From: Claudiu Beznea <claudiu.beznea@microchip.com>
To: <nicolas.ferre@microchip.com>, <alexandre.belloni@bootlin.com>,
<ludovic.desroches@microchip.com>, <robh+dt@kernel.org>
Cc: <linux-arm-kernel@lists.infradead.org>,
<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
Eugen Hristev <eugen.hristev@microchip.com>,
Claudiu Beznea <claudiu.beznea@microchip.com>
Subject: [PATCH v4] ARM: dts: at91: sama5d27_wlsom1: add wifi device
Date: Wed, 25 Aug 2021 12:40:55 +0300 [thread overview]
Message-ID: <20210825094055.642941-1-claudiu.beznea@microchip.com> (raw)
From: Eugen Hristev <eugen.hristev@microchip.com>
SAMA5D27 WLSOM1 boards has a WILC3000 device soldered. Add proper
device tree nodes for this.
[eugen.hristev: original author of this code]
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
[nicolas.ferre: original author of this code]
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
[claudiu.beznea: adapt such that make dtbs_check is happy, remove status
for wifi_pwrseq and wifi nodes]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
---
Changes in v4:
- keep only this patch as the rest from series were applied on mmc tree
- remove status="okay" on wifi node and pwrseq node
- adapt to remove all warnings thown by make dtbs_check
arch/arm/boot/dts/at91-sama5d27_wlsom1.dtsi | 70 +++++++++++++++++++++
1 file changed, 70 insertions(+)
diff --git a/arch/arm/boot/dts/at91-sama5d27_wlsom1.dtsi b/arch/arm/boot/dts/at91-sama5d27_wlsom1.dtsi
index 025a78310e3a..21c86171e462 100644
--- a/arch/arm/boot/dts/at91-sama5d27_wlsom1.dtsi
+++ b/arch/arm/boot/dts/at91-sama5d27_wlsom1.dtsi
@@ -30,6 +30,14 @@ main_xtal {
clock-frequency = <24000000>;
};
};
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-wilc1000";
+ reset-gpios = <&pioA PIN_PA27 GPIO_ACTIVE_HIGH>;
+ powerdown-gpios = <&pioA PIN_PA29 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&pinctrl_wilc_pwrseq>;
+ pinctrl-names = "default";
+ };
};
&flx1 {
@@ -310,5 +318,67 @@ pinctrl_qspi1_default: qspi1_default {
<PIN_PB10__QSPI1_IO3>;
bias-pull-up;
};
+
+ pinctrl_sdmmc1_default: sdmmc1_default {
+ cmd-data {
+ pinmux = <PIN_PA28__SDMMC1_CMD>,
+ <PIN_PA18__SDMMC1_DAT0>,
+ <PIN_PA19__SDMMC1_DAT1>,
+ <PIN_PA20__SDMMC1_DAT2>,
+ <PIN_PA21__SDMMC1_DAT3>;
+ bias-disable;
+ };
+
+ conf-ck {
+ pinmux = <PIN_PA22__SDMMC1_CK>;
+ bias-disable;
+ };
+ };
+
+ pinctrl_wilc_default: wilc_default {
+ conf-irq {
+ pinmux = <PIN_PB25__GPIO>;
+ bias-disable;
+ };
+ };
+
+ pinctrl_wilc_pwrseq: wilc_pwrseq {
+ conf-ce-nrst {
+ pinmux = <PIN_PA27__GPIO>,
+ <PIN_PA29__GPIO>;
+ bias-disable;
+ };
+
+ conf-rtcclk {
+ pinmux = <PIN_PB13__PCK1>;
+ bias-disable;
+ };
+ };
+};
+
+&sdmmc1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ bus-width = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdmmc1_default>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ no-1-8-v;
+ non-removable;
+ bus-width = <4>;
+ status = "okay";
+
+ wilc: wifi@0 {
+ reg = <0>;
+ compatible = "microchip,wilc1000";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wilc_default>;
+ clocks = <&pmc PMC_TYPE_SYSTEM 9>;
+ clock-names = "rtc";
+ interrupts = <PIN_PB25 IRQ_TYPE_NONE>;
+ interrupt-parent = <&pioA>;
+ assigned-clocks = <&pmc PMC_TYPE_SYSTEM 9>;
+ assigned-clock-rates = <32768>;
+ };
};
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next reply other threads:[~2021-08-25 9:45 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-08-25 9:40 Claudiu Beznea [this message]
2021-09-15 8:30 ` [PATCH v4] ARM: dts: at91: sama5d27_wlsom1: add wifi device Nicolas Ferre
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210825094055.642941-1-claudiu.beznea@microchip.com \
--to=claudiu.beznea@microchip.com \
--cc=alexandre.belloni@bootlin.com \
--cc=devicetree@vger.kernel.org \
--cc=eugen.hristev@microchip.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=ludovic.desroches@microchip.com \
--cc=nicolas.ferre@microchip.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).