[PATCH v6 00/14] CPU scaling support for msm8996

[PATCH v6 00/14] CPU scaling support for msm8996

[Ilia Lin]

[v6]
 * Addressed comments from Viresh about:
 ** Comments style
 ** Kconfig bool instead of tristate
 ** DT and documentation style
 ** Resourses deallocation on an error
 ** Typos

[v5]
 * Rebased
 * Addressed comments from Bjorn about SPDX style,
   functions and parameters naming
 * Addressed comments from Viresh DT properties and style, comments style,
   resourses deallocation, documentation placement
 * Addressed comments from Sricharan about unnessesary include
 * Addressed comments from Nicolas
 * Addressed comments from Rob about the commit messages and acks
 * Addressed comments from Mark

[v4]
 * Adressed all comments from Stephen
 * Added CPU regulator support
 * Added qcom-cpufreq-kryo driver

[v3]
 * Rebased on top of the latest PLL driver changes
 * Addressed comment from Rob Herring for bindings

[v2]
 * Addressed comments from Rob Herring for bindings
 * Addressed comments from Mark Rutland for memory barrier
 * Addressed comments from Julien Thierry for clock reenabling condition
 * Tuned the HW configuration for clock frequencies below 600MHz

Clocks:
This series adds support for the CPU clocks on msm8996 devices.
The driver uses the existing PLL drivers and is required to control
the CPU frequency scaling on the MSM8996.

Regulators:
Added SAW regulator support to the SPMI regulator driver. The SAW regulators
will be controlled through special CPU registers instead of direct
SPMI accesses.

Cpufreq:
The qcom-cpufreq-kryo driver is aimed to support different SOC versions.
The driver reads eFuse information and chooses the required OPP subset
by passing the OPP supported-hw parameter.

A previous post of RFC can be found here:
https://patchwork.kernel.org/patch/10377887/

Ilia Lin (11):
  soc: qcom: Separate kryo l2 accessors from PMU driver
  clk: qcom: Add CPU clock driver for msm8996
  clk: qcom: Add DT bindings for CPU clock driver for msm8996
  clk: qcom: Add ACD path to CPU clock driver for msm8996
  dt: qcom: Add opp and thermal to the msm8996
  regulator: qcom_spmi: Add support for SAW
  dt-bindings: qcom_spmi: Add support for SAW documentation
  dt: qcom: Add SAW regulator for 8x96 CPUs
  cpufreq: Add Kryo CPU scaling driver
  dt-bindings: cpufreq: Document operating-points-v2-kryo-cpu
  dt: qcom: Add qcom-cpufreq-kryo driver configuration

Rajendra Nayak (3):
  clk: qcom: Make clk_alpha_pll_configure available to modules
  clk: qcom: cpu-8996: Add support to switch to alternate PLL
  clk: qcom: cpu-8996: Add support to switch below 600Mhz

 .../devicetree/bindings/clock/qcom,kryocc.txt      |  17 +
 .../devicetree/bindings/opp/kryo-cpufreq.txt       | 680 +++++++++++++++++++++
 .../bindings/regulator/qcom,spmi-regulator.txt     |  45 ++
 arch/arm64/boot/dts/qcom/apq8096-db820c.dts        |   2 +-
 arch/arm64/boot/dts/qcom/msm8996.dtsi              | 650 +++++++++++++++++++-
 drivers/clk/clk-fixed-factor.c                     |   2 +-
 drivers/clk/qcom/Kconfig                           |   9 +
 drivers/clk/qcom/Makefile                          |   1 +
 drivers/clk/qcom/clk-alpha-pll.c                   |   1 +
 drivers/clk/qcom/clk-alpha-pll.h                   |   6 +
 drivers/clk/qcom/clk-cpu-8996.c                    | 519 ++++++++++++++++
 drivers/cpufreq/Kconfig.arm                        |  11 +
 drivers/cpufreq/Makefile                           |   1 +
 drivers/cpufreq/cpufreq-dt-platdev.c               |   3 +
 drivers/cpufreq/qcom-cpufreq-kryo.c                | 148 +++++
 drivers/perf/Kconfig                               |   1 +
 drivers/perf/qcom_l2_pmu.c                         |  90 +--
 drivers/regulator/qcom_spmi-regulator.c            | 133 +++-
 drivers/soc/qcom/Kconfig                           |   3 +
 drivers/soc/qcom/Makefile                          |   1 +
 drivers/soc/qcom/kryo-l2-accessors.c               |  65 ++
 include/soc/qcom/kryo-l2-accessors.h               |  21 +
 22 files changed, 2329 insertions(+), 80 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/clock/qcom,kryocc.txt
 create mode 100644 Documentation/devicetree/bindings/opp/kryo-cpufreq.txt
 create mode 100644 drivers/clk/qcom/clk-cpu-8996.c
 create mode 100644 drivers/cpufreq/qcom-cpufreq-kryo.c
 create mode 100644 drivers/soc/qcom/kryo-l2-accessors.c
 create mode 100644 include/soc/qcom/kryo-l2-accessors.h

-- 
1.9.1

[PATCH v6 01/14] soc: qcom: Separate kryo l2 accessors from PMU driver

[Ilia Lin]

The driver provides kernel level API for other drivers
to access the MSM8996 L2 cache registers.
Separating the L2 access code from the PMU driver and
making it public to allow other drivers use it.
The accesses must be separated with a single spinlock,
maintained in this driver.

Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
---
 drivers/perf/Kconfig                 |  1 +
 drivers/perf/qcom_l2_pmu.c           | 90 ++++++++++--------------------------
 drivers/soc/qcom/Kconfig             |  3 ++
 drivers/soc/qcom/Makefile            |  1 +
 drivers/soc/qcom/kryo-l2-accessors.c | 65 ++++++++++++++++++++++++++
 include/soc/qcom/kryo-l2-accessors.h | 21 +++++++++
 6 files changed, 115 insertions(+), 66 deletions(-)
 create mode 100644 drivers/soc/qcom/kryo-l2-accessors.c
 create mode 100644 include/soc/qcom/kryo-l2-accessors.h

diff --git a/drivers/perf/Kconfig b/drivers/perf/Kconfig
index 28bb5a0..561252a 100644
--- a/drivers/perf/Kconfig
+++ b/drivers/perf/Kconfig
@@ -69,6 +69,7 @@ config HISI_PMU
 config QCOM_L2_PMU
 	bool "Qualcomm Technologies L2-cache PMU"
 	depends on ARCH_QCOM && ARM64 && ACPI
+	select QCOM_KRYO_L2_ACCESSORS
 	  help
 	  Provides support for the L2 cache performance monitor unit (PMU)
 	  in Qualcomm Technologies processors.
diff --git a/drivers/perf/qcom_l2_pmu.c b/drivers/perf/qcom_l2_pmu.c
index 842135c..cc31f51 100644
--- a/drivers/perf/qcom_l2_pmu.c
+++ b/drivers/perf/qcom_l2_pmu.c
@@ -31,6 +31,7 @@
 #include <asm/barrier.h>
 #include <asm/local64.h>
 #include <asm/sysreg.h>
+#include <soc/qcom/kryo-l2-accessors.h>
 
 #define MAX_L2_CTRS             9
 
@@ -87,8 +88,6 @@
 #define L2_COUNTER_RELOAD       BIT_ULL(31)
 #define L2_CYCLE_COUNTER_RELOAD BIT_ULL(63)
 
-#define L2CPUSRSELR_EL1         sys_reg(3, 3, 15, 0, 6)
-#define L2CPUSRDR_EL1           sys_reg(3, 3, 15, 0, 7)
 
 #define reg_idx(reg, i)         (((i) * IA_L2_REG_OFFSET) + reg##_BASE)
 
@@ -107,48 +106,7 @@
 #define L2_EVENT_STREX                     0x421
 #define L2_EVENT_CLREX                     0x422
 
-static DEFINE_RAW_SPINLOCK(l2_access_lock);
 
-/**
- * set_l2_indirect_reg: write value to an L2 register
- * @reg: Address of L2 register.
- * @value: Value to be written to register.
- *
- * Use architecturally required barriers for ordering between system register
- * accesses
- */
-static void set_l2_indirect_reg(u64 reg, u64 val)
-{
-	unsigned long flags;
-
-	raw_spin_lock_irqsave(&l2_access_lock, flags);
-	write_sysreg_s(reg, L2CPUSRSELR_EL1);
-	isb();
-	write_sysreg_s(val, L2CPUSRDR_EL1);
-	isb();
-	raw_spin_unlock_irqrestore(&l2_access_lock, flags);
-}
-
-/**
- * get_l2_indirect_reg: read an L2 register value
- * @reg: Address of L2 register.
- *
- * Use architecturally required barriers for ordering between system register
- * accesses
- */
-static u64 get_l2_indirect_reg(u64 reg)
-{
-	u64 val;
-	unsigned long flags;
-
-	raw_spin_lock_irqsave(&l2_access_lock, flags);
-	write_sysreg_s(reg, L2CPUSRSELR_EL1);
-	isb();
-	val = read_sysreg_s(L2CPUSRDR_EL1);
-	raw_spin_unlock_irqrestore(&l2_access_lock, flags);
-
-	return val;
-}
 
 struct cluster_pmu;
 
@@ -219,28 +177,28 @@ static inline struct cluster_pmu *get_cluster_pmu(
 static void cluster_pmu_reset(void)
 {
 	/* Reset all counters */
-	set_l2_indirect_reg(L2PMCR, L2PMCR_RESET_ALL);
-	set_l2_indirect_reg(L2PMCNTENCLR, l2_counter_present_mask);
-	set_l2_indirect_reg(L2PMINTENCLR, l2_counter_present_mask);
-	set_l2_indirect_reg(L2PMOVSCLR, l2_counter_present_mask);
+	kryo_l2_set_indirect_reg(L2PMCR, L2PMCR_RESET_ALL);
+	kryo_l2_set_indirect_reg(L2PMCNTENCLR, l2_counter_present_mask);
+	kryo_l2_set_indirect_reg(L2PMINTENCLR, l2_counter_present_mask);
+	kryo_l2_set_indirect_reg(L2PMOVSCLR, l2_counter_present_mask);
 }
 
 static inline void cluster_pmu_enable(void)
 {
-	set_l2_indirect_reg(L2PMCR, L2PMCR_COUNTERS_ENABLE);
+	kryo_l2_set_indirect_reg(L2PMCR, L2PMCR_COUNTERS_ENABLE);
 }
 
 static inline void cluster_pmu_disable(void)
 {
-	set_l2_indirect_reg(L2PMCR, L2PMCR_COUNTERS_DISABLE);
+	kryo_l2_set_indirect_reg(L2PMCR, L2PMCR_COUNTERS_DISABLE);
 }
 
 static inline void cluster_pmu_counter_set_value(u32 idx, u64 value)
 {
 	if (idx == l2_cycle_ctr_idx)
-		set_l2_indirect_reg(L2PMCCNTR, value);
+		kryo_l2_set_indirect_reg(L2PMCCNTR, value);
 	else
-		set_l2_indirect_reg(reg_idx(IA_L2PMXEVCNTR, idx), value);
+		kryo_l2_set_indirect_reg(reg_idx(IA_L2PMXEVCNTR, idx), value);
 }
 
 static inline u64 cluster_pmu_counter_get_value(u32 idx)
@@ -248,46 +206,46 @@ static inline u64 cluster_pmu_counter_get_value(u32 idx)
 	u64 value;
 
 	if (idx == l2_cycle_ctr_idx)
-		value = get_l2_indirect_reg(L2PMCCNTR);
+		value = kryo_l2_get_indirect_reg(L2PMCCNTR);
 	else
-		value = get_l2_indirect_reg(reg_idx(IA_L2PMXEVCNTR, idx));
+		value = kryo_l2_get_indirect_reg(reg_idx(IA_L2PMXEVCNTR, idx));
 
 	return value;
 }
 
 static inline void cluster_pmu_counter_enable(u32 idx)
 {
-	set_l2_indirect_reg(L2PMCNTENSET, idx_to_reg_bit(idx));
+	kryo_l2_set_indirect_reg(L2PMCNTENSET, idx_to_reg_bit(idx));
 }
 
 static inline void cluster_pmu_counter_disable(u32 idx)
 {
-	set_l2_indirect_reg(L2PMCNTENCLR, idx_to_reg_bit(idx));
+	kryo_l2_set_indirect_reg(L2PMCNTENCLR, idx_to_reg_bit(idx));
 }
 
 static inline void cluster_pmu_counter_enable_interrupt(u32 idx)
 {
-	set_l2_indirect_reg(L2PMINTENSET, idx_to_reg_bit(idx));
+	kryo_l2_set_indirect_reg(L2PMINTENSET, idx_to_reg_bit(idx));
 }
 
 static inline void cluster_pmu_counter_disable_interrupt(u32 idx)
 {
-	set_l2_indirect_reg(L2PMINTENCLR, idx_to_reg_bit(idx));
+	kryo_l2_set_indirect_reg(L2PMINTENCLR, idx_to_reg_bit(idx));
 }
 
 static inline void cluster_pmu_set_evccntcr(u32 val)
 {
-	set_l2_indirect_reg(L2PMCCNTCR, val);
+	kryo_l2_set_indirect_reg(L2PMCCNTCR, val);
 }
 
 static inline void cluster_pmu_set_evcntcr(u32 ctr, u32 val)
 {
-	set_l2_indirect_reg(reg_idx(IA_L2PMXEVCNTCR, ctr), val);
+	kryo_l2_set_indirect_reg(reg_idx(IA_L2PMXEVCNTCR, ctr), val);
 }
 
 static inline void cluster_pmu_set_evtyper(u32 ctr, u32 val)
 {
-	set_l2_indirect_reg(reg_idx(IA_L2PMXEVTYPER, ctr), val);
+	kryo_l2_set_indirect_reg(reg_idx(IA_L2PMXEVTYPER, ctr), val);
 }
 
 static void cluster_pmu_set_resr(struct cluster_pmu *cluster,
@@ -303,11 +261,11 @@ static void cluster_pmu_set_resr(struct cluster_pmu *cluster,
 
 	spin_lock_irqsave(&cluster->pmu_lock, flags);
 
-	resr_val = get_l2_indirect_reg(L2PMRESR);
+	resr_val = kryo_l2_get_indirect_reg(L2PMRESR);
 	resr_val &= ~(L2PMRESR_GROUP_MASK << shift);
 	resr_val |= field;
 	resr_val |= L2PMRESR_EN;
-	set_l2_indirect_reg(L2PMRESR, resr_val);
+	kryo_l2_set_indirect_reg(L2PMRESR, resr_val);
 
 	spin_unlock_irqrestore(&cluster->pmu_lock, flags);
 }
@@ -323,14 +281,14 @@ static inline void cluster_pmu_set_evfilter_sys_mode(u32 ctr)
 		   L2PMXEVFILTER_ORGFILTER_IDINDEP |
 		   L2PMXEVFILTER_ORGFILTER_ALL;
 
-	set_l2_indirect_reg(reg_idx(IA_L2PMXEVFILTER, ctr), val);
+	kryo_l2_set_indirect_reg(reg_idx(IA_L2PMXEVFILTER, ctr), val);
 }
 
 static inline u32 cluster_pmu_getreset_ovsr(void)
 {
-	u32 result = get_l2_indirect_reg(L2PMOVSSET);
+	u32 result = kryo_l2_get_indirect_reg(L2PMOVSSET);
 
-	set_l2_indirect_reg(L2PMOVSCLR, result);
+	kryo_l2_set_indirect_reg(L2PMOVSCLR, result);
 	return result;
 }
 
@@ -783,7 +741,7 @@ static int get_num_counters(void)
 {
 	int val;
 
-	val = get_l2_indirect_reg(L2PMCR);
+	val = kryo_l2_get_indirect_reg(L2PMCR);
 
 	/*
 	 * Read number of counters from L2PMCR and add 1
diff --git a/drivers/soc/qcom/Kconfig b/drivers/soc/qcom/Kconfig
index 7093fe7..0567dff 100644
--- a/drivers/soc/qcom/Kconfig
+++ b/drivers/soc/qcom/Kconfig
@@ -39,6 +39,9 @@ config QCOM_GSBI
           functions for connecting the underlying serial UART, SPI, and I2C
           devices to the output pins.
 
+config QCOM_KRYO_L2_ACCESSORS
+       bool
+
 config QCOM_MDT_LOADER
 	tristate
 	select QCOM_SCM
diff --git a/drivers/soc/qcom/Makefile b/drivers/soc/qcom/Makefile
index cbf414c..e4d3f5a 100644
--- a/drivers/soc/qcom/Makefile
+++ b/drivers/soc/qcom/Makefile
@@ -14,3 +14,4 @@ obj-$(CONFIG_QCOM_SMEM_STATE) += smem_state.o
 obj-$(CONFIG_QCOM_SMP2P)	+= smp2p.o
 obj-$(CONFIG_QCOM_SMSM)	+= smsm.o
 obj-$(CONFIG_QCOM_WCNSS_CTRL) += wcnss_ctrl.o
+obj-$(CONFIG_QCOM_KRYO_L2_ACCESSORS) +=	kryo-l2-accessors.o
diff --git a/drivers/soc/qcom/kryo-l2-accessors.c b/drivers/soc/qcom/kryo-l2-accessors.c
new file mode 100644
index 0000000..d35a860
--- /dev/null
+++ b/drivers/soc/qcom/kryo-l2-accessors.c
@@ -0,0 +1,65 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2014-2015, 2018, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/spinlock.h>
+#include <asm/sysreg.h>
+#include <soc/qcom/kryo-l2-accessors.h>
+
+#define L2CPUSRSELR_EL1         sys_reg(3, 3, 15, 0, 6)
+#define L2CPUSRDR_EL1           sys_reg(3, 3, 15, 0, 7)
+
+static DEFINE_RAW_SPINLOCK(l2_access_lock);
+
+/**
+ * kryo_l2_set_indirect_reg() - write value to an L2 register
+ * @reg: Address of L2 register.
+ * @value: Value to be written to register.
+ *
+ * Use architecturally required barriers for ordering between system register
+ * accesses, and system registers with respect to device memory
+ */
+void kryo_l2_set_indirect_reg(u64 reg, u64 val)
+{
+	unsigned long flags;
+
+	raw_spin_lock_irqsave(&l2_access_lock, flags);
+	write_sysreg_s(reg, L2CPUSRSELR_EL1);
+	isb();
+	write_sysreg_s(val, L2CPUSRDR_EL1);
+	isb();
+	raw_spin_unlock_irqrestore(&l2_access_lock, flags);
+}
+EXPORT_SYMBOL(kryo_l2_set_indirect_reg);
+
+/**
+ * kryo_l2_get_indirect_reg() - read an L2 register value
+ * @reg: Address of L2 register.
+ *
+ * Use architecturally required barriers for ordering between system register
+ * accesses, and system registers with respect to device memory
+ */
+u64 kryo_l2_get_indirect_reg(u64 reg)
+{
+	u64 val;
+	unsigned long flags;
+
+	raw_spin_lock_irqsave(&l2_access_lock, flags);
+	write_sysreg_s(reg, L2CPUSRSELR_EL1);
+	isb();
+	val = read_sysreg_s(L2CPUSRDR_EL1);
+	raw_spin_unlock_irqrestore(&l2_access_lock, flags);
+
+	return val;
+}
+EXPORT_SYMBOL(kryo_l2_get_indirect_reg);
diff --git a/include/soc/qcom/kryo-l2-accessors.h b/include/soc/qcom/kryo-l2-accessors.h
new file mode 100644
index 0000000..0840e87
--- /dev/null
+++ b/include/soc/qcom/kryo-l2-accessors.h
@@ -0,0 +1,21 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2018, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __SOC_ARCH_QCOM_KRYO_L2_ACCESSORS_H
+#define __SOC_ARCH_QCOM_KRYO_L2_ACCESSORS_H
+
+void kryo_l2_set_indirect_reg(u64 reg, u64 val);
+u64 kryo_l2_get_indirect_reg(u64 reg);
+
+#endif
-- 
1.9.1

[PATCH v6 02/14] clk: qcom: Make clk_alpha_pll_configure available to modules

[Ilia Lin]

From: Rajendra Nayak <rnayak@codeaurora.org>

Allow clk_alpha_pll_configure to be called from loadable
kernel modules.

Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
---
 drivers/clk/qcom/clk-alpha-pll.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/clk/qcom/clk-alpha-pll.c b/drivers/clk/qcom/clk-alpha-pll.c
index 9722b70..57f2084 100644
--- a/drivers/clk/qcom/clk-alpha-pll.c
+++ b/drivers/clk/qcom/clk-alpha-pll.c
@@ -228,6 +228,7 @@ void clk_alpha_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,
 	if (pll->flags & SUPPORTS_FSM_MODE)
 		qcom_pll_set_fsm_mode(regmap, PLL_MODE(pll), 6, 0);
 }
+EXPORT_SYMBOL_GPL(clk_alpha_pll_configure);
 
 static int clk_alpha_pll_hwfsm_enable(struct clk_hw *hw)
 {
-- 
1.9.1

[PATCH v6 03/14] clk: qcom: Add CPU clock driver for msm8996

[Ilia Lin]

Each of the CPU clusters (Power and Perf) on msm8996 are
clocked via 2 PLLs, a primary and alternate. There are also
2 Mux'es, a primary and secondary all connected together
as shown below

                             +-------+
              XO             |       |
          +------------------>0      |
                             |       |
                   PLL/2     | SMUX  +----+
                     +------->1      |    |
                     |       |       |    |
                     |       +-------+    |    +-------+
                     |                    +---->0      |
                     |                         |       |
+---------------+    |             +----------->1      | CPU clk
|Primary PLL    +----+ PLL_EARLY   |           |       +------>
|               +------+-----------+    +------>2 PMUX |
+---------------+      |                |      |       |
                       |   +------+     |   +-->3      |
                       +--^+  ACD +-----+   |  +-------+
+---------------+          +------+         |
|Alt PLL        |                           |
|               +---------------------------+
+---------------+         PLL_EARLY

The primary PLL is what drives the CPU clk, except for times
when we are reprogramming the PLL itself (for rate changes) when
we temporarily switch to an alternate PLL. A subsequent patch adds
support to switch between primary and alternate PLL during rate
changes.

The primary PLL operates on a single VCO range, between 600MHz
and 3GHz. However the CPUs do support OPPs with frequencies
between 300MHz and 600MHz. In order to support running the CPUs
at those frequencies we end up having to lock the PLL at twice
the rate and drive the CPU clk via the PLL/2 output and SMUX.

So for frequencies above 600MHz we follow the following path
 Primary PLL --> PLL_EARLY --> PMUX(1) --> CPU clk
and for frequencies between 300MHz and 600MHz we follow
 Primary PLL --> PLL/2 --> SMUX(1) --> PMUX(0) --> CPU clk
Support for this is added in a subsequent patch as well.

ACD stands for Adaptive Clock Distribution and is used to
detect voltage droops. We do not add support for ACD as yet.

Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
---
 drivers/clk/clk-fixed-factor.c   |   2 +-
 drivers/clk/qcom/Kconfig         |   9 +
 drivers/clk/qcom/Makefile        |   1 +
 drivers/clk/qcom/clk-alpha-pll.h |   6 +
 drivers/clk/qcom/clk-cpu-8996.c  | 412 +++++++++++++++++++++++++++++++++++++++
 5 files changed, 429 insertions(+), 1 deletion(-)
 create mode 100644 drivers/clk/qcom/clk-cpu-8996.c

diff --git a/drivers/clk/clk-fixed-factor.c b/drivers/clk/clk-fixed-factor.c
index a5d402d..8e39bda 100644
--- a/drivers/clk/clk-fixed-factor.c
+++ b/drivers/clk/clk-fixed-factor.c
@@ -94,7 +94,7 @@ struct clk_hw *clk_hw_register_fixed_factor(struct device *dev,
 	init.num_parents = 1;
 
 	hw = &fix->hw;
-	ret = clk_hw_register(dev, hw);
+	ret = devm_clk_hw_register(dev, hw);
 	if (ret) {
 		kfree(fix);
 		hw = ERR_PTR(ret);
diff --git a/drivers/clk/qcom/Kconfig b/drivers/clk/qcom/Kconfig
index e42e1af..866ce1f 100644
--- a/drivers/clk/qcom/Kconfig
+++ b/drivers/clk/qcom/Kconfig
@@ -33,6 +33,15 @@ config QCOM_CLK_APCS_MSM8916
 	  Say Y if you want to support CPU frequency scaling on devices
 	  such as msm8916.
 
+config QCOM_CLK_APCC_MSM8996
+	tristate "MSM8996 CPU Clock Controller"
+	depends on COMMON_CLK_QCOM
+	select QCOM_KRYO_L2_ACCESSORS
+	help
+	  Support for the CPU clock controller on msm8996 devices.
+	  Say Y if you want to support CPU clock scaling using CPUfreq
+	  drivers for dyanmic power management.
+
 config QCOM_CLK_RPM
 	tristate "RPM based Clock Controller"
 	depends on COMMON_CLK_QCOM && MFD_QCOM_RPM
diff --git a/drivers/clk/qcom/Makefile b/drivers/clk/qcom/Makefile
index 7c09ab1..a822fc8 100644
--- a/drivers/clk/qcom/Makefile
+++ b/drivers/clk/qcom/Makefile
@@ -36,6 +36,7 @@ obj-$(CONFIG_MSM_MMCC_8974) += mmcc-msm8974.o
 obj-$(CONFIG_MSM_MMCC_8996) += mmcc-msm8996.o
 obj-$(CONFIG_QCOM_A53PLL) += a53-pll.o
 obj-$(CONFIG_QCOM_CLK_APCS_MSM8916) += apcs-msm8916.o
+obj-$(CONFIG_QCOM_CLK_APCC_MSM8996) += clk-cpu-8996.o
 obj-$(CONFIG_QCOM_CLK_RPM) += clk-rpm.o
 obj-$(CONFIG_QCOM_CLK_SMD_RPM) += clk-smd-rpm.o
 obj-$(CONFIG_SPMI_PMIC_CLKDIV) += clk-spmi-pmic-div.o
diff --git a/drivers/clk/qcom/clk-alpha-pll.h b/drivers/clk/qcom/clk-alpha-pll.h
index f981b48..9ce2a32 100644
--- a/drivers/clk/qcom/clk-alpha-pll.h
+++ b/drivers/clk/qcom/clk-alpha-pll.h
@@ -50,6 +50,12 @@ struct pll_vco {
 	u32 val;
 };
 
+#define VCO(a, b, c) { \
+	.val = a,\
+	.min_freq = b,\
+	.max_freq = c,\
+}
+
 /**
  * struct clk_alpha_pll - phase locked loop (PLL)
  * @offset: base address of registers
diff --git a/drivers/clk/qcom/clk-cpu-8996.c b/drivers/clk/qcom/clk-cpu-8996.c
new file mode 100644
index 0000000..beb97eb
--- /dev/null
+++ b/drivers/clk/qcom/clk-cpu-8996.c
@@ -0,0 +1,412 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2018, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+/*
+ * Each of the CPU clusters (Power and Perf) on msm8996 are
+ * clocked via 2 PLLs, a primary and alternate. There are also
+ * 2 Mux'es, a primary and secondary all connected together
+ * as shown below
+ *
+ *                              +-------+
+ *               XO             |       |
+ *           +------------------>0      |
+ *                              |       |
+ *                    PLL/2     | SMUX  +----+
+ *                      +------->1      |    |
+ *                      |       |       |    |
+ *                      |       +-------+    |    +-------+
+ *                      |                    +---->0      |
+ *                      |                         |       |
+ * +---------------+    |             +----------->1      | CPU clk
+ * |Primary PLL    +----+ PLL_EARLY   |           |       +------>
+ * |               +------+-----------+    +------>2 PMUX |
+ * +---------------+      |                |      |       |
+ *                        |   +------+     |   +-->3      |
+ *                        +--^+  ACD +-----+   |  +-------+
+ * +---------------+          +------+         |
+ * |Alt PLL        |                           |
+ * |               +---------------------------+
+ * +---------------+         PLL_EARLY
+ *
+ * The primary PLL is what drives the CPU clk, except for times
+ * when we are reprogramming the PLL itself (for rate changes) when
+ * we temporarily switch to an alternate PLL. A subsequent patch adds
+ * support to switch between primary and alternate PLL during rate
+ * changes.
+ *
+ * The primary PLL operates on a single VCO range, between 600MHz
+ * and 3GHz. However the CPUs do support OPPs with frequencies
+ * between 300MHz and 600MHz. In order to support running the CPUs
+ * at those frequencies we end up having to lock the PLL at twice
+ * the rate and drive the CPU clk via the PLL/2 output and SMUX.
+ *
+ * So for frequencies above 600MHz we follow the following path
+ *  Primary PLL --> PLL_EARLY --> PMUX(1) --> CPU clk
+ * and for frequencies between 300MHz and 600MHz we follow
+ *  Primary PLL --> PLL/2 --> SMUX(1) --> PMUX(0) --> CPU clk
+ * Support for this is added in a subsequent patch as well.
+ *
+ * ACD stands for Adaptive Clock Distribution and is used to
+ * detect voltage droops. We do not add support for ACD as yet.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#include "clk-alpha-pll.h"
+#include "clk-regmap.h"
+
+enum _pmux_input {
+	DIV_2_INDEX = 0,
+	PLL_INDEX,
+	ACD_INDEX,
+	ALT_INDEX,
+	NUM_OF_PMUX_INPUTS
+};
+
+static const u8 prim_pll_regs[PLL_OFF_MAX_REGS] = {
+       [PLL_OFF_L_VAL] = 0x04,
+       [PLL_OFF_ALPHA_VAL] = 0x08,
+       [PLL_OFF_USER_CTL] = 0x10,
+       [PLL_OFF_CONFIG_CTL] = 0x18,
+       [PLL_OFF_CONFIG_CTL_U] = 0x1c,
+       [PLL_OFF_TEST_CTL] = 0x20,
+       [PLL_OFF_TEST_CTL_U] = 0x24,
+       [PLL_OFF_STATUS] = 0x28,
+};
+
+static const u8 alt_pll_regs[PLL_OFF_MAX_REGS] = {
+       [PLL_OFF_L_VAL] = 0x04,
+       [PLL_OFF_ALPHA_VAL] = 0x08,
+       [PLL_OFF_ALPHA_VAL_U] = 0x0c,
+       [PLL_OFF_USER_CTL] = 0x10,
+       [PLL_OFF_USER_CTL_U] = 0x14,
+       [PLL_OFF_CONFIG_CTL] = 0x18,
+       [PLL_OFF_TEST_CTL] = 0x20,
+       [PLL_OFF_TEST_CTL_U] = 0x24,
+       [PLL_OFF_STATUS] = 0x28,
+};
+
+/* PLLs */
+
+static const struct alpha_pll_config hfpll_config = {
+	.l = 60,
+	.config_ctl_val = 0x200d4828,
+	.config_ctl_hi_val = 0x006,
+	.pre_div_mask = BIT(12),
+	.post_div_mask = 0x3 << 8,
+	.main_output_mask = BIT(0),
+	.early_output_mask = BIT(3),
+};
+
+static struct clk_alpha_pll perfcl_pll = {
+	.offset = 0x80000,
+	.regs = prim_pll_regs,
+	.flags = SUPPORTS_DYNAMIC_UPDATE | SUPPORTS_FSM_MODE,
+	.clkr.hw.init = &(struct clk_init_data){
+		.name = "perfcl_pll",
+		.parent_names = (const char *[]){ "xo" },
+		.num_parents = 1,
+		.ops = &clk_alpha_pll_huayra_ops,
+	},
+};
+
+static struct clk_alpha_pll pwrcl_pll = {
+	.offset = 0x0,
+	.regs = prim_pll_regs,
+	.flags = SUPPORTS_DYNAMIC_UPDATE | SUPPORTS_FSM_MODE,
+	.clkr.hw.init = &(struct clk_init_data){
+		.name = "pwrcl_pll",
+		.parent_names = (const char *[]){ "xo" },
+		.num_parents = 1,
+		.ops = &clk_alpha_pll_huayra_ops,
+	},
+};
+
+static const struct pll_vco alt_pll_vco_modes[] = {
+	VCO(3,  250000000,  500000000),
+	VCO(2,  500000000,  750000000),
+	VCO(1,  750000000, 1000000000),
+	VCO(0, 1000000000, 2150400000),
+};
+
+static const struct alpha_pll_config altpll_config = {
+	.l = 16,
+	.vco_val = 0x3 << 20,
+	.vco_mask = 0x3 << 20,
+	.config_ctl_val = 0x4001051b,
+	.post_div_mask = 0x3 << 8,
+	.post_div_val = 0x1,
+	.main_output_mask = BIT(0),
+	.early_output_mask = BIT(3),
+};
+
+static struct clk_alpha_pll perfcl_alt_pll = {
+	.offset = 0x80100,
+	.regs = alt_pll_regs,
+	.vco_table = alt_pll_vco_modes,
+	.num_vco = ARRAY_SIZE(alt_pll_vco_modes),
+	.flags = SUPPORTS_OFFLINE_REQ | SUPPORTS_FSM_MODE,
+	.clkr.hw.init = &(struct clk_init_data) {
+		.name = "perfcl_alt_pll",
+		.parent_names = (const char *[]){ "xo" },
+		.num_parents = 1,
+		.ops = &clk_alpha_pll_hwfsm_ops,
+	},
+};
+
+static struct clk_alpha_pll pwrcl_alt_pll = {
+	.offset = 0x100,
+	.regs = alt_pll_regs,
+	.vco_table = alt_pll_vco_modes,
+	.num_vco = ARRAY_SIZE(alt_pll_vco_modes),
+	.flags = SUPPORTS_OFFLINE_REQ | SUPPORTS_FSM_MODE,
+	.clkr.hw.init = &(struct clk_init_data) {
+		.name = "pwrcl_alt_pll",
+		.parent_names = (const char *[]){ "xo" },
+		.num_parents = 1,
+		.ops = &clk_alpha_pll_hwfsm_ops,
+	},
+};
+
+/* Mux'es */
+
+struct clk_cpu_8996_mux {
+	u32	reg;
+	u8	shift;
+	u8	width;
+	struct clk_hw	*pll;
+	struct clk_regmap clkr;
+};
+
+static inline
+struct clk_cpu_8996_mux *to_clk_cpu_8996_mux_hw(struct clk_hw *hw)
+{
+	return container_of(to_clk_regmap(hw), struct clk_cpu_8996_mux, clkr);
+}
+
+static u8 clk_cpu_8996_mux_get_parent(struct clk_hw *hw)
+{
+	u32 val;
+	struct clk_regmap *clkr = to_clk_regmap(hw);
+	struct clk_cpu_8996_mux *cpuclk = to_clk_cpu_8996_mux_hw(hw);
+	u32 mask = (u32)GENMASK(cpuclk->width - 1, 0);
+
+	regmap_read(clkr->regmap, cpuclk->reg, &val);
+	val >>= (u32)(cpuclk->shift);
+
+	return (u8)(val & mask);
+}
+
+static int clk_cpu_8996_mux_set_parent(struct clk_hw *hw, u8 index)
+{
+	u32 val;
+	struct clk_regmap *clkr = to_clk_regmap(hw);
+	struct clk_cpu_8996_mux *cpuclk = to_clk_cpu_8996_mux_hw(hw);
+	unsigned int mask = GENMASK(cpuclk->width + cpuclk->shift - 1,
+				    cpuclk->shift);
+
+	val = (u32)index;
+	val <<= (u32)(cpuclk->shift);
+
+	return regmap_update_bits(clkr->regmap, cpuclk->reg, mask, val);
+}
+
+static int
+clk_cpu_8996_mux_determine_rate(struct clk_hw *hw, struct clk_rate_request *req)
+{
+	struct clk_cpu_8996_mux *cpuclk = to_clk_cpu_8996_mux_hw(hw);
+	struct clk_hw *parent = cpuclk->pll;
+
+	req->best_parent_rate = clk_hw_round_rate(parent, req->rate);
+	req->best_parent_hw = parent;
+
+	return 0;
+}
+
+const struct clk_ops clk_cpu_8996_mux_ops = {
+	.set_parent = clk_cpu_8996_mux_set_parent,
+	.get_parent = clk_cpu_8996_mux_get_parent,
+	.determine_rate = clk_cpu_8996_mux_determine_rate,
+};
+
+static struct clk_cpu_8996_mux pwrcl_smux = {
+	.reg = 0x40,
+	.shift = 2,
+	.width = 2,
+	.clkr.hw.init = &(struct clk_init_data) {
+		.name = "pwrcl_smux",
+		.parent_names = (const char *[]){
+			"xo",
+			"pwrcl_pll_main",
+		},
+		.num_parents = 2,
+		.ops = &clk_cpu_8996_mux_ops,
+		.flags = CLK_SET_RATE_PARENT,
+	},
+};
+
+static struct clk_cpu_8996_mux perfcl_smux = {
+	.reg = 0x80040,
+	.shift = 2,
+	.width = 2,
+	.clkr.hw.init = &(struct clk_init_data) {
+		.name = "perfcl_smux",
+		.parent_names = (const char *[]){
+			"xo",
+			"perfcl_pll_main",
+		},
+		.num_parents = 2,
+		.ops = &clk_cpu_8996_mux_ops,
+		.flags = CLK_SET_RATE_PARENT,
+	},
+};
+
+static struct clk_cpu_8996_mux pwrcl_pmux = {
+	.reg = 0x40,
+	.shift = 0,
+	.width = 2,
+	.pll = &pwrcl_pll.clkr.hw,
+	.clkr.hw.init = &(struct clk_init_data) {
+		.name = "pwrcl_pmux",
+		.parent_names = (const char *[]){
+			"pwrcl_smux",
+			"pwrcl_pll",
+			"pwrcl_pll_acd",
+			"pwrcl_alt_pll",
+		},
+		.num_parents = 4,
+		.ops = &clk_cpu_8996_mux_ops,
+		.flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
+	},
+};
+
+static struct clk_cpu_8996_mux perfcl_pmux = {
+	.reg = 0x80040,
+	.shift = 0,
+	.width = 2,
+	.pll = &perfcl_pll.clkr.hw,
+	.clkr.hw.init = &(struct clk_init_data) {
+		.name = "perfcl_pmux",
+		.parent_names = (const char *[]){
+			"perfcl_smux",
+			"perfcl_pll",
+			"perfcl_pll_acd",
+			"perfcl_alt_pll",
+		},
+		.num_parents = 4,
+		.ops = &clk_cpu_8996_mux_ops,
+		.flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
+	},
+};
+
+static const struct regmap_config cpu_msm8996_regmap_config = {
+	.reg_bits		= 32,
+	.reg_stride		= 4,
+	.val_bits		= 32,
+	.max_register		= 0x80210,
+	.fast_io		= true,
+	.val_format_endian	= REGMAP_ENDIAN_LITTLE,
+};
+
+struct clk_regmap *clks[] = {
+	&perfcl_pll.clkr,
+	&pwrcl_pll.clkr,
+	&perfcl_alt_pll.clkr,
+	&pwrcl_alt_pll.clkr,
+	&perfcl_smux.clkr,
+	&pwrcl_smux.clkr,
+	&perfcl_pmux.clkr,
+	&pwrcl_pmux.clkr,
+};
+
+static int
+qcom_cpu_clk_msm8996_register_clks(struct device *dev, struct regmap *regmap)
+{
+	int i, ret;
+
+	perfcl_smux.pll = clk_hw_register_fixed_factor(dev, "perfcl_pll_main",
+						       "perfcl_pll",
+						   CLK_SET_RATE_PARENT, 1, 2);
+
+	pwrcl_smux.pll = clk_hw_register_fixed_factor(dev, "pwrcl_pll_main",
+						      "pwrcl_pll",
+						   CLK_SET_RATE_PARENT, 1, 2);
+
+	for (i = 0; i < ARRAY_SIZE(clks); i++) {
+		ret = devm_clk_register_regmap(dev, clks[i]);
+		if (ret)
+			return ret;
+	}
+
+	clk_alpha_pll_configure(&perfcl_pll, regmap, &hfpll_config);
+	clk_alpha_pll_configure(&pwrcl_pll, regmap, &hfpll_config);
+	clk_alpha_pll_configure(&perfcl_alt_pll, regmap, &altpll_config);
+	clk_alpha_pll_configure(&pwrcl_alt_pll, regmap, &altpll_config);
+
+	return ret;
+}
+
+static int qcom_cpu_clk_msm8996_driver_probe(struct platform_device *pdev)
+{
+	int ret;
+	void __iomem *base;
+	struct resource *res;
+	struct regmap *regmap;
+	struct clk_hw_onecell_data *data;
+	struct device *dev = &pdev->dev;
+
+	data = devm_kzalloc(dev, sizeof(*data) + 2 * sizeof(struct clk_hw *),
+			    GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(base))
+		return PTR_ERR(base);
+
+	regmap = devm_regmap_init_mmio(dev, base, &cpu_msm8996_regmap_config);
+	if (IS_ERR(regmap))
+		return PTR_ERR(regmap);
+
+	ret = qcom_cpu_clk_msm8996_register_clks(dev, regmap);
+	if (ret)
+		return ret;
+
+	data->hws[0] = &pwrcl_pmux.clkr.hw;
+	data->hws[1] = &perfcl_pmux.clkr.hw;
+	data->num = 2;
+
+	return devm_of_clk_add_hw_provider(dev, of_clk_hw_onecell_get, data);
+}
+
+static const struct of_device_id qcom_cpu_clk_msm8996_match_table[] = {
+	{ .compatible = "qcom,msm8996-apcc" },
+	{}
+};
+
+static struct platform_driver qcom_cpu_clk_msm8996_driver = {
+	.probe = qcom_cpu_clk_msm8996_driver_probe,
+	.driver = {
+		.name = "qcom-msm8996-apcc",
+		.of_match_table = qcom_cpu_clk_msm8996_match_table,
+	},
+};
+module_platform_driver(qcom_cpu_clk_msm8996_driver);
+
+MODULE_ALIAS("platform:msm8996-apcc");
+MODULE_DESCRIPTION("QCOM MSM8996 CPU Clock Driver");
+MODULE_LICENSE("GPL v2");
-- 
1.9.1

[PATCH v6 04/14] clk: qcom: Add DT bindings for CPU clock driver for msm8996

[Ilia Lin]

Each of the CPU clusters (Power and Perf) on msm8996 are
clocked via 2 PLLs, a primary and alternate. There are also
2 Mux'es, a primary and secondary all connected together
as shown below

                             +-------+
              XO             |       |
          +------------------>0      |
                             |       |
                   PLL/2     | SMUX  +----+
                     +------->1      |    |
                     |       |       |    |
                     |       +-------+    |    +-------+
                     |                    +---->0      |
                     |                         |       |
+---------------+    |             +----------->1      | CPU clk
|Primary PLL    +----+ PLL_EARLY   |           |       +------>
|               +------+-----------+    +------>2 PMUX |
+---------------+      |                |      |       |
                       |   +------+     |   +-->3      |
                       +--^+  ACD +-----+   |  +-------+
+---------------+          +------+         |
|Alt PLL        |                           |
|               +---------------------------+
+---------------+         PLL_EARLY

The primary PLL is what drives the CPU clk, except for times
when we are reprogramming the PLL itself (for rate changes) when
we temporarily switch to an alternate PLL. A subsequent patch adds
support to switch between primary and alternate PLL during rate
changes.

The primary PLL operates on a single VCO range, between 600MHz
and 3GHz. However the CPUs do support OPPs with frequencies
between 300MHz and 600MHz. In order to support running the CPUs
at those frequencies we end up having to lock the PLL at twice
the rate and drive the CPU clk via the PLL/2 output and SMUX.

Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/clock/qcom,kryocc.txt | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/clock/qcom,kryocc.txt

diff --git a/Documentation/devicetree/bindings/clock/qcom,kryocc.txt b/Documentation/devicetree/bindings/clock/qcom,kryocc.txt
new file mode 100644
index 0000000..8458783
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/qcom,kryocc.txt
@@ -0,0 +1,17 @@
+Qualcomm CPUSS clock controller for Kryo CPUs
+----------------------------------------------------
+
+Required properties :
+- compatible : shall contain only one of the following:
+
+			"qcom,msm8996-apcc"
+
+- reg : shall contain base register location and length
+- #clock-cells : shall contain 1
+
+Example:
+	kryocc: clock-controller@6400000 {
+		compatible = "qcom,msm8996-apcc";
+		reg = <0x6400000 0x90000>;
+		#clock-cells = <1>;
+	};
-- 
1.9.1

[PATCH v6 05/14] clk: qcom: cpu-8996: Add support to switch to alternate PLL

[Ilia Lin]

From: Rajendra Nayak <rnayak@codeaurora.org>

Each of the CPU clusters on msm8996 are powered via a primary
PLL and a secondary PLL. The primary PLL is what drives the
CPU clk, except for times when we are reprogramming the PLL
itself, when we temporarily switch to an alternate PLL.
Use clock rate change notifiers to support this.

Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
---
 drivers/clk/qcom/clk-cpu-8996.c | 33 +++++++++++++++++++++++++++++++++
 1 file changed, 33 insertions(+)

diff --git a/drivers/clk/qcom/clk-cpu-8996.c b/drivers/clk/qcom/clk-cpu-8996.c
index beb97eb..390b369 100644
--- a/drivers/clk/qcom/clk-cpu-8996.c
+++ b/drivers/clk/qcom/clk-cpu-8996.c
@@ -61,6 +61,7 @@
  * detect voltage droops. We do not add support for ACD as yet.
  */
 
+#include <linux/clk.h>
 #include <linux/module.h>
 #include <linux/platform_device.h>
 #include <linux/regmap.h>
@@ -187,10 +188,14 @@ struct clk_cpu_8996_mux {
 	u32	reg;
 	u8	shift;
 	u8	width;
+	struct notifier_block nb;
 	struct clk_hw	*pll;
 	struct clk_regmap clkr;
 };
 
+#define to_clk_cpu_8996_mux_nb(_nb) \
+	container_of(_nb, struct clk_cpu_8996_mux, nb)
+
 static inline
 struct clk_cpu_8996_mux *to_clk_cpu_8996_mux_hw(struct clk_hw *hw)
 {
@@ -236,6 +241,26 @@ static int clk_cpu_8996_mux_set_parent(struct clk_hw *hw, u8 index)
 	return 0;
 }
 
+int cpu_clk_notifier_cb(struct notifier_block *nb, unsigned long event,
+			void *data)
+{
+	int ret;
+	struct clk_cpu_8996_mux *cpuclk = to_clk_cpu_8996_mux_nb(nb);
+
+	switch (event) {
+	case PRE_RATE_CHANGE:
+		ret = clk_cpu_8996_mux_set_parent(&cpuclk->clkr.hw, ALT_INDEX);
+		break;
+	case POST_RATE_CHANGE:
+		ret = clk_cpu_8996_mux_set_parent(&cpuclk->clkr.hw, PLL_INDEX);
+		break;
+	default:
+		ret = 0;
+		break;
+	}
+
+	return notifier_from_errno(ret);
+};
 const struct clk_ops clk_cpu_8996_mux_ops = {
 	.set_parent = clk_cpu_8996_mux_set_parent,
 	.get_parent = clk_cpu_8996_mux_get_parent,
@@ -279,6 +304,7 @@ static int clk_cpu_8996_mux_set_parent(struct clk_hw *hw, u8 index)
 	.shift = 0,
 	.width = 2,
 	.pll = &pwrcl_pll.clkr.hw,
+	.nb.notifier_call = cpu_clk_notifier_cb,
 	.clkr.hw.init = &(struct clk_init_data) {
 		.name = "pwrcl_pmux",
 		.parent_names = (const char *[]){
@@ -298,6 +324,7 @@ static int clk_cpu_8996_mux_set_parent(struct clk_hw *hw, u8 index)
 	.shift = 0,
 	.width = 2,
 	.pll = &perfcl_pll.clkr.hw,
+	.nb.notifier_call = cpu_clk_notifier_cb,
 	.clkr.hw.init = &(struct clk_init_data) {
 		.name = "perfcl_pmux",
 		.parent_names = (const char *[]){
@@ -356,6 +383,12 @@ struct clk_regmap *clks[] = {
 	clk_alpha_pll_configure(&perfcl_alt_pll, regmap, &altpll_config);
 	clk_alpha_pll_configure(&pwrcl_alt_pll, regmap, &altpll_config);
 
+	ret = clk_notifier_register(pwrcl_pmux.clkr.hw.clk, &pwrcl_pmux.nb);
+	if (ret)
+		return ret;
+
+	ret = clk_notifier_register(perfcl_pmux.clkr.hw.clk, &perfcl_pmux.nb);
+
 	return ret;
 }
 
-- 
1.9.1

[PATCH v6 06/14] clk: qcom: cpu-8996: Add support to switch below 600Mhz

[Ilia Lin]

From: Rajendra Nayak <rnayak@codeaurora.org>

The CPU clock controller's primary PLL operates on a single VCO range,
between 600MHz and 3GHz. However the CPUs do support OPPs with
frequencies between 300MHz and 600MHz. In order to support running the
CPUs at those frequencies we end up having to lock the PLL at twice the
rate and drive the CPU clk via the PLL/2 output and SMUX.

So for frequencies above 600MHz we follow the following path
 Primary PLL --> PLL_EARLY --> PMUX(1) --> CPU clk
and for frequencies between 300MHz and 600MHz we follow
 Primary PLL --> PLL/2 --> SMUX(1) --> PMUX(0) --> CPU clk

Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>

Conflicts:
	drivers/clk/qcom/clk-cpu-8996.c
---
 drivers/clk/qcom/clk-cpu-8996.c | 25 ++++++++++++++++++++++---
 1 file changed, 22 insertions(+), 3 deletions(-)

diff --git a/drivers/clk/qcom/clk-cpu-8996.c b/drivers/clk/qcom/clk-cpu-8996.c
index 390b369..3ea0446 100644
--- a/drivers/clk/qcom/clk-cpu-8996.c
+++ b/drivers/clk/qcom/clk-cpu-8996.c
@@ -77,6 +77,8 @@ enum _pmux_input {
 	NUM_OF_PMUX_INPUTS
 };
 
+#define DIV_2_THRESHOLD		600000000
+
 static const u8 prim_pll_regs[PLL_OFF_MAX_REGS] = {
        [PLL_OFF_L_VAL] = 0x04,
        [PLL_OFF_ALPHA_VAL] = 0x08,
@@ -104,10 +106,11 @@ enum _pmux_input {
 
 static const struct alpha_pll_config hfpll_config = {
 	.l = 60,
-	.config_ctl_val = 0x200d4828,
+	.config_ctl_val = 0x200d4aa8,
 	.config_ctl_hi_val = 0x006,
 	.pre_div_mask = BIT(12),
 	.post_div_mask = 0x3 << 8,
+	.post_div_val = 0x1 << 8,
 	.main_output_mask = BIT(0),
 	.early_output_mask = BIT(3),
 };
@@ -149,7 +152,7 @@ enum _pmux_input {
 	.vco_mask = 0x3 << 20,
 	.config_ctl_val = 0x4001051b,
 	.post_div_mask = 0x3 << 8,
-	.post_div_val = 0x1,
+	.post_div_val = 0x1 << 8,
 	.main_output_mask = BIT(0),
 	.early_output_mask = BIT(3),
 };
@@ -190,6 +193,7 @@ struct clk_cpu_8996_mux {
 	u8	width;
 	struct notifier_block nb;
 	struct clk_hw	*pll;
+	struct clk_hw	*pll_div_2;
 	struct clk_regmap clkr;
 };
 
@@ -235,6 +239,13 @@ static int clk_cpu_8996_mux_set_parent(struct clk_hw *hw, u8 index)
 	struct clk_cpu_8996_mux *cpuclk = to_clk_cpu_8996_mux_hw(hw);
 	struct clk_hw *parent = cpuclk->pll;
 
+	if (cpuclk->pll_div_2 && req->rate < DIV_2_THRESHOLD) {
+		if (req->rate < (DIV_2_THRESHOLD / 2))
+			return -EINVAL;
+
+		parent = cpuclk->pll_div_2;
+	}
+
 	req->best_parent_rate = clk_hw_round_rate(parent, req->rate);
 	req->best_parent_hw = parent;
 
@@ -246,13 +257,19 @@ int cpu_clk_notifier_cb(struct notifier_block *nb, unsigned long event,
 {
 	int ret;
 	struct clk_cpu_8996_mux *cpuclk = to_clk_cpu_8996_mux_nb(nb);
+	struct clk_notifier_data *cnd = data;
 
 	switch (event) {
 	case PRE_RATE_CHANGE:
 		ret = clk_cpu_8996_mux_set_parent(&cpuclk->clkr.hw, ALT_INDEX);
 		break;
 	case POST_RATE_CHANGE:
-		ret = clk_cpu_8996_mux_set_parent(&cpuclk->clkr.hw, PLL_INDEX);
+		if (cnd->new_rate < DIV_2_THRESHOLD)
+			ret = clk_cpu_8996_mux_set_parent(&cpuclk->clkr.hw,
+							  DIV_2_INDEX);
+		else
+			ret = clk_cpu_8996_mux_set_parent(&cpuclk->clkr.hw,
+							  PLL_INDEX);
 		break;
 	default:
 		ret = 0;
@@ -304,6 +321,7 @@ int cpu_clk_notifier_cb(struct notifier_block *nb, unsigned long event,
 	.shift = 0,
 	.width = 2,
 	.pll = &pwrcl_pll.clkr.hw,
+	.pll_div_2 = &pwrcl_smux.clkr.hw,
 	.nb.notifier_call = cpu_clk_notifier_cb,
 	.clkr.hw.init = &(struct clk_init_data) {
 		.name = "pwrcl_pmux",
@@ -324,6 +342,7 @@ int cpu_clk_notifier_cb(struct notifier_block *nb, unsigned long event,
 	.shift = 0,
 	.width = 2,
 	.pll = &perfcl_pll.clkr.hw,
+	.pll_div_2 = &perfcl_smux.clkr.hw,
 	.nb.notifier_call = cpu_clk_notifier_cb,
 	.clkr.hw.init = &(struct clk_init_data) {
 		.name = "perfcl_pmux",
-- 
1.9.1

[PATCH v6 07/14] clk: qcom: Add ACD path to CPU clock driver for msm8996

[Ilia Lin]

The PMUX for each duplex allows for selection of ACD clock source.
The DVM (Dynamic Variation Monitor) will flag an error
when a voltage droop event is detected. This flagged error
enables ACD to provide a div-by-2 clock, sourced from the primary PLL.
The duplex will be provided the divided clock
until a pre-programmed delay has expired.

This change configures ACD during the probe and switches
the PMUXes to the ACD clock source.

Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
---
 drivers/clk/qcom/clk-cpu-8996.c | 75 +++++++++++++++++++++++++++++++++++------
 1 file changed, 65 insertions(+), 10 deletions(-)

diff --git a/drivers/clk/qcom/clk-cpu-8996.c b/drivers/clk/qcom/clk-cpu-8996.c
index 3ea0446..396285c 100644
--- a/drivers/clk/qcom/clk-cpu-8996.c
+++ b/drivers/clk/qcom/clk-cpu-8996.c
@@ -62,9 +62,11 @@
  */
 
 #include <linux/clk.h>
+#include <linux/clk-provider.h>
 #include <linux/module.h>
 #include <linux/platform_device.h>
 #include <linux/regmap.h>
+#include <soc/qcom/kryo-l2-accessors.h>
 
 #include "clk-alpha-pll.h"
 #include "clk-regmap.h"
@@ -78,6 +80,11 @@ enum _pmux_input {
 };
 
 #define DIV_2_THRESHOLD		600000000
+#define PWRCL_REG_OFFSET 0x0
+#define PERFCL_REG_OFFSET 0x80000
+#define MUX_OFFSET	0x40
+#define ALT_PLL_OFFSET	0x100
+#define SSSCTL_OFFSET 0x160
 
 static const u8 prim_pll_regs[PLL_OFF_MAX_REGS] = {
        [PLL_OFF_L_VAL] = 0x04,
@@ -116,7 +123,7 @@ enum _pmux_input {
 };
 
 static struct clk_alpha_pll perfcl_pll = {
-	.offset = 0x80000,
+	.offset = PERFCL_REG_OFFSET,
 	.regs = prim_pll_regs,
 	.flags = SUPPORTS_DYNAMIC_UPDATE | SUPPORTS_FSM_MODE,
 	.clkr.hw.init = &(struct clk_init_data){
@@ -128,7 +135,7 @@ enum _pmux_input {
 };
 
 static struct clk_alpha_pll pwrcl_pll = {
-	.offset = 0x0,
+	.offset = PWRCL_REG_OFFSET,
 	.regs = prim_pll_regs,
 	.flags = SUPPORTS_DYNAMIC_UPDATE | SUPPORTS_FSM_MODE,
 	.clkr.hw.init = &(struct clk_init_data){
@@ -158,7 +165,7 @@ enum _pmux_input {
 };
 
 static struct clk_alpha_pll perfcl_alt_pll = {
-	.offset = 0x80100,
+	.offset = PERFCL_REG_OFFSET + ALT_PLL_OFFSET,
 	.regs = alt_pll_regs,
 	.vco_table = alt_pll_vco_modes,
 	.num_vco = ARRAY_SIZE(alt_pll_vco_modes),
@@ -172,7 +179,7 @@ enum _pmux_input {
 };
 
 static struct clk_alpha_pll pwrcl_alt_pll = {
-	.offset = 0x100,
+	.offset = PWRCL_REG_OFFSET + ALT_PLL_OFFSET,
 	.regs = alt_pll_regs,
 	.vco_table = alt_pll_vco_modes,
 	.num_vco = ARRAY_SIZE(alt_pll_vco_modes),
@@ -185,6 +192,9 @@ enum _pmux_input {
 	},
 };
 
+void __iomem *base;
+static void qcom_cpu_clk_msm8996_acd_init(void __iomem *base);
+
 /* Mux'es */
 
 struct clk_cpu_8996_mux {
@@ -262,6 +272,7 @@ int cpu_clk_notifier_cb(struct notifier_block *nb, unsigned long event,
 	switch (event) {
 	case PRE_RATE_CHANGE:
 		ret = clk_cpu_8996_mux_set_parent(&cpuclk->clkr.hw, ALT_INDEX);
+		qcom_cpu_clk_msm8996_acd_init(base);
 		break;
 	case POST_RATE_CHANGE:
 		if (cnd->new_rate < DIV_2_THRESHOLD)
@@ -269,7 +280,7 @@ int cpu_clk_notifier_cb(struct notifier_block *nb, unsigned long event,
 							  DIV_2_INDEX);
 		else
 			ret = clk_cpu_8996_mux_set_parent(&cpuclk->clkr.hw,
-							  PLL_INDEX);
+							  ACD_INDEX);
 		break;
 	default:
 		ret = 0;
@@ -285,7 +296,7 @@ int cpu_clk_notifier_cb(struct notifier_block *nb, unsigned long event,
 };
 
 static struct clk_cpu_8996_mux pwrcl_smux = {
-	.reg = 0x40,
+	.reg = PWRCL_REG_OFFSET + MUX_OFFSET,
 	.shift = 2,
 	.width = 2,
 	.clkr.hw.init = &(struct clk_init_data) {
@@ -301,7 +312,7 @@ int cpu_clk_notifier_cb(struct notifier_block *nb, unsigned long event,
 };
 
 static struct clk_cpu_8996_mux perfcl_smux = {
-	.reg = 0x80040,
+	.reg = PERFCL_REG_OFFSET + MUX_OFFSET,
 	.shift = 2,
 	.width = 2,
 	.clkr.hw.init = &(struct clk_init_data) {
@@ -317,7 +328,7 @@ int cpu_clk_notifier_cb(struct notifier_block *nb, unsigned long event,
 };
 
 static struct clk_cpu_8996_mux pwrcl_pmux = {
-	.reg = 0x40,
+	.reg = PWRCL_REG_OFFSET + MUX_OFFSET,
 	.shift = 0,
 	.width = 2,
 	.pll = &pwrcl_pll.clkr.hw,
@@ -338,7 +349,7 @@ int cpu_clk_notifier_cb(struct notifier_block *nb, unsigned long event,
 };
 
 static struct clk_cpu_8996_mux perfcl_pmux = {
-	.reg = 0x80040,
+	.reg = PERFCL_REG_OFFSET + MUX_OFFSET,
 	.shift = 0,
 	.width = 2,
 	.pll = &perfcl_pll.clkr.hw,
@@ -402,6 +413,10 @@ struct clk_regmap *clks[] = {
 	clk_alpha_pll_configure(&perfcl_alt_pll, regmap, &altpll_config);
 	clk_alpha_pll_configure(&pwrcl_alt_pll, regmap, &altpll_config);
 
+	/* Enable alt PLLs */
+	clk_prepare_enable(pwrcl_alt_pll.clkr.hw.clk);
+	clk_prepare_enable(perfcl_alt_pll.clkr.hw.clk);
+
 	ret = clk_notifier_register(pwrcl_pmux.clkr.hw.clk, &pwrcl_pmux.nb);
 	if (ret)
 		return ret;
@@ -411,10 +426,48 @@ struct clk_regmap *clks[] = {
 	return ret;
 }
 
+#define CPU_AFINITY_MASK 0xFFF
+#define PWRCL_CPU_REG_MASK 0x3
+#define PERFCL_CPU_REG_MASK 0x103
+
+#define L2ACDCR_REG 0x580ULL
+#define L2ACDTD_REG 0x581ULL
+#define L2ACDDVMRC_REG 0x584ULL
+#define L2ACDSSCR_REG 0x589ULL
+
+static DEFINE_SPINLOCK(acd_lock);
+
+static void qcom_cpu_clk_msm8996_acd_init(void __iomem *base)
+{
+	u64 hwid;
+	unsigned long flags;
+
+	spin_lock_irqsave(&acd_lock, flags);
+
+	hwid = read_cpuid_mpidr() & CPU_AFINITY_MASK;
+
+	kryo_l2_set_indirect_reg(L2ACDTD_REG, 0x00006A11);
+	kryo_l2_set_indirect_reg(L2ACDDVMRC_REG, 0x000E0F0F);
+	kryo_l2_set_indirect_reg(L2ACDSSCR_REG, 0x00000601);
+
+	if (PWRCL_CPU_REG_MASK == (hwid | PWRCL_CPU_REG_MASK)) {
+		writel(0xF, base + PWRCL_REG_OFFSET + SSSCTL_OFFSET);
+		wmb();
+		kryo_l2_set_indirect_reg(L2ACDCR_REG, 0x002C5FFD);
+	}
+
+	if (PERFCL_CPU_REG_MASK == (hwid | PERFCL_CPU_REG_MASK)) {
+		kryo_l2_set_indirect_reg(L2ACDCR_REG, 0x002C5FFD);
+		writel(0xF, base + PERFCL_REG_OFFSET + SSSCTL_OFFSET);
+		wmb();
+	}
+
+	spin_unlock_irqrestore(&acd_lock, flags);
+}
+
 static int qcom_cpu_clk_msm8996_driver_probe(struct platform_device *pdev)
 {
 	int ret;
-	void __iomem *base;
 	struct resource *res;
 	struct regmap *regmap;
 	struct clk_hw_onecell_data *data;
@@ -438,6 +491,8 @@ static int qcom_cpu_clk_msm8996_driver_probe(struct platform_device *pdev)
 	if (ret)
 		return ret;
 
+	qcom_cpu_clk_msm8996_acd_init(base);
+
 	data->hws[0] = &pwrcl_pmux.clkr.hw;
 	data->hws[1] = &perfcl_pmux.clkr.hw;
 	data->num = 2;
-- 
1.9.1

[PATCH v6 08/14] dt: qcom: Add opp and thermal to the msm8996

[Ilia Lin]

Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
---
 arch/arm64/boot/dts/qcom/msm8996.dtsi | 269 ++++++++++++++++++++++++++++++++--
 1 file changed, 260 insertions(+), 9 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index 37b7152c..e6cf290 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -14,6 +14,7 @@
 #include <dt-bindings/clock/qcom,gcc-msm8996.h>
 #include <dt-bindings/clock/qcom,mmcc-msm8996.h>
 #include <dt-bindings/clock/qcom,rpmcc.h>
+#include <dt-bindings/thermal/thermal.h>
 
 / {
 	model = "Qualcomm Technologies, Inc. MSM8996";
@@ -97,6 +98,9 @@
 			compatible = "qcom,kryo";
 			reg = <0x0 0x0>;
 			enable-method = "psci";
+			clocks = <&kryocc 0>;
+			operating-points-v2 = <&cluster0_opp>;
+			#cooling-cells = <2>;
 			next-level-cache = <&L2_0>;
 			L2_0: l2-cache {
 			      compatible = "cache";
@@ -109,6 +113,9 @@
 			compatible = "qcom,kryo";
 			reg = <0x0 0x1>;
 			enable-method = "psci";
+			clocks = <&kryocc 0>;
+			operating-points-v2 = <&cluster0_opp>;
+			#cooling-cells = <2>;
 			next-level-cache = <&L2_0>;
 		};
 
@@ -117,6 +124,9 @@
 			compatible = "qcom,kryo";
 			reg = <0x0 0x100>;
 			enable-method = "psci";
+			clocks = <&kryocc 1>;
+			operating-points-v2 = <&cluster1_opp>;
+			#cooling-cells = <2>;
 			next-level-cache = <&L2_1>;
 			L2_1: l2-cache {
 			      compatible = "cache";
@@ -129,6 +139,9 @@
 			compatible = "qcom,kryo";
 			reg = <0x0 0x101>;
 			enable-method = "psci";
+			clocks = <&kryocc 1>;
+			operating-points-v2 = <&cluster1_opp>;
+			#cooling-cells = <2>;
 			next-level-cache = <&L2_1>;
 		};
 
@@ -155,6 +168,182 @@
 		};
 	};
 
+	cluster0_opp: opp_table0 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-307200000 {
+			opp-hz = /bits/ 64 <307200000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-422400000 {
+			opp-hz = /bits/ 64 <422400000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-480000000 {
+			opp-hz = /bits/ 64 <480000000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-556800000 {
+			opp-hz = /bits/ 64 <556800000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-652800000 {
+			opp-hz = /bits/ 64 <652800000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-729600000 {
+			opp-hz = /bits/ 64 <729600000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-844800000 {
+			opp-hz = /bits/ 64 <844800000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-960000000 {
+			opp-hz = /bits/ 64 <960000000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1036800000 {
+			opp-hz = /bits/ 64 <1036800000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1113600000 {
+			opp-hz = /bits/ 64 <1113600000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1190400000 {
+			opp-hz = /bits/ 64 <1190400000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1228800000 {
+			opp-hz = /bits/ 64 <1228800000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1324800000 {
+			opp-hz = /bits/ 64 <1324800000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1401600000 {
+			opp-hz = /bits/ 64 <1401600000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1478400000 {
+			opp-hz = /bits/ 64 <1478400000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1593600000 {
+			opp-hz = /bits/ 64 <1593600000>;
+			clock-latency-ns = <200000>;
+		};
+	};
+
+	cluster1_opp: opp_table1 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-307200000 {
+			opp-hz = /bits/ 64 <307200000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-403200000 {
+			opp-hz = /bits/ 64 <403200000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-480000000 {
+			opp-hz = /bits/ 64 <480000000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-556800000 {
+			opp-hz = /bits/ 64 <556800000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-652800000 {
+			opp-hz = /bits/ 64 <652800000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-729600000 {
+			opp-hz = /bits/ 64 <729600000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-806400000 {
+			opp-hz = /bits/ 64 <806400000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-883200000 {
+			opp-hz = /bits/ 64 <883200000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-940800000 {
+			opp-hz = /bits/ 64 <940800000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1036800000 {
+			opp-hz = /bits/ 64 <1036800000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1113600000 {
+			opp-hz = /bits/ 64 <1113600000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1190400000 {
+			opp-hz = /bits/ 64 <1190400000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1248000000 {
+			opp-hz = /bits/ 64 <1248000000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1324800000 {
+			opp-hz = /bits/ 64 <1324800000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1401600000 {
+			opp-hz = /bits/ 64 <1401600000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1478400000 {
+			opp-hz = /bits/ 64 <1478400000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1555200000 {
+			opp-hz = /bits/ 64 <1555200000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1632000000 {
+			opp-hz = /bits/ 64 <1632000000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1708800000 {
+			opp-hz = /bits/ 64 <1708800000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1785600000 {
+			opp-hz = /bits/ 64 <1785600000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1824000000 {
+			opp-hz = /bits/ 64 <1824000000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1920000000 {
+			opp-hz = /bits/ 64 <1920000000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1996800000 {
+			opp-hz = /bits/ 64 <1996800000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-2073600000 {
+			opp-hz = /bits/ 64 <2073600000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-2150400000 {
+			opp-hz = /bits/ 64 <2150400000>;
+			clock-latency-ns = <200000>;
+		};
+	};
+
 	thermal-zones {
 		cpu-thermal0 {
 			polling-delay-passive = <250>;
@@ -163,18 +352,34 @@
 			thermal-sensors = <&tsens0 3>;
 
 			trips {
-				cpu_alert0: trip0 {
+				cpu_alert0: cpu_alert0 {
 					temperature = <75000>;
 					hysteresis = <2000>;
+					type = "active";
+				};
+				cpu_warn0: cpu_warn0 {
+					temperature = <90000>;
+					hysteresis = <2000>;
 					type = "passive";
 				};
 
-				cpu_crit0: trip1 {
+				cpu_crit0: cpu_crit0 {
 					temperature = <110000>;
 					hysteresis = <2000>;
 					type = "critical";
 				};
 			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu_alert0>;
+					cooling-device = <&CPU0 THERMAL_NO_LIMIT 7>;
+				};
+				map1 {
+					trip = <&cpu_warn0>;
+					cooling-device = <&CPU0 8 THERMAL_NO_LIMIT>;
+				};
+			};
 		};
 
 		cpu-thermal1 {
@@ -184,18 +389,34 @@
 			thermal-sensors = <&tsens0 5>;
 
 			trips {
-				cpu_alert1: trip0 {
+				cpu_alert1: cpu_alert1 {
 					temperature = <75000>;
 					hysteresis = <2000>;
+					type = "active";
+				};
+				cpu_warn1: cpu_warn1 {
+					temperature = <90000>;
+					hysteresis = <2000>;
 					type = "passive";
 				};
 
-				cpu_crit1: trip1 {
+				cpu_crit1: cpu_crit1 {
 					temperature = <110000>;
 					hysteresis = <2000>;
 					type = "critical";
 				};
 			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu_alert1>;
+					cooling-device = <&CPU0 THERMAL_NO_LIMIT 7>;
+				};
+				map1 {
+					trip = <&cpu_warn1>;
+					cooling-device = <&CPU0 8 THERMAL_NO_LIMIT>;
+				};
+			};
 		};
 
 		cpu-thermal2 {
@@ -205,18 +426,33 @@
 			thermal-sensors = <&tsens0 8>;
 
 			trips {
-				cpu_alert2: trip0 {
+				cpu_alert2: cpu_alert2 {
 					temperature = <75000>;
 					hysteresis = <2000>;
+					type = "active";
+				};
+				cpu_warn2: cpu_warn2 {
+					temperature = <90000>;
+					hysteresis = <2000>;
 					type = "passive";
 				};
 
-				cpu_crit2: trip1 {
+				cpu_crit2: cpu_crit2 {
 					temperature = <110000>;
 					hysteresis = <2000>;
 					type = "critical";
 				};
 			};
+			cooling-maps {
+				map0 {
+					trip = <&cpu_alert2>;
+					cooling-device = <&CPU2 THERMAL_NO_LIMIT 7>;
+				};
+				map1 {
+					trip = <&cpu_warn2>;
+					cooling-device = <&CPU2 8 THERMAL_NO_LIMIT>;
+				};
+			};
 		};
 
 		cpu-thermal3 {
@@ -226,9 +462,14 @@
 			thermal-sensors = <&tsens0 10>;
 
 			trips {
-				cpu_alert3: trip0 {
+				cpu_alert3: cpu_alert3 {
 					temperature = <75000>;
 					hysteresis = <2000>;
+					type = "active";
+				};
+				cpu_warn3: cpu_warn3 {
+					temperature = <90000>;
+					hysteresis = <2000>;
 					type = "passive";
 				};
 
@@ -238,6 +479,16 @@
 					type = "critical";
 				};
 			};
+			cooling-maps {
+				map0 {
+					trip = <&cpu_alert3>;
+					cooling-device = <&CPU2 THERMAL_NO_LIMIT 7>;
+				};
+				map1 {
+					trip = <&cpu_warn3>;
+					cooling-device = <&CPU2 8 THERMAL_NO_LIMIT>;
+				};
+			};
 		};
 	};
 
@@ -414,7 +665,7 @@
 		};
 
 		kryocc: clock-controller@6400000 {
-			compatible = "qcom,apcc-msm8996";
+			compatible = "qcom,msm8996-apcc";
 			reg = <0x6400000 0x90000>;
 			#clock-cells = <1>;
 		};
@@ -1001,7 +1252,7 @@
 
 				pinctrl-names = "default", "sleep";
 				pinctrl-0 = <&pcie2_clkreq_default &pcie2_perst_default &pcie2_wake_default>;
-				pinctrl-1 = <&pcie2_clkreq_sleep &pcie2_perst_default &pcie2_wake_sleep >;
+				pinctrl-1 = <&pcie2_clkreq_sleep &pcie2_perst_default &pcie2_wake_sleep>;
 
 				vdda-supply = <&pm8994_l28>;
 
-- 
1.9.1

Re: [PATCH v6 08/14] dt: qcom: Add opp and thermal to the msm8996

[Viresh Kumar]

On 14-05-18, 16:11, Ilia Lin wrote:
> Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
> ---
>  arch/arm64/boot/dts/qcom/msm8996.dtsi | 269 ++++++++++++++++++++++++++++++++--
>  1 file changed, 260 insertions(+), 9 deletions(-)

Acked-by: Viresh Kumar <viresh.kumar@linaro.org>

-- 
viresh

[PATCH v6 09/14] regulator: qcom_spmi: Add support for SAW

[Ilia Lin]

Add support for SAW controlled regulators.
The regulators defined as SAW controlled in the device tree
will be controlled through special CPU registers instead of direct
SPMI accesses.
This is required especially for CPU supply regulators to synchronize
with clock scaling and for Automatic Voltage Switching.

Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
---
 drivers/regulator/qcom_spmi-regulator.c | 133 +++++++++++++++++++++++++++++++-
 1 file changed, 130 insertions(+), 3 deletions(-)

diff --git a/drivers/regulator/qcom_spmi-regulator.c b/drivers/regulator/qcom_spmi-regulator.c
index 63c7a0c..9817f1a 100644
--- a/drivers/regulator/qcom_spmi-regulator.c
+++ b/drivers/regulator/qcom_spmi-regulator.c
@@ -25,6 +25,8 @@
 #include <linux/regulator/driver.h>
 #include <linux/regmap.h>
 #include <linux/list.h>
+#include <linux/mfd/syscon.h>
+#include <linux/io.h>
 
 /* Pin control enable input pins. */
 #define SPMI_REGULATOR_PIN_CTRL_ENABLE_NONE		0x00
@@ -181,6 +183,23 @@ enum spmi_boost_byp_registers {
 	SPMI_BOOST_BYP_REG_CURRENT_LIMIT	= 0x4b,
 };
 
+enum spmi_saw3_registers {
+	SAW3_SECURE				= 0x00,
+	SAW3_ID					= 0x04,
+	SAW3_SPM_STS				= 0x0C,
+	SAW3_AVS_STS				= 0x10,
+	SAW3_PMIC_STS				= 0x14,
+	SAW3_RST				= 0x18,
+	SAW3_VCTL				= 0x1C,
+	SAW3_AVS_CTL				= 0x20,
+	SAW3_AVS_LIMIT				= 0x24,
+	SAW3_AVS_DLY				= 0x28,
+	SAW3_AVS_HYSTERESIS			= 0x2C,
+	SAW3_SPM_STS2				= 0x38,
+	SAW3_SPM_PMIC_DATA_3			= 0x4C,
+	SAW3_VERSION				= 0xFD0,
+};
+
 /* Used for indexing into ctrl_reg.  These are offets from 0x40 */
 enum spmi_common_control_register_index {
 	SPMI_COMMON_IDX_VOLTAGE_RANGE		= 0,
@@ -1035,6 +1054,89 @@ static irqreturn_t spmi_regulator_vs_ocp_isr(int irq, void *data)
 	return IRQ_HANDLED;
 }
 
+#define SAW3_VCTL_DATA_MASK	0xFF
+#define SAW3_VCTL_CLEAR_MASK	0x700FF
+#define SAW3_AVS_CTL_EN_MASK	0x1
+#define SAW3_AVS_CTL_TGGL_MASK	0x8000000
+#define SAW3_AVS_CTL_CLEAR_MASK	0x7efc00
+
+static struct regmap *saw_regmap = NULL;
+
+static void spmi_saw_set_vdd(void *data)
+{
+	u32 vctl, data3, avs_ctl, pmic_sts;
+	bool avs_enabled = false;
+	unsigned long timeout;
+	u8 voltage_sel = *(u8 *)data;
+
+	regmap_read(saw_regmap, SAW3_AVS_CTL, &avs_ctl);
+	regmap_read(saw_regmap, SAW3_VCTL, &vctl);
+	regmap_read(saw_regmap, SAW3_SPM_PMIC_DATA_3, &data3);
+
+	/* select the band */
+	vctl &= ~SAW3_VCTL_CLEAR_MASK;
+	vctl |= (u32)voltage_sel;
+
+	data3 &= ~SAW3_VCTL_CLEAR_MASK;
+	data3 |= (u32)voltage_sel;
+
+	/* If AVS is enabled, switch it off during the voltage change */
+	avs_enabled = SAW3_AVS_CTL_EN_MASK & avs_ctl;
+	if (avs_enabled) {
+		avs_ctl &= ~SAW3_AVS_CTL_TGGL_MASK;
+		regmap_write(saw_regmap, SAW3_AVS_CTL, avs_ctl);
+	}
+
+	regmap_write(saw_regmap, SAW3_RST, 1);
+	regmap_write(saw_regmap, SAW3_VCTL, vctl);
+	regmap_write(saw_regmap, SAW3_SPM_PMIC_DATA_3, data3);
+
+	timeout = jiffies + usecs_to_jiffies(100);
+	do {
+		regmap_read(saw_regmap, SAW3_PMIC_STS, &pmic_sts);
+		pmic_sts &= SAW3_VCTL_DATA_MASK;
+		if (pmic_sts == (u32)voltage_sel)
+			break;
+
+		cpu_relax();
+
+	} while (time_before(jiffies, timeout));
+
+	/* After successful voltage change, switch the AVS back on */
+	if (avs_enabled) {
+		pmic_sts &= 0x3f;
+		avs_ctl &= ~SAW3_AVS_CTL_CLEAR_MASK;
+		avs_ctl |= ((pmic_sts - 4) << 10);
+		avs_ctl |= (pmic_sts << 17);
+		avs_ctl |= SAW3_AVS_CTL_TGGL_MASK;
+		regmap_write(saw_regmap, SAW3_AVS_CTL, avs_ctl);
+	}
+}
+
+static int
+spmi_regulator_saw_set_voltage(struct regulator_dev *rdev, unsigned selector)
+{
+	struct spmi_regulator *vreg = rdev_get_drvdata(rdev);
+	int ret;
+	u8 range_sel, voltage_sel;
+
+	ret = spmi_sw_selector_to_hw(vreg, selector, &range_sel, &voltage_sel);
+	if (ret)
+		return ret;
+
+	if (0 != range_sel) {
+		dev_dbg(&rdev->dev, "range_sel = %02X voltage_sel = %02X", \
+			range_sel, voltage_sel);
+		return -EINVAL;
+	}
+
+	/* Always do the SAW register writes on the first CPU */
+	return smp_call_function_single(0, spmi_saw_set_vdd, \
+					&voltage_sel, true);
+}
+
+static struct regulator_ops spmi_saw_ops = {};
+
 static struct regulator_ops spmi_smps_ops = {
 	.enable			= regulator_enable_regmap,
 	.disable		= regulator_disable_regmap,
@@ -1250,6 +1352,7 @@ static int spmi_regulator_match(struct spmi_regulator *vreg, u16 force_type)
 	}
 	dig_major_rev	= version[SPMI_COMMON_REG_DIG_MAJOR_REV
 					- SPMI_COMMON_REG_DIG_MAJOR_REV];
+
 	if (!force_type) {
 		type		= version[SPMI_COMMON_REG_TYPE -
 					  SPMI_COMMON_REG_DIG_MAJOR_REV];
@@ -1648,7 +1751,9 @@ static int qcom_spmi_regulator_probe(struct platform_device *pdev)
 	struct regmap *regmap;
 	const char *name;
 	struct device *dev = &pdev->dev;
-	int ret;
+	struct device_node *node = pdev->dev.of_node;
+	struct device_node *syscon;
+	int ret, lenp;
 	struct list_head *vreg_list;
 
 	vreg_list = devm_kzalloc(dev, sizeof(*vreg_list), GFP_KERNEL);
@@ -1665,7 +1770,22 @@ static int qcom_spmi_regulator_probe(struct platform_device *pdev)
 	if (!match)
 		return -ENODEV;
 
+	if (of_find_property(node, "qcom,saw-reg", &lenp)) {
+		syscon = of_parse_phandle(node, "qcom,saw-reg", 0);
+		saw_regmap = syscon_node_to_regmap(syscon);
+		of_node_put(syscon);
+		if (IS_ERR(regmap))
+			dev_err(dev, "ERROR reading SAW regmap\n");
+	}
+
 	for (reg = match->data; reg->name; reg++) {
+
+		if (saw_regmap && \
+		    of_find_property(of_find_node_by_name(node, reg->name), \
+				     "qcom,saw-slave", &lenp)) {
+			continue;
+		}
+
 		vreg = devm_kzalloc(dev, sizeof(*vreg), GFP_KERNEL);
 		if (!vreg)
 			return -ENOMEM;
@@ -1673,7 +1793,6 @@ static int qcom_spmi_regulator_probe(struct platform_device *pdev)
 		vreg->dev = dev;
 		vreg->base = reg->base;
 		vreg->regmap = regmap;
-
 		if (reg->ocp) {
 			vreg->ocp_irq = platform_get_irq_byname(pdev, reg->ocp);
 			if (vreg->ocp_irq < 0) {
@@ -1681,7 +1800,6 @@ static int qcom_spmi_regulator_probe(struct platform_device *pdev)
 				goto err;
 			}
 		}
-
 		vreg->desc.id = -1;
 		vreg->desc.owner = THIS_MODULE;
 		vreg->desc.type = REGULATOR_VOLTAGE;
@@ -1698,6 +1816,15 @@ static int qcom_spmi_regulator_probe(struct platform_device *pdev)
 		if (ret)
 			continue;
 
+		if (saw_regmap && \
+		    of_find_property(of_find_node_by_name(node, reg->name), \
+				     "qcom,saw-leader", &lenp)) {
+			spmi_saw_ops = *(vreg->desc.ops);
+			spmi_saw_ops.set_voltage_sel = \
+				spmi_regulator_saw_set_voltage;
+			vreg->desc.ops = &spmi_saw_ops;
+		}
+
 		config.dev = dev;
 		config.driver_data = vreg;
 		config.regmap = regmap;
-- 
1.9.1

[PATCH v6 10/14] dt-bindings: qcom_spmi: Add support for SAW documentation

[Ilia Lin]

Add support for SAW controlled regulators.
The regulators defined as SAW controlled in the device tree
will be controlled through special CPU registers instead of direct
SPMI accesses.
This is required especially for CPU supply regulators to synchronize
with clock scaling and for Automatic Voltage Switching.
Document it.

Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
---
 .../bindings/regulator/qcom,spmi-regulator.txt     | 45 ++++++++++++++++++++++
 1 file changed, 45 insertions(+)

diff --git a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
index 57d2c65..406f2e5 100644
--- a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
@@ -110,6 +110,11 @@ Qualcomm SPMI Regulators
 	Definition: Reference to regulator supplying the input pin, as
 		    described in the data sheet.
 
+- qcom,saw-reg:
+	Usage: optional
+	Value type: <phandle>
+	Description: Reference to syscon node defining the SAW registers.
+
 
 The regulator node houses sub-nodes for each regulator within the device. Each
 sub-node is identified using the node's name, with valid values listed for each
@@ -201,6 +206,17 @@ see regulator.txt - with additional custom properties described below:
 			2 = 0.55 uA
 			3 = 0.75 uA
 
+- qcom,saw-slave:
+	Usage: optional
+	Value type: <boo>
+	Description: SAW controlled gang slave. Will not be configured.
+
+- qcom,saw-leader:
+	Usage: optional
+	Value type: <boo>
+	Description: SAW controlled gang leader. Will be configured as
+		     SAW regulator.
+
 Example:
 
 	regulators {
@@ -221,3 +237,32 @@ Example:
 
 		....
 	};
+
+Example 2:
+
+	saw3: syscon@9A10000 {
+		compatible = "syscon";
+		reg = <0x9A10000 0x1000>;
+	};
+
+	...
+
+	spm-regulators {
+		compatible = "qcom,pm8994-regulators";
+		qcom,saw-reg = <&saw3>;
+		s8 {
+			qcom,saw-slave;
+		};
+		s9 {
+			qcom,saw-slave;
+		};
+		s10 {
+			qcom,saw-slave;
+		};
+		pm8994_s11_saw: s11 {
+			qcom,saw-leader;
+			regulator-always-on;
+			regulator-min-microvolt = <900000>;
+			regulator-max-microvolt = <1140000>;
+		};
+	};
-- 
1.9.1

[PATCH v6 11/14] dt: qcom: Add SAW regulator for 8x96 CPUs

[Ilia Lin]

1. Add syscon node for the SAW CPU registers
2. Add SAW regulators gang definition for s8-s11
3. Add voltages to the OPP tables
4. Add the s11 SAW regulator as CPU regulator

Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
---
 arch/arm64/boot/dts/qcom/msm8996.dtsi | 75 +++++++++++++++++++++++++++++++++++
 1 file changed, 75 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index e6cf290..d7adef9 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -15,6 +15,7 @@
 #include <dt-bindings/clock/qcom,mmcc-msm8996.h>
 #include <dt-bindings/clock/qcom,rpmcc.h>
 #include <dt-bindings/thermal/thermal.h>
+#include <dt-bindings/spmi/spmi.h>
 
 / {
 	model = "Qualcomm Technologies, Inc. MSM8996";
@@ -99,6 +100,7 @@
 			reg = <0x0 0x0>;
 			enable-method = "psci";
 			clocks = <&kryocc 0>;
+			cpu-supply = <&pm8994_s11_saw>;
 			operating-points-v2 = <&cluster0_opp>;
 			#cooling-cells = <2>;
 			next-level-cache = <&L2_0>;
@@ -114,6 +116,7 @@
 			reg = <0x0 0x1>;
 			enable-method = "psci";
 			clocks = <&kryocc 0>;
+			cpu-supply = <&pm8994_s11_saw>;
 			operating-points-v2 = <&cluster0_opp>;
 			#cooling-cells = <2>;
 			next-level-cache = <&L2_0>;
@@ -125,6 +128,7 @@
 			reg = <0x0 0x100>;
 			enable-method = "psci";
 			clocks = <&kryocc 1>;
+			cpu-supply = <&pm8994_s11_saw>;
 			operating-points-v2 = <&cluster1_opp>;
 			#cooling-cells = <2>;
 			next-level-cache = <&L2_1>;
@@ -140,6 +144,7 @@
 			reg = <0x0 0x101>;
 			enable-method = "psci";
 			clocks = <&kryocc 1>;
+			cpu-supply = <&pm8994_s11_saw>;
 			operating-points-v2 = <&cluster1_opp>;
 			#cooling-cells = <2>;
 			next-level-cache = <&L2_1>;
@@ -174,66 +179,82 @@
 
 		opp-307200000 {
 			opp-hz = /bits/ 64 <307200000>;
+			opp-microvolt = <905000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-422400000 {
 			opp-hz = /bits/ 64 <422400000>;
+			opp-microvolt = <905000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-480000000 {
 			opp-hz = /bits/ 64 <480000000>;
+			opp-microvolt = <905000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-556800000 {
 			opp-hz = /bits/ 64 <556800000>;
+			opp-microvolt = <905000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-652800000 {
 			opp-hz = /bits/ 64 <652800000>;
+			opp-microvolt = <905000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-729600000 {
 			opp-hz = /bits/ 64 <729600000>;
+			opp-microvolt = <905000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-844800000 {
 			opp-hz = /bits/ 64 <844800000>;
+			opp-microvolt = <905000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-960000000 {
 			opp-hz = /bits/ 64 <960000000>;
+			opp-microvolt = <905000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1036800000 {
 			opp-hz = /bits/ 64 <1036800000>;
+			opp-microvolt = <905000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1113600000 {
 			opp-hz = /bits/ 64 <1113600000>;
+			opp-microvolt = <905000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1190400000 {
 			opp-hz = /bits/ 64 <1190400000>;
+			opp-microvolt = <905000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1228800000 {
 			opp-hz = /bits/ 64 <1228800000>;
+			opp-microvolt = <905000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1324800000 {
 			opp-hz = /bits/ 64 <1324800000>;
+			opp-microvolt = <1140000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1401600000 {
 			opp-hz = /bits/ 64 <1401600000>;
+			opp-microvolt = <1140000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1478400000 {
 			opp-hz = /bits/ 64 <1478400000>;
+			opp-microvolt = <1140000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1593600000 {
 			opp-hz = /bits/ 64 <1593600000>;
+			opp-microvolt = <1140000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 	};
@@ -244,102 +265,127 @@
 
 		opp-307200000 {
 			opp-hz = /bits/ 64 <307200000>;
+			opp-microvolt = <905000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-403200000 {
 			opp-hz = /bits/ 64 <403200000>;
+			opp-microvolt = <905000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-480000000 {
 			opp-hz = /bits/ 64 <480000000>;
+			opp-microvolt = <905000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-556800000 {
 			opp-hz = /bits/ 64 <556800000>;
+			opp-microvolt = <905000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-652800000 {
 			opp-hz = /bits/ 64 <652800000>;
+			opp-microvolt = <905000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-729600000 {
 			opp-hz = /bits/ 64 <729600000>;
+			opp-microvolt = <905000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-806400000 {
 			opp-hz = /bits/ 64 <806400000>;
+			opp-microvolt = <905000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-883200000 {
 			opp-hz = /bits/ 64 <883200000>;
+			opp-microvolt = <905000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-940800000 {
 			opp-hz = /bits/ 64 <940800000>;
+			opp-microvolt = <905000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1036800000 {
 			opp-hz = /bits/ 64 <1036800000>;
+			opp-microvolt = <905000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1113600000 {
 			opp-hz = /bits/ 64 <1113600000>;
+			opp-microvolt = <905000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1190400000 {
 			opp-hz = /bits/ 64 <1190400000>;
+			opp-microvolt = <905000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1248000000 {
 			opp-hz = /bits/ 64 <1248000000>;
+			opp-microvolt = <905000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1324800000 {
 			opp-hz = /bits/ 64 <1324800000>;
+			opp-microvolt = <1140000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1401600000 {
 			opp-hz = /bits/ 64 <1401600000>;
+			opp-microvolt = <1140000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1478400000 {
 			opp-hz = /bits/ 64 <1478400000>;
+			opp-microvolt = <1140000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1555200000 {
 			opp-hz = /bits/ 64 <1555200000>;
+			opp-microvolt = <1140000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1632000000 {
 			opp-hz = /bits/ 64 <1632000000>;
+			opp-microvolt = <1140000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1708800000 {
 			opp-hz = /bits/ 64 <1708800000>;
+			opp-microvolt = <1140000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1785600000 {
 			opp-hz = /bits/ 64 <1785600000>;
+			opp-microvolt = <1140000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1824000000 {
 			opp-hz = /bits/ 64 <1824000000>;
+			opp-microvolt = <1140000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1920000000 {
 			opp-hz = /bits/ 64 <1920000000>;
+			opp-microvolt = <1140000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1996800000 {
 			opp-hz = /bits/ 64 <1996800000>;
+			opp-microvolt = <1140000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-2073600000 {
 			opp-hz = /bits/ 64 <2073600000>;
+			opp-microvolt = <1140000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 		opp-2150400000 {
 			opp-hz = /bits/ 64 <2150400000>;
+			opp-microvolt = <1140000 905000 1140000>;
 			clock-latency-ns = <200000>;
 		};
 	};
@@ -656,6 +702,10 @@
 			#mbox-cells = <1>;
 		};
 
+		saw3: syscon@9A10000 {
+			compatible = "syscon";
+			reg = <0x9A10000 0x1000>;
+		};
 		gcc: clock-controller@300000 {
 			compatible = "qcom,gcc-msm8996";
 			#clock-cells = <1>;
@@ -882,6 +932,31 @@
 			#size-cells = <0>;
 			interrupt-controller;
 			#interrupt-cells = <4>;
+			pmic@1 {
+				compatible = "qcom,pm8994", "qcom,spmi-pmic";
+				reg = <0x1 SPMI_USID>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				spm-regulators {
+					compatible = "qcom,pm8994-regulators";
+					qcom,saw-reg = <&saw3>;
+					s8 {
+						qcom,saw-slave;
+					};
+					s9 {
+						qcom,saw-slave;
+					};
+					s10 {
+						qcom,saw-slave;
+					};
+					pm8994_s11_saw: s11 {
+						qcom,saw-leader;
+						regulator-always-on;
+						regulator-min-microvolt = <905000>;
+						regulator-max-microvolt = <1140000>;
+					};
+				};
+			};
 		};
 
 		mmcc: clock-controller@8c0000 {
-- 
1.9.1

Re: [PATCH v6 11/14] dt: qcom: Add SAW regulator for 8x96 CPUs

[Viresh Kumar]

On 14-05-18, 16:11, Ilia Lin wrote:
> 1. Add syscon node for the SAW CPU registers
> 2. Add SAW regulators gang definition for s8-s11
> 3. Add voltages to the OPP tables
> 4. Add the s11 SAW regulator as CPU regulator
> 
> Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
> ---
>  arch/arm64/boot/dts/qcom/msm8996.dtsi | 75 +++++++++++++++++++++++++++++++++++
>  1 file changed, 75 insertions(+)

Acked-by: Viresh Kumar <viresh.kumar@linaro.org>

-- 
viresh

[PATCH v6 12/14] cpufreq: Add Kryo CPU scaling driver

[Ilia Lin]

In Certain QCOM SoCs like apq8096 and msm8996 that have KRYO processors,
the CPU ferequencies subset and voltage value of each OPP varies
based on the silicon variant in use. Qualcomm Process Voltage Scaling Tables
defines the voltage and frequency value based on the msm-id in SMEM
and speedbin blown in the efuse combination.
The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC
to provide the OPP framework with required information.
This is used to determine the voltage and frequency value for each OPP of
operating-points-v2 table when it is parsed by the OPP framework.

Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
---
 drivers/cpufreq/Kconfig.arm          |  11 +++
 drivers/cpufreq/Makefile             |   1 +
 drivers/cpufreq/cpufreq-dt-platdev.c |   3 +
 drivers/cpufreq/qcom-cpufreq-kryo.c  | 148 +++++++++++++++++++++++++++++++++++
 4 files changed, 163 insertions(+)
 create mode 100644 drivers/cpufreq/qcom-cpufreq-kryo.c

diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm
index de55c7d..5c16f05 100644
--- a/drivers/cpufreq/Kconfig.arm
+++ b/drivers/cpufreq/Kconfig.arm
@@ -124,6 +124,17 @@ config ARM_OMAP2PLUS_CPUFREQ
 	depends on ARCH_OMAP2PLUS
 	default ARCH_OMAP2PLUS
 
+config ARM_QCOM_CPUFREQ_KRYO
+	bool "Qualcomm Technologies, Inc. Kryo based CPUFreq"
+	depends on QCOM_QFPROM
+	depends on QCOM_SMEM
+	select PM_OPP
+	help
+	  This adds the CPUFreq driver for
+	  Qualcomm Technologies, Inc. Kryo SoC based boards.
+
+	  If in doubt, say N.
+
 config ARM_S3C_CPUFREQ
 	bool
 	help
diff --git a/drivers/cpufreq/Makefile b/drivers/cpufreq/Makefile
index 8d24ade..fb4a2ec 100644
--- a/drivers/cpufreq/Makefile
+++ b/drivers/cpufreq/Makefile
@@ -65,6 +65,7 @@ obj-$(CONFIG_MACH_MVEBU_V7)		+= mvebu-cpufreq.o
 obj-$(CONFIG_ARM_OMAP2PLUS_CPUFREQ)	+= omap-cpufreq.o
 obj-$(CONFIG_ARM_PXA2xx_CPUFREQ)	+= pxa2xx-cpufreq.o
 obj-$(CONFIG_PXA3xx)			+= pxa3xx-cpufreq.o
+obj-$(CONFIG_ARM_QCOM_CPUFREQ_KRYO)	+= qcom-cpufreq-kryo.o
 obj-$(CONFIG_ARM_S3C2410_CPUFREQ)	+= s3c2410-cpufreq.o
 obj-$(CONFIG_ARM_S3C2412_CPUFREQ)	+= s3c2412-cpufreq.o
 obj-$(CONFIG_ARM_S3C2416_CPUFREQ)	+= s3c2416-cpufreq.o
diff --git a/drivers/cpufreq/cpufreq-dt-platdev.c b/drivers/cpufreq/cpufreq-dt-platdev.c
index 3b585e4..77d6ab8 100644
--- a/drivers/cpufreq/cpufreq-dt-platdev.c
+++ b/drivers/cpufreq/cpufreq-dt-platdev.c
@@ -118,6 +118,9 @@
 
 	{ .compatible = "nvidia,tegra124", },
 
+	{ .compatible = "qcom,apq8096", },
+	{ .compatible = "qcom,msm8996", },
+
 	{ .compatible = "st,stih407", },
 	{ .compatible = "st,stih410", },
 
diff --git a/drivers/cpufreq/qcom-cpufreq-kryo.c b/drivers/cpufreq/qcom-cpufreq-kryo.c
new file mode 100644
index 0000000..04bd0fa
--- /dev/null
+++ b/drivers/cpufreq/qcom-cpufreq-kryo.c
@@ -0,0 +1,148 @@
+// SPDX-License-Identifier: GPL-2.0
+/* 
+ * Copyright (c) 2018, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/cpu.h>
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/nvmem-consumer.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pm_opp.h>
+#include <linux/slab.h>
+#include <linux/soc/qcom/smem.h>
+
+#define MSM_ID_SMEM	137
+#define SILVER_LEAD	0
+#define GOLD_LEAD	2
+
+enum _msm_id {
+	MSM8996V3 = 0xF6ul,
+	APQ8096V3 = 0x123ul,
+	MSM8996SG = 0x131ul,
+	APQ8096SG = 0x138ul,
+};
+
+enum _msm8996_version {
+	MSM8996_V3,
+	MSM8996_SG,
+	NUM_OF_MSM8996_VERSIONS,
+};
+
+static enum _msm8996_version __init qcom_cpufreq_kryo_get_msm_id(void)
+{
+	size_t len;
+	u32 *msm_id;
+	enum _msm8996_version version;
+
+	msm_id = qcom_smem_get(QCOM_SMEM_HOST_ANY, MSM_ID_SMEM, &len);
+	/* The first 4 bytes are format, next to them is the actual msm-id */
+	msm_id++;
+
+	switch ((enum _msm_id)*msm_id) {
+	case MSM8996V3:
+	case APQ8096V3:
+		version = MSM8996_V3;
+		break;
+	case MSM8996SG:
+	case APQ8096SG:
+		version = MSM8996_SG;
+		break;
+	default:
+		version = NUM_OF_MSM8996_VERSIONS;
+	}
+
+	return version;
+}
+
+static int __init qcom_cpufreq_kryo_driver_init(void)
+{
+	size_t len;
+	int ret;
+	u32 versions;
+	enum _msm8996_version msm8996_version;
+	u8 *speedbin;
+	struct device *cpu_dev;
+	struct device_node *np;
+	struct nvmem_cell *speedbin_nvmem;
+	struct opp_table *opp_temp = NULL;
+
+	cpu_dev = get_cpu_device(SILVER_LEAD);
+	if (IS_ERR_OR_NULL(cpu_dev))
+		return PTR_ERR(cpu_dev);
+
+	msm8996_version = qcom_cpufreq_kryo_get_msm_id();
+	if (NUM_OF_MSM8996_VERSIONS == msm8996_version) {
+		dev_err(cpu_dev, "Not Snapdragon 820/821!");
+		return -ENODEV;
+        }
+
+	np = dev_pm_opp_of_get_opp_desc_node(cpu_dev);
+	if (IS_ERR_OR_NULL(np))
+		return PTR_ERR(np);
+
+	if (!of_device_is_compatible(np, "operating-points-v2-kryo-cpu")) {
+		ret = -ENOENT;
+		goto free_np;
+	}
+
+	speedbin_nvmem = of_nvmem_cell_get(np, NULL);
+	if (IS_ERR(speedbin_nvmem)) {
+		ret = PTR_ERR(speedbin_nvmem);
+		dev_err(cpu_dev, "Could not get nvmem cell: %d\n", ret);
+		goto free_np;
+	}
+
+	speedbin = nvmem_cell_read(speedbin_nvmem, &len);
+
+	switch (msm8996_version) {
+	case MSM8996_V3:
+		versions = 1 << (unsigned int)(*speedbin);
+		break;
+	case MSM8996_SG:
+		versions = 1 << ((unsigned int)(*speedbin) + 4);
+		break;
+	default:
+		BUG();
+		break;
+	}
+
+	ret = PTR_ERR_OR_ZERO(opp_temp = \
+			      dev_pm_opp_set_supported_hw(cpu_dev,&versions,1));
+	if (0 > ret)
+		goto free_np;
+
+	dev_pm_opp_put_supported_hw(opp_temp);
+
+	cpu_dev = get_cpu_device(GOLD_LEAD);
+	ret = PTR_ERR_OR_ZERO(opp_temp = \
+			      dev_pm_opp_set_supported_hw(cpu_dev,&versions,1));
+	if (0 > ret)
+		goto free_np;
+
+	ret = PTR_ERR_OR_ZERO(platform_device_register_simple("cpufreq-dt", \
+							      -1, NULL, 0));
+
+	dev_pm_opp_put_supported_hw(opp_temp);
+
+free_np:
+	of_node_put(np);
+
+	return ret;
+}
+late_initcall(qcom_cpufreq_kryo_driver_init);
+
+MODULE_DESCRIPTION("Qualcomm Technologies, Inc. Kryo CPUfreq driver");
+MODULE_LICENSE("GPL v2");
-- 
1.9.1

Re: [PATCH v6 12/14] cpufreq: Add Kryo CPU scaling driver

[Viresh Kumar]

On 14-05-18, 16:11, Ilia Lin wrote:
> +static int __init qcom_cpufreq_kryo_driver_init(void)
> +{
> +	size_t len;
> +	int ret;
> +	u32 versions;
> +	enum _msm8996_version msm8996_version;
> +	u8 *speedbin;
> +	struct device *cpu_dev;
> +	struct device_node *np;
> +	struct nvmem_cell *speedbin_nvmem;
> +	struct opp_table *opp_temp = NULL;
> +
> +	cpu_dev = get_cpu_device(SILVER_LEAD);
> +	if (IS_ERR_OR_NULL(cpu_dev))
> +		return PTR_ERR(cpu_dev);
> +
> +	msm8996_version = qcom_cpufreq_kryo_get_msm_id();
> +	if (NUM_OF_MSM8996_VERSIONS == msm8996_version) {
> +		dev_err(cpu_dev, "Not Snapdragon 820/821!");
> +		return -ENODEV;
> +        }
> +
> +	np = dev_pm_opp_of_get_opp_desc_node(cpu_dev);
> +	if (IS_ERR_OR_NULL(np))
> +		return PTR_ERR(np);
> +
> +	if (!of_device_is_compatible(np, "operating-points-v2-kryo-cpu")) {
> +		ret = -ENOENT;
> +		goto free_np;
> +	}
> +
> +	speedbin_nvmem = of_nvmem_cell_get(np, NULL);
> +	if (IS_ERR(speedbin_nvmem)) {
> +		ret = PTR_ERR(speedbin_nvmem);
> +		dev_err(cpu_dev, "Could not get nvmem cell: %d\n", ret);
> +		goto free_np;
> +	}
> +
> +	speedbin = nvmem_cell_read(speedbin_nvmem, &len);
> +
> +	switch (msm8996_version) {
> +	case MSM8996_V3:
> +		versions = 1 << (unsigned int)(*speedbin);
> +		break;
> +	case MSM8996_SG:
> +		versions = 1 << ((unsigned int)(*speedbin) + 4);
> +		break;
> +	default:
> +		BUG();
> +		break;
> +	}
> +
> +	ret = PTR_ERR_OR_ZERO(opp_temp = \

Why back slash here ?

> +			      dev_pm_opp_set_supported_hw(cpu_dev,&versions,1));
> +	if (0 > ret)
> +		goto free_np;
> +
> +	dev_pm_opp_put_supported_hw(opp_temp);
> +
> +	cpu_dev = get_cpu_device(GOLD_LEAD);
> +	ret = PTR_ERR_OR_ZERO(opp_temp = \

And here.

> +			      dev_pm_opp_set_supported_hw(cpu_dev,&versions,1));
> +	if (0 > ret)
> +		goto free_np;
> +
> +	ret = PTR_ERR_OR_ZERO(platform_device_register_simple("cpufreq-dt", \

and here.

> +							      -1, NULL, 0));
> +
> +	dev_pm_opp_put_supported_hw(opp_temp);

And this is wrong. You don't need to call this in success case here.
It may have worked for you as cpufreq-dt driver would have already
been initialized, but that's not the case always. For example try
inserting cpufreq-dt module after kernel boots and it will fail.

> +
> +free_np:
> +	of_node_put(np);
> +
> +	return ret;
> +}
> +late_initcall(qcom_cpufreq_kryo_driver_init);
> +
> +MODULE_DESCRIPTION("Qualcomm Technologies, Inc. Kryo CPUfreq driver");
> +MODULE_LICENSE("GPL v2");
> -- 
> 1.9.1

-- 
viresh

[PATCH v6 13/14] dt-bindings: cpufreq: Document operating-points-v2-kryo-cpu

[Ilia Lin]

In Certain Qualcomm Technologies, Inc. SoCs like apq8096 and msm8996
that have KRYO processors, the CPU ferequencies subset and voltage value
of each OPP varies based on the silicon variant in use.
Qualcomm Technologies, Inc. Process Voltage Scaling Tables
defines the voltage and frequency value based on the msm-id in SMEM
and speedbin blown in the efuse combination.
The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC
to provide the OPP framework with required information.
This is used to determine the voltage and frequency value for each OPP of
operating-points-v2 table when it is parsed by the OPP framework.

This change adds documentation.

Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
---
 .../devicetree/bindings/opp/kryo-cpufreq.txt       | 680 +++++++++++++++++++++
 1 file changed, 680 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/opp/kryo-cpufreq.txt

diff --git a/Documentation/devicetree/bindings/opp/kryo-cpufreq.txt b/Documentation/devicetree/bindings/opp/kryo-cpufreq.txt
new file mode 100644
index 0000000..c2127b9
--- /dev/null
+++ b/Documentation/devicetree/bindings/opp/kryo-cpufreq.txt
@@ -0,0 +1,680 @@
+Qualcomm Technologies, Inc. KRYO CPUFreq and OPP bindings
+===================================
+
+In Certain Qualcomm Technologies, Inc. SoCs like apq8096 and msm8996
+that have KRYO processors, the CPU ferequencies subset and voltage value
+of each OPP varies based on the silicon variant in use.
+Qualcomm Technologies, Inc. Process Voltage Scaling Tables
+defines the voltage and frequency value based on the msm-id in SMEM
+and speedbin blown in the efuse combination.
+The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC
+to provide the OPP framework with required information (existing HW bitmap).
+This is used to determine the voltage and frequency value for each OPP of
+operating-points-v2 table when it is parsed by the OPP framework.
+
+Required properties:
+--------------------
+In 'cpus' nodes:
+- operating-points-v2: Phandle to the operating-points-v2 table to use.
+
+In 'operating-points-v2' table:
+- compatible: Should be
+	- 'operating-points-v2-kryo-cpu' for apq8096 and msm8996.
+- nvmem-cells: A phandle pointing to a nvmem-cells node representing the
+		efuse registers that has information about the
+		speedbin that is used to select the right frequency/voltage
+		value pair.
+		Please refer the for nvmem-cells
+		bindings Documentation/devicetree/bindings/nvmem/nvmem.txt
+		and also examples below.
+
+In every OPP node:
+- opp-supported-hw: A single 32 bit bitmap value, representing compatible HW.
+		    Bitmap:
+			0:	MSM8996 V3, speedbin 0
+			1:	MSM8996 V3, speedbin 1
+			2:	MSM8996 V3, speedbin 2
+			3:	unused
+			4:	MSM8996 SG, speedbin 0
+			5:	MSM8996 SG, speedbin 1
+			6:	MSM8996 SG, speedbin 2
+			7-31:	unused
+
+Example 1:
+---------
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		CPU0: cpu@0 {
+			device_type = "cpu";
+			compatible = "qcom,kryo";
+			reg = <0x0 0x0>;
+			enable-method = "psci";
+			clocks = <&kryocc 0>;
+			cpu-supply = <&pm8994_s11_saw>;
+			operating-points-v2 = <&cluster0_opp>;
+			#cooling-cells = <2>;
+			next-level-cache = <&L2_0>;
+			L2_0: l2-cache {
+			      compatible = "cache";
+			      cache-level = <2>;
+			};
+		};
+
+		CPU1: cpu@1 {
+			device_type = "cpu";
+			compatible = "qcom,kryo";
+			reg = <0x0 0x1>;
+			enable-method = "psci";
+			clocks = <&kryocc 0>;
+			cpu-supply = <&pm8994_s11_saw>;
+			operating-points-v2 = <&cluster0_opp>;
+			#cooling-cells = <2>;
+			next-level-cache = <&L2_0>;
+		};
+
+		CPU2: cpu@100 {
+			device_type = "cpu";
+			compatible = "qcom,kryo";
+			reg = <0x0 0x100>;
+			enable-method = "psci";
+			clocks = <&kryocc 1>;
+			cpu-supply = <&pm8994_s11_saw>;
+			operating-points-v2 = <&cluster1_opp>;
+			#cooling-cells = <2>;
+			next-level-cache = <&L2_1>;
+			L2_1: l2-cache {
+			      compatible = "cache";
+			      cache-level = <2>;
+			};
+		};
+
+		CPU3: cpu@101 {
+			device_type = "cpu";
+			compatible = "qcom,kryo";
+			reg = <0x0 0x101>;
+			enable-method = "psci";
+			clocks = <&kryocc 1>;
+			cpu-supply = <&pm8994_s11_saw>;
+			operating-points-v2 = <&cluster1_opp>;
+			#cooling-cells = <2>;
+			next-level-cache = <&L2_1>;
+		};
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&CPU0>;
+				};
+
+				core1 {
+					cpu = <&CPU1>;
+				};
+			};
+
+			cluster1 {
+				core0 {
+					cpu = <&CPU2>;
+				};
+
+				core1 {
+					cpu = <&CPU3>;
+				};
+			};
+		};
+	};
+
+	cluster0_opp: opp_table0 {
+		compatible = "operating-points-v2-kryo-cpu";
+		nvmem-cells = <&speedbin_efuse>;
+		opp-shared;
+
+		opp-307200000 {
+			opp-hz = /bits/ 64 <307200000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x77>;
+			clock-latency-ns = <200000>;
+		};
+		opp-384000000 {
+			opp-hz = /bits/ 64 <384000000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-422400000 {
+			opp-hz = /bits/ 64 <422400000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-460800000 {
+			opp-hz = /bits/ 64 <460800000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-480000000 {
+			opp-hz = /bits/ 64 <480000000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-537600000 {
+			opp-hz = /bits/ 64 <537600000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-556800000 {
+			opp-hz = /bits/ 64 <556800000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-614400000 {
+			opp-hz = /bits/ 64 <614400000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-652800000 {
+			opp-hz = /bits/ 64 <652800000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-691200000 {
+			opp-hz = /bits/ 64 <691200000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-729600000 {
+			opp-hz = /bits/ 64 <729600000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-768000000 {
+			opp-hz = /bits/ 64 <768000000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-844800000 {
+			opp-hz = /bits/ 64 <844800000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x77>;
+			clock-latency-ns = <200000>;
+		};
+		opp-902400000 {
+			opp-hz = /bits/ 64 <902400000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-960000000 {
+			opp-hz = /bits/ 64 <960000000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-979200000 {
+			opp-hz = /bits/ 64 <979200000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1036800000 {
+			opp-hz = /bits/ 64 <1036800000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1056000000 {
+			opp-hz = /bits/ 64 <1056000000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1113600000 {
+			opp-hz = /bits/ 64 <1113600000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1132800000 {
+			opp-hz = /bits/ 64 <1132800000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1190400000 {
+			opp-hz = /bits/ 64 <1190400000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1209600000 {
+			opp-hz = /bits/ 64 <1209600000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1228800000 {
+			opp-hz = /bits/ 64 <1228800000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1286400000 {
+			opp-hz = /bits/ 64 <1286400000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1324800000 {
+			opp-hz = /bits/ 64 <1324800000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x5>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1363200000 {
+			opp-hz = /bits/ 64 <1363200000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x72>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1401600000 {
+			opp-hz = /bits/ 64 <1401600000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x5>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1440000000 {
+			opp-hz = /bits/ 64 <1440000000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1478400000 {
+			opp-hz = /bits/ 64 <1478400000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x1>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1497600000 {
+			opp-hz = /bits/ 64 <1497600000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x4>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1516800000 {
+			opp-hz = /bits/ 64 <1516800000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1593600000 {
+			opp-hz = /bits/ 64 <1593600000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x71>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1996800000 {
+			opp-hz = /bits/ 64 <1996800000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x20>;
+			clock-latency-ns = <200000>;
+		};
+		opp-2188800000 {
+			opp-hz = /bits/ 64 <2188800000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x10>;
+			clock-latency-ns = <200000>;
+		};
+	};
+
+	cluster1_opp: opp_table1 {
+		compatible = "operating-points-v2-kryo-cpu";
+		nvmem-cells = <&speedbin_efuse>;
+		opp-shared;
+
+		opp-307200000 {
+			opp-hz = /bits/ 64 <307200000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x77>;
+			clock-latency-ns = <200000>;
+		};
+		opp-384000000 {
+			opp-hz = /bits/ 64 <384000000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-403200000 {
+			opp-hz = /bits/ 64 <403200000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-460800000 {
+			opp-hz = /bits/ 64 <460800000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-480000000 {
+			opp-hz = /bits/ 64 <480000000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-537600000 {
+			opp-hz = /bits/ 64 <537600000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-556800000 {
+			opp-hz = /bits/ 64 <556800000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-614400000 {
+			opp-hz = /bits/ 64 <614400000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-652800000 {
+			opp-hz = /bits/ 64 <652800000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-691200000 {
+			opp-hz = /bits/ 64 <691200000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-729600000 {
+			opp-hz = /bits/ 64 <729600000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-748800000 {
+			opp-hz = /bits/ 64 <748800000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-806400000 {
+			opp-hz = /bits/ 64 <806400000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-825600000 {
+			opp-hz = /bits/ 64 <825600000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-883200000 {
+			opp-hz = /bits/ 64 <883200000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-902400000 {
+			opp-hz = /bits/ 64 <902400000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-940800000 {
+			opp-hz = /bits/ 64 <940800000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-979200000 {
+			opp-hz = /bits/ 64 <979200000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1036800000 {
+			opp-hz = /bits/ 64 <1036800000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1056000000 {
+			opp-hz = /bits/ 64 <1056000000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1113600000 {
+			opp-hz = /bits/ 64 <1113600000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1132800000 {
+			opp-hz = /bits/ 64 <1132800000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1190400000 {
+			opp-hz = /bits/ 64 <1190400000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1209600000 {
+			opp-hz = /bits/ 64 <1209600000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1248000000 {
+			opp-hz = /bits/ 64 <1248000000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1286400000 {
+			opp-hz = /bits/ 64 <1286400000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1324800000 {
+			opp-hz = /bits/ 64 <1324800000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1363200000 {
+			opp-hz = /bits/ 64 <1363200000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1401600000 {
+			opp-hz = /bits/ 64 <1401600000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1440000000 {
+			opp-hz = /bits/ 64 <1440000000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1478400000 {
+			opp-hz = /bits/ 64 <1478400000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1516800000 {
+			opp-hz = /bits/ 64 <1516800000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1555200000 {
+			opp-hz = /bits/ 64 <1555200000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1593600000 {
+			opp-hz = /bits/ 64 <1593600000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1632000000 {
+			opp-hz = /bits/ 64 <1632000000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1670400000 {
+			opp-hz = /bits/ 64 <1670400000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1708800000 {
+			opp-hz = /bits/ 64 <1708800000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1747200000 {
+			opp-hz = /bits/ 64 <1747200000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1785600000 {
+			opp-hz = /bits/ 64 <1785600000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1804800000 {
+			opp-hz = /bits/ 64 <1804800000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x6>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1824000000 {
+			opp-hz = /bits/ 64 <1824000000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x71>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1900800000 {
+			opp-hz = /bits/ 64 <1900800000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x74>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1920000000 {
+			opp-hz = /bits/ 64 <1920000000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x1>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1977600000 {
+			opp-hz = /bits/ 64 <1977600000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x30>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1996800000 {
+			opp-hz = /bits/ 64 <1996800000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x1>;
+			clock-latency-ns = <200000>;
+		};
+		opp-2054400000 {
+			opp-hz = /bits/ 64 <2054400000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x30>;
+			clock-latency-ns = <200000>;
+		};
+		opp-2073600000 {
+			opp-hz = /bits/ 64 <2073600000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x1>;
+			clock-latency-ns = <200000>;
+		};
+		opp-2150400000 {
+			opp-hz = /bits/ 64 <2150400000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x31>;
+			clock-latency-ns = <200000>;
+		};
+		opp-2246400000 {
+			opp-hz = /bits/ 64 <2246400000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x10>;
+			clock-latency-ns = <200000>;
+		};
+		opp-2342400000 {
+			opp-hz = /bits/ 64 <2342400000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x10>;
+			clock-latency-ns = <200000>;
+		};
+	};
+
+....
+
+reserved-memory {
+	#address-cells = <2>;
+	#size-cells = <2>;
+	ranges;
+....
+	smem_mem: smem-mem@86000000 {
+		reg = <0x0 0x86000000 0x0 0x200000>;
+		no-map;
+	};
+....
+};
+
+smem {
+	compatible = "qcom,smem";
+	memory-region = <&smem_mem>;
+	hwlocks = <&tcsr_mutex 3>;
+};
+
+soc {
+....
+	qfprom: qfprom@74000 {
+		compatible = "qcom,qfprom";
+		reg = <0x00074000 0x8ff>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		....
+		speedbin_efuse: speedbin@133 {
+			reg = <0x133 0x1>;
+			bits = <5 3>;
+		};
+	};
+};
-- 
1.9.1

Re: [PATCH v6 13/14] dt-bindings: cpufreq: Document operating-points-v2-kryo-cpu

[Viresh Kumar]

On 14-05-18, 16:11, Ilia Lin wrote:
> In Certain Qualcomm Technologies, Inc. SoCs like apq8096 and msm8996
> that have KRYO processors, the CPU ferequencies subset and voltage value
> of each OPP varies based on the silicon variant in use.
> Qualcomm Technologies, Inc. Process Voltage Scaling Tables
> defines the voltage and frequency value based on the msm-id in SMEM
> and speedbin blown in the efuse combination.
> The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC
> to provide the OPP framework with required information.
> This is used to determine the voltage and frequency value for each OPP of
> operating-points-v2 table when it is parsed by the OPP framework.
> 
> This change adds documentation.
> 
> Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
> ---
>  .../devicetree/bindings/opp/kryo-cpufreq.txt       | 680 +++++++++++++++++++++
>  1 file changed, 680 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/opp/kryo-cpufreq.txt

Acked-by: Viresh Kumar <viresh.kumar@linaro.org>

-- 
viresh

[PATCH v6 14/14] dt: qcom: Add qcom-cpufreq-kryo driver configuration

[Ilia Lin]

Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
---
 arch/arm64/boot/dts/qcom/apq8096-db820c.dts |   2 +-
 arch/arm64/boot/dts/qcom/msm8996.dtsi       | 310 +++++++++++++++++++++++++++-
 2 files changed, 309 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/apq8096-db820c.dts b/arch/arm64/boot/dts/qcom/apq8096-db820c.dts
index 230e9c8..da23bda 100644
--- a/arch/arm64/boot/dts/qcom/apq8096-db820c.dts
+++ b/arch/arm64/boot/dts/qcom/apq8096-db820c.dts
@@ -17,5 +17,5 @@
 
 / {
 	model = "Qualcomm Technologies, Inc. DB820c";
-	compatible = "arrow,apq8096-db820c", "qcom,apq8096-sbc";
+	compatible = "arrow,apq8096-db820c", "qcom,apq8096-sbc", "qcom,apq8096";
 };
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index d7adef9..fbf92f6 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -174,218 +174,519 @@
 	};
 
 	cluster0_opp: opp_table0 {
-		compatible = "operating-points-v2";
+		compatible = "operating-points-v2-kryo-cpu";
+		nvmem-cells = <&speedbin_efuse>;
 		opp-shared;
 
 		opp-307200000 {
 			opp-hz = /bits/ 64 <307200000>;
 			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x77>;
+			clock-latency-ns = <200000>;
+		};
+		opp-384000000 {
+			opp-hz = /bits/ 64 <384000000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
 		};
 		opp-422400000 {
 			opp-hz = /bits/ 64 <422400000>;
 			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-460800000 {
+			opp-hz = /bits/ 64 <460800000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
 		};
 		opp-480000000 {
 			opp-hz = /bits/ 64 <480000000>;
 			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-537600000 {
+			opp-hz = /bits/ 64 <537600000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
 		};
 		opp-556800000 {
 			opp-hz = /bits/ 64 <556800000>;
 			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-614400000 {
+			opp-hz = /bits/ 64 <614400000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
 		};
 		opp-652800000 {
 			opp-hz = /bits/ 64 <652800000>;
 			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-691200000 {
+			opp-hz = /bits/ 64 <691200000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
 		};
 		opp-729600000 {
 			opp-hz = /bits/ 64 <729600000>;
 			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-768000000 {
+			opp-hz = /bits/ 64 <768000000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
 		};
 		opp-844800000 {
 			opp-hz = /bits/ 64 <844800000>;
 			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x77>;
+			clock-latency-ns = <200000>;
+		};
+		opp-902400000 {
+			opp-hz = /bits/ 64 <902400000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
 		};
 		opp-960000000 {
 			opp-hz = /bits/ 64 <960000000>;
 			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-979200000 {
+			opp-hz = /bits/ 64 <979200000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1036800000 {
 			opp-hz = /bits/ 64 <1036800000>;
 			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1056000000 {
+			opp-hz = /bits/ 64 <1056000000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1113600000 {
 			opp-hz = /bits/ 64 <1113600000>;
 			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1132800000 {
+			opp-hz = /bits/ 64 <1132800000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1190400000 {
 			opp-hz = /bits/ 64 <1190400000>;
 			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1209600000 {
+			opp-hz = /bits/ 64 <1209600000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1228800000 {
 			opp-hz = /bits/ 64 <1228800000>;
 			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1286400000 {
+			opp-hz = /bits/ 64 <1286400000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1324800000 {
 			opp-hz = /bits/ 64 <1324800000>;
 			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x5>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1363200000 {
+			opp-hz = /bits/ 64 <1363200000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x72>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1401600000 {
 			opp-hz = /bits/ 64 <1401600000>;
 			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x5>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1440000000 {
+			opp-hz = /bits/ 64 <1440000000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1478400000 {
 			opp-hz = /bits/ 64 <1478400000>;
 			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x1>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1497600000 {
+			opp-hz = /bits/ 64 <1497600000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x4>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1516800000 {
+			opp-hz = /bits/ 64 <1516800000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1593600000 {
 			opp-hz = /bits/ 64 <1593600000>;
 			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x71>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1996800000 {
+			opp-hz = /bits/ 64 <1996800000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x20>;
+			clock-latency-ns = <200000>;
+		};
+		opp-2188800000 {
+			opp-hz = /bits/ 64 <2188800000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x10>;
 			clock-latency-ns = <200000>;
 		};
 	};
 
 	cluster1_opp: opp_table1 {
-		compatible = "operating-points-v2";
+		compatible = "operating-points-v2-kryo-cpu";
+		nvmem-cells = <&speedbin_efuse>;
 		opp-shared;
 
 		opp-307200000 {
 			opp-hz = /bits/ 64 <307200000>;
 			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x77>;
+			clock-latency-ns = <200000>;
+		};
+		opp-384000000 {
+			opp-hz = /bits/ 64 <384000000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
 		};
 		opp-403200000 {
 			opp-hz = /bits/ 64 <403200000>;
 			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-460800000 {
+			opp-hz = /bits/ 64 <460800000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
 		};
 		opp-480000000 {
 			opp-hz = /bits/ 64 <480000000>;
 			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-537600000 {
+			opp-hz = /bits/ 64 <537600000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
 		};
 		opp-556800000 {
 			opp-hz = /bits/ 64 <556800000>;
 			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-614400000 {
+			opp-hz = /bits/ 64 <614400000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
 		};
 		opp-652800000 {
 			opp-hz = /bits/ 64 <652800000>;
 			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-691200000 {
+			opp-hz = /bits/ 64 <691200000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
 		};
 		opp-729600000 {
 			opp-hz = /bits/ 64 <729600000>;
 			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-748800000 {
+			opp-hz = /bits/ 64 <748800000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
 		};
 		opp-806400000 {
 			opp-hz = /bits/ 64 <806400000>;
 			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-825600000 {
+			opp-hz = /bits/ 64 <825600000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
 		};
 		opp-883200000 {
 			opp-hz = /bits/ 64 <883200000>;
 			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-902400000 {
+			opp-hz = /bits/ 64 <902400000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
 		};
 		opp-940800000 {
 			opp-hz = /bits/ 64 <940800000>;
 			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-979200000 {
+			opp-hz = /bits/ 64 <979200000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1036800000 {
 			opp-hz = /bits/ 64 <1036800000>;
 			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1056000000 {
+			opp-hz = /bits/ 64 <1056000000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1113600000 {
 			opp-hz = /bits/ 64 <1113600000>;
 			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1132800000 {
+			opp-hz = /bits/ 64 <1132800000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1190400000 {
 			opp-hz = /bits/ 64 <1190400000>;
 			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1209600000 {
+			opp-hz = /bits/ 64 <1209600000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1248000000 {
 			opp-hz = /bits/ 64 <1248000000>;
 			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1286400000 {
+			opp-hz = /bits/ 64 <1286400000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1324800000 {
 			opp-hz = /bits/ 64 <1324800000>;
 			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1363200000 {
+			opp-hz = /bits/ 64 <1363200000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1401600000 {
 			opp-hz = /bits/ 64 <1401600000>;
 			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1440000000 {
+			opp-hz = /bits/ 64 <1440000000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1478400000 {
 			opp-hz = /bits/ 64 <1478400000>;
 			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1516800000 {
+			opp-hz = /bits/ 64 <1516800000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1555200000 {
 			opp-hz = /bits/ 64 <1555200000>;
 			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1593600000 {
+			opp-hz = /bits/ 64 <1593600000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1632000000 {
 			opp-hz = /bits/ 64 <1632000000>;
 			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1670400000 {
+			opp-hz = /bits/ 64 <1670400000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1708800000 {
 			opp-hz = /bits/ 64 <1708800000>;
 			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1747200000 {
+			opp-hz = /bits/ 64 <1747200000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1785600000 {
 			opp-hz = /bits/ 64 <1785600000>;
 			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1804800000 {
+			opp-hz = /bits/ 64 <1804800000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x6>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1824000000 {
 			opp-hz = /bits/ 64 <1824000000>;
 			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x71>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1900800000 {
+			opp-hz = /bits/ 64 <1900800000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x74>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1920000000 {
 			opp-hz = /bits/ 64 <1920000000>;
 			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x1>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1977600000 {
+			opp-hz = /bits/ 64 <1977600000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x30>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1996800000 {
 			opp-hz = /bits/ 64 <1996800000>;
 			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x1>;
+			clock-latency-ns = <200000>;
+		};
+		opp-2054400000 {
+			opp-hz = /bits/ 64 <2054400000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x30>;
 			clock-latency-ns = <200000>;
 		};
 		opp-2073600000 {
 			opp-hz = /bits/ 64 <2073600000>;
 			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x1>;
 			clock-latency-ns = <200000>;
 		};
 		opp-2150400000 {
 			opp-hz = /bits/ 64 <2150400000>;
 			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x31>;
+			clock-latency-ns = <200000>;
+		};
+		opp-2246400000 {
+			opp-hz = /bits/ 64 <2246400000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x10>;
+			clock-latency-ns = <200000>;
+		};
+		opp-2342400000 {
+			opp-hz = /bits/ 64 <2342400000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x10>;
 			clock-latency-ns = <200000>;
 		};
 	};
@@ -992,6 +1293,11 @@
 				reg = <0x24f 0x1>;
 				bits = <1 4>;
 			};
+
+			speedbin_efuse: speedbin@133 {
+				reg = <0x133 0x1>;
+				bits = <5 3>;
+			};
 		};
 
 		phy@34000 {
-- 
1.9.1

Re: [PATCH v6 14/14] dt: qcom: Add qcom-cpufreq-kryo driver configuration

[Viresh Kumar]

On 14-05-18, 16:12, Ilia Lin wrote:
> Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
> ---
>  arch/arm64/boot/dts/qcom/apq8096-db820c.dts |   2 +-
>  arch/arm64/boot/dts/qcom/msm8996.dtsi       | 310 +++++++++++++++++++++++++++-
>  2 files changed, 309 insertions(+), 3 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/qcom/apq8096-db820c.dts b/arch/arm64/boot/dts/qcom/apq8096-db820c.dts
> index 230e9c8..da23bda 100644
> --- a/arch/arm64/boot/dts/qcom/apq8096-db820c.dts
> +++ b/arch/arm64/boot/dts/qcom/apq8096-db820c.dts
> @@ -17,5 +17,5 @@
>  
>  / {
>  	model = "Qualcomm Technologies, Inc. DB820c";
> -	compatible = "arrow,apq8096-db820c", "qcom,apq8096-sbc";
> +	compatible = "arrow,apq8096-db820c", "qcom,apq8096-sbc", "qcom,apq8096";
>  };
> diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
> index d7adef9..fbf92f6 100644
> --- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
> +++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
> @@ -174,218 +174,519 @@
>  	};
>  
>  	cluster0_opp: opp_table0 {
> -		compatible = "operating-points-v2";
> +		compatible = "operating-points-v2-kryo-cpu";

I think you need to mention both the above compatible strings here
with the kyro one mentioned first.


-- 
viresh