I2C3]		= { 0x91c, BIT(19) },
+	[RST_BUS_I2C4]		= { 0x91c, BIT(20) },
+	[RST_BUS_SPI0]		= { 0x96c, BIT(16) },
+	[RST_BUS_SPI1]		= { 0x96c, BIT(17) },
+	[RST_BUS_EMAC0]		= { 0x97c, BIT(16) },
+	[RST_BUS_EMAC1]		= { 0x97c, BIT(17) },
+	[RST_BUS_TS]		= { 0x9bc, BIT(16) },
+	[RST_BUS_THS]		= { 0x9fc, BIT(16) },
+	[RST_BUS_SPDIF]		= { 0xa2c, BIT(16) },
+	[RST_BUS_DMIC]		= { 0xa4c, BIT(16) },
+	[RST_BUS_AUDIO_CODEC]	= { 0xa5c, BIT(16) },
+	[RST_BUS_AUDIO_HUB]	= { 0xa6c, BIT(16) },
+
+	[RST_USB_PHY0]		= { 0xa70, BIT(30) },
+	[RST_USB_PHY1]		= { 0xa74, BIT(30) },
+	[RST_USB_PHY2]		= { 0xa78, BIT(30) },
+	[RST_USB_PHY3]		= { 0xa7c, BIT(30) },
+	[RST_BUS_OHCI0]		= { 0xa8c, BIT(16) },
+	[RST_BUS_OHCI1]		= { 0xa8c, BIT(17) },
+	[RST_BUS_OHCI2]		= { 0xa8c, BIT(18) },
+	[RST_BUS_OHCI3]		= { 0xa8c, BIT(19) },
+	[RST_BUS_EHCI0]		= { 0xa8c, BIT(20) },
+	[RST_BUS_EHCI1]		= { 0xa8c, BIT(21) },
+	[RST_BUS_EHCI2]		= { 0xa8c, BIT(22) },
+	[RST_BUS_EHCI3]		= { 0xa8c, BIT(23) },
+	[RST_BUS_OTG]		= { 0xa8c, BIT(24) },
+	[RST_BUS_KEYADC]	= { 0xa9c, BIT(16) },
+
+	[RST_BUS_HDMI]		= { 0xb1c, BIT(16) },
+	[RST_BUS_HDMI_SUB]	= { 0xb1c, BIT(17) },
+	[RST_BUS_TCON_TOP]	= { 0xb5c, BIT(16) },
+	[RST_BUS_TCON_TV0]	= { 0xb9c, BIT(16) },
+	[RST_BUS_TCON_TV1]	= { 0xb9c, BIT(17) },
+	[RST_BUS_TVE_TOP]	= { 0xbbc, BIT(16) },
+	[RST_BUS_TVE0]		= { 0xbbc, BIT(17) },
+	[RST_BUS_HDCP]		= { 0xc4c, BIT(16) },
+};
+
+static const struct sunxi_ccu_desc sun50i_h616_ccu_desc = {
+	.ccu_clks	= sun50i_h616_ccu_clks,
+	.num_ccu_clks	= ARRAY_SIZE(sun50i_h616_ccu_clks),
+
+	.hw_clks	= &sun50i_h616_hw_clks,
+
+	.resets		= sun50i_h616_ccu_resets,
+	.num_resets	= ARRAY_SIZE(sun50i_h616_ccu_resets),
+};
+
+static const u32 pll_regs[] = {
+	SUN50I_H616_PLL_CPUX_REG,
+	SUN50I_H616_PLL_DDR0_REG,
+	SUN50I_H616_PLL_DDR1_REG,
+	SUN50I_H616_PLL_PERIPH0_REG,
+	SUN50I_H616_PLL_PERIPH1_REG,
+	SUN50I_H616_PLL_GPU_REG,
+	SUN50I_H616_PLL_VIDEO0_REG,
+	SUN50I_H616_PLL_VIDEO1_REG,
+	SUN50I_H616_PLL_VIDEO2_REG,
+	SUN50I_H616_PLL_VE_REG,
+	SUN50I_H616_PLL_DE_REG,
+	SUN50I_H616_PLL_AUDIO_REG,
+};
+
+static const u32 pll_video_regs[] = {
+	SUN50I_H616_PLL_VIDEO0_REG,
+	SUN50I_H616_PLL_VIDEO1_REG,
+	SUN50I_H616_PLL_VIDEO2_REG,
+};
+
+static const u32 usb2_clk_regs[] = {
+	SUN50I_H616_USB0_CLK_REG,
+	SUN50I_H616_USB1_CLK_REG,
+	SUN50I_H616_USB2_CLK_REG,
+	SUN50I_H616_USB3_CLK_REG,
+};
+
+static void __init sun50i_h616_ccu_setup(struct device_node *node)
+{
+	void __iomem *reg;
+	u32 val;
+	int i;
+
+	reg = of_io_request_and_map(node, 0, of_node_full_name(node));
+	if (IS_ERR(reg)) {
+		pr_err("%pOF: Could not map clock registers\n", node);
+		return;
+	}
+
+	/* Enable the lock bits and the output enable bits on all PLLs */
+	for (i = 0; i < ARRAY_SIZE(pll_regs); i++) {
+		val = readl(reg + pll_regs[i]);
+		val |= BIT(29) | BIT(27);
+		writel(val, reg + pll_regs[i]);
+	}
+
+	/*
+	 * Force the output divider of video PLLs to 0.
+	 *
+	 * See the comment before pll-video0 definition for the reason.
+	 */
+	for (i = 0; i < ARRAY_SIZE(pll_video_regs); i++) {
+		val = readl(reg + pll_video_regs[i]);
+		val &= ~BIT(0);
+		writel(val, reg + pll_video_regs[i]);
+	}
+
+	/*
+	 * Force OHCI 12M clock sources to 00 (12MHz divided from 48MHz)
+	 *
+	 * This clock mux is still mysterious, and the code just enforces
+	 * it to have a valid clock parent.
+	 */
+	for (i = 0; i < ARRAY_SIZE(usb2_clk_regs); i++) {
+		val = readl(reg + usb2_clk_regs[i]);
+		val &= ~GENMASK(25, 24);
+		writel(val, reg + usb2_clk_regs[i]);
+	}
+
+	/*
+	 * Force the post-divider of pll-audio to 12 and the output divider
+	 * of it to 2, so 24576000 and 22579200 rates can be set exactly.
+	 */
+	val = readl(reg + SUN50I_H616_PLL_AUDIO_REG);
+	val &= ~(GENMASK(21, 16) | BIT(0));
+	writel(val | (11 << 16) | BIT(0), reg + SUN50I_H616_PLL_AUDIO_REG);
+
+	/*
+	 * First clock parent (osc32K) is unusable for CEC. But since there
+	 * is no good way to force parent switch (both run with same frequency),
+	 * just set second clock parent here.
+	 */
+	val = readl(reg + SUN50I_H616_HDMI_CEC_CLK_REG);
+	val |= BIT(24);
+	writel(val, reg + SUN50I_H616_HDMI_CEC_CLK_REG);
+
+	i = sunxi_ccu_probe(node, reg, &sun50i_h616_ccu_desc);
+	if (i)
+		pr_err("%pOF: probing clocks fails: %d\n", node, i);
+}
+
+CLK_OF_DECLARE(sun50i_h616_ccu, "allwinner,sun50i-h616-ccu",
+	       sun50i_h616_ccu_setup);
diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-h616.h b/drivers/clk/sunxi-ng/ccu-sun50i-h616.h
new file mode 100644
index 000000000000..dd671b413f22
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu-sun50i-h616.h
@@ -0,0 +1,56 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright 2020 Arm Ltd.
+ */
+
+#ifndef _CCU_SUN50I_H616_H_
+#define _CCU_SUN50I_H616_H_
+
+#include <dt-bindings/clock/sun50i-h616-ccu.h>
+#include <dt-bindings/reset/sun50i-h616-ccu.h>
+
+#define CLK_OSC12M		0
+#define CLK_PLL_CPUX		1
+#define CLK_PLL_DDR0		2
+#define CLK_PLL_DDR1		3
+
+/* PLL_PERIPH0 exported for PRCM */
+
+#define CLK_PLL_PERIPH0_2X	5
+#define CLK_PLL_PERIPH1		6
+#define CLK_PLL_PERIPH1_2X	7
+#define CLK_PLL_GPU		8
+#define CLK_PLL_VIDEO0		9
+#define CLK_PLL_VIDEO0_4X	10
+#define CLK_PLL_VIDEO1		11
+#define CLK_PLL_VIDEO1_4X	12
+#define CLK_PLL_VIDEO2		13
+#define CLK_PLL_VIDEO2_4X	14
+#define CLK_PLL_VE		15
+#define CLK_PLL_DE		16
+#define CLK_PLL_AUDIO_HS	17
+#define CLK_PLL_AUDIO_1X	18
+#define CLK_PLL_AUDIO_2X	19
+#define CLK_PLL_AUDIO_4X	20
+
+/* CPUX clock exported for DVFS */
+
+#define CLK_AXI			22
+#define CLK_CPUX_APB		23
+#define CLK_PSI_AHB1_AHB2	24
+#define CLK_AHB3		25
+
+/* APB1 clock exported for PIO */
+
+#define CLK_APB2		27
+#define CLK_MBUS		28
+
+/* All module clocks and bus gates are exported except DRAM */
+
+#define CLK_DRAM		49
+
+#define CLK_BUS_DRAM		56
+
+#define CLK_NUMBER		(CLK_BUS_HDCP + 1)
+
+#endif /* _CCU_SUN50I_H616_H_ */
diff --git a/include/dt-bindings/clock/sun50i-h616-ccu.h b/include/dt-bindings/clock/sun50i-h616-ccu.h
new file mode 100644
index 000000000000..4fc08b0df2f3
--- /dev/null
+++ b/include/dt-bindings/clock/sun50i-h616-ccu.h
@@ -0,0 +1,115 @@
+/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */
+/*
+ * Copyright (C) 2020 Arm Ltd.
+ */
+
+#ifndef _DT_BINDINGS_CLK_SUN50I_H616_H_
+#define _DT_BINDINGS_CLK_SUN50I_H616_H_
+
+#define CLK_PLL_PERIPH0		4
+
+#define CLK_CPUX		21
+
+#define CLK_APB1		26
+
+#define CLK_DE			29
+#define CLK_BUS_DE		30
+#define CLK_DEINTERLACE		31
+#define CLK_BUS_DEINTERLACE	32
+#define CLK_G2D			33
+#define CLK_BUS_G2D		34
+#define CLK_GPU0		35
+#define CLK_BUS_GPU		36
+#define CLK_GPU1		37
+#define CLK_CE			38
+#define CLK_BUS_CE		39
+#define CLK_VE			40
+#define CLK_BUS_VE		41
+#define CLK_BUS_DMA		42
+#define CLK_BUS_HSTIMER		43
+#define CLK_AVS			44
+#define CLK_BUS_DBG		45
+#define CLK_BUS_PSI		46
+#define CLK_BUS_PWM		47
+#define CLK_BUS_IOMMU		48
+
+#define CLK_MBUS_DMA		50
+#define CLK_MBUS_VE		51
+#define CLK_MBUS_CE		52
+#define CLK_MBUS_TS		53
+#define CLK_MBUS_NAND		54
+#define CLK_MBUS_G2D		55
+
+#define CLK_NAND0		57
+#define CLK_NAND1		58
+#define CLK_BUS_NAND		59
+#define CLK_MMC0		60
+#define CLK_MMC1		61
+#define CLK_MMC2		62
+#define CLK_BUS_MMC0		63
+#define CLK_BUS_MMC1		64
+#define CLK_BUS_MMC2		65
+#define CLK_BUS_UART0		66
+#define CLK_BUS_UART1		67
+#define CLK_BUS_UART2		68
+#define CLK_BUS_UART3		69
+#define CLK_BUS_UART4		70
+#define CLK_BUS_UART5		71
+#define CLK_BUS_I2C0		72
+#define CLK_BUS_I2C1		73
+#define CLK_BUS_I2C2		74
+#define CLK_BUS_I2C3		75
+#define CLK_BUS_I2C4		76
+#define CLK_SPI0		77
+#define CLK_SPI1		78
+#define CLK_BUS_SPI0		79
+#define CLK_BUS_SPI1		80
+#define CLK_EMAC_25M		81
+#define CLK_BUS_EMAC0		82
+#define CLK_BUS_EMAC1		83
+#define CLK_TS			84
+#define CLK_BUS_TS		85
+#define CLK_BUS_THS		86
+#define CLK_SPDIF		87
+#define CLK_BUS_SPDIF		88
+#define CLK_DMIC		89
+#define CLK_BUS_DMIC		90
+#define CLK_AUDIO_CODEC_1X	91
+#define CLK_AUDIO_CODEC_4X	92
+#define CLK_BUS_AUDIO_CODEC	93
+#define CLK_AUDIO_HUB		94
+#define CLK_BUS_AUDIO_HUB	95
+#define CLK_USB_OHCI0		96
+#define CLK_USB_PHY0		97
+#define CLK_USB_OHCI1		98
+#define CLK_USB_PHY1		99
+#define CLK_USB_OHCI2		100
+#define CLK_USB_PHY2		101
+#define CLK_USB_OHCI3		102
+#define CLK_USB_PHY3		103
+#define CLK_BUS_OHCI0		104
+#define CLK_BUS_OHCI1		105
+#define CLK_BUS_OHCI2		106
+#define CLK_BUS_OHCI3		107
+#define CLK_BUS_EHCI0		108
+#define CLK_BUS_EHCI1		109
+#define CLK_BUS_EHCI2		110
+#define CLK_BUS_EHCI3		111
+#define CLK_BUS_OTG		112
+#define CLK_BUS_KEYADC		113
+#define CLK_HDMI		114
+#define CLK_HDMI_SLOW		115
+#define CLK_HDMI_CEC		116
+#define CLK_BUS_HDMI		117
+#define CLK_BUS_TCON_TOP	118
+#define CLK_TCON_TV0		119
+#define CLK_TCON_TV1		120
+#define CLK_BUS_TCON_TV0	121
+#define CLK_BUS_TCON_TV1	122
+#define CLK_TVE0		123
+#define CLK_BUS_TVE_TOP		124
+#define CLK_BUS_TVE0		125
+#define CLK_HDCP		126
+#define CLK_BUS_HDCP		127
+
+#endif /* _DT_BINDINGS_CLK_SUN50I_H616_H_ */
diff --git a/include/dt-bindings/reset/sun50i-h616-ccu.h b/include/dt-bindings/reset/sun50i-h616-ccu.h
new file mode 100644
index 000000000000..cb6285a8d128
--- /dev/null
+++ b/include/dt-bindings/reset/sun50i-h616-ccu.h
@@ -0,0 +1,70 @@
+/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */
+/*
+ * Copyright (C) 2020 Arm Ltd.
+ */
+
+#ifndef _DT_BINDINGS_RESET_SUN50I_H616_H_
+#define _DT_BINDINGS_RESET_SUN50I_H616_H_
+
+#define RST_MBUS		0
+#define RST_BUS_DE		1
+#define RST_BUS_DEINTERLACE	2
+#define RST_BUS_GPU		3
+#define RST_BUS_CE		4
+#define RST_BUS_VE		5
+#define RST_BUS_DMA		6
+#define RST_BUS_HSTIMER		7
+#define RST_BUS_DBG		8
+#define RST_BUS_PSI		9
+#define RST_BUS_PWM		10
+#define RST_BUS_IOMMU		11
+#define RST_BUS_DRAM		12
+#define RST_BUS_NAND		13
+#define RST_BUS_MMC0		14
+#define RST_BUS_MMC1		15
+#define RST_BUS_MMC2		16
+#define RST_BUS_UART0		17
+#define RST_BUS_UART1		18
+#define RST_BUS_UART2		19
+#define RST_BUS_UART3		20
+#define RST_BUS_UART4		21
+#define RST_BUS_UART5		22
+#define RST_BUS_I2C0		23
+#define RST_BUS_I2C1		24
+#define RST_BUS_I2C2		25
+#define RST_BUS_I2C3		26
+#define RST_BUS_I2C4		27
+#define RST_BUS_SPI0		28
+#define RST_BUS_SPI1		29
+#define RST_BUS_EMAC0		30
+#define RST_BUS_EMAC1		31
+#define RST_BUS_TS		32
+#define RST_BUS_THS		33
+#define RST_BUS_SPDIF		34
+#define RST_BUS_DMIC		35
+#define RST_BUS_AUDIO_CODEC	36
+#define RST_BUS_AUDIO_HUB	37
+#define RST_USB_PHY0		38
+#define RST_USB_PHY1		39
+#define RST_USB_PHY2		40
+#define RST_USB_PHY3		41
+#define RST_BUS_OHCI0		42
+#define RST_BUS_OHCI1		43
+#define RST_BUS_OHCI2		44
+#define RST_BUS_OHCI3		45
+#define RST_BUS_EHCI0		46
+#define RST_BUS_EHCI1		47
+#define RST_BUS_EHCI2		48
+#define RST_BUS_EHCI3		49
+#define RST_BUS_OTG		50
+#define RST_BUS_HDMI		51
+#define RST_BUS_HDMI_SUB	52
+#define RST_BUS_TCON_TOP	53
+#define RST_BUS_TCON_TV0	54
+#define RST_BUS_TCON_TV1	55
+#define RST_BUS_TVE_TOP		56
+#define RST_BUS_TVE0		57
+#define RST_BUS_HDCP		58
+#define RST_BUS_KEYADC		59
+
+#endif /* _DT_BINDINGS_RESET_SUN50I_H616_H_ */
-- 
2.17.5


