[PATCH v2 3/3] arm64: dts: rockchip: Add Beelink A1

[Robin Murphy <robin.murphy@arm.com>]

Beelink A1 is a TV box implementing the higher-end options of the
RK3328 reference design - the DTB from the stock Android firmware is
clearly the "rk3328-box-plus" variant from the Rockchip 3.10 BSP with
minor modifications to accommodate the USB WiFi module and additional
VFD-style LED driver. It features:

- 4GB of 32-bit LPDDR3
- 16GB of HS200 eMMC (newer models with 32GB also exist)
- Realtek RTL8211F phy for gigabit ethernet
- Fn-Link 6221E-UUC module (RealTek RTL8821CU) for 11ac WiFi and Bluetooth 4.2
- HDMI and analog A/V
- 1x USB 3.0 type A host, 1x USB 2.0 type A OTG, 1x micro SD
- IR receiver and a neat little LED clock display.

Signed-off-by: Robin Murphy <robin.murphy@arm.com>
---
 arch/arm64/boot/dts/rockchip/Makefile      |   1 +
 arch/arm64/boot/dts/rockchip/rk3328-a1.dts | 359 +++++++++++++++++++++
 2 files changed, 360 insertions(+)
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3328-a1.dts

diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 1f18a9392d15..a6f250e7cde2 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -1,5 +1,6 @@
 # SPDX-License-Identifier: GPL-2.0
 dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-evb.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-a1.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-evb.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock64.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-roc-cc.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3328-a1.dts b/arch/arm64/boot/dts/rockchip/rk3328-a1.dts
new file mode 100644
index 000000000000..76b49f573101
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3328-a1.dts
@@ -0,0 +1,359 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+// Copyright (c) 2017-2019 Arm Ltd.
+
+/dts-v1/;
+#include "rk3328.dtsi"
+
+/ {
+	model = "Beelink A1";
+	compatible = "azw,beelink-a1", "rockchip,rk3328";
+
+	/*
+	 * UART pins, as viewed with bottom of case removed:
+	 *
+	 *           Front
+	 *        /-------
+	 *  L    / o <- Gnd
+	 *  e   / o <-- Rx
+	 *  f  / o <--- Tx
+	 *  t / o <---- +3.3v
+	 *    |
+	 */
+	chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
+	gmac_clkin: external-gmac-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "gmac_clkin";
+		#clock-cells = <0>;
+	};
+
+	vcc_host_5v: usb3-current-switch {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 RK_PA0 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb30_host_drv>;
+		regulator-name = "vcc_host_5v";
+		vin-supply = <&vcc_sys>;
+	};
+
+	vcc_sys: vcc-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_sys";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	ir-receiver {
+		compatible = "gpio-ir-receiver";
+		gpios = <&gpio2 RK_PA2 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&analog_sound {
+	simple-audio-card,name = "Analog A/V";
+	status = "okay";
+};
+
+&codec {
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&vdd_arm>;
+};
+
+&cpu1 {
+	cpu-supply = <&vdd_arm>;
+};
+
+&cpu2 {
+	cpu-supply = <&vdd_arm>;
+};
+
+&cpu3 {
+	cpu-supply = <&vdd_arm>;
+};
+
+&emmc {
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	no-sd;
+	no-sdio;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
+	vmmc-supply = <&vcc_io>;
+	vqmmc-supply = <&vcc18_emmc>;
+	status = "okay";
+};
+
+&gmac2io {
+	assigned-clocks = <&cru SCLK_MAC2IO>, <&cru SCLK_MAC2IO_EXT>;
+	assigned-clock-parents = <&gmac_clkin>, <&gmac_clkin>;
+	clock_in_out = "input";
+	phy-handle = <&rtl8211f>;
+	phy-mode = "rgmii";
+	phy-supply = <&vcc_io>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmiim1_pins>;
+	snps,aal;
+	snps,pbl = <0x4>;
+	tx_delay = <0x26>;
+	rx_delay = <0x11>;
+	status = "okay";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rtl8211f: phy@0 {
+			reg = <0>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <30000>;
+			reset-gpios = <&gpio2 RK_PC1 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&gpu {
+	mali-supply = <&vdd_logic>;
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmiphy {
+	status = "okay";
+};
+
+&hdmi_sound {
+	status = "okay";
+};
+
+&i2c1 {
+	clock-frequency = <1000000>;
+	i2c-scl-falling-time-ns = <5>;
+	i2c-scl-rising-time-ns = <83>;
+	status = "okay";
+
+	pmic@18 {
+		compatible = "rockchip,rk805";
+		reg = <0x18>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <RK_PA6 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int_l>;
+		rockchip,system-power-controller;
+		wakeup-source;
+
+		vcc1-supply = <&vcc_sys>;
+		vcc2-supply = <&vcc_sys>;
+		vcc3-supply = <&vcc_sys>;
+		vcc4-supply = <&vcc_sys>;
+		vcc5-supply = <&vcc_io>;
+		vcc6-supply = <&vcc_io>;
+
+		regulators {
+			vdd_logic: DCDC_REG1 {
+				regulator-name = "vdd_logic";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			vdd_arm: DCDC_REG2 {
+				regulator-name = "vdd_arm";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <950000>;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-name = "vcc_ddr";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_io: DCDC_REG4 {
+				regulator-name = "vcc_io";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vdd_18: LDO_REG1 {
+				regulator-name = "vdd_18";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcc18_emmc: LDO_REG2 {
+				regulator-name = "vcc_18emmc";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vdd_11: LDO_REG3 {
+				regulator-name = "vdd_11";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1100000>;
+				};
+			};
+		};
+	};
+};
+
+&i2s0 {
+	status = "okay";
+};
+
+&i2s1 {
+	status = "okay";
+};
+
+&io_domains {
+	vccio1-supply = <&vcc_io>;
+	vccio2-supply = <&vcc18_emmc>;
+	vccio3-supply = <&vcc_io>;
+	vccio4-supply = <&vdd_18>;
+	vccio5-supply = <&vcc_io>;
+	vccio6-supply = <&vdd_18>;
+	pmuio-supply = <&vcc_io>;
+	status = "okay";
+};
+
+&pinctrl {
+	pmic {
+		pmic_int_l: pmic-int-l {
+			rockchip,pins = <2 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	usb3 {
+		usb30_host_drv: usb30-host-drv {
+			rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	wifi {
+		bt_dis: bt-dis {
+			rockchip,pins = <2 RK_PC5 RK_FUNC_GPIO &pcfg_output_low>;
+		};
+
+		bt_wake_host: bt-wake-host {
+			rockchip,pins = <2 RK_PC0 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		chip_en: chip-en {
+			rockchip,pins = <2 RK_PC3 RK_FUNC_GPIO &pcfg_output_low>;
+		};
+
+		host_wake_bt: host-wake-bt {
+			rockchip,pins = <2 RK_PB7 RK_FUNC_GPIO &pcfg_output_high>;
+		};
+
+		wl_dis: wl-dis {
+			rockchip,pins = <3 RK_PB0 RK_FUNC_GPIO &pcfg_output_low>;
+		};
+
+		wl_wake_host: wl-wake-host {
+			rockchip,pins = <3 RK_PA1 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	disable-wp;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc0_clk &sdmmc0_cmd &sdmmc0_dectn &sdmmc0_bus4>;
+	vmmc-supply = <&vcc_io>;
+	vqmmc-supply = <&vcc_io>;
+	status = "okay";
+};
+
+&tsadc {
+	rockchip,hw-tshut-mode = <0>;
+	rockchip,hw-tshut-polarity = <0>;
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&u2phy {
+	status = "okay";
+};
+
+&u2phy_host {
+	status = "okay";
+};
+
+&u2phy_otg {
+	status = "okay";
+};
+
+&usb20_otg {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	pinctrl-names = "default";
+	pinctrl-0 = <&bt_dis &bt_wake_host &chip_en &host_wake_bt &wl_dis &wl_wake_host>;
+	status = "okay";
+};
+
+&vop {
+	status = "okay";
+};
+
+&vop_mmu {
+	status = "okay";
+};
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel