Re: [PATCH v4 4/6] PM / devfreq: Add dynamic scaling for imx8m ddr controller

[Chanwoo Choi <cw00.choi@samsung.com>]

Hi Leonard,

On 11/9/19 7:39 AM, Leonard Crestez wrote:
> Add driver for dynamic scaling the DDR Controller on imx8m chips. Actual
> frequency switching is implemented inside TF-A, this driver wraps the
> SMC calls and synchronizes the clk tree.
> 
> The DRAM clocks on imx8m have the following structure (abridged):
> 
>  +----------+       |\            +------+
>  | dram_pll |-------|M| dram_core |      |
>  +----------+       |U|---------->| D    |
>                  /--|X|           |  D   |
>    dram_alt_root |  |/            |   R  |
>                  |                |    C |
>             +---------+           |      |
>             |FIX DIV/4|           |      |
>             +---------+           |      |
>   composite:     |                |      |
>  +----------+    |                |      |
>  | dram_alt |----/                |      |
>  +----------+                     |      |
>  | dram_apb |-------------------->|      |
>  +----------+                     +------+
> 
> The dram_pll is used for higher rates and dram_alt is used for lower
> rates. The dram_alt and dram_apb clocks are "imx composite" and their
> parent can also be modified.
> 
> This driver will prepare/enable the new parents ahead of switching (so
> that the expected roots are enabled) and afterwards it will call
> clk_set_parent to ensure the parents in clock framework are up-to-date.
> 
> The driver relies on dram_pll dram_alt and dram_apb being marked with
> CLK_GET_RATE_NOCACHE for rate updates.
> 
> Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
> ---
>  drivers/devfreq/Kconfig      |  10 +
>  drivers/devfreq/Makefile     |   1 +
>  drivers/devfreq/imx8m-ddrc.c | 416 +++++++++++++++++++++++++++++++++++
>  3 files changed, 427 insertions(+)
>  create mode 100644 drivers/devfreq/imx8m-ddrc.c
> 
> diff --git a/drivers/devfreq/Kconfig b/drivers/devfreq/Kconfig
> index defe1d438710..c519fd27808f 100644
> --- a/drivers/devfreq/Kconfig
> +++ b/drivers/devfreq/Kconfig
> @@ -90,10 +90,20 @@ config ARM_EXYNOS_BUS_DEVFREQ
>  	  Each memory bus group could contain many memoby bus block. It reads
>  	  PPMU counters of memory controllers by using DEVFREQ-event device
>  	  and adjusts the operating frequencies and voltages with OPP support.
>  	  This does not yet operate with optimal voltages.
>  
> +config ARM_IMX8M_DDRC_DEVFREQ
> +	tristate "i.MX8M DDRC DEVFREQ Driver"
> +	depends on ARCH_MXC || COMPILE_TEST
> +	select DEVFREQ_GOV_SIMPLE_ONDEMAND
> +	select DEVFREQ_GOV_USERSPACE
> +	select PM_OPP

It doesn't need to add. CONFIG_DEVFREQ add 'select PM_OPP'
because 'PM_OPP' is mandatory for devfreq.

> +	help
> +	  This adds the DEVFREQ driver for the i.MX8M DDR Controller. It allows
> +	  adjusting DRAM frequency.
> +
>  config ARM_TEGRA_DEVFREQ
>  	tristate "NVIDIA Tegra30/114/124/210 DEVFREQ Driver"
>  	depends on ARCH_TEGRA_3x_SOC || ARCH_TEGRA_114_SOC || \
>  		ARCH_TEGRA_132_SOC || ARCH_TEGRA_124_SOC || \
>  		ARCH_TEGRA_210_SOC || \
> diff --git a/drivers/devfreq/Makefile b/drivers/devfreq/Makefile
> index 338ae8440db6..3eb4d5e6635c 100644
> --- a/drivers/devfreq/Makefile
> +++ b/drivers/devfreq/Makefile
> @@ -7,10 +7,11 @@ obj-$(CONFIG_DEVFREQ_GOV_POWERSAVE)	+= governor_powersave.o
>  obj-$(CONFIG_DEVFREQ_GOV_USERSPACE)	+= governor_userspace.o
>  obj-$(CONFIG_DEVFREQ_GOV_PASSIVE)	+= governor_passive.o
>  
>  # DEVFREQ Drivers
>  obj-$(CONFIG_ARM_EXYNOS_BUS_DEVFREQ)	+= exynos-bus.o
> +obj-$(CONFIG_ARM_IMX8M_DDRC_DEVFREQ)	+= imx8m-ddrc.o
>  obj-$(CONFIG_ARM_RK3399_DMC_DEVFREQ)	+= rk3399_dmc.o
>  obj-$(CONFIG_ARM_TEGRA_DEVFREQ)		+= tegra30-devfreq.o
>  obj-$(CONFIG_ARM_TEGRA20_DEVFREQ)	+= tegra20-devfreq.o
>  
>  # DEVFREQ Event Drivers
> diff --git a/drivers/devfreq/imx8m-ddrc.c b/drivers/devfreq/imx8m-ddrc.c
> new file mode 100644
> index 000000000000..51903fee21a7
> --- /dev/null
> +++ b/drivers/devfreq/imx8m-ddrc.c
> @@ -0,0 +1,416 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright 2019 NXP
> + */
> +
> +#include <linux/module.h>
> +#include <linux/device.h>
> +#include <linux/of_device.h>
> +#include <linux/platform_device.h>
> +#include <linux/devfreq.h>
> +#include <linux/pm_opp.h>
> +#include <linux/clk.h>
> +#include <linux/clk-provider.h>
> +#include <linux/arm-smccc.h>
> +
> +#define IMX_SIP_DDR_DVFS			0xc2000004
> +
> +/* Values starting from 0 switch to specific frequency */
> +#define IMX_SIP_DDR_FREQ_SET_HIGH		0x00
> +
> +/* Deprecated after moving IRQ handling to ATF */
> +#define IMX_SIP_DDR_DVFS_WAIT_CHANGE		0x0F
> +
> +/* Query available frequencies. */
> +#define IMX_SIP_DDR_DVFS_GET_FREQ_COUNT		0x10
> +#define IMX_SIP_DDR_DVFS_GET_FREQ_INFO		0x11
> +
> +/*
> + * This should be in a 1:1 mapping with devicetree OPPs but
> + * firmware provides additional info.
> + */
> +struct imx8m_ddrc_freq {
> +	unsigned long rate;
> +	unsigned long smcarg;
> +	int dram_core_parent_index;
> +	int dram_alt_parent_index;
> +	int dram_apb_parent_index;
> +};
> +
> +/* Hardware limitation */
> +#define IMX8M_DDRC_MAX_FREQ_COUNT 4
> +
> +/*
> + * i.MX8M DRAM Controller clocks have the following structure (abridged):
> + *
> + * +----------+       |\            +------+
> + * | dram_pll |-------|M| dram_core |      |
> + * +----------+       |U|---------->| D    |
> + *                 /--|X|           |  D   |
> + *   dram_alt_root |  |/            |   R  |
> + *                 |                |    C |
> + *            +---------+           |      |
> + *            |FIX DIV/4|           |      |
> + *            +---------+           |      |
> + *  composite:     |                |      |
> + * +----------+    |                |      |
> + * | dram_alt |----/                |      |
> + * +----------+                     |      |
> + * | dram_apb |-------------------->|      |
> + * +----------+                     +------+
> + *
> + * The dram_pll is used for higher rates and dram_alt is used for lower rates.
> + *
> + * Frequency switching is implemented in TF-A (via SMC call) and can change the
> + * configuration of the clocks, including mux parents. The dram_alt and
> + * dram_apb clocks are "imx composite" and their parent can change too.
> + *
> + * We need to prepare/enable the new mux parents head of switching and update
> + * their information afterwards.
> + */
> +struct imx8m_ddrc {
> +	struct devfreq_dev_profile profile;
> +	struct devfreq *devfreq;
> +
> +	/* For frequency switching: */
> +	struct clk *dram_core;
> +	struct clk *dram_pll;
> +	struct clk *dram_alt;
> +	struct clk *dram_apb;
> +
> +	int freq_count;
> +	struct imx8m_ddrc_freq freq_table[IMX8M_DDRC_MAX_FREQ_COUNT];
> +};
> +
> +static struct imx8m_ddrc_freq *imx8m_ddrc_find_freq(struct imx8m_ddrc *priv,
> +						    unsigned long rate)
> +{
> +	struct imx8m_ddrc_freq *freq;
> +	int i;
> +
> +	/*
> +	 * Firmware reports values in MT/s, so we round-down from Hz
> +	 * Rounding is extra generous to ensure a match.
> +	 */
> +	rate = DIV_ROUND_CLOSEST(rate, 250000);
> +	for (i = 0; i < priv->freq_count; ++i) {
> +		freq = &priv->freq_table[i];
> +		if (freq->rate == rate ||
> +				freq->rate + 1 == rate ||
> +				freq->rate - 1 == rate)
> +			return freq;
> +	}
> +
> +	return NULL;
> +}
> +
> +static void imx8m_ddrc_smc_set_freq(int target_freq)
> +{
> +	struct arm_smccc_res res;
> +	u32 online_cpus = 0;
> +	int cpu;
> +
> +	local_irq_disable();

local_irq_disable is more proper than local_irq_save()?

> +
> +	for_each_online_cpu(cpu)
> +		online_cpus |= (1 << (cpu * 8));
> +
> +	/* change the ddr freqency */
> +	arm_smccc_smc(IMX_SIP_DDR_DVFS, target_freq, online_cpus,
> +			0, 0, 0, 0, 0, &res);
> +
> +	local_irq_enable();

ditto. local_irq_restore() instead of local_irq_enable()

> +}
> +
> +struct clk *clk_get_parent_by_index(struct clk *clk, int index)
> +{
> +	struct clk_hw *hw;
> +
> +	hw = clk_hw_get_parent_by_index(__clk_get_hw(clk), index);
> +
> +	return hw ? hw->clk : NULL;
> +}
> +
> +static int imx8m_ddrc_set_freq(struct device *dev, struct imx8m_ddrc_freq *freq)
> +{
> +	struct imx8m_ddrc *priv = dev_get_drvdata(dev);
> +	struct clk *new_dram_core_parent;
> +	struct clk *new_dram_alt_parent;
> +	struct clk *new_dram_apb_parent;
> +	int ret;
> +
> +	new_dram_core_parent = clk_get_parent_by_index(

You can use 'clk_hw_get_parent_by_index' directly.
And, you need to check whether the return value is NULL or not.

> +			priv->dram_core, freq->dram_core_parent_index - 1);
> +	new_dram_alt_parent = clk_get_parent_by_index(

ditto.

> +			priv->dram_alt, freq->dram_alt_parent_index - 1);
> +	new_dram_apb_parent = clk_get_parent_by_index(

ditto.

> +			priv->dram_apb, freq->dram_apb_parent_index - 1);
> +
> +	/* increase reference counts and ensure clks are ON before switch */
> +	ret = clk_prepare_enable(new_dram_core_parent);
> +	if (ret) {
> +		dev_err(dev, "failed enable new dram_core parent: %d\n", ret);
> +		goto out;
> +	}
> +	ret = clk_prepare_enable(new_dram_alt_parent);
> +	if (ret) {
> +		dev_err(dev, "failed enable new dram_alt parent: %d\n", ret);
> +		goto out_dis_core;

I think that 'dis' is not general expression for 'disable'.
Just, I think that 'out_disable_core' is better than 'out_dis_core'.

> +	}
> +	ret = clk_prepare_enable(new_dram_apb_parent);
> +	if (ret) {
> +		dev_err(dev, "failed enable new dram_apb parent: %d\n", ret);
> +		goto out_dis_alt;

ditto.

> +	}
> +
> +	imx8m_ddrc_smc_set_freq(freq->smcarg);
> +
> +	/* update parents in clk tree after switch. */
> +	ret = clk_set_parent(priv->dram_core, new_dram_core_parent);
> +	if (ret)
> +		dev_err(dev, "failed set dram_core parent: %d\n", ret);

if you don't return directly, you better to use 'dev_warn' instead of 'dev_err'.

> +	if (new_dram_alt_parent) {
> +		ret = clk_set_parent(priv->dram_alt, new_dram_alt_parent);
> +		if (ret)
> +			dev_err(dev, "failed set dram_alt parent: %d\n", ret);

ditto. Use dev_warn.
 
> +	}
> +	if (new_dram_apb_parent) {
> +		ret = clk_set_parent(priv->dram_apb, new_dram_apb_parent);
> +		if (ret)
> +			dev_err(dev, "failed set dram_apb parent: %d\n", ret);

ditto. Use dev_warn.

> +	}
> +
> +	/*
> +	 * Explicitly refresh dram PLL rate.
> +	 *
> +	 * Even if it's marked with CLK_GET_RATE_NOCACHE the rate will not be

nitpick:
What is more proper description either or 'Even if' or 'if' ?

> +	 * automatically refreshed when clk_get_rate is called on children.
> +	 */
> +	clk_get_rate(priv->dram_pll);
> +
> +	/*
> +	 * clk_set_parent transfer the reference count from old parent.
> +	 * now we drop extra reference counts used during the switch
> +	 */
> +	clk_disable_unprepare(new_dram_apb_parent);
> +out_dis_alt:
> +	clk_disable_unprepare(new_dram_alt_parent);
> +out_dis_core:
> +	clk_disable_unprepare(new_dram_core_parent);
> +out:
> +	return ret;
> +}
> +
> +static int imx8m_ddrc_target(struct device *dev, unsigned long *freq, u32 flags)
> +{
> +	struct imx8m_ddrc *priv = dev_get_drvdata(dev);
> +	struct imx8m_ddrc_freq *freq_info;
> +	struct dev_pm_opp *new_opp;
> +	unsigned long old_freq, new_freq;
> +	int ret;
> +
> +	new_opp = devfreq_recommended_opp(dev, freq, flags);
> +	if (IS_ERR(new_opp)) {
> +		ret = PTR_ERR(new_opp);
> +		dev_err(dev, "failed to get recommended opp: %d\n", ret);
> +		return ret;
> +	}
> +	dev_pm_opp_put(new_opp);
> +
> +	old_freq = clk_get_rate(priv->dram_core);
> +	if (*freq == old_freq)
> +		return 0;
> +
> +	freq_info = imx8m_ddrc_find_freq(priv, *freq);
> +	if (!freq_info)
> +		return -EINVAL;
> +	ret = imx8m_ddrc_set_freq(dev, freq_info);

Need to check whether 'ret' is valid or not.

> +
> +	/* Also read back the clk rate to verify switch was correct */
> +	new_freq = clk_get_rate(priv->dram_core);
> +	if (ret || *freq != new_freq)

You should check 'ret' right after imx8m_ddrc_set_freq()
instead of this position.

> +		dev_err(dev, "ddrc failed freq set to %lu from %lu, now at %lu\n",
> +			old_freq, *freq, new_freq);
> +	else
> +		dev_dbg(dev, "ddrc freq set to %lu (was %lu)\n",
> +			*freq, old_freq);
> +
> +	return ret;
> +}
> +
> +static int imx8m_ddrc_get_cur_freq(struct device *dev, unsigned long *freq)
> +{
> +	struct imx8m_ddrc *priv = dev_get_drvdata(dev);
> +
> +	*freq = clk_get_rate(priv->dram_core);
> +
> +	return 0;
> +}
> +
> +static int imx8m_ddrc_init_freq_info(struct device *dev)
> +{
> +	struct imx8m_ddrc *priv = dev_get_drvdata(dev);
> +	struct arm_smccc_res res;
> +	int index;
> +
> +	/*
> +	 * An error here means DDR DVFS API not supported by firmware
> +	 */

Don't need to add multiple line comments. It is possible to be change as following:

	/* An error here means DDR DVFS API not supported by firmware */

> +	arm_smccc_smc(IMX_SIP_DDR_DVFS, IMX_SIP_DDR_DVFS_GET_FREQ_COUNT,
> +			0, 0, 0, 0, 0, 0, &res);
> +	priv->freq_count = res.a0;
> +	if (priv->freq_count <= 0 ||
> +			priv->freq_count > IMX8M_DDRC_MAX_FREQ_COUNT)
> +		return -ENODEV;
> +
> +	for (index = 0; index < priv->freq_count; ++index) {
> +		struct imx8m_ddrc_freq *freq = &priv->freq_table[index];
> +
> +		arm_smccc_smc(IMX_SIP_DDR_DVFS, IMX_SIP_DDR_DVFS_GET_FREQ_INFO,
> +				index, 0, 0, 0, 0, 0, &res);
> +		/* Result should be strictly positive */
> +		if ((long)res.a0 <= 0)
> +			return -ENODEV;
> +
> +		freq->rate = res.a0;
> +		freq->smcarg = index;
> +		freq->dram_core_parent_index = res.a1;
> +		freq->dram_alt_parent_index = res.a2;
> +		freq->dram_apb_parent_index = res.a3;
> +
> +		/* dram_core has 2 options: dram_pll or dram_alt_root */
> +		if (freq->dram_core_parent_index != 1 &&
> +				freq->dram_core_parent_index != 2)
> +			return -ENODEV;
> +		/* dram_apb and dram_alt have exactly 8 possible parents */
> +		if (freq->dram_alt_parent_index > 8 ||
> +				freq->dram_apb_parent_index > 8)
> +			return -ENODEV;
> +		/* dram_core from alt requires explicit dram_alt parent */
> +		if (freq->dram_core_parent_index == 2 &&
> +				freq->dram_alt_parent_index == 0)
> +			return -ENODEV;
> +	}
> +
> +	return 0;
> +}
> +
> +/* imx8m_ddrc_check_opps() - disable OPPs not supported by firmware */

nitpick:
On this driver, there are no some description for internal function.
In order to keep the coding style, you better to move this comment
into function before 'freq = ULONG_MAX'.

> +static int imx8m_ddrc_check_opps(struct device *dev)
> +{
> +	struct imx8m_ddrc *priv = dev_get_drvdata(dev);
> +	struct imx8m_ddrc_freq *freq_info;
> +	struct dev_pm_opp *opp;
> +	unsigned long freq;
> +
> +	freq = ULONG_MAX;
> +	while (true) {
> +		opp = dev_pm_opp_find_freq_floor(dev, &freq);
> +		if (opp == ERR_PTR(-ERANGE))
> +			break;
> +		if (IS_ERR(opp)) {
> +			dev_err(dev, "Failed enumerating OPPs: %ld\n",
> +				PTR_ERR(opp));
> +			return PTR_ERR(opp);
> +		}
> +		dev_pm_opp_put(opp);
> +
> +		freq_info = imx8m_ddrc_find_freq(priv, freq);
> +		if (!freq_info) {
> +			dev_info(dev, "Disable unsupported OPP %luHz %luMT/s\n",
> +					freq, DIV_ROUND_CLOSEST(freq, 250000));
> +			dev_pm_opp_disable(dev, freq);
> +		}
> +
> +		freq--;
> +	}
> +
> +	return 0;
> +}
> +
> +static void imx8m_ddrc_exit(struct device *dev)
> +{
> +	dev_pm_opp_of_remove_table(dev);
> +}
> +
> +static int imx8m_ddrc_probe(struct platform_device *pdev)
> +{
> +	struct device *dev = &pdev->dev;
> +	struct imx8m_ddrc *priv;
> +	const char *gov = DEVFREQ_GOV_USERSPACE;
> +	int ret;
> +
> +	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> +	if (!priv)
> +		return -ENOMEM;
> +
> +	platform_set_drvdata(pdev, priv);
> +
> +	ret = imx8m_ddrc_init_freq_info(dev);
> +	if (ret) {
> +		dev_err(dev, "failed to init firmware freq info: %d\n", ret);
> +		return ret;
> +	}
> +
> +	priv->dram_core = devm_clk_get(dev, "core");
> +	priv->dram_pll = devm_clk_get(dev, "pll");
> +	priv->dram_alt = devm_clk_get(dev, "alt");
> +	priv->dram_apb = devm_clk_get(dev, "apb");
> +	if (IS_ERR(priv->dram_core) ||
> +		IS_ERR(priv->dram_pll) ||
> +		IS_ERR(priv->dram_alt) ||
> +		IS_ERR(priv->dram_apb)) {
> +		ret = PTR_ERR(priv->devfreq);
> +		dev_err(dev, "failed to fetch clocks: %d\n", ret);
> +		return ret;
> +	}
> +
> +	ret = dev_pm_opp_of_add_table(dev);
> +	if (ret < 0) {
> +		dev_err(dev, "failed to get OPP table\n");
> +		return ret;
> +	}
> +
> +	ret = imx8m_ddrc_check_opps(dev);
> +	if (ret < 0)
> +		goto err;
> +
> +	priv->profile.polling_ms = 1000;
> +	priv->profile.target = imx8m_ddrc_target;
> +	priv->profile.exit = imx8m_ddrc_exit;
> +	priv->profile.get_cur_freq = imx8m_ddrc_get_cur_freq;
> +	priv->profile.initial_freq = clk_get_rate(priv->dram_core);
> +
> +	priv->devfreq = devm_devfreq_add_device(dev, &priv->profile,
> +						gov, NULL);
> +	if (IS_ERR(priv->devfreq)) {
> +		ret = PTR_ERR(priv->devfreq);
> +		dev_err(dev, "failed to add devfreq device: %d\n", ret);
> +		goto err;
> +	}
> +
> +	return 0;
> +
> +err:
> +	dev_pm_opp_of_remove_table(dev);
> +	return ret;
> +}
> +
> +static const struct of_device_id imx8m_ddrc_of_match[] = {
> +	{ .compatible = "fsl,imx8m-ddrc", },
> +	{ /* sentinel */ },
> +};
> +MODULE_DEVICE_TABLE(of, imx8m_ddrc_of_match);
> +
> +static struct platform_driver imx8m_ddrc_platdrv = {
> +	.probe		= imx8m_ddrc_probe,
> +	.driver = {
> +		.name	= "imx8m-ddrc-devfreq",
> +		.of_match_table = of_match_ptr(imx8m_ddrc_of_match),
> +	},
> +};
> +module_platform_driver(imx8m_ddrc_platdrv);
> +
> +MODULE_DESCRIPTION("i.MX8M DDR Controller frequency driver");
> +MODULE_AUTHOR("Leonard Crestez <leonard.crestez@nxp.com>");
> +MODULE_LICENSE("GPL v2");
> 


-- 
Best Regards,
Chanwoo Choi
Samsung Electronics

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel