Re: [PATCH 2/3] iio: adc: stm32-adc: add analog switches supply control

[Fabrice Gasnier <fabrice.gasnier@st.com>]

On 6/17/19 2:43 PM, Fabrice Gasnier wrote:
> On 6/16/19 5:07 PM, Jonathan Cameron wrote:
>> On Wed, 12 Jun 2019 09:24:35 +0200
>> Fabrice Gasnier <fabrice.gasnier@st.com> wrote:
>>
>>> On stm32h7 and stm32mp1, the ADC inputs are multiplexed with analog
>>> switches which have reduced performances when their supply is below 2.7V
>>> (vdda by default):
>>> - vdd supply can be selected if above 2.7V by setting ANASWVDD syscfg bit
>>>   (STM32MP1 only).
>>> - Voltage booster can be used, to get full ADC performances by setting
>>>   BOOSTE/EN_BOOSTER syscfg bit (increases power consumption).
>>>
>>> Make this optional, since this is a trade-off between analog performance
>>> and power consumption.
>>>
>>> Note: STM32H7 syscfg has a set and clear register for "BOOSTE" control.
>>> STM32MP1 has separate set and clear registers pair to control EN_BOOSTER
>>> and ANASWVDD bits.
>>>
>>> Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
>>
>> A few minor bits inline, but mostly seems fine to me.
>>
>> Jonathan
>>
>>> ---
>>>  drivers/iio/adc/stm32-adc-core.c | 232 ++++++++++++++++++++++++++++++++++++++-
>>>  1 file changed, 230 insertions(+), 2 deletions(-)
>>>
>>> diff --git a/drivers/iio/adc/stm32-adc-core.c b/drivers/iio/adc/stm32-adc-core.c
>>> index 2327ec1..9d41b16 100644
>>> --- a/drivers/iio/adc/stm32-adc-core.c
>>> +++ b/drivers/iio/adc/stm32-adc-core.c
>>> @@ -14,9 +14,11 @@
>>>  #include <linux/irqchip/chained_irq.h>
>>>  #include <linux/irqdesc.h>
>>>  #include <linux/irqdomain.h>
>>> +#include <linux/mfd/syscon.h>
>>>  #include <linux/module.h>
>>>  #include <linux/of_device.h>
>>>  #include <linux/pm_runtime.h>
>>> +#include <linux/regmap.h>
>>>  #include <linux/regulator/consumer.h>
>>>  #include <linux/slab.h>
>>>  
>>> @@ -51,6 +53,20 @@
>>>  
>>>  #define STM32_ADC_CORE_SLEEP_DELAY_MS	2000
>>>  
>>> +/* SYSCFG registers */
>>> +#define STM32H7_SYSCFG_PMCR		0x04
>>> +#define STM32MP1_SYSCFG_PMCSETR		0x04
>>> +#define STM32MP1_SYSCFG_PMCCLRR		0x44
>>> +
>>> +/* SYSCFG bit fields */
>>> +#define STM32H7_SYSCFG_BOOSTE_MASK	BIT(8)
>>> +#define STM32MP1_SYSCFG_ANASWVDD_MASK	BIT(9)
>>> +
>>> +/* SYSCFG capability flags */
>>> +#define HAS_VBOOSTER		BIT(0)
>>> +#define HAS_ANASWVDD		BIT(1)
>>> +#define HAS_CLEAR_REG		BIT(2)
>>> +
>>>  /**
>>>   * stm32_adc_common_regs - stm32 common registers, compatible dependent data
>>>   * @csr:	common status register offset
>>> @@ -58,6 +74,11 @@
>>>   * @eoc1:	adc1 end of conversion flag in @csr
>>>   * @eoc2:	adc2 end of conversion flag in @csr
>>>   * @eoc3:	adc3 end of conversion flag in @csr
>>> + * @has_syscfg: SYSCFG capability flags
>>> + * @pmcr:	SYSCFG_PMCSETR/SYSCFG_PMCR register offset
>>> + * @pmcc:	SYSCFG_PMCCLRR clear register offset
>>> + * @booste_msk:	SYSCFG BOOSTE / EN_BOOSTER bitmask in PMCR & PMCCLRR
>>> + * @anaswvdd_msk: SYSCFG ANASWVDD bitmask in PMCR & PMCCLRR
>>>   */
>>>  struct stm32_adc_common_regs {
>>>  	u32 csr;
>>> @@ -65,6 +86,11 @@ struct stm32_adc_common_regs {
>>>  	u32 eoc1_msk;
>>>  	u32 eoc2_msk;
>>>  	u32 eoc3_msk;
>>> +	unsigned int has_syscfg;
>>> +	u32 pmcr;
>>> +	u32 pmcc;
>>> +	u32 booste_msk;
>>> +	u32 anaswvdd_msk;
>>>  };
>>>  
>>>  struct stm32_adc_priv;
>>> @@ -87,20 +113,26 @@ struct stm32_adc_priv_cfg {
>>>   * @domain:		irq domain reference
>>>   * @aclk:		clock reference for the analog circuitry
>>>   * @bclk:		bus clock common for all ADCs, depends on part used
>>> + * @vdd:		vdd supply reference
>>> + * @vdda:		vdda supply reference
>>>   * @vref:		regulator reference
>>>   * @cfg:		compatible configuration data
>>>   * @common:		common data for all ADC instances
>>>   * @ccr_bak:		backup CCR in low power mode
>>> + * @syscfg:		reference to syscon, system control registers
>>>   */
>>>  struct stm32_adc_priv {
>>>  	int				irq[STM32_ADC_MAX_ADCS];
>>>  	struct irq_domain		*domain;
>>>  	struct clk			*aclk;
>>>  	struct clk			*bclk;
>>> +	struct regulator		*vdd;
>>> +	struct regulator		*vdda;
>>>  	struct regulator		*vref;
>>>  	const struct stm32_adc_priv_cfg	*cfg;
>>>  	struct stm32_adc_common		common;
>>>  	u32				ccr_bak;
>>> +	struct regmap			*syscfg;
>>>  };
>>>  
>>>  static struct stm32_adc_priv *to_stm32_adc_priv(struct stm32_adc_common *com)
>>> @@ -284,6 +316,22 @@ static const struct stm32_adc_common_regs stm32h7_adc_common_regs = {
>>>  	.ccr = STM32H7_ADC_CCR,
>>>  	.eoc1_msk = STM32H7_EOC_MST,
>>>  	.eoc2_msk = STM32H7_EOC_SLV,
>>> +	.has_syscfg = HAS_VBOOSTER,
>>> +	.pmcr = STM32H7_SYSCFG_PMCR,
>>> +	.booste_msk = STM32H7_SYSCFG_BOOSTE_MASK,
>>> +};
>>> +
>>> +/* STM32MP1 common registers definitions */
>>> +static const struct stm32_adc_common_regs stm32mp1_adc_common_regs = {
>>> +	.csr = STM32H7_ADC_CSR,
>>> +	.ccr = STM32H7_ADC_CCR,
>>> +	.eoc1_msk = STM32H7_EOC_MST,
>>> +	.eoc2_msk = STM32H7_EOC_SLV,
>>> +	.has_syscfg =  HAS_VBOOSTER | HAS_ANASWVDD | HAS_CLEAR_REG,
>>
>> Extra space after =
> 
> Hi Jonathan,
> 
> Oops, I'll fix it in v2.
> 
>>
>>
>>> +	.pmcr = STM32MP1_SYSCFG_PMCSETR,
>>> +	.pmcc = STM32MP1_SYSCFG_PMCCLRR,
>>> +	.booste_msk = STM32H7_SYSCFG_BOOSTE_MASK,
>>> +	.anaswvdd_msk = STM32MP1_SYSCFG_ANASWVDD_MASK,
>>>  };
>>>  
>>>  /* ADC common interrupt for all instances */
>>> @@ -388,16 +436,145 @@ static void stm32_adc_irq_remove(struct platform_device *pdev,
>>>  	}
>>>  }
>>>  
>>> +static int stm32_adc_core_switches_supply_en(struct device *dev)
>>> +{
>>> +	struct stm32_adc_common *common = dev_get_drvdata(dev);
>>> +	struct stm32_adc_priv *priv = to_stm32_adc_priv(common);
>>> +	const struct stm32_adc_common_regs *regs = priv->cfg->regs;
>>> +	int ret, vdda, vdd = 0;
>>> +	u32 mask, clrmask, setmask = 0;
>>> +
>>> +	/*
>>> +	 * On STM32H7 and STM32MP1, the ADC inputs are multiplexed with analog
>>> +	 * switches (via PCSEL) which have reduced performances when their
>>> +	 * supply is below 2.7V (vdda by default):
>>> +	 * - Voltage booster can be used, to get full ADC performances
>>> +	 *   (increases power consumption).
>>> +	 * - Vdd can be used to supply them, if above 2.7V (STM32MP1 only).
>>> +	 *
>>> +	 * This is optional, as this is a trade-off between analog performance
>>> +	 * and power consumption.
>>> +	 */
>>> +	if (!regs->has_syscfg || !priv->vdda || !priv->syscfg) {
>>> +		dev_dbg(dev, "Not configuring analog switches\n");
>>> +		return 0;
>>> +	}
>>> +
>>> +	ret = regulator_enable(priv->vdda);
>>> +	if (ret < 0) {
>>> +		dev_err(dev, "vdda enable failed %d\n", ret);
>>> +		return ret;
>>> +	}
>>> +
>>> +	ret = regulator_get_voltage(priv->vdda);
>>> +	if (ret < 0) {
>>> +		dev_err(dev, "vdda get voltage failed %d\n", ret);
>>> +		goto vdda_dis;
>>> +	}
>>> +	vdda = ret;
>>> +
>> We only need to do the following block if vdaa is too low.  Should probably
>> not turn on vdd if there is not chance we are going to use it?
> 
> You're right, then I probably need to move the regulator_get_voltage()
> call at probe time, to avoid enabling it for nothing at runtime. (e.g.
> to figure out it's not going to be used).
> In fact, vdd is used also for other things on the platform (I/Os, other
> supplies...), and is marked "always-on" in the device tree. But I
> understand your point.
> 
> I'll rework this and send a v2.

Hi Jonathan,

When reworking this part, I figured out the vdda should be described as
required supply for the STM32 ADC. So I pushed out a fix series to
address this "Add missing vdda-supply to STM32 ADC". I'll resume v2 of
this series that has some dependencies on the fix series .

Thanks
Best Regards,
Fabrice

> 
> Thanks,
> Fabrice
> 
>>
>>> +	if (priv->vdd && regs->has_syscfg & HAS_ANASWVDD) {
>>> +		ret = regulator_enable(priv->vdd);
>>> +		if (ret < 0) {
>>> +			dev_err(dev, "vdd enable failed %d\n", ret);
>>> +			goto vdda_dis;
>>> +		}
>>> +
>>> +		ret = regulator_get_voltage(priv->vdd);
>>> +		if (ret < 0) {
>>> +			dev_err(dev, "vdd get voltage failed %d\n", ret);
>>> +			goto vdd_dis;
>>> +		}
>>> +		vdd = ret;
>>> +	}
>>> +
>>> +	/*
>>> +	 * Recommended settings for ANASWVDD and EN_BOOSTER:
>>> +	 * - vdda < 2.7V but vdd > 2.7V: ANASWVDD = 1, EN_BOOSTER = 0 (stm32mp1)
>>> +	 * - vdda < 2.7V and vdd < 2.7V: ANASWVDD = 0, EN_BOOSTER = 1
>>> +	 * - vdda >= 2.7V:               ANASWVDD = 0, EN_BOOSTER = 0 (default)
>>> +	 */
>>> +	if (vdda < 2700000) {
>>> +		if (vdd > 2700000) {
>>> +			dev_dbg(dev, "analog switches supplied by vdd\n");
>>> +			setmask = regs->anaswvdd_msk;
>>> +			clrmask = regs->booste_msk;
>>> +		} else {
>>> +			dev_dbg(dev, "Enabling voltage booster\n");
>>> +			setmask = regs->booste_msk;
>>> +			clrmask = regs->anaswvdd_msk;
>>> +		}
>>> +	} else {
>>> +		dev_dbg(dev, "analog switches supplied by vdda\n");
>>> +		clrmask = regs->booste_msk | regs->anaswvdd_msk;
>>> +	}
>>> +
>>> +	mask = regs->booste_msk | regs->anaswvdd_msk;
>>> +	if (regs->has_syscfg & HAS_CLEAR_REG) {
>>> +		ret = regmap_write(priv->syscfg, regs->pmcc, clrmask);
>>> +		if (ret) {
>>> +			dev_err(dev, "syscfg clear failed, %d\n", ret);
>>> +			goto vdd_dis;
>>> +		}
>>> +		mask = setmask;
>>> +	}
>>> +
>>> +	ret = regmap_update_bits(priv->syscfg, regs->pmcr, mask, setmask);
>>> +	if (ret) {
>>> +		dev_err(dev, "syscfg update failed, %d\n", ret);
>>> +		goto vdd_dis;
>>> +	}
>>> +
>>> +	/* Booster voltage can take up to 50 us to stabilize */
>>> +	if (setmask & regs->booste_msk)
>>> +		usleep_range(50, 100);
>>> +
>>> +	return ret;
>>> +
>>> +vdd_dis:
>>> +	if (priv->vdd && (regs->has_syscfg & HAS_ANASWVDD))
>>> +		regulator_disable(priv->vdd);
>>> +vdda_dis:
>>> +	regulator_disable(priv->vdda);
>>> +
>>> +	return ret;
>>> +}
>>> +
>>> +static void stm32_adc_core_switches_supply_dis(struct device *dev)
>>> +{
>>> +	struct stm32_adc_common *common = dev_get_drvdata(dev);
>>> +	struct stm32_adc_priv *priv = to_stm32_adc_priv(common);
>>> +	const struct stm32_adc_common_regs *regs = priv->cfg->regs;
>>> +	u32 mask = regs->booste_msk | regs->anaswvdd_msk;
>>> +
>>> +	if (!regs->has_syscfg || !priv->vdda || !priv->syscfg)
>>> +		return;
>>> +
>>> +	if (regs->has_syscfg & HAS_CLEAR_REG)
>>> +		regmap_write(priv->syscfg, regs->pmcc, mask);
>>> +	else
>>> +		regmap_update_bits(priv->syscfg, regs->pmcr, mask, 0);
>>> +
>>> +	if (priv->vdd && (regs->has_syscfg & HAS_ANASWVDD))
>>> +		regulator_disable(priv->vdd);
>>> +
>>> +	regulator_disable(priv->vdda);
>>> +}
>>> +
>>>  static int stm32_adc_core_hw_start(struct device *dev)
>>>  {
>>>  	struct stm32_adc_common *common = dev_get_drvdata(dev);
>>>  	struct stm32_adc_priv *priv = to_stm32_adc_priv(common);
>>>  	int ret;
>>>  
>>> +	ret = stm32_adc_core_switches_supply_en(dev);
>>> +	if (ret < 0)
>>> +		return ret;
>>> +
>>>  	ret = regulator_enable(priv->vref);
>>>  	if (ret < 0) {
>>>  		dev_err(dev, "vref enable failed\n");
>>> -		return ret;
>>> +		goto err_switches_disable;
>>>  	}
>>>  
>>>  	if (priv->bclk) {
>>> @@ -425,6 +602,8 @@ static int stm32_adc_core_hw_start(struct device *dev)
>>>  		clk_disable_unprepare(priv->bclk);
>>>  err_regulator_disable:
>>>  	regulator_disable(priv->vref);
>>> +err_switches_disable:
>>> +	stm32_adc_core_switches_supply_dis(dev);
>>>  
>>>  	return ret;
>>>  }
>>> @@ -441,6 +620,24 @@ static void stm32_adc_core_hw_stop(struct device *dev)
>>>  	if (priv->bclk)
>>>  		clk_disable_unprepare(priv->bclk);
>>>  	regulator_disable(priv->vref);
>>> +	stm32_adc_core_switches_supply_dis(dev);
>>> +}
>>> +
>>> +static int stm32_adc_core_syscfg_probe(struct device_node *np,
>>> +				       struct stm32_adc_priv *priv)
>>> +{
>>> +	if (!priv->cfg->regs->has_syscfg)
>>> +		return 0;
>>> +
>>> +	priv->syscfg = syscon_regmap_lookup_by_phandle(np, "st,syscfg");
>>> +	if (IS_ERR(priv->syscfg)) {
>>> +		/* Optional */
>>> +		if (PTR_ERR(priv->syscfg) != -ENODEV)
>>> +			return PTR_ERR(priv->syscfg);
>>> +		priv->syscfg = NULL;
>>> +	}
>>> +
>>> +	return 0;
>>>  }
>>>  
>>>  static int stm32_adc_probe(struct platform_device *pdev)
>>> @@ -475,6 +672,30 @@ static int stm32_adc_probe(struct platform_device *pdev)
>>>  		return ret;
>>>  	}
>>>  
>>> +	priv->vdda = devm_regulator_get_optional(&pdev->dev, "vdda");
>>> +	if (IS_ERR(priv->vdda)) {
>>> +		ret = PTR_ERR(priv->vdda);
>>> +		if (ret != -ENODEV) {
>>> +			if (ret != -EPROBE_DEFER)
>>> +				dev_err(&pdev->dev, "vdda get failed, %d\n",
>>> +					ret);
>>> +			return ret;
>>> +		}
>>> +		priv->vdda = NULL;
>>> +	}
>>> +
>>> +	priv->vdd = devm_regulator_get_optional(&pdev->dev, "vdd");
>>> +	if (IS_ERR(priv->vdd)) {
>>> +		ret = PTR_ERR(priv->vdd);
>>> +		if (ret != -ENODEV) {
>>> +			if (ret != -EPROBE_DEFER)
>>> +				dev_err(&pdev->dev, "vdd get failed, %d\n",
>>> +					ret);
>>> +			return ret;
>>> +		}
>>> +		priv->vdd = NULL;
>>> +	}
>>> +
>>>  	priv->aclk = devm_clk_get(&pdev->dev, "adc");
>>>  	if (IS_ERR(priv->aclk)) {
>>>  		ret = PTR_ERR(priv->aclk);
>>> @@ -495,6 +716,13 @@ static int stm32_adc_probe(struct platform_device *pdev)
>>>  		priv->bclk = NULL;
>>>  	}
>>>  
>>> +	ret = stm32_adc_core_syscfg_probe(np, priv);
>>> +	if (ret) {
>>> +		if (ret != -EPROBE_DEFER)
>>> +			dev_err(&pdev->dev, "Can't probe syscfg: %d\n", ret);
>>> +		return ret;
>>> +	}
>>> +
>>>  	pm_runtime_get_noresume(dev);
>>>  	pm_runtime_set_active(dev);
>>>  	pm_runtime_set_autosuspend_delay(dev, STM32_ADC_CORE_SLEEP_DELAY_MS);
>>> @@ -595,7 +823,7 @@ static const struct stm32_adc_priv_cfg stm32h7_adc_priv_cfg = {
>>>  };
>>>  
>>>  static const struct stm32_adc_priv_cfg stm32mp1_adc_priv_cfg = {
>>> -	.regs = &stm32h7_adc_common_regs,
>>> +	.regs = &stm32mp1_adc_common_regs,
>>>  	.clk_sel = stm32h7_adc_clk_sel,
>>>  	.max_clk_rate_hz = 40000000,
>>>  };
>>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel