From: Ivan Uvarov <i.uvarov@cognitivepilot.com>
To: devicetree@vger.kernel.org
Cc: Chen-Yu Tsai <wens@csie.org>,
Jernej Skrabec <jernej.skrabec@siol.net>,
Maxime Ripard <mripard@kernel.org>,
Rob Herring <robh+dt@kernel.org>,
linux-arm-kernel@lists.infradead.org,
Andre Przywara <andre.przywara@arm.com>,
Icenowy Zheng <icenowy@aosc.io>,
Ivan Uvarov <i.uvarov@cognitivepilot.com>
Subject: [PATCH v4 2/5] ARM: dts: sun8i: r40: add pinmux settings for MMC3 and UARTs 2, 4, 5&7
Date: Wed, 7 Apr 2021 14:14:25 +0300 [thread overview]
Message-ID: <20210407111428.3755684-3-i.uvarov@cognitivepilot.com> (raw)
In-Reply-To: <20210407111428.3755684-1-i.uvarov@cognitivepilot.com>
The Forlinx OKA40i-C devboard makes use of UARTs 0,2,3,4,5 and 7 of the R40
SoC, of which UART 0 is connected to an RS232 converter, UART 5 routed to
an RS485 converter, and the rest broken out directly via labeled headers.
The board also contains a micro-SD slot connected to SDC3.
This patch adds settings to R40's pinmux node for MMC3 and those UARTs that
were not already mapped, which would allow us to make use of all available
UARTs and the micro-SD slot on this board in a further patch.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Ivan Uvarov <i.uvarov@cognitivepilot.com>
1 file changed, 41 insertions(+)
diff --git a/arch/arm/boot/dts/sun8i-r40.dtsi b/arch/arm/boot/dts/sun8i-r40.dtsi
index 0b257a0779..9ad4f0129c 100644
--- a/arch/arm/boot/dts/sun8i-r40.dtsi
+++ b/arch/arm/boot/dts/sun8i-r40.dtsi
@@ -357,6 +357,8 @@ mmc3: mmc@1c12000 {
clock-names = "ahb", "mmc";
resets = <&ccu RST_BUS_MMC3>;
reset-names = "ahb";
+ pinctrl-0 = <&mmc3_pins>;
+ pinctrl-names = "default";
interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
#address-cells = <1>;
@@ -601,6 +603,15 @@ mmc2_pins: mmc2-pins {
bias-pull-up;
};
+ /omit-if-no-ref/
+ mmc3_pins: mmc3-pins {
+ pins = "PI4", "PI5", "PI6",
+ "PI7", "PI8", "PI9";
+ function = "mmc3";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
/omit-if-no-ref/
spi0_pc_pins: spi0-pc-pins {
pins = "PC0", "PC1", "PC2";
@@ -637,6 +648,18 @@ uart0_pb_pins: uart0-pb-pins {
function = "uart0";
};
+ /omit-if-no-ref/
+ uart2_pi_pins: uart2-pi-pins {
+ pins = "PI18", "PI19";
+ function = "uart2";
+ };
+
+ /omit-if-no-ref/
+ uart2_rts_cts_pi_pins: uart2-rts-cts-pi-pins{
+ pins = "PI16", "PI17";
+ function = "uart2";
+ };
+
/omit-if-no-ref/
uart3_pg_pins: uart3-pg-pins {
pins = "PG6", "PG7";
@@ -648,6 +671,24 @@ uart3_rts_cts_pg_pins: uart3-rts-cts-pg-pins {
pins = "PG8", "PG9";
function = "uart3";
};
+
+ /omit-if-no-ref/
+ uart4_pg_pins: uart4-pg-pins {
+ pins = "PG10", "PG11";
+ function = "uart4";
+ };
+
+ /omit-if-no-ref/
+ uart5_ph_pins: uart5-ph-pins {
+ pins = "PH6", "PH7";
+ function = "uart5";
+ };
+
+ /omit-if-no-ref/
+ uart7_pi_pins: uart7-pi-pins {
+ pins = "PI20", "PI21";
+ function = "uart7";
+ };
};
wdt: watchdog@1c20c90 {
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2021-04-07 11:18 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-04-07 11:14 [PATCH v4 0/5] add devicetree for Forlinx FETA40i-C & OKA40i-C Ivan Uvarov
2021-04-07 11:14 ` [PATCH v4 1/5] ARM: dts: sun8i: r40: add /omit-if-no-ref/ to pinmux nodes for UARTs 0&3 Ivan Uvarov
2021-04-07 11:14 ` Ivan Uvarov [this message]
2021-04-07 11:14 ` [PATCH v4 3/5] dt-bindings: add compatible vendor prefix for Forlinx Ivan Uvarov
2021-04-08 20:14 ` Rob Herring
2021-04-07 11:14 ` [PATCH v4 4/5] dt-bindings: arm: add compatible for Forlinx OKA40i-C and FETA40i-C Ivan Uvarov
2021-04-08 20:14 ` Rob Herring
2021-04-07 11:14 ` [PATCH v4 5/5] ARM: dts: sun8i: r40: add devicetree for Forlinx FETA40i-C & OKA40i-C Ivan Uvarov
2021-04-15 8:08 ` [PATCH v4 0/5] " Maxime Ripard
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210407111428.3755684-3-i.uvarov@cognitivepilot.com \
--to=i.uvarov@cognitivepilot.com \
--cc=andre.przywara@arm.com \
--cc=devicetree@vger.kernel.org \
--cc=icenowy@aosc.io \
--cc=jernej.skrabec@siol.net \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=mripard@kernel.org \
--cc=robh+dt@kernel.org \
--cc=wens@csie.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).