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 04/20] dt-bindings: mfd: axp20x: Add AXP305 compatible (plus optional IRQ)

[Andre Przywara]

The AXP305 PMIC used in AXP805 seems to be fully compatible to the
AXP805 PMIC, so add the proper chain of compatible strings.

Also at least on one board (Orangepi Zero2) there is no interrupt line
connected to the CPU, so make the "interrupts" property optional.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
 Documentation/devicetree/bindings/mfd/axp20x.txt | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/mfd/axp20x.txt b/Documentation/devicetree/bindings/mfd/axp20x.txt
index 4991a6415796..4fd748101e3c 100644
--- a/Documentation/devicetree/bindings/mfd/axp20x.txt
+++ b/Documentation/devicetree/bindings/mfd/axp20x.txt
@@ -26,10 +26,10 @@ Required properties:
     * "x-powers,axp803"
     * "x-powers,axp806"
     * "x-powers,axp805", "x-powers,axp806"
+    * "x-powers,axp803", "x-powers,axp805", "x-powers,axp806"
     * "x-powers,axp809"
     * "x-powers,axp813"
 - reg: The I2C slave address or RSB hardware address for the AXP chip
-- interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin
 - interrupt-controller: The PMIC has its own internal IRQs
 - #interrupt-cells: Should be set to 1
 
@@ -43,6 +43,7 @@ more information:
 			AXP20x/LDO3: software-based implementation
 
 Optional properties:
+- interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin
 - x-powers,dcdc-freq: defines the work frequency of DC-DC in KHz
 		      AXP152/20X: range:  750-1875, Default: 1.5 MHz
 		      AXP22X/8XX: range: 1800-4050, Default: 3   MHz
-- 
2.17.5


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 05/20] Input: axp20x-pek: Bail out if AXP has no interrupt line connected

[Andre Przywara]

On at least one board (Orangepi Zero2) the AXP305 PMIC does not have its
interrupt line connected to the CPU (mostly because the H616 SoC does
not feature an NMI pin anymore).
After allowing the AXP driver to proceed without an "interrupts"
property [1], the axp20x-pek driver crashes with a NULL pointer
dereference (see below).

Check for the regmap_irqc member to be not NULL before proceeding with
probe. This gets normally filled by the call to regmap_add_irq_chip(),
which we allow to skip now, when the DT node lacks an interrupt
property.

....
[    3.843388] sunxi-rsb 7083000.rsb: RSB running at 3000000 Hz
[    3.849972] axp20x-rsb sunxi-rsb-745: AXP20x variant AXP806 found
[    3.857971] Unable to handle kernel NULL pointer dereference at
virtual address 00000000000001b8
[    3.866855] Mem abort info:
[    3.869691]   ESR = 0x96000004
[    3.872749]   EC = 0x25: DABT (current EL), IL = 32 bits
[    3.878092]   SET = 0, FnV = 0
[    3.881149]   EA = 0, S1PTW = 0
[    3.884309] Data abort info:
[    3.887210]   ISV = 0, ISS = 0x00000004
[    3.891062]   CM = 0, WnR = 0
[    3.894049] [00000000000001b8] user address but active_mm is swapper
[    3.900590] Internal error: Oops: 96000004 [#1] PREEMPT SMP
[    3.906166] Modules linked in:
[    3.909227] CPU: 2 PID: 34 Comm: kworker/2:1 Not tainted 5.11.0-rc1
[    3.915925] Hardware name: OrangePi Zero2 (DT)
[    3.920367] Workqueue: events deferred_probe_work_func
[    3.925518] pstate: 40000005 (nZcv daif -PAN -UAO -TCO BTYPE=--)
[    3.931522] pc : regmap_irq_get_virq+0x0/0x48
[    3.935883] lr : axp20x_pek_probe+0x78/0x200
[    3.940147] sp : ffff800012fdb450
[    3.943459] x29: ffff800012fdb450 x28: ffff0000054af340
[    3.948776] x27: ffff000005534000 x26: ffff000005534810
[    3.954091] x25: ffff800012883028 x24: 0000000000000002
[    3.959407] x23: ffff80001157eaf0 x22: ffff000005534810
[    3.964722] x21: ffff000005534800 x20: ffff0000054b0580
[    3.970037] x19: 000000000000000b x18: 0000000000000000
[    3.975353] x17: 0000000000000001 x16: 0000000000000019
[    3.980668] x15: 000002ce4ea04ae6 x14: 000000000000014f
[    3.985983] x13: 0000000000000282 x12: 0000000000000030
[    3.991298] x11: 0000000000000038 x10: 0101010101010101
[    3.996613] x9 : 0000000000000000 x8 : 7f7f7f7f7f7f7f7f
[    4.001928] x7 : ff5141435e4a444f x6 : 0000000000000080
[    4.007243] x5 : 0000000000000000 x4 : 8000000000000000
[    4.012558] x3 : 0000000000000000 x2 : 0000000000000000
[    4.017872] x1 : 000000000000000b x0 : 0000000000000000
[    4.023188] Call trace:
[    4.025635]  regmap_irq_get_virq+0x0/0x48
[    4.029646]  platform_probe+0x68/0xd8
[    4.033312]  really_probe+0xe4/0x3b0
[    4.036889]  driver_probe_device+0x58/0xb8
[    4.040986]  __device_attach_driver+0x84/0xc8
[    4.045342]  bus_for_each_drv+0x78/0xc8
[    4.049178]  __device_attach+0xf0/0x150
[    4.053013]  device_initial_probe+0x14/0x20
[    4.057196]  bus_probe_device+0x9c/0xa8
[    4.061032]  device_add+0x36c/0x7b8
[    4.064525]  platform_device_add+0x100/0x238
[    4.068796]  mfd_add_devices+0x494/0x718
[    4.072721]  axp20x_device_probe+0x70/0x158
[    4.076904]  axp20x_rsb_probe+0x94/0xd0
[    4.080741]  sunxi_rsb_device_probe+0x6c/0x88
[    4.085102]  really_probe+0xe4/0x3b0
[    4.088679]  driver_probe_device+0x58/0xb8
[    4.092776]  __device_attach_driver+0x84/0xc8
[    4.097132]  bus_for_each_drv+0x78/0xc8
[    4.100967]  __device_attach+0xf0/0x150
[    4.104803]  device_initial_probe+0x14/0x20
[    4.108986]  bus_probe_device+0x9c/0xa8
[    4.112821]  device_add+0x36c/0x7b8
[    4.116313]  device_register+0x20/0x30
[    4.120065]  sunxi_rsb_probe+0x4e4/0x608
....

[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2021-January/633392.html

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
 drivers/input/misc/axp20x-pek.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/input/misc/axp20x-pek.c b/drivers/input/misc/axp20x-pek.c
index 9c6386b2af33..abe52ef194ee 100644
--- a/drivers/input/misc/axp20x-pek.c
+++ b/drivers/input/misc/axp20x-pek.c
@@ -309,6 +309,10 @@ static int axp20x_pek_probe(struct platform_device *pdev)
 
 	axp20x_pek->axp20x = dev_get_drvdata(pdev->dev.parent);
 
+	/* In case there is no interrupt line from the AXP towards the CPU. */
+	if (!axp20x_pek->axp20x->regmap_irqc)
+		return -ENODEV;
+
 	axp20x_pek->irq_dbr = platform_get_irq_byname(pdev, "PEK_DBR");
 	if (axp20x_pek->irq_dbr < 0)
 		return axp20x_pek->irq_dbr;
-- 
2.17.5


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 06/20] mfd: axp20x: Allow AXP chips without interrupt lines

[Andre Przywara]

Currently the AXP chip requires to have its IRQ line connected to some
interrupt controller, and will fail probing when this is not the case.

On a new Allwinner SoC (H616) there is no NMI pin anymore, and at
least one board does not connect the AXP's IRQ pin to anything else,
so the interrupt functionality of the AXP chip is simply not available.

Check whether the interrupt line number returned by the platform code is
valid, before trying to register the irqchip. If not, we skip this
registration, to avoid the driver to bail out completely.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
 drivers/mfd/axp20x.c | 17 +++++++++++------
 1 file changed, 11 insertions(+), 6 deletions(-)

diff --git a/drivers/mfd/axp20x.c b/drivers/mfd/axp20x.c
index 3eae04e24ac8..00c163a1e20d 100644
--- a/drivers/mfd/axp20x.c
+++ b/drivers/mfd/axp20x.c
@@ -959,12 +959,17 @@ int axp20x_device_probe(struct axp20x_dev *axp20x)
 				     AXP806_REG_ADDR_EXT_ADDR_SLAVE_MODE);
 	}
 
-	ret = regmap_add_irq_chip(axp20x->regmap, axp20x->irq,
-			  IRQF_ONESHOT | IRQF_SHARED | axp20x->irq_flags,
-			   -1, axp20x->regmap_irq_chip, &axp20x->regmap_irqc);
-	if (ret) {
-		dev_err(axp20x->dev, "failed to add irq chip: %d\n", ret);
-		return ret;
+	/* Only if there is an interrupt line connected towards the CPU. */
+	if (axp20x->irq > 0) {
+		ret = regmap_add_irq_chip(axp20x->regmap, axp20x->irq,
+				IRQF_ONESHOT | IRQF_SHARED | axp20x->irq_flags,
+				-1, axp20x->regmap_irq_chip,
+				&axp20x->regmap_irqc);
+		if (ret) {
+			dev_err(axp20x->dev, "failed to add irq chip: %d\n",
+				ret);
+			return ret;
+		}
 	}
 
 	ret = mfd_add_devices(axp20x->dev, -1, axp20x->cells,
-- 
2.17.5


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 07/20] dt-bindings: sram: sunxi-sram: Add H616 compatible string

[Andre Przywara]

The H616 adds a second EMAC clock register. We don't know about the
exact SRAM properties yet, so this gets omitted for now.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
---
 .../bindings/sram/allwinner,sun4i-a10-system-control.yaml        | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/sram/allwinner,sun4i-a10-system-control.yaml b/Documentation/devicetree/bindings/sram/allwinner,sun4i-a10-system-control.yaml
index b66a07e21d1e..1c426c211e36 100644
--- a/Documentation/devicetree/bindings/sram/allwinner,sun4i-a10-system-control.yaml
+++ b/Documentation/devicetree/bindings/sram/allwinner,sun4i-a10-system-control.yaml
@@ -49,6 +49,7 @@ properties:
       - items:
           - const: allwinner,suniv-f1c100s-system-control
           - const: allwinner,sun4i-a10-system-control
+      - const: allwinner,sun50i-h616-system-control
 
   reg:
     maxItems: 1
-- 
2.17.5


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 08/20] soc: sunxi: sram: Add support for more than one EMAC clock

[Andre Przywara]

The Allwinner H616 adds a second EMAC clock register at offset 0x34, for
controlling the second EMAC in this chip.

Allow to extend the regmap in this case, to cover more than the current
4 bytes exported.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
 drivers/soc/sunxi/sunxi_sram.c | 31 +++++++++++++++++++++++--------
 1 file changed, 23 insertions(+), 8 deletions(-)

diff --git a/drivers/soc/sunxi/sunxi_sram.c b/drivers/soc/sunxi/sunxi_sram.c
index d4c7bd59429e..42833e33a96c 100644
--- a/drivers/soc/sunxi/sunxi_sram.c
+++ b/drivers/soc/sunxi/sunxi_sram.c
@@ -283,7 +283,7 @@ int sunxi_sram_release(struct device *dev)
 EXPORT_SYMBOL(sunxi_sram_release);
 
 struct sunxi_sramc_variant {
-	bool has_emac_clock;
+	int num_emac_clocks;
 };
 
 static const struct sunxi_sramc_variant sun4i_a10_sramc_variant = {
@@ -291,20 +291,31 @@ static const struct sunxi_sramc_variant sun4i_a10_sramc_variant = {
 };
 
 static const struct sunxi_sramc_variant sun8i_h3_sramc_variant = {
-	.has_emac_clock = true,
+	.num_emac_clocks = 1,
 };
 
 static const struct sunxi_sramc_variant sun50i_a64_sramc_variant = {
-	.has_emac_clock = true,
+	.num_emac_clocks = 1,
+};
+
+static const struct sunxi_sramc_variant sun50i_h616_sramc_variant = {
+	.num_emac_clocks = 2,
 };
 
 #define SUNXI_SRAM_EMAC_CLOCK_REG	0x30
 static bool sunxi_sram_regmap_accessible_reg(struct device *dev,
 					     unsigned int reg)
 {
-	if (reg == SUNXI_SRAM_EMAC_CLOCK_REG)
-		return true;
-	return false;
+	const struct sunxi_sramc_variant *variant;
+
+	variant = of_device_get_match_data(dev);
+
+	if (reg < SUNXI_SRAM_EMAC_CLOCK_REG)
+		return false;
+	if (reg > SUNXI_SRAM_EMAC_CLOCK_REG + variant->num_emac_clocks * 4)
+		return false;
+
+	return true;
 }
 
 static struct regmap_config sunxi_sram_emac_clock_regmap = {
@@ -312,7 +323,7 @@ static struct regmap_config sunxi_sram_emac_clock_regmap = {
 	.val_bits       = 32,
 	.reg_stride     = 4,
 	/* last defined register */
-	.max_register   = SUNXI_SRAM_EMAC_CLOCK_REG,
+	.max_register   = SUNXI_SRAM_EMAC_CLOCK_REG + 4,
 	/* other devices have no business accessing other registers */
 	.readable_reg	= sunxi_sram_regmap_accessible_reg,
 	.writeable_reg	= sunxi_sram_regmap_accessible_reg,
@@ -343,7 +354,7 @@ static int sunxi_sram_probe(struct platform_device *pdev)
 	if (!d)
 		return -ENOMEM;
 
-	if (variant->has_emac_clock) {
+	if (variant->num_emac_clocks > 0) {
 		emac_clock = devm_regmap_init_mmio(&pdev->dev, base,
 						   &sunxi_sram_emac_clock_regmap);
 
@@ -387,6 +398,10 @@ static const struct of_device_id sunxi_sram_dt_match[] = {
 		.compatible = "allwinner,sun50i-h5-system-control",
 		.data = &sun50i_a64_sramc_variant,
 	},
+	{
+		.compatible = "allwinner,sun50i-h616-system-control",
+		.data = &sun50i_h616_sramc_variant,
+	},
 	{ },
 };
 MODULE_DEVICE_TABLE(of, sunxi_sram_dt_match);
-- 
2.17.5


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 09/20] dt-bindings: watchdog: sun4i: Add H616 compatible string

[Andre Przywara]

Use enums to group all compatible devices together on the way.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
---
 .../bindings/watchdog/allwinner,sun4i-a10-wdt.yaml   | 12 +++++-------
 1 file changed, 5 insertions(+), 7 deletions(-)

diff --git a/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml b/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml
index 5ac607de8be4..9aa3c313c49f 100644
--- a/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml
+++ b/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml
@@ -19,13 +19,11 @@ properties:
       - const: allwinner,sun4i-a10-wdt
       - const: allwinner,sun6i-a31-wdt
       - items:
-          - const: allwinner,sun50i-a64-wdt
-          - const: allwinner,sun6i-a31-wdt
-      - items:
-          - const: allwinner,sun50i-a100-wdt
-          - const: allwinner,sun6i-a31-wdt
-      - items:
-          - const: allwinner,sun50i-h6-wdt
+          - enum:
+              - allwinner,sun50i-a64-wdt
+              - allwinner,sun50i-a100-wdt
+              - allwinner,sun50i-h6-wdt
+              - allwinner,sun50i-h616-wdt
           - const: allwinner,sun6i-a31-wdt
       - items:
           - const: allwinner,suniv-f1c100s-wdt
-- 
2.17.5


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 10/20] dt-bindings: i2c: mv64xxx: Add H616 compatible string

[Andre Przywara]

Add the obvious compatible name to the existing I2C binding, and pair
it with the existing A31 fallback compatible string, as the devices
are compatible.

On the way use enums to group all compatible devices together.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Wolfram Sang <wsa@kernel.org>
---
 .../bindings/i2c/marvell,mv64xxx-i2c.yaml     | 21 +++++++------------
 1 file changed, 7 insertions(+), 14 deletions(-)

diff --git a/Documentation/devicetree/bindings/i2c/marvell,mv64xxx-i2c.yaml b/Documentation/devicetree/bindings/i2c/marvell,mv64xxx-i2c.yaml
index 5b5ae402f97a..eb72dd571def 100644
--- a/Documentation/devicetree/bindings/i2c/marvell,mv64xxx-i2c.yaml
+++ b/Documentation/devicetree/bindings/i2c/marvell,mv64xxx-i2c.yaml
@@ -18,21 +18,14 @@ properties:
           - const: allwinner,sun4i-a10-i2c
       - const: allwinner,sun6i-a31-i2c
       - items:
-          - const: allwinner,sun8i-a23-i2c
+          - enum:
+              - allwinner,sun8i-a23-i2c
+              - allwinner,sun8i-a83t-i2c
+              - allwinner,sun50i-a64-i2c
+              - allwinner,sun50i-a100-i2c
+              - allwinner,sun50i-h6-i2c
+              - allwinner,sun50i-h616-i2c
           - const: allwinner,sun6i-a31-i2c
-      - items:
-          - const: allwinner,sun8i-a83t-i2c
-          - const: allwinner,sun6i-a31-i2c
-      - items:
-          - const: allwinner,sun50i-a64-i2c
-          - const: allwinner,sun6i-a31-i2c
-      - items:
-          - const: allwinner,sun50i-a100-i2c
-          - const: allwinner,sun6i-a31-i2c
-      - items:
-          - const: allwinner,sun50i-h6-i2c
-          - const: allwinner,sun6i-a31-i2c
-
       - const: marvell,mv64xxx-i2c
       - const: marvell,mv78230-i2c
       - const: marvell,mv78230-a0-i2c
-- 
2.17.5


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 11/20] dt-bindings: media: IR: Add H616 IR compatible string

[Andre Przywara]

Add the obvious compatible name to the existing IR binding, and pair
it with the existing A31 fallback compatible string, as the devices
are compatible.

