linux-arm-msm.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Lina Iyer <ilina@codeaurora.org>
To: swboyd@chromium.org, evgreen@chromium.org, maz@kernel.org,
	linus.walleij@linaro.org
Cc: linux-kernel@vger.kernel.org, linux-arm-msm@vger.kernel.org,
	bjorn.andersson@linaro.org, mkshah@codeaurora.org,
	linux-gpio@vger.kernel.org, Lina Iyer <ilina@codeaurora.org>
Subject: [PATCH RFC v2 07/14] drivers: irqchip: pdc: additionally set type in SPI config registers
Date: Fri, 13 Sep 2019 15:59:15 -0600	[thread overview]
Message-ID: <1568411962-1022-8-git-send-email-ilina@codeaurora.org> (raw)
In-Reply-To: <1568411962-1022-1-git-send-email-ilina@codeaurora.org>

GPIOs that can be configured as wakeup are routed to the PDC wakeup
interrupt controller and from there to the GIC interrupt controller. On
some QCOM SoCs, the interface to the GIC for wakeup capable GPIOs have
additional hardware registers that need to be configured as well to
match the trigger type of the GPIO. This register interfaces the PDC to
the GIC and therefore updated from the PDC driver.

Typically, the firmware intializes the interface registers for the
wakeup capable GPIOs with commonly used GPIO trigger type, but it is
possible that a platform may want to use the GPIO differently. So, in
addition to configuring the PDC, configure the interface registers as
well.

Signed-off-by: Lina Iyer <ilina@codeaurora.org>
---
 drivers/irqchip/qcom-pdc.c | 93 ++++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 93 insertions(+)

diff --git a/drivers/irqchip/qcom-pdc.c b/drivers/irqchip/qcom-pdc.c
index 4abd775..affb0bfa 100644
--- a/drivers/irqchip/qcom-pdc.c
+++ b/drivers/irqchip/qcom-pdc.c
@@ -18,6 +18,8 @@
 #include <linux/slab.h>
 #include <linux/types.h>
 
+#include <linux/qcom_scm.h>
+
 #define PDC_MAX_IRQS		168
 #define PDC_MAX_GPIO_IRQS	256
 
@@ -35,10 +37,20 @@ struct pdc_pin_region {
 	u32 cnt;
 };
 
+struct spi_cfg_regs {
+	union {
+		u64 start;
+		void __iomem *base;
+	};
+	resource_size_t size;
+	bool scm_io;
+};
+
 static DEFINE_RAW_SPINLOCK(pdc_lock);
 static void __iomem *pdc_base;
 static struct pdc_pin_region *pdc_region;
 static int pdc_region_cnt;
+static struct spi_cfg_regs *spi_cfg;
 
 static void pdc_reg_write(int reg, u32 i, u32 val)
 {
@@ -100,6 +112,57 @@ static void qcom_pdc_gic_unmask(struct irq_data *d)
 	irq_chip_unmask_parent(d);
 }
 
+static u32 __spi_pin_read(unsigned int pin)
+{
+	void __iomem *cfg_reg = spi_cfg->base + pin * 4;
+	u64 scm_cfg_reg = spi_cfg->start + pin * 4;
+
+	if (spi_cfg->scm_io) {
+		unsigned int val;
+
+		qcom_scm_io_readl(scm_cfg_reg, &val);
+		return val;
+	} else {
+		return readl(cfg_reg);
+	}
+}
+
+static void __spi_pin_write(unsigned int pin, unsigned int val)
+{
+	void __iomem *cfg_reg = spi_cfg->base + pin * 4;
+	u64 scm_cfg_reg = spi_cfg->start + pin * 4;
+
+	if (spi_cfg->scm_io)
+		qcom_scm_io_writel(scm_cfg_reg, val);
+	else
+		writel(val, cfg_reg);
+}
+
+static int spi_configure_type(irq_hw_number_t hwirq, unsigned int type)
+{
+	int spi = hwirq - 32;
+	u32 pin = spi / 32;
+	u32 mask = BIT(spi % 32);
+	u32 val;
+	unsigned long flags;
+
+	if (!spi_cfg)
+		return 0;
+
+	if (pin * 4 > spi_cfg->size)
+		return -EFAULT;
+
+	raw_spin_lock_irqsave(&pdc_lock, flags);
+	val = __spi_pin_read(pin);
+	val &= ~mask;
+	if (type & IRQ_TYPE_LEVEL_MASK)
+		val |= mask;
+	__spi_pin_write(pin, val);
+	raw_spin_unlock_irqrestore(&pdc_lock, flags);
+
+	return 0;
+}
+
 /*
  * GIC does not handle falling edge or active low. To allow falling edge and
  * active low interrupts to be handled at GIC, PDC has an inverter that inverts
@@ -137,7 +200,9 @@ enum pdc_irq_config_bits {
 static int qcom_pdc_gic_set_type(struct irq_data *d, unsigned int type)
 {
 	int pin_out = d->hwirq;
+	int parent_hwirq = d->parent_data->hwirq;
 	enum pdc_irq_config_bits pdc_type;
+	int ret;
 
 	if (pin_out == GPIO_NO_WAKE_IRQ)
 		return 0;
@@ -168,6 +233,11 @@ static int qcom_pdc_gic_set_type(struct irq_data *d, unsigned int type)
 
 	pdc_reg_write(IRQ_i_CFG, pin_out, pdc_type);
 
+	/* Additionally, configure (only) the GPIO in the f/w */
+	ret = spi_configure_type(parent_hwirq, type);
+	if (ret)
+		return ret;
+
 	return irq_chip_set_type_parent(d, type);
 }
 
@@ -354,6 +424,7 @@ static int pdc_setup_pin_mapping(struct device_node *np)
 static int qcom_pdc_init(struct device_node *node, struct device_node *parent)
 {
 	struct irq_domain *parent_domain, *pdc_domain, *pdc_gpio_domain;
+	struct resource res;
 	int ret;
 
 	pdc_base = of_iomap(node, 0);
@@ -384,6 +455,27 @@ static int qcom_pdc_init(struct device_node *node, struct device_node *parent)
 		goto fail;
 	}
 
+	ret = of_address_to_resource(node, 1, &res);
+	if (!ret) {
+		spi_cfg = kcalloc(1, sizeof(*spi_cfg), GFP_KERNEL);
+		if (!spi_cfg) {
+			ret = -ENOMEM;
+			goto remove;
+		}
+		spi_cfg->scm_io = of_find_property(node,
+						   "qcom,scm-spi-cfg", NULL);
+		spi_cfg->size = resource_size(&res);
+		if (spi_cfg->scm_io) {
+			spi_cfg->start = res.start;
+		} else {
+			spi_cfg->base = ioremap(res.start, spi_cfg->size);
+			if (!spi_cfg->base) {
+				ret = -ENOMEM;
+				goto remove;
+			}
+		}
+	}
+
 	pdc_gpio_domain = irq_domain_create_hierarchy(parent_domain,
 						      IRQ_DOMAIN_FLAG_QCOM_PDC_WAKEUP,
 						      PDC_MAX_GPIO_IRQS,
@@ -401,6 +493,7 @@ static int qcom_pdc_init(struct device_node *node, struct device_node *parent)
 
 remove:
 	irq_domain_remove(pdc_domain);
+	kfree(spi_cfg);
 fail:
 	kfree(pdc_region);
 	iounmap(pdc_base);
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project


  parent reply	other threads:[~2019-09-13 22:00 UTC|newest]

Thread overview: 32+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-09-13 21:59 [PATCH RFC v2 00/14] Support wakeup capable GPIOs Lina Iyer
2019-09-13 21:59 ` [PATCH RFC v2 01/14] irqdomain: add bus token DOMAIN_BUS_WAKEUP Lina Iyer
2019-09-13 21:59 ` [PATCH RFC v2 02/14] drivers: irqchip: qcom-pdc: update max PDC interrupts Lina Iyer
2019-09-13 21:59 ` [PATCH RFC v2 03/14] drivers: irqchip: pdc: Do not toggle IRQ_ENABLE during mask/unmask Lina Iyer
2019-09-13 21:59 ` [PATCH RFC v2 04/14] drivers: irqchip: add PDC irqdomain for wakeup capable GPIOs Lina Iyer
2019-11-08 21:21   ` Doug Anderson
2019-11-08 21:54     ` Lina Iyer
2019-11-08 22:16       ` Lina Iyer
2019-11-08 22:57         ` Doug Anderson
2019-11-08 23:14           ` Lina Iyer
2019-09-13 21:59 ` [PATCH RFC v2 05/14] of: irq: document properties for wakeup interrupt parent Lina Iyer
2019-10-03 12:02   ` Linus Walleij
2019-11-08 21:29   ` Doug Anderson
2019-09-13 21:59 ` [PATCH RFC v2 06/14] dt-bindings/interrupt-controller: pdc: add SPI config register Lina Iyer
2019-09-30 22:14   ` Rob Herring
2019-09-30 22:33   ` Stephen Boyd
2019-10-16  6:27     ` Stephen Boyd
2019-11-05 20:58       ` Lina Iyer
2019-11-06  0:53         ` Stephen Boyd
2019-11-11 18:37           ` Lina Iyer
2019-11-12 11:52             ` Marc Zyngier
2019-09-13 21:59 ` Lina Iyer [this message]
2019-09-13 21:59 ` [PATCH RFC v2 08/14] genirq: Introduce irq_chip_get/set_parent_state calls Lina Iyer
2019-09-13 21:59 ` [PATCH RFC v2 09/14] drivers: irqchip: pdc: Add irqchip set/get state calls Lina Iyer
2019-09-13 21:59 ` [PATCH RFC v2 10/14] drivers: pinctrl: msm: setup GPIO chip in hierarchy Lina Iyer
2019-10-03 12:17   ` Linus Walleij
2019-11-13 18:35     ` Lina Iyer
2019-09-13 21:59 ` [PATCH RFC v2 11/14] drivers: pinctrl: sdm845: add PDC wakeup interrupt map for GPIOs Lina Iyer
2019-10-03 12:18   ` Linus Walleij
2019-09-13 21:59 ` [PATCH RFC v2 12/14] arm64: dts: qcom: add PDC interrupt controller for SDM845 Lina Iyer
2019-09-13 21:59 ` [PATCH RFC v2 13/14] arm64: dts: qcom: setup PDC as the wakeup parent for TLMM on SDM845 Lina Iyer
2019-09-13 21:59 ` [PATCH RFC v2 14/14] arm64: defconfig: enable PDC interrupt controller for Qualcomm SDM845 Lina Iyer

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1568411962-1022-8-git-send-email-ilina@codeaurora.org \
    --to=ilina@codeaurora.org \
    --cc=bjorn.andersson@linaro.org \
    --cc=evgreen@chromium.org \
    --cc=linus.walleij@linaro.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-gpio@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=maz@kernel.org \
    --cc=mkshah@codeaurora.org \
    --cc=swboyd@chromium.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).