From mboxrd@z Thu Jan 1 00:00:00 1970 From: Sricharan R Subject: [PATCH V7 02/12] ARM: dts: ipq4019: Add a few peripheral nodes Date: Fri, 18 May 2018 13:49:15 +0530 Message-ID: <1526631565-9972-3-git-send-email-sricharan@codeaurora.org> References: <1526631565-9972-1-git-send-email-sricharan@codeaurora.org> Return-path: In-Reply-To: <1526631565-9972-1-git-send-email-sricharan@codeaurora.org> Sender: linux-kernel-owner@vger.kernel.org To: robh+dt@kernel.org, robh@kernel.org, mark.rutland@arm.com, linux@armlinux.org.uk, andy.gross@linaro.org, david.brown@linaro.org, catalin.marinas@arm.com, will.deacon@arm.com, sboyd@codeaurora.org, bjorn.andersson@linaro.org, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-arm-msm@vger.kernel.org, linux-soc@vger.kernel.org, absahu@codeaurora.org, marc.zyngier@arm.com, richardcochran@gmail.com, sricharan@codeaurora.org List-Id: linux-arm-msm@vger.kernel.org Now with the driver updates for some peripherals being there, add i2c, spi, pcie, bam, qpic-nand, scm nodes to enhance the available peripheral support. Reviewed-by: Abhishek Sahu Signed-off-by: Sricharan R --- arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi | 2 +- arch/arm/boot/dts/qcom-ipq4019.dtsi | 156 ++++++++++++++++++++++++-- 2 files changed, 146 insertions(+), 12 deletions(-) diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi b/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi index ef8d8c8..418f9a0 100644 --- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi +++ b/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi @@ -69,7 +69,7 @@ status = "ok"; }; - spi_0: spi@78b5000 { + spi@78b5000 { pinctrl-0 = <&spi_0_pins>; pinctrl-names = "default"; status = "ok"; diff --git a/arch/arm/boot/dts/qcom-ipq4019.dtsi b/arch/arm/boot/dts/qcom-ipq4019.dtsi index ea9202a..1541e18 100644 --- a/arch/arm/boot/dts/qcom-ipq4019.dtsi +++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi @@ -24,8 +24,10 @@ interrupt-parent = <&intc>; aliases { - spi0 = &spi_0; - i2c0 = &i2c_0; + spi0 = &blsp1_spi1; + spi1 = &blsp1_spi2; + i2c0 = &blsp1_i2c3; + i2c1 = &blsp1_i2c4; }; cpus { @@ -104,6 +106,12 @@ }; }; + firmware { + scm { + compatible = "qcom,scm-ipq4019"; + }; + }; + timer { compatible = "arm,armv7-timer"; interrupts = <1 2 0xf08>, @@ -149,13 +157,13 @@ #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; - interrupts = <0 208 0>; + interrupts = ; }; blsp_dma: dma@7884000 { compatible = "qcom,bam-v1.7.0"; reg = <0x07884000 0x23000>; - interrupts = ; + interrupts = ; clocks = <&gcc GCC_BLSP1_AHB_CLK>; clock-names = "bam_clk"; #dma-cells = <1>; @@ -163,7 +171,7 @@ status = "disabled"; }; - spi_0: spi@78b5000 { + blsp1_spi1: spi@78b5000 { /* BLSP1 QUP1 */ compatible = "qcom,spi-qup-v2.2.1"; reg = <0x78b5000 0x600>; interrupts = ; @@ -172,10 +180,26 @@ clock-names = "core", "iface"; #address-cells = <1>; #size-cells = <0>; + dmas = <&blsp_dma 5>, <&blsp_dma 4>; + dma-names = "rx", "tx"; + status = "disabled"; + }; + + blsp1_spi2: spi@78b6000 { /* BLSP1 QUP2 */ + compatible = "qcom,spi-qup-v2.2.1"; + reg = <0x78b6000 0x600>; + interrupts = ; + clocks = <&gcc GCC_BLSP1_QUP2_SPI_APPS_CLK>, + <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + #address-cells = <1>; + #size-cells = <0>; + dmas = <&blsp_dma 7>, <&blsp_dma 6>; + dma-names = "rx", "tx"; status = "disabled"; }; - i2c_0: i2c@78b7000 { + blsp1_i2c3: i2c@78b7000 { /* BLSP1 QUP3 */ compatible = "qcom,i2c-qup-v2.2.1"; reg = <0x78b7000 0x600>; interrupts = ; @@ -184,14 +208,29 @@ clock-names = "iface", "core"; #address-cells = <1>; #size-cells = <0>; + dmas = <&blsp_dma 9>, <&blsp_dma 8>; + dma-names = "rx", "tx"; status = "disabled"; }; + blsp1_i2c4: i2c@78b8000 { /* BLSP1 QUP4 */ + compatible = "qcom,i2c-qup-v2.2.1"; + reg = <0x78b8000 0x600>; + interrupts = ; + clocks = <&gcc GCC_BLSP1_AHB_CLK>, + <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>; + clock-names = "iface", "core"; + #address-cells = <1>; + #size-cells = <0>; + dmas = <&blsp_dma 11>, <&blsp_dma 10>; + dma-names = "rx", "tx"; + status = "disabled"; + }; cryptobam: dma@8e04000 { compatible = "qcom,bam-v1.7.0"; reg = <0x08e04000 0x20000>; - interrupts = ; + interrupts = ; clocks = <&gcc GCC_CRYPTO_AHB_CLK>; clock-names = "bam_clk"; #dma-cells = <1>; @@ -259,7 +298,7 @@ blsp1_uart1: serial@78af000 { compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; reg = <0x78af000 0x200>; - interrupts = <0 107 0>; + interrupts = ; status = "disabled"; clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; @@ -271,7 +310,7 @@ serial@78b0000 { compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; reg = <0x78b0000 0x200>; - interrupts = <0 108 0>; + interrupts = ; status = "disabled"; clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; @@ -293,6 +332,101 @@ reg = <0x4ab000 0x4>; }; + pcie0: pci@40000000 { + compatible = "qcom,pcie-ipq4019", "snps,dw-pcie"; + reg = <0x40000000 0xf1d + 0x40000f20 0xa8 + 0x80000 0x2000 + 0x40100000 0x1000>; + reg-names = "dbi", "elbi", "parf", "config"; + device_type = "pci"; + linux,pci-domain = <0>; + bus-range = <0x00 0xff>; + num-lanes = <1>; + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x81000000 0 0x40200000 0x40200000 0 0x00100000 + 0x82000000 0 0x48000000 0x48000000 0 0x10000000>; + + interrupts = ; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0x7>; + interrupt-map = <0 0 0 1 &intc 0 142 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ + <0 0 0 2 &intc 0 143 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ + <0 0 0 3 &intc 0 144 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ + <0 0 0 4 &intc 0 145 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ + clocks = <&gcc GCC_PCIE_AHB_CLK>, + <&gcc GCC_PCIE_AXI_M_CLK>, + <&gcc GCC_PCIE_AXI_S_CLK>; + clock-names = "aux", + "master_bus", + "slave_bus"; + + resets = <&gcc PCIE_AXI_M_ARES>, + <&gcc PCIE_AXI_S_ARES>, + <&gcc PCIE_PIPE_ARES>, + <&gcc PCIE_AXI_M_VMIDMT_ARES>, + <&gcc PCIE_AXI_S_XPU_ARES>, + <&gcc PCIE_PARF_XPU_ARES>, + <&gcc PCIE_PHY_ARES>, + <&gcc PCIE_AXI_M_STICKY_ARES>, + <&gcc PCIE_PIPE_STICKY_ARES>, + <&gcc PCIE_PWR_ARES>, + <&gcc PCIE_AHB_ARES>, + <&gcc PCIE_PHY_AHB_ARES>; + reset-names = "axi_m", + "axi_s", + "pipe", + "axi_m_vmid", + "axi_s_xpu", + "parf", + "phy", + "axi_m_sticky", + "pipe_sticky", + "pwr", + "ahb", + "phy_ahb"; + + status = "disabled"; + }; + + qpic_bam: dma@7984000 { + compatible = "qcom,bam-v1.7.0"; + reg = <0x7984000 0x1a000>; + interrupts = ; + clocks = <&gcc GCC_QPIC_CLK>; + clock-names = "bam_clk"; + #dma-cells = <1>; + qcom,ee = <0>; + status = "disabled"; + }; + + nand: qpic-nand@79b0000 { + compatible = "qcom,ipq4019-nand"; + reg = <0x79b0000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&gcc GCC_QPIC_CLK>, + <&gcc GCC_QPIC_AHB_CLK>; + clock-names = "core", "aon"; + + dmas = <&qpic_bam 0>, + <&qpic_bam 1>, + <&qpic_bam 2>; + dma-names = "tx", "rx", "cmd"; + status = "disabled"; + + nand@0 { + reg = <0>; + + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + nand-bus-width = <8>; + }; + }; + wifi0: wifi@a000000 { compatible = "qcom,ipq4019-wifi"; reg = <0xa000000 0x200000>; @@ -326,7 +460,7 @@ , , , - ; + ; interrupt-names = "msi0", "msi1", "msi2", "msi3", "msi4", "msi5", "msi6", "msi7", "msi8", "msi9", "msi10", "msi11", @@ -368,7 +502,7 @@ , , , - ; + ; interrupt-names = "msi0", "msi1", "msi2", "msi3", "msi4", "msi5", "msi6", "msi7", "msi8", "msi9", "msi10", "msi11", -- QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation