[PATCH 6/7] arm64: dts: allwinner: h616: OrangePi Zero 2: Add USB nodes

From: Andre Przywara <andre.przywara@arm.com>
To: Jernej Skrabec <jernej.skrabec@gmail.com>,
	Samuel Holland <samuel@sholland.org>,
	Chen-Yu Tsai <wens@csie.org>,
	Kishon Vijay Abraham I <kishon@ti.com>,
	Vinod Koul <vkoul@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
	Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
	linux-phy@lists.infradead.org, linux-usb@vger.kernel.org,
	devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
	linux-sunxi@lists.linux.dev, Karl Kurbjun <karl.os@veroson.com>,
	Icenowy Zheng <icenowy@aosc.io>
Subject: [PATCH 6/7] arm64: dts: allwinner: h616: OrangePi Zero 2: Add USB nodes
Date: Mon, 12 Sep 2022 00:59:44 +0100	[thread overview]
Message-ID: <20220911235945.6635-7-andre.przywara@arm.com> (raw)
In-Reply-To: <20220911235945.6635-1-andre.przywara@arm.com>

The OrangePi Zero 2 has one USB-A host port, VBUS is provided by
a GPIO controlled regulator.
The USB-C port is meant to power the board, but is also connected to
the USB 0 port, which we configure as an MUSB peripheral.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
 .../allwinner/sun50i-h616-orangepi-zero2.dts  | 42 +++++++++++++++++++
 1 file changed, 42 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
index 02893f3ac99d..3197dc43397b 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
@@ -49,8 +49,25 @@ reg_vcc5v: vcc5v {
 		regulator-max-microvolt = <5000000>;
 		regulator-always-on;
 	};
+
+	reg_usb1_vbus: usb1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb1-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&reg_vcc5v>;
+		enable-active-high;
+		gpio = <&pio 2 16 GPIO_ACTIVE_HIGH>; /* PC16 */
+		status = "okay";
+	};
 };
 
+&ehci1 {
+	status = "okay";
+};
+
+/* USB 2 & 3 are on headers only. */
+
 &emac0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&ext_rgmii_pins>;
@@ -76,6 +93,10 @@ &mmc0 {
 	status = "okay";
 };
 
+&ohci1 {
+	status = "okay";
+};
+
 &r_rsb {
 	status = "okay";
 
@@ -211,3 +232,24 @@ &uart0 {
 	pinctrl-0 = <&uart0_ph_pins>;
 	status = "okay";
 };
+
+&usbotg {
+	/*
+	 * PHY0 pins are connected to a USB-C socket, but a role switch
+	 * is not implemented: both CC pins are pulled to GND.
+	 * The VBUS pins power the device, so a fixed peripheral mode
+	 * is the best choice.
+	 * The board can be powered via GPIOs, in this case port0 *can*
+	 * act as a host (with a cable/adapter ignoring CC), as VBUS is
+	 * then provided by the GPIOs. Any user of this setup would
+	 * need to adjust the DT accordingly: dr_mode set to "host",
+	 * enabling OHCI0 and EHCI0.
+	 */
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbphy {
+	usb1_vbus-supply = <&reg_usb1_vbus>;
+	status = "okay";
+};
-- 
2.35.3


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
