* Re: [PATCH v6 0/5] Add wakeup support and move loopback to TIOCM_LOOP
[not found] <0101016e937a0ef9-36754afa-105c-416f-b308-b5bed0cc0ccb-000000@us-west-2.amazonses.com>
@ 2019-11-22 18:23 ` Stephen Boyd
2019-11-25 12:03 ` Akash Asthana
0 siblings, 1 reply; 3+ messages in thread
From: Stephen Boyd @ 2019-11-22 18:23 UTC (permalink / raw)
To: Akash Asthana, gregkh; +Cc: mgautam, linux-arm-msm, linux-serial, Akash Asthana
Quoting Akash Asthana (2019-11-22 06:18:00)
> This series adds wakeup support over UART RX line and moves loopback
> support to TIOCM_LOOP.
> Patch 1 & 2 reverts the V2 changes for wakeup support on tty-next tip.
> Patch 3 & 4 adds V6 changes for wakeup support.
>
> Akash Asthana (5):
> Revert "tty: serial: qcom_geni_serial: Wakeup over UART RX"
> Revert "tty: serial: qcom_geni_serial: IRQ cleanup"
> tty: serial: qcom_geni_serial: IRQ cleanup
> tty: serial: qcom_geni_serial: Wakeup over UART RX
> tty: serial: qcom_geni_serial: Move loopback support to TIOCM_LOOP
Maybe the reverts aren't necessary? Is it possible to fix up the patches
that are already merged in Greg's tree?
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [PATCH v6 0/5] Add wakeup support and move loopback to TIOCM_LOOP
2019-11-22 18:23 ` [PATCH v6 0/5] Add wakeup support and move loopback to TIOCM_LOOP Stephen Boyd
@ 2019-11-25 12:03 ` Akash Asthana
0 siblings, 0 replies; 3+ messages in thread
From: Akash Asthana @ 2019-11-25 12:03 UTC (permalink / raw)
To: Stephen Boyd, gregkh; +Cc: mgautam, linux-arm-msm, linux-serial
On 11/22/2019 11:53 PM, Stephen Boyd wrote:
> Quoting Akash Asthana (2019-11-22 06:18:00)
>> This series adds wakeup support over UART RX line and moves loopback
>> support to TIOCM_LOOP.
>> Patch 1 & 2 reverts the V2 changes for wakeup support on tty-next tip.
>> Patch 3 & 4 adds V6 changes for wakeup support.
>>
>> Akash Asthana (5):
>> Revert "tty: serial: qcom_geni_serial: Wakeup over UART RX"
>> Revert "tty: serial: qcom_geni_serial: IRQ cleanup"
>> tty: serial: qcom_geni_serial: IRQ cleanup
>> tty: serial: qcom_geni_serial: Wakeup over UART RX
>> tty: serial: qcom_geni_serial: Move loopback support to TIOCM_LOOP
> Maybe the reverts aren't necessary? Is it possible to fix up the patches
> that are already merged in Greg's tree?
Ok, I will fix up already merged patches.
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,\na Linux Foundation Collaborative Project
^ permalink raw reply [flat|nested] 3+ messages in thread
* [PATCH v6 0/5] Add wakeup support and move loopback to TIOCM_LOOP
@ 2019-11-22 14:17 Akash Asthana
0 siblings, 0 replies; 3+ messages in thread
From: Akash Asthana @ 2019-11-22 14:17 UTC (permalink / raw)
To: gregkh; +Cc: swboyd, mgautam, linux-arm-msm, linux-serial, Akash Asthana
This series adds wakeup support over UART RX line and moves loopback
support to TIOCM_LOOP.
Patch 1 & 2 reverts the V2 changes for wakeup support on tty-next tip.
Patch 3 & 4 adds V6 changes for wakeup support.
Akash Asthana (5):
Revert "tty: serial: qcom_geni_serial: Wakeup over UART RX"
Revert "tty: serial: qcom_geni_serial: IRQ cleanup"
tty: serial: qcom_geni_serial: IRQ cleanup
tty: serial: qcom_geni_serial: Wakeup over UART RX
tty: serial: qcom_geni_serial: Move loopback support to TIOCM_LOOP
drivers/tty/serial/qcom_geni_serial.c | 124 ++++++++++++++--------------------
1 file changed, 51 insertions(+), 73 deletions(-)
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,\na Linux Foundation Collaborative Project
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2019-11-25 12:03 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
[not found] <0101016e937a0ef9-36754afa-105c-416f-b308-b5bed0cc0ccb-000000@us-west-2.amazonses.com>
2019-11-22 18:23 ` [PATCH v6 0/5] Add wakeup support and move loopback to TIOCM_LOOP Stephen Boyd
2019-11-25 12:03 ` Akash Asthana
2019-11-22 14:17 Akash Asthana
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).