* [PATCH v5 0/3] J7200: Add support for GPIO and higher speed modes in MMCSD subsystems
@ 2021-03-10 16:19 Aswath Govindraju
2021-03-10 16:19 ` [PATCH v5 1/3] arm64: dts: ti: k3-j7200: Add gpio nodes Aswath Govindraju
` (2 more replies)
0 siblings, 3 replies; 8+ messages in thread
From: Aswath Govindraju @ 2021-03-10 16:19 UTC (permalink / raw)
Cc: Vignesh Raghavendra, Lokesh Vutla, Kishon Vijay Abraham I,
a-govindraju, Nishanth Menon, Tero Kristo, Rob Herring,
linux-arm-kernel, devicetree, linux-kernel
The following series of patches
- Add support for GPIO subsystem in main and wakeup domains.
- Add voltage regulator device tree nodes and their corresponding pinmux
to support power cycle and voltage switch required for UHS-I modes
- sets respective tags in sdhci0 node to support higher speeds
- remove no-1-8-v tag from sdhci1 node to support UHS-I modes
- Update delay values for various speed modes supported.
test logs
- eMMC HS400 speed mode
https://pastebin.ubuntu.com/p/xqZt34mRWf/
- SD SDR104 speed mode
https://pastebin.ubuntu.com/p/qM2H85SQvX/
- GPIO logs
https://pastebin.ubuntu.com/p/7WXdRxxdWz/
Changes since v4:
- Added main_i2c0 pinmux required for doing power cycles to MMCSD1
subsystem
- Updated delay values for various speed modes supported
- Corrected the ti,ngpio property to indicate highest gpio lines that
can be accessed.
- Reran the performace tests
Changes since v3:
- Removed patch (1 in v3).
- Rebased and included patches that add support for GPIO from series [1].
- Re-ran the performace tests for SD and eMMC.
Changes since v2:
- Added main_gpio0 DT node
- Added voltage regulator device tree nodes required to support UHS-I modes
Changes since v1:
- squashed the two patches into one
- added performance logs for the above mentioned speed modes
Aswath Govindraju (1):
arm64: dts: ti: k3-j7200: Add support for higher speed modes and
update delay select values for MMCSD subsystems
Faiz Abbas (2):
arm64: dts: ti: k3-j7200: Add gpio nodes
arm64: dts: ti: k3-j7200-common-proc-board: Disable unused gpio
modules
.../dts/ti/k3-j7200-common-proc-board.dts | 58 +++++++++++++
arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 86 ++++++++++++++++++-
.../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi | 34 ++++++++
3 files changed, 176 insertions(+), 2 deletions(-)
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH v5 1/3] arm64: dts: ti: k3-j7200: Add gpio nodes
2021-03-10 16:19 [PATCH v5 0/3] J7200: Add support for GPIO and higher speed modes in MMCSD subsystems Aswath Govindraju
@ 2021-03-10 16:19 ` Aswath Govindraju
2021-03-11 12:30 ` Grygorii Strashko
2021-03-10 16:19 ` [PATCH v5 2/3] arm64: dts: ti: k3-j7200-common-proc-board: Disable unused gpio modules Aswath Govindraju
2021-03-10 16:19 ` [PATCH v5 3/3] arm64: dts: ti: k3-j7200: Add support for higher speed modes and update delay select values for MMCSD subsystems Aswath Govindraju
2 siblings, 1 reply; 8+ messages in thread
From: Aswath Govindraju @ 2021-03-10 16:19 UTC (permalink / raw)
Cc: Vignesh Raghavendra, Lokesh Vutla, Kishon Vijay Abraham I,
a-govindraju, Faiz Abbas, Sekhar Nori, Nishanth Menon,
Tero Kristo, Rob Herring, linux-arm-kernel, devicetree,
linux-kernel
From: Faiz Abbas <faiz_abbas@ti.com>
There are 4 instances of gpio modules in main domain:
gpio0, gpio2, gpio4 and gpio6
Groups are created to provide protection between different processor
virtual worlds. Each of these modules I/O pins are muxed within the
group. Exactly one module can be selected to control the corresponding
pin by selecting it in the pad mux configuration registers.
This group in main domain pins out 69 lines (5 banks). Add DT modes for
each module instance in the main domain.
Similar to the gpio groups in main domain, there is one gpio group in
wakeup domain with 2 module instances in it.
The gpio group pins out 72 pins (6 banks) of the first 85 gpio lines. Add
DT nodes for each module instance in the wakeup domain.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
---
arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 72 +++++++++++++++++++
.../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi | 34 +++++++++
2 files changed, 106 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
index 17477ab0fd8e..e60650a62b14 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
@@ -672,6 +672,78 @@
};
};
+ main_gpio0: gpio@600000 {
+ compatible = "ti,j721e-gpio", "ti,keystone-gpio";
+ reg = <0x00 0x00600000 0x00 0x100>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-parent = <&main_gpio_intr>;
+ interrupts = <145>, <146>, <147>, <148>,
+ <149>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ #address-cells = <0>;
+ ti,ngpio = <69>;
+ ti,davinci-gpio-unbanked = <0>;
+ power-domains = <&k3_pds 105 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 105 0>;
+ clock-names = "gpio";
+ };
+
+ main_gpio2: gpio@610000 {
+ compatible = "ti,j721e-gpio", "ti,keystone-gpio";
+ reg = <0x00 0x00610000 0x00 0x100>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-parent = <&main_gpio_intr>;
+ interrupts = <154>, <155>, <156>, <157>,
+ <158>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ #address-cells = <0>;
+ ti,ngpio = <69>;
+ ti,davinci-gpio-unbanked = <0>;
+ power-domains = <&k3_pds 107 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 107 0>;
+ clock-names = "gpio";
+ };
+
+ main_gpio4: gpio@620000 {
+ compatible = "ti,j721e-gpio", "ti,keystone-gpio";
+ reg = <0x00 0x00620000 0x00 0x100>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-parent = <&main_gpio_intr>;
+ interrupts = <163>, <164>, <165>, <166>,
+ <167>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ #address-cells = <0>;
+ ti,ngpio = <69>;
+ ti,davinci-gpio-unbanked = <0>;
+ power-domains = <&k3_pds 109 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 109 0>;
+ clock-names = "gpio";
+ };
+
+ main_gpio6: gpio@630000 {
+ compatible = "ti,j721e-gpio", "ti,keystone-gpio";
+ reg = <0x00 0x00630000 0x00 0x100>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-parent = <&main_gpio_intr>;
+ interrupts = <172>, <173>, <174>, <175>,
+ <176>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ #address-cells = <0>;
+ ti,ngpio = <69>;
+ ti,davinci-gpio-unbanked = <0>;
+ power-domains = <&k3_pds 111 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 111 0>;
+ clock-names = "gpio";
+ };
+
main_r5fss0: r5fss@5c00000 {
compatible = "ti,j7200-r5fss";
ti,cluster-mode = <1>;
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
index 359e3e8a8cd0..1dd5b30edc6c 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
@@ -107,6 +107,40 @@
ti,interrupt-ranges = <16 960 16>;
};
+ wkup_gpio0: gpio@42110000 {
+ compatible = "ti,j721e-gpio", "ti,keystone-gpio";
+ reg = <0x00 0x42110000 0x00 0x100>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-parent = <&wkup_gpio_intr>;
+ interrupts = <103>, <104>, <105>, <106>, <107>, <108>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ #address-cells = <0>;
+ ti,ngpio = <85>;
+ ti,davinci-gpio-unbanked = <0>;
+ power-domains = <&k3_pds 113 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 113 0>;
+ clock-names = "gpio";
+ };
+
+ wkup_gpio1: gpio@42100000 {
+ compatible = "ti,j721e-gpio", "ti,keystone-gpio";
+ reg = <0x00 0x42100000 0x00 0x100>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-parent = <&wkup_gpio_intr>;
+ interrupts = <112>, <113>, <114>, <115>, <116>, <117>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ #address-cells = <0>;
+ ti,ngpio = <85>;
+ ti,davinci-gpio-unbanked = <0>;
+ power-domains = <&k3_pds 114 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 114 0>;
+ clock-names = "gpio";
+ };
+
mcu_navss: bus@28380000 {
compatible = "simple-mfd";
#address-cells = <2>;
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v5 2/3] arm64: dts: ti: k3-j7200-common-proc-board: Disable unused gpio modules
2021-03-10 16:19 [PATCH v5 0/3] J7200: Add support for GPIO and higher speed modes in MMCSD subsystems Aswath Govindraju
2021-03-10 16:19 ` [PATCH v5 1/3] arm64: dts: ti: k3-j7200: Add gpio nodes Aswath Govindraju
@ 2021-03-10 16:19 ` Aswath Govindraju
2021-03-16 12:01 ` Grygorii Strashko
2021-03-10 16:19 ` [PATCH v5 3/3] arm64: dts: ti: k3-j7200: Add support for higher speed modes and update delay select values for MMCSD subsystems Aswath Govindraju
2 siblings, 1 reply; 8+ messages in thread
From: Aswath Govindraju @ 2021-03-10 16:19 UTC (permalink / raw)
Cc: Vignesh Raghavendra, Lokesh Vutla, Kishon Vijay Abraham I,
a-govindraju, Faiz Abbas, Sekhar Nori, Nishanth Menon,
Tero Kristo, Rob Herring, linux-arm-kernel, devicetree,
linux-kernel
From: Faiz Abbas <faiz_abbas@ti.com>
There are 6 gpio instances inside SoC with 2 groups as show below:
Group one: wkup_gpio0, wkup_gpio1
Group two: main_gpio0, main_gpio2, main_gpio4, main_gpio6
Only one instance from each group can be used at a time. So use main_gpio0
and wkup_gpio0 in current linux context and disable the rest of the nodes.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
---
.../boot/dts/ti/k3-j7200-common-proc-board.dts | 16 ++++++++++++++++
1 file changed, 16 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
index 4a7182abccf5..b493f939b09a 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
@@ -122,6 +122,22 @@
status = "disabled";
};
+&main_gpio2 {
+ status = "disabled";
+};
+
+&main_gpio4 {
+ status = "disabled";
+};
+
+&main_gpio6 {
+ status = "disabled";
+};
+
+&wkup_gpio1 {
+ status = "disabled";
+};
+
&mcu_cpsw {
pinctrl-names = "default";
pinctrl-0 = <&mcu_cpsw_pins_default &mcu_mdio_pins_default>;
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v5 3/3] arm64: dts: ti: k3-j7200: Add support for higher speed modes and update delay select values for MMCSD subsystems
2021-03-10 16:19 [PATCH v5 0/3] J7200: Add support for GPIO and higher speed modes in MMCSD subsystems Aswath Govindraju
2021-03-10 16:19 ` [PATCH v5 1/3] arm64: dts: ti: k3-j7200: Add gpio nodes Aswath Govindraju
2021-03-10 16:19 ` [PATCH v5 2/3] arm64: dts: ti: k3-j7200-common-proc-board: Disable unused gpio modules Aswath Govindraju
@ 2021-03-10 16:19 ` Aswath Govindraju
2021-03-18 15:15 ` Kishon Vijay Abraham I
2 siblings, 1 reply; 8+ messages in thread
From: Aswath Govindraju @ 2021-03-10 16:19 UTC (permalink / raw)
Cc: Vignesh Raghavendra, Lokesh Vutla, Kishon Vijay Abraham I,
a-govindraju, Nishanth Menon, Tero Kristo, Rob Herring,
linux-arm-kernel, devicetree, linux-kernel
The following speed modes are now supported in J7200 SoC,
- HS200 and HS400 modes at 1.8 V card voltage, in MMCSD0 subsystem [1].
- UHS-I speed modes in MMCSD1 subsystem [1].
Add support for UHS-I modes by adding voltage regulator device tree nodes
and corresponding pinmux details, to power cycle and voltage switch cards.
Set respective tags in sdhci0 and remove no-1-8-v tag from sdhci1
device tree nodes.
Also update the delay values for various speed modes supported, based on
the latest J7200 datasheet[2]
[1] - section 12.3.6.1.1 MMCSD Features, in
https://www.ti.com/lit/ug/spruiu1a/spruiu1a.pdf
[2] - https://www.ti.com/lit/ds/symlink/dra821a.pdf
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
---
.../dts/ti/k3-j7200-common-proc-board.dts | 42 +++++++++++++++++++
arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 14 ++++++-
2 files changed, 54 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
index b493f939b09a..6f90c3b1cf45 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
@@ -16,6 +16,29 @@
stdout-path = "serial2:115200n8";
bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
};
+
+ vdd_mmc1: fixedregulator-sd {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_mmc1";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ enable-active-high;
+ gpios = <&exp2 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ vdd_sd_dv: gpio-regulator-vdd-sd-dv {
+ compatible = "regulator-gpio";
+ regulator-name = "vdd_sd_dv";
+ pinctrl-names = "default";
+ pinctrl-0 = <&vdd_sd_dv_pins_default>;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ gpios = <&main_gpio0 55 GPIO_ACTIVE_HIGH>;
+ states = <1800000 0x0
+ 3300000 0x1>;
+ };
};
&wkup_pmx0 {
@@ -45,6 +68,13 @@
};
&main_pmx0 {
+ main_i2c0_pins_default: main-i2c0-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */
+ J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */
+ >;
+ };
+
main_i2c1_pins_default: main-i2c1-pins-default {
pinctrl-single,pins = <
J721E_IOPAD(0xdc, PIN_INPUT_PULLUP, 3) /* (U3) ECAP0_IN_APWM_OUT.I2C1_SCL */
@@ -70,6 +100,12 @@
J721E_IOPAD(0x120, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */
>;
};
+
+ vdd_sd_dv_pins_default: vdd_sd_dv_pins_default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0xd0, PIN_INPUT, 7) /* (T5) SPI0_D1.GPIO0_55 */
+ >;
+ };
};
&wkup_uart0 {
@@ -157,6 +193,10 @@
};
&main_i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c0_pins_default>;
+ clock-frequency = <400000>;
+
exp1: gpio@20 {
compatible = "ti,tca6416";
reg = <0x20>;
@@ -206,6 +246,8 @@
/* SD card */
pinctrl-0 = <&main_mmc1_pins_default>;
pinctrl-names = "default";
+ vmmc-supply = <&vdd_mmc1>;
+ vqmmc-supply = <&vdd_sd_dv>;
ti,driver-strength-ohm = <50>;
disable-wp;
};
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
index e60650a62b14..f86c493a44f1 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
@@ -512,11 +512,16 @@
ti,otap-del-sel-mmc-hs = <0x0>;
ti,otap-del-sel-ddr52 = <0x6>;
ti,otap-del-sel-hs200 = <0x8>;
- ti,otap-del-sel-hs400 = <0x0>;
+ ti,otap-del-sel-hs400 = <0x5>;
+ ti,itap-del-sel-legacy = <0x10>;
+ ti,itap-del-sel-mmc-hs = <0xa>;
ti,strobe-sel = <0x77>;
+ ti,clkbuf-sel = <0x7>;
ti,trm-icp = <0x8>;
bus-width = <8>;
mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ mmc-hs400-1_8v;
dma-coherent;
};
@@ -534,7 +539,12 @@
ti,otap-del-sel-sdr50 = <0xc>;
ti,otap-del-sel-sdr104 = <0x5>;
ti,otap-del-sel-ddr50 = <0xc>;
- no-1-8-v;
+ ti,itap-del-sel-legacy = <0x0>;
+ ti,itap-del-sel-sd-hs = <0x0>;
+ ti,itap-del-sel-sdr12 = <0x0>;
+ ti,itap-del-sel-sdr25 = <0x0>;
+ ti,clkbuf-sel = <0x7>;
+ ti,trm-icp = <0x8>;
dma-coherent;
};
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 8+ messages in thread
* Re: [PATCH v5 1/3] arm64: dts: ti: k3-j7200: Add gpio nodes
2021-03-10 16:19 ` [PATCH v5 1/3] arm64: dts: ti: k3-j7200: Add gpio nodes Aswath Govindraju
@ 2021-03-11 12:30 ` Grygorii Strashko
0 siblings, 0 replies; 8+ messages in thread
From: Grygorii Strashko @ 2021-03-11 12:30 UTC (permalink / raw)
To: Aswath Govindraju
Cc: Vignesh Raghavendra, Lokesh Vutla, Kishon Vijay Abraham I,
Faiz Abbas, Sekhar Nori, Nishanth Menon, Tero Kristo,
Rob Herring, linux-arm-kernel, devicetree, linux-kernel
On 10/03/2021 18:19, Aswath Govindraju wrote:
> From: Faiz Abbas <faiz_abbas@ti.com>
>
> There are 4 instances of gpio modules in main domain:
> gpio0, gpio2, gpio4 and gpio6
>
> Groups are created to provide protection between different processor
> virtual worlds. Each of these modules I/O pins are muxed within the
> group. Exactly one module can be selected to control the corresponding
> pin by selecting it in the pad mux configuration registers.
>
> This group in main domain pins out 69 lines (5 banks). Add DT modes for
> each module instance in the main domain.
>
> Similar to the gpio groups in main domain, there is one gpio group in
> wakeup domain with 2 module instances in it.
>
> The gpio group pins out 72 pins (6 banks) of the first 85 gpio lines. Add
> DT nodes for each module instance in the wakeup domain.
>
> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
> Signed-off-by: Sekhar Nori <nsekhar@ti.com>
> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
> ---
> arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 72 +++++++++++++++++++
> .../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi | 34 +++++++++
> 2 files changed, 106 insertions(+)
>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
--
Best regards,
grygorii
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v5 2/3] arm64: dts: ti: k3-j7200-common-proc-board: Disable unused gpio modules
2021-03-10 16:19 ` [PATCH v5 2/3] arm64: dts: ti: k3-j7200-common-proc-board: Disable unused gpio modules Aswath Govindraju
@ 2021-03-16 12:01 ` Grygorii Strashko
0 siblings, 0 replies; 8+ messages in thread
From: Grygorii Strashko @ 2021-03-16 12:01 UTC (permalink / raw)
To: Aswath Govindraju
Cc: Vignesh Raghavendra, Lokesh Vutla, Kishon Vijay Abraham I,
Faiz Abbas, Sekhar Nori, Nishanth Menon, Tero Kristo,
Rob Herring, linux-arm-kernel, devicetree, linux-kernel
On 10/03/2021 18:19, Aswath Govindraju wrote:
> From: Faiz Abbas <faiz_abbas@ti.com>
>
> There are 6 gpio instances inside SoC with 2 groups as show below:
> Group one: wkup_gpio0, wkup_gpio1
> Group two: main_gpio0, main_gpio2, main_gpio4, main_gpio6
>
> Only one instance from each group can be used at a time. So use main_gpio0
> and wkup_gpio0 in current linux context and disable the rest of the nodes.
>
> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
> Signed-off-by: Sekhar Nori <nsekhar@ti.com>
> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
> ---
> .../boot/dts/ti/k3-j7200-common-proc-board.dts | 16 ++++++++++++++++
> 1 file changed, 16 insertions(+)
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
--
Best regards,
grygorii
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v5 3/3] arm64: dts: ti: k3-j7200: Add support for higher speed modes and update delay select values for MMCSD subsystems
2021-03-10 16:19 ` [PATCH v5 3/3] arm64: dts: ti: k3-j7200: Add support for higher speed modes and update delay select values for MMCSD subsystems Aswath Govindraju
@ 2021-03-18 15:15 ` Kishon Vijay Abraham I
2021-03-19 3:45 ` Aswath Govindraju
0 siblings, 1 reply; 8+ messages in thread
From: Kishon Vijay Abraham I @ 2021-03-18 15:15 UTC (permalink / raw)
To: Aswath Govindraju
Cc: Vignesh Raghavendra, Lokesh Vutla, Nishanth Menon, Tero Kristo,
Rob Herring, linux-arm-kernel, devicetree, linux-kernel
Hi,
On 10/03/21 9:49 pm, Aswath Govindraju wrote:
> The following speed modes are now supported in J7200 SoC,
> - HS200 and HS400 modes at 1.8 V card voltage, in MMCSD0 subsystem [1].
> - UHS-I speed modes in MMCSD1 subsystem [1].
>
> Add support for UHS-I modes by adding voltage regulator device tree nodes
> and corresponding pinmux details, to power cycle and voltage switch cards.
> Set respective tags in sdhci0 and remove no-1-8-v tag from sdhci1
> device tree nodes.
>
> Also update the delay values for various speed modes supported, based on
> the latest J7200 datasheet[2]
nit: Better to mention the datasheet version (as it's not latest anymore).
>
> [1] - section 12.3.6.1.1 MMCSD Features, in
> https://www.ti.com/lit/ug/spruiu1a/spruiu1a.pdf
>
> [2] - https://www.ti.com/lit/ds/symlink/dra821a.pdf
Er.. this link is already broken.
Thanks
Kishon
>
> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
> ---
> .../dts/ti/k3-j7200-common-proc-board.dts | 42 +++++++++++++++++++
> arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 14 ++++++-
> 2 files changed, 54 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> index b493f939b09a..6f90c3b1cf45 100644
> --- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> +++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> @@ -16,6 +16,29 @@
> stdout-path = "serial2:115200n8";
> bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
> };
> +
> + vdd_mmc1: fixedregulator-sd {
> + compatible = "regulator-fixed";
> + regulator-name = "vdd_mmc1";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + enable-active-high;
> + gpios = <&exp2 2 GPIO_ACTIVE_HIGH>;
> + };
> +
> + vdd_sd_dv: gpio-regulator-vdd-sd-dv {
> + compatible = "regulator-gpio";
> + regulator-name = "vdd_sd_dv";
> + pinctrl-names = "default";
> + pinctrl-0 = <&vdd_sd_dv_pins_default>;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + gpios = <&main_gpio0 55 GPIO_ACTIVE_HIGH>;
> + states = <1800000 0x0
> + 3300000 0x1>;
> + };
> };
>
> &wkup_pmx0 {
> @@ -45,6 +68,13 @@
> };
>
> &main_pmx0 {
> + main_i2c0_pins_default: main-i2c0-pins-default {
> + pinctrl-single,pins = <
> + J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */
> + J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */
> + >;
> + };
> +
> main_i2c1_pins_default: main-i2c1-pins-default {
> pinctrl-single,pins = <
> J721E_IOPAD(0xdc, PIN_INPUT_PULLUP, 3) /* (U3) ECAP0_IN_APWM_OUT.I2C1_SCL */
> @@ -70,6 +100,12 @@
> J721E_IOPAD(0x120, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */
> >;
> };
> +
> + vdd_sd_dv_pins_default: vdd_sd_dv_pins_default {
> + pinctrl-single,pins = <
> + J721E_IOPAD(0xd0, PIN_INPUT, 7) /* (T5) SPI0_D1.GPIO0_55 */
> + >;
> + };
> };
>
> &wkup_uart0 {
> @@ -157,6 +193,10 @@
> };
>
> &main_i2c0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_i2c0_pins_default>;
> + clock-frequency = <400000>;
> +
> exp1: gpio@20 {
> compatible = "ti,tca6416";
> reg = <0x20>;
> @@ -206,6 +246,8 @@
> /* SD card */
> pinctrl-0 = <&main_mmc1_pins_default>;
> pinctrl-names = "default";
> + vmmc-supply = <&vdd_mmc1>;
> + vqmmc-supply = <&vdd_sd_dv>;
> ti,driver-strength-ohm = <50>;
> disable-wp;
> };
> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
> index e60650a62b14..f86c493a44f1 100644
> --- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
> @@ -512,11 +512,16 @@
> ti,otap-del-sel-mmc-hs = <0x0>;
> ti,otap-del-sel-ddr52 = <0x6>;
> ti,otap-del-sel-hs200 = <0x8>;
> - ti,otap-del-sel-hs400 = <0x0>;
> + ti,otap-del-sel-hs400 = <0x5>;
> + ti,itap-del-sel-legacy = <0x10>;
> + ti,itap-del-sel-mmc-hs = <0xa>;
> ti,strobe-sel = <0x77>;
> + ti,clkbuf-sel = <0x7>;
> ti,trm-icp = <0x8>;
> bus-width = <8>;
> mmc-ddr-1_8v;
> + mmc-hs200-1_8v;
> + mmc-hs400-1_8v;
> dma-coherent;
> };
>
> @@ -534,7 +539,12 @@
> ti,otap-del-sel-sdr50 = <0xc>;
> ti,otap-del-sel-sdr104 = <0x5>;
> ti,otap-del-sel-ddr50 = <0xc>;
> - no-1-8-v;
> + ti,itap-del-sel-legacy = <0x0>;
> + ti,itap-del-sel-sd-hs = <0x0>;
> + ti,itap-del-sel-sdr12 = <0x0>;
> + ti,itap-del-sel-sdr25 = <0x0>;
> + ti,clkbuf-sel = <0x7>;
> + ti,trm-icp = <0x8>;
> dma-coherent;
> };
>
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v5 3/3] arm64: dts: ti: k3-j7200: Add support for higher speed modes and update delay select values for MMCSD subsystems
2021-03-18 15:15 ` Kishon Vijay Abraham I
@ 2021-03-19 3:45 ` Aswath Govindraju
0 siblings, 0 replies; 8+ messages in thread
From: Aswath Govindraju @ 2021-03-19 3:45 UTC (permalink / raw)
To: Kishon Vijay Abraham I
Cc: Vignesh Raghavendra, Lokesh Vutla, Nishanth Menon, Tero Kristo,
Rob Herring, linux-arm-kernel, devicetree, linux-kernel
Hi Kishon,
On 18/03/21 8:45 pm, Kishon Vijay Abraham I wrote:
> Hi,
>
> On 10/03/21 9:49 pm, Aswath Govindraju wrote:
>> The following speed modes are now supported in J7200 SoC,
>> - HS200 and HS400 modes at 1.8 V card voltage, in MMCSD0 subsystem [1].
>> - UHS-I speed modes in MMCSD1 subsystem [1].
>>
>> Add support for UHS-I modes by adding voltage regulator device tree nodes
>> and corresponding pinmux details, to power cycle and voltage switch cards.
>> Set respective tags in sdhci0 and remove no-1-8-v tag from sdhci1
>> device tree nodes.
>>
>> Also update the delay values for various speed modes supported, based on
>> the latest J7200 datasheet[2]
>
> nit: Better to mention the datasheet version (as it's not latest anymore).
>>
>> [1] - section 12.3.6.1.1 MMCSD Features, in
>> https://www.ti.com/lit/ug/spruiu1a/spruiu1a.pdf
>>
>> [2] - https://www.ti.com/lit/ds/symlink/dra821a.pdf
> > Er.. this link is already broken.
>
Sorry, fixed this and added the version information for references in
the respin(v6) of this series.
Thank you for the comments.
Regards,
Aswath
> Thanks
> Kishon
>>
>> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
>> ---
>> .../dts/ti/k3-j7200-common-proc-board.dts | 42 +++++++++++++++++++
>> arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 14 ++++++-
>> 2 files changed, 54 insertions(+), 2 deletions(-)
>>
>> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
>> index b493f939b09a..6f90c3b1cf45 100644
>> --- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
>> +++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
>> @@ -16,6 +16,29 @@
>> stdout-path = "serial2:115200n8";
>> bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
>> };
>> +
>> + vdd_mmc1: fixedregulator-sd {
>> + compatible = "regulator-fixed";
>> + regulator-name = "vdd_mmc1";
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-boot-on;
>> + enable-active-high;
>> + gpios = <&exp2 2 GPIO_ACTIVE_HIGH>;
>> + };
>> +
>> + vdd_sd_dv: gpio-regulator-vdd-sd-dv {
>> + compatible = "regulator-gpio";
>> + regulator-name = "vdd_sd_dv";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&vdd_sd_dv_pins_default>;
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-boot-on;
>> + gpios = <&main_gpio0 55 GPIO_ACTIVE_HIGH>;
>> + states = <1800000 0x0
>> + 3300000 0x1>;
>> + };
>> };
>>
>> &wkup_pmx0 {
>> @@ -45,6 +68,13 @@
>> };
>>
>> &main_pmx0 {
>> + main_i2c0_pins_default: main-i2c0-pins-default {
>> + pinctrl-single,pins = <
>> + J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */
>> + J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */
>> + >;
>> + };
>> +
>> main_i2c1_pins_default: main-i2c1-pins-default {
>> pinctrl-single,pins = <
>> J721E_IOPAD(0xdc, PIN_INPUT_PULLUP, 3) /* (U3) ECAP0_IN_APWM_OUT.I2C1_SCL */
>> @@ -70,6 +100,12 @@
>> J721E_IOPAD(0x120, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */
>> >;
>> };
>> +
>> + vdd_sd_dv_pins_default: vdd_sd_dv_pins_default {
>> + pinctrl-single,pins = <
>> + J721E_IOPAD(0xd0, PIN_INPUT, 7) /* (T5) SPI0_D1.GPIO0_55 */
>> + >;
>> + };
>> };
>>
>> &wkup_uart0 {
>> @@ -157,6 +193,10 @@
>> };
>>
>> &main_i2c0 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&main_i2c0_pins_default>;
>> + clock-frequency = <400000>;
>> +
>> exp1: gpio@20 {
>> compatible = "ti,tca6416";
>> reg = <0x20>;
>> @@ -206,6 +246,8 @@
>> /* SD card */
>> pinctrl-0 = <&main_mmc1_pins_default>;
>> pinctrl-names = "default";
>> + vmmc-supply = <&vdd_mmc1>;
>> + vqmmc-supply = <&vdd_sd_dv>;
>> ti,driver-strength-ohm = <50>;
>> disable-wp;
>> };
>> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
>> index e60650a62b14..f86c493a44f1 100644
>> --- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
>> +++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
>> @@ -512,11 +512,16 @@
>> ti,otap-del-sel-mmc-hs = <0x0>;
>> ti,otap-del-sel-ddr52 = <0x6>;
>> ti,otap-del-sel-hs200 = <0x8>;
>> - ti,otap-del-sel-hs400 = <0x0>;
>> + ti,otap-del-sel-hs400 = <0x5>;
>> + ti,itap-del-sel-legacy = <0x10>;
>> + ti,itap-del-sel-mmc-hs = <0xa>;
>> ti,strobe-sel = <0x77>;
>> + ti,clkbuf-sel = <0x7>;
>> ti,trm-icp = <0x8>;
>> bus-width = <8>;
>> mmc-ddr-1_8v;
>> + mmc-hs200-1_8v;
>> + mmc-hs400-1_8v;
>> dma-coherent;
>> };
>>
>> @@ -534,7 +539,12 @@
>> ti,otap-del-sel-sdr50 = <0xc>;
>> ti,otap-del-sel-sdr104 = <0x5>;
>> ti,otap-del-sel-ddr50 = <0xc>;
>> - no-1-8-v;
>> + ti,itap-del-sel-legacy = <0x0>;
>> + ti,itap-del-sel-sd-hs = <0x0>;
>> + ti,itap-del-sel-sdr12 = <0x0>;
>> + ti,itap-del-sel-sdr25 = <0x0>;
>> + ti,clkbuf-sel = <0x7>;
>> + ti,trm-icp = <0x8>;
>> dma-coherent;
>> };
>>
>>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2021-03-19 3:47 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-03-10 16:19 [PATCH v5 0/3] J7200: Add support for GPIO and higher speed modes in MMCSD subsystems Aswath Govindraju
2021-03-10 16:19 ` [PATCH v5 1/3] arm64: dts: ti: k3-j7200: Add gpio nodes Aswath Govindraju
2021-03-11 12:30 ` Grygorii Strashko
2021-03-10 16:19 ` [PATCH v5 2/3] arm64: dts: ti: k3-j7200-common-proc-board: Disable unused gpio modules Aswath Govindraju
2021-03-16 12:01 ` Grygorii Strashko
2021-03-10 16:19 ` [PATCH v5 3/3] arm64: dts: ti: k3-j7200: Add support for higher speed modes and update delay select values for MMCSD subsystems Aswath Govindraju
2021-03-18 15:15 ` Kishon Vijay Abraham I
2021-03-19 3:45 ` Aswath Govindraju
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).