From: Han Xu <han.xu@nxp.com>
To: Abel Vesa <abelvesa@kernel.org>,
Michael Turquette <mturquette@baylibre.com>,
Stephen Boyd <sboyd@kernel.org>, Shawn Guo <shawnguo@kernel.org>,
Sascha Hauer <s.hauer@pengutronix.de>,
Pengutronix Kernel Team <kernel@pengutronix.de>,
Fabio Estevam <festevam@gmail.com>,
NXP Linux Team <linux-imx@nxp.com>,
linux-clk@vger.kernel.org (open list:NXP i.MX CLOCK DRIVERS),
linux-arm-kernel@lists.infradead.org (moderated
list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE),
linux-kernel@vger.kernel.org (open list)
Cc: miquel.raynal@bootlin.com, linux-mtd@lists.infradead.org, han.xu@nxp.com
Subject: [PATCH] clk: imx: imx6sx: remove the SET_RATE_PARENT flag for QSPI clocks
Date: Wed, 14 Sep 2022 15:10:49 -0500 [thread overview]
Message-ID: <20220914201049.3508104-2-han.xu@nxp.com> (raw)
In-Reply-To: <20220914201049.3508104-1-han.xu@nxp.com>
There is no dedicate parent clock for QSPI so SET_RATE_PARENT flag
should not be used. For instance, the default parent clock for QSPI is
pll2_bus, which is also the parent clock for quite a few modules, such
as MMDC, once GPMI NAND set clock rate for EDO5 mode can cause system
hang due to pll2_bus rate changed.
Fixes: f1541e15e38e ("clk: imx6sx: Switch to clk_hw based API")
Signed-off-by: Han Xu <han.xu@nxp.com>
---
drivers/clk/imx/clk-imx6sx.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/clk/imx/clk-imx6sx.c b/drivers/clk/imx/clk-imx6sx.c
index 2301d8fb8c76..1e53e366cde7 100644
--- a/drivers/clk/imx/clk-imx6sx.c
+++ b/drivers/clk/imx/clk-imx6sx.c
@@ -324,13 +324,13 @@ static void __init imx6sx_clocks_init(struct device_node *ccm_node)
hws[IMX6SX_CLK_SSI3_SEL] = imx_clk_hw_mux("ssi3_sel", base + 0x1c, 14, 2, ssi_sels, ARRAY_SIZE(ssi_sels));
hws[IMX6SX_CLK_SSI2_SEL] = imx_clk_hw_mux("ssi2_sel", base + 0x1c, 12, 2, ssi_sels, ARRAY_SIZE(ssi_sels));
hws[IMX6SX_CLK_SSI1_SEL] = imx_clk_hw_mux("ssi1_sel", base + 0x1c, 10, 2, ssi_sels, ARRAY_SIZE(ssi_sels));
- hws[IMX6SX_CLK_QSPI1_SEL] = imx_clk_hw_mux_flags("qspi1_sel", base + 0x1c, 7, 3, qspi1_sels, ARRAY_SIZE(qspi1_sels), CLK_SET_RATE_PARENT);
+ hws[IMX6SX_CLK_QSPI1_SEL] = imx_clk_hw_mux("qspi1_sel", base + 0x1c, 7, 3, qspi1_sels, ARRAY_SIZE(qspi1_sels);
hws[IMX6SX_CLK_PERCLK_SEL] = imx_clk_hw_mux("perclk_sel", base + 0x1c, 6, 1, perclk_sels, ARRAY_SIZE(perclk_sels));
hws[IMX6SX_CLK_VID_SEL] = imx_clk_hw_mux("vid_sel", base + 0x20, 21, 3, vid_sels, ARRAY_SIZE(vid_sels));
hws[IMX6SX_CLK_ESAI_SEL] = imx_clk_hw_mux("esai_sel", base + 0x20, 19, 2, audio_sels, ARRAY_SIZE(audio_sels));
hws[IMX6SX_CLK_CAN_SEL] = imx_clk_hw_mux("can_sel", base + 0x20, 8, 2, can_sels, ARRAY_SIZE(can_sels));
hws[IMX6SX_CLK_UART_SEL] = imx_clk_hw_mux("uart_sel", base + 0x24, 6, 1, uart_sels, ARRAY_SIZE(uart_sels));
- hws[IMX6SX_CLK_QSPI2_SEL] = imx_clk_hw_mux_flags("qspi2_sel", base + 0x2c, 15, 3, qspi2_sels, ARRAY_SIZE(qspi2_sels), CLK_SET_RATE_PARENT);
+ hws[IMX6SX_CLK_QSPI2_SEL] = imx_clk_hw_mux("qspi2_sel", base + 0x2c, 15, 3, qspi2_sels, ARRAY_SIZE(qspi2_sels);
hws[IMX6SX_CLK_SPDIF_SEL] = imx_clk_hw_mux("spdif_sel", base + 0x30, 20, 2, audio_sels, ARRAY_SIZE(audio_sels));
hws[IMX6SX_CLK_AUDIO_SEL] = imx_clk_hw_mux("audio_sel", base + 0x30, 7, 2, audio_sels, ARRAY_SIZE(audio_sels));
hws[IMX6SX_CLK_ENET_PRE_SEL] = imx_clk_hw_mux("enet_pre_sel", base + 0x34, 15, 3, enet_pre_sels, ARRAY_SIZE(enet_pre_sels));
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2022-09-14 20:12 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-09-14 20:10 [PATCH] clk: imx: imx6sx: remove the SET_RATE_PARENT flag for QSPI clocks Han Xu
2022-09-14 20:10 ` Han Xu [this message]
2022-09-15 7:42 ` kernel test robot
2022-09-15 14:02 ` kernel test robot
2022-09-14 20:51 ` Fabio Estevam
2022-09-15 14:10 ` Fabio Estevam
2022-09-14 22:11 ` Abel Vesa
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20220914201049.3508104-2-han.xu@nxp.com \
--to=han.xu@nxp.com \
--cc=abelvesa@kernel.org \
--cc=festevam@gmail.com \
--cc=kernel@pengutronix.de \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-imx@nxp.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mtd@lists.infradead.org \
--cc=miquel.raynal@bootlin.com \
--cc=mturquette@baylibre.com \
--cc=s.hauer@pengutronix.de \
--cc=sboyd@kernel.org \
--cc=shawnguo@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).