From: Michal Simek <michal.simek@xilinx.com>
To: Rob Herring <robh@kernel.org>, Piyush Mehta <piyush.mehta@xilinx.com>
Cc: <arnd@arndb.de>, <zou_wei@huawei.com>,
<gregkh@linuxfoundation.org>, <linus.walleij@linaro.org>,
<michal.simek@xilinx.com>, <wendy.liang@xilinx.com>,
<iwamatsu@nigauri.org>, <bgolaszewski@baylibre.com>,
<rajan.vaja@xilinx.com>, <linux-gpio@vger.kernel.org>,
<devicetree@vger.kernel.org>, <git@xilinx.com>,
<sgoud@xilinx.com>, <linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>
Subject: Re: [PATCH V2 2/3] dt-bindings: gpio: zynqmp: Add binding documentation for modepin
Date: Mon, 16 Aug 2021 08:27:45 +0200 [thread overview]
Message-ID: <d71ad7f9-6972-8cc0-6dfb-b5306c9900d0@xilinx.com> (raw)
In-Reply-To: <YRbBnRS0VosXcZWz@robh.at.kernel.org>
On 8/13/21 9:01 PM, Rob Herring wrote:
> On Thu, Aug 05, 2021 at 11:12:18PM +0530, Piyush Mehta wrote:
>> This patch adds DT binding document for zynqmp modepin GPIO controller.
>> Modepin GPIO controller has four GPIO pins which can be configurable
>> as input or output.
>>
>> Modepin driver is a bridge between the peripheral driver and GPIO pins.
>> It has set and get APIs for accessing GPIO pins, based on the device-tree
>> entry of reset-gpio property in the peripheral driver, every pin can be
>> configured as input/output and trigger GPIO pin.
>>
>> For more information please refer zynqMp TRM link:
>> Link: https://www.xilinx.com/support/documentation/user_guides/ug1085-zynq-ultrascale-trm.pdf
>> Chapter 2: Signals, Interfaces, and Pins
>> Table 2-2: Clock, Reset, and Configuration Pins - PS_MODE
>>
>> Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
>> ---
>> Changes in v2:
>> - Addressed review comments: Update commit message
>>
>> https://lore.kernel.org/linux-arm-kernel/20210615080553.2021061-2-piyush.mehta@xilinx.com/T/#mbd1fbda813e33b19397b350bde75747c92a0d7e1
>> https://lore.kernel.org/linux-arm-kernel/20210615080553.2021061-2-piyush.mehta@xilinx.com/T/#me82b1444ab3776162cdb0077dfc9256365c7e736
>> ---
>> .../bindings/gpio/xlnx,zynqmp-gpio-modepin.yaml | 41 ++++++++++++++++++++++
>> 1 file changed, 41 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/gpio/xlnx,zynqmp-gpio-modepin.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/gpio/xlnx,zynqmp-gpio-modepin.yaml b/Documentation/devicetree/bindings/gpio/xlnx,zynqmp-gpio-modepin.yaml
>> new file mode 100644
>> index 0000000..39d78f8
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/gpio/xlnx,zynqmp-gpio-modepin.yaml
>> @@ -0,0 +1,41 @@
>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: "http://devicetree.org/schemas/gpio/xlnx,zynqmp-gpio-modepin.yaml#"
>> +$schema: "http://devicetree.org/meta-schemas/core.yaml#"
>> +
>> +title: ZynqMP Mode Pin GPIO controller
>> +
>> +description:
>> + PS_MODE is 4-bits boot mode pins sampled on POR deassertion. Mode Pin
>> + GPIO controller with configurable from numbers of pins (from 0 to 3 per
>> + PS_MODE). Every pin can be configured as input/output.
>> +
>> +maintainers:
>> + - Piyush Mehta <piyush.mehta@xilinx.com>
>> +
>> +properties:
>> + compatible:
>> + const: xlnx,zynqmp-gpio-modepin
>> +
>> + gpio-controller: true
>> +
>> + "#gpio-cells":
>> + const: 2
>> +
>> +required:
>> + - compatible
>> + - gpio-controller
>> + - "#gpio-cells"
>> +
>> +additionalProperties: false
>> +
>> +examples:
>> + - |
>> + modepin_gpio: gpio {
>> + compatible = "xlnx,zynqmp-gpio-modepin";
>> + gpio-controller;
>> + #gpio-cells = <2>;
>
> No way to interact with this h/w?
>
> As it is part of the firmware interface, it must be a child node in the
> firmware node schema.
Actually it is there. Only example is not showing this properly.
https://github.com/Xilinx/u-boot-xlnx/blob/master/arch/arm/dts/zynqmp.dtsi#L250
Piyush: Can you please do it as we have done with pinctrl.
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/pinctrl/xlnx,zynqmp-pinctrl.yaml?h=v5.14-rc6#n301
like this
zynqmp_firmware: zynqmp-firmware {
modepin_gpio: gpio {
compatible = "xlnx,zynqmp-gpio-modepin";
gpio-controller;
#gpio-cells = <2>;
};
};
That dt labels can be also removed because they are not needed in example.
Thanks,
Michal
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2021-08-16 6:30 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-08-05 17:42 [PATCH V2 0/3] gpio: modepin: Add driver support for modepin GPIO controller Piyush Mehta
2021-08-05 17:42 ` [PATCH V2 1/3] firmware: zynqmp: Add MMIO read and write support for PS_MODE pin Piyush Mehta
2021-08-06 5:49 ` Michal Simek
2021-08-11 13:08 ` Linus Walleij
2021-08-11 13:46 ` Arnd Bergmann
2021-08-11 14:04 ` Michal Simek
2021-08-11 15:14 ` Linus Walleij
2021-08-05 17:42 ` [PATCH V2 2/3] dt-bindings: gpio: zynqmp: Add binding documentation for modepin Piyush Mehta
2021-08-13 19:01 ` Rob Herring
2021-08-16 6:27 ` Michal Simek [this message]
2021-08-05 17:42 ` [PATCH V2 3/3] gpio: modepin: Add driver support for modepin GPIO controller Piyush Mehta
2021-08-11 12:59 ` Linus Walleij
2021-08-11 13:29 ` Michal Simek
2021-08-11 14:45 ` Linus Walleij
2021-08-11 15:12 ` Linus Walleij
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=d71ad7f9-6972-8cc0-6dfb-b5306c9900d0@xilinx.com \
--to=michal.simek@xilinx.com \
--cc=arnd@arndb.de \
--cc=bgolaszewski@baylibre.com \
--cc=devicetree@vger.kernel.org \
--cc=git@xilinx.com \
--cc=gregkh@linuxfoundation.org \
--cc=iwamatsu@nigauri.org \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=piyush.mehta@xilinx.com \
--cc=rajan.vaja@xilinx.com \
--cc=robh@kernel.org \
--cc=sgoud@xilinx.com \
--cc=wendy.liang@xilinx.com \
--cc=zou_wei@huawei.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).