[PATCH v1 0/2] Add suppport for rm69299 Visionox panel driver and add devicetree bindings for visionox panel.

[PATCH v1 0/2] Add suppport for rm69299 Visionox panel driver and add devicetree bindings for visionox panel.

[Harigovindan P]

Current patchset adds support for rm69299 visionox panel driver used in MSM reference platforms.
The visionox panel driver supports a resolution of 1080x2248 with 4 lanes and supports only single DSI mode.

Current patchset is tested on actual panel.

Changes in v1:
	-add devicetree bindings for visionox panel.
	-Split out panel driver patch from dsi config changes(Rob Clark).
        -Remove unrelated code(Stephen Boyd).
        -Remove static arrays to make regulator setup
         open coded in probe(Stephen Boyd).
        -Remove pre-assigning variables(Stephen Boyd).
        -Inline panel_add function into probe(Stephen Boyd).
        -Use mipi_dsi_dcs_write directly(Rob Clark).
	-Remove qcom_rm69299_1080p_panel_magic_cmds array(Rob Clark).

Harigovindan P (2):
  dt-bindings: display: add sc7180 panel variant
  drm/panel: add support for rm69299 visionox panel driver

 .../bindings/display/visionox,rm69299.txt          |  68 ++++
 drivers/gpu/drm/panel/Kconfig                      |   9 +
 drivers/gpu/drm/panel/Makefile                     |   1 +
 drivers/gpu/drm/panel/panel-visionox-rm69299.c     | 412 +++++++++++++++++++++
 4 files changed, 490 insertions(+)
 create mode 100755 Documentation/devicetree/bindings/display/visionox,rm69299.txt
 create mode 100755 drivers/gpu/drm/panel/panel-visionox-rm69299.c

-- 
2.7.4

[PATCH v1 1/2] dt-bindings: display: add sc7180 panel variant

[Harigovindan P]

Add a compatible string to support sc7180 panel version.

Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
---
 .../bindings/display/visionox,rm69299.txt          | 68 ++++++++++++++++++++++
 1 file changed, 68 insertions(+)
 create mode 100755 Documentation/devicetree/bindings/display/visionox,rm69299.txt

diff --git a/Documentation/devicetree/bindings/display/visionox,rm69299.txt b/Documentation/devicetree/bindings/display/visionox,rm69299.txt
new file mode 100755
index 0000000..4622191
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/visionox,rm69299.txt
@@ -0,0 +1,68 @@
+Visionox model RM69299 DSI display driver
+
+The Visionox RM69299 is a generic display driver, currently only configured
+for use in the 1080p display on the Qualcomm SC7180 MTP board.
+
+Required properties:
+- compatible: should be "visionox,rm69299-1080p-display"
+- vdda-supply: phandle of the regulator that provides the supply voltage
+  Power IC supply
+- vdd3p3-supply: phandle of the regulator that provides the supply voltage
+  Power IC supply
+- reset-gpios: phandle of gpio for reset line
+  This should be 8mA, gpio can be configured using mux, pinctrl, pinctrl-names
+  (active low)
+- mode-gpios: phandle of the gpio for choosing the mode of the display
+  for single DSI
+- ports: This device has one video port driven by one DSI. Their connections
+  are modeled using the OF graph bindings specified in
+  Documentation/devicetree/bindings/graph.txt.
+  - port@0: DSI input port driven by master DSI
+
+Example:
+
+	dsi@ae94000 {
+		panel@0 {
+			compatible = "visionox,rm69299-1080p-display";
+			reg = <0>;
+
+			vdda-supply = <&src_pp1800_l8c>;
+			vdd3p3-supply = <&src_pp2800_l18a>;
+
+			pinctrl-names = "default", "suspend";
+			pinctrl-0 = <&disp_pins_default>;
+			pinctrl-1 = <&disp_pins_default>;
+
+			reset-gpios = <&pm6150l_gpios 3 0>;
+
+			display-timings {
+				timing0: timing-0 {
+					/* originally
+					 * 268316160 Mhz,
+					 * but value below fits
+					 * better w/ downstream
+					 */
+					clock-frequency = <158695680>;
+					hactive = <1080>;
+					vactive = <2248>;
+					hfront-porch = <26>;
+					hback-porch = <36>;
+					hsync-len = <2>;
+					vfront-porch = <56>;
+					vback-porch = <4>;
+					vsync-len = <4>;
+				};
+			};
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				port@0 {
+					reg = <0>;
+					panel0_in: endpoint {
+						remote-endpoint = <&dsi0_out>;
+					};
+				};
+			};
+		};
+	};
-- 
2.7.4

[PATCH v1 2/2] drm/panel: add support for rm69299 visionox panel driver

[Harigovindan P]

Add support for Visionox panel driver.

Changes in v1:
	-Split out panel driver patch from dsi config changes(Rob Clark).
        -Remove unrelated code(Stephen Boyd).
        -Remove static arrays to make regulator setup open coded
	 in probe(Stephen Boyd).
        -Remove pre-assigning variables(Stephen Boyd).
        -Inline panel_add function into probe(Stephen Boyd).
        -Use mipi_dsi_dcs_write directly(Rob Clark).
	-Remove qcom_rm69299_1080p_panel_magic_cmds array(Rob Clark).

Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
---
 drivers/gpu/drm/panel/Kconfig                  |   9 +
 drivers/gpu/drm/panel/Makefile                 |   1 +
 drivers/gpu/drm/panel/panel-visionox-rm69299.c | 412 +++++++++++++++++++++++++
 3 files changed, 422 insertions(+)
 create mode 100755 drivers/gpu/drm/panel/panel-visionox-rm69299.c

diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
index f152bc4..c06c403 100644
--- a/drivers/gpu/drm/panel/Kconfig
+++ b/drivers/gpu/drm/panel/Kconfig
@@ -355,4 +355,13 @@ config DRM_PANEL_TRULY_NT35597_WQXGA
 	help
 	  Say Y here if you want to enable support for Truly NT35597 WQXGA Dual DSI
 	  Video Mode panel
+
+config DRM_PANEL_VISIONOX_RM69299
+	tristate "Visionox RM69299"
+	depends on OF
+	depends on DRM_MIPI_DSI
+	help
+	  Say Y here if you want to enable support for Visionox
+	  RM69299  DSI Video Mode panel.
+
 endmenu
diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile
index b6cd39f..6f1e4c6 100644
--- a/drivers/gpu/drm/panel/Makefile
+++ b/drivers/gpu/drm/panel/Makefile
@@ -38,3 +38,4 @@ obj-$(CONFIG_DRM_PANEL_TPO_TD028TTEC1) += panel-tpo-td028ttec1.o
 obj-$(CONFIG_DRM_PANEL_TPO_TD043MTEA1) += panel-tpo-td043mtea1.o
 obj-$(CONFIG_DRM_PANEL_TPO_TPG110) += panel-tpo-tpg110.o
 obj-$(CONFIG_DRM_PANEL_TRULY_NT35597_WQXGA) += panel-truly-nt35597.o
+obj-$(CONFIG_DRM_PANEL_VISIONOX_RM69299) += panel-visionox-rm69299.o
diff --git a/drivers/gpu/drm/panel/panel-visionox-rm69299.c b/drivers/gpu/drm/panel/panel-visionox-rm69299.c
new file mode 100755
index 0000000..da86714
--- /dev/null
+++ b/drivers/gpu/drm/panel/panel-visionox-rm69299.c
@@ -0,0 +1,412 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2019, The Linux Foundation. All rights reserved.
+ */
+
+#include <drm/drm_panel.h>
+#include <drm/drm_mipi_dsi.h>
+#include <drm/drm_modes.h>
+#include <drm/drm_print.h>
+
+#include <linux/gpio/consumer.h>
+#include <linux/of_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/backlight.h>
+#include <linux/module.h>
+#include <linux/delay.h>
+
+#include <video/mipi_display.h>
+
+struct rm69299_config {
+	unsigned long width_mm;
+	unsigned long height_mm;
+	const char *panel_name;
+	u32 num_on_cmds;
+	const struct drm_display_mode *dm;
+};
+
+struct visionox_rm69299 {
+	struct device *dev;
+	struct drm_panel panel;
+
+	struct regulator_bulk_data supplies[2];
+
+	struct gpio_desc *reset_gpio;
+
+	struct backlight_device *backlight;
+
+	struct mipi_dsi_device *dsi;
+	const struct rm69299_config *config;
+	bool prepared;
+	bool enabled;
+};
+
+static inline struct visionox_rm69299 *panel_to_ctx(struct drm_panel *panel)
+{
+	return container_of(panel, struct visionox_rm69299, panel);
+}
+
+static int visionox_35597_power_on(struct visionox_rm69299 *ctx)
+{
+	int ret;
+
+	ret = regulator_set_load(ctx->supplies[0].consumer, 32000);
+	if (ret)
+		return ret;
+
+	ret = regulator_set_load(ctx->supplies[1].consumer, 13200);
+	if (ret)
+		return ret;
+
+	ret = regulator_bulk_enable(ARRAY_SIZE(ctx->supplies), ctx->supplies);
+	if (ret < 0)
+		return ret;
+
+	/*
+	 * Reset sequence of visionox panel requires the panel to be
+	 * out of reset for 10ms, followed by being held in reset
+	 * for 10ms and then out again
+	 */
+	gpiod_set_value(ctx->reset_gpio, 1);
+	usleep_range(10000, 20000);
+	gpiod_set_value(ctx->reset_gpio, 0);
+	usleep_range(10000, 20000);
+	gpiod_set_value(ctx->reset_gpio, 1);
+	usleep_range(10000, 20000);
+
+	return 0;
+}
+
+static int visionox_rm69299_power_off(struct visionox_rm69299 *ctx)
+{
+	int ret;
+
+	gpiod_set_value(ctx->reset_gpio, 0);
+
+	ret = regulator_set_load(ctx->supplies[0].consumer, 80);
+
+	if (ret) {
+		DRM_DEV_ERROR(ctx->dev,
+			"regulator_set_load failed %d\n", ret);
+		return ret;
+	}
+
+	ret = regulator_set_load(ctx->supplies[1].consumer, 80);
+
+	if (ret) {
+		DRM_DEV_ERROR(ctx->dev,
+			"regulator_set_load failed %d\n", ret);
+		return ret;
+	}
+
+	ret = regulator_bulk_disable(ARRAY_SIZE(ctx->supplies), ctx->supplies);
+	if (ret) {
+		DRM_DEV_ERROR(ctx->dev,
+			"regulator_bulk_disable failed %d\n", ret);
+	}
+	return ret;
+}
+
+static int visionox_rm69299_disable(struct drm_panel *panel)
+{
+	struct visionox_rm69299 *ctx = panel_to_ctx(panel);
+	int ret;
+
+	if (!ctx->enabled)
+		return 0;
+
+	ret = backlight_disable(ctx->backlight);
+	if (ret < 0)
+		DRM_DEV_ERROR(ctx->dev, "backlight disable failed %d\n",
+		ret);
+
+	ctx->enabled = false;
+	return 0;
+}
+
+static int visionox_rm69299_unprepare(struct drm_panel *panel)
+{
+	struct visionox_rm69299 *ctx = panel_to_ctx(panel);
+	int ret;
+
+	if (!ctx->prepared)
+		return 0;
+
+	ctx->dsi->mode_flags = 0;
+
+	ret = mipi_dsi_dcs_write(ctx->dsi, MIPI_DCS_SET_DISPLAY_OFF, NULL, 0);
+	if (ret < 0) {
+		DRM_DEV_ERROR(ctx->dev,
+			"set_display_off cmd failed ret = %d\n",
+			ret);
+	}
+
+	/* 120ms delay required here as per DCS spec */
+	msleep(120);
+
+	ret = mipi_dsi_dcs_write(ctx->dsi, MIPI_DCS_ENTER_SLEEP_MODE, NULL, 0);
+	if (ret < 0) {
+		DRM_DEV_ERROR(ctx->dev,
+			"enter_sleep cmd failed ret = %d\n", ret);
+	}
+
+	ret = visionox_rm69299_power_off(ctx);
+	if (ret < 0)
+		DRM_DEV_ERROR(ctx->dev, "power_off failed ret = %d\n", ret);
+
+	ctx->prepared = false;
+	return ret;
+}
+
+static int visionox_rm69299_prepare(struct drm_panel *panel)
+{
+	struct visionox_rm69299 *ctx = panel_to_ctx(panel);
+	int ret;
+	const struct rm69299_config *config;
+
+	if (ctx->prepared)
+		return 0;
+
+	ret = visionox_35597_power_on(ctx);
+	if (ret < 0)
+		return ret;
+
+	ctx->dsi->mode_flags |= MIPI_DSI_MODE_LPM;
+
+	config = ctx->config;
+
+	ret = mipi_dsi_dcs_write_buffer(ctx->dsi, (u8[]){ 0xfe, 0x00 }, 2);
+	if (ret < 0) {
+		DRM_DEV_ERROR(ctx->dev,
+		"cmd set tx 0 failed, ret = %d\n",
+		ret);
+		goto power_off;
+	}
+
+	ret = mipi_dsi_dcs_write_buffer(ctx->dsi, (u8[]){ 0xc2, 0x08 }, 2);
+	if (ret < 0) {
+		DRM_DEV_ERROR(ctx->dev,
+		"cmd set tx 1 failed, ret = %d\n",
+		ret);
+		goto power_off;
+	}
+
+	ret = mipi_dsi_dcs_write_buffer(ctx->dsi, (u8[]){ 0x35, 0x00 }, 2);
+	if (ret < 0) {
+		DRM_DEV_ERROR(ctx->dev,
+		"cmd set tx 2 failed, ret = %d\n",
+		ret);
+		goto power_off;
+	}
+
+	ret = mipi_dsi_dcs_write_buffer(ctx->dsi, (u8[]){ 0x51, 0xff }, 2);
+	if (ret < 0) {
+		DRM_DEV_ERROR(ctx->dev,
+		"cmd set tx 3 failed, ret = %d\n",
+		ret);
+		goto power_off;
+	}
+
+	ret = mipi_dsi_dcs_write(ctx->dsi, MIPI_DCS_EXIT_SLEEP_MODE, NULL, 0);
+	if (ret < 0) {
+		DRM_DEV_ERROR(ctx->dev,
+			"exit_sleep_mode cmd failed ret = %d\n",
+			ret);
+		goto power_off;
+	}
+
+	/* Per DSI spec wait 120ms after sending exit sleep DCS command */
+	msleep(120);
+
+	ret = mipi_dsi_dcs_write(ctx->dsi, MIPI_DCS_SET_DISPLAY_ON, NULL, 0);
+	if (ret < 0) {
+		DRM_DEV_ERROR(ctx->dev,
+			"set_display_on cmd failed ret = %d\n", ret);
+		goto power_off;
+	}
+
+	/* Per DSI spec wait 120ms after sending set_display_on DCS command */
+	msleep(120);
+
+	ctx->prepared = true;
+
+	return 0;
+
+power_off:
+	if (visionox_rm69299_power_off(ctx))
+		DRM_DEV_ERROR(ctx->dev, "power_off failed\n");
+	return ret;
+}
+
+static int visionox_rm69299_enable(struct drm_panel *panel)
+{
+	struct visionox_rm69299 *ctx = panel_to_ctx(panel);
+	int ret;
+
+	if (ctx->enabled)
+		return 0;
+
+	ret = backlight_enable(ctx->backlight);
+	if (ret < 0)
+		DRM_DEV_ERROR(ctx->dev, "backlight enable failed %d\n",
+		ret);
+
+	ctx->enabled = true;
+
+	return 0;
+}
+
+static int visionox_rm69299_get_modes(struct drm_panel *panel)
+{
+	struct drm_connector *connector = panel->connector;
+	struct visionox_rm69299 *ctx = panel_to_ctx(panel);
+	struct drm_display_mode *mode;
+	const struct rm69299_config *config;
+
+	config = ctx->config;
+	mode = drm_mode_create(connector->dev);
+	if (!mode) {
+		DRM_DEV_ERROR(ctx->dev,
+			"failed to create a new display mode\n");
+		return 0;
+	}
+
+	connector->display_info.width_mm = config->width_mm;
+	connector->display_info.height_mm = config->height_mm;
+	drm_mode_copy(mode, config->dm);
+	mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;
+	drm_mode_probed_add(connector, mode);
+
+	return 1;
+}
+
+static const struct drm_panel_funcs visionox_rm69299_drm_funcs = {
+	.disable = visionox_rm69299_disable,
+	.unprepare = visionox_rm69299_unprepare,
+	.prepare = visionox_rm69299_prepare,
+	.enable = visionox_rm69299_enable,
+	.get_modes = visionox_rm69299_get_modes,
+};
+
+static const struct drm_display_mode qcom_sc7180_mtp_1080p_mode = {
+	.name = "1080x2248",
+	.clock = 158695,
+	.hdisplay = 1080,
+	.hsync_start = 1080 + 26,
+	.hsync_end = 1080 + 26 + 2,
+	.htotal = 1080 + 26 + 2 + 36,
+	.vdisplay = 2248,
+	.vsync_start = 2248 + 56,
+	.vsync_end = 2248 + 56 + 4,
+	.vtotal = 2248 + 56 + 4 + 4,
+	.vrefresh = 60,
+	.flags = 0,
+};
+
+static const struct rm69299_config rm69299_dir = {
+	.width_mm = 74,
+	.height_mm = 131,
+	.panel_name = "qcom_sc7180_mtp_1080p_panel",
+	.dm = &qcom_sc7180_mtp_1080p_mode,
+};
+
+static int visionox_rm69299_probe(struct mipi_dsi_device *dsi)
+{
+	struct device *dev = &dsi->dev;
+	struct device *device;
+	struct visionox_rm69299 *ctx;
+	const struct rm69299_config *config;
+	int ret;
+
+	ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
+
+	if (!ctx)
+		return -ENOMEM;
+
+	ctx->config = device_get_match_data(dev);
+
+	if (!ctx->config) {
+		dev_err(dev, "missing device configuration\n");
+		return -ENODEV;
+	}
+
+	mipi_dsi_set_drvdata(dsi, ctx);
+
+	ctx->dev = dev;
+	ctx->dsi = dsi;
+
+	device = ctx->dev;
+
+	config = ctx->config;
+	ctx->supplies[0].supply = "vdda";
+	ctx->supplies[1].supply = "vdd3p3";
+
+	ret = devm_regulator_bulk_get(device, ARRAY_SIZE(ctx->supplies),
+								ctx->supplies);
+	if (ret < 0)
+		return ret;
+
+	ctx->reset_gpio = devm_gpiod_get(device, "reset", GPIOD_OUT_LOW);
+	if (IS_ERR(ctx->reset_gpio)) {
+		DRM_DEV_ERROR(dev, "cannot get reset gpio %ld\n",
+					PTR_ERR(ctx->reset_gpio));
+		return PTR_ERR(ctx->reset_gpio);
+	}
+
+	drm_panel_init(&ctx->panel);
+	ctx->panel.dev = device;
+	ctx->panel.funcs = &visionox_rm69299_drm_funcs;
+	drm_panel_add(&ctx->panel);
+
+	dsi->lanes = 4;
+	dsi->format = MIPI_DSI_FMT_RGB888;
+	dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_LPM |
+		MIPI_DSI_CLOCK_NON_CONTINUOUS;
+	ret = mipi_dsi_attach(dsi);
+	if (ret < 0) {
+		DRM_DEV_ERROR(dev,
+			"dsi attach failed ret = %d\n", ret);
+		goto err_dsi_attach;
+	}
+
+	return 0;
+
+err_dsi_attach:
+	drm_panel_remove(&ctx->panel);
+	return ret;
+}
+
+static int visionox_rm69299_remove(struct mipi_dsi_device *dsi)
+{
+	struct visionox_rm69299 *ctx = mipi_dsi_get_drvdata(dsi);
+
+	if (ctx->dsi) {
+		mipi_dsi_detach(ctx->dsi);
+		mipi_dsi_device_unregister(ctx->dsi);
+	}
+
+	drm_panel_remove(&ctx->panel);
+	return 0;
+}
+
+static const struct of_device_id visionox_rm69299_of_match[] = {
+	{
+		.compatible = "visionox,rm69299-1080p-display",
+		.data = &rm69299_dir,
+	},
+	{ }
+};
+MODULE_DEVICE_TABLE(of, visionox_rm69299_of_match);
+
+static struct mipi_dsi_driver visionox_rm69299_driver = {
+	.driver = {
+		.name = "panel-visionox-rm69299",
+		.of_match_table = visionox_rm69299_of_match,
+	},
+	.probe = visionox_rm69299_probe,
+	.remove = visionox_rm69299_remove,
+};
+module_mipi_dsi_driver(visionox_rm69299_driver);
+
+MODULE_DESCRIPTION("VISIONOX RM69299 DSI Panel Driver");
+MODULE_LICENSE("GPL v2");
-- 
2.7.4

Re: [Freedreno] [PATCH v1 1/2] dt-bindings: display: add sc7180 panel variant

[Rob Clark]

On Thu, Nov 28, 2019 at 10:56 PM Harigovindan P <harigovi@codeaurora.org> wrote:
>
> Add a compatible string to support sc7180 panel version.
>
> Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
> ---
>  .../bindings/display/visionox,rm69299.txt          | 68 ++++++++++++++++++++++
>  1 file changed, 68 insertions(+)
>  create mode 100755 Documentation/devicetree/bindings/display/visionox,rm69299.txt
>
> diff --git a/Documentation/devicetree/bindings/display/visionox,rm69299.txt b/Documentation/devicetree/bindings/display/visionox,rm69299.txt
> new file mode 100755
> index 0000000..4622191
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/visionox,rm69299.txt
> @@ -0,0 +1,68 @@
> +Visionox model RM69299 DSI display driver
> +
> +The Visionox RM69299 is a generic display driver, currently only configured
> +for use in the 1080p display on the Qualcomm SC7180 MTP board.
> +
> +Required properties:
> +- compatible: should be "visionox,rm69299-1080p-display"
> +- vdda-supply: phandle of the regulator that provides the supply voltage
> +  Power IC supply
> +- vdd3p3-supply: phandle of the regulator that provides the supply voltage
> +  Power IC supply
> +- reset-gpios: phandle of gpio for reset line
> +  This should be 8mA, gpio can be configured using mux, pinctrl, pinctrl-names
> +  (active low)
> +- mode-gpios: phandle of the gpio for choosing the mode of the display
> +  for single DSI
> +- ports: This device has one video port driven by one DSI. Their connections
> +  are modeled using the OF graph bindings specified in
> +  Documentation/devicetree/bindings/graph.txt.
> +  - port@0: DSI input port driven by master DSI
> +
> +Example:
> +
> +       dsi@ae94000 {
> +               panel@0 {
> +                       compatible = "visionox,rm69299-1080p-display";
> +                       reg = <0>;
> +
> +                       vdda-supply = <&src_pp1800_l8c>;
> +                       vdd3p3-supply = <&src_pp2800_l18a>;
> +
> +                       pinctrl-names = "default", "suspend";
> +                       pinctrl-0 = <&disp_pins_default>;
> +                       pinctrl-1 = <&disp_pins_default>;
> +
> +                       reset-gpios = <&pm6150l_gpios 3 0>;
> +
> +                       display-timings {
> +                               timing0: timing-0 {
> +                                       /* originally
> +                                        * 268316160 Mhz,
> +                                        * but value below fits
> +                                        * better w/ downstream
> +                                        */
> +                                       clock-frequency = <158695680>;
> +                                       hactive = <1080>;
> +                                       vactive = <2248>;
> +                                       hfront-porch = <26>;
> +                                       hback-porch = <36>;
> +                                       hsync-len = <2>;
> +                                       vfront-porch = <56>;
> +                                       vback-porch = <4>;
> +                                       vsync-len = <4>;
> +                               };

why do we specify timings in dt?  Would the panel use different
timings on a different board?

BR,
-R

> +                       };
> +
> +                       ports {
> +                               #address-cells = <1>;
> +                               #size-cells = <0>;
> +                               port@0 {
> +                                       reg = <0>;
> +                                       panel0_in: endpoint {
> +                                               remote-endpoint = <&dsi0_out>;
> +                                       };
> +                               };
> +                       };
> +               };
> +       };
> --
> 2.7.4
>
> _______________________________________________
> Freedreno mailing list
> Freedreno@lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/freedreno

Re: [PATCH v1 1/2] dt-bindings: display: add sc7180 panel variant

[Rob Herring]

On Fri, Nov 29, 2019 at 12:25:44PM +0530, Harigovindan P wrote:
> Add a compatible string to support sc7180 panel version.
> 
> Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
> ---
>  .../bindings/display/visionox,rm69299.txt          | 68 ++++++++++++++++++++++
>  1 file changed, 68 insertions(+)
>  create mode 100755 Documentation/devicetree/bindings/display/visionox,rm69299.txt

Source files should not have execute permission.

New bindings should be in DT schema format.

checkpatch.pl will tell you both of these things.

> 
> diff --git a/Documentation/devicetree/bindings/display/visionox,rm69299.txt b/Documentation/devicetree/bindings/display/visionox,rm69299.txt
> new file mode 100755
> index 0000000..4622191
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/visionox,rm69299.txt
> @@ -0,0 +1,68 @@
> +Visionox model RM69299 DSI display driver
> +
> +The Visionox RM69299 is a generic display driver, currently only configured
> +for use in the 1080p display on the Qualcomm SC7180 MTP board.
> +
> +Required properties:
> +- compatible: should be "visionox,rm69299-1080p-display"

RM69299 may be generic, but 1080p sounds like a specific panel.

Is there anything besides a 'display'? If not, '-display' is redundant.

> +- vdda-supply: phandle of the regulator that provides the supply voltage
> +  Power IC supply
> +- vdd3p3-supply: phandle of the regulator that provides the supply voltage
> +  Power IC supply
> +- reset-gpios: phandle of gpio for reset line
> +  This should be 8mA, gpio can be configured using mux, pinctrl, pinctrl-names
> +  (active low)
> +- mode-gpios: phandle of the gpio for choosing the mode of the display
> +  for single DSI

The modes are what?

> +- ports: This device has one video port driven by one DSI. Their connections
> +  are modeled using the OF graph bindings specified in
> +  Documentation/devicetree/bindings/graph.txt.
> +  - port@0: DSI input port driven by master DSI
> +
> +Example:
> +
> +	dsi@ae94000 {
> +		panel@0 {
> +			compatible = "visionox,rm69299-1080p-display";
> +			reg = <0>;
> +
> +			vdda-supply = <&src_pp1800_l8c>;
> +			vdd3p3-supply = <&src_pp2800_l18a>;
> +
> +			pinctrl-names = "default", "suspend";
> +			pinctrl-0 = <&disp_pins_default>;
> +			pinctrl-1 = <&disp_pins_default>;
> +
> +			reset-gpios = <&pm6150l_gpios 3 0>;
> +
> +			display-timings {
> +				timing0: timing-0 {
> +					/* originally
> +					 * 268316160 Mhz,
> +					 * but value below fits
> +					 * better w/ downstream
> +					 */
> +					clock-frequency = <158695680>;
> +					hactive = <1080>;
> +					vactive = <2248>;
> +					hfront-porch = <26>;
> +					hback-porch = <36>;
> +					hsync-len = <2>;
> +					vfront-porch = <56>;
> +					vback-porch = <4>;
> +					vsync-len = <4>;
> +				};
> +			};
> +
> +			ports {
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +				port@0 {
> +					reg = <0>;
> +					panel0_in: endpoint {
> +						remote-endpoint = <&dsi0_out>;
> +					};
> +				};
> +			};
> +		};
> +	};
> -- 
> 2.7.4
> 

Re: [PATCH v1 2/2] drm/panel: add support for rm69299 visionox panel driver

[Sam Ravnborg]

Hi Harigovindan.

Thanks for re-submitting this driver.
There is several more or less trivial comments below.
Please fix and send a v3.

Thanks,

	Sam

On Fri, Nov 29, 2019 at 12:25:45PM +0530, Harigovindan P wrote:
> Add support for Visionox panel driver.
> 
> Changes in v1:
> 	-Split out panel driver patch from dsi config changes(Rob Clark).
>         -Remove unrelated code(Stephen Boyd).
>         -Remove static arrays to make regulator setup open coded
> 	 in probe(Stephen Boyd).
>         -Remove pre-assigning variables(Stephen Boyd).
>         -Inline panel_add function into probe(Stephen Boyd).
>         -Use mipi_dsi_dcs_write directly(Rob Clark).
> 	-Remove qcom_rm69299_1080p_panel_magic_cmds array(Rob Clark).
> 
> Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
> ---
>  drivers/gpu/drm/panel/Kconfig                  |   9 +
>  drivers/gpu/drm/panel/Makefile                 |   1 +
>  drivers/gpu/drm/panel/panel-visionox-rm69299.c | 412 +++++++++++++++++++++++++
>  3 files changed, 422 insertions(+)
>  create mode 100755 drivers/gpu/drm/panel/panel-visionox-rm69299.c
> 
> diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
> index f152bc4..c06c403 100644
> --- a/drivers/gpu/drm/panel/Kconfig
> +++ b/drivers/gpu/drm/panel/Kconfig
> @@ -355,4 +355,13 @@ config DRM_PANEL_TRULY_NT35597_WQXGA
>  	help
>  	  Say Y here if you want to enable support for Truly NT35597 WQXGA Dual DSI
>  	  Video Mode panel
> +
> +config DRM_PANEL_VISIONOX_RM69299
> +	tristate "Visionox RM69299"
> +	depends on OF
> +	depends on DRM_MIPI_DSI
> +	help
> +	  Say Y here if you want to enable support for Visionox
> +	  RM69299  DSI Video Mode panel.
Drop redundant space.

> +
>  endmenu
> diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile
> index b6cd39f..6f1e4c6 100644
> --- a/drivers/gpu/drm/panel/Makefile
> +++ b/drivers/gpu/drm/panel/Makefile
> @@ -38,3 +38,4 @@ obj-$(CONFIG_DRM_PANEL_TPO_TD028TTEC1) += panel-tpo-td028ttec1.o
>  obj-$(CONFIG_DRM_PANEL_TPO_TD043MTEA1) += panel-tpo-td043mtea1.o
>  obj-$(CONFIG_DRM_PANEL_TPO_TPG110) += panel-tpo-tpg110.o
>  obj-$(CONFIG_DRM_PANEL_TRULY_NT35597_WQXGA) += panel-truly-nt35597.o
> +obj-$(CONFIG_DRM_PANEL_VISIONOX_RM69299) += panel-visionox-rm69299.o
> diff --git a/drivers/gpu/drm/panel/panel-visionox-rm69299.c b/drivers/gpu/drm/panel/panel-visionox-rm69299.c
> new file mode 100755
> index 0000000..da86714
> --- /dev/null
> +++ b/drivers/gpu/drm/panel/panel-visionox-rm69299.c
> @@ -0,0 +1,412 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2019, The Linux Foundation. All rights reserved.
> + */
> +
> +#include <drm/drm_panel.h>
> +#include <drm/drm_mipi_dsi.h>
> +#include <drm/drm_modes.h>
> +#include <drm/drm_print.h>
> +
> +#include <linux/gpio/consumer.h>
> +#include <linux/of_device.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/backlight.h>
> +#include <linux/module.h>
> +#include <linux/delay.h>
> +
> +#include <video/mipi_display.h>

Please use following structure for include files:
#include <linux/*>

#include <video/*>

#include <drm/*>

#include ""

And within each block sort the include lines alphabetically.

> +
> +struct rm69299_config {
> +	unsigned long width_mm;
> +	unsigned long height_mm;
> +	const char *panel_name;
> +	u32 num_on_cmds;
> +	const struct drm_display_mode *dm;
> +};
> +
> +struct visionox_rm69299 {
> +	struct device *dev;
> +	struct drm_panel panel;
> +
> +	struct regulator_bulk_data supplies[2];
> +
> +	struct gpio_desc *reset_gpio;
> +
> +	struct backlight_device *backlight;
backlight is never assigned - drop it.
Your binding does not mention backligth so
this seems to be correct to drop it.

> +
> +	struct mipi_dsi_device *dsi;
> +	const struct rm69299_config *config;
> +	bool prepared;
> +	bool enabled;
> +};
> +
> +static inline struct visionox_rm69299 *panel_to_ctx(struct drm_panel *panel)
> +{
> +	return container_of(panel, struct visionox_rm69299, panel);
> +}
> +
> +static int visionox_35597_power_on(struct visionox_rm69299 *ctx)
> +{
> +	int ret;
> +
> +	ret = regulator_set_load(ctx->supplies[0].consumer, 32000);
> +	if (ret)
> +		return ret;
> +
> +	ret = regulator_set_load(ctx->supplies[1].consumer, 13200);
> +	if (ret)
> +		return ret;
> +
> +	ret = regulator_bulk_enable(ARRAY_SIZE(ctx->supplies), ctx->supplies);
> +	if (ret < 0)
> +		return ret;
> +
> +	/*
> +	 * Reset sequence of visionox panel requires the panel to be
> +	 * out of reset for 10ms, followed by being held in reset
> +	 * for 10ms and then out again
> +	 */
> +	gpiod_set_value(ctx->reset_gpio, 1);
> +	usleep_range(10000, 20000);
> +	gpiod_set_value(ctx->reset_gpio, 0);
> +	usleep_range(10000, 20000);
> +	gpiod_set_value(ctx->reset_gpio, 1);
> +	usleep_range(10000, 20000);
> +
> +	return 0;
> +}
> +
> +static int visionox_rm69299_power_off(struct visionox_rm69299 *ctx)
> +{
> +	int ret;
> +
> +	gpiod_set_value(ctx->reset_gpio, 0);
> +
> +	ret = regulator_set_load(ctx->supplies[0].consumer, 80);
> +
> +	if (ret) {
> +		DRM_DEV_ERROR(ctx->dev,
> +			"regulator_set_load failed %d\n", ret);
> +		return ret;
> +	}
> +
> +	ret = regulator_set_load(ctx->supplies[1].consumer, 80);

It looks wrong that you have to change regulator_set_load()
just before the regulators are disabled.
> +
> +	if (ret) {
> +		DRM_DEV_ERROR(ctx->dev,
> +			"regulator_set_load failed %d\n", ret);
> +		return ret;
> +	}
> +
> +	ret = regulator_bulk_disable(ARRAY_SIZE(ctx->supplies), ctx->supplies);
> +	if (ret) {
> +		DRM_DEV_ERROR(ctx->dev,
> +			"regulator_bulk_disable failed %d\n", ret);
> +	}
> +	return ret;
> +}
> +
> +static int visionox_rm69299_disable(struct drm_panel *panel)
> +{
> +	struct visionox_rm69299 *ctx = panel_to_ctx(panel);
> +	int ret;
> +
> +	if (!ctx->enabled)
> +		return 0;
> +
> +	ret = backlight_disable(ctx->backlight);
> +	if (ret < 0)
> +		DRM_DEV_ERROR(ctx->dev, "backlight disable failed %d\n",
> +		ret);
> +
> +	ctx->enabled = false;
> +	return 0;
> +}
With backlight dropped this function is no logner needed.

> +
> +static int visionox_rm69299_unprepare(struct drm_panel *panel)
> +{
> +	struct visionox_rm69299 *ctx = panel_to_ctx(panel);
> +	int ret;
> +
> +	if (!ctx->prepared)
> +		return 0;
> +
> +	ctx->dsi->mode_flags = 0;
> +
> +	ret = mipi_dsi_dcs_write(ctx->dsi, MIPI_DCS_SET_DISPLAY_OFF, NULL, 0);
> +	if (ret < 0) {
> +		DRM_DEV_ERROR(ctx->dev,
> +			"set_display_off cmd failed ret = %d\n",
> +			ret);
> +	}
> +
> +	/* 120ms delay required here as per DCS spec */
> +	msleep(120);
> +
> +	ret = mipi_dsi_dcs_write(ctx->dsi, MIPI_DCS_ENTER_SLEEP_MODE, NULL, 0);
> +	if (ret < 0) {
> +		DRM_DEV_ERROR(ctx->dev,
> +			"enter_sleep cmd failed ret = %d\n", ret);
> +	}
> +
> +	ret = visionox_rm69299_power_off(ctx);
> +	if (ret < 0)
> +		DRM_DEV_ERROR(ctx->dev, "power_off failed ret = %d\n", ret);
visionox_rm69299_power_off() already printed an error message. No need
for two errors messages.
> +
> +	ctx->prepared = false;
> +	return ret;
> +}
> +
> +static int visionox_rm69299_prepare(struct drm_panel *panel)
> +{
> +	struct visionox_rm69299 *ctx = panel_to_ctx(panel);
> +	int ret;
> +	const struct rm69299_config *config;
> +
> +	if (ctx->prepared)
> +		return 0;
> +
> +	ret = visionox_35597_power_on(ctx);
> +	if (ret < 0)
> +		return ret;
> +
> +	ctx->dsi->mode_flags |= MIPI_DSI_MODE_LPM;
> +
> +	config = ctx->config;
> +
> +	ret = mipi_dsi_dcs_write_buffer(ctx->dsi, (u8[]){ 0xfe, 0x00 }, 2);
> +	if (ret < 0) {
> +		DRM_DEV_ERROR(ctx->dev,
> +		"cmd set tx 0 failed, ret = %d\n",
> +		ret);
> +		goto power_off;
> +	}
> +
> +	ret = mipi_dsi_dcs_write_buffer(ctx->dsi, (u8[]){ 0xc2, 0x08 }, 2);
> +	if (ret < 0) {
> +		DRM_DEV_ERROR(ctx->dev,
> +		"cmd set tx 1 failed, ret = %d\n",
> +		ret);
> +		goto power_off;
> +	}
> +
> +	ret = mipi_dsi_dcs_write_buffer(ctx->dsi, (u8[]){ 0x35, 0x00 }, 2);
> +	if (ret < 0) {
> +		DRM_DEV_ERROR(ctx->dev,
> +		"cmd set tx 2 failed, ret = %d\n",
> +		ret);
> +		goto power_off;
> +	}
> +
> +	ret = mipi_dsi_dcs_write_buffer(ctx->dsi, (u8[]){ 0x51, 0xff }, 2);
> +	if (ret < 0) {
> +		DRM_DEV_ERROR(ctx->dev,
> +		"cmd set tx 3 failed, ret = %d\n",
> +		ret);
> +		goto power_off;
> +	}
> +
> +	ret = mipi_dsi_dcs_write(ctx->dsi, MIPI_DCS_EXIT_SLEEP_MODE, NULL, 0);
> +	if (ret < 0) {
> +		DRM_DEV_ERROR(ctx->dev,
> +			"exit_sleep_mode cmd failed ret = %d\n",
> +			ret);
> +		goto power_off;
> +	}
> +
> +	/* Per DSI spec wait 120ms after sending exit sleep DCS command */
> +	msleep(120);
> +
> +	ret = mipi_dsi_dcs_write(ctx->dsi, MIPI_DCS_SET_DISPLAY_ON, NULL, 0);
> +	if (ret < 0) {
> +		DRM_DEV_ERROR(ctx->dev,
> +			"set_display_on cmd failed ret = %d\n", ret);
> +		goto power_off;
> +	}
> +
> +	/* Per DSI spec wait 120ms after sending set_display_on DCS command */
> +	msleep(120);
> +
> +	ctx->prepared = true;
> +
> +	return 0;
> +
> +power_off:
> +	if (visionox_rm69299_power_off(ctx))
> +		DRM_DEV_ERROR(ctx->dev, "power_off failed\n");
No need for two error messages. visionox_rm69299_power_off() alredy
printed an error message.

> +	return ret;
> +}
> +
> +static int visionox_rm69299_enable(struct drm_panel *panel)
> +{
> +	struct visionox_rm69299 *ctx = panel_to_ctx(panel);
> +	int ret;
> +
> +	if (ctx->enabled)
> +		return 0;
> +
> +	ret = backlight_enable(ctx->backlight);
> +	if (ret < 0)
> +		DRM_DEV_ERROR(ctx->dev, "backlight enable failed %d\n",
> +		ret);
> +
> +	ctx->enabled = true;
> +
> +	return 0;
> +}
With backlight dropped there is no need for this function.

> +
> +static int visionox_rm69299_get_modes(struct drm_panel *panel)
In drm-misc-next this function takes drm_connector as an argument.
Please update.

> +{
> +	struct drm_connector *connector = panel->connector;
> +	struct visionox_rm69299 *ctx = panel_to_ctx(panel);
> +	struct drm_display_mode *mode;
> +	const struct rm69299_config *config;
> +
> +	config = ctx->config;
> +	mode = drm_mode_create(connector->dev);
> +	if (!mode) {
> +		DRM_DEV_ERROR(ctx->dev,
> +			"failed to create a new display mode\n");
> +		return 0;
> +	}
> +
> +	connector->display_info.width_mm = config->width_mm;
> +	connector->display_info.height_mm = config->height_mm;
> +	drm_mode_copy(mode, config->dm);
> +	mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;
> +	drm_mode_probed_add(connector, mode);
> +
> +	return 1;
> +}
> +
> +static const struct drm_panel_funcs visionox_rm69299_drm_funcs = {
> +	.disable = visionox_rm69299_disable,
> +	.unprepare = visionox_rm69299_unprepare,
> +	.prepare = visionox_rm69299_prepare,
> +	.enable = visionox_rm69299_enable,
> +	.get_modes = visionox_rm69299_get_modes,
> +};
> +
> +static const struct drm_display_mode qcom_sc7180_mtp_1080p_mode = {
> +	.name = "1080x2248",
> +	.clock = 158695,
> +	.hdisplay = 1080,
> +	.hsync_start = 1080 + 26,
> +	.hsync_end = 1080 + 26 + 2,
> +	.htotal = 1080 + 26 + 2 + 36,
> +	.vdisplay = 2248,
> +	.vsync_start = 2248 + 56,
> +	.vsync_end = 2248 + 56 + 4,
> +	.vtotal = 2248 + 56 + 4 + 4,
> +	.vrefresh = 60,
> +	.flags = 0,
> +};
> +
> +static const struct rm69299_config rm69299_dir = {
> +	.width_mm = 74,
> +	.height_mm = 131,
> +	.panel_name = "qcom_sc7180_mtp_1080p_panel",
> +	.dm = &qcom_sc7180_mtp_1080p_mode,
> +};
> +
> +static int visionox_rm69299_probe(struct mipi_dsi_device *dsi)
> +{
> +	struct device *dev = &dsi->dev;
> +	struct device *device;
> +	struct visionox_rm69299 *ctx;
> +	const struct rm69299_config *config;
> +	int ret;
> +
> +	ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
> +
> +	if (!ctx)
> +		return -ENOMEM;
> +
> +	ctx->config = device_get_match_data(dev);
> +
> +	if (!ctx->config) {
> +		dev_err(dev, "missing device configuration\n");
> +		return -ENODEV;
> +	}
> +
> +	mipi_dsi_set_drvdata(dsi, ctx);
> +
> +	ctx->dev = dev;
> +	ctx->dsi = dsi;
> +
> +	device = ctx->dev;
> +
> +	config = ctx->config;
> +	ctx->supplies[0].supply = "vdda";
> +	ctx->supplies[1].supply = "vdd3p3";
> +
> +	ret = devm_regulator_bulk_get(device, ARRAY_SIZE(ctx->supplies),
> +								ctx->supplies);
> +	if (ret < 0)
> +		return ret;
> +
> +	ctx->reset_gpio = devm_gpiod_get(device, "reset", GPIOD_OUT_LOW);
> +	if (IS_ERR(ctx->reset_gpio)) {
> +		DRM_DEV_ERROR(dev, "cannot get reset gpio %ld\n",
> +					PTR_ERR(ctx->reset_gpio));
> +		return PTR_ERR(ctx->reset_gpio);
> +	}
> +
> +	drm_panel_init(&ctx->panel);
> +	ctx->panel.dev = device;
> +	ctx->panel.funcs = &visionox_rm69299_drm_funcs;
> +	drm_panel_add(&ctx->panel);
> +
> +	dsi->lanes = 4;
> +	dsi->format = MIPI_DSI_FMT_RGB888;
> +	dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_LPM |
> +		MIPI_DSI_CLOCK_NON_CONTINUOUS;
> +	ret = mipi_dsi_attach(dsi);
> +	if (ret < 0) {
> +		DRM_DEV_ERROR(dev,
> +			"dsi attach failed ret = %d\n", ret);
> +		goto err_dsi_attach;
> +	}
> +
> +	return 0;
> +
> +err_dsi_attach:
> +	drm_panel_remove(&ctx->panel);
> +	return ret;
> +}
> +
> +static int visionox_rm69299_remove(struct mipi_dsi_device *dsi)
> +{
> +	struct visionox_rm69299 *ctx = mipi_dsi_get_drvdata(dsi);
> +
> +	if (ctx->dsi) {
> +		mipi_dsi_detach(ctx->dsi);
> +		mipi_dsi_device_unregister(ctx->dsi);
> +	}
> +
> +	drm_panel_remove(&ctx->panel);
> +	return 0;
> +}
> +
> +static const struct of_device_id visionox_rm69299_of_match[] = {
> +	{
> +		.compatible = "visionox,rm69299-1080p-display",
Must be updated to the new binding as per Rob's comments.

> +		.data = &rm69299_dir,
> +	},
> +	{ }
Use { /* sentinel */ },


> +};
> +MODULE_DEVICE_TABLE(of, visionox_rm69299_of_match);
> +
> +static struct mipi_dsi_driver visionox_rm69299_driver = {
> +	.driver = {
> +		.name = "panel-visionox-rm69299",
> +		.of_match_table = visionox_rm69299_of_match,
> +	},
> +	.probe = visionox_rm69299_probe,
> +	.remove = visionox_rm69299_remove,
> +};
> +module_mipi_dsi_driver(visionox_rm69299_driver);
> +
> +MODULE_DESCRIPTION("VISIONOX RM69299 DSI Panel Driver");
> +MODULE_LICENSE("GPL v2");
> -- 
> 2.7.4
> 
> _______________________________________________
> dri-devel mailing list
> dri-devel@lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/dri-devel