From mboxrd@z Thu Jan  1 00:00:00 1970
From: bharat.kumar.gogada@xilinx.com (Bharat Kumar Gogada)
Date: Mon, 25 Jul 2016 05:23:58 +0000
Subject: Why does BIOS assign memory to 16 byte BAR
References: <8520D5D51A55D047800579B094147198258BB59B@XAP-PVEXMBX01.xlnx.xilinx.com>
 <20160722151546.GA20646@localhost> <20160722155133.GB20646@localhost>
Message-ID: <8520D5D51A55D047800579B094147198258BBC40@XAP-PVEXMBX01.xlnx.xilinx.com>
To: linux-arm-kernel@lists.infradead.org
List-Id: linux-arm-kernel.lists.infradead.org

> Subject: RE: Why does BIOS assign memory to 16 byte BAR
> 
> > Subject: Re: Why does BIOS assign memory to 16 byte BAR
> >
> > On Fri, Jul 22, 2016 at 10:15:46AM -0500, Bjorn Helgaas wrote:
> > > Hi Bharat,
> > >
> > > On Fri, Jul 22, 2016 at 09:24:22AM +0000, Bharat Kumar Gogada wrote:
> > > > Hi,
> > > >
> > > > I'm observing that on x86 BIOS successfully assigns memory if an End
> > > > point requests BAR of size 16byte.
> > > >
> > > > But as per Spec:
> > > > The minimum memory address range requested by a BAR is 128 bytes.
> > >
> > > Can you provide the spec reference for this?  I don't see it in PCI
> > > r3.0.
> > >
> > > PCI r3.0, sec 6.2.5.1, shows bits 4-31 of a memory BAR as writable,
> > > which would correspond to a minimum size of 16 bytes.
> >
> > The reference above is to the conventional PCI spec.  I happened to trip
> over
> > a note in PCIe r3.0, sec 1.3.2.2, that for a PCI Express endpoint, "the
> minimum
> > memory address range requested by a BAR is 128 bytes."
> >
> > I don't think linux currently enforces this minimum.
> >
> 
> Hi Bjorn Thanks for the reply.
> 
> Here is what the issue we are seeing.
> 
> We have total memory for BAR's on our SoC of 256 MB.
> When an End Point request individually 16 byte BAR's our root port assigns
> memory to BAR's successfully.
> 
> But if I have an End point which has 4 BAR's each 32 bit and request as
> following:
> When 1st BAR requests 1GB BAR it fails due to lack of memory. (We are
> running this as part of SIG compliance test case)
> 2nd BAR requests 1MB and other 2 BAR's request 16byte, but these are not
> getting BAR's assigned. (Even though BAR space is available, since 1GB failed,
> We have 256 MB still)
> 
> We have only one End point connected to our root port.
> 
> Here is the log:
> [    2.319289] nwl-pcie fd0e0000.pcie: Link is UP
> [    2.319332] PCI host bridge /amba/pcie at fd0e0000 ranges:
> [    2.319349]   No bus range found for /amba/pcie at fd0e0000, using [bus 00-
> ff]
> [    2.319374]    IO 0xe0000000..0xe000ffff -> 0x00000000
> [    2.319415]   MEM 0xe0100000..0xefffffff -> 0xe0100000
> [    2.319431]   MEM 0x600000000..0x7ffffffff -> 0x600000000
> [    2.319539] nwl-pcie fd0e0000.pcie: PCI host bridge to bus 0000:00
> [    2.319557] pci_bus 0000:00: root bus resource [bus 00-ff]
> [    2.319573] pci_bus 0000:00: root bus resource [io  0x0000-0xffff]
> [    2.319589] pci_bus 0000:00: root bus resource [mem 0xe0100000-0xefffffff]
> [    2.319606] pci_bus 0000:00: root bus resource [mem 0x600000000-
> 0x7ffffffff pref]
> [    2.319845] pci 0000:00:00.0: cannot attach to SMMU, is it on the same bus?
> [    2.319861] iommu: Adding device 0000:00:00.0 to group 1
> [    2.320243] pci 0000:01:00.0: cannot attach to SMMU, is it on the same bus?
> [    2.320258] iommu: Adding device 0000:01:00.0 to group 1
> [    2.320313] pci 0000:00:00.0: BAR 8: no space for [mem size 0x60000000]
> [    2.320331] pci 0000:00:00.0: BAR 8: failed to assign [mem size 0x60000000]
> [    2.320349] pci 0000:00:00.0: BAR 6: assigned [mem 0xe0100000-0xe01007ff
> pref]
> [    2.320374] pci 0000:01:00.0: BAR 0: no space for [mem size 0x40000000]
> [    2.320390] pci 0000:01:00.0: BAR 0: failed to assign [mem size 0x40000000]
> [    2.320407] pci 0000:01:00.0: BAR 4: no space for [mem size 0x00100000
> 64bit]
> [    2.320423] pci 0000:01:00.0: BAR 4: failed to assign [mem size 0x00100000
> 64bit]
> [    2.320446] pci 0000:01:00.0: BAR 2: no space for [mem size 0x00000010]
> [    2.320461] pci 0000:01:00.0: BAR 2: failed to assign [mem size 0x00000010]
> [    2.320477] pci 0000:01:00.0: BAR 3: no space for [mem size 0x00000010]
> [    2.320493] pci 0000:01:00.0: BAR 3: failed to assign [mem size 0x00000010]
> [    2.320509] pci 0000:00:00.0: PCI bridge to [bus 01-0c]
> 
> Please let me know, what might might be the issue.
> 

Adding to the above will kernel allocate other memory BARs to an End Point if 
one BAR assignment fails ?

What if the End Point has multiple function and say first function BAR assignment failed,
will the kernel assign BAR's to second function on same bus and device ?  

Thanks & Regards,
Bharat