From: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
To: Sean Wang <sean.wang@mediatek.com>,
Landen Chao <Landen.Chao@mediatek.com>,
Andrew Lunn <andrew@lunn.ch>,
Vivien Didelot <vivien.didelot@gmail.com>,
Florian Fainelli <f.fainelli@gmail.com>,
Vladimir Oltean <olteanv@gmail.com>,
"David S. Miller" <davem@davemloft.net>,
Jakub Kicinski <kuba@kernel.org>,
Matthias Brugger <matthias.bgg@gmail.com>,
Philipp Zabel <p.zabel@pengutronix.de>,
Russell King <linux@armlinux.org.uk>,
netdev@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-mediatek@lists.infradead.org, linux-kernel@vger.kernel.org,
sander@svanheule.net, tsbogend@alpha.franken.de,
john@phrozen.org
Cc: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Subject: [PATCH net, v2] net: dsa: mt7530: setup core clock even in TRGMII mode
Date: Fri, 12 Mar 2021 00:07:03 -0800 [thread overview]
Message-ID: <20210312080703.63281-1-ilya.lipnitskiy@gmail.com> (raw)
In-Reply-To: <20210311012108.7190-1-ilya.lipnitskiy@gmail.com>
A recent change to MIPS ralink reset logic made it so mt7530 actually
resets the switch on platforms such as mt7621 (where bit 2 is the reset
line for the switch). That exposed an issue where the switch would not
function properly in TRGMII mode after a reset.
Reconfigure core clock in TRGMII mode to fix the issue.
Tested on Ubiquiti ER-X (MT7621) with TRGMII mode enabled.
Fixes: 3f9ef7785a9c ("MIPS: ralink: manage low reset lines")
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
---
drivers/net/dsa/mt7530.c | 52 +++++++++++++++++++---------------------
1 file changed, 25 insertions(+), 27 deletions(-)
diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index f06f5fa2f898..9871d7cff93a 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -436,34 +436,32 @@ mt7530_pad_clk_setup(struct dsa_switch *ds, phy_interface_t interface)
TD_DM_DRVP(8) | TD_DM_DRVN(8));
/* Setup core clock for MT7530 */
- if (!trgint) {
- /* Disable MT7530 core clock */
- core_clear(priv, CORE_TRGMII_GSW_CLK_CG, REG_GSWCK_EN);
-
- /* Disable PLL, since phy_device has not yet been created
- * provided for phy_[read,write]_mmd_indirect is called, we
- * provide our own core_write_mmd_indirect to complete this
- * function.
- */
- core_write_mmd_indirect(priv,
- CORE_GSWPLL_GRP1,
- MDIO_MMD_VEND2,
- 0);
-
- /* Set core clock into 500Mhz */
- core_write(priv, CORE_GSWPLL_GRP2,
- RG_GSWPLL_POSDIV_500M(1) |
- RG_GSWPLL_FBKDIV_500M(25));
+ /* Disable MT7530 core clock */
+ core_clear(priv, CORE_TRGMII_GSW_CLK_CG, REG_GSWCK_EN);
- /* Enable PLL */
- core_write(priv, CORE_GSWPLL_GRP1,
- RG_GSWPLL_EN_PRE |
- RG_GSWPLL_POSDIV_200M(2) |
- RG_GSWPLL_FBKDIV_200M(32));
-
- /* Enable MT7530 core clock */
- core_set(priv, CORE_TRGMII_GSW_CLK_CG, REG_GSWCK_EN);
- }
+ /* Disable PLL, since phy_device has not yet been created
+ * provided for phy_[read,write]_mmd_indirect is called, we
+ * provide our own core_write_mmd_indirect to complete this
+ * function.
+ */
+ core_write_mmd_indirect(priv,
+ CORE_GSWPLL_GRP1,
+ MDIO_MMD_VEND2,
+ 0);
+
+ /* Set core clock into 500Mhz */
+ core_write(priv, CORE_GSWPLL_GRP2,
+ RG_GSWPLL_POSDIV_500M(1) |
+ RG_GSWPLL_FBKDIV_500M(25));
+
+ /* Enable PLL */
+ core_write(priv, CORE_GSWPLL_GRP1,
+ RG_GSWPLL_EN_PRE |
+ RG_GSWPLL_POSDIV_200M(2) |
+ RG_GSWPLL_FBKDIV_200M(32));
+
+ /* Enable MT7530 core clock */
+ core_set(priv, CORE_TRGMII_GSW_CLK_CG, REG_GSWCK_EN);
/* Setup the MT7530 TRGMII Tx Clock */
core_set(priv, CORE_TRGMII_GSW_CLK_CG, REG_GSWCK_EN);
--
2.30.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2021-03-12 8:09 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-03-11 1:21 [PATCH net] net: dsa: mt7530: setup core clock even in TRGMII mode Ilya Lipnitskiy
2021-03-11 3:21 ` Florian Fainelli
2021-03-12 8:07 ` Ilya Lipnitskiy [this message]
2021-03-19 10:25 ` [PATCH net,v2] " René van Dorst
2021-03-19 12:47 ` Aw: " Frank Wunderlich
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210312080703.63281-1-ilya.lipnitskiy@gmail.com \
--to=ilya.lipnitskiy@gmail.com \
--cc=Landen.Chao@mediatek.com \
--cc=andrew@lunn.ch \
--cc=davem@davemloft.net \
--cc=f.fainelli@gmail.com \
--cc=john@phrozen.org \
--cc=kuba@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mediatek@lists.infradead.org \
--cc=linux@armlinux.org.uk \
--cc=matthias.bgg@gmail.com \
--cc=netdev@vger.kernel.org \
--cc=olteanv@gmail.com \
--cc=p.zabel@pengutronix.de \
--cc=sander@svanheule.net \
--cc=sean.wang@mediatek.com \
--cc=tsbogend@alpha.franken.de \
--cc=vivien.didelot@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).