Re: [PATCH 0/4] Fix the i2c/clk bug of stm32 mcu platform

[Dillon Min <dillon.minfei@gmail.com>]

Hi Patrice

Thanks for your time to test my patch.

On Mon, May 31, 2021 at 9:20 PM Patrice CHOTARD
<patrice.chotard@foss.st.com> wrote:
>
> Hi Dillon
>
>
>
> On 5/14/21 1:02 PM, dillon.minfei@gmail.com wrote:
> > From: Dillon Min <dillon.minfei@gmail.com>
> >
> > This seriese fix three i2c/clk bug for stm32 f4/f7
> > - kernel runing in sdram, i2c driver get data timeout
> > - ltdc clk turn off after kernel console active
> > - kernel hang in set ltdc clock rate
> >
> > clk bug found on stm32f429/f469-disco board
> >
> > Hi Patrice:
> > below is the guide to verify the patch:
> >
> > setup test env with following files(link at below 'files link'):
> > [1] u-boot-dtb.bin
> > [2] rootfs zip file (used in kernel initramfs)
> > [3] u-boot's mkimage to create itb file
> > [4] kernel config file
> > [5] my itb with-or-without i2c patch
> >
> > This patch based on kernel commit:
> > 88b06399c9c766c283e070b022b5ceafa4f63f19
> >
> > Note:
> > panel-ilitek-ili9341.c is the driver which was submitted last year, but not
> > get accepted. it's used to setup touch screen calibration, then test i2c.
> >
> > create itb file(please correct path of 'data'):
> > ./mkimage -f stm32.its stm32.itb
> >
> > HW setup:
> > console:
> >        PA9, PA10
> >        usart0
> >        serial@40011000
> >        115200 8n1
> >
> > -- flash u-boot.bin to stm32f429-disco on PC
> > $ sudo openocd -f board/stm32f429discovery.cfg -c \
> >   '{PATH-TO-YOUR-UBOOT}/u-boot-dtb.bin 0x08000000 exit reset'
> >
> > -- setup kernel load bootargs at u-boot
> > U-Boot > setenv bootargs 'console=tty0 console=ttySTM0,115200
> >                     root=/dev/ram rdinit=/linuxrc loglevel=8 fbcon=rotate:2'
> > U-Boot > loady;bootm
> > (download stm32.dtb or your kernel with itb format, or download zImage, dtb)
> >
>
>
> Thanks for these informations
> I was able to load and boot DTB and uImage directly in SDRAM as you suggested,
> i saw Linux logo and kernel log on the STM32F429-disco display,
> but i can't reach the login.
>
> The last kernel log i got is :
>
> Starting kernel ...
>
> [    0.000000] Booting Linux on physical CPU 0x0
> [    0.000000] Linux version 5.13.0-rc1-00082-g9dbbd5cb6240-dirty (nxp11987@lmecxl0573.lme1
> [    0.000000] CPU: ARMv7-M [410fc241] revision 1 (ARMv7M), cr=00000000
> [    0.000000] CPU: unknown data cache, unknown instruction cache
> [    0.000000] OF: fdt: Machine model: STMicroelectronics STM32F429i-DISCO board
> [    0.000000] Zone ranges:
> [    0.000000]   Normal   [mem 0x0000000090000000-0x00000000907fffff]
> [    0.000000] Movable zone start for each node
> [    0.000000] Early memory node ranges
>
> [...]
>
> [    2.637564] printk: console [ttySTM0] enabled
> [    2.747984] panel-ilitek-ili9341 spi0.1: get optional vcc failed
> [    2.758986] spi_stm32 40015000.spi: driver initialized
> [    2.795733] i2c /dev entries driver
> [    2.849955] stmpe-i2c 0-0041: stmpe811 detected, chip id: 0x811
> [    2.922030] stmpe-ts stmpe-ts: DMA mask not set
> [    2.965729] input: stmpe-ts as /devices/platform/soc/40005c00.i2c/i2c-0/0-0041/stmpe-ts0
> [    2.991570] stm32f4-i2c 40005c00.i2c: STM32F4 I2C driver registered
> [    3.058262] [drm] Initialized stm 1.0.0 20170330 for 40016800.display-controller on min0
> [    3.665951] panel-ilitek-ili9341 spi0.1: initialized display rgb interface
> [    3.765208] Console: switching to colour frame buffer device 30x40
> [    4.014269] stm32-display 40016800.display-controller: [drm] fb0: stmdrmfb frame buffere
> [    4.212737] Freeing unused kernel memory: 324K
> [    4.287300] This architecture does not have kernel memory protection.
> [    4.401202] Run /linuxrc as init process
> [    4.478622]   with arguments:
> [    4.555069]     /linuxrc
> [    4.595406]   with environment:
> [    4.672213]     HOME=/
> [    4.712511]     TERM=linux
> [  206.785289] random: crng init done

I guess you didn't add the rootfs to uImage I sent you.
Could you post all the logs from u-boot startup to kernel log end.

If possible, you can try my suggestion.
- tar -jxf stm32_rootfs.tar.bz2
- add stm32_rootfs to your kernel config( enable initramfs)
- make O=YOUR_KERNEL_OUT zImage dtbs LOADADDR=0x90008000
- create itb file (combine dtb and kernel, initramfs) by mkimage
  ./mkimage -f stm32.its stm32.itb
  (before above command, make sure you correct stm32.its adapt to your env)

This process will make u-boot to load the kernel more simple.

Thanks.

Best Regards.
Dillon


>
>
> I can't test your I2C patch.
>
> Patrice
>
>
> > -- setup ts_calibrate running env on stm32f429-disco
> > / # export TSLIB_CONFFILE=/etc/ts.conf
> > / # export TSLIB_TSDEVICE=/dev/input/event0
> > / # export TSLIB_CONSOLEDEVICE=none
> > / # export TSLIB_FBDEVICE=/dev/fb0
> >
> > -- clear screen
> > / # ./fb
> >
> > -- run ts_calibrate
> > / # ts_calibrate
> > (you can calibrate touchscreen now, and get below errors)
> >
> > [  113.942087] stmpe-i2c0-0041: failed to read regs 0x52: -110
> > [  114.063598] stmpe-i2c 0-0041: failed to read reg 0x4b: -16
> > [  114.185629] stmpe-i2c 0-0041: failed to read reg 0x40: -16
> > [  114.307257] stmpe-i2c 0-0041: failed to write reg 0xb: -16
> >
> > ...
> > with i2c patch applied, you will find below logs:
> >
> > RAW---------------------> 3164 908 183 118.110884
> > TS_READ_RAW----> x = 3164, y =908, pressure = 183
> > RAW---------------------> 3166 922 126 118.138946
> > TS_READ_RAW----> x = 3166, y = 922, pressure = 126
> > ....
> >
> > files link:
> > https://drive.google.com/drive/folders/1qNbjChcB6UGtKzne2F5x9_WG_sZFyo3o?usp=sharing
> >
> >
> >
> >
> > Dillon Min (4):
> >   drm/panel: Add ilitek ili9341 panel driver
> >   i2c: stm32f4: Fix stmpe811 get xyz data timeout issue
> >   clk: stm32: Fix stm32f429's ltdc driver hang in set clock rate
> >   clk: stm32: Fix ltdc's clock turn off by clk_disable_unused() after
> >     kernel startup
> >
> >  drivers/clk/clk-stm32f4.c                    |   10 +-
> >  drivers/gpu/drm/panel/Kconfig                |   12 +
> >  drivers/gpu/drm/panel/Makefile               |    1 +
> >  drivers/gpu/drm/panel/panel-ilitek-ili9341.c | 1285 ++++++++++++++++++++++++++
> >  drivers/i2c/busses/i2c-stm32f4.c             |   12 +-
> >  5 files changed, 1310 insertions(+), 10 deletions(-)
> >  create mode 100755 drivers/gpu/drm/panel/panel-ilitek-ili9341.c
> >

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel