From: Adam Ford <aford173@gmail.com>
To: linux-arm-kernel@lists.infradead.org
Cc: linux-media@vger.kernel.org, laurent.pinchart@ideasonboard.com,
cstevens@beaconembedded.com, aford@beaconembedded.com,
Adam Ford <aford173@gmail.com>, Rob Herring <robh+dt@kernel.org>,
Shawn Guo <shawnguo@kernel.org>,
Sascha Hauer <s.hauer@pengutronix.de>,
Pengutronix Kernel Team <kernel@pengutronix.de>,
Fabio Estevam <festevam@gmail.com>,
NXP Linux Team <linux-imx@nxp.com>,
Catalin Marinas <catalin.marinas@arm.com>,
Will Deacon <will@kernel.org>,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: [RFC V2 5/5] arm64: dts: imx8mm-evk: Enable OV5640 Camera
Date: Sat, 23 Oct 2021 15:34:56 -0500 [thread overview]
Message-ID: <20211023203457.1217821-6-aford173@gmail.com> (raw)
In-Reply-To: <20211023203457.1217821-1-aford173@gmail.com>
The schematic shows support for a camera interface, and the NXP
kernel shows it is an OV5640.
Signed-off-by: Adam Ford <aford173@gmail.com>
---
arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi | 44 +++++++++++++++++++
1 file changed, 44 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
index e033d0257b5a..27217d30b8d8 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
@@ -239,6 +239,10 @@ ldo6_reg: LDO6 {
};
};
+&csi {
+ status = "okay";
+};
+
&i2c2 {
clock-frequency = <400000>;
pinctrl-names = "default";
@@ -287,6 +291,38 @@ pca6416: gpio@20 {
gpio-controller;
#gpio-cells = <2>;
};
+
+ camera@3c {
+ compatible = "ovti,ov5640";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ov5640>;
+ reg = <0x3c>;
+ clocks = <&clk IMX8MM_CLK_CLKO1>;
+ clock-names = "xclk";
+ assigned-clocks = <&clk IMX8MM_CLK_CLKO1>;
+ assigned-clock-parents = <&clk IMX8MM_CLK_24M>;
+ assigned-clock-rates = <24000000>;
+ powerdown-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
+
+ port {
+ /* MIPI CSI-2 bus endpoint */
+ ov5640_to_mipi_csi2: endpoint {
+ remote-endpoint = <&imx8mm_mipi_csi_in>;
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ };
+ };
+ };
+};
+
+&imx8mm_mipi_csi_in {
+ remote-endpoint = <&ov5640_to_mipi_csi2>;
+ data-lanes = <1 2>;
+};
+
+&mipi_csi2 {
+ status = "okay";
};
&sai3 {
@@ -406,6 +442,14 @@ MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3
>;
};
+ pinctrl_ov5640: ov5640grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x19
+ MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x19
+ MX8MM_IOMUXC_GPIO1_IO14_CCMSRCGPCMIX_CLKO1 0x59
+ >;
+ };
+
pinctrl_pmic: pmicirqgrp {
fsl,pins = <
MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x141
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2021-10-23 20:38 UTC|newest]
Thread overview: 22+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-10-23 20:34 [RFC V2 0/5] arm64: dts: imx8mm: Enable CSI and OV5640 Camera Adam Ford
2021-10-23 20:34 ` [RFC V2 1/5] arm64: dts: imx8mm: Add CSI nodes Adam Ford
2021-10-28 2:03 ` Laurent Pinchart
2021-10-23 20:34 ` [RFC V2 2/5] arm64: defconfig: Enable VIDEO_IMX_MEDIA Adam Ford
2021-10-23 20:34 ` [RFC V2 3/5] arm64: dts: imx8mm-beacon: Enable OV5640 Camera Adam Ford
2021-10-23 20:34 ` [RFC V2 4/5] arm64: defconfig: Enable OV5640 Adam Ford
2021-10-23 20:34 ` Adam Ford [this message]
2021-10-28 1:31 ` [RFC V2 5/5] arm64: dts: imx8mm-evk: Enable OV5640 Camera Laurent Pinchart
2021-11-05 16:00 ` Tim Harvey
2021-11-21 23:18 ` Laurent Pinchart
2021-11-02 17:49 ` Tim Harvey
2021-10-24 12:15 ` [RFC V2 0/5] arm64: dts: imx8mm: Enable CSI and " Fabio Estevam
2021-10-28 0:39 ` Adam Ford
2021-10-28 3:35 ` Laurent Pinchart
2021-10-29 11:09 ` Frieder Schrempf
2021-11-01 23:05 ` Tim Harvey
2021-11-02 0:30 ` Adam Ford
2021-11-02 17:50 ` Tim Harvey
2021-11-02 18:08 ` Adam Ford
2021-11-03 0:45 ` Adam Ford
2021-11-05 4:14 ` Adam Ford
2021-11-05 11:13 ` Fabio Estevam
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20211023203457.1217821-6-aford173@gmail.com \
--to=aford173@gmail.com \
--cc=aford@beaconembedded.com \
--cc=catalin.marinas@arm.com \
--cc=cstevens@beaconembedded.com \
--cc=devicetree@vger.kernel.org \
--cc=festevam@gmail.com \
--cc=kernel@pengutronix.de \
--cc=laurent.pinchart@ideasonboard.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-imx@nxp.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-media@vger.kernel.org \
--cc=robh+dt@kernel.org \
--cc=s.hauer@pengutronix.de \
--cc=shawnguo@kernel.org \
--cc=will@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).