Linux-ARM-Kernel Archive on lore.kernel.org
 help / color / Atom feed
From: Matthias Brugger <mbrugger@suse.com>
To: LABBE Corentin <clabbe@baylibre.com>,
	Matthias Brugger <matthias.bgg@gmail.com>
Cc: linux-kernel@vger.kernel.org, u-boot@lists.denx.de,
	bcm-kernel-feedback-list@broadcom.com,
	linux-rpi-kernel@lists.infradead.org,
	James Morse <james.morse@arm.com>,
	linux-arm-kernel@lists.infradead.org
Subject: Re: RPI4: fail too boot with an initrd
Date: Tue, 18 Feb 2020 11:36:41 +0100
Message-ID: <d9727fac-e7fd-7dfb-ce39-da0c5b0d12a2@suse.com> (raw)
In-Reply-To: <20200218100128.GB10369@Red>



On 18/02/2020 11:01, LABBE Corentin wrote:
> On Mon, Feb 17, 2020 at 02:07:09PM +0100, Matthias Brugger wrote:
>>
>>
>> On 17/02/2020 13:53, LABBE Corentin wrote:
>>> On Mon, Feb 17, 2020 at 11:50:04AM +0100, Matthias Brugger wrote:
>>>>
>>>>
>>>> On 17/02/2020 11:37, LABBE Corentin wrote:
>>>>> On Fri, Feb 14, 2020 at 06:15:27PM +0000, James Morse wrote:
>>>>>> Hi Corentin,
>>>>>>
>>>>>> On 14/02/2020 13:27, LABBE Corentin wrote:
>>>>>>> Since the inclusion of the "enable network support in RPi4 config" serie on uboot, I
>>>>>>> have started to work on adding the rpi4 in kernelCI.
>>>>>>> But I fail to succeed in using a kernel/dtb/ramdisk downloaded via tftp.
>>>>>>>
>>>>>>> Using booti I hit:
>>>>>>> [    0.000000] Linux version 5.6.0-rc1-next-20200212 (clabbe@build2-bionic-1804) (gcc version 7.4.1 20181213 [linaro-7.4-2019.02 revision 56ec6f6b99cc167ff0c2f8e1a2eed33b1edc85d4] (Linaro    GCC 7.4-2019.02)) #66 SMP PREEMPT Wed Feb 12 10:14:20 UTC 2020
>>>>>>> [    0.000000] Machine model: Raspberry Pi 4 Model B
>>>>>>> [    0.000000] earlycon: uart0 at MMIO32 0x00000000fe215040 (options '')
>>>>>>> [    0.000000] printk: bootconsole [uart0] enabled
>>>>>>> [    0.000000] efi: Getting EFI parameters from FDT:
>>>>>>> [    0.000000] efi: UEFI not found.
>>>>>>
>>>>>> So no EFI,
>>>>>>
>>>>>>> [    0.000000] OF: reserved mem: failed to allocate memory for node 'linux,cma'
>>>>>>
>>>>>> Out of memory.
>>>>>>
>>>>>>> [    0.000000] cma: Failed to reserve 32 MiB
>>>>>>> [    0.000000] Kernel panic - not syncing: Failed to allocate page table page
>>>>>>
>>>>>> Out of memory...
>>>>>>
>>>>>>> [    0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 5.6.0-rc1-next-20200212 #66
>>>>>>> [    0.000000] Hardware name: Raspberry Pi 4 Model B (DT)
>>>>>>> [    0.000000] Call trace:
>>>>>>> [    0.000000]  dump_backtrace+0x0/0x1a0
>>>>>>> [    0.000000]  show_stack+0x14/0x20
>>>>>>> [    0.000000]  dump_stack+0xbc/0x104
>>>>>>> [    0.000000]  panic+0x16c/0x37c
>>>>>>> [    0.000000]  early_pgtable_alloc+0x30/0xa0
>>>>>>
>>>>>> ... really early!
>>>>>>
>>>>>>> [    0.000000]  __create_pgd_mapping+0x36c/0x588
>>>>>>> [    0.000000]  map_kernel_segment+0x70/0xa4
>>>>>>> [    0.000000]  paging_init+0xf4/0x528
>>>>>>> [    0.000000]  setup_arch+0x250/0x5d8
>>>>>>> [    0.000000]  start_kernel+0x90/0x6d8
>>>>>>>
>>>>>>>  
>>>>>>> Since the same kernel boot with bootefi and that bootefi lack ramdisk address,
>>>>>>
>>>>>> Booting with EFI will cause linux to use the EFI memory map.
>>>>>>
>>>>>> Does your DT have a memory node? (or does it expect EFI to provide the information)
>>>>>>
>>>>>>
>>>>>>> I tried to add the address in the dtb via:
>>>>>>> fdt addr 0x02400000; fdt resize; fdt set /chosen linux,initrd-start 0x02700000; fdt set /chosen linux,initrd-end 0x10000000; bootefi 0x00080000 0x02400000
>>>>>>> But with that, I get:
>>>>>>> initrd not fully accessible via the linear mapping -- please check your bootloader ...
>>>>>>
>>>>>> So this one is an EFI boot, but you can't find where to put the initramfs such that the
>>>>>> kernel agrees its in memory.
>>>>>>
>>>>>> If you boot with 'efi=debug', linux will print the EFI memory map. Could you compare that
>>>>>> to where U-Boot thinks memory is?
>>>>>>
>>>>>> (it sounds like your DT memory node is missing, and your EFI memory map is surprisingly small)
>>>>>
>>>>> Hello
>>>>>
>>>>> Thanks for your advices.
>>>>>
>>>>> In the dtb of mainline linux:
>>>>> 	/* Will be filled by the bootloader */
>>>>> 	memory@0 {
>>>>> 		device_type = "memory";
>>>>> 		reg = <0 0 0>;
>>>>> 	};
>>>>>
>>>>> In uboot I have:
>>>>> static struct mm_region bcm2711_mem_map[] = {
>>>>>         {
>>>>>                 .virt = 0x00000000UL,
>>>>>                 .phys = 0x00000000UL,
>>>>>                 .size = 0xfe000000UL,
>>>>>                 .attrs = PTE_BLOCK_MEMTYPE(MT_NORMAL) |
>>>>>                          PTE_BLOCK_INNER_SHARE
>>>>>         }, {
>>>>>                 .virt = 0xfc000000UL,
>>>>>                 .phys = 0xfc000000UL,
>>>>>                 .size = 0x03800000UL,
>>>>>                 .attrs = PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) |
>>>>>                          PTE_BLOCK_NON_SHARE |
>>>>>                          PTE_BLOCK_PXN | PTE_BLOCK_UXN
>>>>>         }, {
>>>>>                 /* List terminator */
>>>>>                 0,
>>>>>         }
>>>>> };
>>>>> But I dont know if uboot use that for filling the memory node.
>>>>
>>>> No it doesn't. U-Boot uses the DT from the firmware and passes this to the
>>>> kernel. But it seems you pass instead your own device-tree to the kernel, so you
>>>> will need to update the memory node to show the available memory on you board.
>>>>
>>>
>>> I dont understand, in the Linux commit "ARM: dts: Add minimal Raspberry Pi 4 support" I read:
>>> The RPi 4 is available in 3 different variants (1, 2 and 4 GB RAM), so leave the memory size to zero and let the bootloader take care of it.
>>> But if uboot dont fill that...
>>> So the DTB in mainline is wrong, right ?
>>>
>>
>> How do you pass your DTB to the kernel? Does the FW uses your DTB by putting it
>> as bcm2711-rpi-4-b.dtb in the first FAT partition? Or do you load it from U-Boot
>> afterwards? In the latter case you have to take care to add the needed size of
>> memory. In the first case you use what is the default behavior for U-Boot; the
>> RPi FW updates the node and then passes it to U-Boot then it get's passed to the
>> kernel.
>>
> 
> Hello
> 
> I load the dtb via uboot/tftp.
> On another thread, I got the hint to enable CONFIG_ARCH_FIXUP_FDT_MEMORY and it made my problem solved.

Hm, so should we enable that for all RPi3/4/arm64 configs then?

Regards,
Matthias


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

  reply index

Thread overview: 9+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-02-14 13:27 LABBE Corentin
2020-02-14 18:15 ` James Morse
2020-02-17 10:37   ` LABBE Corentin
2020-02-17 10:50     ` Matthias Brugger
2020-02-17 12:53       ` LABBE Corentin
2020-02-17 13:07         ` Matthias Brugger
2020-02-18 10:01           ` LABBE Corentin
2020-02-18 10:36             ` Matthias Brugger [this message]
2020-02-18 11:08               ` Jaehoon Chung

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=d9727fac-e7fd-7dfb-ce39-da0c5b0d12a2@suse.com \
    --to=mbrugger@suse.com \
    --cc=bcm-kernel-feedback-list@broadcom.com \
    --cc=clabbe@baylibre.com \
    --cc=james.morse@arm.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-rpi-kernel@lists.infradead.org \
    --cc=matthias.bgg@gmail.com \
    --cc=u-boot@lists.denx.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-ARM-Kernel Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-arm-kernel/0 linux-arm-kernel/git/0.git
	git clone --mirror https://lore.kernel.org/linux-arm-kernel/1 linux-arm-kernel/git/1.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-arm-kernel linux-arm-kernel/ https://lore.kernel.org/linux-arm-kernel \
		linux-arm-kernel@lists.infradead.org
	public-inbox-index linux-arm-kernel

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.infradead.lists.linux-arm-kernel


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git