On the way use enums to group all compatible devices together.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
---
 .../bindings/media/allwinner,sun4i-a10-ir.yaml   | 16 ++++++----------
 1 file changed, 6 insertions(+), 10 deletions(-)

diff --git a/Documentation/devicetree/bindings/media/allwinner,sun4i-a10-ir.yaml b/Documentation/devicetree/bindings/media/allwinner,sun4i-a10-ir.yaml
index 5fa19d4aeaf3..6d8395d6bca0 100644
--- a/Documentation/devicetree/bindings/media/allwinner,sun4i-a10-ir.yaml
+++ b/Documentation/devicetree/bindings/media/allwinner,sun4i-a10-ir.yaml
@@ -20,16 +20,12 @@ properties:
       - const: allwinner,sun5i-a13-ir
       - const: allwinner,sun6i-a31-ir
       - items:
-          - const: allwinner,sun8i-a83t-ir
-          - const: allwinner,sun6i-a31-ir
-      - items:
-          - const: allwinner,sun8i-r40-ir
-          - const: allwinner,sun6i-a31-ir
-      - items:
-          - const: allwinner,sun50i-a64-ir
-          - const: allwinner,sun6i-a31-ir
-      - items:
-          - const: allwinner,sun50i-h6-ir
+          - enum:
+              - allwinner,sun8i-a83t-ir
+              - allwinner,sun8i-r40-ir
+              - allwinner,sun50i-a64-ir
+              - allwinner,sun50i-h6-ir
+              - allwinner,sun50i-h616-ir
           - const: allwinner,sun6i-a31-ir
 
   reg:
-- 
2.17.5


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 12/20] dt-bindings: rtc: sun6i: Add H616 compatible string

[Andre Przywara]

Add the obvious compatible name to the existing RTC binding, and pair
it with the existing H6 fallback compatible string, as the devices are
compatible.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
---
 .../devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml       | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml b/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml
index b1b0ee769b71..4193e5813344 100644
--- a/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml
+++ b/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml
@@ -26,6 +26,9 @@ properties:
           - const: allwinner,sun50i-a64-rtc
           - const: allwinner,sun8i-h3-rtc
       - const: allwinner,sun50i-h6-rtc
+      - items:
+          - const: allwinner,sun50i-h616-rtc
+          - const: allwinner,sun50i-h6-rtc
 
   reg:
     maxItems: 1
-- 
2.17.5


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 13/20] dt-bindings: spi: sunxi: Add H616 compatible string

[Andre Przywara]

Add the obvious compatible name to the existing SPI binding, and pair
it with the existing H3 fallback compatible string, as the devices are
compatible.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
---
 .../devicetree/bindings/spi/allwinner,sun6i-a31-spi.yaml         | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/spi/allwinner,sun6i-a31-spi.yaml b/Documentation/devicetree/bindings/spi/allwinner,sun6i-a31-spi.yaml
index 7866a655d81c..908248260afa 100644
--- a/Documentation/devicetree/bindings/spi/allwinner,sun6i-a31-spi.yaml
+++ b/Documentation/devicetree/bindings/spi/allwinner,sun6i-a31-spi.yaml
@@ -25,6 +25,7 @@ properties:
           - enum:
               - allwinner,sun8i-r40-spi
               - allwinner,sun50i-h6-spi
+              - allwinner,sun50i-h616-spi
           - const: allwinner,sun8i-h3-spi
 
   reg:
-- 
2.17.5


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 14/20] dt-bindings: bus: rsb: Add H616 compatible string

[Andre Przywara]

Add the obvious compatible name to the existing RSB binding, and pair
it with the existing A23 fallback compatible string, as the devices are
compatible.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
 .../devicetree/bindings/bus/allwinner,sun8i-a23-rsb.yaml      | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/bus/allwinner,sun8i-a23-rsb.yaml b/Documentation/devicetree/bindings/bus/allwinner,sun8i-a23-rsb.yaml
index 32d33b983d66..3d719f468a5b 100644
--- a/Documentation/devicetree/bindings/bus/allwinner,sun8i-a23-rsb.yaml
+++ b/Documentation/devicetree/bindings/bus/allwinner,sun8i-a23-rsb.yaml
@@ -21,7 +21,9 @@ properties:
     oneOf:
       - const: allwinner,sun8i-a23-rsb
       - items:
-          - const: allwinner,sun8i-a83t-rsb
+          - enum:
+              - allwinner,sun8i-a83t-rsb
+              - allwinner,sun50i-h616-rsb
           - const: allwinner,sun8i-a23-rsb
 
   reg:
-- 
2.17.5


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 15/20] dt-bindings: net: sun8i-emac: Add H616 compatible string

[Andre Przywara]

Add the obvious compatible name to the existing EMAC binding, and pair
it with the existing A64 fallback compatible string, as the devices are
compatible.

On the way use enums to group the compatible devices together.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
 .../devicetree/bindings/net/allwinner,sun8i-a83t-emac.yaml    | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/net/allwinner,sun8i-a83t-emac.yaml b/Documentation/devicetree/bindings/net/allwinner,sun8i-a83t-emac.yaml
index 7f2578d48e3f..0ccdab103f59 100644
--- a/Documentation/devicetree/bindings/net/allwinner,sun8i-a83t-emac.yaml
+++ b/Documentation/devicetree/bindings/net/allwinner,sun8i-a83t-emac.yaml
@@ -19,7 +19,9 @@ properties:
       - const: allwinner,sun8i-v3s-emac
       - const: allwinner,sun50i-a64-emac
       - items:
-          - const: allwinner,sun50i-h6-emac
+          - enum:
+              - allwinner,sun50i-h6-emac
+              - allwinner,sun50i-h616-emac
           - const: allwinner,sun50i-a64-emac
 
   reg:
-- 
2.17.5


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 16/20] net: stmmac: dwmac-sun8i: Prepare for second EMAC clock register

[Andre Przywara]

The Allwinner H616 SoC has two EMAC controllers, with the second one
being tied to the internal PHY, but also using a separate EMAC clock
register.

To tell the driver about which clock register to use, we add a parameter
to our syscon phandle. The driver will use this value as an index into
the regmap, so that we can address more than the first register, if
needed.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
 drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c | 12 ++++++++++--
 1 file changed, 10 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
index 58e0511badba..c7951790ed98 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
@@ -1124,11 +1124,13 @@ static int sun8i_dwmac_probe(struct platform_device *pdev)
 	struct stmmac_resources stmmac_res;
 	struct sunxi_priv_data *gmac;
 	struct device *dev = &pdev->dev;
+	struct reg_field syscon_field;
 	phy_interface_t interface;
 	int ret;
 	struct stmmac_priv *priv;
 	struct net_device *ndev;
 	struct regmap *regmap;
+	u32 syscon_idx = 0;
 
 	ret = stmmac_get_platform_resources(pdev, &stmmac_res);
 	if (ret)
@@ -1190,8 +1192,12 @@ static int sun8i_dwmac_probe(struct platform_device *pdev)
 		return ret;
 	}
 
-	gmac->regmap_field = devm_regmap_field_alloc(dev, regmap,
-						     *gmac->variant->syscon_field);
+	syscon_field = *gmac->variant->syscon_field;
+	ret = of_property_read_u32_index(pdev->dev.of_node, "syscon", 1,
+					 &syscon_idx);
+	if (!ret)
+		syscon_field.reg += syscon_idx * sizeof(u32);
+	gmac->regmap_field = devm_regmap_field_alloc(dev, regmap, syscon_field);
 	if (IS_ERR(gmac->regmap_field)) {
 		ret = PTR_ERR(gmac->regmap_field);
 		dev_err(dev, "Unable to map syscon register: %d\n", ret);
@@ -1263,6 +1269,8 @@ static const struct of_device_id sun8i_dwmac_match[] = {
 		.data = &emac_variant_a64 },
 	{ .compatible = "allwinner,sun50i-h6-emac",
 		.data = &emac_variant_h6 },
+	{ .compatible = "allwinner,sun50i-h616-emac",
+		.data = &emac_variant_h6 },
 	{ }
 };
 MODULE_DEVICE_TABLE(of, sun8i_dwmac_match);
-- 
2.17.5


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 17/20] phy: sun4i-usb: Rework HCI PHY (aka. "pmu_unk1") handling

[Andre Przywara]

As Icenowy pointed out, newer manuals (starting with H6) actually
document the register block at offset 0x800 as "HCI controller and PHY
interface", also describe the bits in our "PMU_UNK1" register.
Let's put proper names to those "unknown" variables and symbols.

While we are at it, generalise the existing code by allowing a bitmap
of bits to clear, to cover newer SoCs: The A100 and H616 use a different
bit for the SIDDQ control.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
---
 drivers/phy/allwinner/phy-sun4i-usb.c | 29 +++++++++++----------------
 1 file changed, 12 insertions(+), 17 deletions(-)

diff --git a/drivers/phy/allwinner/phy-sun4i-usb.c b/drivers/phy/allwinner/phy-sun4i-usb.c
index 788dd5cdbb7d..539209fe3468 100644
--- a/drivers/phy/allwinner/phy-sun4i-usb.c
+++ b/drivers/phy/allwinner/phy-sun4i-usb.c
@@ -43,7 +43,7 @@
 #define REG_PHYCTL_A33			0x10
 #define REG_PHY_OTGCTL			0x20
 
-#define REG_PMU_UNK1			0x10
+#define REG_HCI_PHY_CTL			0x10
 
 #define PHYCTL_DATA			BIT(7)
 
@@ -115,9 +115,9 @@ struct sun4i_usb_phy_cfg {
 	int hsic_index;
 	enum sun4i_usb_phy_type type;
 	u32 disc_thresh;
+	u32 hci_phy_ctl_siddq;
 	u8 phyctl_offset;
 	bool dedicated_clocks;
-	bool enable_pmu_unk1;
 	bool phy0_dual_route;
 	int missing_phys;
 };
@@ -288,6 +288,12 @@ static int sun4i_usb_phy_init(struct phy *_phy)
 		return ret;
 	}
 
+	if (phy->pmu && data->cfg->hci_phy_ctl_siddq) {
+		val = readl(phy->pmu + REG_HCI_PHY_CTL);
+		val &= ~data->cfg->hci_phy_ctl_siddq;
+		writel(val, phy->pmu + REG_HCI_PHY_CTL);
+	}
+
 	if (data->cfg->type == sun8i_a83t_phy ||
 	    data->cfg->type == sun50i_h6_phy) {
 		if (phy->index == 0) {
@@ -297,11 +303,6 @@ static int sun4i_usb_phy_init(struct phy *_phy)
 			writel(val, data->base + data->cfg->phyctl_offset);
 		}
 	} else {
-		if (phy->pmu && data->cfg->enable_pmu_unk1) {
-			val = readl(phy->pmu + REG_PMU_UNK1);
-			writel(val & ~2, phy->pmu + REG_PMU_UNK1);
-		}
-
 		/* Enable USB 45 Ohm resistor calibration */
 		if (phy->index == 0)
 			sun4i_usb_phy_write(phy, PHY_RES45_CAL_EN, 0x01, 1);
@@ -863,7 +864,6 @@ static const struct sun4i_usb_phy_cfg sun4i_a10_cfg = {
 	.disc_thresh = 3,
 	.phyctl_offset = REG_PHYCTL_A10,
 	.dedicated_clocks = false,
-	.enable_pmu_unk1 = false,
 };
 
 static const struct sun4i_usb_phy_cfg sun5i_a13_cfg = {
@@ -872,7 +872,6 @@ static const struct sun4i_usb_phy_cfg sun5i_a13_cfg = {
 	.disc_thresh = 2,
 	.phyctl_offset = REG_PHYCTL_A10,
 	.dedicated_clocks = false,
-	.enable_pmu_unk1 = false,
 };
 
 static const struct sun4i_usb_phy_cfg sun6i_a31_cfg = {
@@ -881,7 +880,6 @@ static const struct sun4i_usb_phy_cfg sun6i_a31_cfg = {
 	.disc_thresh = 3,
 	.phyctl_offset = REG_PHYCTL_A10,
 	.dedicated_clocks = true,
-	.enable_pmu_unk1 = false,
 };
 
 static const struct sun4i_usb_phy_cfg sun7i_a20_cfg = {
@@ -890,7 +888,6 @@ static const struct sun4i_usb_phy_cfg sun7i_a20_cfg = {
 	.disc_thresh = 2,
 	.phyctl_offset = REG_PHYCTL_A10,
 	.dedicated_clocks = false,
-	.enable_pmu_unk1 = false,
 };
 
 static const struct sun4i_usb_phy_cfg sun8i_a23_cfg = {
@@ -899,7 +896,6 @@ static const struct sun4i_usb_phy_cfg sun8i_a23_cfg = {
 	.disc_thresh = 3,
 	.phyctl_offset = REG_PHYCTL_A10,
 	.dedicated_clocks = true,
-	.enable_pmu_unk1 = false,
 };
 
 static const struct sun4i_usb_phy_cfg sun8i_a33_cfg = {
@@ -908,7 +904,6 @@ static const struct sun4i_usb_phy_cfg sun8i_a33_cfg = {
 	.disc_thresh = 3,
 	.phyctl_offset = REG_PHYCTL_A33,
 	.dedicated_clocks = true,
-	.enable_pmu_unk1 = false,
 };
 
 static const struct sun4i_usb_phy_cfg sun8i_a83t_cfg = {
@@ -925,7 +920,7 @@ static const struct sun4i_usb_phy_cfg sun8i_h3_cfg = {
 	.disc_thresh = 3,
 	.phyctl_offset = REG_PHYCTL_A33,
 	.dedicated_clocks = true,
-	.enable_pmu_unk1 = true,
+	.hci_phy_ctl_siddq = BIT(1),
 	.phy0_dual_route = true,
 };
 
@@ -935,7 +930,7 @@ static const struct sun4i_usb_phy_cfg sun8i_r40_cfg = {
 	.disc_thresh = 3,
 	.phyctl_offset = REG_PHYCTL_A33,
 	.dedicated_clocks = true,
-	.enable_pmu_unk1 = true,
+	.hci_phy_ctl_siddq = BIT(1),
 	.phy0_dual_route = true,
 };
 
@@ -945,7 +940,7 @@ static const struct sun4i_usb_phy_cfg sun8i_v3s_cfg = {
 	.disc_thresh = 3,
 	.phyctl_offset = REG_PHYCTL_A33,
 	.dedicated_clocks = true,
-	.enable_pmu_unk1 = true,
+	.hci_phy_ctl_siddq = BIT(1),
 	.phy0_dual_route = true,
 };
 
@@ -955,7 +950,7 @@ static const struct sun4i_usb_phy_cfg sun50i_a64_cfg = {
 	.disc_thresh = 3,
 	.phyctl_offset = REG_PHYCTL_A33,
 	.dedicated_clocks = true,
-	.enable_pmu_unk1 = true,
+	.hci_phy_ctl_siddq = BIT(1),
 	.phy0_dual_route = true,
 };
 
-- 
2.17.5


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 18/20] arm64: dts: allwinner: Add Allwinner H616 .dtsi file

[Andre Przywara]

This (relatively) new SoC is similar to the H6, but drops the (broken)
PCIe support and the USB 3.0 controller. It also gets the management
controller removed, which in turn removes *some*, but not all of the
devices formerly dedicated to the ARISC (CPUS).
There does not seem to be an extra interrupt controller anymore, also
it lacks the corresponding NMI pin, so no interrupts for the PMIC.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
 .../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 573 ++++++++++++++++++
 1 file changed, 573 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
new file mode 100644
index 000000000000..c277b53f94ea
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
@@ -0,0 +1,573 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2020 Arm Ltd.
+// based on the H6 dtsi, which is:
+//   Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/sun50i-h616-ccu.h>
+#include <dt-bindings/clock/sun50i-h6-r-ccu.h>
+#include <dt-bindings/reset/sun50i-h616-ccu.h>
+#include <dt-bindings/reset/sun50i-h6-r-ccu.h>
+
+/ {
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			reg = <0>;
+			enable-method = "psci";
+			clocks = <&ccu CLK_CPUX>;
+		};
+
+		cpu1: cpu@1 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			reg = <1>;
+			enable-method = "psci";
+			clocks = <&ccu CLK_CPUX>;
+		};
+
+		cpu2: cpu@2 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			reg = <2>;
+			enable-method = "psci";
+			clocks = <&ccu CLK_CPUX>;
+		};
+
+		cpu3: cpu@3 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			reg = <3>;
+			enable-method = "psci";
+			clocks = <&ccu CLK_CPUX>;
+		};
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/* 512KiB reserved for ARM Trusted Firmware (BL31) */
+		secmon_reserved: secmon@40000000 {
+			reg = <0x0 0x40000000 0x0 0x80000>;
+			no-map;
+		};
+	};
+
+	osc24M: osc24M_clk {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <24000000>;
+		clock-output-names = "osc24M";
+	};
+
+	pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		arm,no-tick-in-suspend;
+		interrupts = <GIC_PPI 13
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 14
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 11
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 10
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0x0 0x40000000>;
+
+		syscon: syscon@3000000 {
+			compatible = "allwinner,sun50i-h616-system-control";
+			reg = <0x03000000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			sram_c: sram@28000 {
+				compatible = "mmio-sram";
+				reg = <0x00028000 0x30000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 0x00028000 0x30000>;
+			};
+		};
+
+		ccu: clock@3001000 {
+			compatible = "allwinner,sun50i-h616-ccu";
+			reg = <0x03001000 0x1000>;
+			clocks = <&osc24M>, <&rtc 0>, <&rtc 2>;
+			clock-names = "hosc", "losc", "iosc";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		watchdog: watchdog@30090a0 {
+			compatible = "allwinner,sun50i-h616-wdt",
+				     "allwinner,sun6i-a31-wdt";
+			reg = <0x030090a0 0x20>;
+			interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&osc24M>;
+			status = "okay";
+		};
+
+		pio: pinctrl@300b000 {
+			compatible = "allwinner,sun50i-h616-pinctrl";
+			reg = <0x0300b000 0x400>;
+			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_APB1>, <&osc24M>, <&rtc 0>;
+			clock-names = "apb", "hosc", "losc";
+			gpio-controller;
+			#gpio-cells = <3>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+
+			ext_rgmii_pins: rgmii-pins {
+				pins = "PI0", "PI1", "PI2", "PI3", "PI4",
+				       "PI5", "PI7", "PI8", "PI9", "PI10",
+				       "PI11", "PI12", "PI13", "PI14", "PI15",
+				       "PI16";
+				function = "emac0";
+				drive-strength = <40>;
+			};
+
+			i2c0_pins: i2c0-pins {
+				pins = "PI6", "PI7";
+				function = "i2c0";
+			};
+
+			i2c3_ph_pins: i2c3-ph-pins {
+				pins = "PH4", "PH5";
+				function = "i2c3";
+			};
+
+			ir_rx_pin: ir-rx-pin {
+				pins = "PH10";
+				function = "ir_rx";
+			};
+
+			mmc0_pins: mmc0-pins {
+				pins = "PF0", "PF1", "PF2", "PF3",
+				       "PF4", "PF5";
+				function = "mmc0";
+				drive-strength = <30>;
+				bias-pull-up;
+			};
+
+			mmc1_pins: mmc1-pins {
+				pins = "PG0", "PG1", "PG2", "PG3",
+				       "PG4", "PG5";
+				function = "mmc1";
+				drive-strength = <30>;
+				bias-pull-up;
+			};
+
+			mmc2_pins: mmc2-pins {
+				pins = "PC0", "PC1", "PC5", "PC6",
+				       "PC8", "PC9", "PC10", "PC11",
+				       "PC13", "PC14", "PC15", "PC16";
+				function = "mmc2";
+				drive-strength = <30>;
+				bias-pull-up;
+			};
+
+			spi0_pins: spi0-pins {
+				pins = "PC0", "PC2", "PC3", "PC4";
+				function = "spi0";
+			};
+
+			spi1_pins: spi1-pins {
+				pins = "PH6", "PH7", "PH8";
+				function = "spi1";
+			};
+
+			spi1_cs_pin: spi1-cs-pin {
+				pins = "PH5";
+				function = "spi1";
+			};
+
+			uart0_ph_pins: uart0-ph-pins {
+				pins = "PH0", "PH1";
+				function = "uart0";
+			};
+
+			uart1_pins: uart1-pins {
+				pins = "PG6", "PG7";
+				function = "uart1";
+			};
+
+			uart1_rts_cts_pins: uart1-rts-cts-pins {
+				pins = "PG8", "PG9";
+				function = "uart1";
+			};
+		};
+
+		gic: interrupt-controller@3021000 {
+			compatible = "arm,gic-400";
+			reg = <0x03021000 0x1000>,
+			      <0x03022000 0x2000>,
+			      <0x03024000 0x2000>,
+			      <0x03026000 0x2000>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+		};
+
+		mmc0: mmc@4020000 {
+			compatible = "allwinner,sun50i-h616-mmc",
+				     "allwinner,sun50i-a100-mmc";
+			reg = <0x04020000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
+			clock-names = "ahb", "mmc";
+			resets = <&ccu RST_BUS_MMC0>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc0_pins>;
+			status = "disabled";
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			mmc-ddr-3_3v;
+			mmc-ddr-1_8v;
+			cap-sdio-irq;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mmc1: mmc@4021000 {
+			compatible = "allwinner,sun50i-h616-mmc",
+				     "allwinner,sun50i-a100-mmc";
+			reg = <0x04021000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
+			clock-names = "ahb", "mmc";
+			resets = <&ccu RST_BUS_MMC1>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc1_pins>;
+			status = "disabled";
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			mmc-ddr-3_3v;
+			mmc-ddr-1_8v;
+			cap-sdio-irq;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mmc2: mmc@4022000 {
+			compatible = "allwinner,sun50i-h616-emmc",
+				     "allwinner,sun50i-a100-emmc";
+			reg = <0x04022000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
+			clock-names = "ahb", "mmc";
+			resets = <&ccu RST_BUS_MMC2>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc2_pins>;
+			status = "disabled";
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			mmc-ddr-3_3v;
+			mmc-ddr-1_8v;
+			cap-sdio-irq;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		uart0: serial@5000000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05000000 0x400>;
+			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART0>;
+			resets = <&ccu RST_BUS_UART0>;
+			status = "disabled";
+		};
+
+		uart1: serial@5000400 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05000400 0x400>;
+			interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART1>;
+			resets = <&ccu RST_BUS_UART1>;
+			status = "disabled";
+		};
+
+		uart2: serial@5000800 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05000800 0x400>;
+			interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART2>;
+			resets = <&ccu RST_BUS_UART2>;
+			status = "disabled";
+		};
+
+		uart3: serial@5000c00 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05000c00 0x400>;
+			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART3>;
+			resets = <&ccu RST_BUS_UART3>;
+			status = "disabled";
+		};
+
+		uart4: serial@5001000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05001000 0x400>;
+			interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART4>;
+			resets = <&ccu RST_BUS_UART4>;
+			status = "disabled";
+		};
+
+		uart5: serial@5001400 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05001400 0x400>;
+			interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART5>;
+			resets = <&ccu RST_BUS_UART5>;
+			status = "disabled";
+		};
+
+		i2c0: i2c@5002000 {
+			compatible = "allwinner,sun50i-h616-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x05002000 0x400>;
+			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C0>;
+			resets = <&ccu RST_BUS_I2C0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c0_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c1: i2c@5002400 {
+			compatible = "allwinner,sun50i-h616-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x05002400 0x400>;
+			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C1>;
+			resets = <&ccu RST_BUS_I2C1>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c2: i2c@5002800 {
+			compatible = "allwinner,sun50i-h616-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x05002800 0x400>;
+			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C2>;
+			resets = <&ccu RST_BUS_I2C2>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c3: i2c@5002c00 {
+			compatible = "allwinner,sun50i-h616-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x05002c00 0x400>;
+			interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C3>;
+			resets = <&ccu RST_BUS_I2C3>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c4: i2c@5003000 {
+			compatible = "allwinner,sun50i-h616-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x05003000 0x400>;
+			interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C4>;
+			resets = <&ccu RST_BUS_I2C4>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		spi0: spi@5010000 {
+			compatible = "allwinner,sun50i-h616-spi",
+				     "allwinner,sun8i-h3-spi";
+			reg = <0x05010000 0x1000>;
+			interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
+			clock-names = "ahb", "mod";
+			resets = <&ccu RST_BUS_SPI0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&spi0_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		spi1: spi@5011000 {
+			compatible = "allwinner,sun50i-h616-spi",
+				     "allwinner,sun8i-h3-spi";
+			reg = <0x05011000 0x1000>;
+			interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
+			clock-names = "ahb", "mod";
+			resets = <&ccu RST_BUS_SPI1>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&spi1_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		emac0: ethernet@5020000 {
+			compatible = "allwinner,sun50i-h616-emac",
+				     "allwinner,sun50i-a64-emac";
+			syscon = <&syscon>;
+			reg = <0x05020000 0x10000>;
+			interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+			resets = <&ccu RST_BUS_EMAC0>;
+			reset-names = "stmmaceth";
+			clocks = <&ccu CLK_BUS_EMAC0>;
+			clock-names = "stmmaceth";
+			status = "disabled";
+
+			mdio0: mdio {
+				compatible = "snps,dwmac-mdio";
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
+		rtc: rtc@7000000 {
+			compatible = "allwinner,sun50i-h616-rtc",
+				     "allwinner,sun50i-h6-rtc";
+			reg = <0x07000000 0x400>;
+			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+			clock-output-names = "osc32k", "osc32k-out", "iosc";
+			#clock-cells = <1>;
+		};
+
+		r_ccu: clock@7010000 {
+			compatible = "allwinner,sun50i-h616-r-ccu";
+			reg = <0x07010000 0x210>;
+			clocks = <&osc24M>, <&rtc 0>, <&rtc 2>,
+				 <&ccu CLK_PLL_PERIPH0>;
+			clock-names = "hosc", "losc", "iosc", "pll-periph";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		r_pio: pinctrl@7022000 {
+			compatible = "allwinner,sun50i-h616-r-pinctrl";
+			reg = <0x07022000 0x400>;
+			interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&r_ccu CLK_R_APB1>, <&osc24M>, <&rtc 0>;
+			clock-names = "apb", "hosc", "losc";
+			gpio-controller;
+			#gpio-cells = <3>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+
+			r_i2c_pins: r-i2c-pins {
+				pins = "PL0", "PL1";
+				function = "s_i2c";
+			};
+
+			r_rsb_pins: r-rsb-pins {
+				pins = "PL0", "PL1";
+				function = "s_rsb";
+			};
+		};
+
+		ir: ir@7040000 {
+				compatible = "allwinner,sun50i-h616-ir",
+					     "allwinner,sun6i-a31-ir";
+				reg = <0x07040000 0x400>;
+				interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&r_ccu CLK_R_APB1_IR>,
+					 <&r_ccu CLK_IR>;
+				clock-names = "apb", "ir";
+				resets = <&r_ccu RST_R_APB1_IR>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&ir_rx_pin>;
+				status = "disabled";
+		};
+
+		r_i2c: i2c@7081400 {
+			compatible = "allwinner,sun50i-h616-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x07081400 0x400>;
+			interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&r_ccu CLK_R_APB2_I2C>;
+			resets = <&r_ccu RST_R_APB2_I2C>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		r_rsb: rsb@7083000 {
+			compatible = "allwinner,sun50i-h616-rsb",
+				     "allwinner,sun8i-a23-rsb";
+			reg = <0x07083000 0x400>;
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&r_ccu CLK_R_APB2_RSB>;
+			clock-frequency = <3000000>;
+			resets = <&r_ccu RST_R_APB2_RSB>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&r_rsb_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
-- 
2.17.5


