From: Claudiu Beznea <claudiu.beznea@microchip.com>
To: <nicolas.ferre@microchip.com>, <alexandre.belloni@bootlin.com>,
<ludovic.desroches@microchip.com>, <robh+dt@kernel.org>,
<linux@armlinux.org.uk>
Cc: <linux-arm-kernel@lists.infradead.org>,
<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
Claudiu Beznea <claudiu.beznea@microchip.com>
Subject: [PATCH v3 11/24] ARM: at91: ddr: add registers definitions for sama7g5's ddr
Date: Thu, 15 Apr 2021 13:49:57 +0300 [thread overview]
Message-ID: <20210415105010.569620-12-claudiu.beznea@microchip.com> (raw)
In-Reply-To: <20210415105010.569620-1-claudiu.beznea@microchip.com>
Add registers and bits definitions for SAMA7G5's UDDRC and DDR3PHY.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
---
include/soc/at91/sama7-ddr.h | 80 ++++++++++++++++++++++++++++++++++++
1 file changed, 80 insertions(+)
create mode 100644 include/soc/at91/sama7-ddr.h
diff --git a/include/soc/at91/sama7-ddr.h b/include/soc/at91/sama7-ddr.h
new file mode 100644
index 000000000000..f6542584ca13
--- /dev/null
+++ b/include/soc/at91/sama7-ddr.h
@@ -0,0 +1,80 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Microchip SAMA7 UDDR Controller and DDR3 PHY Controller registers offsets
+ * and bit definitions.
+ *
+ * Copyright (C) [2020] Microchip Technology Inc. and its subsidiaries
+ *
+ * Author: Claudu Beznea <claudiu.beznea@microchip.com>
+ */
+
+#ifndef __SAMA7_DDR_H__
+#define __SAMA7_DDR_H__
+
+#ifdef CONFIG_SOC_SAMA7
+
+/* DDR3PHY */
+#define DDR3PHY_PIR (0x04) /* DDR3PHY PHY Initialization Register */
+#define DDR3PHY_PIR_DLLBYP (1 << 17) /* DLL Bypass */
+#define DDR3PHY_PIR_ITMSRST (1 << 4) /* Interface Timing Module Soft Reset */
+#define DDR3PHY_PIR_DLLLOCK (1 << 2) /* DLL Lock */
+#define DDR3PHY_PIR_DLLSRST (1 << 1) /* DLL Soft Rest */
+#define DDR3PHY_PIR_INIT (1 << 0) /* Initialization Trigger */
+
+#define DDR3PHY_PGCR (0x08) /* DDR3PHY PHY General Configuration Register */
+#define DDR3PHY_PGCR_CKDV1 (1 << 13) /* CK# Disable Value */
+#define DDR3PHY_PGCR_CKDV0 (1 << 12) /* CK Disable Value */
+
+#define DDR3PHY_PGSR (0x0C) /* DDR3PHY PHY General Status Register */
+#define DDR3PHY_PGSR_IDONE (1 << 0) /* Initialization Done */
+
+#define DDR3PHY_ACIOCR (0x24) /* DDR3PHY AC I/O Configuration Register */
+#define DDR3PHY_ACIOCR_CSPDD_CS0 (1 << 18) /* CS#[0] Power Down Driver */
+#define DDR3PHY_ACIOCR_CKPDD_CK0 (1 << 8) /* CK[0] Power Down Driver */
+#define DDR3PHY_ACIORC_ACPDD (1 << 3) /* AC Power Down Driver */
+
+#define DDR3PHY_DXCCR (0x28) /* DDR3PHY DATX8 Common Configuration Register */
+#define DDR3PHY_DXCCR_DXPDR (1 << 3) /* Data Power Down Receiver */
+
+#define DDR3PHY_DSGCR (0x2C) /* DDR3PHY DDR System General Configuration Register */
+#define DDR3PHY_DSGCR_ODTPDD_ODT0 (1 << 20) /* ODT[0] Power Down Driver */
+
+#define DDR3PHY_ZQ0SR0 (0x188) /* ZQ status register 0 */
+
+/* UDDRC */
+#define UDDRC_STAT (0x04) /* UDDRC Operating Mode Status Register */
+#define UDDRC_STAT_SELFREF_TYPE_DIS (0x0 << 4) /* SDRAM is not in Self-refresh */
+#define UDDRC_STAT_SELFREF_TYPE_PHY (0x1 << 4) /* SDRAM is in Self-refresh, which was caused by PHY Master Request */
+#define UDDRC_STAT_SELFREF_TYPE_SW (0x2 << 4) /* SDRAM is in Self-refresh, which was not caused solely under Automatic Self-refresh control */
+#define UDDRC_STAT_SELFREF_TYPE_AUTO (0x3 << 4) /* SDRAM is in Self-refresh, which was caused by Automatic Self-refresh only */
+#define UDDRC_STAT_SELFREF_TYPE_MSK (0x3 << 4) /* Self-refresh type mask */
+#define UDDRC_STAT_OPMODE_INIT (0x0 << 0) /* Init */
+#define UDDRC_STAT_OPMODE_NORMAL (0x1 << 0) /* Normal */
+#define UDDRC_STAT_OPMODE_PWRDOWN (0x2 << 0) /* Power-down */
+#define UDDRC_STAT_OPMODE_SELF_REFRESH (0x3 << 0) /* Self-refresh */
+#define UDDRC_STAT_OPMODE_MSK (0x7 << 0) /* Operating mode mask */
+
+#define UDDRC_PWRCTL (0x30) /* UDDRC Low Power Control Register */
+#define UDDRC_PWRCTRL_SELFREF_SW (1 << 5) /* Software self-refresh */
+
+#define UDDRC_DFIMISC (0x1B0) /* UDDRC DFI Miscellaneous Control Register */
+#define UDDRC_DFIMISC_DFI_INIT_COMPLETE_EN (1 << 0) /* PHY initialization complete enable signal */
+
+#define UDDRC_SWCTRL (0x320) /* UDDRC Software Register Programming Control Enable */
+#define UDDRC_SWCTRL_SW_DONE (1 << 0) /* Enable quasi-dynamic register programming outside reset */
+
+#define UDDRC_SWSTAT (0x324) /* UDDRC Software Register Programming Control Status */
+#define UDDRC_SWSTAT_SW_DONE_ACK (1 << 0) /* Register programming done */
+
+#define UDDRC_PSTAT (0x3FC) /* UDDRC Port Status Register */
+#define UDDRC_PSTAT_ALL_PORTS (0x1F001F) /* Read + writes outstanding transactions on all ports */
+
+#define UDDRC_PCTRL_0 (0x490) /* UDDRC Port 0 Control Register */
+#define UDDRC_PCTRL_1 (0x540) /* UDDRC Port 1 Control Register */
+#define UDDRC_PCTRL_2 (0x5F0) /* UDDRC Port 2 Control Register */
+#define UDDRC_PCTRL_3 (0x6A0) /* UDDRC Port 3 Control Register */
+#define UDDRC_PCTRL_4 (0x750) /* UDDRC Port 4 Control Register */
+
+#endif /* CONFIG_SOC_SAMA7 */
+
+#endif /* __SAMA7_DDR_H__ */
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2021-04-15 10:56 UTC|newest]
Thread overview: 27+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-04-15 10:49 [PATCH v3 00/24] ARM: at91: pm: add support for sama7g5 Claudiu Beznea
2021-04-15 10:49 ` [PATCH v3 01/24] ARM: at91: pm: move pm_bu to soc_pm data structure Claudiu Beznea
2021-04-15 10:49 ` [PATCH v3 02/24] ARM: at91: pm: move the setup of soc_pm.bu->suspended Claudiu Beznea
2021-04-15 10:49 ` [PATCH v3 03/24] ARM: at91: pm: document at91_soc_pm structure Claudiu Beznea
2021-04-15 10:49 ` [PATCH v3 04/24] ARM: at91: pm: check for different controllers in at91_pm_modes_init() Claudiu Beznea
2021-04-15 10:49 ` [PATCH v3 05/24] ARM: at91: pm: do not initialize pdev Claudiu Beznea
2021-04-15 10:49 ` [PATCH v3 06/24] ARM: at91: pm: use r7 instead of tmp1 Claudiu Beznea
2021-04-15 10:49 ` [PATCH v3 07/24] ARM: at91: pm: avoid push and pop on stack while memory is in self-refersh Claudiu Beznea
2021-04-15 10:49 ` [PATCH v3 08/24] ARM: at91: pm: s/CONFIG_SOC_SAM9X60/CONFIG_HAVE_AT91_SAM9X60_PLL/g Claudiu Beznea
2021-04-15 10:49 ` [PATCH v3 09/24] ARM: at91: pm: add support for waiting MCK1..4 Claudiu Beznea
2021-04-15 10:49 ` [PATCH v3 10/24] ARM: at91: sfrbu: add sfrbu registers definitions for sama7g5 Claudiu Beznea
2021-04-15 10:49 ` Claudiu Beznea [this message]
2021-04-15 10:49 ` [PATCH v3 12/24] ARM: at91: pm: add self-refresh support " Claudiu Beznea
2021-04-15 10:49 ` [PATCH v3 13/24] ARM: at91: pm: add support for MCK1..4 save/restore for ulp modes Claudiu Beznea
2021-04-15 10:50 ` [PATCH v3 14/24] ARM: at91: pm: add support for 2.5V LDO regulator control Claudiu Beznea
2021-04-15 10:50 ` [PATCH v3 15/24] ARM: at91: pm: wait for ddr power mode off Claudiu Beznea
2021-04-15 10:50 ` [PATCH v3 16/24] dt-bindings: atmel-sysreg: add bindings for sama7g5 Claudiu Beznea
2021-04-15 20:59 ` Rob Herring
2021-04-15 10:50 ` [PATCH v3 17/24] ARM: at91: pm: add sama7g5 ddr controller Claudiu Beznea
2021-04-15 10:50 ` [PATCH v3 18/24] ARM: at91: pm: add sama7g5 ddr phy controller Claudiu Beznea
2021-04-15 10:50 ` [PATCH v3 19/24] ARM: at91: pm: save ddr phy calibration data to securam Claudiu Beznea
2021-04-15 10:50 ` [PATCH v3 20/24] ARM: at91: pm: add backup mode support for SAMA7G5 Claudiu Beznea
2021-04-15 10:50 ` [PATCH v3 21/24] ARM: at91: pm: add sama7g5's pmc Claudiu Beznea
2021-04-15 10:50 ` [PATCH v3 22/24] ARM: at91: sama7: introduce sama7 SoC family Claudiu Beznea
2021-04-15 10:50 ` [PATCH v3 23/24] ARM: at91: pm: add pm support for SAMA7G5 Claudiu Beznea
2021-04-15 10:50 ` [PATCH v3 24/24] ARM: at91: pm: add sama7g5 shdwc Claudiu Beznea
2021-07-16 18:03 ` [PATCH v3 00/24] ARM: at91: pm: add support for sama7g5 Nicolas Ferre
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210415105010.569620-12-claudiu.beznea@microchip.com \
--to=claudiu.beznea@microchip.com \
--cc=alexandre.belloni@bootlin.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@armlinux.org.uk \
--cc=ludovic.desroches@microchip.com \
--cc=nicolas.ferre@microchip.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).