[PATCH 0/3] ADD interconnect support for USB

[PATCH 0/3] ADD interconnect support for USB

[Chandana Kishori Chiluveru]

This path series aims to add interconnect support in
dwc3-qcom driver on SDM845 SoCs.

Chandana Kishori Chiluveru (3):
  dt-bindings: Introduce interconnect bindings for usb
  usb: dwc3: qcom: Add interconnect support in dwc3 driver
  arm64: dts: sdm845: Add interconnect properties for USB

 .../devicetree/bindings/usb/qcom,dwc3.txt          |  13 ++
 arch/arm64/boot/dts/qcom/sdm845.dtsi               |  12 ++
 drivers/usb/dwc3/dwc3-qcom.c                       | 147 ++++++++++++++++++++-
 3 files changed, 170 insertions(+), 2 deletions(-)

-- 
Qualcomm India Private Limited, on behalf of Qualcomm Innovation Center, Inc.,
is a member of Code Aurora Forum, a Linux Foundation Collaborative Project.

[PATCH 1/3] dt-bindings: Introduce interconnect bindings for usb

[Chandana Kishori Chiluveru]

Add documentation for the interconnects and interconnect-names
bindings for USB as detailed by bindings/interconnect/interconnect.txt.

Signed-off-by: Chandana Kishori Chiluveru <cchiluve@codeaurora.org>
---
 Documentation/devicetree/bindings/usb/qcom,dwc3.txt | 13 +++++++++++++
 1 file changed, 13 insertions(+)

diff --git a/Documentation/devicetree/bindings/usb/qcom,dwc3.txt b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt
index cb695aa..7e9cb97 100644
--- a/Documentation/devicetree/bindings/usb/qcom,dwc3.txt
+++ b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt
@@ -33,6 +33,16 @@ Optional clocks:
 
 Optional properties:
 - resets:		Phandle to reset control that resets core and wrapper.
+- interconnects:	Pairs of phandles and interconnect provider specifier
+			to denote the edge source and destination ports of
+			the interconnect path. Please refer to
+			Documentation/devicetree/bindings/interconnect/
+			for more details.
+- interconnect-names:	List of interconnect path name strings sorted in the same
+			order as the interconnects property. Consumers drivers will use
+			interconnect-names to match interconnect paths with interconnect
+			specifiers. Please refer to Documentation/devicetree/bindings/
+			interconnect/ for more details.
 - interrupts:		specifies interrupts from controller wrapper used
 			to wakeup from low power/susepnd state.	Must contain
 			one or more entry for interrupt-names property
@@ -74,6 +84,9 @@ Example device nodes:
 			#size-cells = <1>;
 			ranges;
 
+			interconnects = <&qnoc MASTER_USB3_0 &qnoc SLAVE_EBI1>,
+					<&qnoc MASTER_APPSS_PROC &qnoc SLAVE_USB3_0>;
+			interconnect-names = "usb-ddr", "apps-usb";
 			interrupts = <0 131 0>, <0 486 0>, <0 488 0>, <0 489 0>;
 			interrupt-names = "hs_phy_irq", "ss_phy_irq",
 				  "dm_hs_phy_irq", "dp_hs_phy_irq";
-- 
Qualcomm India Private Limited, on behalf of Qualcomm Innovation Center, Inc.,
is a member of Code Aurora Forum, a Linux Foundation Collaborative Project.

[PATCH 2/3] usb: dwc3: qcom: Add interconnect support in dwc3 driver

[Chandana Kishori Chiluveru]

Add interconnect support in dwc3-qcom driver to vote for bus
bandwidth.

This requires for two different paths - from USB master to
DDR slave. The other is from APPS master to USB slave.

Signed-off-by: Chandana Kishori Chiluveru <cchiluve@codeaurora.org>
---
 drivers/usb/dwc3/dwc3-qcom.c | 147 ++++++++++++++++++++++++++++++++++++++++++-
 1 file changed, 145 insertions(+), 2 deletions(-)

diff --git a/drivers/usb/dwc3/dwc3-qcom.c b/drivers/usb/dwc3/dwc3-qcom.c
index 184df4d..4b8c2ae 100644
--- a/drivers/usb/dwc3/dwc3-qcom.c
+++ b/drivers/usb/dwc3/dwc3-qcom.c
@@ -14,6 +14,7 @@
 #include <linux/extcon.h>
 #include <linux/of_platform.h>
 #include <linux/platform_device.h>
+#include <linux/interconnect.h>
 #include <linux/phy/phy.h>
 #include <linux/usb/of.h>
 #include <linux/reset.h>
@@ -38,6 +39,9 @@
 #define PWR_EVNT_LPM_IN_L2_MASK			BIT(4)
 #define PWR_EVNT_LPM_OUT_L2_MASK		BIT(5)
 
+#define USB_DDR "usb-ddr"
+#define APPS_USB "apps-usb"
+
 struct dwc3_qcom {
 	struct device		*dev;
 	void __iomem		*qscratch_base;
@@ -59,8 +63,13 @@ struct dwc3_qcom {
 	enum usb_dr_mode	mode;
 	bool			is_suspended;
 	bool			pm_suspended;
+	struct icc_path *usb_ddr_icc_path;
+	struct icc_path *apps_usb_icc_path;
 };
 
+static int usb_interconnect_enable(struct dwc3_qcom *qcom);
+static int usb_interconnect_disable(struct dwc3_qcom *qcom);
+
 static inline void dwc3_qcom_setbits(void __iomem *base, u32 offset, u32 val)
 {
 	u32 reg;
@@ -222,7 +231,7 @@ static void dwc3_qcom_enable_interrupts(struct dwc3_qcom *qcom)
 static int dwc3_qcom_suspend(struct dwc3_qcom *qcom)
 {
 	u32 val;
-	int i;
+	int i, ret;
 
 	if (qcom->is_suspended)
 		return 0;
@@ -234,6 +243,11 @@ static int dwc3_qcom_suspend(struct dwc3_qcom *qcom)
 	for (i = qcom->num_clocks - 1; i >= 0; i--)
 		clk_disable_unprepare(qcom->clks[i]);
 
+	/* Remove bus voting */
+	ret = usb_interconnect_disable(qcom);
+	if (ret)
+		dev_err(qcom->dev, "bus bw voting failed %d\n", ret);
+
 	qcom->is_suspended = true;
 	dwc3_qcom_enable_interrupts(qcom);
 
@@ -259,6 +273,11 @@ static int dwc3_qcom_resume(struct dwc3_qcom *qcom)
 		}
 	}
 
+	/* Add bus voting */
+	ret = usb_interconnect_enable(qcom);
+	if (ret)
+		dev_err(qcom->dev, "bus bw voting failed %d\n", ret);
+
 	/* Clear existing events from PHY related to L2 in/out */
 	dwc3_qcom_setbits(qcom->qscratch_base, PWR_EVNT_IRQ_STAT_REG,
 			  PWR_EVNT_LPM_IN_L2_MASK | PWR_EVNT_LPM_OUT_L2_MASK);
@@ -409,6 +428,116 @@ static int dwc3_qcom_clk_init(struct dwc3_qcom *qcom, int count)
 	return 0;
 }
 
+/* Interconnect path bandwidths in KBps */
+#define USB_MEMORY_AVG_HS_BW 240000
+#define USB_MEMORY_PEAK_HS_BW 700000
+#define USB_MEMORY_AVG_SS_BW  1000000
+#define USB_MEMORY_PEAK_SS_BW 2500000
+#define APPS_USB_AVG_BW 0
+#define APPS_USB_PEAK_BW 40000
+
+/**
+ * usb_interconnect_init() - Request to get interconnect path handle
+ * @qcom:			Pointer to the concerned usb core.
+ *
+ */
+static int usb_interconnect_init(struct dwc3_qcom *qcom)
+{
+	struct device *dev = qcom->dev;
+
+	qcom->usb_ddr_icc_path = of_icc_get(dev, USB_DDR);
+	if (IS_ERR(qcom->usb_ddr_icc_path)) {
+		dev_err(dev, "Error: (%ld) failed getting %s path\n",
+			PTR_ERR(qcom->usb_ddr_icc_path), USB_DDR);
+		return PTR_ERR(qcom->usb_ddr_icc_path);
+	}
+
+	qcom->apps_usb_icc_path = of_icc_get(dev, APPS_USB);
+	if (IS_ERR(qcom->apps_usb_icc_path)) {
+		dev_err(dev, "Error: (%ld) failed getting %s path\n",
+				PTR_ERR(qcom->apps_usb_icc_path), APPS_USB);
+		return PTR_ERR(qcom->usb_ddr_icc_path);
+	}
+
+	return 0;
+}
+
+/**
+ * geni_interconnect_exit() - Request to release interconnect path handle
+ * @qcom:			Pointer to the concerned usb core.
+ *
+ * This function is used to release interconnect path handle.
+ */
+static void usb_interconnect_exit(struct dwc3_qcom *qcom)
+{
+	icc_put(qcom->usb_ddr_icc_path);
+	icc_put(qcom->apps_usb_icc_path);
+}
+
+/* Currently we only use bandwidth level, so just "enable" interconnects */
+static int usb_interconnect_enable(struct dwc3_qcom *qcom)
+{
+	struct dwc3 *dwc;
+	int ret;
+
+	dwc = platform_get_drvdata(qcom->dwc3);
+	if (!dwc) {
+		dev_err(qcom->dev, "Failed to get dwc3 device\n");
+		return -EPROBE_DEFER;
+	}
+
+	if (dwc->maximum_speed == USB_SPEED_SUPER) {
+		ret = icc_set_bw(qcom->usb_ddr_icc_path,
+			USB_MEMORY_AVG_SS_BW, USB_MEMORY_PEAK_SS_BW);
+		if (ret)
+			return ret;
+	} else {
+		ret = icc_set_bw(qcom->usb_ddr_icc_path,
+			USB_MEMORY_AVG_HS_BW, USB_MEMORY_PEAK_HS_BW);
+		if (ret)
+			return ret;
+	}
+
+	ret = icc_set_bw(qcom->apps_usb_icc_path,
+		APPS_USB_AVG_BW, APPS_USB_PEAK_BW);
+	if (ret)
+		goto err_disable_mem_path;
+
+	return 0;
+
+err_disable_mem_path:
+	icc_set_bw(qcom->usb_ddr_icc_path, 0, 0);
+
+	return ret;
+}
+
+/* To disable an interconnect, we just its bandwidth to 0 */
+static int usb_interconnect_disable(struct dwc3_qcom *qcom)
+{
+	struct dwc3 *dwc = platform_get_drvdata(qcom->dwc3);
+	int ret;
+
+	ret = icc_set_bw(qcom->usb_ddr_icc_path, 0, 0);
+	if (ret)
+		return ret;
+
+	ret = icc_set_bw(qcom->apps_usb_icc_path, 0, 0);
+	if (ret)
+		goto err_reenable_memory_path;
+
+	return 0;       /* Success */
+
+	/* Re-enable things in the event of an error */
+err_reenable_memory_path:
+	if (dwc->maximum_speed == USB_SPEED_SUPER)
+		icc_set_bw(qcom->usb_ddr_icc_path,
+			USB_MEMORY_AVG_SS_BW, USB_MEMORY_PEAK_SS_BW);
+	else
+		icc_set_bw(qcom->usb_ddr_icc_path,
+			USB_MEMORY_AVG_HS_BW, USB_MEMORY_PEAK_HS_BW);
+
+	return ret;
+}
 static int dwc3_qcom_probe(struct platform_device *pdev)
 {
 	struct device_node	*np = pdev->dev.of_node, *dwc3_np;
@@ -494,6 +623,17 @@ static int dwc3_qcom_probe(struct platform_device *pdev)
 		goto depopulate;
 	}
 
