[PATCH v2 0/8] arm64: dts: imx8mm-kontron: Improvements and OSM board support

[PATCH v2 0/8] arm64: dts: imx8mm-kontron: Improvements and OSM board support

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

This set contains a few small improvements for the imx8mm-kontron devicetrees
(patch 3-7) and support for a new SoM (patch 8, including baseboard) that
complies to the Open Standard Module (OSM) 1.0 hardware specification, size S
(https://sget.org/standards/osm).

It also includes binding changes for the new board (patch 1) and a binding
change for the PCA9450 PMIC regulators (patch2).

Changes in v2:
* move binding changes to beginning of patchset
* Allow arbitrary regulator names in PCA9450 bindings
* Use voltage rail names from schematic for PMIC regulator-names
* Add SPI NOR partition layout to devicetree
* Remove unneeded header include
* Add tags

Frieder Schrempf (8):
  dt-bindings: arm: fsl: Add Kontron BL i.MX8MM OSM-S board
  dt-bindings: regulator: pca9450: Allow arbitrary regulator names
  arm64: dts: imx8mm-kontron: Adjust board and SoM model strings
  arm64: dts: imx8mm-kontron: Use the VSELECT signal to switch SD card
    IO voltage
  arm64: dts: imx8mm-kontron: Remove low DDRC operating point
  arm64: dts: imx8mm-kontron: Use voltage rail names from schematic for
    PMIC regulator-names
  arm64: dts: imx8mm-kontron: Add SPI NOR partition layout
  arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S

 .../devicetree/bindings/arm/fsl.yaml          |   6 +
 .../regulator/nxp,pca9450-regulator.yaml      |   8 +-
 arch/arm64/boot/dts/freescale/Makefile        |   1 +
 .../dts/freescale/imx8mm-kontron-n801x-s.dts  |   5 +-
 .../freescale/imx8mm-kontron-n801x-som.dtsi   |  51 ++-
 .../dts/freescale/imx8mm-kontron-n802x-s.dts  | 376 ++++++++++++++++++
 .../freescale/imx8mm-kontron-n802x-som.dtsi   | 330 +++++++++++++++
 7 files changed, 754 insertions(+), 23 deletions(-)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-kontron-n802x-s.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-kontron-n802x-som.dtsi

-- 
2.37.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 1/8] dt-bindings: arm: fsl: Add Kontron BL i.MX8MM OSM-S board

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

Add bindings for the Kontron BL i.MX8MM OSM-S board.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
Changes in v2:
* add A-b tag from Krzysztof (Thanks!)
---
 Documentation/devicetree/bindings/arm/fsl.yaml | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index ef524378d449..ef99d948e908 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -847,6 +847,12 @@ properties:
           - const: kontron,imx8mm-n801x-som
           - const: fsl,imx8mm
 
+      - description: Kontron BL i.MX8MM OSM-S (N802X S) Board
+        items:
+          - const: kontron,imx8mm-n802x-s
+          - const: kontron,imx8mm-n802x-som
+          - const: fsl,imx8mm
+
       - description: Toradex Boards with Verdin iMX8M Mini Modules
         items:
           - enum:
-- 
2.37.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 2/8] dt-bindings: regulator: pca9450: Allow arbitrary regulator names

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

Instead of restricting regulator-name to non-descriptive names, allow
to use arbitrary strings. This enables us to use the name of the
voltage rail that is powered by the regulator as some board DTs
already do.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
Changes in v2:
* new patch
---
 .../bindings/regulator/nxp,pca9450-regulator.yaml         | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/Documentation/devicetree/bindings/regulator/nxp,pca9450-regulator.yaml b/Documentation/devicetree/bindings/regulator/nxp,pca9450-regulator.yaml
index b539781e39aa..b1e4fd09928b 100644
--- a/Documentation/devicetree/bindings/regulator/nxp,pca9450-regulator.yaml
+++ b/Documentation/devicetree/bindings/regulator/nxp,pca9450-regulator.yaml
@@ -49,9 +49,9 @@ properties:
 
         properties:
           regulator-name:
-            pattern: "^LDO[1-5]$"
             description:
-              should be "LDO1", ..., "LDO5"
+              Should be "LDO1", ..., "LDO5" or whatever the name of the boards
+              voltage rail powered by this regulator is.
 
