From: Bjorn Helgaas <helgaas@kernel.org>
To: Naveen Naidu <naveennaidu479@gmail.com>
Cc: "Pali Rohár" <pali@kernel.org>, "Rob Herring" <robh@kernel.org>,
"Lorenzo Pieralisi" <lorenzo.pieralisi@arm.com>,
"Krzysztof Wilczyński" <kw@linux.com>,
linux-pci@vger.kernel.org, linux-kernel@vger.kernel.org,
"Thomas Petazzoni" <thomas.petazzoni@bootlin.com>,
bhelgaas@google.com,
linux-kernel-mentees@lists.linuxfoundation.org,
"moderated list:PCI DRIVER FOR AARDVARK (Marvell Armada 3700)"
<linux-arm-kernel@lists.infradead.org>
Subject: Re: [PATCH 09/22] PCI: aardvark: Use SET_PCI_ERROR_RESPONSE() when device not found
Date: Tue, 12 Oct 2021 21:13:10 -0500 [thread overview]
Message-ID: <20211013021310.GA1864069@bhelgaas> (raw)
In-Reply-To: <20211012155928.3nuyzgrgvyjm2v3r@theprophet>
On Tue, Oct 12, 2021 at 09:29:28PM +0530, Naveen Naidu wrote:
> On 11/10, Pali Rohár wrote:
> > On Monday 11 October 2021 23:55:35 Naveen Naidu wrote:
> > > On 11/10, Pali Rohár wrote:
> > > > On Monday 11 October 2021 23:26:33 Naveen Naidu wrote:
> > > > > An MMIO read from a PCI device that doesn't exist or doesn't respond
> > > > > causes a PCI error. There's no real data to return to satisfy the
> > > > > CPU read, so most hardware fabricates ~0 data.
> > > > >
> > > > > Use SET_PCI_ERROR_RESPONSE() to set the error response, when a faulty
> > > > > read occurs.
> > > > >
> > > > > This helps unify PCI error response checking and make error check
> > > > > consistent and easier to find.
> > > > >
> > > > > Compile tested only.
> > > > >
> > > > > Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
> > > > > ---
> > > > > drivers/pci/controller/pci-aardvark.c | 8 ++++----
> > > > > 1 file changed, 4 insertions(+), 4 deletions(-)
> > > > >
> > > > > diff --git a/drivers/pci/controller/pci-aardvark.c b/drivers/pci/controller/pci-aardvark.c
> > > > > index 596ebcfcc82d..dc2f820ef55f 100644
> > > > > --- a/drivers/pci/controller/pci-aardvark.c
> > > > > +++ b/drivers/pci/controller/pci-aardvark.c
> > > > > @@ -894,7 +894,7 @@ static int advk_pcie_rd_conf(struct pci_bus *bus, u32 devfn,
> > > > > int ret;
> > > > >
> > > > > if (!advk_pcie_valid_device(pcie, bus, devfn)) {
> > > > > - *val = 0xffffffff;
> > > > > + SET_PCI_ERROR_RESPONSE(val);
> > > >
> > > > Hello! Now I'm looking at this macro, and should not it depends on
> > > > "size" argument? If doing 8-bit or 16-bit read operation then should not
> > > > it rather sets only low 8 bits or low 16 bits to ones?
> > Function itself is declared as:
> >
> > static int advk_pcie_rd_conf(struct pci_bus *bus, u32 devfn, int where, int size, u32 *val);
> >
> > And in "size" argument is stored number of bytes, kind of read operation
> > (read byte, read word, read dword). In *val is then stored read value.
> > For byte operation, just low 8 bits in *val variable are set.
> >
> > Because *val is u32 it means that typeof(*val) is always 4 independently
> > of the "size" argument.
> >
> > For example other project U-Boot has also pci-aardvark.c driver and
> > U-Boot has for (probably same) purpose pci_get_ff() macro, see:
> > https://source.denx.de/u-boot/u-boot/-/blob/v2021.10/drivers/pci/pci-aardvark.c#L367
> >
> > I'm not saying if current approach to always sets 0xffffffff
> > (independently of "size" argument) is correct or not as I do not know
> > it too! I'm just giving example that this PCI code has very similar
> > implementation of other project (U-Boot) which sets number of ones based
> > on the size argument.
I don't think there's an issue here. advk_pcie_rd_conf() can set the
whole u32 to 0xffffffff regardless of the "size" value because
pci_bus_read_config_byte() and pci_bus_read_config_word() extract out
the part they need:
res = bus->ops->read(bus, devfn, pos, len, &data); \
*value = (type)data; \
where "type" is u8 or u16 (this is hard to grep for; it's in the
PCI_OP_READ() macro in drivers/pci/access.c).
> I am not sure too, if we would like to have something like pci_get_ff()
> which sets the return mask based on the size.
I'd like to see how pci_get_ff() works because this is potentially a
widespread, invasive change and it's always better to copy a good
existing design than to make up something new.
> > Anyway, I very like this your idea to have a macro which purpose is to
> > explicitly indicate error during config read operation! And to unify all
> > drivers to use same style for signalling config read error.
I definitely think there's a lot of value in making this consistent
*somehow*, so thanks for working on this!
Bjorn
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2021-10-13 2:15 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-10-11 17:35 [PATCH 00/22] PCI: Unify PCI error response checking Naveen Naidu
2021-10-11 17:37 ` [PATCH 01/22] PCI: Add PCI_ERROR_RESPONSE and it's related defintions Naveen Naidu
2021-10-11 17:45 ` [PATCH 03/22] PCI: thunder: Use SET_PCI_ERROR_RESPONSE() when device not found Naveen Naidu
2021-10-11 17:46 ` [PATCH 04/22] PCI: iproc: " Naveen Naidu
2021-10-11 17:51 ` [PATCH 05/22] PCI: mediatek: " Naveen Naidu
2021-10-11 17:52 ` [PATCH 06/22] PCI: exynos: " Naveen Naidu
2021-10-11 17:56 ` [PATCH 09/22] PCI: aardvark: " Naveen Naidu
2021-10-11 18:08 ` Pali Rohár
2021-10-11 18:28 ` Naveen Naidu
[not found] ` <20211011182526.kboaxqofdpd2jjrl@theprophet>
2021-10-11 18:41 ` Pali Rohár
2021-10-12 15:59 ` Naveen Naidu
2021-10-13 2:13 ` Bjorn Helgaas [this message]
2021-10-13 17:59 ` Pali Rohár
2021-10-11 18:00 ` [PATCH 10/22] PCI: mvebu: " Naveen Naidu
2021-10-11 18:02 ` [PATCH 13/22] PCI: rockchip: " Naveen Naidu
2021-10-11 18:13 ` [PATCH 22/22] PCI: xgene: Use PCI_ERROR_RESPONSE to specify hardware error Naveen Naidu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20211013021310.GA1864069@bhelgaas \
--to=helgaas@kernel.org \
--cc=bhelgaas@google.com \
--cc=kw@linux.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel-mentees@lists.linuxfoundation.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pci@vger.kernel.org \
--cc=lorenzo.pieralisi@arm.com \
--cc=naveennaidu479@gmail.com \
--cc=pali@kernel.org \
--cc=robh@kernel.org \
--cc=thomas.petazzoni@bootlin.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).