From mboxrd@z Thu Jan 1 00:00:00 1970 From: icenowy@aosc.io (Icenowy Zheng) Date: Fri, 26 Oct 2018 08:08:43 +0800 Subject: [PATCH 4/9] dt-bindings: Add ANX6345 DP/eDP transmitter binding In-Reply-To: <20181025183003.GA12672@bogus> References: <20181018073327.64942-1-icenowy@aosc.io> <1886367.eljNk7jKYl@avalon> <2778638.na8ndVNUfi@avalon> <20181025183003.GA12672@bogus> Message-ID: <3E73AB92-AFD7-4DA6-AF42-725B894DE114@aosc.io> To: linux-arm-kernel@lists.infradead.org List-Id: linux-arm-kernel.lists.infradead.org ? 2018?10?26? GMT+08:00 ??2:30:03, Rob Herring ??: >On Thu, Oct 18, 2018 at 08:40:11PM +0800, Icenowy Zheng wrote: >> ? 2018-10-18?? 14:23 +0300?Laurent Pinchart??? >> > Hi Icenowy, >> > >> > On Thursday, 18 October 2018 13:00:05 EEST Icenowy Zheng wrote: >> > > ? 2018-10-18?? 11:53 +0300?Laurent Pinchart??? >> > > > On Thursday, 18 October 2018 10:33:22 EEST Icenowy Zheng wrote: >> > > > > The ANX6345 is an ultra-low power DisplayPort/eDP transmitter >> > > > > designed >> > > > > for portable devices. >> > > > > >> > > > > Add a binding document for it. >> > > > > >> > > > > Signed-off-by: Icenowy Zheng >> > > > > --- >> > > > > >> > > > > .../bindings/display/bridge/anx6345.txt | 39 >> > > > > +++++++++++++++++++ >> > > > > >> > > > > 1 file changed, 39 insertions(+) >> > > > > create mode 100644 >> > > > > >> > > > > Documentation/devicetree/bindings/display/bridge/anx6345.txt >> > > > > >> > > > > diff --git >> > > > > >a/Documentation/devicetree/bindings/display/bridge/anx6345.txt >> > > > > >b/Documentation/devicetree/bindings/display/bridge/anx6345.txt >> > > > > new >> > > > > file >> > > > > mode 100644 >> > > > > index 000000000000..0689d4eb5f65 >> > > > > --- /dev/null >> > > > > +++ >> > > > > >b/Documentation/devicetree/bindings/display/bridge/anx6345.txt >> > > > > @@ -0,0 +1,39 @@ >> > > > > +Analogix ANX6345 eDP Transmitter >> > > > > +-------------------------------- >> > > > > + >> > > > > +The ANX6345 is an ultra-low power Full-HD eDP transmitter >> > > > > designed >> > > > > for >> > > > > +portable devices. >> > > > > + >> > > > > +Required properties: >> > > > > + >> > > > > + - compatible : "analogix,anx6345" >> > > > > + - reg : I2C address of the device >> > > > > + - reset-gpios : Which GPIO to use for reset >> > > > > + >> > > > > +Optional properties: >> > > > > + >> > > > > + - dvdd12-supply : Regulator for 1.2V digital core >> > > > > power. >> > > > > + - dvdd25-supply : Regulator for 2.5V digital core >> > > > > power. >> > > > >> > > > Shouldn't these to supplies be mandatory ? >> > > >> > > Yes they should. >> > > >> > > > > + - panel-supply : Regulator for the power of >> > > > > the panel. >> > > > >> > > > Shouldn't the panel supply for specified in the DT node of the >> > > > panel >> > > > ? >> > > >> > > However, eDP panel can be probed, may vary on the same device, >and >> > > we >> > > don't have a generic binding for it... >> > >> > Shouldn't we fix that ? :-) >> >> Maybe we should create a connector binding instead of a panel >binding? > >There's not any such thing as a standard eDP connector, is there? >Otherwise, that's just creating a generic panel binding in disguise. >Maybe if eDP interface is standardized enough in terms of power >control, >control lines, EDID at least sometimes present, etc., then we could eDP has the same display signal set with DP, including AUX which carries DPCD and EDID (if present). But I don't know whether other lines are standardized, including power, backlight, etc. >have >some sort of generic eDP panel/connector binding. > >Rob > >_______________________________________________ >linux-arm-kernel mailing list >linux-arm-kernel at lists.infradead.org >http://lists.infradead.org/mailman/listinfo/linux-arm-kernel