Re: [PATCH v2 0/3] ARM: sun8i: a83t: Support Camera Sensor Interface controller

[Chen-Yu Tsai <wens@kernel.org>]

On Mon, May 20, 2019 at 11:10 PM Ondřej Jirman <megous@megous.com> wrote:
>
> On Mon, May 20, 2019 at 05:06:34PM +0200, verejna wrote:
> > From: Ondrej Jirman <megous@megous.com>
> >
> > This is a re-send of Chen-Yu's A83T CSI patch series with review tags
> > applied and removed address/size cells from csi_in port. Already applied
> > patches from v1  were dropped.
> >
> > The series is ready to be merged:
> >
> >   Patch 1 and 2 via sunxi tree
> >   Patch 3 via media tree
>
> Sorry, wrong numbers. 2 is for media tree, 3 is for sunxi, 1 is a dt-bindings
> patch, where I'm not sure.

Bindings typically go with the driver.

Sakari, this series is and has been ready for some time since before the merge
window. Could you please merge patches 1 and 2.


Thanks
ChenYu


>
> thanks,
>         Ondrej
>
> > v2:
> > - dropped address/size cells from csi_in port
> > - added review tags
> >
> > Please take a look and merge.
> >
> > Thank you,
> >       Ondrej
> >
> > --------------------------
> > Original description:
> >
> > Hi everyone,
> >
> > This series adds support for the camera sensor interface controller
> > found on the Allwinner A83T SoC. The controller is similar to the one
> > found on  the H3, with the addition of a MIPI CSI-2 interface. However,
> > this series only supports parallel and BT.656 interfaces, based on the
> > existing driver.
> >
> > Patch 1 adds an undocumented clock parent of the CSI MCLK. This was
> > found after finding the default value to sometimes work and sometimes
> > not, and then comparing against BSP code.
> >
> > Patch 2 adds a compatible string for the A83T variant.
> >
> > Patch 3 adds support for the A83T variant to the existing sun6i-csi
> > driver.
> >
> > Patch 4 adds a device node for the controller, as well as commonly
> > used pin muxing options.
> >
> > Patch 5 adds a pin muxing option for I2C1 on the PE pins, used in
> > conjunction with the CSI pins.
> >
> > Patch 6 provides an example usage of the CSI controller: the Bananapi M3
> > with its camera module attached.
> >
> > Please have a look.
> >
> > Regards
> > ChenYu
> >
> > Chen-Yu Tsai (3):
> >   dt-bindings: media: sun6i-csi: Add compatible string for A83T variant
> >   media: sun6i: Support A83T variant
> >   ARM: dts: sun8i: a83t: Add device node for CSI (Camera Sensor
> >     Interface)
> >
> >  .../devicetree/bindings/media/sun6i-csi.txt   |  1 +
> >  arch/arm/boot/dts/sun8i-a83t.dtsi             | 29 +++++++++++++++++++
> >  .../platform/sunxi/sun6i-csi/sun6i_csi.c      |  1 +
> >  3 files changed, 31 insertions(+)
> >
> > --
> > 2.21.0
> >
> >
> > _______________________________________________
> > linux-arm-kernel mailing list
> > linux-arm-kernel@lists.infradead.org
> > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel