linux-arm-msm.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Neeraj Upadhyay <neeraju@codeaurora.org>
To: bjorn.andersson@linaro.org, sboyd@codeaurora.org,
	linus.walleij@linaro.org, timur@codeaurora.org
Cc: linux-arm-msm@vger.kernel.org, linux-gpio@vger.kernel.org,
	linux-kernel@vger.kernel.org,
	Srinivas Ramana <sramana@codeaurora.org>,
	Neeraj Upadhyay <neeraju@codeaurora.org>
Subject: [PATCH v2] pinctrl: qcom: Add irq_enable callback for msm gpio
Date: Mon, 17 Jun 2019 15:04:50 +0530	[thread overview]
Message-ID: <1560764090-22740-1-git-send-email-neeraju@codeaurora.org> (raw)

From: Srinivas Ramana <sramana@codeaurora.org>

Introduce the irq_enable callback which will be same as irq_unmask
except that it will also clear the status bit before unmask.

This will help in clearing any erroneous interrupts that would
have got latched when the interrupt is not in use.

There may be devices like UART which can use the same gpio line
for data rx as well as a wakeup gpio when in suspend. The data that
was flowing on the line may latch the interrupt and when we enable
the interrupt before going to suspend, this would trigger the
unexpected interrupt. This change helps clearing the interrupt
so that these unexpected interrupts gets cleared.

Signed-off-by: Srinivas Ramana <sramana@codeaurora.org>
Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org>
---

Changes since v1:
- Extracted common code into __msm_gpio_irq_unmask().

 drivers/pinctrl/qcom/pinctrl-msm.c | 25 ++++++++++++++++++++++++-
 1 file changed, 24 insertions(+), 1 deletion(-)

diff --git a/drivers/pinctrl/qcom/pinctrl-msm.c b/drivers/pinctrl/qcom/pinctrl-msm.c
index 6e319bc..2a127f0 100644
--- a/drivers/pinctrl/qcom/pinctrl-msm.c
+++ b/drivers/pinctrl/qcom/pinctrl-msm.c
@@ -729,7 +729,7 @@ static void msm_gpio_irq_mask(struct irq_data *d)
 	raw_spin_unlock_irqrestore(&pctrl->lock, flags);
 }
 
-static void msm_gpio_irq_unmask(struct irq_data *d)
+static void __msm_gpio_irq_unmask(struct irq_data *d, bool status_clear)
 {
 	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
 	struct msm_pinctrl *pctrl = gpiochip_get_data(gc);
@@ -741,6 +741,17 @@ static void msm_gpio_irq_unmask(struct irq_data *d)
 
 	raw_spin_lock_irqsave(&pctrl->lock, flags);
 
+	if (status_clear) {
+		/*
+		 * clear the interrupt status bit before unmask to avoid
+		 * any erroneous interrupts that would have got latched
+		 * when the interrupt is not in use.
+		 */
+		val = msm_readl_intr_status(pctrl, g);
+		val &= ~BIT(g->intr_status_bit);
+		msm_writel_intr_status(val, pctrl, g);
+	}
+
 	val = msm_readl_intr_cfg(pctrl, g);
 	val |= BIT(g->intr_raw_status_bit);
 	val |= BIT(g->intr_enable_bit);
@@ -751,6 +762,17 @@ static void msm_gpio_irq_unmask(struct irq_data *d)
 	raw_spin_unlock_irqrestore(&pctrl->lock, flags);
 }
 
+static void msm_gpio_irq_enable(struct irq_data *d)
+{
+
+	__msm_gpio_irq_unmask(d, true);
+}
+
+static void msm_gpio_irq_unmask(struct irq_data *d)
+{
+	__msm_gpio_irq_unmask(d, false);
+}
+
 static void msm_gpio_irq_ack(struct irq_data *d)
 {
 	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
@@ -978,6 +1000,7 @@ static int msm_gpio_init(struct msm_pinctrl *pctrl)
 	chip->need_valid_mask = msm_gpio_needs_valid_mask(pctrl);
 
 	pctrl->irq_chip.name = "msmgpio";
+	pctrl->irq_chip.irq_enable = msm_gpio_irq_enable;
 	pctrl->irq_chip.irq_mask = msm_gpio_irq_mask;
 	pctrl->irq_chip.irq_unmask = msm_gpio_irq_unmask;
 	pctrl->irq_chip.irq_ack = msm_gpio_irq_ack;
-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a
member of the Code Aurora Forum, hosted by The Linux Foundation


             reply	other threads:[~2019-06-17  9:35 UTC|newest]

Thread overview: 4+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-06-17  9:34 Neeraj Upadhyay [this message]
2019-06-25  8:58 ` [PATCH v2] pinctrl: qcom: Add irq_enable callback for msm gpio Linus Walleij
2019-06-25 10:29   ` Neeraj Upadhyay
2019-06-25 12:18     ` Linus Walleij

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1560764090-22740-1-git-send-email-neeraju@codeaurora.org \
    --to=neeraju@codeaurora.org \
    --cc=bjorn.andersson@linaro.org \
    --cc=linus.walleij@linaro.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-gpio@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=sboyd@codeaurora.org \
    --cc=sramana@codeaurora.org \
    --cc=timur@codeaurora.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).