linux-arm-kernel.lists.infradead.org archive mirror
 help / color / mirror / Atom feed
From: Jerry Huang <jerry.huang@nxp.com>
To: "linux-arm-kernel@lists.infradead.org"
	<linux-arm-kernel@lists.infradead.org>,
	"linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>,
	"devicetree@vger.kernel.org" <devicetree@vger.kernel.org>,
	"robh+dt@kernel.org" <robh+dt@kernel.org>,
	"arnd@arndb.de" <arnd@arndb.de>,
	"olof@lixom.net" <olof@lixom.net>,
	"soc@kernel.org" <soc@kernel.org>,
	"shawnguo@kernel.org" <shawnguo@kernel.org>,
	Leo Li <leoyang.li@nxp.com>,
	"krzysztof.kozlowski@canonical.com"
	<krzysztof.kozlowski@canonical.com>,
	"linux@rempel-privat.de" <linux@rempel-privat.de>,
	"festevam@gmail.com" <festevam@gmail.com>,
	"tharvey@gateworks.com" <tharvey@gateworks.com>,
	Marcel Ziswiler <marcel.ziswiler@toradex.com>,
	"jagan@amarulasolutions.com" <jagan@amarulasolutions.com>,
	"dev@lynxeye.de" <dev@lynxeye.de>,
	"cniedermaier@dh-electronics.com"
	<cniedermaier@dh-electronics.com>,
	"sebastian.reichel@collabora.com"
	<sebastian.reichel@collabora.com>
Cc: Alison Wang <alison.wang@nxp.com>
Subject: RE: [PATCH 2/2] ARM: dts: Add initial LS1021A IoT board dts support
Date: Tue, 8 Feb 2022 01:49:59 +0000	[thread overview]
Message-ID: <VE1PR04MB6477BB08C1AF9F1E5A0B0C1BFE2D9@VE1PR04MB6477.eurprd04.prod.outlook.com> (raw)
In-Reply-To: <20211203031332.902485-2-jerry.huang@nxp.com>

Any comment for this patch?


Best Regards
Jerry Huang

-----Original Message-----
From: Jerry Huang <jerry.huang@nxp.com> 
Sent: 2021年12月3日 11:14
To: linux-arm-kernel@lists.infradead.org; linux-kernel@vger.kernel.org; devicetree@vger.kernel.org; robh+dt@kernel.org; arnd@arndb.de; olof@lixom.net; soc@kernel.org; shawnguo@kernel.org; Leo Li <leoyang.li@nxp.com>; krzysztof.kozlowski@canonical.com; linux@rempel-privat.de; festevam@gmail.com; tharvey@gateworks.com; Marcel Ziswiler <marcel.ziswiler@toradex.com>; jagan@amarulasolutions.com; dev@lynxeye.de; cniedermaier@dh-electronics.com; sebastian.reichel@collabora.com
Cc: Jerry Huang <jerry.huang@nxp.com>; Alison Wang <alison.wang@nxp.com>
Subject: [PATCH 2/2] ARM: dts: Add initial LS1021A IoT board dts support

The LS1021A-IoT gateway reference design is a purpose-built, small footprint hardware platform equipped with a wide array of both high-speed connectivity and low speed serial interfaces.

CC: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Changming Huang <jerry.huang@nxp.com>
Signed-off-by: Alison Wang <alison.wang@nxp.com>
---
 arch/arm/boot/dts/Makefile        |   3 +-
 arch/arm/boot/dts/ls1021a-iot.dts | 248 ++++++++++++++++++++++++++++++
 2 files changed, 250 insertions(+), 1 deletion(-)  create mode 100644 arch/arm/boot/dts/ls1021a-iot.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 0de64f237cd8..8534f6f94bc3 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -727,7 +727,8 @@ dtb-$(CONFIG_SOC_LS1021A) += \
 	ls1021a-moxa-uc-8410a.dtb \
 	ls1021a-qds.dtb \
 	ls1021a-tsn.dtb \
-	ls1021a-twr.dtb
+	ls1021a-twr.dtb \
+	ls1021a-iot.dtb
 dtb-$(CONFIG_SOC_VF610) += \
 	vf500-colibri-eval-v3.dtb \
 	vf610-bk4.dtb \
diff --git a/arch/arm/boot/dts/ls1021a-iot.dts b/arch/arm/boot/dts/ls1021a-iot.dts
new file mode 100644
index 000000000000..47ad718dc542
--- /dev/null
+++ b/arch/arm/boot/dts/ls1021a-iot.dts
@@ -0,0 +1,248 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2021 NXP
+ *
+ */
+
+/dts-v1/;
+#include "ls1021a.dtsi"
+
+/ {
+	model = "LS1021A-IOT Board";
+	compatible = "fsl,ls1021a-iot", "fsl,ls1021a";
+
+	sys_mclk: clock-mclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24576000>;
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reg_3p3v: regulator@0 {
+			compatible = "regulator-fixed";
+			reg = <0>;
+			regulator-name = "3P3V";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		reg_2p5v: regulator@1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "2P5V";
+			regulator-min-microvolt = <2500000>;
+			regulator-max-microvolt = <2500000>;
+			regulator-always-on;
+		};
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,widgets =
+			"Microphone", "Microphone Jack",
+			"Headphone", "Headphone Jack",
+			"Speaker", "Speaker Ext",
+			"Line", "Line In Jack";
+		simple-audio-card,routing =
+			"MIC_IN", "Microphone Jack",
+			"Microphone Jack", "Mic Bias",
+			"LINE_IN", "Line In Jack",
+			"Headphone Jack", "HP_OUT",
+			"Speaker Ext", "LINE_OUT";
+
+		simple-audio-card,cpu {
+			sound-dai = <&sai2>;
+			frame-master;
+			bitclock-master;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&codec>;
+			frame-master;
+			bitclock-master;
+		};
+	};
+};
+
+&enet0 {
+	tbi-handle = <&tbi1>;
+	phy-handle = <&phy1>;
+	phy-connection-type = "sgmii";
+	status = "okay";
+};
+
+&enet1 {
+	tbi-handle = <&tbi1>;
+	phy-handle = <&phy3>;
+	phy-connection-type = "sgmii";
+	status = "okay";
+};
+
+&enet2 {
+	fixed-link = <0 1 1000 0 0>;
+	phy-connection-type = "rgmii-id";
+	status = "okay";
+};
+
+&can0{
+	status = "disabled";
+};
+
+&can1{
+	status = "disabled";
+};
+
+&can2{
+	status = "disabled";
+};
+
+&can3{
+	status = "okay";
+};
+
+&esdhc{
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	max1239@35 {
+		compatible = "maxim,max1239";
+		reg = <0x35>;
+		#io-channel-cells = <1>;
+	};
+
+	codec: sgtl5000@2a {
+		#sound-dai-cells=<0x0>;
+		compatible = "fsl,sgtl5000";
+		reg = <0x2a>;
+		VDDA-supply = <&reg_3p3v>;
+		VDDIO-supply = <&reg_2p5v>;
+		clocks = <&sys_mclk 1>;
+	};
+
+	pca9555: pca9555@23 {
+		compatible = "nxp,pca9555";
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		reg = <0x23>;
+	};
+
+	ina220@44 {
+		compatible = "ti,ina220";
+		reg = <0x44>;
+		shunt-resistor = <1000>;
+	};
+
+	ina220@45 {
+		compatible = "ti,ina220";
+		reg = <0x45>;
+		shunt-resistor = <1000>;
+	};
+
+	lm75b@48 {
+		compatible = "national,lm75b";
+		reg = <0x48>;
+	};
+
+	adt7461a@4c {
+		compatible = "adt7461a";
+		reg = <0x4c>;
+	};
+};
+
+&i2c1 {
+	status = "disabled";
+};
+
+&ifc {
+	status = "disabled";
+};
+
+&lpuart0 {
+	status = "okay";
+};
+
+&mdio0 {
+	phy0: ethernet-phy@0 {
+		reg = <0x0>;
+	};
+
+	phy1: ethernet-phy@1 {
+		reg = <0x1>;
+	};
+
+	phy2: ethernet-phy@2 {
+		reg = <0x2>;
+	};
+
+	phy3: ethernet-phy@3 {
+		reg = <0x3>;
+	};
+
+	tbi1: tbi-phy@1f {
+		reg = <0x1f>;
+		device_type = "tbi-phy";
+	};
+};
+
+&qspi {
+	num-cs = <2>;
+	status = "okay";
+
+	qflash0: s25fl128s@0 {
+		compatible = "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		spi-max-frequency = <20000000>;
+		reg = <0>;
+	};
+};
+
+&sai2 {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&dcu {
+	display = <&display>;
+	status = "okay";
+
+	display: display@0 {
+		bits-per-pixel = <24>;
+
+		display-timings {
+			native-mode = <&timing0>;
+
+			timing0: mode0 {
+				clock-frequency = <25000000>;
+				hactive = <640>;
+				vactive = <480>;
+				hback-porch = <80>;
+				hfront-porch = <80>;
+				vback-porch = <16>;
+				vfront-porch = <16>;
+				hsync-len = <12>;
+				vsync-len = <2>;
+				hsync-active = <1>;
+				vsync-active = <1>;
+			};
+		};
+	};
+};
--
2.25.1

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

  parent reply	other threads:[~2022-02-08  1:51 UTC|newest]

Thread overview: 6+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-12-03  3:13 [PATCH 1/2] dt-bindings: arm: fsl: add ls1021a-iot board Changming Huang
2021-12-03  3:13 ` [PATCH 2/2] ARM: dts: Add initial LS1021A IoT board dts support Changming Huang
2021-12-14  4:02   ` Shawn Guo
2022-02-08  1:49   ` Jerry Huang [this message]
2022-02-08  7:41     ` Arnd Bergmann
2021-12-13 20:29 ` [PATCH 1/2] dt-bindings: arm: fsl: add ls1021a-iot board Rob Herring

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=VE1PR04MB6477BB08C1AF9F1E5A0B0C1BFE2D9@VE1PR04MB6477.eurprd04.prod.outlook.com \
    --to=jerry.huang@nxp.com \
    --cc=alison.wang@nxp.com \
    --cc=arnd@arndb.de \
    --cc=cniedermaier@dh-electronics.com \
    --cc=dev@lynxeye.de \
    --cc=devicetree@vger.kernel.org \
    --cc=festevam@gmail.com \
    --cc=jagan@amarulasolutions.com \
    --cc=krzysztof.kozlowski@canonical.com \
    --cc=leoyang.li@nxp.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux@rempel-privat.de \
    --cc=marcel.ziswiler@toradex.com \
    --cc=olof@lixom.net \
    --cc=robh+dt@kernel.org \
    --cc=sebastian.reichel@collabora.com \
    --cc=shawnguo@kernel.org \
    --cc=soc@kernel.org \
    --cc=tharvey@gateworks.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).