* boot fail imx6q-apalis-ixora-v1.1 with imx_v6_v7_defconfig @ 2021-05-18 6:25 Nobuhiro Iwamatsu 2021-05-18 20:43 ` Marcel Ziswiler 0 siblings, 1 reply; 3+ messages in thread From: Nobuhiro Iwamatsu @ 2021-05-18 6:25 UTC (permalink / raw) To: shawnguo, marcel.ziswiler; +Cc: linux-arm-kernel Hi, I'm using imx6q-apalis-ixora [0][1] and noticed that the kernel built with imx_v6_v7_defconfig[2] does not boot. Nothing is displayed after "Starting kernel" when booting from the boot loader. Do you know if there is a problem in other boards? I used git bisect to look for problematic commits. The result is as follows. [c8fa942bd3fbd5b05351aff04649064f5d59f0d2] arm64: defconfig: Build in CONFIG_GPIO_MXC by default It boots by removing CONFIG_GPIO_MXC, but this setting seems to be another problem as it is required not only for this hardware, but also for the i.MX series with armv6 and 7. Do you have a information about this issue? Best regards, Nobuhiro [0]: https://www.toradex.com/products/nxp-freescale-imx-6 [1]: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/arch/arm/boot/dts/imx6q-apalis-ixora-v1.1.dts [2]: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/arch/arm/configs/imx_v6_v7_defconfig _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: boot fail imx6q-apalis-ixora-v1.1 with imx_v6_v7_defconfig 2021-05-18 6:25 boot fail imx6q-apalis-ixora-v1.1 with imx_v6_v7_defconfig Nobuhiro Iwamatsu @ 2021-05-18 20:43 ` Marcel Ziswiler 2021-05-20 1:21 ` Nobuhiro Iwamatsu 0 siblings, 1 reply; 3+ messages in thread From: Marcel Ziswiler @ 2021-05-18 20:43 UTC (permalink / raw) To: nobuhiro1.iwamatsu, shawnguo; +Cc: linux-arm-kernel Hi Nobuhiro On Tue, 2021-05-18 at 15:25 +0900, Nobuhiro Iwamatsu wrote: > Hi, > > I'm using imx6q-apalis-ixora [0][1] and noticed that the kernel built with imx_v6_v7_defconfig[2] > does not boot. Nothing is displayed after "Starting kernel" when booting from the boot loader. > Do you know if there is a problem in other boards? I am not aware of any such issue. As a matter of fact, I just tried today's linux-next with your exact configuration and it works for me without any issue (well, at least it boots fine). See console log [3]. > I used git bisect to look for problematic commits. The result is as follows. > > [c8fa942bd3fbd5b05351aff04649064f5d59f0d2] arm64: defconfig: Build in CONFIG_GPIO_MXC by default > > It boots by removing CONFIG_GPIO_MXC, but this setting seems to be another problem as it is required > not only for this hardware, but also for the i.MX series with armv6 and 7. As mentioned above, that does not ring any bell. > Do you have a information about this issue? No, sorry. > Best regards, > Nobuhiro > > [0]: https://www.toradex.com/products/nxp-freescale-imx-6 > [1]: > https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/arch/arm/boot/dts/imx6q-apalis-ixora-v1.1.dts > [2]: > https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/arch/arm/configs/imx_v6_v7_defconfig [3] https://share.toradex.com/9xubz5xmtg5tsyr Cheers Marcel _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: boot fail imx6q-apalis-ixora-v1.1 with imx_v6_v7_defconfig 2021-05-18 20:43 ` Marcel Ziswiler @ 2021-05-20 1:21 ` Nobuhiro Iwamatsu 0 siblings, 0 replies; 3+ messages in thread From: Nobuhiro Iwamatsu @ 2021-05-20 1:21 UTC (permalink / raw) To: Marcel Ziswiler; +Cc: shawnguo, linux-arm-kernel Hi Marcel, Thanks for your check and comment! On Tue, May 18, 2021 at 08:43:53PM +0000, Marcel Ziswiler wrote: > Hi Nobuhiro > > On Tue, 2021-05-18 at 15:25 +0900, Nobuhiro Iwamatsu wrote: > > Hi, > > > > I'm using imx6q-apalis-ixora [0][1] and noticed that the kernel built with imx_v6_v7_defconfig[2] > > does not boot. Nothing is displayed after "Starting kernel" when booting from the boot loader. > > Do you know if there is a problem in other boards? > > I am not aware of any such issue. > > As a matter of fact, I just tried today's linux-next with your exact configuration and it works for me without > any issue (well, at least it boots fine). See console log [3]. > Thank you. > > I used git bisect to look for problematic commits. The result is as follows. > > > > [c8fa942bd3fbd5b05351aff04649064f5d59f0d2] arm64: defconfig: Build in CONFIG_GPIO_MXC by default > > > > It boots by removing CONFIG_GPIO_MXC, but this setting seems to be another problem as it is required > > not only for this hardware, but also for the i.MX series with armv6 and 7. > > As mentioned above, that does not ring any bell. > > > Do you have a information about this issue? > > No, sorry. I compared the logs you provided, there were three differences. U-Boot version, boot method, kernel boot parameters. I'm using an old U-Boot (2016.11-2.0.5+g5c2d46b325) and I'm checking with a TFTP boot. The kernel parameters are as follows. kernel boot parameters: ``` console=ttymxc0,115200n8 root=/dev/nfs rw nfsroot=192.254.0.1:/var/lib/lava/dispatcher/tmp/8747/extract-nfsrootfs-xxvh200s,tcp,hard,vers=3 ip=dhcp ``` u-boot bootlog: ``` Industrial temperature grade DDR3 timings. Trying to boot from MMC1 U-Boot 2016.11-2.0.5+g5c2d46b325 (May 19 2020 - 23:32:51 +0000) CPU: Freescale i.MX6Q rev1.6 at 792 MHz Reset cause: POR I2C: ready DRAM: 2 GiB PMIC: device id: 0x10, revision id: 0x21, programmed MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Using default environment In: serial_mxc Out: serial_mxc Err: serial_mxc Model: Toradex Apalis iMX6 Quad 2GB IT V1.1C, Serial# 10537665 Net: using PHY at 7 FEC [PRIME] ``` I think updating U-boot will fix the problem, but I want to know the cause. If you have any information, could you please let me know? I update U-Boot to check this issue. > > > Best regards, > > Nobuhiro > > > > [0]: https://www.toradex.com/products/nxp-freescale-imx-6 > > [1]: > > https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/arch/arm/boot/dts/imx6q-apalis-ixora-v1.1.dts > > [2]: > > https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/arch/arm/configs/imx_v6_v7_defconfig > > [3] https://share.toradex.com/9xubz5xmtg5tsyr > > Cheers > > Marcel Best regards, Nobuhiro _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2021-05-20 1:23 UTC | newest] Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2021-05-18 6:25 boot fail imx6q-apalis-ixora-v1.1 with imx_v6_v7_defconfig Nobuhiro Iwamatsu 2021-05-18 20:43 ` Marcel Ziswiler 2021-05-20 1:21 ` Nobuhiro Iwamatsu
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).