Re: [PATCH v3 07/13] phy: usb: Add support for new Synopsis USB controller on the 7216

[Alan Cooper <alcooperx@gmail.com>]

On Fri, Jan 3, 2020 at 4:31 AM Kishon Vijay Abraham I <kishon@ti.com> wrote:
>
> Hi,
>
> On 10/12/19 6:51 PM, Al Cooper wrote:
> > The 7216 has the new USB XHCI controller from Synopsis. While
> > this new controller and the PHY are similar to the STB versions,
> > the major differences are:
> >
> > - Many of the registers and fields in the CTRL block have been
> >   removed or changed.
> > - A new set of Synopsis control registers, BCHP_USB_XHCI_GBL, were
> >   added.
>
> Is it not Synopsys?

Yes, I'll send a v4 of patches 7 and 8


On Fri, Jan 3, 2020 at 4:31 AM Kishon Vijay Abraham I <kishon@ti.com> wrote:
>
> Hi,
>
> On 10/12/19 6:51 PM, Al Cooper wrote:
> > The 7216 has the new USB XHCI controller from Synopsis. While
> > this new controller and the PHY are similar to the STB versions,
> > the major differences are:
> >
> > - Many of the registers and fields in the CTRL block have been
> >   removed or changed.
> > - A new set of Synopsis control registers, BCHP_USB_XHCI_GBL, were
> >   added.
>
> Is it not Synopsys?
>
> Thanks
> Kishon
>
> > - MDIO functionality has been replaced with direct access registers
> >   in the BCHP_USB_XHCI_GBL block.
> > - Power up PHY defaults that had to be changed by MDIO in previous
> >   chips will now power up with the correct defaults.
> >
> > A new init module was created for this new Synopsis USB controller.
> > A new compatible string was added and the driver will dispatch
> > into one of two init modules based on it. A "reg-names" field was
> > added so the driver can more easily get optional registers.
> > A DT bindings document was also added for this driver.
> >
> > Signed-off-by: Al Cooper <alcooperx@gmail.com>
> > ---
> >  drivers/phy/broadcom/Makefile                 |   2 +-
> >  .../phy/broadcom/phy-brcm-usb-init-synopsis.c | 171 ++++++++++++++++++
> >  drivers/phy/broadcom/phy-brcm-usb-init.h      |   2 +
> >  drivers/phy/broadcom/phy-brcm-usb.c           |  70 +++++--
> >  4 files changed, 227 insertions(+), 18 deletions(-)
> >  create mode 100644 drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
> >
> > diff --git a/drivers/phy/broadcom/Makefile b/drivers/phy/broadcom/Makefile
> > index f453c7d3ffff..88523e2be861 100644
> > --- a/drivers/phy/broadcom/Makefile
> > +++ b/drivers/phy/broadcom/Makefile
> > @@ -8,7 +8,7 @@ obj-$(CONFIG_PHY_NS2_USB_DRD)         += phy-bcm-ns2-usbdrd.o
> >  obj-$(CONFIG_PHY_BRCM_SATA)          += phy-brcm-sata.o
> >  obj-$(CONFIG_PHY_BRCM_USB)           += phy-brcm-usb-dvr.o
> >
> > -phy-brcm-usb-dvr-objs := phy-brcm-usb.o phy-brcm-usb-init.o
> > +phy-brcm-usb-dvr-objs := phy-brcm-usb.o phy-brcm-usb-init.o phy-brcm-usb-init-synopsis.o
> >
> >  obj-$(CONFIG_PHY_BCM_SR_PCIE)                += phy-bcm-sr-pcie.o
> >  obj-$(CONFIG_PHY_BCM_SR_USB)         += phy-bcm-sr-usb.o
> > diff --git a/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c b/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
> > new file mode 100644
> > index 000000000000..57663492b228
> > --- /dev/null
> > +++ b/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
> > @@ -0,0 +1,171 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/* Copyright (c) 2018, Broadcom */
> > +
> > +/*
> > + * This module contains USB PHY initialization for power up and S3 resume
> > + * for newer Synopsis based USB hardware first used on the bcm7216.
> > + */
> > +
> > +#include <linux/delay.h>
> > +#include <linux/io.h>
> > +
> > +#include <linux/soc/brcmstb/brcmstb.h>
> > +#include "phy-brcm-usb-init.h"
> > +
> > +/* Register definitions for the USB CTRL block */
> > +#define USB_CTRL_SETUP                       0x00
> > +#define   USB_CTRL_SETUP_STRAP_IPP_SEL_MASK          0x02000000
> > +#define   USB_CTRL_SETUP_SCB2_EN_MASK                        0x00008000
> > +#define   USB_CTRL_SETUP_SCB1_EN_MASK                        0x00004000
> > +#define   USB_CTRL_SETUP_SOFT_SHUTDOWN_MASK          0x00000200
> > +#define   USB_CTRL_SETUP_IPP_MASK                    0x00000020
> > +#define   USB_CTRL_SETUP_IOC_MASK                    0x00000010
> > +#define USB_CTRL_USB_PM                      0x04
> > +#define   USB_CTRL_USB_PM_USB_PWRDN_MASK             0x80000000
> > +#define   USB_CTRL_USB_PM_SOFT_RESET_MASK            0x40000000
> > +#define   USB_CTRL_USB_PM_BDC_SOFT_RESETB_MASK               0x00800000
> > +#define   USB_CTRL_USB_PM_XHC_SOFT_RESETB_MASK               0x00400000
> > +#define USB_CTRL_USB_PM_STATUS               0x08
> > +#define USB_CTRL_USB_DEVICE_CTL1     0x10
> > +#define   USB_CTRL_USB_DEVICE_CTL1_PORT_MODE_MASK    0x00000003
> > +
> > +
> > +static void xhci_soft_reset(struct brcm_usb_init_params *params,
> > +                     int on_off)
> > +{
> > +     void __iomem *ctrl = params->ctrl_regs;
> > +
> > +     /* Assert reset */
> > +     if (on_off)
> > +             USB_CTRL_UNSET(ctrl, USB_PM, XHC_SOFT_RESETB);
> > +     /* De-assert reset */
> > +     else
> > +             USB_CTRL_SET(ctrl, USB_PM, XHC_SOFT_RESETB);
> > +}
> > +
> > +static void usb_init_ipp(struct brcm_usb_init_params *params)
> > +{
> > +     void __iomem *ctrl = params->ctrl_regs;
> > +     u32 reg;
> > +     u32 orig_reg;
> > +
> > +     pr_debug("%s\n", __func__);
> > +
> > +     orig_reg = reg = brcm_usb_readl(USB_CTRL_REG(ctrl, SETUP));
> > +     if (params->ipp != 2)
> > +             /* override ipp strap pin (if it exits) */
> > +             reg &= ~(USB_CTRL_MASK(SETUP, STRAP_IPP_SEL));
> > +
> > +     /* Override the default OC and PP polarity */
> > +     reg &= ~(USB_CTRL_MASK(SETUP, IPP) | USB_CTRL_MASK(SETUP, IOC));
> > +     if (params->ioc)
> > +             reg |= USB_CTRL_MASK(SETUP, IOC);
> > +     if (params->ipp == 1)
> > +             reg |= USB_CTRL_MASK(SETUP, IPP);
> > +     brcm_usb_writel(reg, USB_CTRL_REG(ctrl, SETUP));
> > +
> > +     /*
> > +      * If we're changing IPP, make sure power is off long enough
> > +      * to turn off any connected devices.
> > +      */
> > +     if ((reg ^ orig_reg) & USB_CTRL_MASK(SETUP, IPP))
> > +             msleep(50);
> > +}
> > +
> > +static void usb_init_common(struct brcm_usb_init_params *params)
> > +{
> > +     u32 reg;
> > +     void __iomem *ctrl = params->ctrl_regs;
> > +
> > +     pr_debug("%s\n", __func__);
> > +
> > +     USB_CTRL_UNSET(ctrl, USB_PM, USB_PWRDN);
> > +     /* 1 millisecond - for USB clocks to settle down */
> > +     usleep_range(1000, 2000);
> > +
> > +     if (USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE)) {
> > +             reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
> > +             reg &= ~USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE);
> > +             reg |= params->mode;
> > +             brcm_usb_writel(reg, USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
> > +     }
> > +     switch (params->mode) {
> > +     case USB_CTLR_MODE_HOST:
> > +             USB_CTRL_UNSET(ctrl, USB_PM, BDC_SOFT_RESETB);
> > +             break;
> > +     default:
> > +             USB_CTRL_UNSET(ctrl, USB_PM, BDC_SOFT_RESETB);
> > +             USB_CTRL_SET(ctrl, USB_PM, BDC_SOFT_RESETB);
> > +             break;
> > +     }
> > +}
> > +
> > +static void usb_init_xhci(struct brcm_usb_init_params *params)
> > +{
> > +     pr_debug("%s\n", __func__);
> > +
> > +     xhci_soft_reset(params, 0);
> > +}
> > +
> > +static void usb_uninit_common(struct brcm_usb_init_params *params)
> > +{
> > +     void __iomem *ctrl = params->ctrl_regs;
> > +
> > +     pr_debug("%s\n", __func__);
> > +
> > +     USB_CTRL_SET(ctrl, USB_PM, USB_PWRDN);
> > +
> > +}
> > +
> > +static void usb_uninit_xhci(struct brcm_usb_init_params *params)
> > +{
> > +
> > +     pr_debug("%s\n", __func__);
> > +
> > +     xhci_soft_reset(params, 1);
> > +}
> > +
> > +static int usb_get_dual_select(struct brcm_usb_init_params *params)
> > +{
> > +     void __iomem *ctrl = params->ctrl_regs;
> > +     u32 reg = 0;
> > +
> > +     pr_debug("%s\n", __func__);
> > +
> > +     reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
> > +     reg &= USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE);
> > +     return reg;
> > +}
> > +
> > +static void usb_set_dual_select(struct brcm_usb_init_params *params, int mode)
> > +{
> > +     void __iomem *ctrl = params->ctrl_regs;
> > +     u32 reg;
> > +
> > +     pr_debug("%s\n", __func__);
> > +
> > +     reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
> > +     reg &= ~USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE);
> > +     reg |= mode;
> > +     brcm_usb_writel(reg, USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
> > +}
> > +
> > +
> > +static const struct brcm_usb_init_ops bcm7216_ops = {
> > +     .init_ipp = usb_init_ipp,
> > +     .init_common = usb_init_common,
> > +     .init_xhci = usb_init_xhci,
> > +     .uninit_common = usb_uninit_common,
> > +     .uninit_xhci = usb_uninit_xhci,
> > +     .get_dual_select = usb_get_dual_select,
> > +     .set_dual_select = usb_set_dual_select,
> > +};
> > +
> > +void brcm_usb_dvr_init_7216(struct brcm_usb_init_params *params)
> > +{
> > +
> > +     pr_debug("%s\n", __func__);
> > +
> > +     params->family_name = "7216";
> > +     params->ops = &bcm7216_ops;
> > +}
> > diff --git a/drivers/phy/broadcom/phy-brcm-usb-init.h b/drivers/phy/broadcom/phy-brcm-usb-init.h
> > index 7701872d1136..db6851c55335 100644
> > --- a/drivers/phy/broadcom/phy-brcm-usb-init.h
> > +++ b/drivers/phy/broadcom/phy-brcm-usb-init.h
> > @@ -43,6 +43,7 @@ struct brcm_usb_init_ops {
> >  struct  brcm_usb_init_params {
> >       void __iomem *ctrl_regs;
> >       void __iomem *xhci_ec_regs;
> > +     void __iomem *xhci_gbl_regs;
> >       int ioc;
> >       int ipp;
> >       int mode;
> > @@ -55,6 +56,7 @@ struct  brcm_usb_init_params {
> >  };
> >
> >  void brcm_usb_dvr_init_7445(struct brcm_usb_init_params *params);
> > +void brcm_usb_dvr_init_7216(struct brcm_usb_init_params *params);
> >
> >  static inline u32 brcm_usb_readl(void __iomem *addr)
> >  {
> > diff --git a/drivers/phy/broadcom/phy-brcm-usb.c b/drivers/phy/broadcom/phy-brcm-usb.c
> > index 9d93c5599511..64379ede480e 100644
> > --- a/drivers/phy/broadcom/phy-brcm-usb.c
> > +++ b/drivers/phy/broadcom/phy-brcm-usb.c
> > @@ -241,6 +241,15 @@ static const struct attribute_group brcm_usb_phy_group = {
> >       .attrs = brcm_usb_phy_attrs,
> >  };
> >
> > +static const struct of_device_id brcm_usb_dt_ids[] = {
> > +     {
> > +             .compatible = "brcm,bcm7216-usb-phy",
> > +             .data = &brcm_usb_dvr_init_7216,
> > +     },
> > +     { .compatible = "brcm,brcmstb-usb-phy" },
> > +     { /* sentinel */ }
> > +};
> > +
> >  static int brcm_usb_phy_dvr_init(struct platform_device *pdev,
> >                                struct brcm_usb_phy_data *priv,
> >                                struct device_node *dn)
> > @@ -316,13 +325,16 @@ static int brcm_usb_phy_dvr_init(struct platform_device *pdev,
> >
> >  static int brcm_usb_phy_probe(struct platform_device *pdev)
> >  {
> > -     struct resource *res;
> > +     struct resource *res_ctrl;
> > +     struct resource *res_xhciec = NULL;
> > +     struct resource *res_xhcigbl = NULL;
> >       struct device *dev = &pdev->dev;
> >       struct brcm_usb_phy_data *priv;
> >       struct phy_provider *phy_provider;
> >       struct device_node *dn = pdev->dev.of_node;
> >       int err;
> >       const char *mode;
> > +     const struct of_device_id *match;
> >
> >       priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> >       if (!priv)
> > @@ -331,30 +343,59 @@ static int brcm_usb_phy_probe(struct platform_device *pdev)
> >
> >       priv->ini.family_id = brcmstb_get_family_id();
> >       priv->ini.product_id = brcmstb_get_product_id();
> > -     brcm_usb_dvr_init_7445(&priv->ini);
> > +
> > +     match = of_match_node(brcm_usb_dt_ids, dev->of_node);
> > +     if (match && match->data) {
> > +             void (*dvr_init)(struct brcm_usb_init_params *params);
> > +
> > +             dvr_init = match->data;
> > +             (*dvr_init)(&priv->ini);
> > +     } else {
> > +             brcm_usb_dvr_init_7445(&priv->ini);
> > +     }
> > +
> >       dev_dbg(dev, "Best mapping table is for %s\n",
> >               priv->ini.family_name);
> > -     res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > -     if (!res) {
> > -             dev_err(dev, "can't get USB_CTRL base address\n");
> > -             return -EINVAL;
> > +
> > +     /* Newer DT node has reg-names. xhci_ec and xhci_gbl are optional. */
> > +     res_ctrl = platform_get_resource_byname(pdev, IORESOURCE_MEM, "ctrl");
> > +     if (res_ctrl != NULL) {
> > +             res_xhciec = platform_get_resource_byname(pdev,
> > +                                                       IORESOURCE_MEM,
> > +                                                       "xhci_ec");
> > +             res_xhcigbl = platform_get_resource_byname(pdev,
> > +                                                        IORESOURCE_MEM,
> > +                                                        "xhci_gbl");
> > +     } else {
> > +             /* Older DT node without reg-names, use index */
> > +             res_ctrl = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > +             if (res_ctrl == NULL) {
> > +                     dev_err(dev, "can't get CTRL base address\n");
> > +                     return -EINVAL;
> > +             }
> > +             res_xhciec = platform_get_resource(pdev, IORESOURCE_MEM, 1);
> >       }
> > -     priv->ini.ctrl_regs = devm_ioremap_resource(dev, res);
> > +     priv->ini.ctrl_regs = devm_ioremap_resource(dev, res_ctrl);
> >       if (IS_ERR(priv->ini.ctrl_regs)) {
> >               dev_err(dev, "can't map CTRL register space\n");
> >               return -EINVAL;
> >       }
> > -
> > -     /* The XHCI EC registers are optional */
> > -     res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
> > -     if (res) {
> > +     if (res_xhciec) {
> >               priv->ini.xhci_ec_regs =
> > -                     devm_ioremap_resource(dev, res);
> > +                     devm_ioremap_resource(dev, res_xhciec);
> >               if (IS_ERR(priv->ini.xhci_ec_regs)) {
> >                       dev_err(dev, "can't map XHCI EC register space\n");
> >                       return -EINVAL;
> >               }
> >       }
> > +     if (res_xhcigbl) {
> > +             priv->ini.xhci_gbl_regs =
> > +                     devm_ioremap_resource(dev, res_xhcigbl);
> > +             if (IS_ERR(priv->ini.xhci_gbl_regs)) {
> > +                     dev_err(dev, "can't map XHCI Global register space\n");
> > +                     return -EINVAL;
> > +             }
> > +     }
> >
> >       of_property_read_u32(dn, "brcm,ipp", &priv->ini.ipp);
> >       of_property_read_u32(dn, "brcm,ioc", &priv->ini.ioc);
> > @@ -480,11 +521,6 @@ static const struct dev_pm_ops brcm_usb_phy_pm_ops = {
> >       SET_LATE_SYSTEM_SLEEP_PM_OPS(brcm_usb_phy_suspend, brcm_usb_phy_resume)
> >  };
> >
> > -static const struct of_device_id brcm_usb_dt_ids[] = {
> > -     { .compatible = "brcm,brcmstb-usb-phy" },
> > -     { /* sentinel */ }
> > -};
> > -
> >  MODULE_DEVICE_TABLE(of, brcm_usb_dt_ids);
> >
> >  static struct platform_driver brcm_usb_driver = {
> >

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel