[PATCH net-next 0/2] Introducing support for DWC xpcs Energy Efficient Ethernet

[PATCH net-next 0/2] Introducing support for DWC xpcs Energy Efficient Ethernet

[Michael Sit Wei Hong]

The goal of this patch set is to enable EEE in the xpcs so that when
EEE is enabled, the MAC-->xpcs-->PHY have all the EEE related
configurations enabled.

Patch 1 adds the functions to enable EEE in the xpcs and sets it to
transparent mode.
Patch 2 adds the callbacks to configure the xpcs EEE mode.

The results are tested by checking the lpi counters of the tx and rx
path of the interface. When EEE is enabled, the lpi counters should
increament as it enters and exits lpi states.

host@EHL$ ethtool --show-eee enp0s30f4
EEE Settings for enp0s30f4:
        EEE status: disabled
        Tx LPI: disabled
        Supported EEE link modes:  100baseT/Full
                                   1000baseT/Full
        Advertised EEE link modes:  Not reported
        Link partner advertised EEE link modes:  100baseT/Full
                                                 1000baseT/Full
host@EHL$ ethtool -S enp0s30f4 | grep lpi
     irq_tx_path_in_lpi_mode_n: 0
     irq_tx_path_exit_lpi_mode_n: 0
     irq_rx_path_in_lpi_mode_n: 0
     irq_rx_path_exit_lpi_mode_n: 0
host@EHL$ ethtool --set-eee enp0s30f4 eee on
host@EHL$ [  110.265154] intel-eth-pci 0000:00:1e.4 enp0s30f4: Link is Down
[  112.315155] intel-eth-pci 0000:00:1e.4 enp0s30f4: Link is Up - 1Gbps/Full - flow control off
[  112.324612] IPv6: ADDRCONF(NETDEV_CHANGE): enp0s30f4: link becomes ready
host@EHL$ ethtool --show-eee enp0s30f4
EEE Settings for enp0s30f4:
        EEE status: enabled - active
        Tx LPI: 1000000 (us)
        Supported EEE link modes:  100baseT/Full
                                   1000baseT/Full
        Advertised EEE link modes:  100baseT/Full
                                    1000baseT/Full
        Link partner advertised EEE link modes:  100baseT/Full
                                                 1000baseT/Full
host@EHL$ ethtool -S enp0s30f4 | grep lpi
     irq_tx_path_in_lpi_mode_n: 6
     irq_tx_path_exit_lpi_mode_n: 5
     irq_rx_path_in_lpi_mode_n: 7
     irq_rx_path_exit_lpi_mode_n: 6
host@EHL$ ping 192.168.1.1
PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=1.02 ms
64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=0.510 ms
64 bytes from 192.168.1.1: icmp_seq=3 ttl=64 time=0.489 ms
64 bytes from 192.168.1.1: icmp_seq=4 ttl=64 time=0.484 ms
64 bytes from 192.168.1.1: icmp_seq=5 ttl=64 time=0.504 ms
64 bytes from 192.168.1.1: icmp_seq=6 ttl=64 time=0.466 ms
64 bytes from 192.168.1.1: icmp_seq=7 ttl=64 time=0.529 ms
64 bytes from 192.168.1.1: icmp_seq=8 ttl=64 time=0.519 ms
64 bytes from 192.168.1.1: icmp_seq=9 ttl=64 time=0.518 ms
64 bytes from 192.168.1.1: icmp_seq=10 ttl=64 time=0.501 ms

--- 192.168.1.1 ping statistics ---
10 packets transmitted, 10 received, 0% packet loss, time 9216ms
rtt min/avg/max/mdev = 0.466/0.553/1.018/0.155 ms
host@EHL$ ethtool -S enp0s30f4 | grep lpi
     irq_tx_path_in_lpi_mode_n: 22
     irq_tx_path_exit_lpi_mode_n: 21
     irq_rx_path_in_lpi_mode_n: 21
     irq_rx_path_exit_lpi_mode_n: 20

Michael Sit Wei Hong (2):
  net: pcs: Introducing support for DWC xpcs Energy Efficient Ethernet
  net: stmmac: Add callbacks for DWC xpcs Energy Efficient Ethernet

 .../net/ethernet/stmicro/stmmac/dwmac-intel.c | 11 ++++
 drivers/net/ethernet/stmicro/stmmac/hwif.h    |  2 +
 .../ethernet/stmicro/stmmac/stmmac_ethtool.c  |  6 +++
 drivers/net/pcs/pcs-xpcs.c                    | 51 +++++++++++++++++++
 include/linux/pcs/pcs-xpcs.h                  |  2 +
 include/linux/stmmac.h                        |  1 +
 6 files changed, 73 insertions(+)

-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH net-next 1/2] net: pcs: Introducing support for DWC xpcs Energy Efficient Ethernet

[Michael Sit Wei Hong]

Add DWC xpcs EEE support callbacks.The callback function is used to
set EEE registers on xpcs.

xpcs transparent mode is enabled to allow PHY to detect MAC EEE status.

Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
---
 drivers/net/pcs/pcs-xpcs.c   | 51 ++++++++++++++++++++++++++++++++++++
 include/linux/pcs/pcs-xpcs.h |  2 ++
 2 files changed, 53 insertions(+)

diff --git a/drivers/net/pcs/pcs-xpcs.c b/drivers/net/pcs/pcs-xpcs.c
index 944ba105cac1..aa985a5aae8d 100644
--- a/drivers/net/pcs/pcs-xpcs.c
+++ b/drivers/net/pcs/pcs-xpcs.c
@@ -63,6 +63,9 @@
 #define DW_VR_MII_DIG_CTRL1		0x8000
 #define DW_VR_MII_AN_CTRL		0x8001
 #define DW_VR_MII_AN_INTR_STS		0x8002
+/* EEE Mode Control Register */
+#define DW_VR_MII_EEE_MCTRL0		0x8006
+#define DW_VR_MII_EEE_MCTRL1		0x800b
 
 /* VR_MII_DIG_CTRL1 */
 #define DW_VR_MII_DIG_CTRL1_MAC_AUTO_SW		BIT(9)
@@ -86,6 +89,20 @@
 #define DW_VR_MII_C37_ANSGM_SP_1000		0x2
 #define DW_VR_MII_C37_ANSGM_SP_LNKSTS		BIT(4)
 
+/* VR MII EEE Control 0 defines */
+#define DW_VR_MII_EEE_LTX_EN		BIT(0)  /* LPI Tx Enable */
+#define DW_VR_MII_EEE_LRX_EN		BIT(1)  /* LPI Rx Enable */
+#define DW_VR_MII_EEE_TX_QUIET_EN		BIT(2)  /* Tx Quiet Enable */
+#define DW_VR_MII_EEE_RX_QUIET_EN		BIT(3)  /* Rx Quiet Enable */
+#define DW_VR_MII_EEE_TX_EN_CTRL		BIT(4)  /* Tx Control Enable */
+#define DW_VR_MII_EEE_RX_EN_CTRL		BIT(7)  /* Rx Control Enable */
+
+#define DW_VR_MII_EEE_MULT_FACT_100NS_SHIFT	8
+#define DW_VR_MII_EEE_MULT_FACT_100NS		GENMASK(11, 8)
+
+/* VR MII EEE Control 1 defines */
+#define DW_VR_MII_EEE_TRN_LPI		BIT(0)	/* Transparent Mode Enable */
+
 static const int xpcs_usxgmii_features[] = {
 	ETHTOOL_LINK_MODE_Pause_BIT,
 	ETHTOOL_LINK_MODE_Asym_Pause_BIT,
@@ -650,6 +667,39 @@ static int xpcs_validate(struct mdio_xpcs_args *xpcs,
 	return 0;
 }
 
+static int xpcs_config_eee(struct mdio_xpcs_args *xpcs, int mult_fact_100ns,
+			   int enable)
+{
+	int ret;
+
+	if (enable) {
+	/* Enable EEE */
+		ret = DW_VR_MII_EEE_LTX_EN | DW_VR_MII_EEE_LRX_EN |
+		      DW_VR_MII_EEE_TX_QUIET_EN | DW_VR_MII_EEE_RX_QUIET_EN |
+		      DW_VR_MII_EEE_TX_EN_CTRL | DW_VR_MII_EEE_RX_EN_CTRL |
+		      mult_fact_100ns << DW_VR_MII_EEE_MULT_FACT_100NS_SHIFT;
+	} else {
+		ret = xpcs_read(xpcs, MDIO_MMD_VEND2, DW_VR_MII_EEE_MCTRL0);
+		if (ret < 0)
+			return ret;
+		ret &= ~(DW_VR_MII_EEE_LTX_EN | DW_VR_MII_EEE_LRX_EN |
+		       DW_VR_MII_EEE_TX_QUIET_EN | DW_VR_MII_EEE_RX_QUIET_EN |
+		       DW_VR_MII_EEE_TX_EN_CTRL | DW_VR_MII_EEE_RX_EN_CTRL |
+		       DW_VR_MII_EEE_MULT_FACT_100NS);
+	}
+
+	ret = xpcs_write(xpcs, MDIO_MMD_VEND2, DW_VR_MII_EEE_MCTRL0, ret);
+	if (ret < 0)
+		return ret;
+
+	ret = xpcs_read(xpcs, MDIO_MMD_VEND2, DW_VR_MII_EEE_MCTRL1);
+	if (ret < 0)
+		return ret;
+
+	ret |= DW_VR_MII_EEE_TRN_LPI;
+	return xpcs_write(xpcs, MDIO_MMD_VEND2, DW_VR_MII_EEE_MCTRL1, ret);
+}
+
 static int xpcs_config_aneg_c37_sgmii(struct mdio_xpcs_args *xpcs)
 {
 	int ret;
@@ -908,6 +958,7 @@ static struct mdio_xpcs_ops xpcs_ops = {
 	.get_state = xpcs_get_state,
 	.link_up = xpcs_link_up,
 	.probe = xpcs_probe,
+	.config_eee = xpcs_config_eee,
 };
 
 struct mdio_xpcs_ops *mdio_xpcs_get_ops(void)
diff --git a/include/linux/pcs/pcs-xpcs.h b/include/linux/pcs/pcs-xpcs.h
index 2cb5188a7ef1..5938ced805f4 100644
--- a/include/linux/pcs/pcs-xpcs.h
+++ b/include/linux/pcs/pcs-xpcs.h
@@ -32,6 +32,8 @@ struct mdio_xpcs_ops {
 	int (*link_up)(struct mdio_xpcs_args *xpcs, int speed,
 		       phy_interface_t interface);
 	int (*probe)(struct mdio_xpcs_args *xpcs, phy_interface_t interface);
+	int (*config_eee)(struct mdio_xpcs_args *xpcs, int mult_fact_100ns,
+			  int enable);
 };
 
 #if IS_ENABLED(CONFIG_PCS_XPCS)
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH net-next 2/2] net: stmmac: Add callbacks for DWC xpcs Energy Efficient Ethernet

[Michael Sit Wei Hong]

Link xpcs callback functions for MAC to configure the xpcs EEE feature.

The clk_eee frequency is used to calculate the MULT_FACT_100NS. This is
to adjust the clock tic closer to 100ns.

Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
---
 drivers/net/ethernet/stmicro/stmmac/dwmac-intel.c    | 11 +++++++++++
 drivers/net/ethernet/stmicro/stmmac/hwif.h           |  2 ++
 drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c |  6 ++++++
 include/linux/stmmac.h                               |  1 +
 4 files changed, 20 insertions(+)

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-intel.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-intel.c
index 80728a4c0e3f..e36a8cc59ad0 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-intel.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-intel.c
@@ -429,6 +429,17 @@ static int intel_mgbe_common_data(struct pci_dev *pdev,
 	plat->force_sf_dma_mode = 0;
 	plat->tso_en = 1;
 
+	/* Multiplying factor to the clk_eee_i clock time
+	 * period to make it closer to 100 ns. This value
+	 * should be programmed such that the clk_eee_time_period *
+	 * (MULT_FACT_100NS + 1) should be within 80 ns to 120 ns
+	 * clk_eee frequency is 19.2Mhz
+	 * clk_eee_time_period is 52ns
+	 * 52ns * (1 + 1) = 104ns
+	 * MULT_FACT_100NS = 1
+	 */
+	plat->mult_fact_100ns = 1;
+
 	plat->rx_sched_algorithm = MTL_RX_ALGORITHM_SP;
 
 	for (i = 0; i < plat->rx_queues_to_use; i++) {
diff --git a/drivers/net/ethernet/stmicro/stmmac/hwif.h b/drivers/net/ethernet/stmicro/stmmac/hwif.h
index 2cc91759b91f..c678d7b826a3 100644
--- a/drivers/net/ethernet/stmicro/stmmac/hwif.h
+++ b/drivers/net/ethernet/stmicro/stmmac/hwif.h
@@ -624,6 +624,8 @@ struct stmmac_mmc_ops {
 	stmmac_do_callback(__priv, xpcs, link_up, __args)
 #define stmmac_xpcs_probe(__priv, __args...) \
 	stmmac_do_callback(__priv, xpcs, probe, __args)
+#define stmmac_xpcs_config_eee(__priv, __args...) \
+	stmmac_do_callback(__priv, xpcs, config_eee, __args)
 
 struct stmmac_regs_off {
 	u32 ptp_off;
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c
index 61b11639ee0c..1f6d749fd9a3 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c
@@ -720,6 +720,12 @@ static int stmmac_ethtool_op_set_eee(struct net_device *dev,
 		netdev_warn(priv->dev,
 			    "Setting EEE tx-lpi is not supported\n");
 
+	ret = stmmac_xpcs_config_eee(priv, &priv->hw->xpcs_args,
+				     priv->plat->mult_fact_100ns,
+				     edata->eee_enabled);
+	if (ret)
+		return ret;
+
 	if (!edata->eee_enabled)
 		stmmac_disable_eee_mode(priv);
 
diff --git a/include/linux/stmmac.h b/include/linux/stmmac.h
index 0db36360ef21..e14a12df381b 100644
--- a/include/linux/stmmac.h
+++ b/include/linux/stmmac.h
@@ -223,6 +223,7 @@ struct plat_stmmacenet_data {
 	struct clk *clk_ptp_ref;
 	unsigned int clk_ptp_rate;
 	unsigned int clk_ref_rate;
+	unsigned int mult_fact_100ns;
 	s32 ptp_max_adj;
 	struct reset_control *stmmac_rst;
 	struct stmmac_axi *axi;
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH net-next 2/2] net: stmmac: Add callbacks for DWC xpcs Energy Efficient Ethernet

[Russell King (Oracle)]

On Mon, May 17, 2021 at 05:43:32PM +0800, Michael Sit Wei Hong wrote:
> Link xpcs callback functions for MAC to configure the xpcs EEE feature.
> 
> The clk_eee frequency is used to calculate the MULT_FACT_100NS. This is
> to adjust the clock tic closer to 100ns.
> 
> Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>

What is the initial state of the EEE configuration before the first
call to stmmac_ethtool_op_set_eee()? Does it reflect the default EEE
settings?

-- 
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at last!

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

RE: [PATCH net-next 2/2] net: stmmac: Add callbacks for DWC xpcs Energy Efficient Ethernet

[Sit, Michael Wei Hong]

> -----Original Message-----
> From: Russell King <linux@armlinux.org.uk>
> Sent: Monday, 17 May, 2021 6:54 PM
> To: Sit, Michael Wei Hong <michael.wei.hong.sit@intel.com>
> Cc: Jose.Abreu@synopsys.com; andrew@lunn.ch;
> hkallweit1@gmail.com; kuba@kernel.org;
> netdev@vger.kernel.org; peppe.cavallaro@st.com;
> alexandre.torgue@foss.st.com; davem@davemloft.net;
> mcoquelin.stm32@gmail.com; Voon, Weifeng
> <weifeng.voon@intel.com>; Ong, Boon Leong
> <boon.leong.ong@intel.com>; Tan, Tee Min
> <tee.min.tan@intel.com>; vee.khee.wong@linux.intel.com;
> Wong, Vee Khee <vee.khee.wong@intel.com>; linux-stm32@st-
> md-mailman.stormreply.com; linux-arm-
> kernel@lists.infradead.org; linux-kernel@vger.kernel.org
> Subject: Re: [PATCH net-next 2/2] net: stmmac: Add callbacks for
> DWC xpcs Energy Efficient Ethernet
> 
> On Mon, May 17, 2021 at 05:43:32PM +0800, Michael Sit Wei Hong
> wrote:
> > Link xpcs callback functions for MAC to configure the xpcs EEE
> feature.
> >
> > The clk_eee frequency is used to calculate the
> MULT_FACT_100NS. This
> > is to adjust the clock tic closer to 100ns.
> >
> > Signed-off-by: Michael Sit Wei Hong
> <michael.wei.hong.sit@intel.com>
> 
> What is the initial state of the EEE configuration before the first
> call to stmmac_ethtool_op_set_eee()? Does it reflect the default
> EEE settings?

The register values before the first call are the default reset values in
the registers. The reset values assumes the clk_eee_i time period is 10ns,
Hence, the reset value is set to 9.
According to the register description,
This value should be programmed such that the
clk_eee_i_time_period * (MULT_FACT_100NS + 1) should be
within 80 ns to 120 ns.

Since we are using a fixed 19.2MHz clk_eee, which is 52ns,
we are setting the value to 1.
> 
> --
> RMK's Patch system:
> https://www.armlinux.org.uk/developer/patches/
> FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at
> last!

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH net-next 2/2] net: stmmac: Add callbacks for DWC xpcs Energy Efficient Ethernet

[Russell King (Oracle)]

On Mon, May 17, 2021 at 11:37:12AM +0000, Sit, Michael Wei Hong wrote:
> > From: Russell King <linux@armlinux.org.uk>
> > 
> > On Mon, May 17, 2021 at 05:43:32PM +0800, Michael Sit Wei Hong
> > wrote:
> > > Link xpcs callback functions for MAC to configure the xpcs EEE
> > feature.
> > >
> > > The clk_eee frequency is used to calculate the
> > MULT_FACT_100NS. This
> > > is to adjust the clock tic closer to 100ns.
> > >
> > > Signed-off-by: Michael Sit Wei Hong
> > <michael.wei.hong.sit@intel.com>
> > 
> > What is the initial state of the EEE configuration before the first
> > call to stmmac_ethtool_op_set_eee()? Does it reflect the default
> > EEE settings?
> 
> The register values before the first call are the default reset values in
> the registers. The reset values assumes the clk_eee_i time period is 10ns,
> Hence, the reset value is set to 9.
> According to the register description,
> This value should be programmed such that the
> clk_eee_i_time_period * (MULT_FACT_100NS + 1) should be
> within 80 ns to 120 ns.
> 
> Since we are using a fixed 19.2MHz clk_eee, which is 52ns,
> we are setting the value to 1.

Does that hardware default configuration match what is returned by
ethtool --show-eee ?
 
-- 
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at last!

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

RE: [PATCH net-next 2/2] net: stmmac: Add callbacks for DWC xpcs Energy Efficient Ethernet

[Sit, Michael Wei Hong]

> -----Original Message-----
> From: Russell King <linux@armlinux.org.uk>
> Sent: Tuesday, 18 May, 2021 6:06 PM
> To: Sit, Michael Wei Hong <michael.wei.hong.sit@intel.com>
> Cc: Jose.Abreu@synopsys.com; andrew@lunn.ch;
> hkallweit1@gmail.com; kuba@kernel.org;
> netdev@vger.kernel.org; peppe.cavallaro@st.com;
> alexandre.torgue@foss.st.com; davem@davemloft.net;
> mcoquelin.stm32@gmail.com; Voon, Weifeng
> <weifeng.voon@intel.com>; Ong, Boon Leong
> <boon.leong.ong@intel.com>; Tan, Tee Min
> <tee.min.tan@intel.com>; vee.khee.wong@linux.intel.com;
> Wong, Vee Khee <vee.khee.wong@intel.com>; linux-stm32@st-
> md-mailman.stormreply.com; linux-arm-
> kernel@lists.infradead.org; linux-kernel@vger.kernel.org
> Subject: Re: [PATCH net-next 2/2] net: stmmac: Add callbacks for
> DWC xpcs Energy Efficient Ethernet
> 
> On Mon, May 17, 2021 at 11:37:12AM +0000, Sit, Michael Wei
> Hong wrote:
> > > From: Russell King <linux@armlinux.org.uk>
> > >
> > > On Mon, May 17, 2021 at 05:43:32PM +0800, Michael Sit Wei
> Hong
> > > wrote:
> > > > Link xpcs callback functions for MAC to configure the xpcs
> EEE
> > > feature.
> > > >
> > > > The clk_eee frequency is used to calculate the
> > > MULT_FACT_100NS. This
> > > > is to adjust the clock tic closer to 100ns.
> > > >
> > > > Signed-off-by: Michael Sit Wei Hong
> > > <michael.wei.hong.sit@intel.com>
> > >
> > > What is the initial state of the EEE configuration before the
> first
> > > call to stmmac_ethtool_op_set_eee()? Does it reflect the
> default EEE
> > > settings?
> >
> > The register values before the first call are the default reset
> values
> > in the registers. The reset values assumes the clk_eee_i time
> period
> > is 10ns, Hence, the reset value is set to 9.
> > According to the register description, This value should be
> programmed
> > such that the clk_eee_i_time_period * (MULT_FACT_100NS + 1)
> should be
> > within 80 ns to 120 ns.
> >
> > Since we are using a fixed 19.2MHz clk_eee, which is 52ns, we
> are
> > setting the value to 1.
> 
> Does that hardware default configuration match what is returned
> by ethtool --show-eee ?

May I know what is the hardware default configuration that is expected
to be returned by ethtool --show-eee?
The MULT_FACT_100NS value is an internal register setting not meant
to be exposed to userspace, and only relevant when EEE is enabled.
> 
> --
> RMK's Patch system:
> https://www.armlinux.org.uk/developer/patches/
> FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at
> last!

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH net-next 0/2] Introducing support for DWC xpcs Energy Efficient Ethernet

[patchwork-bot+netdevbpf]

Hello:

This series was applied to netdev/net-next.git (refs/heads/master):

On Mon, 17 May 2021 17:43:30 +0800 you wrote:
> The goal of this patch set is to enable EEE in the xpcs so that when
> EEE is enabled, the MAC-->xpcs-->PHY have all the EEE related
> configurations enabled.
> 
> Patch 1 adds the functions to enable EEE in the xpcs and sets it to
> transparent mode.
> Patch 2 adds the callbacks to configure the xpcs EEE mode.
> 
> [...]

Here is the summary with links:
  - [net-next,1/2] net: pcs: Introducing support for DWC xpcs Energy Efficient Ethernet
    https://git.kernel.org/netdev/net-next/c/7617af3d1a5e
  - [net-next,2/2] net: stmmac: Add callbacks for DWC xpcs Energy Efficient Ethernet
    https://git.kernel.org/netdev/net-next/c/e80fe71b3ffe

You are awesome, thank you!
--
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html



_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH net-next 0/2] Introducing support for DWC xpcs Energy Efficient Ethernet

[Michael Sit Wei Hong]

The goal of this patch set is to enable EEE in the xpcs so that when
EEE is enabled, the MAC-->xpcs-->PHY have all the EEE related
configurations enabled.

Patch 1 adds the functions to enable EEE in the xpcs and sets it to
transparent mode.
Patch 2 adds the callbacks to configure the xpcs EEE mode.

The results are tested by checking the lpi counters of the tx and rx
path of the interface. When EEE is enabled, the lpi counters should
increament as it enters and exits lpi states.

host@EHL$ ethtool --show-eee enp0s30f4
EEE Settings for enp0s30f4:
        EEE status: disabled
        Tx LPI: disabled
        Supported EEE link modes:  100baseT/Full
                                   1000baseT/Full
        Advertised EEE link modes:  Not reported
        Link partner advertised EEE link modes:  100baseT/Full
                                                 1000baseT/Full
host@EHL$ ethtool -S enp0s30f4 | grep lpi
     irq_tx_path_in_lpi_mode_n: 0
     irq_tx_path_exit_lpi_mode_n: 0
     irq_rx_path_in_lpi_mode_n: 0
     irq_rx_path_exit_lpi_mode_n: 0
host@EHL$ ethtool --set-eee enp0s30f4 eee on
host@EHL$ [  110.265154] intel-eth-pci 0000:00:1e.4 enp0s30f4: Link is Down
[  112.315155] intel-eth-pci 0000:00:1e.4 enp0s30f4: Link is Up - 1Gbps/Full - flow control off
[  112.324612] IPv6: ADDRCONF(NETDEV_CHANGE): enp0s30f4: link becomes ready
host@EHL$ ethtool --show-eee enp0s30f4
EEE Settings for enp0s30f4:
        EEE status: enabled - active
        Tx LPI: 1000000 (us)
        Supported EEE link modes:  100baseT/Full
                                   1000baseT/Full
        Advertised EEE link modes:  100baseT/Full
                                    1000baseT/Full
        Link partner advertised EEE link modes:  100baseT/Full
                                                 1000baseT/Full
host@EHL$ ethtool -S enp0s30f4 | grep lpi
     irq_tx_path_in_lpi_mode_n: 6
     irq_tx_path_exit_lpi_mode_n: 5
     irq_rx_path_in_lpi_mode_n: 7
     irq_rx_path_exit_lpi_mode_n: 6
host@EHL$ ping 192.168.1.1
PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=1.02 ms
64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=0.510 ms
64 bytes from 192.168.1.1: icmp_seq=3 ttl=64 time=0.489 ms
64 bytes from 192.168.1.1: icmp_seq=4 ttl=64 time=0.484 ms
64 bytes from 192.168.1.1: icmp_seq=5 ttl=64 time=0.504 ms
64 bytes from 192.168.1.1: icmp_seq=6 ttl=64 time=0.466 ms
64 bytes from 192.168.1.1: icmp_seq=7 ttl=64 time=0.529 ms
64 bytes from 192.168.1.1: icmp_seq=8 ttl=64 time=0.519 ms
64 bytes from 192.168.1.1: icmp_seq=9 ttl=64 time=0.518 ms
64 bytes from 192.168.1.1: icmp_seq=10 ttl=64 time=0.501 ms

--- 192.168.1.1 ping statistics ---
10 packets transmitted, 10 received, 0% packet loss, time 9216ms
rtt min/avg/max/mdev = 0.466/0.553/1.018/0.155 ms
host@EHL$ ethtool -S enp0s30f4 | grep lpi
     irq_tx_path_in_lpi_mode_n: 22
     irq_tx_path_exit_lpi_mode_n: 21
     irq_rx_path_in_lpi_mode_n: 21
     irq_rx_path_exit_lpi_mode_n: 20

Michael Sit Wei Hong (2):
  net: pcs: Introducing support for DWC xpcs Energy Efficient Ethernet
  net: stmmac: Add callbacks for DWC xpcs Energy Efficient Ethernet

 .../net/ethernet/stmicro/stmmac/dwmac-intel.c | 11 ++++
 drivers/net/ethernet/stmicro/stmmac/hwif.h    |  2 +
 .../ethernet/stmicro/stmmac/stmmac_ethtool.c  |  6 +++
 drivers/net/pcs/pcs-xpcs.c                    | 51 +++++++++++++++++++
 include/linux/pcs/pcs-xpcs.h                  |  2 +
 include/linux/stmmac.h                        |  1 +
 6 files changed, 73 insertions(+)

-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH net-next 2/2] net: stmmac: Add callbacks for DWC xpcs Energy Efficient Ethernet

[Michael Sit Wei Hong]

Link xpcs callback functions for MAC to configure the xpcs EEE feature.

The clk_eee frequency is used to calculate the MULT_FACT_100NS. This is
to adjust the clock tic closer to 100ns.

Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
---
 drivers/net/ethernet/stmicro/stmmac/dwmac-intel.c    | 11 +++++++++++
 drivers/net/ethernet/stmicro/stmmac/hwif.h           |  2 ++
 drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c |  6 ++++++
 include/linux/stmmac.h                               |  1 +
 4 files changed, 20 insertions(+)

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-intel.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-intel.c
index 80728a4c0e3f..e36a8cc59ad0 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-intel.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-intel.c
@@ -429,6 +429,17 @@ static int intel_mgbe_common_data(struct pci_dev *pdev,
 	plat->force_sf_dma_mode = 0;
 	plat->tso_en = 1;
 
+	/* Multiplying factor to the clk_eee_i clock time
+	 * period to make it closer to 100 ns. This value
+	 * should be programmed such that the clk_eee_time_period *
+	 * (MULT_FACT_100NS + 1) should be within 80 ns to 120 ns
+	 * clk_eee frequency is 19.2Mhz
+	 * clk_eee_time_period is 52ns
+	 * 52ns * (1 + 1) = 104ns
+	 * MULT_FACT_100NS = 1
+	 */
+	plat->mult_fact_100ns = 1;
+
 	plat->rx_sched_algorithm = MTL_RX_ALGORITHM_SP;
 
 	for (i = 0; i < plat->rx_queues_to_use; i++) {
diff --git a/drivers/net/ethernet/stmicro/stmmac/hwif.h b/drivers/net/ethernet/stmicro/stmmac/hwif.h
index 2cc91759b91f..c678d7b826a3 100644
--- a/drivers/net/ethernet/stmicro/stmmac/hwif.h
+++ b/drivers/net/ethernet/stmicro/stmmac/hwif.h
@@ -624,6 +624,8 @@ struct stmmac_mmc_ops {
 	stmmac_do_callback(__priv, xpcs, link_up, __args)
 #define stmmac_xpcs_probe(__priv, __args...) \
 	stmmac_do_callback(__priv, xpcs, probe, __args)
+#define stmmac_xpcs_config_eee(__priv, __args...) \
+	stmmac_do_callback(__priv, xpcs, config_eee, __args)
 
 struct stmmac_regs_off {
 	u32 ptp_off;
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c
index 61b11639ee0c..1f6d749fd9a3 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c
@@ -720,6 +720,12 @@ static int stmmac_ethtool_op_set_eee(struct net_device *dev,
 		netdev_warn(priv->dev,
 			    "Setting EEE tx-lpi is not supported\n");
 
+	ret = stmmac_xpcs_config_eee(priv, &priv->hw->xpcs_args,
+				     priv->plat->mult_fact_100ns,
+				     edata->eee_enabled);
+	if (ret)
+		return ret;
+
 	if (!edata->eee_enabled)
 		stmmac_disable_eee_mode(priv);
 
diff --git a/include/linux/stmmac.h b/include/linux/stmmac.h
index 0db36360ef21..e14a12df381b 100644
--- a/include/linux/stmmac.h
+++ b/include/linux/stmmac.h
@@ -223,6 +223,7 @@ struct plat_stmmacenet_data {
 	struct clk *clk_ptp_ref;
 	unsigned int clk_ptp_rate;
 	unsigned int clk_ref_rate;
+	unsigned int mult_fact_100ns;
 	s32 ptp_max_adj;
 	struct reset_control *stmmac_rst;
 	struct stmmac_axi *axi;
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel