linux-arm-kernel.lists.infradead.org archive mirror
 help / color / mirror / Atom feed
* [PATCH v3 00/11] add hisilicon SoC support
@ 2013-03-13  5:05 Haojian Zhuang
  2013-03-13  5:05 ` [PATCH v3 01/11] clocksource: move sp timer driver Haojian Zhuang
                   ` (10 more replies)
  0 siblings, 11 replies; 44+ messages in thread
From: Haojian Zhuang @ 2013-03-13  5:05 UTC (permalink / raw)
  To: linux-arm-kernel

Changelog:
v3:
   1. Replace to call hs_init_clocks() in hi3xxx.c by of_clk_init().
   2. Add CLK_OF_DECLARE() in clk-hi3xxx driver.
   3. Add "select USE_OF" for CONFIG_CLKSRC_OF configuration. So drop CONFIG_OF in sp804 driver.
   4. Move readme file into driver patch.
   5. Append "arm,integrator-timer" for sp804 match table.
v2:
   1. Rename mach-hs to mach-hi3xxx.
   2. Remove CONFIG_MACH_HS_DT.
   3. Move sp804 dual timer driver into drivers/clocksource.
   4. Make sp804 driver to support DT. Append CLOCKSOURCE_OF_DECLARE() in sp804 driver.
   5. Update hisilicon,hi3620-clkgate & hisilicon,hi3620-clkrst property in clk-hi3xxx driver.

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 01/11] clocksource: move sp timer driver
  2013-03-13  5:05 [PATCH v3 00/11] add hisilicon SoC support Haojian Zhuang
@ 2013-03-13  5:05 ` Haojian Zhuang
  2013-03-13  5:05 ` [PATCH v3 02/11] clocksource: select USE_OF by default Haojian Zhuang
                   ` (9 subsequent siblings)
  10 siblings, 0 replies; 44+ messages in thread
From: Haojian Zhuang @ 2013-03-13  5:05 UTC (permalink / raw)
  To: linux-arm-kernel

All clocksource drivers should be moved into drivers/clocksource
directory, since it's necessary for integrating them into clocksource_of
infrastructure.

Move ARM SP804 timer driver from arch/arm directory into
drivers/clocksource directory.

Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
---
 arch/arm/Kconfig                                                  |    5 -----
 arch/arm/common/Makefile                                          |    1 -
 arch/arm/mach-highbank/highbank.c                                 |    4 ++--
 arch/arm/mach-integrator/integrator_ap.c                          |    2 +-
 arch/arm/mach-integrator/integrator_cp.c                          |    4 ++--
 arch/arm/mach-realview/core.c                                     |    4 ++--
 arch/arm/mach-versatile/core.c                                    |    4 ++--
 arch/arm/mach-vexpress/ct-ca9x4.c                                 |    5 ++---
 arch/arm/mach-vexpress/v2m.c                                      |    4 ++--
 drivers/clocksource/Kconfig                                       |    5 +++++
 drivers/clocksource/Makefile                                      |    1 +
 {arch/arm/common => drivers/clocksource}/timer-sp.c               |    2 +-
 .../arm/include/asm/hardware => include/clocksource}/arm_timer.h  |    4 ++--
 {arch/arm/include/asm/hardware => include/clocksource}/timer-sp.h |    4 ++++
 14 files changed, 26 insertions(+), 23 deletions(-)
 rename {arch/arm/common => drivers/clocksource}/timer-sp.c (99%)
 rename {arch/arm/include/asm/hardware => include/clocksource}/arm_timer.h (93%)
 rename {arch/arm/include/asm/hardware => include/clocksource}/timer-sp.h (87%)

diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 2363926..10d7e2c 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -1177,11 +1177,6 @@ config PLAT_PXA
 config PLAT_VERSATILE
 	bool
 
-config ARM_TIMER_SP804
-	bool
-	select CLKSRC_MMIO
-	select HAVE_SCHED_CLOCK
-
 source arch/arm/mm/Kconfig
 
 config ARM_NR_BANKS
diff --git a/arch/arm/common/Makefile b/arch/arm/common/Makefile
index 45f7eae..a4e49e7 100644
--- a/arch/arm/common/Makefile
+++ b/arch/arm/common/Makefile
@@ -12,4 +12,3 @@ obj-$(CONFIG_SHARP_LOCOMO)	+= locomo.o
 obj-$(CONFIG_SHARP_PARAM)	+= sharpsl_param.o
 obj-$(CONFIG_SHARP_SCOOP)	+= scoop.o
 obj-$(CONFIG_PCI_HOST_ITE8152)  += it8152.o
-obj-$(CONFIG_ARM_TIMER_SP804)	+= timer-sp.o
diff --git a/arch/arm/mach-highbank/highbank.c b/arch/arm/mach-highbank/highbank.c
index a4f9f50..cfd843b 100644
--- a/arch/arm/mach-highbank/highbank.c
+++ b/arch/arm/mach-highbank/highbank.c
@@ -27,14 +27,14 @@
 #include <linux/smp.h>
 #include <linux/amba/bus.h>
 #include <linux/clk-provider.h>
+#include <clocksource/arm_timer.h>
+#include <clocksource/timer-sp.h>
 
 #include <asm/arch_timer.h>
 #include <asm/cacheflush.h>
 #include <asm/cputype.h>
 #include <asm/smp_plat.h>
 #include <asm/smp_twd.h>
-#include <asm/hardware/arm_timer.h>
-#include <asm/hardware/timer-sp.h>
 #include <asm/hardware/cache-l2x0.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
diff --git a/arch/arm/mach-integrator/integrator_ap.c b/arch/arm/mach-integrator/integrator_ap.c
index ea96144..c2112ff 100644
--- a/arch/arm/mach-integrator/integrator_ap.c
+++ b/arch/arm/mach-integrator/integrator_ap.c
@@ -41,11 +41,11 @@
 #include <linux/stat.h>
 #include <linux/sys_soc.h>
 #include <linux/termios.h>
+#include <clocksource/arm_timer.h>
 #include <video/vga.h>
 
 #include <mach/hardware.h>
 #include <mach/platform.h>
-#include <asm/hardware/arm_timer.h>
 #include <asm/setup.h>
 #include <asm/param.h>		/* HZ */
 #include <asm/mach-types.h>
diff --git a/arch/arm/mach-integrator/integrator_cp.c b/arch/arm/mach-integrator/integrator_cp.c
index 2b0db82..40373ec 100644
--- a/arch/arm/mach-integrator/integrator_cp.c
+++ b/arch/arm/mach-integrator/integrator_cp.c
@@ -28,12 +28,13 @@
 #include <linux/of_address.h>
 #include <linux/of_platform.h>
 #include <linux/sys_soc.h>
+#include <clocksource/arm_timer.h>
+#include <clocksource/timer-sp.h>
 
 #include <mach/hardware.h>
 #include <mach/platform.h>
 #include <asm/setup.h>
 #include <asm/mach-types.h>
-#include <asm/hardware/arm_timer.h>
 #include <asm/hardware/icst.h>
 
 #include <mach/cm.h>
@@ -45,7 +46,6 @@
 #include <asm/mach/map.h>
 #include <asm/mach/time.h>
 
-#include <asm/hardware/timer-sp.h>
 
 #include <plat/clcd.h>
 #include <plat/sched_clock.h>
diff --git a/arch/arm/mach-realview/core.c b/arch/arm/mach-realview/core.c
index 1d5ee5c..26a3da38 100644
--- a/arch/arm/mach-realview/core.c
+++ b/arch/arm/mach-realview/core.c
@@ -31,11 +31,12 @@
 #include <linux/amba/mmci.h>
 #include <linux/gfp.h>
 #include <linux/mtd/physmap.h>
+#include <clocksource/arm_timer.h>
+#include <clocksource/timer-sp.h>
 
 #include <mach/hardware.h>
 #include <asm/irq.h>
 #include <asm/mach-types.h>
-#include <asm/hardware/arm_timer.h>
 #include <asm/hardware/icst.h>
 
 #include <asm/mach/arch.h>
@@ -45,7 +46,6 @@
 
 #include <mach/platform.h>
 #include <mach/irqs.h>
-#include <asm/hardware/timer-sp.h>
 
 #include <plat/clcd.h>
 #include <plat/sched_clock.h>
diff --git a/arch/arm/mach-versatile/core.c b/arch/arm/mach-versatile/core.c
index 25160ae..e894a1f 100644
--- a/arch/arm/mach-versatile/core.c
+++ b/arch/arm/mach-versatile/core.c
@@ -38,9 +38,10 @@
 #include <linux/clkdev.h>
 #include <linux/mtd/physmap.h>
 #include <linux/bitops.h>
+#include <clocksource/arm_timer.h>
+#include <clocksource/timer-sp.h>
 
 #include <asm/irq.h>
-#include <asm/hardware/arm_timer.h>
 #include <asm/hardware/icst.h>
 #include <asm/mach-types.h>
 
@@ -50,7 +51,6 @@
 #include <asm/mach/map.h>
 #include <mach/hardware.h>
 #include <mach/platform.h>
-#include <asm/hardware/timer-sp.h>
 
 #include <plat/clcd.h>
 #include <plat/sched_clock.h>
diff --git a/arch/arm/mach-vexpress/ct-ca9x4.c b/arch/arm/mach-vexpress/ct-ca9x4.c
index 6f34497..48f6676 100644
--- a/arch/arm/mach-vexpress/ct-ca9x4.c
+++ b/arch/arm/mach-vexpress/ct-ca9x4.c
@@ -11,16 +11,15 @@
 #include <linux/clkdev.h>
 #include <linux/vexpress.h>
 #include <linux/irqchip/arm-gic.h>
+#include <clocksource/arm_timer.h>
+#include <clocksource/timer-sp.h>
 
-#include <asm/hardware/arm_timer.h>
 #include <asm/hardware/cache-l2x0.h>
 #include <asm/smp_scu.h>
 #include <asm/smp_twd.h>
 
 #include <mach/ct-ca9x4.h>
 
-#include <asm/hardware/timer-sp.h>
-
 #include <asm/mach/map.h>
 #include <asm/mach/time.h>
 
diff --git a/arch/arm/mach-vexpress/v2m.c b/arch/arm/mach-vexpress/v2m.c
index 915683c..51e8701 100644
--- a/arch/arm/mach-vexpress/v2m.c
+++ b/arch/arm/mach-vexpress/v2m.c
@@ -21,6 +21,8 @@
 #include <linux/regulator/fixed.h>
 #include <linux/regulator/machine.h>
 #include <linux/vexpress.h>
+#include <clocksource/arm_timer.h>
+#include <clocksource/timer-sp.h>
 
 #include <asm/arch_timer.h>
 #include <asm/mach-types.h>
@@ -29,9 +31,7 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 #include <asm/mach/time.h>
-#include <asm/hardware/arm_timer.h>
 #include <asm/hardware/cache-l2x0.h>
-#include <asm/hardware/timer-sp.h>
 
 #include <mach/ct-ca9x4.h>
 #include <mach/motherboard.h>
diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig
index e8c4532..4c04d19 100644
--- a/drivers/clocksource/Kconfig
+++ b/drivers/clocksource/Kconfig
@@ -63,6 +63,11 @@ config CLKSRC_DBX500_PRCMU_SCHED_CLOCK
 config ARM_ARCH_TIMER
 	bool
 
+config ARM_TIMER_SP804
+	bool
+	select CLKSRC_MMIO
+	select HAVE_SCHED_CLOCK
+
 config CLKSRC_METAG_GENERIC
 	def_bool y if METAG
 	help
diff --git a/drivers/clocksource/Makefile b/drivers/clocksource/Makefile
index 1c1b15d..9d3ad88 100644
--- a/drivers/clocksource/Makefile
+++ b/drivers/clocksource/Makefile
@@ -22,4 +22,5 @@ obj-$(CONFIG_VT8500_TIMER)	+= vt8500_timer.o
 obj-$(CONFIG_CLKSRC_EXYNOS_MCT)	+= exynos_mct.o
 
 obj-$(CONFIG_ARM_ARCH_TIMER)		+= arm_arch_timer.o
+obj-$(CONFIG_ARM_TIMER_SP804)		+= timer-sp.o
 obj-$(CONFIG_CLKSRC_METAG_GENERIC)	+= metag_generic.o
diff --git a/arch/arm/common/timer-sp.c b/drivers/clocksource/timer-sp.c
similarity index 99%
rename from arch/arm/common/timer-sp.c
rename to drivers/clocksource/timer-sp.c
index 9d2d3ba..a7f2510 100644
--- a/arch/arm/common/timer-sp.c
+++ b/drivers/clocksource/timer-sp.c
@@ -25,9 +25,9 @@
 #include <linux/interrupt.h>
 #include <linux/irq.h>
 #include <linux/io.h>
+#include <clocksource/arm_timer.h>
 
 #include <asm/sched_clock.h>
-#include <asm/hardware/arm_timer.h>
 
 static long __init sp804_get_clock_rate(const char *name)
 {
diff --git a/arch/arm/include/asm/hardware/arm_timer.h b/include/clocksource/arm_timer.h
similarity index 93%
rename from arch/arm/include/asm/hardware/arm_timer.h
rename to include/clocksource/arm_timer.h
index d6030ff..f4a443a 100644
--- a/arch/arm/include/asm/hardware/arm_timer.h
+++ b/include/clocksource/arm_timer.h
@@ -1,5 +1,5 @@
-#ifndef __ASM_ARM_HARDWARE_ARM_TIMER_H
-#define __ASM_ARM_HARDWARE_ARM_TIMER_H
+#ifndef __CLOCKSOURCE_ARM_TIMER_H
+#define __CLOCKSOURCE_ARM_TIMER_H
 
 /*
  * ARM timer implementation, found in Integrator, Versatile and Realview
diff --git a/arch/arm/include/asm/hardware/timer-sp.h b/include/clocksource/timer-sp.h
similarity index 87%
rename from arch/arm/include/asm/hardware/timer-sp.h
rename to include/clocksource/timer-sp.h
index 2dd9d3f..0ad4186 100644
--- a/arch/arm/include/asm/hardware/timer-sp.h
+++ b/include/clocksource/timer-sp.h
@@ -1,3 +1,6 @@
+#ifndef __TIMER_SP_H
+#define __TIMER_SP_H
+
 void __sp804_clocksource_and_sched_clock_init(void __iomem *,
 					      const char *, int);
 
@@ -13,3 +16,4 @@ static inline void sp804_clocksource_and_sched_clock_init(void __iomem *base,
 }
 
 void sp804_clockevents_init(void __iomem *, unsigned int, const char *);
+#endif	/* __TIMER_SP_H */
-- 
1.7.10.4

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 02/11] clocksource: select USE_OF by default
  2013-03-13  5:05 [PATCH v3 00/11] add hisilicon SoC support Haojian Zhuang
  2013-03-13  5:05 ` [PATCH v3 01/11] clocksource: move sp timer driver Haojian Zhuang
@ 2013-03-13  5:05 ` Haojian Zhuang
  2013-03-13  5:05 ` [PATCH v3 03/11] clocksource: sp804: add device tree support Haojian Zhuang
                   ` (8 subsequent siblings)
  10 siblings, 0 replies; 44+ messages in thread
From: Haojian Zhuang @ 2013-03-13  5:05 UTC (permalink / raw)
  To: linux-arm-kernel

Since clksrc_of driver is always used in DT mode, select CONFIG_USE_OF
by default. It could avoid build issue.

Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
---
 drivers/clocksource/Kconfig |    1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig
index 4c04d19..167ed92 100644
--- a/drivers/clocksource/Kconfig
+++ b/drivers/clocksource/Kconfig
@@ -1,4 +1,5 @@
 config CLKSRC_OF
+	select USE_OF
 	bool
 
 config CLKSRC_I8253
-- 
1.7.10.4

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 03/11] clocksource: sp804: add device tree support
  2013-03-13  5:05 [PATCH v3 00/11] add hisilicon SoC support Haojian Zhuang
  2013-03-13  5:05 ` [PATCH v3 01/11] clocksource: move sp timer driver Haojian Zhuang
  2013-03-13  5:05 ` [PATCH v3 02/11] clocksource: select USE_OF by default Haojian Zhuang
@ 2013-03-13  5:05 ` Haojian Zhuang
  2013-03-13 11:05   ` Pawel Moll
  2013-03-13  5:05 ` [PATCH v3 04/11] ARM: integrator: use clocksource_of_init for sp804 Haojian Zhuang
                   ` (7 subsequent siblings)
  10 siblings, 1 reply; 44+ messages in thread
From: Haojian Zhuang @ 2013-03-13  5:05 UTC (permalink / raw)
  To: linux-arm-kernel

Parse clock & irq from device tree for sp804.

Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
---
 .../devicetree/bindings/timer/arm,sp804.txt        |   27 +++++
 drivers/clocksource/timer-sp.c                     |  105 ++++++++++++++++++++
 2 files changed, 132 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/timer/arm,sp804.txt

diff --git a/Documentation/devicetree/bindings/timer/arm,sp804.txt b/Documentation/devicetree/bindings/timer/arm,sp804.txt
new file mode 100644
index 0000000..ec1ae45
--- /dev/null
+++ b/Documentation/devicetree/bindings/timer/arm,sp804.txt
@@ -0,0 +1,27 @@
+ARM sp804 Dual Timers
+---------------------------------------
+
+Required properties:
+- compatible: Should be "arm,sp804" & "arm,primecell"
+- interrupts: Should contain the list of Dual Timer interrupts
+	interrupts = <0 0 4>, <0 1 4>;
+- reg: Should contain location and length for dual timer register.
+- clocks: clock driving the dual timer hardware
+	clocks = <&timclk0 &timclk1>;
+
+Optional properties:
+- arm,sp804-clocksource: Should contain the register offset of TIMER1 or
+  TIMER2 in Dual Timer Controller.
+	arm,sp804-clocksource = <0x20>;
+
+Example:
+
+	timer0: timer at fc800000 {
+		compatible = "arm,sp804", "arm,primecell";
+		reg = <0xfc800000 0x1000>;
+		/* timer00 & timer01 */
+		interrupts = <0 0 4>, <0 1 4>;
+		clocks = <&timclk0 &timclk1>;
+		clock-names = "apb_pclk";
+		status = "disabled";
+	};
diff --git a/drivers/clocksource/timer-sp.c b/drivers/clocksource/timer-sp.c
index a7f2510..63f757d 100644
--- a/drivers/clocksource/timer-sp.c
+++ b/drivers/clocksource/timer-sp.c
@@ -19,16 +19,23 @@
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
  */
 #include <linux/clk.h>
+#include <linux/clkdev.h>
 #include <linux/clocksource.h>
 #include <linux/clockchips.h>
 #include <linux/err.h>
 #include <linux/interrupt.h>
 #include <linux/irq.h>
 #include <linux/io.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
 #include <clocksource/arm_timer.h>
+#include <clocksource/timer-sp.h>
 
 #include <asm/sched_clock.h>
 
+#define SP804_CLKSRC	"sp804 source"
+#define SP804_CLKEVT	"sp804 event"
+
 static long __init sp804_get_clock_rate(const char *name)
 {
 	struct clk *clk;
@@ -189,3 +196,101 @@ void __init sp804_clockevents_init(void __iomem *base, unsigned int irq,
 	setup_irq(irq, &sp804_timer_irq);
 	clockevents_config_and_register(evt, rate, 0xf, 0xffffffff);
 }
+
+static struct device_node *from = NULL;
+
+static struct of_device_id sp804_timer_match[] __initdata = {
+	{ .compatible = "arm,sp804", },
+	{}
+};
+
+static struct clk __init *sp804_dt_init_clk(struct device_node *np, int i,
+					    const char *name)
+{
+	struct clk_lookup *lookup = NULL;
+	struct clk *clk;
+
+	clk = of_clk_get(np, i);
+	if (IS_ERR(clk))
+		return clk;
+	lookup = clkdev_alloc(clk, name, "sp804");
+	if (!lookup) {
+		clk_put(clk);
+		return ERR_PTR(-EINVAL);
+	}
+	clkdev_add(lookup);
+	return clk;
+}
+
+static void __attribute__((__unused__)) __init sp804_dt_init(void)
+{
+	struct device_node *np = NULL;
+	struct clk *clksrc = NULL, *clkevt = NULL;
+	void __iomem *base;
+	int retsrc, retevt, i = 0, irq = 0;
+	u32 srcoffs = 0, evtoffs = 0;
+
+	np = of_find_matching_node(from, sp804_timer_match);
+	WARN_ON(!np);
+	if (!np) {
+		pr_err("Failed to find sp804 timer\n");
+		return;
+	}
+	from = np;
+	/* check whether timer node is available */
+	if (!of_device_is_available(np))
+		return;
+
+	base = of_iomap(np, 0);
+	WARN_ON(!base);
+	if (!base)
+		return;
+
+	retsrc = of_property_read_u32(np, "arm,sp804-clocksource", &srcoffs);
+	retevt = of_property_read_u32(np, "arm,sp804-clockevent", &evtoffs);
+	if (retsrc < 0 && retevt < 0)
+		goto err;
+
+	if (!retsrc) {
+		if (srcoffs) {
+			/* TIMER2 is clock source */
+			i = 1;
+			srcoffs = TIMER_2_BASE;
+		} else {
+			/* TIMER1 is clock source */
+			i = 0;
+			srcoffs = TIMER_1_BASE;
+		}
+		clksrc = sp804_dt_init_clk(np, i, SP804_CLKSRC);
+		if (IS_ERR(clksrc))
+			goto err;
+		sp804_clocksource_and_sched_clock_init(base + srcoffs,
+						       SP804_CLKSRC);
+	}
+	if (!retevt) {
+		if (evtoffs) {
+			/* TIMER2 is clock event */
+			i = 1;
+			evtoffs = TIMER_2_BASE;
+		} else {
+			/* TIMER1 is clock event */
+			i = 0;
+			evtoffs = TIMER_1_BASE;
+		}
+		irq = irq_of_parse_and_map(np, i);
+		if (irq < 0)
+			goto err_evt;
+		clkevt = sp804_dt_init_clk(np, i, SP804_CLKEVT);
+		if (IS_ERR(clkevt))
+			goto err_evt;
+		sp804_clockevents_init(base + evtoffs, irq, SP804_CLKEVT);
+	}
+
+	return;
+err_evt:
+	if (clksrc)
+		clk_put(clksrc);
+err:
+	iounmap(base);
+}
+CLOCKSOURCE_OF_DECLARE(sp804, "arm,sp804", sp804_dt_init)
-- 
1.7.10.4

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 04/11] ARM: integrator: use clocksource_of_init for sp804
  2013-03-13  5:05 [PATCH v3 00/11] add hisilicon SoC support Haojian Zhuang
                   ` (2 preceding siblings ...)
  2013-03-13  5:05 ` [PATCH v3 03/11] clocksource: sp804: add device tree support Haojian Zhuang
@ 2013-03-13  5:05 ` Haojian Zhuang
  2013-03-13  5:05 ` [PATCH v3 05/11] ARM: highbank: " Haojian Zhuang
                   ` (6 subsequent siblings)
  10 siblings, 0 replies; 44+ messages in thread
From: Haojian Zhuang @ 2013-03-13  5:05 UTC (permalink / raw)
  To: linux-arm-kernel

Remove all code to parse sp804 in integrator platform driver. Use
clocksource_of_init() instead since these code are implemented in sp804
driver already.

Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
---
 arch/arm/boot/dts/integrator.dtsi        |    3 +++
 arch/arm/boot/dts/integratorap.dts       |    9 +++----
 arch/arm/boot/dts/integratorcp.dts       |    9 +++----
 arch/arm/mach-integrator/Kconfig         |    3 +++
 arch/arm/mach-integrator/integrator_ap.c |   41 +-----------------------------
 arch/arm/mach-integrator/integrator_cp.c |   35 ++-----------------------
 drivers/clocksource/timer-sp.c           |    2 ++
 7 files changed, 19 insertions(+), 83 deletions(-)

diff --git a/arch/arm/boot/dts/integrator.dtsi b/arch/arm/boot/dts/integrator.dtsi
index 813b91d..749ac21 100644
--- a/arch/arm/boot/dts/integrator.dtsi
+++ b/arch/arm/boot/dts/integrator.dtsi
@@ -9,18 +9,21 @@
 		reg = <0x13000000 0x100>;
 		interrupt-parent = <&pic>;
 		interrupts = <5>;
+		status = "disabled";
 	};
 
 	timer at 13000100 {
 		reg = <0x13000100 0x100>;
 		interrupt-parent = <&pic>;
 		interrupts = <6>;
+		status = "disabled";
 	};
 
 	timer at 13000200 {
 		reg = <0x13000200 0x100>;
 		interrupt-parent = <&pic>;
 		interrupts = <7>;
+		status = "disabled";
 	};
 
 	pic at 14000000 {
diff --git a/arch/arm/boot/dts/integratorap.dts b/arch/arm/boot/dts/integratorap.dts
index c9c3fa3..112d2e0 100644
--- a/arch/arm/boot/dts/integratorap.dts
+++ b/arch/arm/boot/dts/integratorap.dts
@@ -9,11 +9,6 @@
 	model = "ARM Integrator/AP";
 	compatible = "arm,integrator-ap";
 
-	aliases {
-		arm,timer-primary = &timer2;
-		arm,timer-secondary = &timer1;
-	};
-
 	chosen {
 		bootargs = "root=/dev/ram0 console=ttyAM0,38400n8 earlyprintk";
 	};
@@ -29,10 +24,14 @@
 
 	timer1: timer at 13000100 {
 		compatible = "arm,integrator-timer";
+		arm,sp804-clockevent = <0>;
+		status = "ok";
 	};
 
 	timer2: timer at 13000200 {
 		compatible = "arm,integrator-timer";
+		arm,sp804-clocksource = <0>;
+		status = "ok";
 	};
 
 	pic: pic at 14000000 {
diff --git a/arch/arm/boot/dts/integratorcp.dts b/arch/arm/boot/dts/integratorcp.dts
index 8b11939..19b2e3e 100644
--- a/arch/arm/boot/dts/integratorcp.dts
+++ b/arch/arm/boot/dts/integratorcp.dts
@@ -9,11 +9,6 @@
 	model = "ARM Integrator/CP";
 	compatible = "arm,integrator-cp";
 
-	aliases {
-		arm,timer-primary = &timer2;
-		arm,timer-secondary = &timer1;
-	};
-
 	chosen {
 		bootargs = "root=/dev/ram0 console=ttyAMA0,38400n8 earlyprintk";
 	};
@@ -29,10 +24,14 @@
 
 	timer1: timer at 13000100 {
 		compatible = "arm,sp804", "arm,primecell";
+		arm,sp804-clockevent = <0>;
+		status = "ok";
 	};
 
 	timer2: timer at 13000200 {
 		compatible = "arm,sp804", "arm,primecell";
+		arm,sp804-clocksource = <0>;
+		status = "ok";
 	};
 
 	pic: pic at 14000000 {
diff --git a/arch/arm/mach-integrator/Kconfig b/arch/arm/mach-integrator/Kconfig
index abeff25..031f43a 100644
--- a/arch/arm/mach-integrator/Kconfig
+++ b/arch/arm/mach-integrator/Kconfig
@@ -5,6 +5,7 @@ menu "Integrator Options"
 config ARCH_INTEGRATOR_AP
 	bool "Support Integrator/AP and Integrator/PP2 platforms"
 	select CLKSRC_MMIO
+	select CLKSRC_OF
 	select MIGHT_HAVE_PCI
 	select SERIAL_AMBA_PL010
 	select SERIAL_AMBA_PL010_CONSOLE
@@ -15,6 +16,8 @@ config ARCH_INTEGRATOR_AP
 
 config ARCH_INTEGRATOR_CP
 	bool "Support Integrator/CP platform"
+	select CLKSRC_MMIO
+	select CLKSRC_OF
 	select ARCH_CINTEGRATOR
 	select ARM_TIMER_SP804
 	select PLAT_VERSATILE_CLCD
diff --git a/arch/arm/mach-integrator/integrator_ap.c b/arch/arm/mach-integrator/integrator_ap.c
index c2112ff..2266944 100644
--- a/arch/arm/mach-integrator/integrator_ap.c
+++ b/arch/arm/mach-integrator/integrator_ap.c
@@ -425,45 +425,6 @@ void __init ap_init_early(void)
 
 #ifdef CONFIG_OF
 
-static void __init ap_of_timer_init(void)
-{
-	struct device_node *node;
-	const char *path;
-	void __iomem *base;
-	int err;
-	int irq;
-	struct clk *clk;
-	unsigned long rate;
-
-	clk = clk_get_sys("ap_timer", NULL);
-	BUG_ON(IS_ERR(clk));
-	clk_prepare_enable(clk);
-	rate = clk_get_rate(clk);
-
-	err = of_property_read_string(of_aliases,
-				"arm,timer-primary", &path);
-	if (WARN_ON(err))
-		return;
-	node = of_find_node_by_path(path);
-	base = of_iomap(node, 0);
-	if (WARN_ON(!base))
-		return;
-	writel(0, base + TIMER_CTRL);
-	integrator_clocksource_init(rate, base);
-
-	err = of_property_read_string(of_aliases,
-				"arm,timer-secondary", &path);
-	if (WARN_ON(err))
-		return;
-	node = of_find_node_by_path(path);
-	base = of_iomap(node, 0);
-	if (WARN_ON(!base))
-		return;
-	irq = irq_of_parse_and_map(node, 0);
-	writel(0, base + TIMER_CTRL);
-	integrator_clockevent_init(rate, base, irq);
-}
-
 static const struct of_device_id fpga_irq_of_match[] __initconst = {
 	{ .compatible = "arm,versatile-fpga-irq", .data = fpga_irq_of_init, },
 	{ /* Sentinel */ }
@@ -582,7 +543,7 @@ DT_MACHINE_START(INTEGRATOR_AP_DT, "ARM Integrator/AP (Device Tree)")
 	.init_early	= ap_init_early,
 	.init_irq	= ap_init_irq_of,
 	.handle_irq	= fpga_handle_irq,
-	.init_time	= ap_of_timer_init,
+	.init_time	= clocksource_of_init,
 	.init_machine	= ap_init_of,
 	.restart	= integrator_restart,
 	.dt_compat      = ap_dt_board_compat,
diff --git a/arch/arm/mach-integrator/integrator_cp.c b/arch/arm/mach-integrator/integrator_cp.c
index 40373ec..6e1c340 100644
--- a/arch/arm/mach-integrator/integrator_cp.c
+++ b/arch/arm/mach-integrator/integrator_cp.c
@@ -28,6 +28,7 @@
 #include <linux/of_address.h>
 #include <linux/of_platform.h>
 #include <linux/sys_soc.h>
+#include <linux/clocksource.h>
 #include <clocksource/arm_timer.h>
 #include <clocksource/timer-sp.h>
 
@@ -251,38 +252,6 @@ static void __init intcp_init_early(void)
 
 #ifdef CONFIG_OF
 
-static void __init cp_of_timer_init(void)
-{
-	struct device_node *node;
-	const char *path;
-	void __iomem *base;
-	int err;
-	int irq;
-
-	err = of_property_read_string(of_aliases,
-				"arm,timer-primary", &path);
-	if (WARN_ON(err))
-		return;
-	node = of_find_node_by_path(path);
-	base = of_iomap(node, 0);
-	if (WARN_ON(!base))
-		return;
-	writel(0, base + TIMER_CTRL);
-	sp804_clocksource_init(base, node->name);
-
-	err = of_property_read_string(of_aliases,
-				"arm,timer-secondary", &path);
-	if (WARN_ON(err))
-		return;
-	node = of_find_node_by_path(path);
-	base = of_iomap(node, 0);
-	if (WARN_ON(!base))
-		return;
-	irq = irq_of_parse_and_map(node, 0);
-	writel(0, base + TIMER_CTRL);
-	sp804_clockevents_init(base, irq, node->name);
-}
-
 static const struct of_device_id fpga_irq_of_match[] __initconst = {
 	{ .compatible = "arm,versatile-fpga-irq", .data = fpga_irq_of_init, },
 	{ /* Sentinel */ }
@@ -386,7 +355,7 @@ DT_MACHINE_START(INTEGRATOR_CP_DT, "ARM Integrator/CP (Device Tree)")
 	.init_early	= intcp_init_early,
 	.init_irq	= intcp_init_irq_of,
 	.handle_irq	= fpga_handle_irq,
-	.init_time	= cp_of_timer_init,
+	.init_time	= clocksource_of_init,
 	.init_machine	= intcp_init_of,
 	.restart	= integrator_restart,
 	.dt_compat      = intcp_dt_board_compat,
diff --git a/drivers/clocksource/timer-sp.c b/drivers/clocksource/timer-sp.c
index 63f757d..b3d9eba 100644
--- a/drivers/clocksource/timer-sp.c
+++ b/drivers/clocksource/timer-sp.c
@@ -201,6 +201,7 @@ static struct device_node *from = NULL;
 
 static struct of_device_id sp804_timer_match[] __initdata = {
 	{ .compatible = "arm,sp804", },
+	{ .compatible = "arm,integrator-timer", },
 	{}
 };
 
@@ -294,3 +295,4 @@ err:
 	iounmap(base);
 }
 CLOCKSOURCE_OF_DECLARE(sp804, "arm,sp804", sp804_dt_init)
+CLOCKSOURCE_OF_DECLARE(integrator, "arm,integrator-timer", sp804_dt_init)
-- 
1.7.10.4

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 05/11] ARM: highbank: use clocksource_of_init for sp804
  2013-03-13  5:05 [PATCH v3 00/11] add hisilicon SoC support Haojian Zhuang
                   ` (3 preceding siblings ...)
  2013-03-13  5:05 ` [PATCH v3 04/11] ARM: integrator: use clocksource_of_init for sp804 Haojian Zhuang
@ 2013-03-13  5:05 ` Haojian Zhuang
  2013-03-13  5:05 ` [PATCH v3 06/11] ARM: vexpress: " Haojian Zhuang
                   ` (5 subsequent siblings)
  10 siblings, 0 replies; 44+ messages in thread
From: Haojian Zhuang @ 2013-03-13  5:05 UTC (permalink / raw)
  To: linux-arm-kernel

Since sp804 hardware information could be stored in DTS file, remove
those ioremap operations. Use clocksource_of_init() instead.

Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
---
 arch/arm/boot/dts/ecx-common.dtsi |    4 +++-
 arch/arm/mach-highbank/highbank.c |   19 +------------------
 2 files changed, 4 insertions(+), 19 deletions(-)

diff --git a/arch/arm/boot/dts/ecx-common.dtsi b/arch/arm/boot/dts/ecx-common.dtsi
index d61b535..7ae5b2d 100644
--- a/arch/arm/boot/dts/ecx-common.dtsi
+++ b/arch/arm/boot/dts/ecx-common.dtsi
@@ -105,8 +105,10 @@
 			compatible = "arm,sp804", "arm,primecell";
 			reg = <0xfff34000 0x1000>;
 			interrupts = <0 18 4>;
-			clocks = <&pclk>;
+			clocks = <&pclk &pclk>;
 			clock-names = "apb_pclk";
+			arm,sp804-clocksource = <0x20>;
+			arm,sp804-clockevent = <0>;
 		};
 
 		rtc at fff35000 {
diff --git a/arch/arm/mach-highbank/highbank.c b/arch/arm/mach-highbank/highbank.c
index cfd843b..7829c2d 100644
--- a/arch/arm/mach-highbank/highbank.c
+++ b/arch/arm/mach-highbank/highbank.c
@@ -91,33 +91,16 @@ static void __init highbank_init_irq(void)
 #endif
 }
 
-static struct clk_lookup lookup = {
-	.dev_id = "sp804",
-	.con_id = NULL,
-};
-
 static void __init highbank_timer_init(void)
 {
-	int irq;
 	struct device_node *np;
-	void __iomem *timer_base;
 
 	/* Map system registers */
 	np = of_find_compatible_node(NULL, NULL, "calxeda,hb-sregs");
 	sregs_base = of_iomap(np, 0);
 	WARN_ON(!sregs_base);
 
-	np = of_find_compatible_node(NULL, NULL, "arm,sp804");
-	timer_base = of_iomap(np, 0);
-	WARN_ON(!timer_base);
-	irq = irq_of_parse_and_map(np, 0);
-
-	of_clk_init(NULL);
-	lookup.clk = of_clk_get(np, 0);
-	clkdev_add(&lookup);
-
-	sp804_clocksource_and_sched_clock_init(timer_base + 0x20, "timer1");
-	sp804_clockevents_init(timer_base, irq, "timer0");
+	clocksource_of_init();
 
 	twd_local_timer_of_register();
 
-- 
1.7.10.4

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 06/11] ARM: vexpress: use clocksource_of_init for sp804
  2013-03-13  5:05 [PATCH v3 00/11] add hisilicon SoC support Haojian Zhuang
                   ` (4 preceding siblings ...)
  2013-03-13  5:05 ` [PATCH v3 05/11] ARM: highbank: " Haojian Zhuang
@ 2013-03-13  5:05 ` Haojian Zhuang
  2013-03-13 11:10   ` Pawel Moll
  2013-03-13  5:05 ` [PATCH v3 07/11] ARM: debug: support debug ll on hisilicon soc Haojian Zhuang
                   ` (4 subsequent siblings)
  10 siblings, 1 reply; 44+ messages in thread
From: Haojian Zhuang @ 2013-03-13  5:05 UTC (permalink / raw)
  To: linux-arm-kernel

Remove all code to parse sp804. Use clocksource_of_init() instead since
all these code are implemented in sp804 driver already.

Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
---
 arch/arm/boot/dts/vexpress-v2m-rs1.dtsi |    2 ++
 arch/arm/boot/dts/vexpress-v2m.dtsi     |    2 ++
 arch/arm/boot/dts/vexpress-v2p-ca9.dts  |    2 ++
 arch/arm/mach-vexpress/Kconfig          |    1 +
 arch/arm/mach-vexpress/v2m.c            |   13 ++-----------
 5 files changed, 9 insertions(+), 11 deletions(-)

diff --git a/arch/arm/boot/dts/vexpress-v2m-rs1.dtsi b/arch/arm/boot/dts/vexpress-v2m-rs1.dtsi
index ac870fb..3fa798f 100644
--- a/arch/arm/boot/dts/vexpress-v2m-rs1.dtsi
+++ b/arch/arm/boot/dts/vexpress-v2m-rs1.dtsi
@@ -183,6 +183,8 @@
 				interrupts = <2>;
 				clocks = <&v2m_sysctl 0>, <&v2m_sysctl 1>, <&smbclk>;
 				clock-names = "timclken1", "timclken2", "apb_pclk";
+				arm,sp804-clocksource = <0x20>;
+				arm,sp804-clockevent = <0>;
 			};
 
 			v2m_timer23: timer at 120000 {
diff --git a/arch/arm/boot/dts/vexpress-v2m.dtsi b/arch/arm/boot/dts/vexpress-v2m.dtsi
index f142036..86e4046 100644
--- a/arch/arm/boot/dts/vexpress-v2m.dtsi
+++ b/arch/arm/boot/dts/vexpress-v2m.dtsi
@@ -182,6 +182,8 @@
 				interrupts = <2>;
 				clocks = <&v2m_sysctl 0>, <&v2m_sysctl 1>, <&smbclk>;
 				clock-names = "timclken1", "timclken2", "apb_pclk";
+				arm,sp804-clocksource = <0x20>;
+				arm,sp804-clockevent = <0>;
 			};
 
 			v2m_timer23: timer at 12000 {
diff --git a/arch/arm/boot/dts/vexpress-v2p-ca9.dts b/arch/arm/boot/dts/vexpress-v2p-ca9.dts
index 1420bb1..a2eba95 100644
--- a/arch/arm/boot/dts/vexpress-v2p-ca9.dts
+++ b/arch/arm/boot/dts/vexpress-v2p-ca9.dts
@@ -98,6 +98,8 @@
 			     <0 49 4>;
 		clocks = <&oscclk2>, <&oscclk2>;
 		clock-names = "timclk", "apb_pclk";
+		arm,sp804-clocksource = <0x20>;
+		arm,sp804-clockevent = <0>;
 	};
 
 	watchdog at 100e5000 {
diff --git a/arch/arm/mach-vexpress/Kconfig b/arch/arm/mach-vexpress/Kconfig
index 52d315b..ff78c15 100644
--- a/arch/arm/mach-vexpress/Kconfig
+++ b/arch/arm/mach-vexpress/Kconfig
@@ -5,6 +5,7 @@ config ARCH_VEXPRESS
 	select ARM_GIC
 	select ARM_TIMER_SP804
 	select CLKDEV_LOOKUP
+	select CLKSRC_OF
 	select COMMON_CLK
 	select COMMON_CLK_VERSATILE
 	select CPU_V7
diff --git a/arch/arm/mach-vexpress/v2m.c b/arch/arm/mach-vexpress/v2m.c
index 51e8701..bb599d3 100644
--- a/arch/arm/mach-vexpress/v2m.c
+++ b/arch/arm/mach-vexpress/v2m.c
@@ -21,6 +21,7 @@
 #include <linux/regulator/fixed.h>
 #include <linux/regulator/machine.h>
 #include <linux/vexpress.h>
+#include <linux/clocksource.h>
 #include <clocksource/arm_timer.h>
 #include <clocksource/timer-sp.h>
 
@@ -431,19 +432,9 @@ void __init v2m_dt_init_early(void)
 
 static void __init v2m_dt_timer_init(void)
 {
-	struct device_node *node = NULL;
-
 	vexpress_clk_of_init();
 
-	do {
-		node = of_find_compatible_node(node, NULL, "arm,sp804");
-	} while (node && vexpress_get_site_by_node(node) != VEXPRESS_SITE_MB);
-	if (node) {
-		pr_info("Using SP804 '%s' as a clock & events source\n",
-				node->full_name);
-		v2m_sp804_init(of_iomap(node, 0),
-				irq_of_parse_and_map(node, 0));
-	}
+	clocksource_of_init();
 
 	if (arch_timer_of_register() != 0)
 		twd_local_timer_of_register();
-- 
1.7.10.4

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 07/11] ARM: debug: support debug ll on hisilicon soc
  2013-03-13  5:05 [PATCH v3 00/11] add hisilicon SoC support Haojian Zhuang
                   ` (5 preceding siblings ...)
  2013-03-13  5:05 ` [PATCH v3 06/11] ARM: vexpress: " Haojian Zhuang
@ 2013-03-13  5:05 ` Haojian Zhuang
  2013-03-13  5:05 ` [PATCH v3 08/11] clk: hi3xxx: add clock support Haojian Zhuang
                   ` (3 subsequent siblings)
  10 siblings, 0 replies; 44+ messages in thread
From: Haojian Zhuang @ 2013-03-13  5:05 UTC (permalink / raw)
  To: linux-arm-kernel

Support UART0 debug ll on hisilicon Hi3620 SoC.

Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
---
 arch/arm/Kconfig.debug             |   15 +++++++++++++++
 arch/arm/include/debug/hisilicon.S |   30 ++++++++++++++++++++++++++++++
 2 files changed, 45 insertions(+)
 create mode 100644 arch/arm/include/debug/hisilicon.S

diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
index ecfcdba..fd2a39d 100644
--- a/arch/arm/Kconfig.debug
+++ b/arch/arm/Kconfig.debug
@@ -240,6 +240,20 @@ choice
 		  Say Y here if you want kernel low-level debugging support
 		  on i.MX6Q.
 
+	config DEBUG_HI3620_UART
+		bool "Hisilicon HI3620 Debug UART"
+		depends on ARCH_HI3xxx
+		help
+		  Say Y here if you want kernel low-level debugging support
+		  on HI3620 UART.
+
+	config DEBUG_HI3716_UART
+		bool "Hisilicon Hi3716 Debug UART"
+		depends on ARCH_HI3xxx
+		help
+		  Say Y here if you want kernel low-level debugging support
+		  on HI3716 UART.
+
 	config DEBUG_MMP_UART2
 		bool "Kernel low-level debugging message via MMP UART2"
 		depends on ARCH_MMP
@@ -589,6 +603,7 @@ config DEBUG_LL_INCLUDE
 				 DEBUG_IMX53_UART ||\
 				 DEBUG_IMX6Q_UART
 	default "debug/highbank.S" if DEBUG_HIGHBANK_UART
+	default "debug/hisilicon.S" if DEBUG_HI3620_UART || DEBUG_HI3716_UART
 	default "debug/mvebu.S" if DEBUG_MVEBU_UART
 	default "debug/omap2plus.S" if DEBUG_OMAP2PLUS_UART
 	default "debug/picoxcell.S" if DEBUG_PICOXCELL_UART
diff --git a/arch/arm/include/debug/hisilicon.S b/arch/arm/include/debug/hisilicon.S
new file mode 100644
index 0000000..47ad019
--- /dev/null
+++ b/arch/arm/include/debug/hisilicon.S
@@ -0,0 +1,30 @@
+/*
+ * Early serial output macro for Hisilicon SoC
+ *
+ * Copyright (C) 2012-2013 Hisilicon Technologies Co., Ltd.
+ * Copyright (C) 2012-2013 Linaro Ltd.
+ *
+ * Author: Haojian Zhuang <haojian.zhuang@linaro.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#if defined(CONFIG_DEBUG_HI3620_UART)
+#define HS_UART_PHYS_BASE	0xfcb00000
+#define HS_UART_VIRT_BASE	0xfeb00000
+#elif defined(CONFIG_DEBUG_HI3716_UART)
+#define HS_UART_PHYS_BASE	0xf8b00000
+#define HS_UART_VIRT_BASE	0xfeb00000
+#endif
+
+#if defined(CONFIG_DEBUG_HI3620_UART) || defined(CONFIG_DEBUG_HI3716_UART)
+		.macro	addruart,rp,rv,tmp
+		ldr	\rp, =HS_UART_PHYS_BASE
+		ldr	\rv, =HS_UART_VIRT_BASE
+		.endm
+
+#include <asm/hardware/debug-pl01x.S>
+
+#endif
-- 
1.7.10.4

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 08/11] clk: hi3xxx: add clock support
  2013-03-13  5:05 [PATCH v3 00/11] add hisilicon SoC support Haojian Zhuang
                   ` (6 preceding siblings ...)
  2013-03-13  5:05 ` [PATCH v3 07/11] ARM: debug: support debug ll on hisilicon soc Haojian Zhuang
@ 2013-03-13  5:05 ` Haojian Zhuang
  2013-03-13  5:05 ` [PATCH v3 09/11] ARM: hi3xxx: add board support with device tree Haojian Zhuang
                   ` (2 subsequent siblings)
  10 siblings, 0 replies; 44+ messages in thread
From: Haojian Zhuang @ 2013-03-13  5:05 UTC (permalink / raw)
  To: linux-arm-kernel

Add clock support with device tree on Hisilicon SoC.

Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
---
 .../devicetree/bindings/clock/hisilicon.txt        |   73 +++
 drivers/clk/Makefile                               |    1 +
 drivers/clk/clk-hi3xxx.c                           |  643 ++++++++++++++++++++
 3 files changed, 717 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/clock/hisilicon.txt
 create mode 100644 drivers/clk/clk-hi3xxx.c

diff --git a/Documentation/devicetree/bindings/clock/hisilicon.txt b/Documentation/devicetree/bindings/clock/hisilicon.txt
new file mode 100644
index 0000000..be8db9d
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/hisilicon.txt
@@ -0,0 +1,73 @@
+Device Tree Clock bindings for arch-vt8500
+
+This binding uses the common clock binding[1].
+
+[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+Required properties for mux clocks:
+ - compatible : Shall be "hisilicon,hi3620-clk-mux".
+ - clocks : shall be the input parent clock phandle for the clock. This should
+	be the reference clock.
+ - clock-output-names : shall be reference name.
+ - #clock-cells : from common clock binding; shall be set to 0.
+ - hisilicon,hi3620-mux : array of mux register offset & mask bits
+
+Required properties for Hi3620 gate clocks:
+ - compatible : Shall be "hisilicon,hi3620-clk-gate".
+ - clocks : shall be the input parent clock phandle for the clock. This should
+	be the reference clock.
+ - clock-output-names : shall be reference name.
+ - #clock-cells : from common clock binding; shall be set to 0.
+ - hisilicon,hi3620-clkgate : array of enable register offset & enable bits
+ - hisilicon,hi3620-clkreset : array of reset register offset & enable bits
+
+Required properties for clock divider:
+ - compatible : Shall be "hisilicon,hi3620-clk-div".
+ - clocks : shall be the input parent clock phandle for the clock. This should
+	be the reference clock.
+ - clock-output-names : shall be reference name.
+ - #clock-cells : from common clock binding; shall be set to 0.
+ - #hisilicon,clkdiv-table-cells : the number of parameters after phandle in
+   hisilicon,clkdiv-table property.
+ - hisilicon,clkdiv-table : list of value that are used to configure clock
+   divider. They're value of phandle, index & divider value.
+ - hisilicon,clkdiv : array of divider register offset & mask bits.
+
+Required properties for gate clocks:
+ - compatible : Shall be "hisilicon,clk-gate".
+ - clocks : shall be the input parent clock phandle for the clock. This should
+	be the reference clock.
+ - clock-output-names : shall be reference name.
+ - #clock-cells : from common clock binding; shall be set to 0.
+ - hisilicon,clkgate-inverted : bool value. True means that set-to-disable.
+
+Required properties for clock fixed factor divider:
+ - compatible : Shall be "hisilicon,fixed-factor".
+ - clocks : shall be the input parent clock phandle for the clock. This should
+	be the reference clock.
+ - clock-output-names : shall be reference name.
+ - #clock-cells : from common clock binding; shall be set to 0.
+ - hisilicon,fixed-factor : array of multiplier & divider.
+
+For example:
+	timclk1: clkgate at 38 {
+		compatible = "hisilicon,clk-gate";
+		#clock-cells = <0>;
+		clocks = <&refclk_timer1>;
+		clock-output-names = "timclk1";
+		hisilicon,clkgate-inverted;
+		hisilicon,clkgate = <0 18>;
+	};
+
+	dtable: clkdiv at 0 {
+		#hisilicon,clkdiv-table-cells = <2>;
+	};
+
+	div_cfgaxi: clkdiv at 2 {
+		compatible = "hisilicon,hi3620-clk-div";
+		#clock-cells = <0>;
+		clocks = <&div_shareaxi>;
+		clock-output-names = "cfgAXI_div";
+		hisilicon,clkdiv-table = <&dtable 0x01 2>;
+		hisilicon,clkdiv = <0x100 0x60>;
+	};
diff --git a/drivers/clk/Makefile b/drivers/clk/Makefile
index 0147022..b065e76 100644
--- a/drivers/clk/Makefile
+++ b/drivers/clk/Makefile
@@ -11,6 +11,7 @@ obj-$(CONFIG_COMMON_CLK)	+= clk-mux.o
 # SoCs specific
 obj-$(CONFIG_ARCH_BCM2835)	+= clk-bcm2835.o
 obj-$(CONFIG_ARCH_NOMADIK)	+= clk-nomadik.o
+obj-$(CONFIG_ARCH_HI3xxx)	+= clk-hi3xxx.o
 obj-$(CONFIG_ARCH_HIGHBANK)	+= clk-highbank.o
 obj-$(CONFIG_ARCH_MXS)		+= mxs/
 obj-$(CONFIG_ARCH_SOCFPGA)	+= socfpga/
diff --git a/drivers/clk/clk-hi3xxx.c b/drivers/clk/clk-hi3xxx.c
new file mode 100644
index 0000000..4499e57
--- /dev/null
+++ b/drivers/clk/clk-hi3xxx.c
@@ -0,0 +1,643 @@
+/*
+ * Hisilicon clock driver
+ *
+ * Copyright (c) 2012-2013 Hisilicon Limited.
+ * Copyright (c) 2012-2013 Linaro Limited.
+ *
+ * Author: Haojian Zhuang <haojian.zhuang@linaro.org>
+ *	   Xin Li <li.xin@linaro.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/clk-provider.h>
+#include <linux/clk-private.h>
+#include <linux/clkdev.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/slab.h>
+#include <linux/clk.h>
+
+#define HI3620_DISABLE_OFF		0x4
+#define HI3620_STATUS_OFF		0x8
+
+#define WIDTH_TO_MASK(width)	((1 << (width)) - 1)
+
+/*
+ * The reverse of DIV_ROUND_UP: The maximum number which
+ * divided by m is r
+ */
+#define MULT_ROUND_UP(r, m) ((r) * (m) + (m) - 1)
+
+struct hi3620_periclk {
+	struct clk_hw	hw;
+	void __iomem	*enable;	/* enable register */
+	void __iomem	*reset;		/* reset register */
+	u32		ebits;		/* bits in enable/disable register */
+	u32		rbits;		/* bits in reset/unreset register */
+	spinlock_t	*lock;
+};
+
+struct hi3620_muxclk {
+	struct clk_hw	hw;
+	void __iomem	*reg;		/* mux register */
+	u8		shift;
+	u8		width;
+	u32		mbits;		/* mask bits in mux register */
+	spinlock_t	*lock;
+};
+
+struct hi3620_divclk {
+	struct clk_hw	hw;
+	void __iomem	*reg;		/* divider register */
+	u8		shift;
+	u8		width;
+	u32		mbits;		/* mask bits in divider register */
+	const struct clk_div_table	*table;
+	spinlock_t	*lock;
+};
+
+struct hs_clk {
+	void __iomem	*pmctrl;
+	void __iomem	*sctrl;
+	spinlock_t	lock;
+};
+
+static struct hs_clk hs_clk;
+
+static void __init hs_init_clocks(void);
+
+static int hi3620_clkgate_prepare(struct clk_hw *hw)
+{
+	struct hi3620_periclk *pclk;
+	unsigned long flags = 0;
+
+	pclk = container_of(hw, struct hi3620_periclk, hw);
+
+	if (pclk->lock)
+		spin_lock_irqsave(pclk->lock, flags);
+	writel_relaxed(pclk->ebits, pclk->enable + HI3620_DISABLE_OFF);
+	writel_relaxed(pclk->rbits, pclk->reset + HI3620_DISABLE_OFF);
+	readl_relaxed(pclk->reset + HI3620_STATUS_OFF);
+	if (pclk->lock)
+		spin_unlock_irqrestore(pclk->lock, flags);
+	return 0;
+}
+
+static int hi3620_clkgate_enable(struct clk_hw *hw)
+{
+	struct hi3620_periclk *pclk;
+	unsigned long flags = 0;
+
+	pclk = container_of(hw, struct hi3620_periclk, hw);
+	if (pclk->lock)
+		spin_lock_irqsave(pclk->lock, flags);
+	writel_relaxed(pclk->ebits, pclk->enable);
+	readl_relaxed(pclk->enable + HI3620_STATUS_OFF);
+	if (pclk->lock)
+		spin_unlock_irqrestore(pclk->lock, flags);
+	return 0;
+}
+
+static void hi3620_clkgate_disable(struct clk_hw *hw)
+{
+	struct hi3620_periclk *pclk;
+	unsigned long flags = 0;
+
+	pclk = container_of(hw, struct hi3620_periclk, hw);
+	if (pclk->lock)
+		spin_lock_irqsave(pclk->lock, flags);
+	writel_relaxed(pclk->ebits, pclk->enable + HI3620_DISABLE_OFF);
+	readl_relaxed(pclk->enable + HI3620_STATUS_OFF);
+	if (pclk->lock)
+		spin_unlock_irqrestore(pclk->lock, flags);
+}
+
+static struct clk_ops hi3620_clkgate_ops = {
+	.prepare	= hi3620_clkgate_prepare,
+	.enable		= hi3620_clkgate_enable,
+	.disable	= hi3620_clkgate_disable,
+};
+
+static void __init hi3620_clkgate_setup(struct device_node *np)
+{
+	struct hi3620_periclk *pclk;
+	struct clk_init_data *init;
+	struct clk *clk;
+	const char *clk_name, *name, **parent_names;
+	u32 rdata[2], gdata[2];
+
+	if (!hs_clk.sctrl)
+		return;
+
+	if (of_property_read_string(np, "clock-output-names", &clk_name))
+		return;
+	if (of_property_read_u32_array(np, "hisilicon,hi3620-clkreset",
+				       &rdata[0], 2))
+		return;
+	if (of_property_read_u32_array(np, "hisilicon,hi3620-clkgate",
+				       &gdata[0], 2))
+		return;
+
+	/* gate only has the fixed parent */
+	parent_names = kzalloc(sizeof(char *), GFP_KERNEL);
+	if (!parent_names)
+		return;
+	parent_names[0] = of_clk_get_parent_name(np, 0);
+
+	pclk = kzalloc(sizeof(*pclk), GFP_KERNEL);
+	if (!pclk)
+		goto err_pclk;
+
+	init = kzalloc(sizeof(*init), GFP_KERNEL);
+	if (!init)
+		goto err_init;
+	init->name = kstrdup(clk_name, GFP_KERNEL);
+	init->ops = &hi3620_clkgate_ops;
+	init->flags = CLK_SET_RATE_PARENT;
+	init->parent_names = parent_names;
+	init->num_parents = 1;
+
+	pclk->reset = hs_clk.sctrl + rdata[0];
+	pclk->rbits = rdata[1];
+	pclk->enable = hs_clk.sctrl + gdata[0];
+	pclk->ebits = gdata[1];
+	pclk->lock = &hs_clk.lock;
+	pclk->hw.init = init;
+
+	clk = clk_register(NULL, &pclk->hw);
+	if (IS_ERR(clk))
+		goto err_clk;
+	if (!of_property_read_string(np, "clock-names", &name))
+		clk_register_clkdev(clk, name, NULL);
+	of_clk_add_provider(np, of_clk_src_simple_get, clk);
+	return;
+err_clk:
+	kfree(init);
+err_init:
+	kfree(pclk);
+err_pclk:
+	kfree(parent_names);
+}
+
+static u8 hi3620_clk_get_parent(struct clk_hw *hw)
+{
+	struct hi3620_muxclk *mclk;
+	u32 data;
+	unsigned long flags = 0;
+
+	mclk = container_of(hw, struct hi3620_muxclk, hw);
+
+	if (mclk->lock)
+		spin_lock_irqsave(mclk->lock, flags);
+
+	data = readl_relaxed(mclk->reg) >> mclk->shift;
+	data &= WIDTH_TO_MASK(mclk->width);
+
+	if (mclk->lock)
+		spin_unlock_irqrestore(mclk->lock, flags);
+
+	if (data >= __clk_get_num_parents(hw->clk))
+		return -EINVAL;
+
+	return (u8)data;
+}
+
+static int hi3620_clk_set_parent(struct clk_hw *hw, u8 index)
+{
+	struct hi3620_muxclk *mclk;
+	u32 data;
+	unsigned long flags = 0;
+
+	mclk = container_of(hw, struct hi3620_muxclk, hw);
+
+	if (mclk->lock)
+		spin_lock_irqsave(mclk->lock, flags);
+
+	data = readl_relaxed(mclk->reg);
+	data &= ~(WIDTH_TO_MASK(mclk->width) << mclk->shift);
+	data |= index << mclk->shift;
+	writel_relaxed(data, mclk->reg);
+	/* set mask enable bits */
+	data |= mclk->mbits;
+	writel_relaxed(data, mclk->reg);
+
+	if (mclk->lock)
+		spin_unlock_irqrestore(mclk->lock, flags);
+
+	return 0;
+}
+
+static struct clk_ops hi3620_clkmux_ops = {
+	.get_parent	= hi3620_clk_get_parent,
+	.set_parent	= hi3620_clk_set_parent,
+};
+
+static void __init hi3620_clkmux_setup(struct device_node *np)
+{
+	struct hi3620_muxclk *mclk;
+	struct clk_init_data *init;
+	struct clk *clk;
+	const char *clk_name, **parent_names;
+	u32 rdata[2];
+	u8 num_parents;
+	int i;
+
+	hs_init_clocks();
+	if (!hs_clk.sctrl)
+		return;
+
+	if (of_property_read_string(np, "clock-output-names", &clk_name))
+		return;
+	if (of_property_read_u32_array(np, "hisilicon,hi3620-clkmux",
+				       &rdata[0], 2))
+		return;
+	/* get the count of items in mux */
+	for (i = 0; ; i++) {
+		/* parent's #clock-cells property is always 0 */
+		if (!of_parse_phandle(np, "clocks", i))
+			break;
+	}
+	parent_names = kzalloc(sizeof(char *) * i, GFP_KERNEL);
+	if (!parent_names)
+		return;
+
+	for (num_parents = i, i = 0; i < num_parents; i++)
+		parent_names[i] = of_clk_get_parent_name(np, i);
+
+	mclk = kzalloc(sizeof(*mclk), GFP_KERNEL);
+	if (!mclk)
+		goto err_mclk;
+	init = kzalloc(sizeof(*init), GFP_KERNEL);
+	if (!init)
+		goto err_init;
+	init->name = kstrdup(clk_name, GFP_KERNEL);
+	init->ops = &hi3620_clkmux_ops;
+	init->flags = CLK_SET_RATE_PARENT;
+	init->parent_names = parent_names;
+	init->num_parents = num_parents;
+
+	mclk->reg = hs_clk.sctrl + rdata[0];
+	/* enable_mask bits are in higher 16bits */
+	mclk->mbits = rdata[1] << 16;
+	mclk->shift = ffs(rdata[1]) - 1;
+	mclk->width = fls(rdata[1]) - ffs(rdata[1]) + 1;
+	mclk->lock = &hs_clk.lock;
+	mclk->hw.init = init;
+
+	clk = clk_register(NULL, &mclk->hw);
+	if (IS_ERR(clk))
+		goto err_clk;
+	of_clk_add_provider(np, of_clk_src_simple_get, clk);
+
+	return;
+err_clk:
+	kfree(init);
+err_init:
+	kfree(mclk);
+err_mclk:
+	kfree(parent_names);
+}
+
+static void __init hs_clkgate_setup(struct device_node *np)
+{
+	struct clk *clk;
+	const char *clk_name, **parent_names, *name;
+	unsigned long flags = 0;
+	u32 data[2];
+
+	hs_init_clocks();
+	if (!hs_clk.sctrl)
+		return;
+	if (of_property_read_string(np, "clock-output-names", &clk_name))
+		return;
+	if (of_property_read_u32_array(np, "hisilicon,clkgate",
+				       &data[0], 2))
+		return;
+	if (of_property_read_bool(np, "hisilicon,clkgate-inverted"))
+		flags = CLK_GATE_SET_TO_DISABLE;
+	/* gate only has the fixed parent */
+	parent_names = kzalloc(sizeof(char *), GFP_KERNEL);
+	if (!parent_names)
+		return;
+	parent_names[0] = of_clk_get_parent_name(np, 0);
+
+	clk = clk_register_gate(NULL, clk_name, parent_names[0], 0,
+				hs_clk.sctrl + data[0], (u8)data[1], flags,
+				&hs_clk.lock);
+	if (IS_ERR(clk))
+		goto err;
+	if (!of_property_read_string(np, "clock-names", &name))
+		clk_register_clkdev(clk, name, NULL);
+	of_clk_add_provider(np, of_clk_src_simple_get, clk);
+	return;
+err:
+	kfree(parent_names);
+}
+
+void __init hs_fixed_factor_setup(struct device_node *np)
+{
+	struct clk *clk;
+	const char *clk_name, **parent_names;
+	u32 data[2];
+
+	if (of_property_read_string(np, "clock-output-names", &clk_name))
+		return;
+	if (of_property_read_u32_array(np, "hisilicon,fixed-factor",
+				       data, 2))
+		return ;
+	/* gate only has the fixed parent */
+	parent_names = kzalloc(sizeof(char *), GFP_KERNEL);
+	if (!parent_names)
+		return;
+	parent_names[0] = of_clk_get_parent_name(np, 0);
+
+	clk = clk_register_fixed_factor(NULL, clk_name, parent_names[0], 0,
+					data[0], data[1]);
+	if (IS_ERR(clk))
+		goto err;
+	of_clk_add_provider(np, of_clk_src_simple_get, clk);
+	return;
+err:
+	kfree(parent_names);
+}
+
+static unsigned int hi3620_get_table_maxdiv(const struct clk_div_table *table)
+{
+	unsigned int maxdiv = 0;
+	const struct clk_div_table *clkt;
+
+	for (clkt = table; clkt->div; clkt++)
+		if (clkt->div > maxdiv)
+			maxdiv = clkt->div;
+	return maxdiv;
+}
+
+static unsigned int hi3620_get_table_div(const struct clk_div_table *table,
+							unsigned int val)
+{
+	const struct clk_div_table *clkt;
+
+	for (clkt = table; clkt->div; clkt++)
+		if (clkt->val == val)
+			return clkt->div;
+	return 0;
+}
+
+static unsigned int hi3620_get_table_val(const struct clk_div_table *table,
+					 unsigned int div)
+{
+	const struct clk_div_table *clkt;
+
+	for (clkt = table; clkt->div; clkt++)
+		if (clkt->div == div)
+			return clkt->val;
+	return 0;
+}
+
+static unsigned long hi3620_clkdiv_recalc_rate(struct clk_hw *hw,
+					       unsigned long parent_rate)
+{
+	struct hi3620_divclk *dclk = container_of(hw, struct hi3620_divclk, hw);
+	unsigned int div, val;
+
+	val = readl_relaxed(dclk->reg) >> dclk->shift;
+	val &= WIDTH_TO_MASK(dclk->width);
+
+	div = hi3620_get_table_div(dclk->table, val);
+	if (!div) {
+		pr_warning("%s: Invalid divisor for clock %s\n", __func__,
+			   __clk_get_name(hw->clk));
+		return parent_rate;
+	}
+
+	return parent_rate / div;
+}
+
+static bool hi3620_is_valid_table_div(const struct clk_div_table *table,
+				      unsigned int div)
+{
+	const struct clk_div_table *clkt;
+
+	for (clkt = table; clkt->div; clkt++)
+		if (clkt->div == div)
+			return true;
+	return false;
+}
+
+static int hi3620_clkdiv_bestdiv(struct clk_hw *hw, unsigned long rate,
+				 unsigned long *best_parent_rate)
+{
+	struct hi3620_divclk *dclk = container_of(hw, struct hi3620_divclk, hw);
+	struct clk *clk_parent = __clk_get_parent(hw->clk);
+	int i, bestdiv = 0;
+	unsigned long parent_rate, best = 0, now, maxdiv;
+
+	maxdiv = hi3620_get_table_maxdiv(dclk->table);
+
+	if (!(__clk_get_flags(hw->clk) & CLK_SET_RATE_PARENT)) {
+		parent_rate = *best_parent_rate;
+		bestdiv = DIV_ROUND_UP(parent_rate, rate);
+		bestdiv = bestdiv == 0 ? 1 : bestdiv;
+		bestdiv = bestdiv > maxdiv ? maxdiv : bestdiv;
+		return bestdiv;
+	}
+
+	/*
+	 * The maximum divider we can use without overflowing
+	 * unsigned long in rate * i below
+	 */
+	maxdiv = min(ULONG_MAX / rate, maxdiv);
+
+	for (i = 1; i <= maxdiv; i++) {
+		if (!hi3620_is_valid_table_div(dclk->table, i))
+			continue;
+		parent_rate = __clk_round_rate(clk_parent,
+					       MULT_ROUND_UP(rate, i));
+		now = parent_rate / i;
+		if (now <= rate && now > best) {
+			bestdiv = i;
+			best = now;
+			*best_parent_rate = parent_rate;
+		}
+	}
+
+	if (!bestdiv) {
+		bestdiv = hi3620_get_table_maxdiv(dclk->table);
+		*best_parent_rate = __clk_round_rate(clk_parent, 1);
+	}
+
+	return bestdiv;
+}
+
+static long hi3620_clkdiv_round_rate(struct clk_hw *hw, unsigned long rate,
+				     unsigned long *prate)
+{
+	int div;
+
+	if (!rate)
+		rate = 1;
+	div = hi3620_clkdiv_bestdiv(hw, rate, prate);
+
+	return *prate / div;
+}
+
+static int hi3620_clkdiv_set_rate(struct clk_hw *hw, unsigned long rate,
+				  unsigned long parent_rate)
+{
+	struct hi3620_divclk *dclk = container_of(hw, struct hi3620_divclk, hw);
+	unsigned int div, value;
+	unsigned long flags = 0;
+	u32 data;
+
+	div = parent_rate / rate;
+	value = hi3620_get_table_val(dclk->table, div);
+
+	if (value > WIDTH_TO_MASK(dclk->width))
+		value = WIDTH_TO_MASK(dclk->width);
+
+	if (dclk->lock)
+		spin_lock_irqsave(dclk->lock, flags);
+
+	data = readl_relaxed(dclk->reg);
+	data &= ~(WIDTH_TO_MASK(dclk->width) << dclk->shift);
+	data |= value << dclk->shift;
+	data |= dclk->mbits;
+	writel_relaxed(data, dclk->reg);
+
+	if (dclk->lock)
+		spin_unlock_irqrestore(dclk->lock, flags);
+
+	return 0;
+}
+
+static struct clk_ops hi3620_clkdiv_ops = {
+	.recalc_rate = hi3620_clkdiv_recalc_rate,
+	.round_rate = hi3620_clkdiv_round_rate,
+	.set_rate = hi3620_clkdiv_set_rate,
+};
+
+void __init hi3620_clkdiv_setup(struct device_node *np)
+{
+	struct clk *clk;
+	const char *clk_name, **parent_names;
+	struct clk_init_data *init;
+	struct clk_div_table *table;
+	struct hi3620_divclk *dclk;
+	unsigned int table_num;
+	int i;
+	u32 data[2];
+	const char *propname = "hisilicon,clkdiv-table";
+	const char *cellname = "#hisilicon,clkdiv-table-cells";
+	struct of_phandle_args div_table;
+
+	hs_init_clocks();
+	if (!hs_clk.sctrl)
+		return;
+
+	if (of_property_read_string(np, "clock-output-names", &clk_name))
+		return;
+	if (of_property_read_u32_array(np, "hisilicon,clkdiv",
+				       &data[0], 2))
+		return;
+
+	/*process the div_table*/
+	for (i = 0; ; i++) {
+		if (of_parse_phandle_with_args(np, propname, cellname,
+					       i, &div_table))
+			break;
+	}
+
+	/*table ends with <0, 0>, so plus one to table_num*/
+	table_num = i + 1;
+
+	table = kzalloc(sizeof(struct clk_div_table) * table_num, GFP_KERNEL);
+	if (!table)
+		return ;
+
+	for (i = 0; ; i++) {
+		if (of_parse_phandle_with_args(np, propname, cellname,
+					       i, &div_table))
+			break;
+
+		table[i].val = div_table.args[0];
+		table[i].div = div_table.args[1];
+	}
+
+	/* gate only has the fixed parent */
+	parent_names = kzalloc(sizeof(char *), GFP_KERNEL);
+	if (!parent_names)
+		goto err_par;
+	parent_names[0] = of_clk_get_parent_name(np, 0);
+
+	dclk = kzalloc(sizeof(*dclk), GFP_KERNEL);
+	if (!dclk)
+		goto err_dclk;
+	init = kzalloc(sizeof(*init), GFP_KERNEL);
+	if (!init)
+		goto err_init;
+	init->name = kstrdup(clk_name, GFP_KERNEL);
+	init->ops = &hi3620_clkdiv_ops;
+	init->parent_names = parent_names;
+	init->num_parents = 1;
+
+	dclk->reg = hs_clk.sctrl + data[0];
+	dclk->shift = ffs(data[1]) - 1;
+	dclk->width = fls(data[1]) - ffs(data[1]) + 1;
+	dclk->mbits = data[1] << 16;
+	dclk->lock = &hs_clk.lock;
+	dclk->hw.init = init;
+	dclk->table = table;
+	clk = clk_register(NULL, &dclk->hw);
+	if (IS_ERR(clk))
+		goto err_clk;
+	of_clk_add_provider(np, of_clk_src_simple_get, clk);
+	return;
+err_clk:
+	kfree(init);
+err_init:
+	kfree(dclk);
+err_dclk:
+	kfree(parent_names);
+err_par:
+	kfree(table);
+}
+CLK_OF_DECLARE(hi3620_mux, "hisilicon,hi3620-clk-mux", hi3620_clkmux_setup)
+CLK_OF_DECLARE(hi3620_gate, "hisilicon,hi3620-clk-gate", hi3620_clkgate_setup)
+CLK_OF_DECLARE(hi3620_div, "hisilicon,hi3620-clk-div", hi3620_clkdiv_setup)
+CLK_OF_DECLARE(hs_gate, "hisilicon,clk-gate", hs_clkgate_setup)
+CLK_OF_DECLARE(hs_fixed, "hisilicon,clk-fixed-factor", hs_fixed_factor_setup)
+
+static void __init hs_init_clocks(void)
+{
+	struct device_node *node = NULL;
+
+	if (!hs_clk.pmctrl) {
+		/* map pmctrl registers */
+		node = of_find_compatible_node(NULL, NULL, "hisilicon,pmctrl");
+		hs_clk.pmctrl = of_iomap(node, 0);
+		WARN_ON(!hs_clk.pmctrl);
+	}
+
+	if (!hs_clk.sctrl) {
+		node = of_find_compatible_node(NULL, NULL, "hisilicon,sctrl");
+		hs_clk.sctrl = of_iomap(node, 0);
+	}
+}
-- 
1.7.10.4

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 09/11] ARM: hi3xxx: add board support with device tree
  2013-03-13  5:05 [PATCH v3 00/11] add hisilicon SoC support Haojian Zhuang
                   ` (7 preceding siblings ...)
  2013-03-13  5:05 ` [PATCH v3 08/11] clk: hi3xxx: add clock support Haojian Zhuang
@ 2013-03-13  5:05 ` Haojian Zhuang
  2013-03-13  5:05 ` [PATCH v3 10/11] ARM: hi3xxx: enable hi4511 " Haojian Zhuang
  2013-03-13  5:05 ` [PATCH v3 11/11] ARM: config: append arch hi3xxx into multi defconfig Haojian Zhuang
  10 siblings, 0 replies; 44+ messages in thread
From: Haojian Zhuang @ 2013-03-13  5:05 UTC (permalink / raw)
  To: linux-arm-kernel

Add board support with device tree for Hisilicon Hi36xx/Hi37xx platform.

Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
---
 .../bindings/arm/hisilicon/hisilicon.txt           |   10 +++++
 arch/arm/Kconfig                                   |    2 +
 arch/arm/Makefile                                  |    1 +
 arch/arm/mach-hi3xxx/Kconfig                       |   13 ++++++
 arch/arm/mach-hi3xxx/Makefile                      |    5 +++
 arch/arm/mach-hi3xxx/hi3xxx.c                      |   45 ++++++++++++++++++++
 6 files changed, 76 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt
 create mode 100644 arch/arm/mach-hi3xxx/Kconfig
 create mode 100644 arch/arm/mach-hi3xxx/Makefile
 create mode 100644 arch/arm/mach-hi3xxx/hi3xxx.c

diff --git a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt
new file mode 100644
index 0000000..3be60c8
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt
@@ -0,0 +1,10 @@
+Hisilicon Platforms Device Tree Bindings
+----------------------------------------------------
+
+Hi3716 Development Board
+Required root node properties:
+	- compatible = "hisilicon,hi3716-dkb";
+
+Hi4511 Board
+Required root node properties:
+	- compatible = "hisilicon,hi3620-hi4511";
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 10d7e2c..11ef3ea 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -1060,6 +1060,8 @@ source "arch/arm/mach-gemini/Kconfig"
 
 source "arch/arm/mach-h720x/Kconfig"
 
+source "arch/arm/mach-hi3xxx/Kconfig"
+
 source "arch/arm/mach-highbank/Kconfig"
 
 source "arch/arm/mach-integrator/Kconfig"
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index ee4605f..4b0de9e 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -148,6 +148,7 @@ machine-$(CONFIG_ARCH_EBSA110)		+= ebsa110
 machine-$(CONFIG_ARCH_EP93XX)		+= ep93xx
 machine-$(CONFIG_ARCH_GEMINI)		+= gemini
 machine-$(CONFIG_ARCH_H720X)		+= h720x
+machine-$(CONFIG_ARCH_HI3xxx)		+= hi3xxx
 machine-$(CONFIG_ARCH_HIGHBANK)		+= highbank
 machine-$(CONFIG_ARCH_INTEGRATOR)	+= integrator
 machine-$(CONFIG_ARCH_IOP13XX)		+= iop13xx
diff --git a/arch/arm/mach-hi3xxx/Kconfig b/arch/arm/mach-hi3xxx/Kconfig
new file mode 100644
index 0000000..a991dee
--- /dev/null
+++ b/arch/arm/mach-hi3xxx/Kconfig
@@ -0,0 +1,13 @@
+config ARCH_HI3xxx
+	bool "Hisilicon Hi36xx/Hi37xx family" if ARCH_MULTI_V7
+	select ARM_AMBA
+	select ARM_GIC
+	select CACHE_L2X0
+	select CACHE_PL310
+	select CLKSRC_OF
+	select PINCTRL
+	select PINCTRL_SINGLE
+	select SERIAL_AMBA_PL011
+	select SERIAL_AMBA_PL011_CONSOLE
+	help
+	  Support for Hisilicon Hi36xx/Hi37xx processor family
diff --git a/arch/arm/mach-hi3xxx/Makefile b/arch/arm/mach-hi3xxx/Makefile
new file mode 100644
index 0000000..d68ebb3
--- /dev/null
+++ b/arch/arm/mach-hi3xxx/Makefile
@@ -0,0 +1,5 @@
+#
+# Makefile for Hisilicon Hi36xx/Hi37xx processors line
+#
+
+obj-y	+= hi3xxx.o
diff --git a/arch/arm/mach-hi3xxx/hi3xxx.c b/arch/arm/mach-hi3xxx/hi3xxx.c
new file mode 100644
index 0000000..df0a472
--- /dev/null
+++ b/arch/arm/mach-hi3xxx/hi3xxx.c
@@ -0,0 +1,45 @@
+/*
+ * (Hisilicon's Hi36xx/Hi37xx SoC based) flattened device tree enabled machine
+ *
+ * Copyright (c) 2012-2013 Hisilicon Ltd.
+ * Copyright (c) 2012-2013 Linaro Ltd.
+ *
+ * Author: Haojian Zhuang <haojian.zhuang@linaro.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/clk-provider.h>
+#include <linux/clocksource.h>
+#include <linux/irqchip.h>
+#include <linux/of_platform.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+
+static void __init hi3xxx_timer_init(void)
+{
+	of_clk_init(NULL);
+	clocksource_of_init();
+}
+
+static void __init hs_init(void)
+{
+	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
+}
+
+static const char *hs_compat[] __initdata = {
+	"hisilicon,hi3620-hi4511",
+	NULL,
+};
+
+DT_MACHINE_START(HI3xxx, "Hisilicon Hi36xx/Hi37xx (Flattened Device Tree)")
+	/* Maintainer: Haojian Zhuang <haojian.zhuang@linaro.org> */
+	.map_io		= debug_ll_io_init,
+	.init_irq	= irqchip_init,
+	.init_time	= hi3xxx_timer_init,
+	.init_machine	= hs_init,
+	.dt_compat	= hs_compat,
+MACHINE_END
-- 
1.7.10.4

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 10/11] ARM: hi3xxx: enable hi4511 with device tree
  2013-03-13  5:05 [PATCH v3 00/11] add hisilicon SoC support Haojian Zhuang
                   ` (8 preceding siblings ...)
  2013-03-13  5:05 ` [PATCH v3 09/11] ARM: hi3xxx: add board support with device tree Haojian Zhuang
@ 2013-03-13  5:05 ` Haojian Zhuang
  2013-03-13  5:05 ` [PATCH v3 11/11] ARM: config: append arch hi3xxx into multi defconfig Haojian Zhuang
  10 siblings, 0 replies; 44+ messages in thread
From: Haojian Zhuang @ 2013-03-13  5:05 UTC (permalink / raw)
  To: linux-arm-kernel

Enable Hisilicon Hi4511 development platform with device tree support.

Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
---
 arch/arm/boot/dts/Makefile    |    1 +
 arch/arm/boot/dts/hi3620.dtsi | 1155 +++++++++++++++++++++++++++++++++++++++++
 arch/arm/boot/dts/hi4511.dts  |  743 ++++++++++++++++++++++++++
 3 files changed, 1899 insertions(+)
 create mode 100644 arch/arm/boot/dts/hi3620.dtsi
 create mode 100644 arch/arm/boot/dts/hi4511.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 1d14ebb..3c0410e 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -49,6 +49,7 @@ dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \
 	exynos5250-smdk5250.dtb \
 	exynos5250-snow.dtb \
 	exynos5440-ssdk5440.dtb
+dtb-$(CONFIG_ARCH_HI3xxx) += hi4511.dtb
 dtb-$(CONFIG_ARCH_HIGHBANK) += highbank.dtb \
 	ecx-2000.dtb
 dtb-$(CONFIG_ARCH_INTEGRATOR) += integratorap.dtb \
diff --git a/arch/arm/boot/dts/hi3620.dtsi b/arch/arm/boot/dts/hi3620.dtsi
new file mode 100644
index 0000000..e33fe7f
--- /dev/null
+++ b/arch/arm/boot/dts/hi3620.dtsi
@@ -0,0 +1,1155 @@
+/*
+ * Hisilicon Ltd. Hi3620 SoC
+ *
+ * Copyright (C) 2012-2013 Hisilicon Ltd.
+ * Copyright (C) 2012-2013 Linaro Ltd.
+ *
+ * Author: Haojian Zhuang <haojian.zhuang@linaro.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * publishhed by the Free Software Foundation.
+ */
+
+/include/ "skeleton.dtsi"
+
+/ {
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart1;
+		serial2 = &uart2;
+		serial3 = &uart3;
+		serial4 = &uart4;
+	};
+
+	osc32k: osc at 0 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "osc32khz";
+	};
+	osc26m: osc at 1 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <26000000>;
+		clock-output-names = "osc26mhz";
+	};
+	pclk: clk at 0 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <26000000>;
+		clock-output-names = "apb_pclk";
+	};
+	pll_arm0: clk at 1 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <1600000000>;
+		clock-output-names = "armpll0";
+	};
+	pll_arm1: clk at 2 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <1600000000>;
+		clock-output-names = "armpll1";
+	};
+	pll_peri: clk at 3 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <1440000000>;
+		clock-output-names = "armpll2";
+	};
+	pll_usb: clk at 4 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <1440000000>;
+		clock-output-names = "armpll3";
+	};
+	pll_hdmi: clk at 5 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <1188000000>;
+		clock-output-names = "armpll4";
+	};
+	pll_gpu: clk at 6 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <1300000000>;
+		clock-output-names = "armpll5";
+	};
+
+	amba {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "arm,amba-bus";
+		interrupt-parent = <&intc>;
+		ranges;
+
+		pmctrl: pmctrl at fca08000 {
+			compatible = "hisilicon,pmctrl";
+			reg = <0xfca08000 0x1000>;
+ 		};
+
+		sctrl: sctrl at fc802000 {
+			compatible = "hisilicon,sctrl";
+			reg = <0xfc802000 0x1000>;
+
+			refclk_uart0: refclk at 0 {
+				compatible = "hisilicon,hi3620-clk-mux";
+				#clock-cells = <0>;
+				clocks = <&osc26m &pclk>;
+				clock-output-names = "rclk_uart0";
+				/* each item value */
+				/* reg_offset, enable_bits */
+				hisilicon,hi3620-clkmux = <0x100 0x80>;
+			};
+			refclk_uart1: refclk at 1 {
+				compatible = "hisilicon,hi3620-clk-mux";
+				#clock-cells = <0>;
+				clocks = <&osc26m &pclk>;
+				clock-output-names = "rclk_uart1";
+				hisilicon,hi3620-clkmux = <0x100 0x100>;
+			};
+			refclk_uart2: refclk at 2 {
+				compatible = "hisilicon,hi3620-clk-mux";
+				#clock-cells = <0>;
+				clocks = <&osc26m &pclk>;
+				clock-output-names = "rclk_uart2";
+				hisilicon,hi3620-clkmux = <0x100 0x200>;
+			};
+			refclk_uart3: refclk at 3 {
+				compatible = "hisilicon,hi3620-clk-mux";
+				#clock-cells = <0>;
+				clocks = <&osc26m &pclk>;
+				clock-output-names = "rclk_uart3";
+				hisilicon,hi3620-clkmux = <0x100 0x400>;
+			};
+			refclk_uart4: refclk at 4 {
+				compatible = "hisilicon,hi3620-clk-mux";
+				#clock-cells = <0>;
+				clocks = <&osc26m &pclk>;
+				clock-output-names = "rclk_uart4";
+				hisilicon,hi3620-clkmux = <0x100 0x800>;
+			};
+			refclk_cfgaxi: refclk at 5 {
+				compatible = "hisilicon,clk-fixed-factor";
+				#clock-cells = <0>;
+				clocks = <&pll_peri>;
+				clock-output-names = "rclk_cfgaxi";
+				/*mult, div*/
+				hisilicon,fixed-factor = <1 30>;
+			};
+			refclk_spi0: refclk at 6 {
+				compatible = "hisilicon,hi3620-clk-mux";
+				#clock-cells = <0>;
+				clocks = <&osc26m &refclk_cfgaxi>;
+				clock-output-names = "rclk_spi0";
+				hisilicon,hi3620-clkmux = <0x100 0x1000>;
+			};
+			refclk_spi1: refclk at 7 {
+				compatible = "hisilicon,hi3620-clk-mux";
+				#clock-cells = <0>;
+				clocks = <&osc26m &refclk_cfgaxi>;
+				clock-output-names = "rclk_spi1";
+				hisilicon,hi3620-clkmux = <0x100 0x2000>;
+			};
+			refclk_spi2: refclk at 8 {
+				compatible = "hisilicon,hi3620-clk-mux";
+				#clock-cells = <0>;
+				clocks = <&osc26m &refclk_cfgaxi>;
+				clock-output-names = "rclk_spi2";
+				hisilicon,hi3620-clkmux = <0x100 0x4000>;
+			};
+			refclk_pwm0: refclk at 9 {
+				compatible = "hisilicon,hi3620-clk-mux";
+				#clock-cells = <0>;
+				clocks = <&osc32k &osc26m>;
+				clock-output-names = "rclk_pwm0";
+				hisilicon,hi3620-clkmux = <0x104 0x400>;
+			};
+			refclk_pwm1: refclk at 10 {
+				compatible = "hisilicon,hi3620-clk-mux";
+				#clock-cells = <0>;
+				clocks = <&osc32k &osc26m>;
+				clock-output-names = "rclk_pwm1";
+				hisilicon,hi3620-clkmux = <0x104 0x800>;
+			};
+			refclk_tcxo: refclk at 11 {
+				compatible = "hisilicon,clk-fixed-factor";
+				#clock-cells = <0>;
+				clocks = <&osc26m>;
+				clock-output-names = "rclk_tcxo";
+				hisilicon,fixed-factor = <1 4>;
+			};
+			refclk_timer0: refclk at 12 {
+				compatible = "hisilicon,hi3620-clk-mux";
+				#clock-cells = <0>;
+				clocks = <&osc32k &timerclk01>;
+				clock-output-names = "rclk_tim0";
+				hisilicon,hi3620-clkmux = <0 0x8000>;
+			};
+			refclk_timer1: refclk at 13 {
+				compatible = "hisilicon,hi3620-clk-mux";
+				#clock-cells = <0>;
+				clocks = <&osc32k &timerclk01>;
+				clock-output-names = "rclk_tim1";
+				hisilicon,hi3620-clkmux = <0 0x20000>;
+			};
+			refclk_timer2: refclk at 14 {
+				compatible = "hisilicon,hi3620-clk-mux";
+				#clock-cells = <0>;
+				clocks = <&osc32k &timerclk23>;
+				clock-output-names = "rclk_tim2";
+				hisilicon,hi3620-clkmux = <0 0x80000>;
+			};
+			refclk_timer3: refclk at 15 {
+				compatible = "hisilicon,hi3620-clk-mux";
+				#clock-cells = <0>;
+				clocks = <&osc32k &timerclk23>;
+				clock-output-names = "rclk_tim3";
+				hisilicon,hi3620-clkmux = <0 0x200000>;
+			};
+			refclk_timer4: refclk at 16 {
+				compatible = "hisilicon,hi3620-clk-mux";
+				#clock-cells = <0>;
+				clocks = <&osc32k &timerclk45>;
+				clock-output-names = "rclk_tim4";
+				hisilicon,hi3620-clkmux = <0x18 0x1>;
+			};
+			refclk_timer5: refclk at 17 {
+				compatible = "hisilicon,hi3620-clk-mux";
+				#clock-cells = <0>;
+				clocks = <&osc32k &timerclk45>;
+				clock-output-names = "rclk_tim5";
+				hisilicon,hi3620-clkmux = <0x18 0x4>;
+			};
+			refclk_timer6: refclk at 18 {
+				compatible = "hisilicon,hi3620-clk-mux";
+				#clock-cells = <0>;
+				clocks = <&osc32k &timerclk67>;
+				clock-output-names = "rclk_tim6";
+				hisilicon,hi3620-clkmux = <0x18 0x10>;
+			};
+			refclk_timer7: refclk at 19 {
+				compatible = "hisilicon,hi3620-clk-mux";
+				#clock-cells = <0>;
+				clocks = <&osc32k &timerclk67>;
+				clock-output-names = "rclk_tim7";
+				hisilicon,hi3620-clkmux = <0x18 0x40>;
+			};
+			refclk_timer8: refclk at 20 {
+				compatible = "hisilicon,hi3620-clk-mux";
+				#clock-cells = <0>;
+				clocks = <&osc32k &timerclk89>;
+				clock-output-names = "rclk_tim8";
+				hisilicon,hi3620-clkmux = <0x18 0x100>;
+			};
+			refclk_timer9: refclk at 21 {
+				compatible = "hisilicon,hi3620-clk-mux";
+				#clock-cells = <0>;
+				clocks = <&osc32k &timerclk89>;
+				clock-output-names = "rclk_tim9";
+				hisilicon,hi3620-clkmux = <0x18 0x400>;
+			};
+			refclk_shareAXI: refclk at 22 {
+				compatible = "hisilicon,hi3620-clk-mux";
+				#clock-cells = <0>;
+				clocks = <&pll_usb &pll_peri>;
+				clock-output-names = "rclk_shareAXI";
+				hisilicon,hi3620-clkmux = <0x24 0x8000>;
+			};
+			uartclk0: clkgate at 0 {
+				compatible = "hisilicon,hi3620-clk-gate";
+				#clock-cells = <0>;
+				clocks = <&refclk_uart0>;
+				clock-output-names = "uartclk0";
+				hisilicon,hi3620-clkreset = <0x98 0x10000>;
+				hisilicon,hi3620-clkgate = <0x40 0x10000>;
+			};
+			uartclk1: clkgate at 1 {
+				compatible = "hisilicon,hi3620-clk-gate";
+				#clock-cells = <0>;
+				clocks = <&refclk_uart1>;
+				clock-output-names = "uartclk1";
+				hisilicon,hi3620-clkreset = <0x98 0x20000>;
+				hisilicon,hi3620-clkgate = <0x40 0x20000>;
+			};
+			uartclk2: clkgate at 2 {
+				compatible = "hisilicon,hi3620-clk-gate";
+				#clock-cells = <0>;
+				clocks = <&refclk_uart2>;
+				clock-output-names = "uartclk2";
+				hisilicon,hi3620-clkreset = <0x98 0x40000>;
+				hisilicon,hi3620-clkgate = <0x40 0x40000>;
+			};
+			uartclk3: clkgate at 3 {
+				compatible = "hisilicon,hi3620-clk-gate";
+				#clock-cells = <0>;
+				clocks = <&refclk_uart3>;
+				clock-output-names = "uartclk3";
+				hisilicon,hi3620-clkreset = <0x98 0x80000>;
+				hisilicon,hi3620-clkgate = <0x40 0x80000>;
+			};
+			uartclk4: clkgate at 4 {
+				compatible = "hisilicon,hi3620-clk-gate";
+				#clock-cells = <0>;
+				clocks = <&refclk_uart4>;
+				clock-output-names = "uartclk4";
+				hisilicon,hi3620-clkreset = <0x98 0x100000>;
+				hisilicon,hi3620-clkgate = <0x40 0x100000>;
+			};
+			gpioclk0: clkgate at 5 {
+				compatible = "hisilicon,hi3620-clk-gate";
+				#clock-cells = <0>;
+				clocks = <&pclk>;
+				clock-output-names = "gpioclk0";
+				hisilicon,hi3620-clkreset = <0x80 0x100>;
+				hisilicon,hi3620-clkgate = <0x20 0x100>;
+			};
+			gpioclk1: clkgate at 6 {
+				compatible = "hisilicon,hi3620-clk-gate";
+				#clock-cells = <0>;
+				clocks = <&pclk>;
+				clock-output-names = "gpioclk1";
+				hisilicon,hi3620-clkreset = <0x80 0x200>;
+				hisilicon,hi3620-clkgate = <0x20 0x200>;
+			};
+			gpioclk2: clkgate at 7 {
+				compatible = "hisilicon,hi3620-clk-gate";
+				#clock-cells = <0>;
+				clocks = <&pclk>;
+				clock-output-names = "gpioclk2";
+				hisilicon,hi3620-clkreset = <0x80 0x400>;
+				hisilicon,hi3620-clkgate = <0x20 0x400>;
+			};
+			gpioclk3: clkgate at 8 {
+				compatible = "hisilicon,hi3620-clk-gate";
+				#clock-cells = <0>;
+				clocks = <&pclk>;
+				clock-output-names = "gpioclk3";
+				hisilicon,hi3620-clkreset = <0x80 0x800>;
+				hisilicon,hi3620-clkgate = <0x20 0x800>;
+			};
+			gpioclk4: clkgate at 9 {
+				compatible = "hisilicon,hi3620-clk-gate";
+				#clock-cells = <0>;
+				clocks = <&pclk>;
+				clock-output-names = "gpioclk4";
+				hisilicon,hi3620-clkreset = <0x80 0x1000>;
+				hisilicon,hi3620-clkgate = <0x20 0x1000>;
+			};
+			gpioclk5: clkgate at 10 {
+				compatible = "hisilicon,hi3620-clk-gate";
+				#clock-cells = <0>;
+				clocks = <&pclk>;
+				clock-output-names = "gpioclk5";
+				hisilicon,hi3620-clkreset = <0x80 0x2000>;
+				hisilicon,hi3620-clkgate = <0x20 0x2000>;
+			};
+			gpioclk6: clkgate at 11 {
+				compatible = "hisilicon,hi3620-clk-gate";
+				#clock-cells = <0>;
+				clocks = <&pclk>;
+				clock-output-names = "gpioclk6";
+				hisilicon,hi3620-clkreset = <0x80 0x4000>;
+				hisilicon,hi3620-clkgate = <0x20 0x4000>;
+			};
+			gpioclk7: clkgate at 12 {
+				compatible = "hisilicon,hi3620-clk-gate";
+				#clock-cells = <0>;
+				clocks = <&pclk>;
+				clock-output-names = "gpioclk7";
+				hisilicon,hi3620-clkreset = <0x80 0x8000>;
+				hisilicon,hi3620-clkgate = <0x20 0x8000>;
+			};
+			gpioclk8: clkgate at 13 {
+				compatible = "hisilicon,hi3620-clk-gate";
+				#clock-cells = <0>;
+				clocks = <&pclk>;
+				clock-output-names = "gpioclk8";
+				hisilicon,hi3620-clkreset = <0x80 0x10000>;
+				hisilicon,hi3620-clkgate = <0x20 0x10000>;
+			};
+			gpioclk9: clkgate at 14 {
+				compatible = "hisilicon,hi3620-clk-gate";
+				#clock-cells = <0>;
+				clocks = <&pclk>;
+				clock-output-names = "gpioclk9";
+				hisilicon,hi3620-clkreset = <0x80 0x20000>;
+				hisilicon,hi3620-clkgate = <0x20 0x20000>;
+			};
+			gpioclk10: clkgate at 15 {
+				compatible = "hisilicon,hi3620-clk-gate";
+				#clock-cells = <0>;
+				clocks = <&pclk>;
+				clock-output-names = "gpioclk10";
+				hisilicon,hi3620-clkreset = <0x80 0x40000>;
+				hisilicon,hi3620-clkgate = <0x20 0x40000>;
+			};
+			gpioclk11: clkgate at 16 {
+				compatible = "hisilicon,hi3620-clk-gate";
+				#clock-cells = <0>;
+				clocks = <&pclk>;
+				clock-output-names = "gpioclk11";
+				hisilicon,hi3620-clkreset = <0x80 0x80000>;
+				hisilicon,hi3620-clkgate = <0x20 0x80000>;
+			};
+			gpioclk12: clkgate at 17 {
+				compatible = "hisilicon,hi3620-clk-gate";
+				#clock-cells = <0>;
+				clocks = <&pclk>;
+				clock-output-names = "gpioclk12";
+				hisilicon,hi3620-clkreset = <0x80 0x100000>;
+				hisilicon,hi3620-clkgate = <0x20 0x100000>;
+			};
+			gpioclk13: clkgate at 18 {
+				compatible = "hisilicon,hi3620-clk-gate";
+				#clock-cells = <0>;
+				clocks = <&pclk>;
+				clock-output-names = "gpioclk13";
+				hisilicon,hi3620-clkreset = <0x80 0x200000>;
+				hisilicon,hi3620-clkgate = <0x20 0x200000>;
+			};
+			gpioclk14: clkgate at 19 {
+				compatible = "hisilicon,hi3620-clk-gate";
+				#clock-cells = <0>;
+				clocks = <&pclk>;
+				clock-output-names = "gpioclk14";
+				hisilicon,hi3620-clkreset = <0x80 0x400000>;
+				hisilicon,hi3620-clkgate = <0x20 0x400000>;
+			};
+			gpioclk15: clkgate at 20 {
+				compatible = "hisilicon,hi3620-clk-gate";
+				#clock-cells = <0>;
+				clocks = <&pclk>;
+				clock-output-names = "gpioclk15";
+				hisilicon,hi3620-clkreset = <0x80 0x800000>;
+				hisilicon,hi3620-clkgate = <0x20 0x800000>;
+			};
+			gpioclk16: clkgate at 21 {
+				compatible = "hisilicon,hi3620-clk-gate";
+				#clock-cells = <0>;
+				clocks = <&pclk>;
+				clock-output-names = "gpioclk16";
+				hisilicon,hi3620-clkreset = <0x80 0x1000000>;
+				hisilicon,hi3620-clkgate = <0x20 0x1000000>;
+			};
+			gpioclk17: clkgate at 22 {
+				compatible = "hisilicon,hi3620-clk-gate";
+				#clock-cells = <0>;
+				clocks = <&pclk>;
+				clock-output-names = "gpioclk17";
+				hisilicon,hi3620-clkreset = <0x80 0x2000000>;
+				hisilicon,hi3620-clkgate = <0x20 0x2000000>;
+			};
+			gpioclk18: clkgate at 23 {
+				compatible = "hisilicon,hi3620-clk-gate";
+				#clock-cells = <0>;
+				clocks = <&pclk>;
+				clock-output-names = "gpioclk18";
+				hisilicon,hi3620-clkreset = <0x80 0x4000000>;
+				hisilicon,hi3620-clkgate = <0x20 0x4000000>;
+			};
+			gpioclk19: clkgate at 24 {
+				compatible = "hisilicon,hi3620-clk-gate";
+				#clock-cells = <0>;
+				clocks = <&pclk>;
+				clock-output-names = "gpioclk19";
+				hisilicon,hi3620-clkreset = <0x80 0x8000000>;
+				hisilicon,hi3620-clkgate = <0x20 0x8000000>;
+			};
+			gpioclk20: clkgate at 25 {
+				compatible = "hisilicon,hi3620-clk-gate";
+				#clock-cells = <0>;
+				clocks = <&pclk>;
+				clock-output-names = "gpioclk20";
+				hisilicon,hi3620-clkreset = <0x80 0x10000000>;
+				hisilicon,hi3620-clkgate = <0x20 0x10000000>;
+			};
+			gpioclk21: clkgate at 26 {
+				compatible = "hisilicon,hi3620-clk-gate";
+				#clock-cells = <0>;
+				clocks = <&pclk>;
+				clock-output-names = "gpioclk21";
+				hisilicon,hi3620-clkreset = <0x80 0x20000000>;
+				hisilicon,hi3620-clkgate = <0x20 0x20000000>;
+			};
+			spiclk0: clkgate at 27 {
+				compatible = "hisilicon,hi3620-clk-gate";
+				#clock-cells = <0>;
+				clocks = <&refclk_spi0>;
+				clock-output-names = "spiclk0";
+				hisilicon,hi3620-clkreset = <0x98 0x200000>;
+				hisilicon,hi3620-clkgate = <0x40 0x200000>;
+			};
+			spiclk1: clkgate at 28 {
+				compatible = "hisilicon,hi3620-clk-gate";
+				#clock-cells = <0>;
+				clocks = <&refclk_spi1>;
+				clock-output-names = "spiclk1";
+				hisilicon,hi3620-clkreset = <0x98 0x400000>;
+				hisilicon,hi3620-clkgate = <0x40 0x400000>;
+			};
+			spiclk2: clkgate at 29 {
+				compatible = "hisilicon,hi3620-clk-gate";
+				#clock-cells = <0>;
+				clocks = <&refclk_spi2>;
+				clock-output-names = "spiclk2";
+				hisilicon,hi3620-clkreset = <0x98 0x800000>;
+				hisilicon,hi3620-clkgate = <0x40 0x800000>;
+			};
+			pwmclk0: clkgate at 30 {
+				compatible = "hisilicon,hi3620-clk-gate";
+				#clock-cells = <0>;
+				clocks = <&refclk_pwm0>;
+				clock-output-names = "pwmclk0";
+				hisilicon,hi3620-clkreset = <0x98 0x80>;
+				hisilicon,hi3620-clkgate = <0x40 0x80>;
+			};
+			pwmclk1: clkgate at 31 {
+				compatible = "hisilicon,hi3620-clk-gate";
+				#clock-cells = <0>;
+				clocks = <&refclk_pwm1>;
+				clock-output-names = "pwmclk1";
+				hisilicon,hi3620-clkreset = <0x98 0x100>;
+				hisilicon,hi3620-clkgate = <0x40 0x100>;
+			};
+			timerclk01: clkgate at 32 {
+				compatible = "hisilicon,hi3620-clk-gate";
+				#clock-cells = <0>;
+				clocks = <&refclk_tcxo>;
+				clock-output-names = "timerclk01";
+				hisilicon,hi3620-clkreset = <0x80 0x1>;
+				hisilicon,hi3620-clkgate = <0x20 0x3>;
+			};
+			timerclk23: clkgate at 33 {
+				compatible = "hisilicon,hi3620-clk-gate";
+				#clock-cells = <0>;
+				clocks = <&refclk_tcxo>;
+				clock-output-names = "timerclk23";
+				hisilicon,hi3620-clkreset = <0x80 0x2>;
+				hisilicon,hi3620-clkgate = <0x20 0xc>;
+			};
+			timerclk45: clkgate at 34 {
+				compatible = "hisilicon,hi3620-clk-gate";
+				#clock-cells = <0>;
+				clocks = <&refclk_tcxo>;
+				clock-output-names = "timerclk45";
+				hisilicon,hi3620-clkreset = <0x98 0x8>;
+				hisilicon,hi3620-clkgate = <0x40 0x8>;
+			};
+			timerclk67: clkgate at 35 {
+				compatible = "hisilicon,hi3620-clk-gate";
+				#clock-cells = <0>;
+				clocks = <&refclk_tcxo>;
+				clock-output-names = "timerclk67";
+				hisilicon,hi3620-clkreset = <0x98 0x10>;
+				hisilicon,hi3620-clkgate = <0x40 0x10>;
+			};
+			timerclk89: clkgate at 36 {
+				compatible = "hisilicon,hi3620-clk-gate";
+				#clock-cells = <0>;
+				clocks = <&refclk_tcxo>;
+				clock-output-names = "timerclk89";
+				hisilicon,hi3620-clkreset = <0x98 0x20>;
+				hisilicon,hi3620-clkgate = <0x40 0x20>;
+			};
+			timclk0: clkgate at 37 {
+				compatible = "hisilicon,clk-gate";
+				#clock-cells = <0>;
+				clocks = <&refclk_timer0>;
+				clock-output-names = "timclk0";
+				hisilicon,clkgate-inverted;
+				hisilicon,clkgate = <0 16>;
+			};
+			timclk1: clkgate at 38 {
+				compatible = "hisilicon,clk-gate";
+				#clock-cells = <0>;
+				clocks = <&refclk_timer1>;
+				clock-output-names = "timclk1";
+				hisilicon,clkgate-inverted;
+				hisilicon,clkgate = <0 18>;
+			};
+			timclk2: clkgate at 39 {
+				compatible = "hisilicon,clk-gate";
+				#clock-cells = <0>;
+				clocks = <&refclk_timer2>;
+				clock-output-names = "timclk2";
+				hisilicon,clkgate-inverted;
+				hisilicon,clkgate = <0 20>;
+			};
+			timclk3: clkgate at 40 {
+				compatible = "hisilicon,clk-gate";
+				#clock-cells = <0>;
+				clocks = <&refclk_timer3>;
+				clock-output-names = "timclk3";
+				hisilicon,clkgate-inverted;
+				hisilicon,clkgate = <0 22>;
+			};
+			timclk4: clkgate at 41 {
+				compatible = "hisilicon,clk-gate";
+				#clock-cells = <0>;
+				clocks = <&refclk_timer4>;
+				clock-output-names = "timclk4";
+				hisilicon,clkgate-inverted;
+				hisilicon,clkgate = <0x18 0>;
+			};
+			timclk5: clkgate at 42 {
+				compatible = "hisilicon,clk-gate";
+				#clock-cells = <0>;
+				clocks = <&refclk_timer5>;
+				clock-output-names = "timclk5";
+				hisilicon,clkgate-inverted;
+				hisilicon,clkgate = <0x18 2>;
+			};
+			timclk6: clkgate at 43 {
+				compatible = "hisilicon,clk-gate";
+				#clock-cells = <0>;
+				clocks = <&refclk_timer6>;
+				clock-output-names = "timclk6";
+				hisilicon,clkgate-inverted;
+				hisilicon,clkgate = <0x18 4>;
+			};
+			timclk7: clkgate at 44 {
+				compatible = "hisilicon,clk-gate";
+				#clock-cells = <0>;
+				clocks = <&refclk_timer7>;
+				clock-output-names = "timclk7";
+				hisilicon,clkgate-inverted;
+				hisilicon,clkgate = <0x18 6>;
+			};
+			timclk8: clkgate at 45 {
+				compatible = "hisilicon,clk-gate";
+				#clock-cells = <0>;
+				clocks = <&refclk_timer8>;
+				clock-output-names = "timclk8";
+				hisilicon,clkgate-inverted;
+				hisilicon,clkgate = <0x18 8>;
+			};
+			timclk9: clkgate at 46 {
+				compatible = "hisilicon,clk-gate";
+				#clock-cells = <0>;
+				clocks = <&refclk_timer9>;
+				clock-output-names = "timclk9";
+				hisilicon,clkgate-inverted;
+				hisilicon,clkgate = <0x18 10>;
+			};
+			dtable: clkdiv at 0 {
+				#hisilicon,clkdiv-table-cells = <2>;
+			};
+			div_shareaxi: clkdiv at 1 {
+				compatible = "hisilicon,hi3620-clk-div";
+				#clock-cells = <0>;
+				clocks = <&refclk_shareAXI>;
+				clock-output-names = "shareAXI_div";
+				hisilicon,clkdiv-table = <
+					&dtable 0 1 &dtable 1 2 &dtable 2 3 &dtable 3 4
+					&dtable 4 5 &dtable 5 6 &dtable 6 7 &dtable 7 8
+					&dtable 8 9 &dtable 9 10 &dtable 10 11 &dtable 11 12
+					&dtable 12 13 &dtable 13 14 &dtable 14 15 &dtable 15 16
+					&dtable 16 17 &dtable 17 18 &dtable 18 19 &dtable 19 20
+					&dtable 20 21 &dtable 21 22 &dtable 22 23 &dtable 23 24
+					&dtable 24 25 &dtable 25 26 &dtable 26 27 &dtable 27 28
+					&dtable 28 29 &dtable 29 30 &dtable 30 31 &dtable 31 32>;
+				/* divider register offset, mask */
+				hisilicon,clkdiv = <0x100 0x1f>;
+			};
+			div_cfgaxi: clkdiv at 2 {
+				compatible = "hisilicon,hi3620-clk-div";
+				#clock-cells = <0>;
+				clocks = <&div_shareaxi>;
+				clock-output-names = "cfgAXI_div";
+				hisilicon,clkdiv-table = <&dtable 0x01 2>;
+				hisilicon,clkdiv = <0x100 0x60>;
+			};
+ 		};
+
+		l2: l2-cache {
+			compatible = "arm,pl310-cache";
+			reg = <0xfc10000 0x100000>;
+			interrupts = <0 15 4>;
+			cache-unified;
+			cache-level = <2>;
+		};
+
+		intc: interrupt-controller at fc001000 {
+			compatible = "arm,cortex-a9-gic";
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+			interrupt-controller;
+			/* gic dist base, gic cpu base */
+			reg = <0xfc001000 0x1000>, <0xfc000100 0x100>;
+		};
+
+		timer0: timer at fc800000 {
+			compatible = "arm,sp804", "arm,primecell";
+			reg = <0xfc800000 0x1000>;
+			/* timer00 & timer01 */
+			interrupts = <0 0 4>, <0 1 4>;
+			clocks = <&timclk0 &timclk1>;
+			clock-names = "apb_pclk";
+			status = "disabled";
+		};
+
+		timer1: timer at fc801000 {
+			compatible = "arm,sp804", "arm,primecell";
+			reg = <0xfc801000 0x1000>;
+			/* timer10 & timer11 */
+			interrupts = <0 2 4>, <0 3 4>;
+			clocks = <&timclk2 &timclk3>;
+			clock-names = "apb_pclk";
+			status = "disabled";
+		};
+
+		timer2: timer at fca01000 {
+			compatible = "arm,sp804", "arm,primecell";
+			reg = <0xfca01000 0x1000>;
+			/* timer20 & timer21 */
+			interrupts = <0 4 4>, <0 5 4>;
+			clocks = <&timclk4 &timclk5>;
+			clock-names = "apb_pclk";
+			status = "disabled";
+		};
+
+		timer3: timer at fca02000 {
+			compatible = "arm,sp804", "arm,primecell";
+			reg = <0xfca02000 0x1000>;
+			/* timer30 & timer31 */
+			interrupts = <0 6 4>, <0 7 4>;
+			clocks = <&timclk6 &timclk7>;
+			clock-names = "apb_pclk";
+			status = "disabled";
+		};
+
+		timer4: timer at fca03000 {
+			compatible = "arm,sp804", "arm,primecell";
+			reg = <0xfca03000 0x1000>;
+			/* timer40 & timer41 */
+			interrupts = <0 96 4>, <0 97 4>;
+			clocks = <&timclk8 &timclk9>;
+			clock-names = "apb_pclk";
+			status = "disabled";
+		};
+
+		uart0: uart at fcb00000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0xfcb00000 0x1000>;
+			interrupts = <0 20 4>;
+			clocks = <&uartclk0>;
+			clock-names = "apb_pclk";
+			status = "disabled";
+		};
+
+		uart1: uart at fcb01000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0xfcb01000 0x1000>;
+			interrupts = <0 21 4>;
+			clocks = <&uartclk1>;
+			clock-names = "apb_pclk";
+			status = "disabled";
+		};
+
+		uart2: uart at fcb02000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0xfcb02000 0x1000>;
+			interrupts = <0 22 4>;
+			clocks = <&uartclk2>;
+			clock-names = "apb_pclk";
+			status = "disabled";
+		};
+
+		uart3: uart at fcb03000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0xfcb03000 0x1000>;
+			interrupts = <0 23 4>;
+			clocks = <&uartclk3>;
+			clock-names = "apb_pclk";
+			status = "disabled";
+		};
+
+		uart4: uart at fcb04000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0xfcb04000 0x1000>;
+			interrupts = <0 24 4>;
+			clocks = <&uartclk4>;
+			clock-names = "apb_pclk";
+			status = "disabled";
+		};
+
+		gpio0: gpio at fc806000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0xfc806000 0x1000>;
+			interrupts = <0 64 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 2 0 1 &pmx0 3 0 1 &pmx0 4 0 1
+					&pmx0 5 0 1 &pmx0 6 1 1 &pmx0 7 2 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&gpioclk0>;
+			clock-names = "apb_pclk";
+			status = "disable";
+		};
+
+		gpio1: gpio at fc807000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0xfc807000 0x1000>;
+			interrupts = <0 65 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 0 3 1 &pmx0 1 3 1 &pmx0 2 3 1
+					&pmx0 3 3 1 &pmx0 4 3 1 &pmx0 5 4 1
+					&pmx0 6 5 1 &pmx0 7 6 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&gpioclk1>;
+			clock-names = "apb_pclk";
+			status = "disable";
+		};
+
+		gpio2: gpio at fc808000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0xfc808000 0x1000>;
+			interrupts = <0 66 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 0 7 1 &pmx0 1 8 1 &pmx0 2 9 1
+					&pmx0 3 10 1 &pmx0 4 3 1 &pmx0 5 3 1
+					&pmx0 6 3 1 &pmx0 7 3 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&gpioclk2>;
+			clock-names = "apb_pclk";
+			status = "disable";
+		};
+
+		gpio3: gpio at fc809000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0xfc809000 0x1000>;
+			interrupts = <0 67 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 0 3 1 &pmx0 1 3 1 &pmx0 2 3 1
+					&pmx0 3 3 1 &pmx0 4 11 1 &pmx0 5 11 1
+					&pmx0 6 11 1 &pmx0 7 11 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&gpioclk3>;
+			clock-names = "apb_pclk";
+			status = "disable";
+		};
+
+		gpio4: gpio at fc80a000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0xfc80a000 0x1000>;
+			interrupts = <0 68 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 0 11 1 &pmx0 1 11 1 &pmx0 2 11 1
+					&pmx0 3 11 1 &pmx0 4 12 1 &pmx0 5 12 1
+					&pmx0 6 13 1 &pmx0 7 13 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&gpioclk4>;
+			clock-names = "apb_pclk";
+			status = "disable";
+		};
+
+		gpio5: gpio at fc80b000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0xfc80b000 0x1000>;
+			interrupts = <0 69 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 0 14 1 &pmx0 1 15 1 &pmx0 2 16 1
+					&pmx0 3 16 1 &pmx0 4 16 1 &pmx0 5 16 1
+					&pmx0 6 16 1 &pmx0 7 16 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&gpioclk5>;
+			clock-names = "apb_pclk";
+			status = "disable";
+		};
+
+		gpio6: gpio at fc80c000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0xfc80c000 0x1000>;
+			interrupts = <0 70 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 0 16 1 &pmx0 1 16 1 &pmx0 2 17 1
+					&pmx0 3 17 1 &pmx0 4 18 1 &pmx0 5 18 1
+					&pmx0 6 18 1 &pmx0 7 19 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&gpioclk6>;
+			clock-names = "apb_pclk";
+			status = "disable";
+		};
+
+		gpio7: gpio at fc80d000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0xfc80d000 0x1000>;
+			interrupts = <0 71 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 0 19 1 &pmx0 1 20 1 &pmx0 2 21 1
+					&pmx0 3 22 1 &pmx0 4 23 1 &pmx0 5 24 1
+					&pmx0 6 25 1 &pmx0 7 26 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&gpioclk7>;
+			clock-names = "apb_pclk";
+			status = "disable";
+		};
+
+		gpio8: gpio at fc80e000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0xfc80e000 0x1000>;
+			interrupts = <0 72 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 0 27 1 &pmx0 1 28 1 &pmx0 2 29 1
+					&pmx0 3 30 1 &pmx0 4 31 1 &pmx0 5 32 1
+					&pmx0 6 33 1 &pmx0 7 34 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&gpioclk8>;
+			clock-names = "apb_pclk";
+			status = "disable";
+		};
+
+		gpio9: gpio at fc80f000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0xfc80f000 0x1000>;
+			interrupts = <0 73 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 0 35 1 &pmx0 1 36 1 &pmx0 2 37 1
+					&pmx0 3 38 1 &pmx0 4 39 1 &pmx0 5 40 1
+					&pmx0 6 41 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&gpioclk9>;
+			clock-names = "apb_pclk";
+			status = "disable";
+		};
+
+		gpio10: gpio at fc810000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0xfc810000 0x1000>;
+			interrupts = <0 74 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 2 43 1 &pmx0 3 44 1 &pmx0 4 45 1
+					&pmx0 5 45 1 &pmx0 6 46 1 &pmx0 7 46 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&gpioclk10>;
+			clock-names = "apb_pclk";
+			status = "disable";
+		};
+
+		gpio11: gpio at fc811000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0xfc811000 0x1000>;
+			interrupts = <0 75 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 0 47 1 &pmx0 1 47 1 &pmx0 2 47 1
+					&pmx0 3 47 1 &pmx0 4 47 1 &pmx0 5 48 1
+					&pmx0 6 49 1 &pmx0 7 49 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&gpioclk11>;
+			clock-names = "apb_pclk";
+			status = "disable";
+		};
+
+		gpio12: gpio at fc812000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0xfc812000 0x1000>;
+			interrupts = <0 76 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 0 49 1 &pmx0 1 50 1 &pmx0 2 49 1
+					&pmx0 3 49 1 &pmx0 4 51 1 &pmx0 5 51 1
+					&pmx0 6 51 1 &pmx0 7 52 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&gpioclk12>;
+			clock-names = "apb_pclk";
+			status = "disable";
+		};
+
+		gpio13: gpio at fc813000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0xfc813000 0x1000>;
+			interrupts = <0 77 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 0 51 1 &pmx0 1 51 1 &pmx0 2 53 1
+					&pmx0 3 53 1 &pmx0 4 53 1 &pmx0 5 54 1
+					&pmx0 6 55 1 &pmx0 7 56 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&gpioclk13>;
+			clock-names = "apb_pclk";
+			status = "disable";
+		};
+
+		gpio14: gpio at fc814000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0xfc814000 0x1000>;
+			interrupts = <0 78 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 0 57 1 &pmx0 1 97 1 &pmx0 2 97 1
+					&pmx0 3 58 1 &pmx0 4 59 1 &pmx0 5 60 1
+					&pmx0 6 60 1 &pmx0 7 61 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&gpioclk14>;
+			clock-names = "apb_pclk";
+			status = "disable";
+		};
+
+		gpio15: gpio at fc815000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0xfc815000 0x1000>;
+			interrupts = <0 79 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 0 61 1 &pmx0 1 62 1 &pmx0 2 62 1
+					&pmx0 3 63 1 &pmx0 4 63 1 &pmx0 5 64 1
+					&pmx0 6 64 1 &pmx0 7 65 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&gpioclk15>;
+			clock-names = "apb_pclk";
+			status = "disable";
+		};
+
+		gpio16: gpio at fc816000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0xfc816000 0x1000>;
+			interrupts = <0 80 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 0 66 1 &pmx0 1 67 1 &pmx0 2 68 1
+					&pmx0 3 69 1 &pmx0 4 70 1 &pmx0 5 71 1
+					&pmx0 6 72 1 &pmx0 7 73 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&gpioclk16>;
+			clock-names = "apb_pclk";
+			status = "disable";
+		};
+
+		gpio17: gpio at fc817000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0xfc817000 0x1000>;
+			interrupts = <0 81 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 0 74 1 &pmx0 1 75 1 &pmx0 2 76 1
+					&pmx0 3 77 1 &pmx0 4 78 1 &pmx0 5 79 1
+					&pmx0 6 80 1 &pmx0 7 81 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&gpioclk17>;
+			clock-names = "apb_pclk";
+			status = "disable";
+		};
+
+		gpio18: gpio at fc818000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0xfc818000 0x1000>;
+			interrupts = <0 82 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 0 82 1 &pmx0 1 83 1 &pmx0 2 83 1
+					&pmx0 3 84 1 &pmx0 4 84 1 &pmx0 5 85 1
+					&pmx0 6 86 1 &pmx0 7 87 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&gpioclk18>;
+			clock-names = "apb_pclk";
+			status = "disable";
+		};
+
+		gpio19: gpio at fc819000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0xfc819000 0x1000>;
+			interrupts = <0 83 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 0 87 1 &pmx0 1 87 1 &pmx0 2 88 1
+					&pmx0 3 88 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&gpioclk19>;
+			clock-names = "apb_pclk";
+			status = "disable";
+		};
+
+		gpio20: gpio at fc81a000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0xfc81a000 0x1000>;
+			interrupts = <0 84 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 0 89 1 &pmx0 1 89 1 &pmx0 2 90 1
+					&pmx0 3 90 1 &pmx0 4 91 1 &pmx0 5 92 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&gpioclk20>;
+			clock-names = "apb_pclk";
+			status = "disable";
+		};
+
+		gpio21: gpio at fc81b000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0xfc81b000 0x1000>;
+			interrupts = <0 85 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 3 94 1 &pmx0 7 96 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&gpioclk21>;
+			clock-names = "apb_pclk";
+			status = "disable";
+		};
+
+		pmx0: pinmux at fc803000 {
+			compatible = "pinctrl-single";
+			reg = <0xfc803000 0x188>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			#gpio-range-cells = <3>;
+			ranges;
+
+			pinctrl-single,register-width = <32>;
+			pinctrl-single,function-mask = <7>;
+			/* pin base, nr pins & gpio function */
+			pinctrl-single,gpio-range = <&range 0 3 0 &range 3 9 1
+						&range 12 1 0 &range 13 29 1
+						&range 43 1 0 &range 44 49 1
+						&range 94 1 1 &range 96 2 1>;
+
+			range: gpio-range {
+				#pinctrl-single,gpio-range-cells = <3>;
+			};
+		};
+
+		pmx1: pinmux at fc803800 {
+			compatible = "pinconf-single";
+			reg = <0xfc803800 0x2dc>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			pinctrl-single,register-width = <32>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/hi4511.dts b/arch/arm/boot/dts/hi4511.dts
new file mode 100644
index 0000000..0a50faf
--- /dev/null
+++ b/arch/arm/boot/dts/hi4511.dts
@@ -0,0 +1,743 @@
+/*
+ *  Copyright (C) 2012-2013 Linaro Ltd.
+ *  Author: Haojian Zhuang <haojian.zhuang@linaro.org>
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License version 2 as
+ *  publishhed by the Free Software Foundation.
+ */
+
+/dts-v1/;
+/include/ "hi3620.dtsi"
+
+/ {
+	model = "Hisilicon Hi4511 Development Board";
+	compatible = "hisilicon,hi3620-hi4511";
+
+	chosen {
+		bootargs = "console=ttyAMA0,115200 root=/dev/nfs nfsroot=192.168.1.100:/nfsroot/ ip=192.168.1.101:192.168.1.100::255.255.255.0::eth0:on mem=512m earlyprintk";
+	};
+
+	memory {
+		reg = <0x00000000 0x20000000>;
+	};
+
+	amba {
+		timer0: timer at fc800000 {
+			arm,sp804-clockevent = <0>;
+			status = "ok";
+		};
+		timer1: timer at fc801000 {
+			arm,sp804-clocksource = <0x20>;
+			status = "ok";
+		};
+
+		uart0: uart at fcb00000 {	/* console */
+/*
+			pinctrl-names = "default", "idle";
+			pinctrl-0 = <&uart0_pmx_func &uart0_cfg_func>;
+			pinctrl-1 = <&uart0_pmx_idle &uart0_cfg_idle>;
+*/
+			status = "ok";
+		};
+
+		uart1: uart at fcb01000 { /* modem */
+			pinctrl-names = "default", "idle";
+			pinctrl-0 = <&uart1_pmx_func &uart1_cfg_func>;
+			pinctrl-1 = <&uart1_pmx_idle &uart1_cfg_idle>;
+			status = "ok";
+		};
+
+		uart2: uart at fcb02000 { /* audience */
+			pinctrl-names = "default", "idle";
+			pinctrl-0 = <&uart2_pmx_func &uart2_cfg_func>;
+			pinctrl-1 = <&uart2_pmx_idle &uart2_cfg_idle>;
+			status = "ok";
+		};
+
+		uart3: uart at fcb03000 {
+			pinctrl-names = "default", "idle";
+			pinctrl-0 = <&uart3_pmx_func &uart3_cfg_func>;
+			pinctrl-1 = <&uart3_pmx_idle &uart3_cfg_idle>;
+			status = "ok";
+		};
+
+		uart4: uart at fcb04000 {
+			pinctrl-names = "default", "idle";
+			pinctrl-0 = <&uart4_pmx_func &uart4_cfg_func>;
+			pinctrl-1 = <&uart4_pmx_idle &uart4_cfg_func>;
+			status = "ok";
+		};
+
+		gpio0: gpio at fc806000 {
+			status = "ok";
+		};
+
+		gpio1: gpio at fc807000 {
+			status = "ok";
+		};
+
+		gpio2: gpio at fc808000 {
+			status = "ok";
+		};
+
+		gpio3: gpio at fc809000 {
+			status = "ok";
+		};
+
+		gpio4: gpio at fc80a000 {
+			status = "ok";
+		};
+
+		gpio5: gpio at fc80b000 {
+			status = "ok";
+		};
+
+		gpio6: gpio at fc80c000 {
+			status = "ok";
+		};
+
+		gpio7: gpio at fc80d000 {
+			status = "ok";
+		};
+
+		gpio8: gpio at fc80e000 {
+			status = "ok";
+		};
+
+		gpio9: gpio at fc80f000 {
+			status = "ok";
+		};
+
+		gpio10: gpio at fc810000 {
+			status = "ok";
+		};
+
+		gpio11: gpio at fc811000 {
+			status = "ok";
+		};
+
+		gpio12: gpio at fc812000 {
+			status = "ok";
+		};
+
+		gpio13: gpio at fc813000 {
+			status = "ok";
+		};
+
+		gpio14: gpio at fc814000 {
+			status = "ok";
+		};
+
+		gpio15: gpio at fc815000 {
+			status = "ok";
+		};
+
+		gpio16: gpio at fc816000 {
+			status = "ok";
+		};
+
+		gpio17: gpio at fc817000 {
+			status = "ok";
+		};
+
+		gpio18: gpio at fc818000 {
+			status = "ok";
+		};
+
+		gpio19: gpio at fc819000 {
+			status = "ok";
+		};
+
+		gpio20: gpio at fc81a000 {
+			status = "ok";
+		};
+
+		gpio21: gpio at fc81b000 {
+			status = "ok";
+		};
+
+		gpio-keys {
+			compatible = "gpio-keys";
+
+			call {
+				label = "call";
+				gpios = <&gpio17 2 0>;
+				linux,code = <169>;	/* KEY_PHONE */
+			};
+		};
+
+		pmx0: pinmux at fc803000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c0_pmx_func>;
+
+			board_pmx_pins: pinmux_board_pmx_pins {
+				pinctrl-single,pins = <
+					0x008 0x0	/* GPIO -- eFUSE_DOUT */
+					0x100 0x0	/* USIM_CLK & USIM_DATA (IOMG63) */
+					0x104 0x0	/* USIM_RST (IOMG96) */
+				>;
+			};
+			uart0_pmx_func: pinmux_uart0_pins at 0  {
+				pinctrl-single,pins = <
+					0x0f0 0x0
+					0x0f4 0x0	/* UART0_RX & UART0_TX */
+				>;
+			};
+			uart0_pmx_idle: pinmux_uart0_pins at 1 {
+				pinctrl-single,pins = <
+					/*0x0f0 0x1*/	/* UART0_CTS & UART0_RTS */
+					0x0f4 0x1	/* UART0_RX & UART0_TX */
+				>;
+			};
+			uart1_pmx_func: pinmux_uart1_pins at 0  {
+				pinctrl-single,pins = <
+					0x0f8 0x0	/* UART1_CTS & UART1_RTS (IOMG61) */
+					0x0fc 0x0	/* UART1_RX & UART1_TX (IOMG62) */
+				>;
+			};
+			uart1_pmx_idle: pinmux_uart1_pins at 1  {
+				pinctrl-single,pins = <
+					0x0f8 0x1	/* GPIO (IOMG61) */
+					0x0fc 0x1	/* GPIO (IOMG62) */
+				>;
+			};
+			uart2_pmx_func: pinmux_uart2_pins at 0 {
+				pinctrl-single,pins = <
+					0x104 0x2	/* UART2_RXD (IOMG96) */
+					0x108 0x2	/* UART2_TXD (IOMG64) */
+				>;
+			};
+			uart2_pmx_idle: pinmux_uart2_pins at 1 {
+				pinctrl-single,pins = <
+					0x104 0x1	/* GPIO (IOMG96) */
+					0x108 0x1	/* GPIO (IOMG64) */
+				>;
+			};
+			uart3_pmx_func: pinmux_uart3_pins at 0 {
+				pinctrl-single,pins = <
+					0x160 0x2	/* UART3_CTS & UART3_RTS (IOMG85) */
+					0x164 0x2	/* UART3_RXD & UART3_TXD (IOMG86) */
+				>;
+			};
+			uart3_pmx_idle: pinmux_uart3_pins at 1 {
+				pinctrl-single,pins = <
+					0x160 0x1	/* GPIO (IOMG85) */
+					0x164 0x1	/* GPIO (IOMG86) */
+				>;
+			};
+			uart4_pmx_func: pinmux_uart4_pins at 0 {
+				pinctrl-single,pins = <
+					0x168 0x0	/* UART4_CTS & UART4_RTS (IOMG87) */
+					0x16c 0x0	/* UART4_RXD (IOMG88) */
+					0x170 0x0	/* UART4_TXD (IOMG93) */
+				>;
+			};
+			uart4_pmx_idle: pinmux_uart4_pins at 1 {
+				pinctrl-single,pins = <
+					0x168 0x1	/* GPIO (IOMG87) */
+					0x16c 0x1	/* GPIO (IOMG88) */
+					0x170 0x1	/* GPIO (IOMG93) */
+				>;
+			};
+			i2c0_pmx_func: pinmux_i2c0_pins at 0 {
+				pinctrl-single,pins = <
+					0x0b4 0x0	/* I2C0_SCL & I2C0_SDA (IOMG45) */
+				>;
+			};
+			i2c0_pmx_idle: pinmux_i2c0_pins at 1 {
+				pinctrl-single,pins = <
+					0x0b4 0x1	/* GPIO (IOMG45) */
+				>;
+			};
+			i2c1_pmx_func: pinmux_i2c1_pins at 0 {
+				pinctrl-single,pins = <
+					0x0b8 0x0	/* I2C1_SCL & I2C1_SDA (IOMG46) */
+				>;
+			};
+			i2c1_pmx_idle: pinmux_i2c1_pins at 1 {
+				pinctrl-single,pins = <
+					0x0b8 0x1	/* GPIO (IOMG46) */
+				>;
+			};
+			i2c2_pmx_func: pinmux_i2c2_pins at 0 {
+				pinctrl-single,pins = <
+					0x068 0x0	/* I2C2_SCL (IOMG26) */
+					0x06c 0x0	/* I2C2_SDA (IOMG27) */
+				>;
+			};
+			i2c2_pmx_idle: pinmux_i2c2_pins at 0 {
+				pinctrl-single,pins = <
+					0x068 0x1	/* GPIO (IOMG26) */
+					0x06c 0x1	/* GPIO (IOMG27) */
+				>;
+			};
+			i2c3_pmx_func: pinmux_i2c3_pins at 0 {
+				pinctrl-single,pins = <
+					0x050 0x2	/* I2C3_SCL (IOMG20) */
+					0x054 0x2	/* I2C3_SDA (IOMG21) */
+				>;
+			};
+			i2c3_pmx_idle: pinmux_i2c3_pins at 0 {
+				pinctrl-single,pins = <
+					0x050 0x1	/* GPIO (IOMG20) */
+					0x054 0x1	/* GPIO (IOMG21) */
+				>;
+			};
+			spi0_pmx_func: pinmux_spi0_pins at 0 {
+				pinctrl-single,pins = <
+					0x0d4 0x0	/* SPI0_CLK/SPI0_DI/SPI0_DO (IOMG53) */
+					0x0d8 0x0	/* SPI0_CS0 (IOMG54) */
+					0x0dc 0x0	/* SPI0_CS1 (IOMG55) */
+					0x0e0 0x0	/* SPI0_CS2 (IOMG56) */
+					0x0e4 0x0	/* SPI0_CS3 (IOMG57) */
+				>;
+			};
+			spi0_pmx_idle: pinmux_spi0_pins at 1 {
+				pinctrl-single,pins = <
+					0x0d4 0x1	/* GPIO (IOMG53) */
+					0x0d8 0x1	/* GPIO (IOMG54) */
+					0x0dc 0x1	/* GPIO (IOMG55) */
+					0x0e0 0x1	/* GPIO (IOMG56) */
+					0x0e4 0x1	/* GPIO (IOMG57) */
+				>;
+			};
+			spi1_pmx_func: pinmux_spi1_pins at 0 {
+				pinctrl-single,pins = <
+					0x184 0x0	/* SPI1_CLK/SPI1_DI (IOMG98) */
+					0x0e8 0x0	/* SPI1_DO (IOMG58) */
+					0x0ec 0x0	/* SPI1_CS (IOMG95) */
+				>;
+			};
+			spi1_pmx_idle: pinmux_spi1_pins at 1 {
+				pinctrl-single,pins = <
+					0x184 0x1	/* GPIO (IOMG98) */
+					0x0e8 0x1	/* GPIO (IOMG58) */
+					0x0ec 0x1	/* GPIO (IOMG95) */
+				>;
+			};
+			kpc_pmx_func: pinmux_kpc_pins at 0 {
+				pinctrl-single,pins = <
+					0x12c 0x0	/* KEY_IN0 (IOMG73) */
+					0x130 0x0	/* KEY_IN1 (IOMG74) */
+					0x134 0x0	/* KEY_IN2 (IOMG75) */
+					0x10c 0x0	/* KEY_OUT0 (IOMG65) */
+					0x110 0x0	/* KEY_OUT1 (IOMG66) */
+					0x114 0x0	/* KEY_OUT2 (IOMG67) */
+				>;
+			};
+			kpc_pmx_idle: pinmux_kpc_pins at 1 {
+				pinctrl-single,pins = <
+					0x12c 0x1	/* GPIO (IOMG73) */
+					0x130 0x1	/* GPIO (IOMG74) */
+					0x134 0x1	/* GPIO (IOMG75) */
+					0x10c 0x1	/* GPIO (IOMG65) */
+					0x110 0x1	/* GPIO (IOMG66) */
+					0x114 0x1	/* GPIO (IOMG67) */
+				>;
+			};
+			gpio_key_func: pinmux_gpiokey_pins {
+				pinctrl-single,pins = <
+					0x10c 0x1	/* KEY_OUT0/GPIO (IOMG65) */
+					0x130 0x1	/* KEY_IN1/GPIO (IOMG74) */
+				>;
+			};
+			emmc_pmx_func: pinmux_emmc_pins at 0 {
+				pinctrl-single,pins = <
+					0x030 0x2	/* eMMC_CMD/eMMC_CLK (IOMG12) */
+					0x018 0x0	/* NAND_CS3_N (IOMG6) */
+					0x024 0x0	/* NAND_BUSY2_N (IOMG8) */
+					0x028 0x0	/* NAND_BUSY3_N (IOMG9) */
+					0x02c 0x2	/* eMMC_DATA[0:7] (IOMG10) */
+				>;
+			};
+			emmc_pmx_idle: pinmux_emmc_pins at 1 {
+				pinctrl-single,pins = <
+					0x030 0x0	/* GPIO (IOMG12) */
+					0x018 0x1	/* GPIO (IOMG6) */
+					0x024 0x1	/* GPIO (IOMG8) */
+					0x028 0x1	/* GPIO (IOMG9) */
+					0x02c 0x1	/* GPIO (IOMG10) */
+				>;
+			};
+			sd_pmx_func: pinmux_sd_pins at 0 {
+				pinctrl-single,pins = <
+					0x0bc 0x0	/* SD_CLK/SD_CMD/SD_DATA0/SD_DATA1/SD_DATA2 (IOMG47) */
+					0x0c0 0x0	/* SD_DATA3 (IOMG48) */
+				>;
+			};
+			sd_pmx_idle: pinmux_sd_pins at 1 {
+				pinctrl-single,pins = <
+					0x0bc 0x1	/* GPIO (IOMG47) */
+					0x0c0 0x1	/* GPIO (IOMG48) */
+				>;
+			};
+			nand_pmx_func: pinmux_nand_pins at 0 {
+				pinctrl-single,pins = <
+					0x00c 0x0	/* NAND_ALE/NAND_CLE/.../NAND_DATA[0:7] (IOMG3) */
+					0x010 0x0	/* NAND_CS1_N (IOMG4) */
+					0x014 0x0	/* NAND_CS2_N (IOMG5) */
+					0x018 0x0	/* NAND_CS3_N (IOMG6) */
+					0x01c 0x0	/* NAND_BUSY0_N (IOMG94) */
+					0x020 0x0	/* NAND_BUSY1_N (IOMG7) */
+					0x024 0x0	/* NAND_BUSY2_N (IOMG8) */
+					0x028 0x0	/* NAND_BUSY3_N (IOMG9) */
+					0x02c 0x0	/* NAND_DATA[8:15] (IOMG10) */
+				>;
+			};
+			nand_pmx_idle: pinmux_nand_pins at 1 {
+				pinctrl-single,pins = <
+					0x00c 0x1	/* GPIO (IOMG3) */
+					0x010 0x1	/* GPIO (IOMG4) */
+					0x014 0x1	/* GPIO (IOMG5) */
+					0x018 0x1	/* GPIO (IOMG6) */
+					0x01c 0x1	/* GPIO (IOMG94) */
+					0x020 0x1	/* GPIO (IOMG7) */
+					0x024 0x1	/* GPIO (IOMG8) */
+					0x028 0x1	/* GPIO (IOMG9) */
+					0x02c 0x1	/* GPIO (IOMG10) */
+				>;
+			};
+			sdio_pmx_func: pinmux_sdio_pins at 0 {
+				pinctrl-single,pins = <
+					0x0c4 0x0	/* SDIO_CLK/SDIO_CMD/SDIO_DATA[0:3] (IOMG49) */
+				>;
+			};
+			sdio_pmx_idle: pinmux_sdio_pins at 1 {
+				pinctrl-single,pins = <
+					0x0c4 0x1	/* GPIO (IOMG49) */
+				>;
+			};
+			audio_out_pmx_func: pinmux_audio_pins at 0 {
+				pinctrl-single,pins = <
+					0x0f0 0x1	/* GPIO (IOMG59), audio spk & earphone */
+				>;
+			};
+		};
+
+		pmx1: pinmux at fc803800 {
+			pinctrl-names = "default";
+			pinctrl-0 = <	&board_pu_pins &board_pd_pins &board_pd_ps_pins
+					&board_np_pins &board_ps_pins &kpc_cfg_func
+					&audio_out_cfg_func>;
+			board_pu_pins: pinmux_board_pu_pins {
+				pinctrl-single,pins = <
+					0x014 0		/* GPIO_158 (IOCFG2) */
+					0x018 0		/* GPIO_159 (IOCFG3) */
+					0x01c 0		/* BOOT_MODE0 (IOCFG4) */
+					0x020 0		/* BOOT_MODE1 (IOCFG5) */
+				>;
+				pinctrl-single,bias-pulldown = <0 2 0 2>;
+				pinctrl-single,bias-pullup = <1 1 0 1>;
+			};
+			board_pd_pins: pinmux_board_pd_pins {
+				pinctrl-single,pins = <
+					0x038 0		/* eFUSE_DOUT (IOCFG11) */
+					0x150 0		/* ISP_GPIO8 (IOCFG93) */
+					0x154 0		/* ISP_GPIO9 (IOCFG94) */
+				>;
+				pinctrl-single,bias-pulldown = <2 2 0 2>;
+				pinctrl-single,bias-pullup = <0 1 0 1>;
+			};
+			board_pd_ps_pins: pinmux_board_pd_ps_pins {
+				pinctrl-single,pins = <
+					0x2d8 0		/* CLK_OUT0 (IOCFG190) */
+					0x004 0		/* PMU_SPI_DATA (IOCFG192) */
+				>;
+				pinctrl-single,bias-pulldown = <2 2 0 2>;
+				pinctrl-single,bias-pullup = <0 1 0 1>;
+				pinctrl-single,drive-strength = <0x30 0xf0>;
+			};
+			board_np_pins: pinmux_board_np_pins {
+				pinctrl-single,pins = <
+					0x24c 0		/* KEYPAD_OUT7 (IOCFG155) */
+				>;
+				pinctrl-single,bias-pulldown = <0 2 0 2>;
+				pinctrl-single,bias-pullup = <0 1 0 1>;
+			};
+			board_ps_pins: pinmux_board_ps_pins {
+				pinctrl-single,pins = <
+					0x000 0		/* PMU_SPI_CLK (IOCFG191) */
+					0x008 0		/* PMU_SPI_CS_N (IOCFG193) */
+				>;
+				pinctrl-single,drive-strength = <0x30 0xf0>;
+			};
+			uart0_cfg_func: pinmux_uart0_pins at 2 {
+				pinctrl-single,pins = <
+					0x208 0		/* UART0_RXD (IOCFG138) */
+					0x20c 0		/* UART0_TXD (IOCFG139) */
+				>;
+				pinctrl-single,bias-pulldown = <0 2 0 2>;
+				pinctrl-single,bias-pullup = <0 1 0 1>;
+			};
+			uart0_cfg_idle: pinmux_uart0_pins at 3 {
+				pinctrl-single,pins = <
+					0x208 0		/* UART0_RXD (IOCFG138) */
+					0x20c 0		/* UART0_TXD (IOCFG139) */
+				>;
+				pinctrl-single,bias-pulldown = <2 2 0 2>;
+				pinctrl-single,bias-pullup = <0 1 0 1>;
+			};
+			uart1_cfg_func: pinmux_uart1_pins at 2 {
+				pinctrl-single,pins = <
+					0x210 0		/* UART1_CTS (IOCFG140) */
+					0x214 0		/* UART1_RTS (IOCFG141) */
+					0x218 0		/* UART1_RXD (IOCFG142) */
+					0x21c 0		/* UART1_TXD (IOCFG143) */
+				>;
+				pinctrl-single,bias-pulldown = <0 2 0 2>;
+				pinctrl-single,bias-pullup = <0 1 0 1>;
+			};
+			uart1_cfg_idle: pinmux_uart1_pins at 3 {
+				pinctrl-single,pins = <
+					0x210 0		/* UART1_CTS (IOCFG140) */
+					0x214 0		/* UART1_RTS (IOCFG141) */
+					0x218 0		/* UART1_RXD (IOCFG142) */
+					0x21c 0		/* UART1_TXD (IOCFG143) */
+				>;
+				pinctrl-single,bias-pulldown = <2 2 0 2>;
+				pinctrl-single,bias-pullup = <0 1 0 1>;
+			};
+			uart2_cfg_func: pinmux_uart2_pins at 2 {
+				pinctrl-single,pins = <
+					0x220 0		/* UART2_CTS (IOCFG144) */
+					0x224 0		/* UART2_RTS (IOCFG145) */
+					0x228 0		/* UART2_RXD (IOCFG146) */
+					0x22c 0		/* UART2_TXD (IOCFG147) */
+				>;
+				pinctrl-single,bias-pulldown = <0 2 0 2>;
+				pinctrl-single,bias-pullup = <0 1 0 1>;
+			};
+			uart2_cfg_idle: pinmux_uart2_pins at 3 {
+				pinctrl-single,pins = <
+					0x220 0		/* GPIO (IOCFG144) */
+					0x224 0		/* GPIO (IOCFG145) */
+					0x228 0		/* GPIO (IOCFG146) */
+					0x22c 0		/* GPIO (IOCFG147) */
+				>;
+				pinctrl-single,bias-pulldown = <2 2 0 2>;
+				pinctrl-single,bias-pullup = <0 1 0 1>;
+			};
+			uart3_cfg_func: pinmux_uart3_pins at 2 {
+				pinctrl-single,pins = <
+					0x294 0		/* UART3_CTS (IOCFG173) */
+					0x298 0		/* UART3_RTS (IOCFG174) */
+					0x29c 0		/* UART3_RXD (IOCFG175) */
+					0x2a0 0		/* UART3_TXD (IOCFG176) */
+				>;
+				pinctrl-single,bias-pulldown = <0 2 0 2>;
+				pinctrl-single,bias-pullup = <0 1 0 1>;
+			};
+			uart3_cfg_idle: pinmux_uart3_pins at 3 {
+				pinctrl-single,pins = <
+					0x294 0		/* UART3_CTS (IOCFG173) */
+					0x298 0		/* UART3_RTS (IOCFG174) */
+					0x29c 0		/* UART3_RXD (IOCFG175) */
+					0x2a0 0		/* UART3_TXD (IOCFG176) */
+				>;
+				pinctrl-single,bias-pulldown = <2 2 0 2>;
+				pinctrl-single,bias-pullup = <0 1 0 1>;
+			};
+			uart4_cfg_func: pinmux_uart4_pins at 2 {
+				pinctrl-single,pins = <
+					0x2a4 0		/* UART4_CTS (IOCFG177) */
+					0x2a8 0		/* UART4_RTS (IOCFG178) */
+					0x2ac 0		/* UART4_RXD (IOCFG179) */
+					0x2b0 0		/* UART4_TXD (IOCFG180) */
+				>;
+				pinctrl-single,bias-pulldown = <0 2 0 2>;
+				pinctrl-single,bias-pullup = <0 1 0 1>;
+			};
+			i2c0_cfg_func: pinmux_i2c0_pins at 2 {
+				pinctrl-single,pins = <
+					0x17c 0		/* I2C0_SCL (IOCFG103) */
+					0x180 0		/* I2C0_SDA (IOCFG104) */
+				>;
+				pinctrl-single,bias-pulldown = <0 2 0 2>;
+				pinctrl-single,bias-pullup = <0 1 0 1>;
+				pinctrl-single,drive-strength = <0x30 0xf0>;
+			};
+			i2c1_cfg_func: pinmux_i2c1_pins at 2 {
+				pinctrl-single,pins = <
+					0x184 0		/* I2C1_SCL (IOCFG105) */
+					0x188 0		/* I2C1_SDA (IOCFG106) */
+				>;
+				pinctrl-single,bias-pulldown = <0 2 0 2>;
+				pinctrl-single,bias-pullup = <0 1 0 1>;
+				pinctrl-single,drive-strength = <0x30 0xf0>;
+			};
+			i2c2_cfg_func: pinmux_i2c2_pins at 2 {
+				pinctrl-single,pins = <
+					0x118 0		/* I2C2_SCL (IOCFG79) */
+					0x11c 0		/* I2C2_SDA (IOCFG80) */
+				>;
+				pinctrl-single,bias-pulldown = <0 2 0 2>;
+				pinctrl-single,bias-pullup = <0 1 0 1>;
+				pinctrl-single,drive-strength = <0x30 0xf0>;
+			};
+			i2c3_cfg_func: pinmux_i2c3_pins at 2 {
+				pinctrl-single,pins = <
+					0x100 0		/* I2C3_SCL (IOCFG73) */
+					0x104 0		/* I2C3_SDA (IOCFG74) */
+				>;
+				pinctrl-single,bias-pulldown = <0 2 0 2>;
+				pinctrl-single,bias-pullup = <0 1 0 1>;
+				pinctrl-single,drive-strength = <0x30 0xf0>;
+			};
+			spi0_cfg_func1: pinmux_spi0_pins at 2 {
+				pinctrl-single,pins = <
+					0x1d4 0		/* SPI0_CLK (IOCFG125) */
+					0x1d8 0		/* SPI0_DI (IOCFG126) */
+					0x1dc 0		/* SPI0_DO (IOCFG127) */
+				>;
+				pinctrl-single,bias-pulldown = <2 2 0 2>;
+				pinctrl-single,bias-pullup = <0 1 0 1>;
+				pinctrl-single,drive-strength = <0x30 0xf0>;
+			};
+			spi0_cfg_func2: pinmux_spi0_pins at 3 {
+				pinctrl-single,pins = <
+					0x1e0 0		/* SPI0_CS0 (IOCFG128) */
+					0x1e4 0		/* SPI0_CS1 (IOCFG129) */
+					0x1e8 0		/* SPI0_CS2 (IOCFG130 */
+					0x1ec 0		/* SPI0_CS3 (IOCFG131) */
+				>;
+				pinctrl-single,bias-pulldown = <0 2 0 2>;
+				pinctrl-single,bias-pullup = <1 1 0 1>;
+				pinctrl-single,drive-strength = <0x30 0xf0>;
+			};
+			spi1_cfg_func1: pinmux_spi1_pins at 2 {
+				pinctrl-single,pins = <
+					0x1f0 0		/* SPI1_CLK (IOCFG132) */
+					0x1f4 0		/* SPI1_DI (IOCFG133) */
+					0x1f8 0		/* SPI1_DO (IOCFG134) */
+				>;
+				pinctrl-single,bias-pulldown = <2 2 0 2>;
+				pinctrl-single,bias-pullup = <0 1 0 1>;
+				pinctrl-single,drive-strength = <0x30 0xf0>;
+			};
+			spi1_cfg_func2: pinmux_spi1_pins at 3 {
+				pinctrl-single,pins = <
+					0x1fc 0		/* SPI1_CS (IOCFG135) */
+				>;
+				pinctrl-single,bias-pulldown = <0 2 0 2>;
+				pinctrl-single,bias-pullup = <1 1 0 1>;
+				pinctrl-single,drive-strength = <0x30 0xf0>;
+			};
+			kpc_cfg_func: pinmux_kpc_pins at 2 {
+				pinctrl-single,pins = <
+					0x250 0		/* KEY_IN0 (IOCFG156) */
+					0x254 0		/* KEY_IN1 (IOCFG157) */
+					0x258 0		/* KEY_IN2 (IOCFG158) */
+					0x230 0		/* KEY_OUT0 (IOCFG148) */
+					0x234 0		/* KEY_OUT1 (IOCFG149) */
+					0x238 0		/* KEY_OUT2 (IOCFG150) */
+				>;
+				pinctrl-single,bias-pulldown = <2 2 0 2>;
+				pinctrl-single,bias-pullup = <0 1 0 1>;
+			};
+			emmc_cfg_func: pinmux_emmc_pins at 2 {
+				pinctrl-single,pins = <
+					0x0ac 0		/* eMMC_CMD (IOCFG40) */
+					0x0b0 0		/* eMMC_CLK (IOCFG41) */
+					0x058 0		/* NAND_CS3_N (IOCFG19) */
+					0x064 0		/* NAND_BUSY2_N (IOCFG22) */
+					0x068 0		/* NAND_BUSY3_N (IOCFG23) */
+					0x08c 0		/* NAND_DATA8 (IOCFG32) */
+					0x090 0		/* NAND_DATA9 (IOCFG33) */
+					0x094 0		/* NAND_DATA10 (IOCFG34) */
+					0x098 0		/* NAND_DATA11 (IOCFG35) */
+					0x09c 0		/* NAND_DATA12 (IOCFG36) */
+					0x0a0 0		/* NAND_DATA13 (IOCFG37) */
+					0x0a4 0		/* NAND_DATA14 (IOCFG38) */
+					0x0a8 0		/* NAND_DATA15 (IOCFG39) */
+				>;
+				pinctrl-single,bias-pulldown = <0 2 0 2>;
+				pinctrl-single,bias-pullup = <1 1 0 1>;
+				pinctrl-single,drive-strength = <0x30 0xf0>;
+			};
+			sd_cfg_func1: pinmux_sd_pins at 2 {
+				pinctrl-single,pins = <
+					0x18c 0		/* SD_CLK (IOCFG107) */
+					0x190 0		/* SD_CMD (IOCFG108) */
+				>;
+				pinctrl-single,bias-pulldown = <2 2 0 2>;
+				pinctrl-single,bias-pullup = <0 1 0 1>;
+				pinctrl-single,drive-strength = <0x30 0xf0>;
+			};
+			sd_cfg_func2: pinmux_sd_pins at 3 {
+				pinctrl-single,pins = <
+					0x194 0		/* SD_DATA0 (IOCFG109) */
+					0x198 0		/* SD_DATA1 (IOCFG110) */
+					0x19c 0		/* SD_DATA2 (IOCFG111) */
+					0x1a0 0		/* SD_DATA3 (IOCFG112) */
+				>;
+				pinctrl-single,bias-pulldown = <2 2 0 2>;
+				pinctrl-single,bias-pullup = <0 1 0 1>;
+				pinctrl-single,drive-strength = <0x70 0xf0>;
+			};
+			nand_cfg_func1: pinmux_nand_pins at 2 {
+				pinctrl-single,pins = <
+					0x03c 0		/* NAND_ALE (IOCFG12) */
+					0x040 0		/* NAND_CLE (IOCFG13) */
+					0x06c 0		/* NAND_DATA0 (IOCFG24) */
+					0x070 0		/* NAND_DATA1 (IOCFG25) */
+					0x074 0		/* NAND_DATA2 (IOCFG26) */
+					0x078 0		/* NAND_DATA3 (IOCFG27) */
+					0x07c 0		/* NAND_DATA4 (IOCFG28) */
+					0x080 0		/* NAND_DATA5 (IOCFG29) */
+					0x084 0		/* NAND_DATA6 (IOCFG30) */
+					0x088 0		/* NAND_DATA7 (IOCFG31) */
+					0x08c 0		/* NAND_DATA8 (IOCFG32) */
+					0x090 0		/* NAND_DATA9 (IOCFG33) */
+					0x094 0		/* NAND_DATA10 (IOCFG34) */
+					0x098 0		/* NAND_DATA11 (IOCFG35) */
+					0x09c 0		/* NAND_DATA12 (IOCFG36) */
+					0x0a0 0		/* NAND_DATA13 (IOCFG37) */
+					0x0a4 0		/* NAND_DATA14 (IOCFG38) */
+					0x0a8 0		/* NAND_DATA15 (IOCFG39) */
+				>;
+				pinctrl-single,bias-pulldown = <2 2 0 2>;
+				pinctrl-single,bias-pullup = <0 1 0 1>;
+				pinctrl-single,drive-strength = <0x30 0xf0>;
+			};
+			nand_cfg_func2: pinmux_nand_pins at 3 {
+				pinctrl-single,pins = <
+					0x044 0		/* NAND_RE_N (IOCFG14) */
+					0x048 0		/* NAND_WE_N (IOCFG15) */
+					0x04c 0		/* NAND_CS0_N (IOCFG16) */
+					0x050 0		/* NAND_CS1_N (IOCFG17) */
+					0x054 0		/* NAND_CS2_N (IOCFG18) */
+					0x058 0		/* NAND_CS3_N (IOCFG19) */
+					0x05c 0		/* NAND_BUSY0_N (IOCFG20) */
+					0x060 0		/* NAND_BUSY1_N (IOCFG21) */
+					0x064 0		/* NAND_BUSY2_N (IOCFG22) */
+					0x068 0		/* NAND_BUSY3_N (IOCFG23) */
+				>;
+				pinctrl-single,bias-pulldown = <0 2 0 2>;
+				pinctrl-single,bias-pullup = <1 1 0 1>;
+				pinctrl-single,drive-strength = <0x30 0xf0>;
+			};
+			sdio_cfg_func: pinmux_sdio_pins at 2 {
+				pinctrl-single,pins = <
+					0x1a4 0		/* SDIO0_CLK (IOCG113) */
+					0x1a8 0		/* SDIO0_CMD (IOCG114) */
+					0x1ac 0		/* SDIO0_DATA0 (IOCG115) */
+					0x1b0 0		/* SDIO0_DATA1 (IOCG116) */
+					0x1b4 0		/* SDIO0_DATA2 (IOCG117) */
+					0x1b8 0		/* SDIO0_DATA3 (IOCG118) */
+				>;
+				pinctrl-single,bias-pulldown = <2 2 0 2>;
+				pinctrl-single,bias-pullup = <0 1 0 1>;
+				pinctrl-single,drive-strength = <0x30 0xf0>;
+			};
+			audio_out_cfg_func: pinmux_audio_pins at 1 {
+				pinctrl-single,pins = <
+					0x200 0		/* GPIO (IOCFG136) */
+					0x204 0		/* GPIO (IOCFG137) */
+				>;
+				pinctrl-single,bias-pulldown = <2 2 0 2>;
+				pinctrl-single,bias-pullup = <0 1 0 1>;
+			};
+		};
+	};
+};
-- 
1.7.10.4

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 11/11] ARM: config: append arch hi3xxx into multi defconfig
  2013-03-13  5:05 [PATCH v3 00/11] add hisilicon SoC support Haojian Zhuang
                   ` (9 preceding siblings ...)
  2013-03-13  5:05 ` [PATCH v3 10/11] ARM: hi3xxx: enable hi4511 " Haojian Zhuang
@ 2013-03-13  5:05 ` Haojian Zhuang
  10 siblings, 0 replies; 44+ messages in thread
From: Haojian Zhuang @ 2013-03-13  5:05 UTC (permalink / raw)
  To: linux-arm-kernel

Append ARCH_HI3xxx (Hisilicon SoC) into multi_v7_defconfig.

Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
---
 arch/arm/configs/multi_v7_defconfig |    1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/configs/multi_v7_defconfig b/arch/arm/configs/multi_v7_defconfig
index e31d442..1891611 100644
--- a/arch/arm/configs/multi_v7_defconfig
+++ b/arch/arm/configs/multi_v7_defconfig
@@ -5,6 +5,7 @@ CONFIG_ARCH_MVEBU=y
 CONFIG_MACH_ARMADA_370=y
 CONFIG_MACH_ARMADA_XP=y
 CONFIG_ARCH_HIGHBANK=y
+CONFIG_ARCH_HI3xxx=y
 CONFIG_ARCH_SOCFPGA=y
 CONFIG_ARCH_SUNXI=y
 # CONFIG_ARCH_VEXPRESS_CORTEX_A5_A9_ERRATA is not set
-- 
1.7.10.4

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 03/11] clocksource: sp804: add device tree support
  2013-03-13  5:05 ` [PATCH v3 03/11] clocksource: sp804: add device tree support Haojian Zhuang
@ 2013-03-13 11:05   ` Pawel Moll
  2013-03-13 11:37     ` Haojian Zhuang
  2013-03-13 14:17     ` Rob Herring
  0 siblings, 2 replies; 44+ messages in thread
From: Pawel Moll @ 2013-03-13 11:05 UTC (permalink / raw)
  To: linux-arm-kernel

On Wed, 2013-03-13 at 05:05 +0000, Haojian Zhuang wrote:
> +++ b/Documentation/devicetree/bindings/timer/arm,sp804.txt
> @@ -0,0 +1,27 @@
> +ARM sp804 Dual Timers
> +---------------------------------------
> +
> +Required properties:
> +- compatible: Should be "arm,sp804" & "arm,primecell"
> +- interrupts: Should contain the list of Dual Timer interrupts
> +	interrupts = <0 0 4>, <0 1 4>;

SP804 has three interrupt outputs: TIMINT1 (interrupt generated by the
first timer), TIMINT2 (the second timer) and TIMINTC (combined - logical
sum of the two former ones). You may want to describe this somehow to
make the choice possible later (eg. VE has the combined interrupt wired
while - if I understand what Rob is saying correctly - Highbank uses
only the TIMINT1).

> +- reg: Should contain location and length for dual timer register.
> +- clocks: clock driving the dual timer hardware
> +	clocks = <&timclk0 &timclk1>;

Again, there are three "clock" inputs (even ignoring the APBCLK):
TIMCLK, TIMCLKEN1, TIMCLKEN2. The real clocking rate for the timer
depends on the TIMCLK and respective TIMCLKENx - see
http://infocenter.arm.com/help/topic/com.arm.doc.ddi0271d/CJABHCIG.html 

The driver than could make educated choice based on this information.

You may choose to ignore this fact (and require only a clock
representing the effective rate). I did it for the VE DTS, but it still
doesn't seem completely right

> +Optional properties:
> +- arm,sp804-clocksource: Should contain the register offset of TIMER1 or
> +  TIMER2 in Dual Timer Controller.
> +	arm,sp804-clocksource = <0x20>;

You seem to be missing the "arm,sp804-clockevent" one here.

Regards

Pawe?

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 06/11] ARM: vexpress: use clocksource_of_init for sp804
  2013-03-13  5:05 ` [PATCH v3 06/11] ARM: vexpress: " Haojian Zhuang
@ 2013-03-13 11:10   ` Pawel Moll
  2013-03-13 11:42     ` Haojian Zhuang
  0 siblings, 1 reply; 44+ messages in thread
From: Pawel Moll @ 2013-03-13 11:10 UTC (permalink / raw)
  To: linux-arm-kernel

On Wed, 2013-03-13 at 05:05 +0000, Haojian Zhuang wrote:
> Remove all code to parse sp804. Use clocksource_of_init() instead since
> all these code are implemented in sp804 driver already.
> 
> Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
> ---
>  arch/arm/boot/dts/vexpress-v2m-rs1.dtsi |    2 ++
>  arch/arm/boot/dts/vexpress-v2m.dtsi     |    2 ++
>  arch/arm/boot/dts/vexpress-v2p-ca9.dts  |    2 ++
>  arch/arm/mach-vexpress/Kconfig          |    1 +
>  arch/arm/mach-vexpress/v2m.c            |   13 ++-----------
>  5 files changed, 9 insertions(+), 11 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/vexpress-v2m-rs1.dtsi b/arch/arm/boot/dts/vexpress-v2m-rs1.dtsi
> index ac870fb..3fa798f 100644
> --- a/arch/arm/boot/dts/vexpress-v2m-rs1.dtsi
> +++ b/arch/arm/boot/dts/vexpress-v2m-rs1.dtsi
> @@ -183,6 +183,8 @@
>  				interrupts = <2>;
>  				clocks = <&v2m_sysctl 0>, <&v2m_sysctl 1>, <&smbclk>;
>  				clock-names = "timclken1", "timclken2", "apb_pclk";
> +				arm,sp804-clocksource = <0x20>;
> +				arm,sp804-clockevent = <0>;
>  			};
>  
>  			v2m_timer23: timer at 120000 {
> diff --git a/arch/arm/boot/dts/vexpress-v2m.dtsi b/arch/arm/boot/dts/vexpress-v2m.dtsi
> index f142036..86e4046 100644
> --- a/arch/arm/boot/dts/vexpress-v2m.dtsi
> +++ b/arch/arm/boot/dts/vexpress-v2m.dtsi
> @@ -182,6 +182,8 @@
>  				interrupts = <2>;
>  				clocks = <&v2m_sysctl 0>, <&v2m_sysctl 1>, <&smbclk>;
>  				clock-names = "timclken1", "timclken2", "apb_pclk";
> +				arm,sp804-clocksource = <0x20>;
> +				arm,sp804-clockevent = <0>;
>  			};
>  
>  			v2m_timer23: timer at 12000 {
> diff --git a/arch/arm/boot/dts/vexpress-v2p-ca9.dts b/arch/arm/boot/dts/vexpress-v2p-ca9.dts
> index 1420bb1..a2eba95 100644
> --- a/arch/arm/boot/dts/vexpress-v2p-ca9.dts
> +++ b/arch/arm/boot/dts/vexpress-v2p-ca9.dts
> @@ -98,6 +98,8 @@
>  			     <0 49 4>;
>  		clocks = <&oscclk2>, <&oscclk2>;
>  		clock-names = "timclk", "apb_pclk";
> +		arm,sp804-clocksource = <0x20>;
> +		arm,sp804-clockevent = <0>;
>  	};
>  
>  	watchdog at 100e5000 {

I love the possibility of removing the SP804 code from the VE machine
(thanks for your work!), but I'd like to avoid it being replaced by
cryptic properties in the tree.

Now, to get this right: I'm not saying that there should be completly no
OS-specific (but neutral) properties for the clocking system.

I'm saying that in "my" (the VE) case, there are four, effectively
identical timers (each pair sharing an interrupt though). Every single
one of them is perfectly capable of serving as clocksource or
clockevent. Therefore I believe the driver/framework/OS should make its
own decision.

Cheers!

Pawe?

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 03/11] clocksource: sp804: add device tree support
  2013-03-13 11:05   ` Pawel Moll
@ 2013-03-13 11:37     ` Haojian Zhuang
  2013-03-13 11:41       ` Pawel Moll
  2013-03-13 14:17     ` Rob Herring
  1 sibling, 1 reply; 44+ messages in thread
From: Haojian Zhuang @ 2013-03-13 11:37 UTC (permalink / raw)
  To: linux-arm-kernel

On 13 March 2013 19:05, Pawel Moll <pawel.moll@arm.com> wrote:
> On Wed, 2013-03-13 at 05:05 +0000, Haojian Zhuang wrote:
>> +++ b/Documentation/devicetree/bindings/timer/arm,sp804.txt
>> @@ -0,0 +1,27 @@
>> +ARM sp804 Dual Timers
>> +---------------------------------------
>> +
>> +Required properties:
>> +- compatible: Should be "arm,sp804" & "arm,primecell"
>> +- interrupts: Should contain the list of Dual Timer interrupts
>> +     interrupts = <0 0 4>, <0 1 4>;
>
> SP804 has three interrupt outputs: TIMINT1 (interrupt generated by the
> first timer), TIMINT2 (the second timer) and TIMINTC (combined - logical
> sum of the two former ones). You may want to describe this somehow to
> make the choice possible later (eg. VE has the combined interrupt wired
> while - if I understand what Rob is saying correctly - Highbank uses
> only the TIMINT1).
>
I prefer to ignore the TIMINTC. It seems that nobody is using this interrupt.

>> +- reg: Should contain location and length for dual timer register.
>> +- clocks: clock driving the dual timer hardware
>> +     clocks = <&timclk0 &timclk1>;
>
> Again, there are three "clock" inputs (even ignoring the APBCLK):
> TIMCLK, TIMCLKEN1, TIMCLKEN2. The real clocking rate for the timer
> depends on the TIMCLK and respective TIMCLKENx - see
> http://infocenter.arm.com/help/topic/com.arm.doc.ddi0271d/CJABHCIG.html
>
> The driver than could make educated choice based on this information.
>
> You may choose to ignore this fact (and require only a clock
> representing the effective rate). I did it for the VE DTS, but it still
> doesn't seem completely right
>
Sure. I can append it.

>> +Optional properties:
>> +- arm,sp804-clocksource: Should contain the register offset of TIMER1 or
>> +  TIMER2 in Dual Timer Controller.
>> +     arm,sp804-clocksource = <0x20>;
>
> You seem to be missing the "arm,sp804-clockevent" one here.
>
Yes, I missed. I'll update the README.

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 03/11] clocksource: sp804: add device tree support
  2013-03-13 11:37     ` Haojian Zhuang
@ 2013-03-13 11:41       ` Pawel Moll
  0 siblings, 0 replies; 44+ messages in thread
From: Pawel Moll @ 2013-03-13 11:41 UTC (permalink / raw)
  To: linux-arm-kernel

On Wed, 2013-03-13 at 11:37 +0000, Haojian Zhuang wrote:
> On 13 March 2013 19:05, Pawel Moll <pawel.moll@arm.com> wrote:
> > On Wed, 2013-03-13 at 05:05 +0000, Haojian Zhuang wrote:
> >> +++ b/Documentation/devicetree/bindings/timer/arm,sp804.txt
> >> @@ -0,0 +1,27 @@
> >> +ARM sp804 Dual Timers
> >> +---------------------------------------
> >> +
> >> +Required properties:
> >> +- compatible: Should be "arm,sp804" & "arm,primecell"
> >> +- interrupts: Should contain the list of Dual Timer interrupts
> >> +     interrupts = <0 0 4>, <0 1 4>;
> >
> > SP804 has three interrupt outputs: TIMINT1 (interrupt generated by the
> > first timer), TIMINT2 (the second timer) and TIMINTC (combined - logical
> > sum of the two former ones). You may want to describe this somehow to
> > make the choice possible later (eg. VE has the combined interrupt wired
> > while - if I understand what Rob is saying correctly - Highbank uses
> > only the TIMINT1).
> >
> I prefer to ignore the TIMINTC. It seems that nobody is using this interrupt.

VE is the nobody then ;-) As I mentioned above - both VE motherboard
SP804s have the TIMINTC wired up and TIMINT1/TIMINT2 unused.

Pawe?

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 06/11] ARM: vexpress: use clocksource_of_init for sp804
  2013-03-13 11:10   ` Pawel Moll
@ 2013-03-13 11:42     ` Haojian Zhuang
  2013-03-13 11:46       ` Pawel Moll
  0 siblings, 1 reply; 44+ messages in thread
From: Haojian Zhuang @ 2013-03-13 11:42 UTC (permalink / raw)
  To: linux-arm-kernel

On 13 March 2013 19:10, Pawel Moll <pawel.moll@arm.com> wrote:
> On Wed, 2013-03-13 at 05:05 +0000, Haojian Zhuang wrote:
>> Remove all code to parse sp804. Use clocksource_of_init() instead since
>> all these code are implemented in sp804 driver already.
>>
>> Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
>> ---
>>  arch/arm/boot/dts/vexpress-v2m-rs1.dtsi |    2 ++
>>  arch/arm/boot/dts/vexpress-v2m.dtsi     |    2 ++
>>  arch/arm/boot/dts/vexpress-v2p-ca9.dts  |    2 ++
>>  arch/arm/mach-vexpress/Kconfig          |    1 +
>>  arch/arm/mach-vexpress/v2m.c            |   13 ++-----------
>>  5 files changed, 9 insertions(+), 11 deletions(-)
>>
>> diff --git a/arch/arm/boot/dts/vexpress-v2m-rs1.dtsi b/arch/arm/boot/dts/vexpress-v2m-rs1.dtsi
>> index ac870fb..3fa798f 100644
>> --- a/arch/arm/boot/dts/vexpress-v2m-rs1.dtsi
>> +++ b/arch/arm/boot/dts/vexpress-v2m-rs1.dtsi
>> @@ -183,6 +183,8 @@
>>                               interrupts = <2>;
>>                               clocks = <&v2m_sysctl 0>, <&v2m_sysctl 1>, <&smbclk>;
>>                               clock-names = "timclken1", "timclken2", "apb_pclk";
>> +                             arm,sp804-clocksource = <0x20>;
>> +                             arm,sp804-clockevent = <0>;
>>                       };
>>
>>                       v2m_timer23: timer at 120000 {
>> diff --git a/arch/arm/boot/dts/vexpress-v2m.dtsi b/arch/arm/boot/dts/vexpress-v2m.dtsi
>> index f142036..86e4046 100644
>> --- a/arch/arm/boot/dts/vexpress-v2m.dtsi
>> +++ b/arch/arm/boot/dts/vexpress-v2m.dtsi
>> @@ -182,6 +182,8 @@
>>                               interrupts = <2>;
>>                               clocks = <&v2m_sysctl 0>, <&v2m_sysctl 1>, <&smbclk>;
>>                               clock-names = "timclken1", "timclken2", "apb_pclk";
>> +                             arm,sp804-clocksource = <0x20>;
>> +                             arm,sp804-clockevent = <0>;
>>                       };
>>
>>                       v2m_timer23: timer at 12000 {
>> diff --git a/arch/arm/boot/dts/vexpress-v2p-ca9.dts b/arch/arm/boot/dts/vexpress-v2p-ca9.dts
>> index 1420bb1..a2eba95 100644
>> --- a/arch/arm/boot/dts/vexpress-v2p-ca9.dts
>> +++ b/arch/arm/boot/dts/vexpress-v2p-ca9.dts
>> @@ -98,6 +98,8 @@
>>                            <0 49 4>;
>>               clocks = <&oscclk2>, <&oscclk2>;
>>               clock-names = "timclk", "apb_pclk";
>> +             arm,sp804-clocksource = <0x20>;
>> +             arm,sp804-clockevent = <0>;
>>       };
>>
>>       watchdog at 100e5000 {
>
> I love the possibility of removing the SP804 code from the VE machine
> (thanks for your work!), but I'd like to avoid it being replaced by
> cryptic properties in the tree.
>
> Now, to get this right: I'm not saying that there should be completly no
> OS-specific (but neutral) properties for the clocking system.
>
> I'm saying that in "my" (the VE) case, there are four, effectively
> identical timers (each pair sharing an interrupt though). Every single
> one of them is perfectly capable of serving as clocksource or
> clockevent. Therefore I believe the driver/framework/OS should make its
> own decision.
>
I can move those properties into dts file instead.

If clocksource uses alias to configure source or event. There's still a lot
of work. At least we need to split dual timer into two timer devices in DTS.

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 06/11] ARM: vexpress: use clocksource_of_init for sp804
  2013-03-13 11:42     ` Haojian Zhuang
@ 2013-03-13 11:46       ` Pawel Moll
  2013-03-13 12:21         ` Haojian Zhuang
  0 siblings, 1 reply; 44+ messages in thread
From: Pawel Moll @ 2013-03-13 11:46 UTC (permalink / raw)
  To: linux-arm-kernel

On Wed, 2013-03-13 at 11:42 +0000, Haojian Zhuang wrote:
> > I love the possibility of removing the SP804 code from the VE machine
> > (thanks for your work!), but I'd like to avoid it being replaced by
> > cryptic properties in the tree.
> >
> > Now, to get this right: I'm not saying that there should be completly no
> > OS-specific (but neutral) properties for the clocking system.
> >
> > I'm saying that in "my" (the VE) case, there are four, effectively
> > identical timers (each pair sharing an interrupt though). Every single
> > one of them is perfectly capable of serving as clocksource or
> > clockevent. Therefore I believe the driver/framework/OS should make its
> > own decision.
> >
> I can move those properties into dts file instead.

I'm not sure I understand you here...

> If clocksource uses alias to configure source or event. There's still a lot
> of work. At least we need to split dual timer into two timer devices in DTS.

My point is: at least for VE there is _no need_ for any alias or special
property in the tree (DTS). All timers are equal. The system can (and
should) pick any one it wants.

Pawe?

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 06/11] ARM: vexpress: use clocksource_of_init for sp804
  2013-03-13 11:46       ` Pawel Moll
@ 2013-03-13 12:21         ` Haojian Zhuang
  2013-03-13 14:48           ` Pawel Moll
  0 siblings, 1 reply; 44+ messages in thread
From: Haojian Zhuang @ 2013-03-13 12:21 UTC (permalink / raw)
  To: linux-arm-kernel

On 13 March 2013 19:46, Pawel Moll <pawel.moll@arm.com> wrote:
> On Wed, 2013-03-13 at 11:42 +0000, Haojian Zhuang wrote:
>> > I love the possibility of removing the SP804 code from the VE machine
>> > (thanks for your work!), but I'd like to avoid it being replaced by
>> > cryptic properties in the tree.
>> >
>> > Now, to get this right: I'm not saying that there should be completly no
>> > OS-specific (but neutral) properties for the clocking system.
>> >
>> > I'm saying that in "my" (the VE) case, there are four, effectively
>> > identical timers (each pair sharing an interrupt though). Every single
>> > one of them is perfectly capable of serving as clocksource or
>> > clockevent. Therefore I believe the driver/framework/OS should make its
>> > own decision.
>> >
>> I can move those properties into dts file instead.
>
> I'm not sure I understand you here...
>
>> If clocksource uses alias to configure source or event. There's still a lot
>> of work. At least we need to split dual timer into two timer devices in DTS.
>
> My point is: at least for VE there is _no need_ for any alias or special
> property in the tree (DTS). All timers are equal. The system can (and
> should) pick any one it wants.
>
> Pawe?
>
Do you mean that system wants to pick any one randomly? It's impossible.
Imagine that only TIMINT1 signal in sp804 is routed to interrupt controller.
Could system still pick any one it wants?

I think that clocksource or clockevent must be specified in DTS. Whatever
we're using alias or property.

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 03/11] clocksource: sp804: add device tree support
  2013-03-13 11:05   ` Pawel Moll
  2013-03-13 11:37     ` Haojian Zhuang
@ 2013-03-13 14:17     ` Rob Herring
  2013-03-13 14:42       ` Pawel Moll
  2013-03-15 12:20       ` Russell King - ARM Linux
  1 sibling, 2 replies; 44+ messages in thread
From: Rob Herring @ 2013-03-13 14:17 UTC (permalink / raw)
  To: linux-arm-kernel

On 03/13/2013 06:05 AM, Pawel Moll wrote:
> On Wed, 2013-03-13 at 05:05 +0000, Haojian Zhuang wrote:
>> +++ b/Documentation/devicetree/bindings/timer/arm,sp804.txt
>> @@ -0,0 +1,27 @@
>> +ARM sp804 Dual Timers
>> +---------------------------------------
>> +
>> +Required properties:
>> +- compatible: Should be "arm,sp804" & "arm,primecell"
>> +- interrupts: Should contain the list of Dual Timer interrupts
>> +	interrupts = <0 0 4>, <0 1 4>;
> 
> SP804 has three interrupt outputs: TIMINT1 (interrupt generated by the
> first timer), TIMINT2 (the second timer) and TIMINTC (combined - logical
> sum of the two former ones). You may want to describe this somehow to
> make the choice possible later (eg. VE has the combined interrupt wired
> while - if I understand what Rob is saying correctly - Highbank uses
> only the TIMINT1).

How about:

1 irq - TIMINT1
2 irqs w/ same source # - TIMINTC
2 irqs w/ different source # - TIMINT1 and TIMINT2

I'm not completely sure if Linux and the irq domain code handles the
same interrupt source repeated. It should because that is basically a
shared irq line.

If we ever see only TIMINT2 connected we can add a property for that,
but I think that case is unlikely.

> 
>> +- reg: Should contain location and length for dual timer register.
>> +- clocks: clock driving the dual timer hardware
>> +	clocks = <&timclk0 &timclk1>;
> 
> Again, there are three "clock" inputs (even ignoring the APBCLK):

We should not ignore that clock as we may want this to be a proper
amba_device someday.

> TIMCLK, TIMCLKEN1, TIMCLKEN2. The real clocking rate for the timer
> depends on the TIMCLK and respective TIMCLKENx - see
> http://infocenter.arm.com/help/topic/com.arm.doc.ddi0271d/CJABHCIG.html 
> 
> The driver than could make educated choice based on this information.
> 
> You may choose to ignore this fact (and require only a clock
> representing the effective rate). I did it for the VE DTS, but it still
> doesn't seem completely right
> 
>> +Optional properties:
>> +- arm,sp804-clocksource: Should contain the register offset of TIMER1 or
>> +  TIMER2 in Dual Timer Controller.
>> +	arm,sp804-clocksource = <0x20>;
> 
> You seem to be missing the "arm,sp804-clockevent" one here.

These should stay as aliases or go away as I suggested.

Rob

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 03/11] clocksource: sp804: add device tree support
  2013-03-13 14:17     ` Rob Herring
@ 2013-03-13 14:42       ` Pawel Moll
  2013-03-13 14:51         ` Rob Herring
  2013-03-15 12:20       ` Russell King - ARM Linux
  1 sibling, 1 reply; 44+ messages in thread
From: Pawel Moll @ 2013-03-13 14:42 UTC (permalink / raw)
  To: linux-arm-kernel

On Wed, 2013-03-13 at 14:17 +0000, Rob Herring wrote:
> How about:
> 
> 1 irq - TIMINT1
> 2 irqs w/ same source # - TIMINTC
> 2 irqs w/ different source # - TIMINT1 and TIMINT2
> 
> I'm not completely sure if Linux and the irq domain code handles the
> same interrupt source repeated. It should because that is basically a
> shared irq line.
> 
> If we ever see only TIMINT2 connected we can add a property for that,
> but I think that case is unlikely.

I was rather thinking about using the "interrupt-names" property and
naming them explicitly, eg:

	interrupt-names = "timint1", "timint2";
	interrupts = <1>, <2>;

	interrupt-names = "timint1";
	interrupts = <1>;

	interrupt-names = "timint2";
	interrupts = <2>;

	interrupt-names = "timintc";
	interrupts = <3>;

But now I see that of_amba_device_create() doesn't do anything about it
(platform device would use them as resource name so we could use
platform_get_resource_byname), so I'm not sure any more...

> > 
> >> +- reg: Should contain location and length for dual timer register.
> >> +- clocks: clock driving the dual timer hardware
> >> +	clocks = <&timclk0 &timclk1>;
> > 
> > Again, there are three "clock" inputs (even ignoring the APBCLK):
> 
> We should not ignore that clock as we may want this to be a proper
> amba_device someday.

Sorry, wrong wording. I meant to say "even not mentioning the
APBCLK" (because it's required anyway by the primecell binding). VE
SP804 node obviously has it defined:

v2m_timer01: timer at 110000 {                           
	compatible = "arm,sp804", "arm,primecell";    
	reg = <0x110000 0x1000>;
	interrupts = <2>;                
	clocks = <&v2m_sysctl 0>, <&v2m_sysctl 1>, <&smbclk>;
	clock-names = "timclken1", "timclken2", "apb_pclk";
};                                   

> > TIMCLK, TIMCLKEN1, TIMCLKEN2. The real clocking rate for the timer
> > depends on the TIMCLK and respective TIMCLKENx - see
> > http://infocenter.arm.com/help/topic/com.arm.doc.ddi0271d/CJABHCIG.html 
> > 
> > The driver than could make educated choice based on this information.
> > 
> > You may choose to ignore this fact (and require only a clock
> > representing the effective rate). I did it for the VE DTS, but it still
> > doesn't seem completely right
> > 
> >> +Optional properties:
> >> +- arm,sp804-clocksource: Should contain the register offset of TIMER1 or
> >> +  TIMER2 in Dual Timer Controller.
> >> +	arm,sp804-clocksource = <0x20>;
> > 
> > You seem to be missing the "arm,sp804-clockevent" one here.
> 
> These should stay as aliases or go away as I suggested.

I merely pointed out that it's missing from the binding description.

I couldn't agree more that both should not be there in the first place.

Pawe?

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 06/11] ARM: vexpress: use clocksource_of_init for sp804
  2013-03-13 12:21         ` Haojian Zhuang
@ 2013-03-13 14:48           ` Pawel Moll
  2013-03-13 15:01             ` Haojian Zhuang
  0 siblings, 1 reply; 44+ messages in thread
From: Pawel Moll @ 2013-03-13 14:48 UTC (permalink / raw)
  To: linux-arm-kernel

On Wed, 2013-03-13 at 12:21 +0000, Haojian Zhuang wrote:
> Do you mean that system wants to pick any one randomly? It's impossible.

It is possible in case of the VE platform. Therefore it is not
completely impossible. QED :-)

> Imagine that only TIMINT1 signal in sp804 is routed to interrupt controller.
> Could system still pick any one it wants?

If you tell the system that only TIMINT1 is wired, it shouldn't even try
to use the second timer for anything that would require the interrupt.
Therefore, describing the hardware sufficiently, you're giving the
system enough information to make the right decisions.

> I think that clocksource or clockevent must be specified in DTS. Whatever
> we're using alias or property.

I'm convinced it does not *must* be there. I think it *can* be there,
for platforms where the available timers are not equal (for whatever
reason). My point is: why are you trying to force me to put some
information into my hardware description which doesn't have any meaning
for me?

Pawe?

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 03/11] clocksource: sp804: add device tree support
  2013-03-13 14:42       ` Pawel Moll
@ 2013-03-13 14:51         ` Rob Herring
  2013-03-13 14:55           ` Pawel Moll
  0 siblings, 1 reply; 44+ messages in thread
From: Rob Herring @ 2013-03-13 14:51 UTC (permalink / raw)
  To: linux-arm-kernel

On 03/13/2013 09:42 AM, Pawel Moll wrote:
> On Wed, 2013-03-13 at 14:17 +0000, Rob Herring wrote:
>> How about:
>>
>> 1 irq - TIMINT1
>> 2 irqs w/ same source # - TIMINTC
>> 2 irqs w/ different source # - TIMINT1 and TIMINT2
>>
>> I'm not completely sure if Linux and the irq domain code handles the
>> same interrupt source repeated. It should because that is basically a
>> shared irq line.
>>
>> If we ever see only TIMINT2 connected we can add a property for that,
>> but I think that case is unlikely.
> 
> I was rather thinking about using the "interrupt-names" property and
> naming them explicitly, eg:
> 
> 	interrupt-names = "timint1", "timint2";
> 	interrupts = <1>, <2>;
> 
> 	interrupt-names = "timint1";
> 	interrupts = <1>;
> 
> 	interrupt-names = "timint2";
> 	interrupts = <2>;
> 
> 	interrupt-names = "timintc";
> 	interrupts = <3>;
> 
> But now I see that of_amba_device_create() doesn't do anything about it
> (platform device would use them as resource name so we could use
> platform_get_resource_byname), so I'm not sure any more...

The interrupt-names property should not be required and without it here
you cannot determine the configuration.

Rob

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 03/11] clocksource: sp804: add device tree support
  2013-03-13 14:51         ` Rob Herring
@ 2013-03-13 14:55           ` Pawel Moll
  2013-03-13 15:11             ` Haojian Zhuang
  0 siblings, 1 reply; 44+ messages in thread
From: Pawel Moll @ 2013-03-13 14:55 UTC (permalink / raw)
  To: linux-arm-kernel

On Wed, 2013-03-13 at 14:51 +0000, Rob Herring wrote:
> On 03/13/2013 09:42 AM, Pawel Moll wrote:
> > On Wed, 2013-03-13 at 14:17 +0000, Rob Herring wrote:
> >> How about:
> >>
> >> 1 irq - TIMINT1
> >> 2 irqs w/ same source # - TIMINTC
> >> 2 irqs w/ different source # - TIMINT1 and TIMINT2
> >>
> >> I'm not completely sure if Linux and the irq domain code handles the
> >> same interrupt source repeated. It should because that is basically a
> >> shared irq line.
> >>
> >> If we ever see only TIMINT2 connected we can add a property for that,
> >> but I think that case is unlikely.
> > 
> > I was rather thinking about using the "interrupt-names" property and
> > naming them explicitly, eg:
> > 
> > 	interrupt-names = "timint1", "timint2";
> > 	interrupts = <1>, <2>;
> > 
> > 	interrupt-names = "timint1";
> > 	interrupts = <1>;
> > 
> > 	interrupt-names = "timint2";
> > 	interrupts = <2>;
> > 
> > 	interrupt-names = "timintc";
> > 	interrupts = <3>;
> > 
> > But now I see that of_amba_device_create() doesn't do anything about it
> > (platform device would use them as resource name so we could use
> > platform_get_resource_byname), so I'm not sure any more...
> 
> The interrupt-names property should not be required and without it here
> you cannot determine the configuration.

It is not required by the standard interrupt bindings. But it could be
required by the SP804 binding, couldn't it? (like any other property)
"Encoding" the information by specific organization of the field makes
it "invisible to the naked eye".

Not that I have any strong feelings about it.

Pawe?

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 06/11] ARM: vexpress: use clocksource_of_init for sp804
  2013-03-13 14:48           ` Pawel Moll
@ 2013-03-13 15:01             ` Haojian Zhuang
  2013-03-13 15:19               ` Pawel Moll
  0 siblings, 1 reply; 44+ messages in thread
From: Haojian Zhuang @ 2013-03-13 15:01 UTC (permalink / raw)
  To: linux-arm-kernel

On 13 March 2013 22:48, Pawel Moll <pawel.moll@arm.com> wrote:
> On Wed, 2013-03-13 at 12:21 +0000, Haojian Zhuang wrote:
>> Do you mean that system wants to pick any one randomly? It's impossible.
>
> It is possible in case of the VE platform. Therefore it is not
> completely impossible. QED :-)
>
Yes, it's possible. Since only clocksource / clockevent is using SP804 timer
on the VE platform. If user app or something else is using other SP804
timer, it would be mess because of resource conflict.

>> Imagine that only TIMINT1 signal in sp804 is routed to interrupt controller.
>> Could system still pick any one it wants?
>
Then we need another new property. I try to find using minim properties.

> If you tell the system that only TIMINT1 is wired, it shouldn't even try
> to use the second timer for anything that would require the interrupt.
> Therefore, describing the hardware sufficiently, you're giving the
> system enough information to make the right decisions.
>
>> I think that clocksource or clockevent must be specified in DTS. Whatever
>> we're using alias or property.
>
> I'm convinced it does not *must* be there. I think it *can* be there,
> for platforms where the available timers are not equal (for whatever
> reason). My point is: why are you trying to force me to put some
> information into my hardware description which doesn't have any meaning
> for me?
>
As I mentioned above, system must know the behavior first. The upper layer
software could know which timer is used in clocksource or clockevent.

For example, your Android system could be shared on multiple platforms. It
could parse hardware information from DTS. (Of course, it hasn't this feature
yet). Then it could arrange apps to use other timers.

It's like you define console on specified UART even you have multiples UART
port.

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 03/11] clocksource: sp804: add device tree support
  2013-03-13 14:55           ` Pawel Moll
@ 2013-03-13 15:11             ` Haojian Zhuang
  2013-03-13 15:23               ` Pawel Moll
  0 siblings, 1 reply; 44+ messages in thread
From: Haojian Zhuang @ 2013-03-13 15:11 UTC (permalink / raw)
  To: linux-arm-kernel

On 13 March 2013 22:55, Pawel Moll <pawel.moll@arm.com> wrote:
> On Wed, 2013-03-13 at 14:51 +0000, Rob Herring wrote:
>> On 03/13/2013 09:42 AM, Pawel Moll wrote:
>> > On Wed, 2013-03-13 at 14:17 +0000, Rob Herring wrote:
>> >> How about:
>> >>
>> >> 1 irq - TIMINT1
>> >> 2 irqs w/ same source # - TIMINTC
>> >> 2 irqs w/ different source # - TIMINT1 and TIMINT2
>> >>
>> >> I'm not completely sure if Linux and the irq domain code handles the
>> >> same interrupt source repeated. It should because that is basically a
>> >> shared irq line.
>> >>
>> >> If we ever see only TIMINT2 connected we can add a property for that,
>> >> but I think that case is unlikely.
>> >
>> > I was rather thinking about using the "interrupt-names" property and
>> > naming them explicitly, eg:
>> >
>> >     interrupt-names = "timint1", "timint2";
>> >     interrupts = <1>, <2>;
>> >
>> >     interrupt-names = "timint1";
>> >     interrupts = <1>;
>> >
>> >     interrupt-names = "timint2";
>> >     interrupts = <2>;
>> >
>> >     interrupt-names = "timintc";
>> >     interrupts = <3>;
>> >
>> > But now I see that of_amba_device_create() doesn't do anything about it
>> > (platform device would use them as resource name so we could use
>> > platform_get_resource_byname), so I'm not sure any more...
>>
>> The interrupt-names property should not be required and without it here
>> you cannot determine the configuration.
>
> It is not required by the standard interrupt bindings. But it could be
> required by the SP804 binding, couldn't it? (like any other property)
> "Encoding" the information by specific organization of the field makes
> it "invisible to the naked eye".
>
> Not that I have any strong feelings about it.
>
> Pawe?
>
>

What's the scenario that we must use TIMINTC? TIMINT1 & TIMINT2 are
already enough on these two TIMERs. If we really needn't TIMINTC, we
need to support it. Since it's over-designed.

If TIMINT1 & TIMINT2 aren't routed, and only TIMINTC is routed. It's another
case. We can consider it as replacement of TIMINT1.

Regards
Haojian

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 06/11] ARM: vexpress: use clocksource_of_init for sp804
  2013-03-13 15:01             ` Haojian Zhuang
@ 2013-03-13 15:19               ` Pawel Moll
  2013-03-13 15:59                 ` Haojian Zhuang
  0 siblings, 1 reply; 44+ messages in thread
From: Pawel Moll @ 2013-03-13 15:19 UTC (permalink / raw)
  To: linux-arm-kernel

On Wed, 2013-03-13 at 15:01 +0000, Haojian Zhuang wrote:
> Yes, it's possible. Since only clocksource / clockevent is using SP804 timer
> on the VE platform. If user app or something else is using other SP804
> timer, it would be mess because of resource conflict.

How would you expose this device to the app or something else? It's an
amba_bus device, so it must be bound with an amba_driver. Otherwise
you're abusing the device model and, well, you're on your own.

The devices are managed by the system. The device tree is merely a
description of the available hardware.

> >> Imagine that only TIMINT1 signal in sp804 is routed to interrupt controller.
> >> Could system still pick any one it wants?
> >
> Then we need another new property. I try to find using minim properties.

No, we don't. See the discussion with Rob. He has an idea (using the
interrupt property only), I have another one (using already defined
interrupt-names property). I see you've just came with another one
(TIMINTC treated as TIMINT1), which is fine with me. Either way you've
got what you need to make the right decision.

> As I mentioned above, system must know the behavior first. The upper layer
> software could know which timer is used in clocksource or clockevent.

I claim otherwise. The upper layer software should know what does the
hardware offer and based on this knowledge use it in a way it wants to.

> For example, your Android system could be shared on multiple platforms. It
> could parse hardware information from DTS. (Of course, it hasn't this feature
> yet). Then it could arrange apps to use other timers.

I honestly don't know what are you suggesting here other than it looks
like an abuse to the device model.

> It's like you define console on specified UART even you have multiples UART
> port.

Where do you do this? In the Device Tree? No. In the kernel command
line, which is a runtime argument (the fact it is actually being passed
through the tree is irrelevant here) You have the serialX aliases, which
- again - simply describe the hardware ("this node is connected to a
connector labeled as serial X"). The tree doesn't tell that the user
connected his serial cable to serial1 so it should be used as the
console.

Pawe?

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 03/11] clocksource: sp804: add device tree support
  2013-03-13 15:11             ` Haojian Zhuang
@ 2013-03-13 15:23               ` Pawel Moll
  2013-03-13 15:25                 ` Haojian Zhuang
  0 siblings, 1 reply; 44+ messages in thread
From: Pawel Moll @ 2013-03-13 15:23 UTC (permalink / raw)
  To: linux-arm-kernel

On Wed, 2013-03-13 at 14:17 +0000, Rob Herring wrote:
> How about:
> 
> 1 irq - TIMINT1
> 2 irqs w/ same source # - TIMINTC
> 2 irqs w/ different source # - TIMINT1 and TIMINT2

On Wed, 2013-03-13 at 15:11 +0000, Haojian Zhuang wrote:
> What's the scenario that we must use TIMINTC? TIMINT1 & TIMINT2 are
> already enough on these two TIMERs. If we really needn't TIMINTC, we
> need to support it. Since it's over-designed.
> 
> If TIMINT1 & TIMINT2 aren't routed, and only TIMINTC is routed. It's another
> case. We can consider it as replacement of TIMINT1.

Just a thought... How to describe a SP804 with only TIMINT2 wired up?

Pawe?

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 03/11] clocksource: sp804: add device tree support
  2013-03-13 15:23               ` Pawel Moll
@ 2013-03-13 15:25                 ` Haojian Zhuang
  2013-03-13 15:29                   ` Pawel Moll
  0 siblings, 1 reply; 44+ messages in thread
From: Haojian Zhuang @ 2013-03-13 15:25 UTC (permalink / raw)
  To: linux-arm-kernel

On 13 March 2013 23:23, Pawel Moll <pawel.moll@arm.com> wrote:
> On Wed, 2013-03-13 at 14:17 +0000, Rob Herring wrote:
>> How about:
>>
>> 1 irq - TIMINT1
>> 2 irqs w/ same source # - TIMINTC
>> 2 irqs w/ different source # - TIMINT1 and TIMINT2
>
> On Wed, 2013-03-13 at 15:11 +0000, Haojian Zhuang wrote:
>> What's the scenario that we must use TIMINTC? TIMINT1 & TIMINT2 are
>> already enough on these two TIMERs. If we really needn't TIMINTC, we
>> need to support it. Since it's over-designed.
>>
>> If TIMINT1 & TIMINT2 aren't routed, and only TIMINTC is routed. It's another
>> case. We can consider it as replacement of TIMINT1.
>
> Just a thought... How to describe a SP804 with only TIMINT2 wired up?
>
> Pawe?
>
>
There's no difference on TIMINTC is only used to replace TIMINT1 or TIMINT2.
We only need to tell sp804 driver which timer is using irq, and the irq number.

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 03/11] clocksource: sp804: add device tree support
  2013-03-13 15:25                 ` Haojian Zhuang
@ 2013-03-13 15:29                   ` Pawel Moll
  2013-03-13 15:39                     ` Rob Herring
  2013-03-13 15:42                     ` Haojian Zhuang
  0 siblings, 2 replies; 44+ messages in thread
From: Pawel Moll @ 2013-03-13 15:29 UTC (permalink / raw)
  To: linux-arm-kernel

On Wed, 2013-03-13 at 15:25 +0000, Haojian Zhuang wrote:
> On 13 March 2013 23:23, Pawel Moll <pawel.moll@arm.com> wrote:
> > On Wed, 2013-03-13 at 14:17 +0000, Rob Herring wrote:
> >> How about:
> >>
> >> 1 irq - TIMINT1
> >> 2 irqs w/ same source # - TIMINTC
> >> 2 irqs w/ different source # - TIMINT1 and TIMINT2
> >
> > On Wed, 2013-03-13 at 15:11 +0000, Haojian Zhuang wrote:
> >> What's the scenario that we must use TIMINTC? TIMINT1 & TIMINT2 are
> >> already enough on these two TIMERs. If we really needn't TIMINTC, we
> >> need to support it. Since it's over-designed.
> >>
> >> If TIMINT1 & TIMINT2 aren't routed, and only TIMINTC is routed. It's another
> >> case. We can consider it as replacement of TIMINT1.
> >
> > Just a thought... How to describe a SP804 with only TIMINT2 wired up?
> >
> > Pawe?
> >
> >
> There's no difference on TIMINTC is only used to replace TIMINT1 or TIMINT2.
> We only need to tell sp804 driver which timer is using irq, and the irq number.

If I understand you well:

* Both TIMINT1 and TIMINT2 wired up - TIMINTC doesn't matter

	interrupts = <1>, <2>;

* TIMINT1 wired up, TIMINT2 not wired up

	interrupts = <1>;

* Only TIMINTC wired up - treat it as TIMINT1

	interrupts = <1>;

So far so good. My question is, how do you describe the following:

* _Only_ TIMINT2 wired up, TIMINT1 and TIMINTC _not_ wired up

	interrupts = ???

Pawe?

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 03/11] clocksource: sp804: add device tree support
  2013-03-13 15:29                   ` Pawel Moll
@ 2013-03-13 15:39                     ` Rob Herring
  2013-03-13 15:41                       ` Pawel Moll
  2013-03-13 15:42                     ` Haojian Zhuang
  1 sibling, 1 reply; 44+ messages in thread
From: Rob Herring @ 2013-03-13 15:39 UTC (permalink / raw)
  To: linux-arm-kernel

On 03/13/2013 10:29 AM, Pawel Moll wrote:
> On Wed, 2013-03-13 at 15:25 +0000, Haojian Zhuang wrote:
>> On 13 March 2013 23:23, Pawel Moll <pawel.moll@arm.com> wrote:
>>> On Wed, 2013-03-13 at 14:17 +0000, Rob Herring wrote:
>>>> How about:
>>>>
>>>> 1 irq - TIMINT1
>>>> 2 irqs w/ same source # - TIMINTC
>>>> 2 irqs w/ different source # - TIMINT1 and TIMINT2
>>>
>>> On Wed, 2013-03-13 at 15:11 +0000, Haojian Zhuang wrote:
>>>> What's the scenario that we must use TIMINTC? TIMINT1 & TIMINT2 are
>>>> already enough on these two TIMERs. If we really needn't TIMINTC, we
>>>> need to support it. Since it's over-designed.
>>>>
>>>> If TIMINT1 & TIMINT2 aren't routed, and only TIMINTC is routed. It's another
>>>> case. We can consider it as replacement of TIMINT1.
>>>
>>> Just a thought... How to describe a SP804 with only TIMINT2 wired up?
>>>
>>> Pawe?
>>>
>>>
>> There's no difference on TIMINTC is only used to replace TIMINT1 or TIMINT2.
>> We only need to tell sp804 driver which timer is using irq, and the irq number.
> 
> If I understand you well:
> 
> * Both TIMINT1 and TIMINT2 wired up - TIMINTC doesn't matter
> 
> 	interrupts = <1>, <2>;
> 
> * TIMINT1 wired up, TIMINT2 not wired up
> 
> 	interrupts = <1>;
> 
> * Only TIMINTC wired up - treat it as TIMINT1
> 
> 	interrupts = <1>;
> 
> So far so good. My question is, how do you describe the following:
> 
> * _Only_ TIMINT2 wired up, TIMINT1 and TIMINTC _not_ wired up
> 
> 	interrupts = ???

I previously described that to add a property in that case. That makes
INT1 and INT2 only handling asymetric though. An alternative would be an
optional property "arm,sp804-has-irq = <#>" in the case of only INT1 or
INT2 connected. The combined irq would be a single irq without the
"arm,sp804-has-irq" property and both connected would be 2 irqs.

Rob

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 03/11] clocksource: sp804: add device tree support
  2013-03-13 15:39                     ` Rob Herring
@ 2013-03-13 15:41                       ` Pawel Moll
  2013-03-13 15:44                         ` Haojian Zhuang
  0 siblings, 1 reply; 44+ messages in thread
From: Pawel Moll @ 2013-03-13 15:41 UTC (permalink / raw)
  To: linux-arm-kernel

On Wed, 2013-03-13 at 15:39 +0000, Rob Herring wrote:
> I previously described that to add a property in that case. That makes
> INT1 and INT2 only handling asymetric though. An alternative would be an
> optional property "arm,sp804-has-irq = <#>" in the case of only INT1 or
> INT2 connected. The combined irq would be a single irq without the
> "arm,sp804-has-irq" property and both connected would be 2 irqs.

Fine with me.

Pawe?

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 03/11] clocksource: sp804: add device tree support
  2013-03-13 15:29                   ` Pawel Moll
  2013-03-13 15:39                     ` Rob Herring
@ 2013-03-13 15:42                     ` Haojian Zhuang
  2013-03-13 15:49                       ` Pawel Moll
  1 sibling, 1 reply; 44+ messages in thread
From: Haojian Zhuang @ 2013-03-13 15:42 UTC (permalink / raw)
  To: linux-arm-kernel

On 13 March 2013 23:29, Pawel Moll <pawel.moll@arm.com> wrote:
> On Wed, 2013-03-13 at 15:25 +0000, Haojian Zhuang wrote:
>> On 13 March 2013 23:23, Pawel Moll <pawel.moll@arm.com> wrote:
>> > On Wed, 2013-03-13 at 14:17 +0000, Rob Herring wrote:
>> >> How about:
>> >>
>> >> 1 irq - TIMINT1
>> >> 2 irqs w/ same source # - TIMINTC
>> >> 2 irqs w/ different source # - TIMINT1 and TIMINT2
>> >
>> > On Wed, 2013-03-13 at 15:11 +0000, Haojian Zhuang wrote:
>> >> What's the scenario that we must use TIMINTC? TIMINT1 & TIMINT2 are
>> >> already enough on these two TIMERs. If we really needn't TIMINTC, we
>> >> need to support it. Since it's over-designed.
>> >>
>> >> If TIMINT1 & TIMINT2 aren't routed, and only TIMINTC is routed. It's another
>> >> case. We can consider it as replacement of TIMINT1.
>> >
>> > Just a thought... How to describe a SP804 with only TIMINT2 wired up?
>> >
>> > Pawe?
>> >
>> >
>> There's no difference on TIMINTC is only used to replace TIMINT1 or TIMINT2.
>> We only need to tell sp804 driver which timer is using irq, and the irq number.
>
> If I understand you well:
>
> * Both TIMINT1 and TIMINT2 wired up - TIMINTC doesn't matter
>
>         interrupts = <1>, <2>;
>
> * TIMINT1 wired up, TIMINT2 not wired up
>
>         interrupts = <1>;
>
> * Only TIMINTC wired up - treat it as TIMINT1
>
>         interrupts = <1>;
>
> So far so good. My question is, how do you describe the following:
>
> * _Only_ TIMINT2 wired up, TIMINT1 and TIMINTC _not_ wired up
>
>         interrupts = ???
>
> Pawe?
>
>
>
In my current implementation, I need two things to judge whether
irq is really necessary.

If the timer contains "arm,sp804-clockevent = <evtoffs>" property,
I'll check whether the timer irq is specified at the same time.

TIMINT1 & TIMINTC are not routed. TIMINT2 is used for clock event.

     interrupts = <any number> <1>;

        if (!retevt) {
                if (evtoffs) {
                        /* TIMER2 is clock event */
                        i = 1;
                        evtoffs = TIMER_2_BASE;
                } else {
                        /* TIMER1 is clock event */
                        i = 0;
                        evtoffs = TIMER_1_BASE;
                }
                irq = irq_of_parse_and_map(np, i);
                ...
        }

If the timer contains "arm,sp804-clocksource = <srcoffs>" property,
I won't check the timer irq. You even needn't define it.

TIMINT1 & TIMINTC are not routed. TIMER2 is used for clock source.
      interrupts = <any number> <any number>;
or
      don't define interrupts

        if (!retsrc) {
                if (srcoffs) {
                        /* TIMER2 is clock source */
                        i = 1;
                        srcoffs = TIMER_2_BASE;
                } else {
                        /* TIMER1 is clock source */
                        i = 0;
                        srcoffs = TIMER_1_BASE;
                }
                ...
        }

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 03/11] clocksource: sp804: add device tree support
  2013-03-13 15:41                       ` Pawel Moll
@ 2013-03-13 15:44                         ` Haojian Zhuang
  0 siblings, 0 replies; 44+ messages in thread
From: Haojian Zhuang @ 2013-03-13 15:44 UTC (permalink / raw)
  To: linux-arm-kernel

On 13 March 2013 23:41, Pawel Moll <pawel.moll@arm.com> wrote:
> On Wed, 2013-03-13 at 15:39 +0000, Rob Herring wrote:
>> I previously described that to add a property in that case. That makes
>> INT1 and INT2 only handling asymetric though. An alternative would be an
>> optional property "arm,sp804-has-irq = <#>" in the case of only INT1 or
>> INT2 connected. The combined irq would be a single irq without the
>> "arm,sp804-has-irq" property and both connected would be 2 irqs.
>
> Fine with me.
>
> Pawe?
>
>

It's OK to me. I can use this property instead.

Regards
Haojian

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 03/11] clocksource: sp804: add device tree support
  2013-03-13 15:42                     ` Haojian Zhuang
@ 2013-03-13 15:49                       ` Pawel Moll
  2013-03-13 16:35                         ` Arnd Bergmann
  0 siblings, 1 reply; 44+ messages in thread
From: Pawel Moll @ 2013-03-13 15:49 UTC (permalink / raw)
  To: linux-arm-kernel

On Wed, 2013-03-13 at 15:42 +0000, Haojian Zhuang wrote:
> In my current implementation, I need two things to judge whether
> irq is really necessary.
> 
> If the timer contains "arm,sp804-clockevent = <evtoffs>" property,
> I'll check whether the timer irq is specified at the same time.
> 
> TIMINT1 & TIMINTC are not routed. TIMINT2 is used for clock event.

Fine, so simply reverse the logic and drop the "arm,sp804-clock*"
properties. Something like:

if (has_timint1) {
	evtoffs = TIMER_1_BASE;
	irq = irq_of_parse_and_map(np, 1);
	srcoffs = TIMER_2_BASE;
} else (has_timint2) {
	evtoffs = TIMER_2_BASE;
	irq = irq_of_parse_and_map(np, 2);
	srcoffs = TIMER_1_BASE;
} else {
	can't be clockevent, sorry
}

Hope it makes clear what I'd expect from the driver.

Pawe?

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 06/11] ARM: vexpress: use clocksource_of_init for sp804
  2013-03-13 15:19               ` Pawel Moll
@ 2013-03-13 15:59                 ` Haojian Zhuang
  2013-03-13 16:28                   ` Pawel Moll
  2013-03-13 16:32                   ` Rob Herring
  0 siblings, 2 replies; 44+ messages in thread
From: Haojian Zhuang @ 2013-03-13 15:59 UTC (permalink / raw)
  To: linux-arm-kernel

On 13 March 2013 23:19, Pawel Moll <pawel.moll@arm.com> wrote:
> On Wed, 2013-03-13 at 15:01 +0000, Haojian Zhuang wrote:
>> Yes, it's possible. Since only clocksource / clockevent is using SP804 timer
>> on the VE platform. If user app or something else is using other SP804
>> timer, it would be mess because of resource conflict.
>
> How would you expose this device to the app or something else? It's an
> amba_bus device, so it must be bound with an amba_driver. Otherwise
> you're abusing the device model and, well, you're on your own.
>
> The devices are managed by the system. The device tree is merely a
> description of the available hardware.
>
Maybe I didn't express my idea well. My point is that timer could be
clock source
/clock event. It could also just be a timer that user app or other device driver
may want to use it directly. There're a lot of reason that user app or some
 driver wants to use hardware timer. For example, the specific timer may
keep running even system is in low power mode.

Although there's so much hardware timers available, system must choose
one for the usage of clock source / clock event / other hardware timer usage.

>> >> Imagine that only TIMINT1 signal in sp804 is routed to interrupt controller.
>> >> Could system still pick any one it wants?
>> >
>> Then we need another new property. I try to find using minim properties.
>
> No, we don't. See the discussion with Rob. He has an idea (using the
> interrupt property only), I have another one (using already defined
> interrupt-names property). I see you've just came with another one
> (TIMINTC treated as TIMINT1), which is fine with me. Either way you've
> got what you need to make the right decision.
>
After considered as second time, I think that we still need a property to meet
alias usage. Excuse me expand it in this topic.

arm,sp804-has-irq = <offset>;
The offset means TIMER register offset. If it's not zero, TIMER2 is using
irq. And it could be configured as clock event. Otherwise, TIMER1 is clock
event.
We must make sure that only one of all sp804 timers is using this property.

alias:
linux,clocksource = <&sp804-A>
linux,clockevent = <&sp804-A>

Although both of them points to timerA, only TIMER1 or TIMER2 of sp804
is using irq. So one is clock source, and the other is clock event.

alias:
linux,clocksource = <&sp804-A>
linux,clockevent = <&sp804-B>
The issue comes since system don't know whether TIMER1 or TIMER2 could
be configured as clock source.

We still need a new property to claim it. It seems that we can't drop
"arm,sp804-clocksource", although everybody don't like it.

What's your opinion?

>
> Where do you do this? In the Device Tree? No. In the kernel command
> line
Yes, command line could also be filled in DTS.

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 06/11] ARM: vexpress: use clocksource_of_init for sp804
  2013-03-13 15:59                 ` Haojian Zhuang
@ 2013-03-13 16:28                   ` Pawel Moll
  2013-03-13 16:32                   ` Rob Herring
  1 sibling, 0 replies; 44+ messages in thread
From: Pawel Moll @ 2013-03-13 16:28 UTC (permalink / raw)
  To: linux-arm-kernel

On Wed, 2013-03-13 at 15:59 +0000, Haojian Zhuang wrote:
> Maybe I didn't express my idea well. My point is that timer could be
> clock source
> /clock event. It could also just be a timer that user app or other device driver
> may want to use it directly. There're a lot of reason that user app or some
>  driver wants to use hardware timer. For example, the specific timer may
> keep running even system is in low power mode.

That's all fair enough. My point is in any case the *system* will take
care of setting this all up. Therefore it can manage the available
resources to avoid the conflict.

> Although there's so much hardware timers available, system must choose
> one for the usage of clock source / clock event / other hardware timer usage.

By all means. I'm just claiming that in normal situation it can choose
on its convenience. In other words - if there are no limitations in
hardware, it can pick any of them, being responsible for making the
right decision.

> >> >> Imagine that only TIMINT1 signal in sp804 is routed to interrupt controller.
> >> >> Could system still pick any one it wants?
> >> >
> >> Then we need another new property. I try to find using minim properties.
> >
> > No, we don't. See the discussion with Rob. He has an idea (using the
> > interrupt property only), I have another one (using already defined
> > interrupt-names property). I see you've just came with another one
> > (TIMINTC treated as TIMINT1), which is fine with me. Either way you've
> > got what you need to make the right decision.
> >
> After considered as second time, I think that we still need a property to meet
> alias usage. Excuse me expand it in this topic.
> 
> arm,sp804-has-irq = <offset>;
> The offset means TIMER register offset. If it's not zero, TIMER2 is using
> irq. And it could be configured as clock event. Otherwise, TIMER1 is clock
> event.
> We must make sure that only one of all sp804 timers is using this property.
> 
> alias:
> linux,clocksource = <&sp804-A>
> linux,clockevent = <&sp804-A>
> 
> Although both of them points to timerA, only TIMER1 or TIMER2 of sp804
> is using irq. So one is clock source, and the other is clock event.
> 
> alias:
> linux,clocksource = <&sp804-A>
> linux,clockevent = <&sp804-B>
> The issue comes since system don't know whether TIMER1 or TIMER2 could
> be configured as clock source.
> 
> We still need a new property to claim it. It seems that we can't drop
> "arm,sp804-clocksource", although everybody don't like it.
> 
> What's your opinion?

Let me repeat myself - I'm not saying that there must be no such thing
like the alias (or your property). I'm sure there will be a use case for
them.

What I am saying is that they should not be obligatory. Shortly speaking
- I don't want to have them in VE DTS files. For VE platform the driver
should pick one of the timers and use it as clocksource (I don't care
which one), another one as clockevent (again, it's up to you) and the
rest for whatever it wants. 

Could you please provide a solution for such a "generic" case, when
there are no aliases defined in the tree? I see no problem with checking
if the aliases exist and if they don't picking the first SP804 you can
get hold of. Just give me that and you won't hear me complaining
further :-)

> > Where do you do this? In the Device Tree? No. In the kernel command
> > line
> Yes, command line could also be filled in DTS.

Which is a very bad practice... There's a reason why "chosen" node is
named like this ;-)

Pawe?

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 06/11] ARM: vexpress: use clocksource_of_init for sp804
  2013-03-13 15:59                 ` Haojian Zhuang
  2013-03-13 16:28                   ` Pawel Moll
@ 2013-03-13 16:32                   ` Rob Herring
  2013-03-15 12:34                     ` Russell King - ARM Linux
  1 sibling, 1 reply; 44+ messages in thread
From: Rob Herring @ 2013-03-13 16:32 UTC (permalink / raw)
  To: linux-arm-kernel

On 03/13/2013 10:59 AM, Haojian Zhuang wrote:
> On 13 March 2013 23:19, Pawel Moll <pawel.moll@arm.com> wrote:
>> On Wed, 2013-03-13 at 15:01 +0000, Haojian Zhuang wrote:
>>> Yes, it's possible. Since only clocksource / clockevent is using SP804 timer
>>> on the VE platform. If user app or something else is using other SP804
>>> timer, it would be mess because of resource conflict.
>>
>> How would you expose this device to the app or something else? It's an
>> amba_bus device, so it must be bound with an amba_driver. Otherwise
>> you're abusing the device model and, well, you're on your own.
>>
>> The devices are managed by the system. The device tree is merely a
>> description of the available hardware.
>>
> Maybe I didn't express my idea well. My point is that timer could be
> clock source
> /clock event. It could also just be a timer that user app or other device driver
> may want to use it directly. There're a lot of reason that user app or some
>  driver wants to use hardware timer. For example, the specific timer may
> keep running even system is in low power mode.
> 
> Although there's so much hardware timers available, system must choose
> one for the usage of clock source / clock event / other hardware timer usage.
> 
>>>>> Imagine that only TIMINT1 signal in sp804 is routed to interrupt controller.
>>>>> Could system still pick any one it wants?
>>>>
>>> Then we need another new property. I try to find using minim properties.
>>
>> No, we don't. See the discussion with Rob. He has an idea (using the
>> interrupt property only), I have another one (using already defined
>> interrupt-names property). I see you've just came with another one
>> (TIMINTC treated as TIMINT1), which is fine with me. Either way you've
>> got what you need to make the right decision.
>>
> After considered as second time, I think that we still need a property to meet
> alias usage. Excuse me expand it in this topic.
> 
> arm,sp804-has-irq = <offset>;

Interrupt/timer number not offset please. The offset is implied by the
fact that the h/w is an sp804. The Integrator AP is not actually an
sp804, so it's init should be handled differently with a different
compatible property.

> The offset means TIMER register offset. If it's not zero, TIMER2 is using
> irq. And it could be configured as clock event. Otherwise, TIMER1 is clock
> event.
> We must make sure that only one of all sp804 timers is using this property.
> 
> alias:
> linux,clocksource = <&sp804-A>
> linux,clockevent = <&sp804-A>
> 
> Although both of them points to timerA, only TIMER1 or TIMER2 of sp804
> is using irq. So one is clock source, and the other is clock event.
> 
> alias:
> linux,clocksource = <&sp804-A>
> linux,clockevent = <&sp804-B>
> The issue comes since system don't know whether TIMER1 or TIMER2 could
> be configured as clock source.

If you have 2 sp804's, why do you care which one is used by the OS? If
they are identical, then it doesn't matter. If they are not, then
describe how they are not identical.

The realview and versatile boards currently do this, but there is no
good reason that I see and I intend to change this.

> We still need a new property to claim it. It seems that we can't drop
> "arm,sp804-clocksource", although everybody don't like it.
> 
> What's your opinion?

As previously stated, I don't think we need this or the alias based on
current in tree users.

There is an issue that you don't know about all available timers so you
can select the one with the minimum required features leaving others
with more features (i.e. an irq) free. If you need more control like
this then you can do custom setup before or instead of calling
clocksource_of_init. None of the current platforms have this issue nor
do they use sp804 for anything beyond clksrc and clkevt. I would not
expect lots of new users of sp804 as I expect most new platforms will
use architected timers. So let's not solve imaginary problems now.

Rob

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 03/11] clocksource: sp804: add device tree support
  2013-03-13 15:49                       ` Pawel Moll
@ 2013-03-13 16:35                         ` Arnd Bergmann
  2013-03-13 16:41                           ` Pawel Moll
  0 siblings, 1 reply; 44+ messages in thread
From: Arnd Bergmann @ 2013-03-13 16:35 UTC (permalink / raw)
  To: linux-arm-kernel

On Wednesday 13 March 2013, Pawel Moll wrote:
> Fine, so simply reverse the logic and drop the "arm,sp804-clock*"
> properties. Something like:
> 
> if (has_timint1) {
>         evtoffs = TIMER_1_BASE;
>         irq = irq_of_parse_and_map(np, 1);
>         srcoffs = TIMER_2_BASE;
> } else (has_timint2) {
>         evtoffs = TIMER_2_BASE;
>         irq = irq_of_parse_and_map(np, 2);
>         srcoffs = TIMER_1_BASE;
> } else {
>         can't be clockevent, sorry
> }
> 
> Hope it makes clear what I'd expect from the driver.

Makes sense. I guess you can actually derive "has_timint1"
from the presence of the irq and just try to parse it:

	irq = irq_of_parse_and_map(np, 0);
	if (irq) {
		evtoffs = TIMER_1_BASE;
		srcoffs = TIMER_2_BASE;
	} else {
		irq = irq_of_parse_and_map(np, 1);
		if (!irq)
			return -ENODEV;
		srcoffs = TIMER_1_BASE;
		evtoffs = TIMER_2_BASE;
	}


I wonder if we can ever get into the second case though: If the
first interrupt in not valid, can there be a second one in the
interrupts property? I don't know of a way to put an "invalid"
interrupt in there.

	Arnd

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 03/11] clocksource: sp804: add device tree support
  2013-03-13 16:35                         ` Arnd Bergmann
@ 2013-03-13 16:41                           ` Pawel Moll
  0 siblings, 0 replies; 44+ messages in thread
From: Pawel Moll @ 2013-03-13 16:41 UTC (permalink / raw)
  To: linux-arm-kernel

On Wed, 2013-03-13 at 16:35 +0000, Arnd Bergmann wrote:
> Makes sense. I guess you can actually derive "has_timint1"
> from the presence of the irq and just try to parse it:
> 
> 	irq = irq_of_parse_and_map(np, 0);
> 	if (irq) {
> 		evtoffs = TIMER_1_BASE;
> 		srcoffs = TIMER_2_BASE;
> 	} else {
> 		irq = irq_of_parse_and_map(np, 1);
> 		if (!irq)
> 			return -ENODEV;
> 		srcoffs = TIMER_1_BASE;
> 		evtoffs = TIMER_2_BASE;
> 	}
> 
> 
> I wonder if we can ever get into the second case though: If the
> first interrupt in not valid, can there be a second one in the
> interrupts property? I don't know of a way to put an "invalid"
> interrupt in there.

The discussion in the "[PATCH v3 03/11] clocksource: sp804: add device
tree support" thread resulted in some ideas how to describe such
situation. I suggested using interrupt-names property to explicitly
describe the numbers, Rob wanted to simply define one or two interrupts
and in the former case have a special property describing which one is
it. Either way you can get this information from the tree. The main
argument is about the clockevent/source aliases - whether they should be
obligatory, optional or banned.

Pawe?

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 03/11] clocksource: sp804: add device tree support
  2013-03-13 14:17     ` Rob Herring
  2013-03-13 14:42       ` Pawel Moll
@ 2013-03-15 12:20       ` Russell King - ARM Linux
  1 sibling, 0 replies; 44+ messages in thread
From: Russell King - ARM Linux @ 2013-03-15 12:20 UTC (permalink / raw)
  To: linux-arm-kernel

On Wed, Mar 13, 2013 at 09:17:21AM -0500, Rob Herring wrote:
> How about:
> 
> 1 irq - TIMINT1
> 2 irqs w/ same source # - TIMINTC
> 2 irqs w/ different source # - TIMINT1 and TIMINT2
> 
> I'm not completely sure if Linux and the irq domain code handles the
> same interrupt source repeated. It should because that is basically a
> shared irq line.

I think you're missing something here.  Any particular platform will
generally only wire either the common interrupt, or the individual
interrupts.  Very few, if any, will wire both.

It's just like stuff such as MMCI and the UARTs.  They have a combined
interrupt out, and individual interrupt outs.  However, they're all
written for the combined interrupt only, because practically no one
uses the individal interrupts.

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 06/11] ARM: vexpress: use clocksource_of_init for sp804
  2013-03-13 16:32                   ` Rob Herring
@ 2013-03-15 12:34                     ` Russell King - ARM Linux
  2013-03-15 12:58                       ` Pawel Moll
  0 siblings, 1 reply; 44+ messages in thread
From: Russell King - ARM Linux @ 2013-03-15 12:34 UTC (permalink / raw)
  To: linux-arm-kernel

On Wed, Mar 13, 2013 at 11:32:01AM -0500, Rob Herring wrote:
> If you have 2 sp804's, why do you care which one is used by the OS? If
> they are identical, then it doesn't matter. If they are not, then
> describe how they are not identical.
> 
> The realview and versatile boards currently do this, but there is no
> good reason that I see and I intend to change this.

It is highly likely that the timer choice on these boards was made by
independent people, who came up with different random choices.  Nothing
more than that - I believe it to be entirely arbitary.  I do think
discussion is getting too bogged down on this point.

So, we could make the decision about which timer to use for the clock
event based on whether an interrupt is specified, the known clock rate
and size of the timer register.

Same can be done for the clock source, but preferring a timer without
an interrupt in preference to one with an interrupt.

We do have this nice rating system for clocksources and clockevents -
and it could be more flexible if it didn't separate clocksources from
clockevents - allowing just a single "timer" and marking it as being
suitable as a clocksource or a clockevent, or indeed both.

However, for SP804 selection, there are cases where it matters, such as
on Versatile Express where you have to select the right set of SP804 to
have a working system (because ARM didn't fully document the SP804 setup
there) and we have no way to switch some of those timers from their
32kHz clock source.  But then we could just omit the clock source for
the "bad" SP804s which would prevent them being used.

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 06/11] ARM: vexpress: use clocksource_of_init for sp804
  2013-03-15 12:34                     ` Russell King - ARM Linux
@ 2013-03-15 12:58                       ` Pawel Moll
  2013-03-15 18:10                         ` Russell King - ARM Linux
  0 siblings, 1 reply; 44+ messages in thread
From: Pawel Moll @ 2013-03-15 12:58 UTC (permalink / raw)
  To: linux-arm-kernel

On Fri, 2013-03-15 at 12:34 +0000, Russell King - ARM Linux wrote:
> However, for SP804 selection, there are cases where it matters, such as
> on Versatile Express where you have to select the right set of SP804 to
> have a working system (because ARM didn't fully document the SP804 setup
> there) and we have no way to switch some of those timers from their
> 32kHz clock source.  But then we could just omit the clock source for
> the "bad" SP804s which would prevent them being used.

Both VE motherboard's SP804s TIMCLKENx inputs are fed by the SP810's
outputs:

v2m_timer01: timer at 11000 {
	compatible = "arm,sp804", "arm,primecell";
	reg = <0x11000 0x1000>;
	interrupts = <2>;
	clocks = <&v2m_sysctl 0>, <&v2m_sysctl 1>, <&smbclk>;
	clock-names = "timclken1", "timclken2", "apb_pclk";
};      

v2m_timer23: timer at 12000 {
	compatible = "arm,sp804", "arm,primecell";
	reg = <0x12000 0x1000>;
	interrupts = <3>;
	clocks = <&v2m_sysctl 2>, <&v2m_sysctl 3>, <&smbclk>;
	clock-names = "timclken1", "timclken2", "apb_pclk";
};

TIMCLKs are wired to the SMB_CLK, so the effective rate depends on the
TIMCLKENx only.

The SP810 takes the 32kHz and 1MHz reference clocks:

v2m_sysctl: sysctl at 01000 {
	compatible = "arm,sp810", "arm,primecell";
	reg = <0x01000 0x1000>;
	clocks = <&v2m_refclk32khz>, <&v2m_refclk1mhz>, <&smbclk>;
	clock-names = "refclk", "timclk", "apb_pclk";
	#clock-cells = <1>;
	clock-output-names = "timerclken0", "timerclken1", "timerclken2", "timerclken3";
};

and the code in drivers/clk/versatile/clk-vexpress.c picks up the faster
one as the parent.

The V2P-CA9 SP804's TIMCLK is wired to one of the main clock generators:

timer at 100e4000 {
	compatible = "arm,sp804", "arm,primecell";
	reg = <0x100e4000 0x1000>;
	interrupts = <0 48 4>,
	             <0 49 4>;
	clocks = <&oscclk2>, <&oscclk2>;
	clock-names = "timclk", "apb_pclk";
};

Both TIMCLKEN0 & 1 are pulled up to 1 so they have no effect on the
timer rates.

Overall, the description of the VE clocking in the Device Tree is rather
complete.

Pawe?

^ permalink raw reply	[flat|nested] 44+ messages in thread

* [PATCH v3 06/11] ARM: vexpress: use clocksource_of_init for sp804
  2013-03-15 12:58                       ` Pawel Moll
@ 2013-03-15 18:10                         ` Russell King - ARM Linux
  0 siblings, 0 replies; 44+ messages in thread
From: Russell King - ARM Linux @ 2013-03-15 18:10 UTC (permalink / raw)
  To: linux-arm-kernel

On Fri, Mar 15, 2013 at 12:58:32PM +0000, Pawel Moll wrote:
> On Fri, 2013-03-15 at 12:34 +0000, Russell King - ARM Linux wrote:
> > However, for SP804 selection, there are cases where it matters, such as
> > on Versatile Express where you have to select the right set of SP804 to
> > have a working system (because ARM didn't fully document the SP804 setup
> > there) and we have no way to switch some of those timers from their
> > 32kHz clock source.  But then we could just omit the clock source for
> > the "bad" SP804s which would prevent them being used.
> 
> Both VE motherboard's SP804s TIMCLKENx inputs are fed by the SP810's
> outputs:

Sigh.

You do remember who (re)wrote the Versatile Express support that's in
mainline... I know that the motherboard SP804s are clocked from the
SP810 (which has no published documentation) and these are selectable
between 1MHz and 32kHz.

What I was referring to is the SP804s on the CT9x4 tile, which seem
to be clocked at 32kHz with no way to change them, and it's that which
has been totally and utterly undocumented (believe me, when I did that
work above, I searched the available documentation many times.)

It may be that as a result of my complaints to ARM about that, the
documentation has since been fixed.  Whether it makes sense to use
the CT9x4 SP804s over the motherboards, I've no idea because I've been
forced out of the loop on Versatile Express.

^ permalink raw reply	[flat|nested] 44+ messages in thread

end of thread, other threads:[~2013-03-15 18:10 UTC | newest]

Thread overview: 44+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2013-03-13  5:05 [PATCH v3 00/11] add hisilicon SoC support Haojian Zhuang
2013-03-13  5:05 ` [PATCH v3 01/11] clocksource: move sp timer driver Haojian Zhuang
2013-03-13  5:05 ` [PATCH v3 02/11] clocksource: select USE_OF by default Haojian Zhuang
2013-03-13  5:05 ` [PATCH v3 03/11] clocksource: sp804: add device tree support Haojian Zhuang
2013-03-13 11:05   ` Pawel Moll
2013-03-13 11:37     ` Haojian Zhuang
2013-03-13 11:41       ` Pawel Moll
2013-03-13 14:17     ` Rob Herring
2013-03-13 14:42       ` Pawel Moll
2013-03-13 14:51         ` Rob Herring
2013-03-13 14:55           ` Pawel Moll
2013-03-13 15:11             ` Haojian Zhuang
2013-03-13 15:23               ` Pawel Moll
2013-03-13 15:25                 ` Haojian Zhuang
2013-03-13 15:29                   ` Pawel Moll
2013-03-13 15:39                     ` Rob Herring
2013-03-13 15:41                       ` Pawel Moll
2013-03-13 15:44                         ` Haojian Zhuang
2013-03-13 15:42                     ` Haojian Zhuang
2013-03-13 15:49                       ` Pawel Moll
2013-03-13 16:35                         ` Arnd Bergmann
2013-03-13 16:41                           ` Pawel Moll
2013-03-15 12:20       ` Russell King - ARM Linux
2013-03-13  5:05 ` [PATCH v3 04/11] ARM: integrator: use clocksource_of_init for sp804 Haojian Zhuang
2013-03-13  5:05 ` [PATCH v3 05/11] ARM: highbank: " Haojian Zhuang
2013-03-13  5:05 ` [PATCH v3 06/11] ARM: vexpress: " Haojian Zhuang
2013-03-13 11:10   ` Pawel Moll
2013-03-13 11:42     ` Haojian Zhuang
2013-03-13 11:46       ` Pawel Moll
2013-03-13 12:21         ` Haojian Zhuang
2013-03-13 14:48           ` Pawel Moll
2013-03-13 15:01             ` Haojian Zhuang
2013-03-13 15:19               ` Pawel Moll
2013-03-13 15:59                 ` Haojian Zhuang
2013-03-13 16:28                   ` Pawel Moll
2013-03-13 16:32                   ` Rob Herring
2013-03-15 12:34                     ` Russell King - ARM Linux
2013-03-15 12:58                       ` Pawel Moll
2013-03-15 18:10                         ` Russell King - ARM Linux
2013-03-13  5:05 ` [PATCH v3 07/11] ARM: debug: support debug ll on hisilicon soc Haojian Zhuang
2013-03-13  5:05 ` [PATCH v3 08/11] clk: hi3xxx: add clock support Haojian Zhuang
2013-03-13  5:05 ` [PATCH v3 09/11] ARM: hi3xxx: add board support with device tree Haojian Zhuang
2013-03-13  5:05 ` [PATCH v3 10/11] ARM: hi3xxx: enable hi4511 " Haojian Zhuang
2013-03-13  5:05 ` [PATCH v3 11/11] ARM: config: append arch hi3xxx into multi defconfig Haojian Zhuang

This is a public inbox, see mirroring instructions
on how to clone and mirror all data and code used for this inbox