+	ret = usb_interconnect_init(qcom);
+	if (ret) {
+		dev_err(dev, "failed to get interconnect handle ret:%d\n", ret);
+		goto depopulate;
+	}
+	ret = usb_interconnect_enable(qcom);
+	if (ret) {
+		dev_err(qcom->dev, "bus bw voting failed %d\n", ret);
+		goto interconnect_exit;
+	}
+
 	qcom->mode = usb_get_dr_mode(&qcom->dwc3->dev);
 
 	/* enable vbus override for device mode */
@@ -503,7 +643,7 @@ static int dwc3_qcom_probe(struct platform_device *pdev)
 	/* register extcon to override sw_vbus on Vbus change later */
 	ret = dwc3_qcom_register_extcon(qcom);
 	if (ret)
-		goto depopulate;
+		goto interconnect_exit;
 
 	device_init_wakeup(&pdev->dev, 1);
 	qcom->is_suspended = false;
@@ -513,6 +653,8 @@ static int dwc3_qcom_probe(struct platform_device *pdev)
 
 	return 0;
 
+interconnect_exit:
+	usb_interconnect_exit(qcom);
 depopulate:
 	of_platform_depopulate(&pdev->dev);
 clk_disable:
@@ -540,6 +682,7 @@ static int dwc3_qcom_remove(struct platform_device *pdev)
 	}
 	qcom->num_clocks = 0;
 
+	usb_interconnect_exit(qcom);
 	reset_control_assert(qcom->resets);
 
 	pm_runtime_allow(dev);
-- 
Qualcomm India Private Limited, on behalf of Qualcomm Innovation Center, Inc.,
is a member of Code Aurora Forum, a Linux Foundation Collaborative Project.

[PATCH 3/3] arm64: dts: sdm845: Add interconnect properties for USB

[Chandana Kishori Chiluveru]

Populate USB DT node with interconnect properties.

Signed-off-by: Chandana Kishori Chiluveru <cchiluve@codeaurora.org>
---
 arch/arm64/boot/dts/qcom/sdm845.dtsi | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi
index fcb9330..1c41922 100644
--- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
@@ -1837,6 +1837,12 @@
 
 			resets = <&gcc GCC_USB30_PRIM_BCR>;
 
+			interconnects = <&rsc_hlos MASTER_USB3_0
+						&rsc_hlos SLAVE_EBI1>,
+					<&rsc_hlos MASTER_APPSS_PROC
+						&rsc_hlos SLAVE_USB3_0>;
+			interconnect-names = "usb-ddr", "apps-usb";
+
 			usb_1_dwc3: dwc3@a600000 {
 				compatible = "snps,dwc3";
 				reg = <0 0x0a600000 0 0xcd00>;
@@ -1881,6 +1887,12 @@
 
 			resets = <&gcc GCC_USB30_SEC_BCR>;
 
+			interconnects = <&rsc_hlos MASTER_USB3_1
+						&rsc_hlos SLAVE_EBI1>,
+					<&rsc_hlos MASTER_APPSS_PROC
+						&rsc_hlos SLAVE_USB3_1>;
+			interconnect-names = "usb-ddr", "apps-usb";
+
 			usb_2_dwc3: dwc3@a800000 {
 				compatible = "snps,dwc3";
 				reg = <0 0x0a800000 0 0xcd00>;
-- 
Qualcomm India Private Limited, on behalf of Qualcomm Innovation Center, Inc.,
is a member of Code Aurora Forum, a Linux Foundation Collaborative Project.

Re: [PATCH 2/3] usb: dwc3: qcom: Add interconnect support in dwc3 driver

[Georgi Djakov]

Hi Chandana,

Thank you for the patch!

On 9/11/19 07:54, Chandana Kishori Chiluveru wrote:
> Add interconnect support in dwc3-qcom driver to vote for bus
> bandwidth.
> 
> This requires for two different paths - from USB master to
> DDR slave. The other is from APPS master to USB slave.
> 
> Signed-off-by: Chandana Kishori Chiluveru <cchiluve@codeaurora.org>
> ---
>  drivers/usb/dwc3/dwc3-qcom.c | 147 ++++++++++++++++++++++++++++++++++++++++++-
>  1 file changed, 145 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/usb/dwc3/dwc3-qcom.c b/drivers/usb/dwc3/dwc3-qcom.c
> index 184df4d..4b8c2ae 100644
> --- a/drivers/usb/dwc3/dwc3-qcom.c
> +++ b/drivers/usb/dwc3/dwc3-qcom.c
> @@ -14,6 +14,7 @@
>  #include <linux/extcon.h>
>  #include <linux/of_platform.h>
>  #include <linux/platform_device.h>
> +#include <linux/interconnect.h>
>  #include <linux/phy/phy.h>
>  #include <linux/usb/of.h>
>  #include <linux/reset.h>
> @@ -38,6 +39,9 @@
>  #define PWR_EVNT_LPM_IN_L2_MASK			BIT(4)
>  #define PWR_EVNT_LPM_OUT_L2_MASK		BIT(5)
>  
> +#define USB_DDR "usb-ddr"
> +#define APPS_USB "apps-usb"

What is the benefit of adding these defines? Please remove them.

>  struct dwc3_qcom {
>  	struct device		*dev;
>  	void __iomem		*qscratch_base;
> @@ -59,8 +63,13 @@ struct dwc3_qcom {
>  	enum usb_dr_mode	mode;
>  	bool			is_suspended;
>  	bool			pm_suspended;
> +	struct icc_path *usb_ddr_icc_path;
> +	struct icc_path *apps_usb_icc_path;

Nit: Maybe try to make the indentation style consistent with the existing code?

>  };
>  
> +static int usb_interconnect_enable(struct dwc3_qcom *qcom);
> +static int usb_interconnect_disable(struct dwc3_qcom *qcom);
> +
>  static inline void dwc3_qcom_setbits(void __iomem *base, u32 offset, u32 val)
>  {
>  	u32 reg;
> @@ -222,7 +231,7 @@ static void dwc3_qcom_enable_interrupts(struct dwc3_qcom *qcom)
>  static int dwc3_qcom_suspend(struct dwc3_qcom *qcom)
>  {
>  	u32 val;
> -	int i;
> +	int i, ret;
>  
>  	if (qcom->is_suspended)
>  		return 0;
> @@ -234,6 +243,11 @@ static int dwc3_qcom_suspend(struct dwc3_qcom *qcom)
>  	for (i = qcom->num_clocks - 1; i >= 0; i--)
>  		clk_disable_unprepare(qcom->clks[i]);
>  
> +	/* Remove bus voting */
> +	ret = usb_interconnect_disable(qcom);
> +	if (ret)
> +		dev_err(qcom->dev, "bus bw voting failed %d\n", ret);
> +
>  	qcom->is_suspended = true;
>  	dwc3_qcom_enable_interrupts(qcom);
>  
> @@ -259,6 +273,11 @@ static int dwc3_qcom_resume(struct dwc3_qcom *qcom)
>  		}
>  	}
>  
> +	/* Add bus voting */
> +	ret = usb_interconnect_enable(qcom);
> +	if (ret)
> +		dev_err(qcom->dev, "bus bw voting failed %d\n", ret);
> +
>  	/* Clear existing events from PHY related to L2 in/out */
>  	dwc3_qcom_setbits(qcom->qscratch_base, PWR_EVNT_IRQ_STAT_REG,
>  			  PWR_EVNT_LPM_IN_L2_MASK | PWR_EVNT_LPM_OUT_L2_MASK);
> @@ -409,6 +428,116 @@ static int dwc3_qcom_clk_init(struct dwc3_qcom *qcom, int count)
>  	return 0;
>  }
>  
> +/* Interconnect path bandwidths in KBps */
> +#define USB_MEMORY_AVG_HS_BW 240000
> +#define USB_MEMORY_PEAK_HS_BW 700000
> +#define USB_MEMORY_AVG_SS_BW  1000000
> +#define USB_MEMORY_PEAK_SS_BW 2500000
> +#define APPS_USB_AVG_BW 0
> +#define APPS_USB_PEAK_BW 40000

I would suggest to wrap the values with kBps_to_icc() or MBps_to_icc() macro.

> +
> +/**
> + * usb_interconnect_init() - Request to get interconnect path handle
> + * @qcom:			Pointer to the concerned usb core.
> + *
> + */
> +static int usb_interconnect_init(struct dwc3_qcom *qcom)
> +{
> +	struct device *dev = qcom->dev;
> +
> +	qcom->usb_ddr_icc_path = of_icc_get(dev, USB_DDR);
> +	if (IS_ERR(qcom->usb_ddr_icc_path)) {
> +		dev_err(dev, "Error: (%ld) failed getting %s path\n",
> +			PTR_ERR(qcom->usb_ddr_icc_path), USB_DDR);
> +		return PTR_ERR(qcom->usb_ddr_icc_path);
> +	}
> +
> +	qcom->apps_usb_icc_path = of_icc_get(dev, APPS_USB);
> +	if (IS_ERR(qcom->apps_usb_icc_path)) {
> +		dev_err(dev, "Error: (%ld) failed getting %s path\n",
> +				PTR_ERR(qcom->apps_usb_icc_path), APPS_USB);
> +		return PTR_ERR(qcom->usb_ddr_icc_path);
> +	}
> +
> +	return 0;
> +}
> +
> +/**
> + * geni_interconnect_exit() - Request to release interconnect path handle
> + * @qcom:			Pointer to the concerned usb core.
> + *
> + * This function is used to release interconnect path handle.
> + */
> +static void usb_interconnect_exit(struct dwc3_qcom *qcom)
> +{
> +	icc_put(qcom->usb_ddr_icc_path);
> +	icc_put(qcom->apps_usb_icc_path);
> +}
> +
> +/* Currently we only use bandwidth level, so just "enable" interconnects */
> +static int usb_interconnect_enable(struct dwc3_qcom *qcom)
> +{
> +	struct dwc3 *dwc;
> +	int ret;
> +
> +	dwc = platform_get_drvdata(qcom->dwc3);
> +	if (!dwc) {
> +		dev_err(qcom->dev, "Failed to get dwc3 device\n");
> +		return -EPROBE_DEFER;
> +	}
> +
> +	if (dwc->maximum_speed == USB_SPEED_SUPER) {
> +		ret = icc_set_bw(qcom->usb_ddr_icc_path,
> +			USB_MEMORY_AVG_SS_BW, USB_MEMORY_PEAK_SS_BW);
> +		if (ret)
> +			return ret;
> +	} else {
> +		ret = icc_set_bw(qcom->usb_ddr_icc_path,
> +			USB_MEMORY_AVG_HS_BW, USB_MEMORY_PEAK_HS_BW);
> +		if (ret)
> +			return ret;
> +	}
> +
> +	ret = icc_set_bw(qcom->apps_usb_icc_path,
> +		APPS_USB_AVG_BW, APPS_USB_PEAK_BW);
> +	if (ret)
> +		goto err_disable_mem_path;
> +
> +	return 0;
> +
> +err_disable_mem_path:
> +	icc_set_bw(qcom->usb_ddr_icc_path, 0, 0);
> +
> +	return ret;
> +}
> +
> +/* To disable an interconnect, we just its bandwidth to 0 */

Missing the word "set"?

> +static int usb_interconnect_disable(struct dwc3_qcom *qcom)
> +{
> +	struct dwc3 *dwc = platform_get_drvdata(qcom->dwc3);
> +	int ret;
> +
> +	ret = icc_set_bw(qcom->usb_ddr_icc_path, 0, 0);
> +	if (ret)
> +		return ret;
> +
> +	ret = icc_set_bw(qcom->apps_usb_icc_path, 0, 0);
> +	if (ret)
> +		goto err_reenable_memory_path;
> +
> +	return 0;       /* Success */

Nit: This comment seems useless.

> +
> +	/* Re-enable things in the event of an error */
> +err_reenable_memory_path:
> +	if (dwc->maximum_speed == USB_SPEED_SUPER)
> +		icc_set_bw(qcom->usb_ddr_icc_path,
> +			USB_MEMORY_AVG_SS_BW, USB_MEMORY_PEAK_SS_BW);
> +	else
> +		icc_set_bw(qcom->usb_ddr_icc_path,
> +			USB_MEMORY_AVG_HS_BW, USB_MEMORY_PEAK_HS_BW);
> +
> +	return ret;
> +}
>  static int dwc3_qcom_probe(struct platform_device *pdev)
>  {
>  	struct device_node	*np = pdev->dev.of_node, *dwc3_np;
> @@ -494,6 +623,17 @@ static int dwc3_qcom_probe(struct platform_device *pdev)
>  		goto depopulate;
>  	}
>  
> +	ret = usb_interconnect_init(qcom);
> +	if (ret) {
> +		dev_err(dev, "failed to get interconnect handle ret:%d\n", ret);
> +		goto depopulate;
> +	}
> +	ret = usb_interconnect_enable(qcom);
> +	if (ret) {
> +		dev_err(qcom->dev, "bus bw voting failed %d\n", ret);
> +		goto interconnect_exit;
> +	}
> +
>  	qcom->mode = usb_get_dr_mode(&qcom->dwc3->dev);
>  
>  	/* enable vbus override for device mode */
> @@ -503,7 +643,7 @@ static int dwc3_qcom_probe(struct platform_device *pdev)
>  	/* register extcon to override sw_vbus on Vbus change later */
>  	ret = dwc3_qcom_register_extcon(qcom);
>  	if (ret)
> -		goto depopulate;
> +		goto interconnect_exit;
>  
>  	device_init_wakeup(&pdev->dev, 1);
>  	qcom->is_suspended = false;
> @@ -513,6 +653,8 @@ static int dwc3_qcom_probe(struct platform_device *pdev)
>  
>  	return 0;
>  
> +interconnect_exit:
> +	usb_interconnect_exit(qcom);
>  depopulate:
>  	of_platform_depopulate(&pdev->dev);
>  clk_disable:
> @@ -540,6 +682,7 @@ static int dwc3_qcom_remove(struct platform_device *pdev)
>  	}
>  	qcom->num_clocks = 0;
>  
> +	usb_interconnect_exit(qcom);
>  	reset_control_assert(qcom->resets);
>  
>  	pm_runtime_allow(dev);
>
The patch looks ok, but does not apply to neither mainline or linux-next.

Thanks,
Georgi

Re: [PATCH 1/3] dt-bindings: Introduce interconnect bindings for usb

[Matthias Kaehlcke]

On Wed, Sep 11, 2019 at 10:24:33AM +0530, Chandana Kishori Chiluveru wrote:
> Add documentation for the interconnects and interconnect-names
> bindings for USB as detailed by bindings/interconnect/interconnect.txt.

This isn't a generic binding for USB, but for the qcom,dwc3, the
commit message (including subject) should reflect this.

nit: you might want to replace 'bindings' with 'properties'.

> Signed-off-by: Chandana Kishori Chiluveru <cchiluve@codeaurora.org>
> ---
>  Documentation/devicetree/bindings/usb/qcom,dwc3.txt | 13 +++++++++++++
>  1 file changed, 13 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/usb/qcom,dwc3.txt b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt
> index cb695aa..7e9cb97 100644
> --- a/Documentation/devicetree/bindings/usb/qcom,dwc3.txt
> +++ b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt
> @@ -33,6 +33,16 @@ Optional clocks:
>  
>  Optional properties:
>  - resets:		Phandle to reset control that resets core and wrapper.
> +- interconnects:	Pairs of phandles and interconnect provider specifier

consistency nit: should be either 'phandle' & 'specifier' or
'phandles' & 'specifiers'.