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 19/20] dt-bindings: arm: sunxi: Add OrangePi Zero 2 binding

[Andre Przywara]

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/arm/sunxi.yaml | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/sunxi.yaml b/Documentation/devicetree/bindings/arm/sunxi.yaml
index 08607c7ec1bf..aeb8771b14c4 100644
--- a/Documentation/devicetree/bindings/arm/sunxi.yaml
+++ b/Documentation/devicetree/bindings/arm/sunxi.yaml
@@ -932,4 +932,9 @@ properties:
           - const: xunlong,orangepi-zero-plus2-h3
           - const: allwinner,sun8i-h3
 
+      - description: Xunlong OrangePi Zero 2
+        items:
+          - const: xunlong,orangepi-zero2
+          - const: allwinner,sun50i-h616
+
 additionalProperties: true
-- 
2.17.5


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 20/20] arm64: dts: allwinner: Add OrangePi Zero 2 .dts

[Andre Przywara]

The OrangePi Zero 2 is a development board with the new H616 SoC.

It features the usual connectors used on those small boards, and comes
with the AXP305, which seems to be compatible with the AXP805.

For more details see: http://linux-sunxi.org/Xunlong_Orange_Pi_Zero2

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
 arch/arm64/boot/dts/allwinner/Makefile        |   1 +
 .../allwinner/sun50i-h616-orangepi-zero2.dts  | 203 ++++++++++++++++++
 2 files changed, 204 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts

diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index 41ce680e5f8d..9ba4b5d92657 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -36,3 +36,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
new file mode 100644
index 000000000000..ca07cae698ce
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
@@ -0,0 +1,203 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (C) 2020 Arm Ltd.
+ */
+
+/dts-v1/;
+
+#include "sun50i-h616.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "OrangePi Zero2";
+	compatible = "xunlong,orangepi-zero2", "allwinner,sun50i-h616";
+
+	aliases {
+		ethernet0 = &emac0;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12 */
+			default-state = "on";
+		};
+
+		led-1 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* PC13 */
+		};
+	};
+
+	reg_vcc5v: vcc5v {
+		/* board wide 5V supply directly from the USB-C socket */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+};
+
+&emac0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ext_rgmii_pins>;
+	phy-mode = "rgmii";
+	phy-handle = <&ext_rgmii_phy>;
+	phy-supply = <&reg_dcdce>;
+	allwinner,rx-delay-ps = <3100>;
+	allwinner,tx-delay-ps = <700>;
+	status = "okay";
+};
+
+&mdio0 {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_dcdce>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;	/* PF6 */
+	bus-width = <4>;
+	status = "okay";
+};
+
+&r_rsb {
+	status = "okay";
+
+	axp305: pmic@745 {
+		compatible = "x-powers,axp305", "x-powers,axp805",
+			     "x-powers,axp806";
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		reg = <0x745>;
+
+		x-powers,self-working-mode;
+		vina-supply = <&reg_vcc5v>;
+		vinb-supply = <&reg_vcc5v>;
+		vinc-supply = <&reg_vcc5v>;
+		vind-supply = <&reg_vcc5v>;
+		vine-supply = <&reg_vcc5v>;
+		aldoin-supply = <&reg_vcc5v>;
+		bldoin-supply = <&reg_vcc5v>;
+		cldoin-supply = <&reg_vcc5v>;
+
+		regulators {
+			reg_aldo1: aldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-sys";
+			};
+
+			reg_aldo2: aldo2 {	/* 3.3V on headers */
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc3v3-ext";
+			};
+
+			reg_aldo3: aldo3 {	/* 3.3V on headers */
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc3v3-ext2";
+			};
+
+			reg_bldo1: bldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc1v8";
+			};
+
+			bldo2 {
+				/* unused */
+			};
+
+			bldo3 {
+				/* unused */
+			};
+
+			bldo4 {
+				/* unused */
+			};
+
+			cldo1 {
+				/* reserved */
+			};
+
+			cldo2 {
+				/* unused */
+			};
+
+			cldo3 {
+				/* unused */
+			};
+
+			reg_dcdca: dcdca {
+				regulator-always-on;
+				regulator-min-microvolt = <810000>;
+				regulator-max-microvolt = <1080000>;
+				regulator-name = "vdd-cpu";
+			};
+
+			reg_dcdcc: dcdcc {
+				regulator-always-on;
+				regulator-min-microvolt = <810000>;
+				regulator-max-microvolt = <1080000>;
+				regulator-name = "vdd-gpu-sys";
+			};
+
+			reg_dcdcd: dcdcd {
+				regulator-always-on;
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-name = "vdd-dram";
+			};
+
+			reg_dcdce: dcdce {
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-eth-mmc";
+			};
+
+			sw {
+				/* unused */
+			};
+		};
+	};
+};
+
+&spi0  {
+	status = "okay";
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <40000000>;
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_ph_pins>;
+	status = "okay";
+};
-- 
2.17.5


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v5 05/20] Input: axp20x-pek: Bail out if AXP has no interrupt line connected

[Dmitry Torokhov]

Hi Andre,

On Wed, Jan 27, 2021 at 05:24:45PM +0000, Andre Przywara wrote:
> On at least one board (Orangepi Zero2) the AXP305 PMIC does not have its
> interrupt line connected to the CPU (mostly because the H616 SoC does
> not feature an NMI pin anymore).
> After allowing the AXP driver to proceed without an "interrupts"
> property [1], the axp20x-pek driver crashes with a NULL pointer
> dereference (see below).
> 
> Check for the regmap_irqc member to be not NULL before proceeding with
> probe. This gets normally filled by the call to regmap_add_irq_chip(),
> which we allow to skip now, when the DT node lacks an interrupt
> property.

No, the driver is not the right place to patch this; regmap should be
fixed so it does not crash instead.

Thanks.

-- 
Dmitry

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v5 10/20] dt-bindings: i2c: mv64xxx: Add H616 compatible string

[Wolfram Sang]

[-- Attachment #1.1: Type: text/plain, Size: 480 bytes --]

On Wed, Jan 27, 2021 at 05:24:50PM +0000, Andre Przywara wrote:
> Add the obvious compatible name to the existing I2C binding, and pair
> it with the existing A31 fallback compatible string, as the devices
> are compatible.
> 
> On the way use enums to group all compatible devices together.
> 
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> Acked-by: Rob Herring <robh@kernel.org>
> Acked-by: Wolfram Sang <wsa@kernel.org>

Applied to for-next, thanks!


[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]

[-- Attachment #2: Type: text/plain, Size: 176 bytes --]

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v5 04/20] dt-bindings: mfd: axp20x: Add AXP305 compatible (plus optional IRQ)

[Maxime Ripard]

[-- Attachment #1.1: Type: text/plain, Size: 465 bytes --]

On Wed, Jan 27, 2021 at 05:24:44PM +0000, Andre Przywara wrote:
> The AXP305 PMIC used in AXP805 seems to be fully compatible to the
> AXP805 PMIC, so add the proper chain of compatible strings.
> 
> Also at least on one board (Orangepi Zero2) there is no interrupt line
> connected to the CPU, so make the "interrupts" property optional.
> 
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Acked-by: Maxime Ripard <mripard@kernel.org>

Maxime

[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

[-- Attachment #2: Type: text/plain, Size: 176 bytes --]

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v5 06/20] mfd: axp20x: Allow AXP chips without interrupt lines

[Maxime Ripard]

[-- Attachment #1.1: Type: text/plain, Size: 764 bytes --]

On Wed, Jan 27, 2021 at 05:24:46PM +0000, Andre Przywara wrote:
> Currently the AXP chip requires to have its IRQ line connected to some
> interrupt controller, and will fail probing when this is not the case.
> 
> On a new Allwinner SoC (H616) there is no NMI pin anymore, and at
> least one board does not connect the AXP's IRQ pin to anything else,
> so the interrupt functionality of the AXP chip is simply not available.
> 
> Check whether the interrupt line number returned by the platform code is
> valid, before trying to register the irqchip. If not, we skip this
> registration, to avoid the driver to bail out completely.
> 
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Acked-by: Maxime Ripard <mripard@kernel.org>

Maxime

[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

[-- Attachment #2: Type: text/plain, Size: 176 bytes --]

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v5 12/20] dt-bindings: rtc: sun6i: Add H616 compatible string

[Maxime Ripard]

[-- Attachment #1.1: Type: text/plain, Size: 390 bytes --]

On Wed, Jan 27, 2021 at 05:24:52PM +0000, Andre Przywara wrote:
> Add the obvious compatible name to the existing RTC binding, and pair
> it with the existing H6 fallback compatible string, as the devices are
> compatible.
> 
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> Acked-by: Rob Herring <robh@kernel.org>

Acked-by: Maxime Ripard <mripard@kernel.org>

maxime

[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

[-- Attachment #2: Type: text/plain, Size: 176 bytes --]

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v5 15/20] dt-bindings: net: sun8i-emac: Add H616 compatible string

[Maxime Ripard]

[-- Attachment #1.1: Type: text/plain, Size: 419 bytes --]

On Wed, Jan 27, 2021 at 05:24:55PM +0000, Andre Przywara wrote:
> Add the obvious compatible name to the existing EMAC binding, and pair
> it with the existing A64 fallback compatible string, as the devices are
> compatible.
> 
> On the way use enums to group the compatible devices together.
> 
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Acked-by: Maxime Ripard <mripard@kernel.org>

Maxime

[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

[-- Attachment #2: Type: text/plain, Size: 176 bytes --]

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v5 16/20] net: stmmac: dwmac-sun8i: Prepare for second EMAC clock register

[Maxime Ripard]

[-- Attachment #1.1: Type: text/plain, Size: 578 bytes --]

On Wed, Jan 27, 2021 at 05:24:56PM +0000, Andre Przywara wrote:
> The Allwinner H616 SoC has two EMAC controllers, with the second one
> being tied to the internal PHY, but also using a separate EMAC clock
> register.
> 
> To tell the driver about which clock register to use, we add a parameter
> to our syscon phandle. The driver will use this value as an index into
> the regmap, so that we can address more than the first register, if
> needed.
> 
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Acked-by: Maxime Ripard <mripard@kernel.org>

Maxime

[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

[-- Attachment #2: Type: text/plain, Size: 176 bytes --]

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v5 05/20] Input: axp20x-pek: Bail out if AXP has no interrupt line connected

[Andre Przywara]

On Wed, 27 Jan 2021 11:42:15 -0800
Dmitry Torokhov <dmitry.torokhov@gmail.com> wrote:

Hi Dmitry,

thanks for your feedback!

> On Wed, Jan 27, 2021 at 05:24:45PM +0000, Andre Przywara wrote:
> > On at least one board (Orangepi Zero2) the AXP305 PMIC does not have its
> > interrupt line connected to the CPU (mostly because the H616 SoC does
> > not feature an NMI pin anymore).
> > After allowing the AXP driver to proceed without an "interrupts"
> > property [1], the axp20x-pek driver crashes with a NULL pointer
> > dereference (see below).
> > 
> > Check for the regmap_irqc member to be not NULL before proceeding with
> > probe. This gets normally filled by the call to regmap_add_irq_chip(),
> > which we allow to skip now, when the DT node lacks an interrupt
> > property.  
> 
> No, the driver is not the right place to patch this; regmap should be
> fixed so it does not crash instead.

I am not sure this is the right approach, those regmap functions look
more like an internal interface to me, with lots of wrapper functions
happily dereferencing pointers and reaching into structs. Moving
NULL checks into those does not sound like the right thing. CC:ing Mark
for more opinions on this.

A more general solution would be to not instantiate this driver here
at all, when we don't have an interrupt line.
However at the moment the AXP MFD driver uses a const struct to hold
all MFD cells, so there is no easy way of omitting the power key
device dynamically. And even then it would hard code the requirement
for an interrupt into the MFD driver, when this could be considered an
implementation detail of the axp20x-pek driver.

That's why I came up with this patch here, which was the easiest and
cleanest: This driver *requires* a valid regmap_irqc, so it should
verify this at probe time, kind of like a normal driver would bail out
if no IRQ line could be reserved.

Let me know what you think!

Cheers,
Andre

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v5 05/20] Input: axp20x-pek: Bail out if AXP has no interrupt line connected

[Mark Brown]

[-- Attachment #1.1: Type: text/plain, Size: 1834 bytes --]

On Thu, Jan 28, 2021 at 11:11:28AM +0000, Andre Przywara wrote:
> Dmitry Torokhov <dmitry.torokhov@gmail.com> wrote:
> > On Wed, Jan 27, 2021 at 05:24:45PM +0000, Andre Przywara wrote:

> > > Check for the regmap_irqc member to be not NULL before proceeding with
> > > probe. This gets normally filled by the call to regmap_add_irq_chip(),
> > > which we allow to skip now, when the DT node lacks an interrupt
> > > property.  

It sounds like you're trying to register an IRQ chip with a somehow
bogus configuration?

> > No, the driver is not the right place to patch this; regmap should be
> > fixed so it does not crash instead.

> I am not sure this is the right approach, those regmap functions look
> more like an internal interface to me, with lots of wrapper functions
> happily dereferencing pointers and reaching into structs. Moving
> NULL checks into those does not sound like the right thing. CC:ing Mark
> for more opinions on this.

Without having seen the actual issue if you're trying to register an
interrupt controller with a known broken hardware configuration that
does seem like something the caller just shouldn't be doing, it's not
something that's going to transiently happen at runtime and we're very
much trusting that the caller got things right.

> A more general solution would be to not instantiate this driver here
> at all, when we don't have an interrupt line.
> However at the moment the AXP MFD driver uses a const struct to hold
> all MFD cells, so there is no easy way of omitting the power key
> device dynamically. And even then it would hard code the requirement
> for an interrupt into the MFD driver, when this could be considered an
> implementation detail of the axp20x-pek driver.

Another approach is to just register the optional device separately.

[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]

[-- Attachment #2: Type: text/plain, Size: 176 bytes --]

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v5 05/20] Input: axp20x-pek: Bail out if AXP has no interrupt line connected

[Andre Przywara]

On Thu, 28 Jan 2021 11:36:01 +0000
Mark Brown <broonie@kernel.org> wrote:

> On Thu, Jan 28, 2021 at 11:11:28AM +0000, Andre Przywara wrote:
> > Dmitry Torokhov <dmitry.torokhov@gmail.com> wrote:  
> > > On Wed, Jan 27, 2021 at 05:24:45PM +0000, Andre Przywara wrote:  
> 
> > > > Check for the regmap_irqc member to be not NULL before proceeding with
> > > > probe. This gets normally filled by the call to regmap_add_irq_chip(),
> > > > which we allow to skip now, when the DT node lacks an interrupt
> > > > property.    
> 
> It sounds like you're trying to register an IRQ chip with a somehow
> bogus configuration?

Quick background: Those AXP PMICs have an IRQ pin, that was always
connected to the NMI pin on Allwinner SoCs. This was used for the power
button GPIO interrupt. Now the H616 does not have this pin anymore, and
the board does not use a GPIO either.
I patched the AXP MFD driver [1] to skip the regmap-irq creation when no
interrupts DT property was found, but this NULL pointer now
understandably confuses the -pek driver, and leads to this crash:

http://lists.infradead.org/pipermail/linux-arm-kernel/2021-January/634969.html

Hence I wanted to plug this hole, which seems useful regardless of this
particular issue.

[1]
http://lists.infradead.org/pipermail/linux-arm-kernel/2021-January/634971.html

> > > No, the driver is not the right place to patch this; regmap should be
> > > fixed so it does not crash instead.  
> 
> > I am not sure this is the right approach, those regmap functions look
> > more like an internal interface to me, with lots of wrapper functions
> > happily dereferencing pointers and reaching into structs. Moving
> > NULL checks into those does not sound like the right thing. CC:ing Mark
> > for more opinions on this.  
> 
> Without having seen the actual issue if you're trying to register an
> interrupt controller with a known broken hardware configuration that
> does seem like something the caller just shouldn't be doing, it's not
> something that's going to transiently happen at runtime and we're very
> much trusting that the caller got things right.
> 
> > A more general solution would be to not instantiate this driver here
> > at all, when we don't have an interrupt line.
> > However at the moment the AXP MFD driver uses a const struct to hold
> > all MFD cells, so there is no easy way of omitting the power key
> > device dynamically. And even then it would hard code the requirement
> > for an interrupt into the MFD driver, when this could be considered an
> > implementation detail of the axp20x-pek driver.  
> 
> Another approach is to just register the optional device separately.

I will have a look at how much this takes.

Thanks,
Andre

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v5 05/20] Input: axp20x-pek: Bail out if AXP has no interrupt line connected

[Mark Brown]

[-- Attachment #1.1: Type: text/plain, Size: 1916 bytes --]

On Thu, Jan 28, 2021 at 12:31:36PM +0000, Andre Przywara wrote:
> Mark Brown <broonie@kernel.org> wrote:

> > It sounds like you're trying to register an IRQ chip with a somehow
> > bogus configuration?

> I patched the AXP MFD driver [1] to skip the regmap-irq creation when no
> interrupts DT property was found, but this NULL pointer now
> understandably confuses the -pek driver, and leads to this crash:

> http://lists.infradead.org/pipermail/linux-arm-kernel/2021-January/634969.html

> Hence I wanted to plug this hole, which seems useful regardless of this
> particular issue.

The driver code here looks pretty confused.  It appears to be looking up
the interrupt to use from a resource (which is what I'd expect for a MFD
child) then for reasons I can't fathom trying to pass that resource into
regmap_irq_get_virq() which is at best going to just return the value
that was passed in but may potentially end up just returning a random
interrupt other than the one that was asked for since we're passing in a
global interrupt number rather than a controller relative one.  I really
can't tell what's supposed to be going on there.  A driver should either
use resources or it should use regmap_irq_get_virq(), using both is a
bug.

The MFD for this device is also just plain buggy in that it is providing
IRQ resources to the children when there is in fact no support for the
interrupts on the device in the system.  This means that the MFD core
sees that it has no interrupt domain, assumes that those interrupt
resources are in fact absolute interrupt numbers and passes them
straight through to the children.  This means that the children will
just be requesting random interrupts in the system which may actually
exist and be requestable which probably isn't going to end well.  When
there is no interrupt controller the parent should not be trying to
supply interrupt resources to the children at all.

[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]

[-- Attachment #2: Type: text/plain, Size: 176 bytes --]

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v5 12/20] dt-bindings: rtc: sun6i: Add H616 compatible string

[Andre Przywara]

On Sun, 31 Jan 2021 14:44:40 +0100
Jernej Škrabec <jernej.skrabec@siol.net> wrote:

Hi Jernej,

> Dne sreda, 27. januar 2021 ob 18:24:52 CET je Andre Przywara napisal(a):
> > Add the obvious compatible name to the existing RTC binding, and pair
> > it with the existing H6 fallback compatible string, as the devices are
> > compatible.  
> 
> After close lookup I would disagree with this observation. Major difference is 
> that H616 doesn't support usage of external 32768 Hz oscillator. It uses 24 
> MHz oscillator with divider for that case. Due to that change, whole logic for 
> external oscillator should go out. Additionally, this logic overwrites default 
> value in LOSC_CTRL register, which is not nice (there is no documentation for 
> those bits).

Thanks for the heads up, and I wonder if there is more to that. From
comparing the RTC documentation, I wonder if we should actually have
incoming clocks in the bindings (the crystals / external clock sources
with 32KHz, 16MHz, 24MHz). Then we could actually model which crystals
the board provides. It seems like the H6 made the 32KHz OSC optional,
and the H616 simply doesn't support it anymore - at the very least I
don't see any X32K pins anymore.

But more importantly: looking more closely (I only skimmed over the
register summary back then) the actual RTC registers are different:
the H616 encodes a linear day number (vs. a broken-down D-M-Y), also the
time-of-day register is different.

So we definitely need a driver update, and hence need to drop this
patch.

Cheers,
Andre

> Best regards,
> Jernej
> 
> > 
> > Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> > Acked-by: Rob Herring <robh@kernel.org>
> > ---
> >  .../devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml       | 3 +++
> >  1 file changed, 3 insertions(+)
> > 
> > diff --git a/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-  
> rtc.yaml b/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml
> > index b1b0ee769b71..4193e5813344 100644
> > --- a/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml
> > +++ b/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml
> > @@ -26,6 +26,9 @@ properties:
> >            - const: allwinner,sun50i-a64-rtc
> >            - const: allwinner,sun8i-h3-rtc
> >        - const: allwinner,sun50i-h6-rtc
> > +      - items:
> > +          - const: allwinner,sun50i-h616-rtc
> > +          - const: allwinner,sun50i-h6-rtc
> >  
> >    reg:
> >      maxItems: 1
> > -- 
> > 2.17.5
> > 
> >   
> 
> 


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [linux-sunxi] [PATCH v5 04/20] dt-bindings: mfd: axp20x: Add AXP305 compatible (plus optional IRQ)

[Chen-Yu Tsai]

Hi,

On Thu, Jan 28, 2021 at 1:26 AM Andre Przywara <andre.przywara@arm.com> wrote:
>
> The AXP305 PMIC used in AXP805 seems to be fully compatible to the
                          ^
This statement doesn't quite make sense. I assume you wanted to mention
a board or the H616 SoC here?

> AXP805 PMIC, so add the proper chain of compatible strings.
>
> Also at least on one board (Orangepi Zero2) there is no interrupt line
> connected to the CPU, so make the "interrupts" property optional.
>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> ---
>  Documentation/devicetree/bindings/mfd/axp20x.txt | 3 ++-
>  1 file changed, 2 insertions(+), 1 deletion(-)
>
> diff --git a/Documentation/devicetree/bindings/mfd/axp20x.txt b/Documentation/devicetree/bindings/mfd/axp20x.txt
> index 4991a6415796..4fd748101e3c 100644
> --- a/Documentation/devicetree/bindings/mfd/axp20x.txt
> +++ b/Documentation/devicetree/bindings/mfd/axp20x.txt
> @@ -26,10 +26,10 @@ Required properties:
>      * "x-powers,axp803"
>      * "x-powers,axp806"
>      * "x-powers,axp805", "x-powers,axp806"
> +    * "x-powers,axp803", "x-powers,axp805", "x-powers,axp806"

axp305? axp803 is used with A64 IIRC.

ChenYu

>      * "x-powers,axp809"
>      * "x-powers,axp813"
>  - reg: The I2C slave address or RSB hardware address for the AXP chip
> -- interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin
>  - interrupt-controller: The PMIC has its own internal IRQs
>  - #interrupt-cells: Should be set to 1
>
> @@ -43,6 +43,7 @@ more information:
>                         AXP20x/LDO3: software-based implementation
>
>  Optional properties:
> +- interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin
>  - x-powers,dcdc-freq: defines the work frequency of DC-DC in KHz
>                       AXP152/20X: range:  750-1875, Default: 1.5 MHz
>                       AXP22X/8XX: range: 1800-4050, Default: 3   MHz
> --
> 2.17.5
>
> --
> You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
> To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe@googlegroups.com.
> To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20210127172500.13356-5-andre.przywara%40arm.com.

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v5 14/20] dt-bindings: bus: rsb: Add H616 compatible string

[Chen-Yu Tsai]

On Thu, Jan 28, 2021 at 1:26 AM Andre Przywara <andre.przywara@arm.com> wrote:
>
> Add the obvious compatible name to the existing RSB binding, and pair
> it with the existing A23 fallback compatible string, as the devices are
> compatible.
>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Acked-by: Chen-Yu Tsai <wens@csie.org>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [linux-sunxi] Re: [PATCH v5 06/20] mfd: axp20x: Allow AXP chips without interrupt lines

[Chen-Yu Tsai]

On Thu, Jan 28, 2021 at 6:15 PM Maxime Ripard <maxime@cerno.tech> wrote:
>
> On Wed, Jan 27, 2021 at 05:24:46PM +0000, Andre Przywara wrote:
> > Currently the AXP chip requires to have its IRQ line connected to some
> > interrupt controller, and will fail probing when this is not the case.
> >
> > On a new Allwinner SoC (H616) there is no NMI pin anymore, and at
> > least one board does not connect the AXP's IRQ pin to anything else,
> > so the interrupt functionality of the AXP chip is simply not available.
> >
> > Check whether the interrupt line number returned by the platform code is
> > valid, before trying to register the irqchip. If not, we skip this
> > registration, to avoid the driver to bail out completely.
> >
> > Signed-off-by: Andre Przywara <andre.przywara@arm.com>
>
> Acked-by: Maxime Ripard <mripard@kernel.org>

Acked-by: Chen-Yu Tsai <wens@csie.org>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v5 06/20] mfd: axp20x: Allow AXP chips without interrupt lines

[Lee Jones]

On Wed, 27 Jan 2021, Andre Przywara wrote:

> Currently the AXP chip requires to have its IRQ line connected to some
> interrupt controller, and will fail probing when this is not the case.
> 
> On a new Allwinner SoC (H616) there is no NMI pin anymore, and at
> least one board does not connect the AXP's IRQ pin to anything else,
> so the interrupt functionality of the AXP chip is simply not available.
> 
> Check whether the interrupt line number returned by the platform code is
> valid, before trying to register the irqchip. If not, we skip this
> registration, to avoid the driver to bail out completely.
> 
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> ---
>  drivers/mfd/axp20x.c | 17 +++++++++++------
>  1 file changed, 11 insertions(+), 6 deletions(-)

For my own reference (apply this as-is to your sign-off block):

  Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>

-- 
Lee Jones [李琼斯]
Senior Technical Lead - Developer Services
Linaro.org │ Open source software for Arm SoCs
Follow Linaro: Facebook | Twitter | Blog

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [linux-sunxi] [PATCH v5 04/20] dt-bindings: mfd: axp20x: Add AXP305 compatible (plus optional IRQ)

[Andre Przywara]

On Tue, 2 Feb 2021 15:55:50 +0800
Chen-Yu Tsai <wens@csie.org> wrote:

Hi,

> On Thu, Jan 28, 2021 at 1:26 AM Andre Przywara <andre.przywara@arm.com> wrote:
> >
> > The AXP305 PMIC used in AXP805 seems to be fully compatible to the  
>                           ^
> This statement doesn't quite make sense. I assume you wanted to mention
> a board or the H616 SoC here?

Argh, indeed!

> > AXP805 PMIC, so add the proper chain of compatible strings.
> >
> > Also at least on one board (Orangepi Zero2) there is no interrupt line
> > connected to the CPU, so make the "interrupts" property optional.
> >
> > Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> > ---
> >  Documentation/devicetree/bindings/mfd/axp20x.txt | 3 ++-
> >  1 file changed, 2 insertions(+), 1 deletion(-)
> >
> > diff --git a/Documentation/devicetree/bindings/mfd/axp20x.txt b/Documentation/devicetree/bindings/mfd/axp20x.txt
> > index 4991a6415796..4fd748101e3c 100644
> > --- a/Documentation/devicetree/bindings/mfd/axp20x.txt
> > +++ b/Documentation/devicetree/bindings/mfd/axp20x.txt
> > @@ -26,10 +26,10 @@ Required properties:
> >      * "x-powers,axp803"
> >      * "x-powers,axp806"
> >      * "x-powers,axp805", "x-powers,axp806"
> > +    * "x-powers,axp803", "x-powers,axp805", "x-powers,axp806"  
> 
> axp305? axp803 is used with A64 IIRC.

Oh, well spotted. This AXP naming already confused me when they were
all called 80x, now using 30x gave me the rest ;-)

Sorry for the blunder!

Cheers,
Andre

> 
> ChenYu
> 
> >      * "x-powers,axp809"
> >      * "x-powers,axp813"
> >  - reg: The I2C slave address or RSB hardware address for the AXP chip
> > -- interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin
> >  - interrupt-controller: The PMIC has its own internal IRQs
> >  - #interrupt-cells: Should be set to 1
> >
> > @@ -43,6 +43,7 @@ more information:
> >                         AXP20x/LDO3: software-based implementation
> >
> >  Optional properties:
> > +- interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin
> >  - x-powers,dcdc-freq: defines the work frequency of DC-DC in KHz
> >                       AXP152/20X: range:  750-1875, Default: 1.5 MHz
> >                       AXP22X/8XX: range: 1800-4050, Default: 3   MHz
> > --
> > 2.17.5
> >
> > --
> > You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
> > To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe@googlegroups.com.
> > To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20210127172500.13356-5-andre.przywara%40arm.com.  


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v5 04/20] dt-bindings: mfd: axp20x: Add AXP305 compatible (plus optional IRQ)

[Rob Herring]

On Wed, Jan 27, 2021 at 05:24:44PM +0000, Andre Przywara wrote:
> The AXP305 PMIC used in AXP805 seems to be fully compatible to the
> AXP805 PMIC, so add the proper chain of compatible strings.
> 
> Also at least on one board (Orangepi Zero2) there is no interrupt line
> connected to the CPU, so make the "interrupts" property optional.
> 
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> ---
>  Documentation/devicetree/bindings/mfd/axp20x.txt | 3 ++-
>  1 file changed, 2 insertions(+), 1 deletion(-)
> 
> diff --git a/Documentation/devicetree/bindings/mfd/axp20x.txt b/Documentation/devicetree/bindings/mfd/axp20x.txt
> index 4991a6415796..4fd748101e3c 100644
> --- a/Documentation/devicetree/bindings/mfd/axp20x.txt
> +++ b/Documentation/devicetree/bindings/mfd/axp20x.txt
> @@ -26,10 +26,10 @@ Required properties:
>      * "x-powers,axp803"
>      * "x-powers,axp806"
>      * "x-powers,axp805", "x-powers,axp806"
> +    * "x-powers,axp803", "x-powers,axp805", "x-powers,axp806"

I don't normally (yet) ask for schema conversions on compatible 
additions, but this is one of the few remaining compatibles with no 
schema for allwinner. So a conversion here would be nice. BTW, dtschema 
now has a better check for this (-m option) without the false positives. 
I plan to turn on the option soon (doesn't matter for dtbs as they all 
have lots of warnings, but bindings also get warnings).

Either way,

Acked-by: Rob Herring <robh@kernel.org>


>      * "x-powers,axp809"
>      * "x-powers,axp813"
>  - reg: The I2C slave address or RSB hardware address for the AXP chip
> -- interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin
>  - interrupt-controller: The PMIC has its own internal IRQs
>  - #interrupt-cells: Should be set to 1
>  
> @@ -43,6 +43,7 @@ more information:
>  			AXP20x/LDO3: software-based implementation
>  
>  Optional properties:
> +- interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin
>  - x-powers,dcdc-freq: defines the work frequency of DC-DC in KHz
>  		      AXP152/20X: range:  750-1875, Default: 1.5 MHz
>  		      AXP22X/8XX: range: 1800-4050, Default: 3   MHz
> -- 
> 2.17.5
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v5 15/20] dt-bindings: net: sun8i-emac: Add H616 compatible string

[Rob Herring]

On Wed, 27 Jan 2021 17:24:55 +0000, Andre Przywara wrote:
> Add the obvious compatible name to the existing EMAC binding, and pair
> it with the existing A64 fallback compatible string, as the devices are
> compatible.
> 
> On the way use enums to group the compatible devices together.
> 
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> ---
>  .../devicetree/bindings/net/allwinner,sun8i-a83t-emac.yaml    | 4 +++-
>  1 file changed, 3 insertions(+), 1 deletion(-)
> 

Acked-by: Rob Herring <robh@kernel.org>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel