linux-arm-kernel.lists.infradead.org archive mirror
 help / color / mirror / Atom feed
From: anilk4.v@gmail.com (Anil Kumar)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH V4] ARM: dts: add minimal DT support for DevKit8000.
Date: Wed, 6 Mar 2013 08:06:02 +0530	[thread overview]
Message-ID: <CABYxbz62JrMB95p5i9iu2G=B4ETXLrYbLsyFEFR5F+WVD6YNnQ@mail.gmail.com> (raw)
In-Reply-To: <F3DBB1B3EF102E4994C89758CFCA32412CC74F@DBDE01.ent.ti.com>

Hi Tony,

>> From: linux-arm-kernel [mailto:linux-arm-kernel-
>> bounces at lists.infradead.org] On Behalf Of Anil Kumar
>> Sent: Wednesday, February 27, 2013 8:03 AM
>> To: devicetree-discuss at lists.ozlabs.org; linux-omap at vger.kernel.org;
>> linux-kernel at vger.kernel.org; linux-arm-kernel at lists.infradead.org
>> Cc: linux at arm.linux.org.uk; Cousson, Benoit; Tony Lindgren; Grant
>> Likely; Anil Kumar; thomas at tomweber.eu
>> Subject: Re: FW: [PATCH V4] ARM: dts: add minimal DT support for
>> DevKit8000.
>>
>> Hi,
>> >
>> > DevKit8000 is a beagle board clone from Timll, sold by
>> > armkits.com. The DevKit8000 has RS232 serial port, LCD, DVI-D,
>> > S-Video, Ethernet, SD/MMC, keyboard, camera, SPI, I2C, USB and
>> > JTAG interface.
>> >
>> > This patch adds the basic DT support for devkit8000. At this time,
>> Information
>> > of twl4030 (PMIC), MMC1, I2C1 and leds are added.
>> >
>> > Signed-off-by: Anil Kumar <anilk4.v@gmail.com>
>> > Tested-by: Thomas Weber <thomas@tomweber.eu>
>>
>> Gentle Ping. As there are no review comments on this patch,
>> Could you please pull this patch ?

Gentle Ping.

This patch also got Reviewed-by: Manish Badarkhe <badarkhe.manish@gmail.com>
and as patch "ARM: dts: omap3-devkit8000: Enable audio support"  has already got
"Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>" but it is on the
top of this patch.
So, Could you please pull this patch in one of your omap branch? or
you want me to
do rebase this patch on top of v3.9-rc1 ?

Thanks,
Anil

>>
>> > ---
>> >  -This patch is based on top of kernel 3.8-rc5.
>> >
>> >  -Tested on Devkit8000.
>> >
>> > For V4:
>> >  -Tiny nitpick.
>> >
>> > For V3:
>> >  - Remove pin mux as done at device boot time by default.
>> >
>> > For V2:
>> >  - Change model name as "TimLL OMAP3 Devkit8000"
>> >  - Change compatible as "timll,omap3-devkit8000"
>> >  - Doing i2c1 pinmux default with pinctrl-single driver instead of
>> i2c1
>> >    driver probe time.
>> >
>> > :100644 100644 5ebb44f... 22ebc76... M  arch/arm/boot/dts/Makefile
>> > :000000 100644 0000000... 2e1463a... A  arch/arm/boot/dts/omap3-
>> devkit8000.dts
>> > :100644 100644 53cb380b.. ccecb76... M  arch/arm/mach-omap2/board-
>> generic.c
>> >  arch/arm/boot/dts/Makefile             |    1 +
>> >  arch/arm/boot/dts/omap3-devkit8000.dts |  102
>> ++++++++++++++++++++++++++++++++
>> >  arch/arm/mach-omap2/board-generic.c    |    1 +
>> >  3 files changed, 104 insertions(+), 0 deletions(-)
>> >
>> > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>> > index 5ebb44f..22ebc76 100644
>> > --- a/arch/arm/boot/dts/Makefile
>> > +++ b/arch/arm/boot/dts/Makefile
>> > @@ -102,6 +102,7 @@ dtb-$(CONFIG_ARCH_MXS) += imx23-evk.dtb \
>> >         imx28-tx28.dtb
>> >  dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
>> >         omap3-beagle.dtb \
>> > +       omap3-devkit8000.dtb \
>> >         omap3-beagle-xm.dtb \
>> >         omap3-evm.dtb \
>> >         omap3-tobi.dtb \
>> > diff --git a/arch/arm/boot/dts/omap3-devkit8000.dts
>> b/arch/arm/boot/dts/omap3-devkit8000.dts
>> > new file mode 100644
>> > index 0000000..2e1463a
>> > --- /dev/null
>> > +++ b/arch/arm/boot/dts/omap3-devkit8000.dts
>> > @@ -0,0 +1,102 @@
>> > +/*
>> > + * Author: Anil Kumar <anilk4.v@gmail.com>
>> > + *
>> > + * This program is free software; you can redistribute it and/or
>> modify
>> > + * it under the terms of the GNU General Public License version 2 as
>> > + * published by the Free Software Foundation.
>> > + */
>> > +/dts-v1/;
>> > +
>> > +/include/ "omap3.dtsi"
>> > +/ {
>> > +       model = "TimLL OMAP3 Devkit8000";
>> > +       compatible = "timll,omap3-devkit8000", "ti,omap3";
>> > +
>> > +       memory {
>> > +               device_type = "memory";
>> > +               reg = <0x80000000 0x10000000>;  /* 256 MB */
>> > +       };
>> > +
>> > +       leds {
>> > +               compatible = "gpio-leds";
>> > +
>> > +               heartbeat {
>> > +                       label = "devkit8000::led1";
>> > +                       gpios = <&gpio6 26 0>;  /* 186 -> LED1 */
>> > +                       default-state = "on";
>> > +                       linux,default-trigger = "heartbeat";
>> > +               };
>> > +
>> > +               mmc {
>> > +                       label = "devkit8000::led2";
>> > +                       gpios = <&gpio6 3 0>;   /* 163 -> LED2 */
>> > +                       default-state = "on";
>> > +                       linux,default-trigger = "none";
>> > +               };
>> > +
>> > +               usr {
>> > +                       label = "devkit8000::led3";
>> > +                       gpios = <&gpio6 4 0>;   /* 164 -> LED3 */
>> > +                       default-state = "on";
>> > +                       linux,default-trigger = "usr";
>> > +                };
>> > +       };
>> > +};
>> > +
>> > +&i2c1 {
>> > +       clock-frequency = <2600000>;
>> > +
>> > +       twl: twl at 48 {
>> > +               reg = <0x48>;
>> > +               interrupts = <7>;       /* SYS_NIRQ cascaded to intc
>> */
>> > +               interrupt-parent = <&intc>;
>> > +       };
>> > +};
>> > +
>> > +&i2c2 {
>> > +       status = "disabled";
>> > +};
>> > +
>> > +&i2c3 {
>> > +       status = "disabled";
>> > +};
>> > +
>> > +/include/ "twl4030.dtsi"
>> > +
>> > +&mmc1 {
>> > +       vmmc-supply = <&vmmc1>;
>> > +       vmmc_aux-supply = <&vsim>;
>> > +       bus-width = <8>;
>> > +};
>> > +
>> > +&mmc2 {
>> > +       status = "disabled";
>> > +};
>> > +
>> > +&mmc3 {
>> > +       status = "disabled";
>> > +};
>> > +
>> > +&wdt2 {
>> > +       status = "disabled";
>> > +};
>> > +
>> > +&mcbsp1 {
>> > +       status = "disabled";
>> > +};
>> > +
>> > +&mcbsp2 {
>> > +       status = "disabled";
>> > +};
>> > +
>> > +&mcbsp3 {
>> > +       status = "disabled";
>> > +};
>> > +
>> > +&mcbsp4 {
>> > +       status = "disabled";
>> > +};
>> > +
>> > +&mcbsp5 {
>> > +       status = "disabled";
>> > +};
>> > diff --git a/arch/arm/mach-omap2/board-generic.c b/arch/arm/mach-
>> omap2/board-generic.c
>> > index 53cb380..ccecb76 100644
>> > --- a/arch/arm/mach-omap2/board-generic.c
>> > +++ b/arch/arm/mach-omap2/board-generic.c
>> > @@ -110,6 +110,7 @@ MACHINE_END
>> >
>> >  static const char *omap3_gp_boards_compat[] __initdata = {
>> >         "ti,omap3-beagle",
>> > +       "timll,omap3-devkit8000",
>> >         NULL,
>> >  };
>> >
>> > --
>> > 1.7.0.4
>> >
>> >
>> > _______________________________________________
>> > linux-arm-kernel mailing list
>> > linux-arm-kernel at lists.infradead.org
>> > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>>
>> _______________________________________________
>> linux-arm-kernel mailing list
>> linux-arm-kernel at lists.infradead.org
>> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

  parent reply	other threads:[~2013-03-06  2:36 UTC|newest]

Thread overview: 9+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
     [not found] <F3DBB1B3EF102E4994C89758CFCA32412CC4E9@DBDE01.ent.ti.com>
2013-02-27  2:33 ` FW: [PATCH V4] ARM: dts: add minimal DT support for DevKit8000 Anil Kumar
     [not found]   ` <F3DBB1B3EF102E4994C89758CFCA32412CC74F@DBDE01.ent.ti.com>
2013-03-06  2:36     ` Anil Kumar [this message]
2013-03-06 17:53       ` Tony Lindgren
2013-03-07  6:51         ` Benoit Cousson
2013-03-07 16:10           ` Tony Lindgren
2013-03-17  5:23           ` Anil Kumar
2013-03-18 15:21             ` Benoit Cousson
2013-02-20 13:44 Anil Kumar
2013-02-20 15:02 ` Manish Badarkhe

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to='CABYxbz62JrMB95p5i9iu2G=B4ETXLrYbLsyFEFR5F+WVD6YNnQ@mail.gmail.com' \
    --to=anilk4.v@gmail.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).