On Thu, Sep 10, 2020 at 3:08 PM Florian Fainelli <f.fainelli@gmail.com> wrote:
>
>
>
> On 9/10/2020 12:05 PM, Jim Quinlan wrote:
> > On Thu, Sep 10, 2020 at 2:50 PM Rob Herring <robh@kernel.org> wrote:
> >>
> >> On Thu, Sep 10, 2020 at 10:42 AM Jim Quinlan <james.quinlan@broadcom.com> wrote:
> >>>
> >>> On Thu, Sep 10, 2020 at 11:56 AM Rob Herring <robh@kernel.org> wrote:
> >>>>
> >>>> On Mon, Aug 24, 2020 at 03:30:17PM -0400, Jim Quinlan wrote:
> >>>>> From: Jim Quinlan <jquinlan@broadcom.com>
> >>>>>
> >>>>> Broadcom Set-top (BrcmSTB) boards typically support S2, S3, and S5 suspend
> >>>>> and resume.  Now the PCIe driver may do so as well.
> >>>>>
> >>>>> Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
> >>>>> Acked-by: Florian Fainelli <f.fainelli@gmail.com>
> >>>>> ---
> >>>>>   drivers/pci/controller/pcie-brcmstb.c | 47 +++++++++++++++++++++++++++
> >>>>>   1 file changed, 47 insertions(+)
> >>>>>
> >>>>> diff --git a/drivers/pci/controller/pcie-brcmstb.c b/drivers/pci/controller/pcie-brcmstb.c
> >>>>> index c2b3d2946a36..3d588ab7a6dd 100644
> >>>>> --- a/drivers/pci/controller/pcie-brcmstb.c
> >>>>> +++ b/drivers/pci/controller/pcie-brcmstb.c
> >>>>> @@ -978,6 +978,47 @@ static void brcm_pcie_turn_off(struct brcm_pcie *pcie)
> >>>>>        brcm_pcie_bridge_sw_init_set(pcie, 1);
> >>>>>   }
> >>>>>
> >>>>> +static int brcm_pcie_suspend(struct device *dev)
> >>>>> +{
> >>>>> +     struct brcm_pcie *pcie = dev_get_drvdata(dev);
> >>>>> +
> >>>>> +     brcm_pcie_turn_off(pcie);
> >>>>> +     clk_disable_unprepare(pcie->clk);
> >>>>> +
> >>>>> +     return 0;
> >>>>> +}
> >>>>> +
> >>>>> +static int brcm_pcie_resume(struct device *dev)
> >>>>> +{
> >>>>> +     struct brcm_pcie *pcie = dev_get_drvdata(dev);
> >>>>> +     void __iomem *base;
> >>>>> +     u32 tmp;
> >>>>> +     int ret;
> >>>>> +
> >>>>> +     base = pcie->base;
> >>>>> +     clk_prepare_enable(pcie->clk);
> >>>>> +
> >>>>> +     /* Take bridge out of reset so we can access the SERDES reg */
> >>>>> +     brcm_pcie_bridge_sw_init_set(pcie, 0);
> >>>>> +
> >>>>> +     /* SERDES_IDDQ = 0 */
> >>>>> +     tmp = readl(base + PCIE_MISC_HARD_PCIE_HARD_DEBUG);
> >>>>> +     u32p_replace_bits(&tmp, 0, PCIE_MISC_HARD_PCIE_HARD_DEBUG_SERDES_IDDQ_MASK);
> >>>>> +     writel(tmp, base + PCIE_MISC_HARD_PCIE_HARD_DEBUG);
> >>>>> +
> >>>>> +     /* wait for serdes to be stable */
> >>>>> +     udelay(100);
> >>>>
> >>>> Really needs to be a spinloop?
> >>>>
> >>>>> +
> >>>>> +     ret = brcm_pcie_setup(pcie);
> >>>>> +     if (ret)
> >>>>> +             return ret;
> >>>>> +
> >>>>> +     if (pcie->msi)
> >>>>> +             brcm_msi_set_regs(pcie->msi);
> >>>>> +
> >>>>> +     return 0;
> >>>>> +}
> >>>>> +
> >>>>>   static void __brcm_pcie_remove(struct brcm_pcie *pcie)
> >>>>>   {
> >>>>>        brcm_msi_remove(pcie);
> >>>>> @@ -1087,12 +1128,18 @@ static int brcm_pcie_probe(struct platform_device *pdev)
> >>>>>
> >>>>>   MODULE_DEVICE_TABLE(of, brcm_pcie_match);
> >>>>>
> >>>>> +static const struct dev_pm_ops brcm_pcie_pm_ops = {
> >>>>> +     .suspend_noirq = brcm_pcie_suspend,
> >>>>> +     .resume_noirq = brcm_pcie_resume,
> >>>>
> >>>> Why do you need interrupts disabled? There's 39 cases of .suspend_noirq
> >>>> and 1352 of .suspend in the tree.
> >>>
> >>> I will test switching this to  suspend_late/resume_early.
> >>
> >> Why not just the 'regular' flavor suspend/resume?
> >>
> >> Rob
> > We must have our PCIe driver suspend last and resume first because our
> > current driver turns off/on the power for the EPs.  Note that this
> > code isn't in the driver as we are still figuring out a way to make it
> > upstreamable.
>
> The suspend/resume ordering should be guaranteed by the Linux device
> driver model though if not, this is a bug that ought to be fixed. The
> PCI bridge sits at the top of the pci_device list and all EPs should be
> child devices, so the suspend order should be from EPs down to the
> bridge, and the resume the converse.
I remembered that after I hit send.
Jim
> --
> Florian