[PATCH 0/6] Add UHS mode support for TI's AM65x, J721e, J7200 boards

[PATCH 0/6] Add UHS mode support for TI's AM65x, J721e, J7200 boards

[Faiz Abbas]

The following are driver and documentation patches to enable UHS modes for
TI's AM65x, J721e, and J7200 boards. Device tree and defconfig patches
will be sent in a separate series.

With the complete set, the following maximum modes will be supported:

am654x-evm,idk		- SDR104, HS200
j721e-common-proc-board	- DDR50, HS200
j7200-common-proc-board	- DDR50, HS200

These patches mainly add support for the software tuning algorithm[1]
needed for higher speed modes

[1] [1] https://www.ti.com/lit/pdf/spract9

Faiz Abbas (6):
  dt-bindings: mmc: sdhci-am654: Convert sdhci-am654 controller
    documentation to json schema
  dt-bindings: mmc: sdhci-am654: Add documentation for input tap delay
  mmc: sdhci_am654: Fix hard coded otap delay array size
  mmc: sdhci_am654: Add support for input tap delay
  mmc: sdhci_am654: Add support for software tuning
  mmc: sdhci_am654: Enable tuning for SDR50

 .../devicetree/bindings/mmc/sdhci-am654.txt   |  65 ------
 .../devicetree/bindings/mmc/sdhci-am654.yaml  | 218 ++++++++++++++++++
 drivers/mmc/host/sdhci_am654.c                | 179 ++++++++++----
 3 files changed, 358 insertions(+), 104 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/mmc/sdhci-am654.txt
 create mode 100644 Documentation/devicetree/bindings/mmc/sdhci-am654.yaml

-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 1/6] dt-bindings: mmc: sdhci-am654: Convert sdhci-am654 controller documentation to json schema

[Faiz Abbas]

Convert sdhci-am654 documentation to yaml format. The new file
sdhci-am654.yaml will inherit from mmc-controller.yaml.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
---
 .../devicetree/bindings/mmc/sdhci-am654.txt   |  65 -------
 .../devicetree/bindings/mmc/sdhci-am654.yaml  | 175 ++++++++++++++++++
 2 files changed, 175 insertions(+), 65 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/mmc/sdhci-am654.txt
 create mode 100644 Documentation/devicetree/bindings/mmc/sdhci-am654.yaml

diff --git a/Documentation/devicetree/bindings/mmc/sdhci-am654.txt b/Documentation/devicetree/bindings/mmc/sdhci-am654.txt
deleted file mode 100644
index b49cbfdd679f..000000000000
--- a/Documentation/devicetree/bindings/mmc/sdhci-am654.txt
+++ /dev/null
@@ -1,65 +0,0 @@
-Device Tree Bindings for the SDHCI Controllers present on TI's AM654 SOCs
-
-The bindings follow the mmc[1], clock[2] and interrupt[3] bindings.
-Only deviations are documented here.
-
-  [1] Documentation/devicetree/bindings/mmc/mmc.txt
-  [2] Documentation/devicetree/bindings/clock/clock-bindings.txt
-  [3] Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
-
-Required Properties:
-	- compatible: should be one of:
-			"ti,am654-sdhci-5.1": SDHCI on AM654 device.
-			"ti,j721e-sdhci-8bit": 8 bit SDHCI on J721E device.
-			"ti,j721e-sdhci-4bit": 4 bit SDHCI on J721E device.
-			"ti,j7200-sdhci-8bit": 8 bit SDHCI on J7200 device.
-			"ti,j7200-sdhci-4bit": 4 bit SDHCI on J7200 device.
-	- reg: Must be two entries.
-		- The first should be the sdhci register space
-		- The second should the subsystem/phy register space
-	- clocks: Handles to the clock inputs.
-	- clock-names: Tuple including "clk_xin" and "clk_ahb"
-	- interrupts: Interrupt specifiers
-	Output tap delay for each speed mode:
-	- ti,otap-del-sel-legacy
-	- ti,otap-del-sel-mmc-hs
-	- ti,otap-del-sel-sd-hs
-	- ti,otap-del-sel-sdr12
-	- ti,otap-del-sel-sdr25
-	- ti,otap-del-sel-sdr50
-	- ti,otap-del-sel-sdr104
-	- ti,otap-del-sel-ddr50
-	- ti,otap-del-sel-ddr52
-	- ti,otap-del-sel-hs200
-	- ti,otap-del-sel-hs400
-	  These bindings must be provided otherwise the driver will disable the
-	  corresponding speed mode (i.e. all nodes must provide at least -legacy)
-
-Optional Properties (Required for ti,am654-sdhci-5.1,
-				  ti,j721e-sdhci-8bit,
-				  ti,j7200-sdhci-8bit):
-	- ti,trm-icp: DLL trim select
-	- ti,driver-strength-ohm: driver strength in ohms.
-				  Valid values are 33, 40, 50, 66 and 100 ohms.
-Optional Properties:
-	- ti,strobe-sel: strobe select delay for HS400 speed mode. Default value: 0x0.
-	- ti,clkbuf-sel: Clock Delay Buffer Select
-
-Example:
-
-	sdhci0: sdhci@4f80000 {
-		compatible = "ti,am654-sdhci-5.1";
-		reg = <0x0 0x4f80000 0x0 0x260>, <0x0 0x4f90000 0x0 0x134>;
-		power-domains = <&k3_pds 47>;
-		clocks = <&k3_clks 47 0>, <&k3_clks 47 1>;
-		clock-names = "clk_ahb", "clk_xin";
-		interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
-		sdhci-caps-mask = <0x80000007 0x0>;
-		mmc-ddr-1_8v;
-		ti,otap-del-sel-legacy = <0x0>;
-		ti,otap-del-sel-mmc-hs = <0x0>;
-		ti,otap-del-sel-ddr52 = <0x5>;
-		ti,otap-del-sel-hs200 = <0x5>;
-		ti,otap-del-sel-hs400 = <0x0>;
-		ti,trm-icp = <0x8>;
-	};
diff --git a/Documentation/devicetree/bindings/mmc/sdhci-am654.yaml b/Documentation/devicetree/bindings/mmc/sdhci-am654.yaml
new file mode 100644
index 000000000000..c222e057eca9
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/sdhci-am654.yaml
@@ -0,0 +1,175 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (C) 2020 Texas Instruments Incorporated - http://www.ti.com/
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/mmc/sdhci-am654.yaml#"
+$schema : "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: TI AM654 MMC Controller
+
+maintainers:
+  - Ulf Hansson <ulf.hansson@linaro.org>
+
+allOf:
+  - $ref: mmc-controller.yaml#
+
+properties:
+  compatible:
+    enum:
+      - ti,am654-sdhci-5.1
+      - ti,j721e-sdhci-8bit
+      - ti,j721e-sdhci-4bit
+      - ti,j7200-sdhci-8bit
+      - ti,j721e-sdhci-4bit
+
+  reg:
+    maxItems: 2
+
+  interrupts:
+    maxItems: 1
+
+  power-domains:
+    maxItems: 1
+
+  clocks:
+    minItems: 1
+    maxItems: 2
+    description: Handles to input clocks
+
+  clock-names:
+    minItems: 1
+    maxItems: 2
+    items:
+      - const: clk_ahb
+      - const: clk_xin
+
+  # PHY output tap delays:
+  # Used to delay the data valid window and align it to the sampling clock.
+  # Binding needs to be provided for each supported speed mode otherwise the
+  # corresponding mode will be disabled.
+
+  ti,otap-del-sel-legacy:
+    description: Output tap delay for SD/MMC legacy timing
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    minimum: 0
+    maximum: 0xf
+
+  ti,otap-del-sel-mmc-hs:
+    description: Output tap delay for MMC high speed timing
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    minimum: 0
+    maximum: 0xf
+
+  ti,otap-del-sel-sd-hs:
+    description: Output tap delay for SD high speed timing
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    minimum: 0
+    maximum: 0xf
+
+  ti,otap-del-sel-sdr12:
+    description: Output tap delay for SD UHS SDR12 timing
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    minimum: 0
+    maximum: 0xf
+
+  ti,otap-del-sel-sdr25:
+    description: Output tap delay for SD UHS SDR25 timing
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    minimum: 0
+    maximum: 0xf
+
+  ti,otap-del-sel-sdr50:
+    description: Output tap delay for SD UHS SDR50 timing
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    minimum: 0
+    maximum: 0xf
+
+  ti,otap-del-sel-sdr104:
+    description: Output tap delay for SD UHS SDR104 timing
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    minimum: 0
+    maximum: 0xf
+
+  ti,otap-del-sel-ddr50:
+    description: Output tap delay for SD UHS DDR50 timing
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    minimum: 0
+    maximum: 0xf
+
+  ti,otap-del-sel-ddr52:
+    description: Output tap delay for eMMC DDR52 timing
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    minimum: 0
+    maximum: 0xf
+
+  ti,otap-del-sel-hs200:
+    description: Output tap delay for eMMC HS200 timing
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    minimum: 0
+    maximum: 0xf
+
+  ti,otap-del-sel-hs400:
+    description: Output tap delay for eMMC HS400 timing
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    minimum: 0
+    maximum: 0xf
+
+  ti,trm-icp:
+    description: DLL trim select
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    minimum: 0
+    maximum: 0xf
+
+  ti,driver-strength-ohm:
+    description: DLL drive strength in ohms
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    oneOf:
+      - enum:
+        - 33
+        - 40
+        - 50
+        - 66
+        - 100
+
+  ti,strobe-sel:
+    description: strobe select delay for HS400 speed mode.
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+
+  ti,clkbuf-sel:
+    description: Clock Delay Buffer Select
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+  - ti,otap-del-sel-legacy
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    bus {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        mmc0: mmc@4f80000 {
+            compatible = "ti,am654-sdhci-5.1";
+            reg = <0x0 0x4f80000 0x0 0x260>, <0x0 0x4f90000 0x0 0x134>;
+            power-domains = <&k3_pds 47>;
+            clocks = <&k3_clks 47 0>, <&k3_clks 47 1>;
+            clock-names = "clk_ahb", "clk_xin";
+            interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
+            sdhci-caps-mask = <0x80000007 0x0>;
+            mmc-ddr-1_8v;
+            ti,otap-del-sel-legacy = <0x0>;
+            ti,otap-del-sel-mmc-hs = <0x0>;
+            ti,otap-del-sel-ddr52 = <0x5>;
+            ti,otap-del-sel-hs200 = <0x5>;
+            ti,otap-del-sel-hs400 = <0x0>;
+            ti,trm-icp = <0x8>;
+        };
+    };
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 2/6] dt-bindings: mmc: sdhci-am654: Add documentation for input tap delay

[Faiz Abbas]

Add documentation for input tap delay bindings.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
---
 .../devicetree/bindings/mmc/sdhci-am654.yaml  | 43 +++++++++++++++++++
 1 file changed, 43 insertions(+)

diff --git a/Documentation/devicetree/bindings/mmc/sdhci-am654.yaml b/Documentation/devicetree/bindings/mmc/sdhci-am654.yaml
index c222e057eca9..ac79f3adf20b 100644
--- a/Documentation/devicetree/bindings/mmc/sdhci-am654.yaml
+++ b/Documentation/devicetree/bindings/mmc/sdhci-am654.yaml
@@ -114,6 +114,46 @@ properties:
     minimum: 0
     maximum: 0xf
 
+  # PHY input tap delays:
+  # Used to delay the data valid window and align it to the sampling clock for
+  # modes that don't support tuning
+
+  ti,itap-del-sel-legacy:
+    description: Input tap delay for SD/MMC legacy timing
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    minimum: 0
+    maximum: 0x1f
+
+  ti,itap-del-sel-mmc-hs:
+    description: Input tap delay for MMC high speed timing
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    minimum: 0
+    maximum: 0x1f
+
+  ti,itap-del-sel-sd-hs:
+    description: Input tap delay for SD high speed timing
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    minimum: 0
+    maximum: 0x1f
+
+  ti,itap-del-sel-sdr12:
+    description: Input tap delay for SD UHS SDR12 timing
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    minimum: 0
+    maximum: 0x1f
+
+  ti,itap-del-sel-sdr25:
+    description: Input tap delay for SD UHS SDR25 timing
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    minimum: 0
+    maximum: 0x1f
+
+  ti,itap-del-sel-ddr52:
+    description: Input tap delay for MMC DDR52 timing
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    minimum: 0
+    maximum: 0x1f
+
   ti,trm-icp:
     description: DLL trim select
     $ref: "/schemas/types.yaml#/definitions/uint32"
@@ -170,6 +210,9 @@ examples:
             ti,otap-del-sel-ddr52 = <0x5>;
             ti,otap-del-sel-hs200 = <0x5>;
             ti,otap-del-sel-hs400 = <0x0>;
+            ti,itap-del-sel-legacy = <0x10>;
+            ti,itap-del-sel-mmc-hs = <0xa>;
+            ti,itap-del-sel-ddr52 = <0x3>;
             ti,trm-icp = <0x8>;
         };
     };
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 3/6] mmc: sdhci_am654: Fix hard coded otap delay array size

[Faiz Abbas]

Change hard coded array size value to depend on struct timing_data
array size.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
---
 drivers/mmc/host/sdhci_am654.c | 42 +++++++++++++++++-----------------
 1 file changed, 21 insertions(+), 21 deletions(-)

diff --git a/drivers/mmc/host/sdhci_am654.c b/drivers/mmc/host/sdhci_am654.c
index a4c6d9d80e88..9f3347bc3757 100644
--- a/drivers/mmc/host/sdhci_am654.c
+++ b/drivers/mmc/host/sdhci_am654.c
@@ -85,10 +85,30 @@ static struct regmap_config sdhci_am654_regmap_config = {
 	.fast_io = true,
 };
 
+struct timing_data {
+	const char *binding;
+	u32 capability;
+};
+
+static const struct timing_data td[] = {
+	[MMC_TIMING_LEGACY] = {"ti,otap-del-sel-legacy", 0},
+	[MMC_TIMING_MMC_HS] = {"ti,otap-del-sel-mmc-hs", MMC_CAP_MMC_HIGHSPEED},
+	[MMC_TIMING_SD_HS]  = {"ti,otap-del-sel-sd-hs", MMC_CAP_SD_HIGHSPEED},
+	[MMC_TIMING_UHS_SDR12] = {"ti,otap-del-sel-sdr12", MMC_CAP_UHS_SDR12},
+	[MMC_TIMING_UHS_SDR25] = {"ti,otap-del-sel-sdr25", MMC_CAP_UHS_SDR25},
+	[MMC_TIMING_UHS_SDR50] = {"ti,otap-del-sel-sdr50", MMC_CAP_UHS_SDR50},
+	[MMC_TIMING_UHS_SDR104] = {"ti,otap-del-sel-sdr104",
+				   MMC_CAP_UHS_SDR104},
+	[MMC_TIMING_UHS_DDR50] = {"ti,otap-del-sel-ddr50", MMC_CAP_UHS_DDR50},
+	[MMC_TIMING_MMC_DDR52] = {"ti,otap-del-sel-ddr52", MMC_CAP_DDR},
+	[MMC_TIMING_MMC_HS200] = {"ti,otap-del-sel-hs200", MMC_CAP2_HS200},
+	[MMC_TIMING_MMC_HS400] = {"ti,otap-del-sel-hs400", MMC_CAP2_HS400},
+};
+
 struct sdhci_am654_data {
 	struct regmap *base;
 	bool legacy_otapdly;
-	int otap_del_sel[11];
+	int otap_del_sel[ARRAY_SIZE(td)];
 	int clkbuf_sel;
 	int trm_icp;
 	int drv_strength;
@@ -107,26 +127,6 @@ struct sdhci_am654_driver_data {
 #define DLL_CALIB	(1 << 4)
 };
 
-struct timing_data {
-	const char *binding;
-	u32 capability;
-};
-
-static const struct timing_data td[] = {
-	[MMC_TIMING_LEGACY] = {"ti,otap-del-sel-legacy", 0},
-	[MMC_TIMING_MMC_HS] = {"ti,otap-del-sel-mmc-hs", MMC_CAP_MMC_HIGHSPEED},
-	[MMC_TIMING_SD_HS]  = {"ti,otap-del-sel-sd-hs", MMC_CAP_SD_HIGHSPEED},
-	[MMC_TIMING_UHS_SDR12] = {"ti,otap-del-sel-sdr12", MMC_CAP_UHS_SDR12},
-	[MMC_TIMING_UHS_SDR25] = {"ti,otap-del-sel-sdr25", MMC_CAP_UHS_SDR25},
-	[MMC_TIMING_UHS_SDR50] = {"ti,otap-del-sel-sdr50", MMC_CAP_UHS_SDR50},
-	[MMC_TIMING_UHS_SDR104] = {"ti,otap-del-sel-sdr104",
-				   MMC_CAP_UHS_SDR104},
-	[MMC_TIMING_UHS_DDR50] = {"ti,otap-del-sel-ddr50", MMC_CAP_UHS_DDR50},
-	[MMC_TIMING_MMC_DDR52] = {"ti,otap-del-sel-ddr52", MMC_CAP_DDR},
-	[MMC_TIMING_MMC_HS200] = {"ti,otap-del-sel-hs200", MMC_CAP2_HS200},
-	[MMC_TIMING_MMC_HS400] = {"ti,otap-del-sel-hs400", MMC_CAP2_HS400},
-};
-
 static void sdhci_am654_setup_dll(struct sdhci_host *host, unsigned int clock)
 {
 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 4/6] mmc: sdhci_am654: Add support for input tap delay

[Faiz Abbas]

DLL need only be enabled for speed modes and clock frequencies at or
above 50 MHz. For speed modes that don't enable the DLL, we need to
configure a static input delay value. This involves reading an optional
itap-del-sel-* value from the device tree and configuring it for the
appropriate speed mode.

With this addition, make sure that DLL is always switched off at the
beginning of the set_clock() call to simplify configuration. This also
removes the need for the dll_on member in struct sdhci_am654_data.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
---
 drivers/mmc/host/sdhci_am654.c | 114 ++++++++++++++++++++++++---------
 1 file changed, 84 insertions(+), 30 deletions(-)

diff --git a/drivers/mmc/host/sdhci_am654.c b/drivers/mmc/host/sdhci_am654.c
index 9f3347bc3757..1213b711e60a 100644
--- a/drivers/mmc/host/sdhci_am654.c
+++ b/drivers/mmc/host/sdhci_am654.c
@@ -66,6 +66,14 @@
 #define RETRIM_MASK		BIT(RETRIM_SHIFT)
 #define SELDLYTXCLK_SHIFT	17
 #define SELDLYTXCLK_MASK	BIT(SELDLYTXCLK_SHIFT)
+#define SELDLYRXCLK_SHIFT	16
+#define SELDLYRXCLK_MASK	BIT(SELDLYRXCLK_SHIFT)
+#define ITAPDLYSEL_SHIFT	0
+#define ITAPDLYSEL_MASK		GENMASK(4, 0)
+#define ITAPDLYENA_SHIFT	8
+#define ITAPDLYENA_MASK		BIT(ITAPDLYENA_SHIFT)
+#define ITAPCHGWIN_SHIFT	9
+#define ITAPCHGWIN_MASK		BIT(ITAPCHGWIN_SHIFT)
 
 #define DRIVER_STRENGTH_50_OHM	0x0
 #define DRIVER_STRENGTH_33_OHM	0x1
@@ -73,7 +81,7 @@
 #define DRIVER_STRENGTH_100_OHM	0x3
 #define DRIVER_STRENGTH_40_OHM	0x4
 
-#define CLOCK_TOO_SLOW_HZ	400000
+#define CLOCK_TOO_SLOW_HZ	50000000
 
 /* Command Queue Host Controller Interface Base address */
 #define SDHCI_AM654_CQE_BASE_ADDR 0x200
@@ -86,33 +94,55 @@ static struct regmap_config sdhci_am654_regmap_config = {
 };
 
 struct timing_data {
-	const char *binding;
+	const char *otap_binding;
+	const char *itap_binding;
 	u32 capability;
 };
 
 static const struct timing_data td[] = {
-	[MMC_TIMING_LEGACY] = {"ti,otap-del-sel-legacy", 0},
-	[MMC_TIMING_MMC_HS] = {"ti,otap-del-sel-mmc-hs", MMC_CAP_MMC_HIGHSPEED},
-	[MMC_TIMING_SD_HS]  = {"ti,otap-del-sel-sd-hs", MMC_CAP_SD_HIGHSPEED},
-	[MMC_TIMING_UHS_SDR12] = {"ti,otap-del-sel-sdr12", MMC_CAP_UHS_SDR12},
-	[MMC_TIMING_UHS_SDR25] = {"ti,otap-del-sel-sdr25", MMC_CAP_UHS_SDR25},
-	[MMC_TIMING_UHS_SDR50] = {"ti,otap-del-sel-sdr50", MMC_CAP_UHS_SDR50},
-	[MMC_TIMING_UHS_SDR104] = {"ti,otap-del-sel-sdr104",
+	[MMC_TIMING_LEGACY]	= {"ti,otap-del-sel-legacy",
+				   "ti,itap-del-sel-legacy",
+				   0},
+	[MMC_TIMING_MMC_HS]	= {"ti,otap-del-sel-mmc-hs",
+				   "ti,itap-del-sel-mmc-hs",
+				   MMC_CAP_MMC_HIGHSPEED},
+	[MMC_TIMING_SD_HS]	= {"ti,otap-del-sel-sd-hs",
+				   "ti,itap-del-sel-sd-hs",
+				   MMC_CAP_SD_HIGHSPEED},
+	[MMC_TIMING_UHS_SDR12]	= {"ti,otap-del-sel-sdr12",
+				   "ti,itap-del-sel-sdr12",
+				   MMC_CAP_UHS_SDR12},
+	[MMC_TIMING_UHS_SDR25]	= {"ti,otap-del-sel-sdr25",
+				   "ti,itap-del-sel-sdr25",
+				   MMC_CAP_UHS_SDR25},
+	[MMC_TIMING_UHS_SDR50]	= {"ti,otap-del-sel-sdr50",
+				   NULL,
+				   MMC_CAP_UHS_SDR50},
+	[MMC_TIMING_UHS_SDR104]	= {"ti,otap-del-sel-sdr104",
+				   NULL,
 				   MMC_CAP_UHS_SDR104},
-	[MMC_TIMING_UHS_DDR50] = {"ti,otap-del-sel-ddr50", MMC_CAP_UHS_DDR50},
-	[MMC_TIMING_MMC_DDR52] = {"ti,otap-del-sel-ddr52", MMC_CAP_DDR},
-	[MMC_TIMING_MMC_HS200] = {"ti,otap-del-sel-hs200", MMC_CAP2_HS200},
-	[MMC_TIMING_MMC_HS400] = {"ti,otap-del-sel-hs400", MMC_CAP2_HS400},
+	[MMC_TIMING_UHS_DDR50]	= {"ti,otap-del-sel-ddr50",
+				   NULL,
+				   MMC_CAP_UHS_DDR50},
+	[MMC_TIMING_MMC_DDR52]	= {"ti,otap-del-sel-ddr52",
+				   "ti,itap-del-sel-ddr52",
+				   MMC_CAP_DDR},
+	[MMC_TIMING_MMC_HS200]	= {"ti,otap-del-sel-hs200",
+				   NULL,
+				   MMC_CAP2_HS200},
+	[MMC_TIMING_MMC_HS400]	= {"ti,otap-del-sel-hs400",
+				   NULL,
+				   MMC_CAP2_HS400},
 };
 
 struct sdhci_am654_data {
 	struct regmap *base;
 	bool legacy_otapdly;
 	int otap_del_sel[ARRAY_SIZE(td)];
+	int itap_del_sel[ARRAY_SIZE(td)];
 	int clkbuf_sel;
 	int trm_icp;
 	int drv_strength;
-	bool dll_on;
 	int strb_sel;
 	u32 flags;
 };
@@ -135,6 +165,10 @@ static void sdhci_am654_setup_dll(struct sdhci_host *host, unsigned int clock)
 	u32 mask, val;
 	int ret;
 
+	/* Disable delay chain mode */
+	regmap_update_bits(sdhci_am654->base, PHY_CTRL5,
+			   SELDLYTXCLK_MASK | SELDLYRXCLK_MASK, 0);
+
 	if (sdhci_am654->flags & FREQSEL_2_BIT) {
 		switch (clock) {
 		case 200000000:
@@ -189,8 +223,32 @@ static void sdhci_am654_setup_dll(struct sdhci_host *host, unsigned int clock)
 		dev_err(mmc_dev(host->mmc), "DLL failed to relock\n");
 		return;
 	}
+}
+
+static void sdhci_am654_write_itapdly(struct sdhci_am654_data *sdhci_am654,
+				      u32 itapdly)
+{
+	/* Set ITAPCHGWIN before writing to ITAPDLY */
+	regmap_update_bits(sdhci_am654->base, PHY_CTRL4, ITAPCHGWIN_MASK,
+			   1 << ITAPCHGWIN_SHIFT);
+	regmap_update_bits(sdhci_am654->base, PHY_CTRL4, ITAPDLYSEL_MASK,
+			   itapdly << ITAPDLYSEL_SHIFT);
+	regmap_update_bits(sdhci_am654->base, PHY_CTRL4, ITAPCHGWIN_MASK, 0);
+}
+
+static void sdhci_am654_setup_delay_chain(struct sdhci_am654_data *sdhci_am654,
+					  unsigned char timing)
+{
+	u32 mask, val;
 
-	sdhci_am654->dll_on = true;
+	regmap_update_bits(sdhci_am654->base, PHY_CTRL1, ENDLL_MASK, 0);
+
+	val = 1 << SELDLYTXCLK_SHIFT | 1 << SELDLYRXCLK_SHIFT;
+	mask = SELDLYTXCLK_MASK | SELDLYRXCLK_MASK;
+	regmap_update_bits(sdhci_am654->base, PHY_CTRL5, mask, val);
+
+	sdhci_am654_write_itapdly(sdhci_am654,
+				  sdhci_am654->itap_del_sel[timing]);
 }
 
 static void sdhci_am654_set_clock(struct sdhci_host *host, unsigned int clock)
@@ -202,11 +260,7 @@ static void sdhci_am654_set_clock(struct sdhci_host *host, unsigned int clock)
 	u32 otap_del_ena;
 	u32 mask, val;
 
-	if (sdhci_am654->dll_on) {
-		regmap_update_bits(sdhci_am654->base, PHY_CTRL1, ENDLL_MASK, 0);
-
-		sdhci_am654->dll_on = false;
-	}
+	regmap_update_bits(sdhci_am654->base, PHY_CTRL1, ENDLL_MASK, 0);
 
 	sdhci_set_clock(host, clock);
 
@@ -234,14 +288,10 @@ static void sdhci_am654_set_clock(struct sdhci_host *host, unsigned int clock)
 
 	regmap_update_bits(sdhci_am654->base, PHY_CTRL4, mask, val);
 
-	if (timing > MMC_TIMING_UHS_SDR25 && clock > CLOCK_TOO_SLOW_HZ) {
-		regmap_update_bits(sdhci_am654->base, PHY_CTRL5,
-				   SELDLYTXCLK_MASK, 0);
+	if (timing > MMC_TIMING_UHS_SDR25 && clock >= CLOCK_TOO_SLOW_HZ)
 		sdhci_am654_setup_dll(host, clock);
-	} else {
-		regmap_update_bits(sdhci_am654->base, PHY_CTRL5,
-				   SELDLYTXCLK_MASK, 1 << SELDLYTXCLK_SHIFT);
-	}
+	else
+		sdhci_am654_setup_delay_chain(sdhci_am654, timing);
 
 	regmap_update_bits(sdhci_am654->base, PHY_CTRL5, CLKBUFSEL_MASK,
 			   sdhci_am654->clkbuf_sel);
@@ -469,7 +519,7 @@ static int sdhci_am654_get_otap_delay(struct sdhci_host *host,
 	int i;
 	int ret;
 
-	ret = device_property_read_u32(dev, td[MMC_TIMING_LEGACY].binding,
+	ret = device_property_read_u32(dev, td[MMC_TIMING_LEGACY].otap_binding,
 				 &sdhci_am654->otap_del_sel[MMC_TIMING_LEGACY]);
 	if (ret) {
 		/*
@@ -492,11 +542,11 @@ static int sdhci_am654_get_otap_delay(struct sdhci_host *host,
 
 	for (i = MMC_TIMING_MMC_HS; i <= MMC_TIMING_MMC_HS400; i++) {
 
-		ret = device_property_read_u32(dev, td[i].binding,
+		ret = device_property_read_u32(dev, td[i].otap_binding,
 					       &sdhci_am654->otap_del_sel[i]);
 		if (ret) {
 			dev_dbg(dev, "Couldn't find %s\n",
-				td[i].binding);
+				td[i].otap_binding);
 			/*
 			 * Remove the corresponding capability
 			 * if an otap-del-sel value is not found
@@ -506,6 +556,10 @@ static int sdhci_am654_get_otap_delay(struct sdhci_host *host,
 			else
 				host->mmc->caps2 &= ~td[i].capability;
 		}
+
+		if (td[i].itap_binding)
+			device_property_read_u32(dev, td[i].itap_binding,
+						 &sdhci_am654->itap_del_sel[i]);
 	}
 
 	return 0;
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 5/6] mmc: sdhci_am654: Add support for software tuning

[Faiz Abbas]

With the new SW tuning App note[1], a custom tuning algorithm is
required for eMMC HS200, HS400 and SD card UHS modes. The algorithm
involves running through the 32 possible input tap delay values and
sending the appropriate tuning command (CMD19/21) for each of them
to get a fail or pass result for each of the values. Typically, the
range will have a small contiguous failing window. Considering the
tuning range as a circular buffer, the algorithm then sets a final
tuned value directly opposite to the failing window.

[1] https://www.ti.com/lit/pdf/spract9

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
---
 drivers/mmc/host/sdhci_am654.c | 41 ++++++++++++++++++++++++++++++++++
 1 file changed, 41 insertions(+)

diff --git a/drivers/mmc/host/sdhci_am654.c b/drivers/mmc/host/sdhci_am654.c
index 1213b711e60a..5af7638ad606 100644
--- a/drivers/mmc/host/sdhci_am654.c
+++ b/drivers/mmc/host/sdhci_am654.c
@@ -396,7 +396,46 @@ static u32 sdhci_am654_cqhci_irq(struct sdhci_host *host, u32 intmask)
 	return 0;
 }
 
+#define ITAP_MAX	32
+static int sdhci_am654_platform_execute_tuning(struct sdhci_host *host,
+					       u32 opcode)
+{
+	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+	struct sdhci_am654_data *sdhci_am654 = sdhci_pltfm_priv(pltfm_host);
+	int cur_val, prev_val = 1, fail_len = 0, pass_window = 0, pass_len;
+	u32 itap;
+
+	/* Enable ITAPDLY */
+	regmap_update_bits(sdhci_am654->base, PHY_CTRL4, ITAPDLYENA_MASK,
+			   1 << ITAPDLYENA_SHIFT);
+
+	for (itap = 0; itap < ITAP_MAX; itap++) {
+		sdhci_am654_write_itapdly(sdhci_am654, itap);
+
+		cur_val = !mmc_send_tuning(host->mmc, opcode, NULL);
+		if (cur_val && !prev_val)
+			pass_window = itap;
+
+		if (!cur_val)
+			fail_len++;
+
+		prev_val = cur_val;
+	}
+	/*
+	 * Having determined the length of the failing window and start of
+	 * the passing window calculate the length of the passing window and
+	 * set the final value halfway through it considering the range as a
+	 * circular buffer
+	 */
+	pass_len = ITAP_MAX - fail_len;
+	itap = (pass_window + (pass_len >> 1)) % ITAP_MAX;
+	sdhci_am654_write_itapdly(sdhci_am654, itap);
+
+	return 0;
+}
+
 static struct sdhci_ops sdhci_am654_ops = {
+	.platform_execute_tuning = sdhci_am654_platform_execute_tuning,
 	.get_max_clock = sdhci_pltfm_clk_get_max_clock,
 	.get_timeout_clock = sdhci_pltfm_clk_get_max_clock,
 	.set_uhs_signaling = sdhci_set_uhs_signaling,
@@ -426,6 +465,7 @@ static const struct sdhci_am654_driver_data sdhci_am654_drvdata = {
 };
 
 static struct sdhci_ops sdhci_j721e_8bit_ops = {
+	.platform_execute_tuning = sdhci_am654_platform_execute_tuning,
 	.get_max_clock = sdhci_pltfm_clk_get_max_clock,
 	.get_timeout_clock = sdhci_pltfm_clk_get_max_clock,
 	.set_uhs_signaling = sdhci_set_uhs_signaling,
@@ -449,6 +489,7 @@ static const struct sdhci_am654_driver_data sdhci_j721e_8bit_drvdata = {
 };
 
 static struct sdhci_ops sdhci_j721e_4bit_ops = {
+	.platform_execute_tuning = sdhci_am654_platform_execute_tuning,
 	.get_max_clock = sdhci_pltfm_clk_get_max_clock,
 	.get_timeout_clock = sdhci_pltfm_clk_get_max_clock,
 	.set_uhs_signaling = sdhci_set_uhs_signaling,
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 6/6] mmc: sdhci_am654: Enable tuning for SDR50

[Faiz Abbas]

According to the SW tuning App note[1], tuning is required for all
UHS speed modes. Tuning for SDR50 is not enabled in Capabilities by
default so enable it from the CTL_CFG registers.

[1] https://www.ti.com/lit/pdf/spract9

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
---
 drivers/mmc/host/sdhci_am654.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/drivers/mmc/host/sdhci_am654.c b/drivers/mmc/host/sdhci_am654.c
index 5af7638ad606..2bce962bf7e4 100644
--- a/drivers/mmc/host/sdhci_am654.c
+++ b/drivers/mmc/host/sdhci_am654.c
@@ -19,9 +19,11 @@
 
 /* CTL_CFG Registers */
 #define CTL_CFG_2		0x14
+#define CTL_CFG_3		0x18
 
 #define SLOTTYPE_MASK		GENMASK(31, 30)
 #define SLOTTYPE_EMBEDDED	BIT(30)
+#define TUNINGFORSDR50_MASK	BIT(13)
 
 /* PHY Registers */
 #define PHY_CTRL1	0x100
@@ -646,6 +648,10 @@ static int sdhci_am654_init(struct sdhci_host *host)
 	regmap_update_bits(sdhci_am654->base, CTL_CFG_2, SLOTTYPE_MASK,
 			   ctl_cfg_2);
 
+	/* Enable tuning for SDR50 */
+	regmap_update_bits(sdhci_am654->base, CTL_CFG_3, TUNINGFORSDR50_MASK,
+			   TUNINGFORSDR50_MASK);
+
 	ret = sdhci_setup_host(host);
 	if (ret)
 		return ret;
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 5/6] mmc: sdhci_am654: Add support for software tuning

[Kishon Vijay Abraham I]

On 23/09/20 4:22 pm, Faiz Abbas wrote:
> With the new SW tuning App note[1], a custom tuning algorithm is
> required for eMMC HS200, HS400 and SD card UHS modes. The algorithm
> involves running through the 32 possible input tap delay values and
> sending the appropriate tuning command (CMD19/21) for each of them
> to get a fail or pass result for each of the values. Typically, the
> range will have a small contiguous failing window. Considering the
> tuning range as a circular buffer, the algorithm then sets a final
> tuned value directly opposite to the failing window.
> 
> [1] https://www.ti.com/lit/pdf/spract9
> 
> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>

Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
> ---
>  drivers/mmc/host/sdhci_am654.c | 41 ++++++++++++++++++++++++++++++++++
>  1 file changed, 41 insertions(+)
> 
> diff --git a/drivers/mmc/host/sdhci_am654.c b/drivers/mmc/host/sdhci_am654.c
> index 1213b711e60a..5af7638ad606 100644
> --- a/drivers/mmc/host/sdhci_am654.c
> +++ b/drivers/mmc/host/sdhci_am654.c
> @@ -396,7 +396,46 @@ static u32 sdhci_am654_cqhci_irq(struct sdhci_host *host, u32 intmask)
>  	return 0;
>  }
>  
> +#define ITAP_MAX	32
> +static int sdhci_am654_platform_execute_tuning(struct sdhci_host *host,
> +					       u32 opcode)
> +{
> +	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> +	struct sdhci_am654_data *sdhci_am654 = sdhci_pltfm_priv(pltfm_host);
> +	int cur_val, prev_val = 1, fail_len = 0, pass_window = 0, pass_len;
> +	u32 itap;
> +
> +	/* Enable ITAPDLY */
> +	regmap_update_bits(sdhci_am654->base, PHY_CTRL4, ITAPDLYENA_MASK,
> +			   1 << ITAPDLYENA_SHIFT);
> +
> +	for (itap = 0; itap < ITAP_MAX; itap++) {
> +		sdhci_am654_write_itapdly(sdhci_am654, itap);
> +
> +		cur_val = !mmc_send_tuning(host->mmc, opcode, NULL);
> +		if (cur_val && !prev_val)
> +			pass_window = itap;
> +
> +		if (!cur_val)
> +			fail_len++;
> +
> +		prev_val = cur_val;
> +	}
> +	/*
> +	 * Having determined the length of the failing window and start of
> +	 * the passing window calculate the length of the passing window and
> +	 * set the final value halfway through it considering the range as a
> +	 * circular buffer
> +	 */
> +	pass_len = ITAP_MAX - fail_len;
> +	itap = (pass_window + (pass_len >> 1)) % ITAP_MAX;
> +	sdhci_am654_write_itapdly(sdhci_am654, itap);
> +
> +	return 0;
> +}
> +
>  static struct sdhci_ops sdhci_am654_ops = {
> +	.platform_execute_tuning = sdhci_am654_platform_execute_tuning,
>  	.get_max_clock = sdhci_pltfm_clk_get_max_clock,
>  	.get_timeout_clock = sdhci_pltfm_clk_get_max_clock,
>  	.set_uhs_signaling = sdhci_set_uhs_signaling,
> @@ -426,6 +465,7 @@ static const struct sdhci_am654_driver_data sdhci_am654_drvdata = {
>  };
>  
>  static struct sdhci_ops sdhci_j721e_8bit_ops = {
> +	.platform_execute_tuning = sdhci_am654_platform_execute_tuning,
>  	.get_max_clock = sdhci_pltfm_clk_get_max_clock,
>  	.get_timeout_clock = sdhci_pltfm_clk_get_max_clock,
>  	.set_uhs_signaling = sdhci_set_uhs_signaling,
> @@ -449,6 +489,7 @@ static const struct sdhci_am654_driver_data sdhci_j721e_8bit_drvdata = {
>  };
>  
>  static struct sdhci_ops sdhci_j721e_4bit_ops = {
> +	.platform_execute_tuning = sdhci_am654_platform_execute_tuning,
>  	.get_max_clock = sdhci_pltfm_clk_get_max_clock,
>  	.get_timeout_clock = sdhci_pltfm_clk_get_max_clock,
>  	.set_uhs_signaling = sdhci_set_uhs_signaling,
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 0/6] Add UHS mode support for TI's AM65x, J721e, J7200 boards

[Ulf Hansson]

On Wed, 23 Sep 2020 at 12:52, Faiz Abbas <faiz_abbas@ti.com> wrote:
>
> The following are driver and documentation patches to enable UHS modes for
> TI's AM65x, J721e, and J7200 boards. Device tree and defconfig patches
> will be sent in a separate series.
>
> With the complete set, the following maximum modes will be supported:
>
> am654x-evm,idk          - SDR104, HS200
> j721e-common-proc-board - DDR50, HS200
> j7200-common-proc-board - DDR50, HS200
>
> These patches mainly add support for the software tuning algorithm[1]
> needed for higher speed modes
>
> [1] [1] https://www.ti.com/lit/pdf/spract9
>
> Faiz Abbas (6):
>   dt-bindings: mmc: sdhci-am654: Convert sdhci-am654 controller
>     documentation to json schema
>   dt-bindings: mmc: sdhci-am654: Add documentation for input tap delay
>   mmc: sdhci_am654: Fix hard coded otap delay array size
>   mmc: sdhci_am654: Add support for input tap delay
>   mmc: sdhci_am654: Add support for software tuning
>   mmc: sdhci_am654: Enable tuning for SDR50
>
>  .../devicetree/bindings/mmc/sdhci-am654.txt   |  65 ------
>  .../devicetree/bindings/mmc/sdhci-am654.yaml  | 218 ++++++++++++++++++
>  drivers/mmc/host/sdhci_am654.c                | 179 ++++++++++----
>  3 files changed, 358 insertions(+), 104 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/mmc/sdhci-am654.txt
>  create mode 100644 Documentation/devicetree/bindings/mmc/sdhci-am654.yaml
>
> --
> 2.17.1
>

Applied for next, thanks!

Kind regards
Uffe

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel