From: Neil Armstrong <narmstrong@baylibre.com>
To: Jerome Brunet <jbrunet@baylibre.com>
Cc: linux-amlogic@lists.infradead.org, linux-clk@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org
Subject: Re: [PATCH 4/4] clk: meson: axg: add MIPI DSI Host clock
Date: Thu, 10 Sep 2020 13:48:26 +0200 [thread overview]
Message-ID: <8e7bb5fe-4332-6983-bb64-612cc7ae8256@baylibre.com> (raw)
In-Reply-To: <1jwo129btu.fsf@starbuckisacylon.baylibre.com>
On 10/09/2020 12:15, Jerome Brunet wrote:
>
> On Mon 07 Sep 2020 at 11:38, Neil Armstrong <narmstrong@baylibre.com> wrote:
>
>> This adds the MIPI DSI Host clock, used to measure the signal timings (ENC VSYNC or
>> DW-MIPI-DSI eDPI timings).
>>
>> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
>> ---
>> drivers/clk/meson/axg.c | 66 +++++++++++++++++++++++++++++++++++++++++
>> drivers/clk/meson/axg.h | 4 ++-
>> 2 files changed, 69 insertions(+), 1 deletion(-)
>>
>> diff --git a/drivers/clk/meson/axg.c b/drivers/clk/meson/axg.c
>> index 2550616c14b0..0094ca6388d8 100644
>> --- a/drivers/clk/meson/axg.c
>> +++ b/drivers/clk/meson/axg.c
>> @@ -1724,6 +1724,66 @@ static struct clk_regmap axg_cts_encl = {
>> },
>> };
>>
>> +/* MIPI DSI Host Clock */
>> +
>> +static const struct clk_parent_data axg_vdin_meas_parent_data[] = {
>> + { .fw_name = "xtal", },
>> + { .hw = &axg_fclk_div4.hw },
>> + { .hw = &axg_fclk_div3.hw },
>> + { .hw = &axg_fclk_div5.hw },
>> + { },
>> + { },
>
> As you've done in other patches, I'd prefer if you used an index table
> instead of having empty entries.
>
>> + { .hw = &axg_fclk_div2.hw },
>> + { .hw = &axg_fclk_div7.hw },
>> +};
OK, will do
>> +
>> +static struct clk_regmap axg_vdin_meas_sel = {
>> + .data = &(struct clk_regmap_mux_data){
>> + .offset = HHI_VDIN_MEAS_CLK_CNTL,
>> + .mask = 0x7,
>> + .shift = 21,
>> + .flags = CLK_MUX_ROUND_CLOSEST,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "vdin_meas_sel",
>> + .ops = &clk_regmap_mux_ops,
>> + .parent_data = axg_vdin_meas_parent_data,
>> + .num_parents = ARRAY_SIZE(axg_vdin_meas_parent_data),
>> + .flags = CLK_SET_RATE_NO_REPARENT,
>
> A comment about why manual control is required would be nice.
This is a typo, will remove.
>
>> + },
>> +};
>> +
>> +static struct clk_regmap axg_vdin_meas_div = {
>> + .data = &(struct clk_regmap_div_data){
>> + .offset = HHI_VDIN_MEAS_CLK_CNTL,
>> + .shift = 12,
>> + .width = 7,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "vdin_meas_div",
>> + .ops = &clk_regmap_divider_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &axg_vdin_meas_sel.hw },
>> + .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT,
>> + },
>> +};
>> +
>> +static struct clk_regmap axg_vdin_meas = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = HHI_VDIN_MEAS_CLK_CNTL,
>> + .bit_idx = 20,
>> + },
>> + .hw.init = &(struct clk_init_data) {
>> + .name = "vdin_meas",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &axg_vdin_meas_div.hw },
>> + .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT,
>> + },
>> +};
>> +
>> static u32 mux_table_gen_clk[] = { 0, 4, 5, 6, 7, 8,
>> 9, 10, 11, 13, 14, };
>> static const struct clk_parent_data gen_clk_parent_data[] = {
>> @@ -1987,6 +2047,9 @@ static struct clk_hw_onecell_data axg_hw_onecell_data = {
>> [CLKID_VCLK2_DIV12] = &axg_vclk2_div12.hw,
>> [CLKID_CTS_ENCL_SEL] = &axg_cts_encl_sel.hw,
>> [CLKID_CTS_ENCL] = &axg_cts_encl.hw,
>> + [CLKID_VDIN_MEAS_SEL] = &axg_vdin_meas_sel.hw,
>> + [CLKID_VDIN_MEAS_DIV] = &axg_vdin_meas_div.hw,
>> + [CLKID_VDIN_MEAS] = &axg_vdin_meas.hw,
>> [NR_CLKS] = NULL,
>> },
>> .num = NR_CLKS,
>> @@ -2115,6 +2178,9 @@ static struct clk_regmap *const axg_clk_regmaps[] = {
>> &axg_vclk2_div12_en,
>> &axg_cts_encl_sel,
>> &axg_cts_encl,
>> + &axg_vdin_meas_sel,
>> + &axg_vdin_meas_div,
>> + &axg_vdin_meas,
>> };
>>
>> static const struct meson_eeclkc_data axg_clkc_data = {
>> diff --git a/drivers/clk/meson/axg.h b/drivers/clk/meson/axg.h
>> index a8787b394a47..481b307ea3cb 100644
>> --- a/drivers/clk/meson/axg.h
>> +++ b/drivers/clk/meson/axg.h
>> @@ -158,8 +158,10 @@
>> #define CLKID_VCLK2_DIV6_EN 120
>> #define CLKID_VCLK2_DIV12_EN 121
>> #define CLKID_CTS_ENCL_SEL 132
>> +#define CLKID_VDIN_MEAS_SEL 134
>> +#define CLKID_VDIN_MEAS_DIV 135
>>
>> -#define NR_CLKS 134
>> +#define NR_CLKS 137
>>
>> /* include the CLKIDs that have been made part of the DT binding */
>> #include <dt-bindings/clock/axg-clkc.h>
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
prev parent reply other threads:[~2020-09-10 11:49 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-09-07 9:38 [PATCH 0/4] clk: meson: axg: add clocks for MIPI-DSI support Neil Armstrong
2020-09-07 9:38 ` [PATCH 1/4] dt-bindings: clk: axg-clkc: add Video Clocks Neil Armstrong
2020-09-07 9:38 ` [PATCH 2/4] dt-bindings: clk: axg-clkc: add MIPI DSI Host clock binding Neil Armstrong
2020-09-07 9:38 ` [PATCH 3/4] clk: meson: axg: add Video Clocks Neil Armstrong
2020-09-10 10:13 ` Jerome Brunet
2020-09-10 11:47 ` Neil Armstrong
2020-09-11 17:10 ` Kevin Hilman
2020-09-07 9:38 ` [PATCH 4/4] clk: meson: axg: add MIPI DSI Host clock Neil Armstrong
2020-09-10 10:15 ` Jerome Brunet
2020-09-10 11:48 ` Neil Armstrong [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=8e7bb5fe-4332-6983-bb64-612cc7ae8256@baylibre.com \
--to=narmstrong@baylibre.com \
--cc=jbrunet@baylibre.com \
--cc=linux-amlogic@lists.infradead.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).