From: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To: Michal Simek <michal.simek@xilinx.com>
Cc: monstr@monstr.eu, linux-usb@vger.kernel.org,
Bastien Nocera <hadess@hadess.net>,
Piyush Mehta <piyush.mehta@xilinx.com>,
Masahiro Yamada <masahiroy@kernel.org>,
Al Cooper <alcooperx@gmail.com>,
linux-kernel@vger.kernel.org,
Alan Stern <stern@rowland.harvard.edu>,
git@xilinx.com, "Alexander A. Klimov" <grandmaster@al2klimov.de>,
linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH 2/2] usb: misc: usb5744: Add support for USB hub controller
Date: Tue, 9 Feb 2021 11:03:17 +0100 [thread overview]
Message-ID: <YCJd5Xoy1cT6bCIB@kroah.com> (raw)
In-Reply-To: <e1e1d47982018ccd5a763f199680babc0df848c8.1612864393.git.michal.simek@xilinx.com>
On Tue, Feb 09, 2021 at 10:53:20AM +0100, Michal Simek wrote:
> From: Piyush Mehta <piyush.mehta@xilinx.com>
>
> This patch adds a USB GPIO based hub reset for USB5744 hub. This usb5744
> driver trigger hub reset signal after soft reset or core Reset. The HUB
> needs to be resetted after completion of phy initialization. After the
> toggling of gpio, hub configure using i2c usb attached command.
>
> USB5744 hub can be used without any I2C connection, is handled by a
> simple platform device driver.
>
> As part of the reset, sets the direction of the pin to output before
> toggling the pin. Delay of millisecond is added in between low and
> high to meet the setup and hold time requirement of the reset.
>
> Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
> ---
>
> MAINTAINERS | 1 +
> drivers/usb/misc/Kconfig | 9 +++
> drivers/usb/misc/Makefile | 1 +
> drivers/usb/misc/usb5744.c | 115 +++++++++++++++++++++++++++++++++++++
> 4 files changed, 126 insertions(+)
> create mode 100644 drivers/usb/misc/usb5744.c
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 7439471b5d37..56d1fcdd24f6 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -2706,6 +2706,7 @@ F: drivers/edac/synopsys_edac.c
> F: drivers/i2c/busses/i2c-cadence.c
> F: drivers/i2c/busses/i2c-xiic.c
> F: drivers/mmc/host/sdhci-of-arasan.c
> +F: drivers/usb/misc/usb5744.c
> N: zynq
> N: xilinx
>
> diff --git a/drivers/usb/misc/Kconfig b/drivers/usb/misc/Kconfig
> index 8f1144359012..30335b5c4f88 100644
> --- a/drivers/usb/misc/Kconfig
> +++ b/drivers/usb/misc/Kconfig
> @@ -242,6 +242,15 @@ config USB_HUB_USB251XB
> parameters may be set in devicetree or platform data.
> Say Y or M here if you need to configure such a device via SMBus.
>
> +config USB_USB5744
> + tristate "Microchip USB5744 Hub driver"
> + depends on I2C
> + depends on GPIOLIB
> + help
> + This option enables support for Microchip USB5744 Hub. This driver
> + optionally reset the hub using gpio pin and configure hub via i2c if
> + connected.
> +
> config USB_HSIC_USB3503
> tristate "USB3503 HSIC to USB20 Driver"
> depends on I2C
> diff --git a/drivers/usb/misc/Makefile b/drivers/usb/misc/Makefile
> index 5f4e598573ab..5920146a506a 100644
> --- a/drivers/usb/misc/Makefile
> +++ b/drivers/usb/misc/Makefile
> @@ -25,6 +25,7 @@ obj-$(CONFIG_USB_USS720) += uss720.o
> obj-$(CONFIG_USB_SEVSEG) += usbsevseg.o
> obj-$(CONFIG_USB_YUREX) += yurex.o
> obj-$(CONFIG_USB_HUB_USB251XB) += usb251xb.o
> +obj-$(CONFIG_USB_USB5744) += usb5744.o
Can you follow the convention of the config options we have already, and
make this USB_HUB_USB5744 please?
> obj-$(CONFIG_USB_HSIC_USB3503) += usb3503.o
> obj-$(CONFIG_USB_HSIC_USB4604) += usb4604.o
And then put it in sorted order :)
thanks,
greg k-h
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2021-02-09 10:04 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-02-09 9:53 [PATCH 0/2] usb: misc: Add support for Microchip USB5744 Michal Simek
2021-02-09 9:53 ` [PATCH 1/2] dt-bindings: usb: misc: Add binding for Microchip usb5744 hub Michal Simek
2021-02-09 9:53 ` [PATCH 2/2] usb: misc: usb5744: Add support for USB hub controller Michal Simek
2021-02-09 10:03 ` Greg Kroah-Hartman [this message]
2021-02-09 10:11 ` Michal Simek
2021-02-09 10:40 ` Greg Kroah-Hartman
2021-02-10 2:52 ` Andrew Lunn
2021-02-10 11:03 ` Michal Simek
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=YCJd5Xoy1cT6bCIB@kroah.com \
--to=gregkh@linuxfoundation.org \
--cc=alcooperx@gmail.com \
--cc=git@xilinx.com \
--cc=grandmaster@al2klimov.de \
--cc=hadess@hadess.net \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
--cc=masahiroy@kernel.org \
--cc=michal.simek@xilinx.com \
--cc=monstr@monstr.eu \
--cc=piyush.mehta@xilinx.com \
--cc=stern@rowland.harvard.edu \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).