linux-arm-kernel.lists.infradead.org archive mirror
 help / color / mirror / Atom feed
From: Boris Brezillon <boris.brezillon@collabora.com>
To: <patrice.chotard@foss.st.com>
Cc: Mark Brown <broonie@kernel.org>,
	Miquel Raynal <miquel.raynal@bootlin.com>,
	Vignesh Raghavendra <vigneshr@ti.com>,
	<linux-mtd@lists.infradead.org>,
	Alexandre Torgue <alexandre.torgue@foss.st.com>,
	<linux-spi@vger.kernel.org>,
	<linux-stm32@st-md-mailman.stormreply.com>,
	<linux-arm-kernel@lists.infradead.org>,
	<linux-kernel@vger.kernel.org>, <christophe.kerello@foss.st.com>
Subject: Re: [PATCH v3 1/3] spi: spi-mem: add automatic poll status functions
Date: Tue, 18 May 2021 13:30:54 +0200	[thread overview]
Message-ID: <20210518133054.3240b088@collabora.com> (raw)
In-Reply-To: <20210518093951.23136-2-patrice.chotard@foss.st.com>

On Tue, 18 May 2021 11:39:49 +0200
<patrice.chotard@foss.st.com> wrote:

> From: Patrice Chotard <patrice.chotard@foss.st.com>
> 
> With STM32 QSPI, it is possible to poll the status register of the device.
> This could be done to offload the CPU during an operation (erase or
> program a SPI NAND for example).
> 
> spi_mem_poll_status API has been added to handle this feature.
> This new function take care of the offload/non-offload cases.
> 
> For the non-offload case, use read_poll_timeout() to poll the status in
> order to release CPU during this phase.
> For example, previously, when erasing large area, in non-offload case,
> CPU load can reach ~50%, now it decrease to ~35%.
> 
> Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
> Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
> ---
> Changes in v3:
>   - Add spi_mem_read_status() which allows to read 8 or 16 bits status.
>   - Add initial_delay_us and polling_delay_us parameters to spi_mem_poll_status()
>     and also to poll_status() callback.
>   - Move spi_mem_supports_op() in SW-based polling case.
>   - Add delay before invoking read_poll_timeout().
>   - Remove the reinit/wait_for_completion() added in v2.
> 
> Changes in v2:
>   - Indicates the spi_mem_poll_status() timeout unit
>   - Use 2-byte wide status register
>   - Add spi_mem_supports_op() call in spi_mem_poll_status()
>   - Add completion management in spi_mem_poll_status()
>   - Add offload/non-offload case management in spi_mem_poll_status()
>   - Optimize the non-offload case by using read_poll_timeout()
> 
>  drivers/spi/spi-mem.c       | 85 +++++++++++++++++++++++++++++++++++++
>  include/linux/spi/spi-mem.h | 14 ++++++
>  2 files changed, 99 insertions(+)
> 
> diff --git a/drivers/spi/spi-mem.c b/drivers/spi/spi-mem.c
> index 1513553e4080..257dc501d5df 100644
> --- a/drivers/spi/spi-mem.c
> +++ b/drivers/spi/spi-mem.c
> @@ -6,6 +6,7 @@
>   * Author: Boris Brezillon <boris.brezillon@bootlin.com>
>   */
>  #include <linux/dmaengine.h>
> +#include <linux/iopoll.h>
>  #include <linux/pm_runtime.h>
>  #include <linux/spi/spi.h>
>  #include <linux/spi/spi-mem.h>
> @@ -743,6 +744,89 @@ static inline struct spi_mem_driver *to_spi_mem_drv(struct device_driver *drv)
>  	return container_of(drv, struct spi_mem_driver, spidrv.driver);
>  }
>  
> +int spi_mem_read_status(struct spi_mem *mem,
> +			const struct spi_mem_op *op,
> +			u16 *status)
> +{
> +	const u8 *bytes = (u8 *)op->data.buf.in;
> +	int ret;
> +
> +	ret = spi_mem_exec_op(mem, op);
> +	if (ret)
> +		return ret;
> +
> +	if (op->data.nbytes > 1)
> +		*status = ((u16)bytes[0] << 8) | bytes[1];
> +	else
> +		*status = bytes[0];
> +
> +	return 0;
> +}
> +
> +/**
> + * spi_mem_poll_status() - Poll memory device status
> + * @mem: SPI memory device
> + * @op: the memory operation to execute
> + * @mask: status bitmask to ckeck
> + * @match: (status & mask) expected value
> + * @initial_delay_us: delay in us before starting to poll
> + * @polling_delay_us: time to sleep between reads in us
> + * @timeout_ms: timeout in milliseconds
> + *
> + * This function send a polling status request to the controller driver
> + *
> + * Return: 0 in case of success, -ETIMEDOUT in case of error,
> + *         -EOPNOTSUPP if not supported.
> + */
> +int spi_mem_poll_status(struct spi_mem *mem,
> +			const struct spi_mem_op *op,
> +			u16 mask, u16 match,
> +			unsigned long initial_delay_us,
> +			unsigned long polling_delay_us,
> +			u16 timeout_ms)
> +{
> +	struct spi_controller *ctlr = mem->spi->controller;
> +	int ret = -EOPNOTSUPP;
> +	int read_status_ret;
> +	u16 status;
> +
> +	if (op->data.nbytes < 1 || op->data.nbytes > 2)
> +		return -EINVAL;
> +
> +	if (ctlr->mem_ops && ctlr->mem_ops->poll_status) {
> +		ret = spi_mem_access_start(mem);
> +		if (ret)
> +			return ret;
> +
> +		ret = ctlr->mem_ops->poll_status(mem, op, mask, match,
> +						 initial_delay_us, polling_delay_us,
> +						 timeout_ms);
> +
> +		spi_mem_access_end(mem);
> +	}
> +
> +	if (ret == -EOPNOTSUPP) {
> +		if (!spi_mem_supports_op(mem, op))
> +			return ret;
> +
> +		if (initial_delay_us < 10)
> +			udelay(initial_delay_us);
> +		else
> +			usleep_range((initial_delay_us >> 2) + 1,
> +				     initial_delay_us);
> +
> +		ret = read_poll_timeout(spi_mem_read_status, read_status_ret,
> +					(read_status_ret || ((status) & mask) == match),
> +					polling_delay_us, timeout_ms * 1000, false, mem,
> +					op, &status);
> +		if (read_status_ret)
> +			return read_status_ret;
> +	}
> +
> +	return ret;
> +}
> +EXPORT_SYMBOL_GPL(spi_mem_poll_status);
> +
>  static int spi_mem_probe(struct spi_device *spi)
>  {
>  	struct spi_mem_driver *memdrv = to_spi_mem_drv(spi->dev.driver);
> @@ -763,6 +847,7 @@ static int spi_mem_probe(struct spi_device *spi)
>  	if (IS_ERR_OR_NULL(mem->name))
>  		return PTR_ERR_OR_ZERO(mem->name);
>  
> +	init_completion(&ctlr->xfer_completion);

Is this still needed?

>  	spi_set_drvdata(spi, mem);
>  
>  	return memdrv->probe(mem);
> diff --git a/include/linux/spi/spi-mem.h b/include/linux/spi/spi-mem.h
> index 2b65c9edc34e..10375d9ad747 100644
> --- a/include/linux/spi/spi-mem.h
> +++ b/include/linux/spi/spi-mem.h
> @@ -250,6 +250,7 @@ static inline void *spi_mem_get_drvdata(struct spi_mem *mem)
>   *		  the currently mapped area), and the caller of
>   *		  spi_mem_dirmap_write() is responsible for calling it again in
>   *		  this case.
> + * @poll_status: poll memory device status
>   *
>   * This interface should be implemented by SPI controllers providing an
>   * high-level interface to execute SPI memory operation, which is usually the
> @@ -274,6 +275,12 @@ struct spi_controller_mem_ops {
>  			       u64 offs, size_t len, void *buf);
>  	ssize_t (*dirmap_write)(struct spi_mem_dirmap_desc *desc,
>  				u64 offs, size_t len, const void *buf);
> +	int (*poll_status)(struct spi_mem *mem,
> +			   const struct spi_mem_op *op,
> +			   u16 mask, u16 match,
> +			   unsigned long initial_delay_us,
> +			   unsigned long polling_rate_us,
> +			   unsigned long timeout_ms);
>  };
>  
>  /**
> @@ -369,6 +376,13 @@ devm_spi_mem_dirmap_create(struct device *dev, struct spi_mem *mem,
>  void devm_spi_mem_dirmap_destroy(struct device *dev,
>  				 struct spi_mem_dirmap_desc *desc);
>  
> +int spi_mem_poll_status(struct spi_mem *mem,
> +			const struct spi_mem_op *op,
> +			u16 mask, u16 match,
> +			unsigned long initial_delay_us,
> +			unsigned long polling_delay_us,
> +			u16 timeout);
> +
>  int spi_mem_driver_register_with_owner(struct spi_mem_driver *drv,
>  				       struct module *owner);
>  


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

  reply	other threads:[~2021-05-18 11:33 UTC|newest]

Thread overview: 13+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-05-18  9:39 [PATCH v3 0/3] MTD: spinand: Add spi_mem_poll_status() support patrice.chotard
2021-05-18  9:39 ` [PATCH v3 1/3] spi: spi-mem: add automatic poll status functions patrice.chotard
2021-05-18 11:30   ` Boris Brezillon [this message]
2021-05-18 11:50     ` Patrice CHOTARD
2021-05-18 11:40   ` Boris Brezillon
2021-05-18 11:54     ` Patrice CHOTARD
2021-05-18  9:39 ` [PATCH v3 2/3] mtd: spinand: use the spi-mem poll status APIs patrice.chotard
2021-05-18 11:28   ` Boris Brezillon
2021-05-18 11:50     ` Patrice CHOTARD
2021-05-18  9:39 ` [PATCH v3 3/3] spi: stm32-qspi: add automatic poll status feature patrice.chotard
2021-05-18 11:39   ` Boris Brezillon
2021-05-18 11:53     ` Patrice CHOTARD
2021-05-18 11:28 ` [PATCH v3 0/3] MTD: spinand: Add spi_mem_poll_status() support Patrice CHOTARD

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20210518133054.3240b088@collabora.com \
    --to=boris.brezillon@collabora.com \
    --cc=alexandre.torgue@foss.st.com \
    --cc=broonie@kernel.org \
    --cc=christophe.kerello@foss.st.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-mtd@lists.infradead.org \
    --cc=linux-spi@vger.kernel.org \
    --cc=linux-stm32@st-md-mailman.stormreply.com \
    --cc=miquel.raynal@bootlin.com \
    --cc=patrice.chotard@foss.st.com \
    --cc=vigneshr@ti.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).