From mboxrd@z Thu Jan  1 00:00:00 1970
From: rjui@broadcom.com (Ray Jui)
Date: Sun, 29 Mar 2015 22:09:30 -0700
Subject: [PATCH v6 0/6] Add common clock support for Broadcom iProc
 architecture
In-Reply-To: <1426657522-2473-1-git-send-email-rjui@broadcom.com>
References: <1426657522-2473-1-git-send-email-rjui@broadcom.com>
Message-ID: <5518DA8A.8030905@broadcom.com>
To: linux-arm-kernel@lists.infradead.org
List-Id: linux-arm-kernel.lists.infradead.org

Hi Mike,

This is the latest patch series of the Broadcom iProc clock driver that
I was talking about. I believe it has addressed your previous code
review comments by switching to use assigned-clocks/assigned-clock-rates
for configuring PLL clock at the time of clock registration.

Please have a look and let us know if this can be pulled in.

Thanks,

Ray

On 3/17/2015 10:45 PM, Ray Jui wrote:
> This patchset contains the initial common clock support for Broadcom's iProc
> family of SoCs. The iProc clock architecture comprises of various PLLs, e.g.,
> ARMPLL, GENPLL, LCPLL0, MIPIPLL, and etc. An onboard crystal serves as the
> basic reference clock for these PLLs. Each PLL may have several leaf clocks.
> One special group of clocks is the ASIU clocks, which are dervied directly
> from the crystal reference clock.
> 
> This patchset also contains the basic clock support for the Broadcom Cygnus
> SoC, which implements the iProc clock architecture
> 
> Changes from v5:
>  - Rebase to v4.0-rc4
>  - Drop of_clk_get_parent_rate helper function from the clock framework
>  - Get rid of custom "clock-frequency" support in iProc PLL code. Instead, add
>    standard clock set_rate and round_rate support and make use of DT properties
>    "assigned-clocks" and "assigned-clock-rates" to initialize PLL to the
>    desired rate when registering to the clock framework
>  - Add SW workaround for ASIC bug on MIPI PLL to always read back the same
>    register following a write transaction, to ensure value is written to the
>    correct register
> 
> Changes from v4:
>  - Add of_clk_get_parent_rate helper function into the clock framework
>  - Switch to use of_clk_get_parent_rate in the iProc PLL clock driver
> 
> Changes from v3:
>  - Fix incorrect use of passing in of_clk_src_onecell_get when adding ARM PLL
>    and other iProc PLLs as clock provider. These PLLs have zero cells in DT and
>    thefore of_clk_src_simple_get should be used instead
>  - Rename Cygnus MIPI PLL Channel 2 clock from BCM_CYGNUS_MIPIPLL_CH2_UNUSED
>    to BCM_CYGNUS_MIPIPLL_CH2_V3D, since a 3D graphic rendering engine has been
>    integrated into Cygnus revision B0 and has its core clock running off
>    MIPI PLL Channel 2
>  - Changed default MIPI PLL VCO frequency from 1.75 GHz to 2.1 GHz. This allows
>    us to derive 300 MHz V3D clock from channel 2 through the post divisor
> 
> Changes from v2:
>  - Re-arrange Cygnus clock/pll init functions so each init function is right
>    next to its clock table
>  - Removed #defines for number of clocks in Cygnus. Have the number of clocks
>    automatically determined based on array size of the clock table
> 
> Changes from v1:
>  - Separate drivers/clk/Makefile change for drivers/clk/bcm out to a standalone patch
> 
> Ray Jui (6):
>   clk: iproc: define Broadcom iProc clock binding
>   clk: iproc: add initial common clock support
>   clk: Change bcm clocks build dependency
>   clk: cygnus: add clock support for Broadcom Cygnus
>   ARM: dts: enable clock support for Broadcom Cygnus
>   clk: cygnus: remove Cygnus dummy clock binding
> 
>  .../devicetree/bindings/clock/bcm-cygnus-clock.txt |   34 --
>  .../bindings/clock/brcm,iproc-clocks.txt           |  171 +++++++
>  arch/arm/boot/dts/bcm-cygnus-clock.dtsi            |  112 ++++-
>  arch/arm/boot/dts/bcm-cygnus.dtsi                  |    2 +-
>  drivers/clk/Makefile                               |    2 +-
>  drivers/clk/bcm/Kconfig                            |    9 +
>  drivers/clk/bcm/Makefile                           |    2 +
>  drivers/clk/bcm/clk-cygnus.c                       |  284 ++++++++++++
>  drivers/clk/bcm/clk-iproc-armpll.c                 |  282 +++++++++++
>  drivers/clk/bcm/clk-iproc-asiu.c                   |  275 +++++++++++
>  drivers/clk/bcm/clk-iproc-clk.c                    |  244 ++++++++++
>  drivers/clk/bcm/clk-iproc-pll.c                    |  490 ++++++++++++++++++++
>  drivers/clk/bcm/clk-iproc.h                        |  164 +++++++
>  include/dt-bindings/clock/bcm-cygnus.h             |   65 +++
>  14 files changed, 2075 insertions(+), 61 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/clock/bcm-cygnus-clock.txt
>  create mode 100644 Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt
>  create mode 100644 drivers/clk/bcm/clk-cygnus.c
>  create mode 100644 drivers/clk/bcm/clk-iproc-armpll.c
>  create mode 100644 drivers/clk/bcm/clk-iproc-asiu.c
>  create mode 100644 drivers/clk/bcm/clk-iproc-clk.c
>  create mode 100644 drivers/clk/bcm/clk-iproc-pll.c
>  create mode 100644 drivers/clk/bcm/clk-iproc.h
>  create mode 100644 include/dt-bindings/clock/bcm-cygnus.h
>