         unevaluatedProperties: false
 
@@ -63,9 +63,9 @@ properties:
 
         properties:
           regulator-name:
-            pattern: "^BUCK[1-6]$"
             description:
-              should be "BUCK1", ..., "BUCK6"
+              Should be "BUCK1", ..., "BUCK6" or whatever the name of the boards
+              voltage rail powered by this regulator is.
 
           nxp,dvs-run-voltage:
             $ref: "/schemas/types.yaml#/definitions/uint32"
-- 
2.37.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 3/8] arm64: dts: imx8mm-kontron: Adjust board and SoM model strings

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

The official naming includes "SL" (SoM-Line) or "BL" (Board-Line).
The legacy identifiers are kept in brackets and are still used in
file names and compatible strings.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
Changes in v2:
* none
---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts    | 2 +-
 arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
index 23be1ec538ba..cb8102bb8db5 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
@@ -8,7 +8,7 @@
 #include "imx8mm-kontron-n801x-som.dtsi"
 
 / {
-	model = "Kontron i.MX8MM N801X S";
+	model = "Kontron BL i.MX8MM (N801X)";
 	compatible = "kontron,imx8mm-n801x-s", "kontron,imx8mm-n801x-som", "fsl,imx8mm";
 
 	aliases {
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
index 8f90eb02550d..b6d90d646a5f 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
@@ -6,7 +6,7 @@
 #include "imx8mm.dtsi"
 
 / {
-	model = "Kontron i.MX8MM N801X SoM";
+	model = "Kontron SL i.MX8MM (N801X)";
 	compatible = "kontron,imx8mm-n801x-som", "fsl,imx8mm";
 
 	memory@40000000 {
-- 
2.37.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 4/8] arm64: dts: imx8mm-kontron: Use the VSELECT signal to switch SD card IO voltage

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

It turns out that it is not necessary to declare the VSELECT signal as
GPIO and let the PMIC driver set it to a fixed high level. This switches
the voltage between 3.3V and 1.8V by setting the PMIC register for LDO5
accordingly.

Instead we can do it like other boards already do and simply mux the
VSELECT signal of the USDHC interface to the pin. This makes sure that
the correct voltage is selected by setting the PMIC's SD_VSEL input
to high or low accordingly.

Reported-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Heiko Thiery <heiko.thiery@gmail.com>
---
Changes in v2:
* Add Heiko's R-b tag (Thanks!)
---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts    | 3 +++
 arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi | 2 --
 2 files changed, 3 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
index cb8102bb8db5..bc46426ad8f6 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
@@ -321,6 +321,7 @@ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d0
 			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d0
 			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d0
 			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
 		>;
 	};
 
@@ -333,6 +334,7 @@ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4
 			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4
 			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4
 			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
 		>;
 	};
 
@@ -345,6 +347,7 @@ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d6
 			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d6
 			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d6
 			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
 		>;
 	};
 };
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
index b6d90d646a5f..77c074b491a6 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
@@ -86,7 +86,6 @@ pca9450: pmic@25 {
 		pinctrl-0 = <&pinctrl_pmic>;
 		interrupt-parent = <&gpio1>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
-		sd-vsel-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
 
 		regulators {
 			reg_vdd_soc: BUCK1 {
@@ -229,7 +228,6 @@ MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x400001c3
 	pinctrl_pmic: pmicgrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0		0x141
-			MX8MM_IOMUXC_GPIO1_IO04_GPIO1_IO4		0x141
 		>;
 	};
 
-- 
2.37.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 5/8] arm64: dts: imx8mm-kontron: Remove low DDRC operating point

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

For some reason there is a problem with finding a DDR configuration
that works on all operating points and all LPDDR4 types used on the
SoM. Therefore the bootloader currently doesn't configure the lowest
of the three operating points. Let's also skip this in the kernel
devicetree to make sure it isn't used.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
Changes in v2:
* none
---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi | 4 ----
 1 file changed, 4 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
index 77c074b491a6..2d0661cce89b 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
@@ -46,10 +46,6 @@ &ddrc {
 	ddrc_opp_table: opp-table {
 		compatible = "operating-points-v2";
 
-		opp-25M {
-			opp-hz = /bits/ 64 <25000000>;
-		};
-
 		opp-100M {
 			opp-hz = /bits/ 64 <100000000>;
 		};
-- 
2.37.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 6/8] arm64: dts: imx8mm-kontron: Use voltage rail names from schematic for PMIC regulator-names

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

Improve the naming of the regulators to contain the voltage rail
names from the schematic.

Suggested-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
Changes in v2:
* new patch
---
 .../freescale/imx8mm-kontron-n801x-som.dtsi   | 22 +++++++++----------
 1 file changed, 11 insertions(+), 11 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
index 2d0661cce89b..c995592981c2 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
@@ -85,7 +85,7 @@ pca9450: pmic@25 {
 
 		regulators {
 			reg_vdd_soc: BUCK1 {
-				regulator-name = "buck1";
+				regulator-name = "+0V8_VDD_SOC (BUCK1)";
 				regulator-min-microvolt = <800000>;
 				regulator-max-microvolt = <850000>;
 				regulator-boot-on;
@@ -96,7 +96,7 @@ reg_vdd_soc: BUCK1 {
 			};
 
 			reg_vdd_arm: BUCK2 {
-				regulator-name = "buck2";
+				regulator-name = "+0V9_VDD_ARM (BUCK2)";
 				regulator-min-microvolt = <850000>;
 				regulator-max-microvolt = <950000>;
 				regulator-boot-on;
@@ -107,7 +107,7 @@ reg_vdd_arm: BUCK2 {
 			};
 
 			reg_vdd_dram: BUCK3 {
-				regulator-name = "buck3";
+				regulator-name = "+0V9_VDD_DRAM&PU (BUCK3)";
 				regulator-min-microvolt = <850000>;
 				regulator-max-microvolt = <950000>;
 				regulator-boot-on;
@@ -115,7 +115,7 @@ reg_vdd_dram: BUCK3 {
 			};
 
 			reg_vdd_3v3: BUCK4 {
-				regulator-name = "buck4";
+				regulator-name = "+3V3 (BUCK4)";
 				regulator-min-microvolt = <3300000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-boot-on;
@@ -123,7 +123,7 @@ reg_vdd_3v3: BUCK4 {
 			};
 
 			reg_vdd_1v8: BUCK5 {
-				regulator-name = "buck5";
+				regulator-name = "+1V8 (BUCK5)";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
 				regulator-boot-on;
@@ -131,7 +131,7 @@ reg_vdd_1v8: BUCK5 {
 			};
 
 			reg_nvcc_dram: BUCK6 {
-				regulator-name = "buck6";
+				regulator-name = "+1V1_NVCC_DRAM (BUCK6)";
 				regulator-min-microvolt = <1100000>;
 				regulator-max-microvolt = <1100000>;
 				regulator-boot-on;
@@ -139,7 +139,7 @@ reg_nvcc_dram: BUCK6 {
 			};
 
 			reg_nvcc_snvs: LDO1 {
-				regulator-name = "ldo1";
+				regulator-name = "+1V8_NVCC_SNVS (LDO1)";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
 				regulator-boot-on;
@@ -147,7 +147,7 @@ reg_nvcc_snvs: LDO1 {
 			};
 
 			reg_vdd_snvs: LDO2 {
-				regulator-name = "ldo2";
+				regulator-name = "+0V8_VDD_SNVS (LDO2)";
 				regulator-min-microvolt = <800000>;
 				regulator-max-microvolt = <900000>;
 				regulator-boot-on;
@@ -155,7 +155,7 @@ reg_vdd_snvs: LDO2 {
 			};
 
 			reg_vdda: LDO3 {
-				regulator-name = "ldo3";
+				regulator-name = "+1V8_VDDA (LDO3)";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
 				regulator-boot-on;
@@ -163,7 +163,7 @@ reg_vdda: LDO3 {
 			};
 
 			reg_vdd_phy: LDO4 {
-				regulator-name = "ldo4";
+				regulator-name = "+0V9_VDD_PHY (LDO4)";
 				regulator-min-microvolt = <900000>;
 				regulator-max-microvolt = <900000>;
 				regulator-boot-on;
@@ -171,7 +171,7 @@ reg_vdd_phy: LDO4 {
 			};
 
 			reg_nvcc_sd: LDO5 {
-				regulator-name = "ldo5";
+				regulator-name = "NVCC_SD (LDO5)";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <3300000>;
 			};
-- 
2.37.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 7/8] arm64: dts: imx8mm-kontron: Add SPI NOR partition layout

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

This is the layout used by the bootloader. Add it to the kernel
devicetree to make the same layout available in Linux and have
the devicetrees synced.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
Changes in v2:
* new patch
---
 .../freescale/imx8mm-kontron-n801x-som.dtsi   | 21 +++++++++++++++++++
 1 file changed, 21 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
index c995592981c2..bb87e8b166bf 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
@@ -66,6 +66,27 @@ flash@0 {
 		compatible = "mxicy,mx25r1635f", "jedec,spi-nor";
 		spi-max-frequency = <80000000>;
 		reg = <0>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "u-boot";
+				reg = <0x0 0x1E0000>;
+			};
+
+			partition@1 {
+				label = "env";
+				reg = <0x1E0000 0x10000>;
+			};
+
+			partition@2 {
+				label = "env_redundant";
+				reg = <0x1F0000 0x10000>;
+			};
+		};
 	};
 };
 
-- 
2.37.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 8/8] arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

This adds support for the Kontron Electronics SL i.MX8MM OSM-S SoM
and the matching baseboard BL i.MX8MM OSM-S.

The SoM hardware complies to the Open Standard Module (OSM) 1.0
specification, size S (https://sget.org/standards/osm).

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
Changes in v2:
* add SPI NOR partitions
* use voltage rail names for PMIC regulator-name
* drop unused header include
---
 arch/arm64/boot/dts/freescale/Makefile        |   1 +
 .../dts/freescale/imx8mm-kontron-n802x-s.dts  | 376 ++++++++++++++++++
 .../freescale/imx8mm-kontron-n802x-som.dtsi   | 330 +++++++++++++++
 3 files changed, 707 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-kontron-n802x-s.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-kontron-n802x-som.dtsi

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 238a83e5b8c6..87d1c66c6060 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -56,6 +56,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-ctouch2.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-edimm2.2.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-n801x-s.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-n802x-s.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-mx8menlo.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-nitrogen-r2.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-tqma8mqml-mba8mx.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n802x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n802x-s.dts
new file mode 100644
index 000000000000..3d66506f7484
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n802x-s.dts
@@ -0,0 +1,376 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Copyright (C) 2022 Kontron Electronics GmbH
+ */
+
+/dts-v1/;
+
+#include "imx8mm-kontron-n802x-som.dtsi"
+
+/ {
+	model = "Kontron BL i.MX8MM OSM-S (N802X)";
+	compatible = "kontron,imx8mm-n802x-s", "kontron,imx8mm-n802x-som", "fsl,imx8mm";
+
+	aliases {
+		ethernet1 = &usbnet;
+	};
+
+	/* fixed crystal dedicated to mcp2542fd */
+	osc_can: clock-osc-can {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <40000000>;
+		clock-output-names = "osc-can";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_led>;
+
+		led1 {
+			label = "led1";
+			gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led2 {
+			label = "led2";
+			gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
+		};
+
+		led3 {
+			label = "led3";
+			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	pwm-beeper {
+		compatible = "pwm-beeper";
+		pwms = <&pwm2 0 5000 0>;
+	};
+
+	reg_rst_eth2: regulator-rst-eth2 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usb_eth2>;
+		gpio = <&gpio3 2 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+		regulator-name = "rst-usb-eth2";
+	};
+
+	reg_usb1_vbus: regulator-usb1-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usb1_vbus>;
+		gpio = <&gpio3 25 GPIO_ACTIVE_LOW>;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-name = "usb1-vbus";
+	};
+
+	reg_vdd_5v: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-name = "vdd-5v";
+	};
+};
+
+&ecspi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	can@0 {
+		compatible = "microchip,mcp251xfd";
+		reg = <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_can>;
+		clocks = <&osc_can>;
+		interrupts-extended = <&gpio4 28 IRQ_TYPE_LEVEL_LOW>;
+		/*
+		 * Limit the SPI clock to 15 MHz to prevent issues
+		 * with corrupted data due to chip errata.
+		 */
+		spi-max-frequency = <15000000>;
+		vdd-supply = <&reg_vdd_3v3>;
+		xceiver-supply = <&reg_vdd_5v>;
+	};
+};
+
+&ecspi3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi3>;
+	cs-gpios = <&gpio5 25 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	eeram@0 {
+		compatible = "microchip,48l640";
+		reg = <0>;
+		spi-max-frequency = <20000000>;
+	};
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-connection-type = "rgmii-rxid";
+	phy-handle = <&ethphy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy: ethernet-phy@0 {
+			reg = <0>;
+			reset-assert-us = <1>;
+			reset-deassert-us = <15000>;
+			reset-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&gpio1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio1>;
+	gpio-line-names = "", "", "", "dio1-out", "", "", "dio1-in", "dio2-out",
+			  "dio2-in", "dio3-out", "dio3-in", "dio4-out", "", "", "", "",
+			  "", "", "", "", "", "", "", "",
+			  "", "", "", "", "", "", "", "";
+};
+
+&gpio5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio5>;
+	gpio-line-names = "", "", "dio4-in", "", "", "", "", "",
+			  "", "", "", "", "", "", "", "",
+			  "", "", "", "", "", "", "", "",
+			  "", "", "", "", "", "", "", "";
+};
+
+&i2c4 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	status = "okay";
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	linux,rs485-enabled-at-boot-time;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usbotg1 {
+	dr_mode = "otg";
+	disable-over-current;
+	vbus-supply = <&reg_usb1_vbus>;
+	status = "okay";
+};
+
+&usbotg2 {
+	dr_mode = "host";
+	disable-over-current;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	usb1@1 {
+		compatible = "usb424,9514";
+		reg = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		usbnet: ethernet@1 {
+			compatible = "usb424,ec00";
+			reg = <1>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+		};
+	};
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+	vmmc-supply = <&reg_vdd_3v3>;
+	vqmmc-supply = <&reg_nvcc_sd>;
+	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_can: cangrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28		0x19
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO		0x82
+			MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI		0x82
+			MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK		0x82
+			MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13		0x19
+		>;
+	};
+
+	pinctrl_ecspi3: ecspi3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART2_RXD_ECSPI3_MISO		0x82
+			MX8MM_IOMUXC_UART1_TXD_ECSPI3_MOSI		0x82
+			MX8MM_IOMUXC_UART1_RXD_ECSPI3_SCLK		0x82
+			MX8MM_IOMUXC_UART2_TXD_GPIO5_IO25		0x19
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ENET_MDC_ENET1_MDC			0x3
+			MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO		0x3
+			MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3		0x1f
+			MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2		0x1f
+			MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1		0x1f
+			MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0		0x1f
+			MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3		0x91
+			MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2		0x91
+			MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1		0x91
+			MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0		0x91
+			MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC		0x1f
+			MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC		0x91
+			MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91
+			MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x1f
+			MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1		0x19 /* PHY RST */
+			MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5		0x19 /* ETH IRQ */
+		>;
+	};
+
+	pinctrl_gpio_led: gpioledgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12		0x19
+			MX8MM_IOMUXC_GPIO1_IO13_GPIO1_IO13		0x19
+			MX8MM_IOMUXC_GPIO1_IO14_GPIO1_IO14		0x19
+		>;
+	};
+
+	pinctrl_gpio1: gpio1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3		0x19
+			MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7		0x19
+			MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9		0x19
+			MX8MM_IOMUXC_GPIO1_IO11_GPIO1_IO11		0x19
+			MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6		0x19
+			MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8		0x19
+			MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10		0x19
+		>;
+	};
+
+	pinctrl_gpio5: gpio5grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2		0x19
+		>;
+	};
+
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL			0x400001c3
+			MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA			0x400001c3
+		>;
+	};
+
+	pinctrl_pwm2: pwm2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SPDIF_RX_PWM2_OUT			0x19
+		>;
+	};
+
+	pinctrl_reg_usb1_vbus: regusb1vbusgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI5_MCLK_GPIO3_IO25		0x19
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX		0x140
+			MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX		0x140
+			MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B		0x140
+			MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B		0x140
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX		0x140
+			MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX		0x140
+			MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B		0x140
+			MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B		0x140
+		>;
+	};
+
+	pinctrl_usb_eth2: usbeth2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_CE1_B_GPIO3_IO2		0x19
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x190
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d0
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d0
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d0
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d0
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d0
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x194
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d4
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d4
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x196
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d6
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d6
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d6
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d6
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d6
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n802x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n802x-som.dtsi
new file mode 100644
index 000000000000..812dabecec86
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n802x-som.dtsi
@@ -0,0 +1,330 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Copyright (C) 2022 Kontron Electronics GmbH
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "imx8mm.dtsi"
+
+/ {
+	model = "Kontron SL i.MX8MM OSM-S (N802X)";
+	compatible = "kontron,imx8mm-n802x-som", "fsl,imx8mm";
+
+	memory@40000000 {
+		device_type = "memory";
+		/*
+		 * There are multiple SoM flavors with different DDR sizes.
+		 * The smallest is 1GB. For larger sizes the bootloader will
+		 * update the reg property.
+		 */
+		reg = <0x0 0x40000000 0 0x80000000>;
+	};
+
+	chosen {
+		stdout-path = &uart3;
+	};
+};
+
+&A53_0 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_1 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_2 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_3 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&ddrc {
+	operating-points-v2 = <&ddrc_opp_table>;
+
+	ddrc_opp_table: opp-table {
+		compatible = "operating-points-v2";
+
+		opp-100M {
+			opp-hz = /bits/ 64 <100000000>;
+		};
+
+		opp-750M {
+			opp-hz = /bits/ 64 <750000000>;
+		};
+	};
+};
+
+&ecspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "mxicy,mx25r1635f", "jedec,spi-nor";
+		spi-max-frequency = <80000000>;
+		reg = <0>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "u-boot";
+				reg = <0x0 0x1E0000>;
+			};
+
+			partition@1 {
+				label = "env";
+				reg = <0x1E0000 0x10000>;
+			};
+
+			partition@2 {
+				label = "env_redundant";
+				reg = <0x1F0000 0x10000>;
+			};
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	pca9450: pmic@25 {
+		compatible = "nxp,pca9450a";
+		reg = <0x25>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+		regulators {
+			reg_vdd_soc: BUCK1 {
+				regulator-name = "+0V8_VDD_SOC (BUCK1)";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <3125>;
+				nxp,dvs-run-voltage = <850000>;
+				nxp,dvs-standby-voltage = <800000>;
+			};
+
+			reg_vdd_arm: BUCK2 {
+				regulator-name = "+0V9_VDD_ARM (BUCK2)";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <950000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <3125>;
+				nxp,dvs-run-voltage = <950000>;
+				nxp,dvs-standby-voltage = <850000>;
+			};
+
+			reg_vdd_dram: BUCK3 {
+				regulator-name = "+0V9_VDD_DRAM&PU (BUCK3)";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <950000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_vdd_3v3: BUCK4 {
+				regulator-name = "+3V3 (BUCK4)";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_vdd_1v8: BUCK5 {
+				regulator-name = "+1V8 (BUCK5)";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_nvcc_dram: BUCK6 {
+				regulator-name = "+1V1_NVCC_DRAM (BUCK6)";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_nvcc_snvs: LDO1 {
+				regulator-name = "+1V8_NVCC_SNVS (LDO1)";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_vdd_snvs: LDO2 {
+				regulator-name = "+0V8_VDD_SNVS (LDO2)";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_vdda: LDO3 {
+				regulator-name = "+1V8_VDDA (LDO3)";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_vdd_phy: LDO4 {
+				regulator-name = "+0V9_VDD_PHY (LDO4)";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_nvcc_sd: LDO5 {
+				regulator-name = "NVCC_SD (LDO5)";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+		};
+	};
+
+	rtc@52 {
+		compatible = "microcrystal,rv3028";
+		reg = <0x52>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rtc>;
+		interrupts-extended = <&gpio4 1 IRQ_TYPE_LEVEL_HIGH>;
+		trickle-diode-disable;
+	};
+};
+
+&uart3 { /* console */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	vmmc-supply = <&reg_vdd_3v3>;
+	vqmmc-supply = <&reg_vdd_1v8>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO		0x82
+			MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI		0x82
+			MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK		0x82
+			MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9		0x19
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL			0x400001c3
+			MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x400001c3
+		>;
+	};
+
+	pinctrl_pmic: pmicgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0		0x141
+		>;
+	};
+
+	pinctrl_rtc: rtcgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI1_RXC_GPIO4_IO1			0x19
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX		0x140
+			MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX		0x140
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK			0x190
+			MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD			0x1d0
+			MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0		0x1d0
+			MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1		0x1d0
+			MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2		0x1d0
+			MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3		0x1d0
+			MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4		0x1d0
+			MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5		0x1d0
+			MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6		0x1d0
+			MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7		0x1d0
+			MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B		0x019
+			MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x190
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK			0x194
+			MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD			0x1d4
+			MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0		0x1d4
+			MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1		0x1d4
+			MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2		0x1d4
+			MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3		0x1d4
+			MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4		0x1d4
+			MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5		0x1d4
+			MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6		0x1d4
+			MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7		0x1d4
+			MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B		0x019
+			MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x194
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK			0x196
+			MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD			0x1d6
+			MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0		0x1d6
+			MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1		0x1d6
+			MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2		0x1d6
+			MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3		0x1d6
+			MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4		0x1d6
+			MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5		0x1d6
+			MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6		0x1d6
+			MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7		0x1d6
+			MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B		0x019
+			MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x196
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B		0xc6
+		>;
+	};
+};
-- 
2.37.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 2/8] dt-bindings: regulator: pca9450: Allow arbitrary regulator names

[Mark Brown]

[-- Attachment #1.1: Type: text/plain, Size: 488 bytes --]

On Mon, Aug 01, 2022 at 03:15:46PM +0200, Frieder Schrempf wrote:

>            regulator-name:
> -            pattern: "^LDO[1-5]$"
>              description:
> -              should be "LDO1", ..., "LDO5"
> +              Should be "LDO1", ..., "LDO5" or whatever the name of the boards
> +              voltage rail powered by this regulator is.

This should simply be removed from the bindings for the device, devices
have no business placing any constraint on this generic binding.

[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]

[-- Attachment #2: Type: text/plain, Size: 176 bytes --]

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 2/8] dt-bindings: regulator: pca9450: Allow arbitrary regulator names

[Frieder Schrempf]

Am 01.08.22 um 15:21 schrieb Mark Brown:
> On Mon, Aug 01, 2022 at 03:15:46PM +0200, Frieder Schrempf wrote:
> 
>>            regulator-name:
>> -            pattern: "^LDO[1-5]$"
>>              description:
>> -              should be "LDO1", ..., "LDO5"
>> +              Should be "LDO1", ..., "LDO5" or whatever the name of the boards
>> +              voltage rail powered by this regulator is.
> 
> This should simply be removed from the bindings for the device, devices
> have no business placing any constraint on this generic binding.

Ok, IIUC something like below should do then. I can change this in the
next iteration of this series or send it separately if the rest of the
set gets accepted as-is.

--- a/Documentation/devicetree/bindings/regulator/nxp,pca9450-regulator.yaml
+++ b/Documentation/devicetree/bindings/regulator/nxp,pca9450-regulator.yaml
@@ -47,12 +47,6 @@ properties:
         description:
           Properties for single LDO regulator.

-        properties:
-          regulator-name:
-            pattern: "^LDO[1-5]$"
-            description:
-              should be "LDO1", ..., "LDO5"
-
         unevaluatedProperties: false

       "^BUCK[1-6]$":
@@ -62,11 +56,6 @@ properties:
           Properties for single BUCK regulator.

         properties:
-          regulator-name:
-            pattern: "^BUCK[1-6]$"
-            description:
-              should be "BUCK1", ..., "BUCK6"
-
           nxp,dvs-run-voltage:
             $ref: "/schemas/types.yaml#/definitions/uint32"
             minimum: 600000

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 2/8] dt-bindings: regulator: pca9450: Allow arbitrary regulator names

[Mark Brown]

[-- Attachment #1.1: Type: text/plain, Size: 486 bytes --]

On Mon, Aug 01, 2022 at 03:45:52PM +0200, Frieder Schrempf wrote:
> Am 01.08.22 um 15:21 schrieb Mark Brown:

> > This should simply be removed from the bindings for the device, devices
> > have no business placing any constraint on this generic binding.

> Ok, IIUC something like below should do then. I can change this in the
> next iteration of this series or send it separately if the rest of the
> set gets accepted as-is.

Yes, just send it any time and I can apply it as a fix.

[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]

[-- Attachment #2: Type: text/plain, Size: 176 bytes --]

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel