Linux-ARM-MSM Archive on lore.kernel.org
 help / color / Atom feed
* [PATCH v3 0/4] Add SS/HS-USB changes for Qualcomm SM8150 chipset
@ 2020-03-25 17:43 Wesley Cheng
  2020-03-25 17:43 ` [PATCH v3 1/4] dt-bindings: phy: Add binding for qcom,usb-hs-7nm Wesley Cheng
                   ` (3 more replies)
  0 siblings, 4 replies; 6+ messages in thread
From: Wesley Cheng @ 2020-03-25 17:43 UTC (permalink / raw)
  To: agross, bjorn.andersson, kishon, robh+dt, mark.rutland, p.zabel
  Cc: linux-arm-msm, linux-kernel, devicetree, Wesley Cheng

This series adds support for the Synopsis 7nm HSPHY USB driver being
used in QCOM chipsets.  The HSPHY register map differs compared to 
other PHY revisions.  In addition, modifications and updates are done
to the QMP driver to add new registers/offsets, and to update the
initialization sequence for enabling the SSUSB path on SM8150.

Changes in v3:
 - Use devm_reset_control_get_exclusive instead of referencing index for
   reset handle

Changes in v2:
 - Fixed YAML errors caught by dt_binding_check

Jack Pham (1):
  phy: qcom-qmp: Add SM8150 QMP USB3 PHY support

Wesley Cheng (3):
  dt-bindings: phy: Add binding for qcom,usb-hs-7nm
  phy: qcom-snps: Add SNPS USB PHY driver for QCOM based SOCs
  phy: qcom-qmp: Use proper PWRDOWN offset for sm8150 USB

 .../devicetree/bindings/phy/qcom,usb-hs-7nm.yaml   |  76 ++++++
 drivers/phy/qualcomm/Kconfig                       |  10 +
 drivers/phy/qualcomm/Makefile                      |   1 +
 drivers/phy/qualcomm/phy-qcom-qmp.c                | 157 +++++++++++
 drivers/phy/qualcomm/phy-qcom-qmp.h                | 198 +++++++++++++-
 drivers/phy/qualcomm/phy-qcom-snps-7nm.c           | 294 +++++++++++++++++++++
 6 files changed, 734 insertions(+), 2 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/phy/qcom,usb-hs-7nm.yaml
 create mode 100644 drivers/phy/qualcomm/phy-qcom-snps-7nm.c

-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

^ permalink raw reply	[flat|nested] 6+ messages in thread

* [PATCH v3 1/4] dt-bindings: phy: Add binding for qcom,usb-hs-7nm
  2020-03-25 17:43 [PATCH v3 0/4] Add SS/HS-USB changes for Qualcomm SM8150 chipset Wesley Cheng
@ 2020-03-25 17:43 ` Wesley Cheng
  2020-03-25 17:43 ` [PATCH v3 2/4] phy: qcom-snps: Add SNPS USB PHY driver for QCOM based SOCs Wesley Cheng
                   ` (2 subsequent siblings)
  3 siblings, 0 replies; 6+ messages in thread
From: Wesley Cheng @ 2020-03-25 17:43 UTC (permalink / raw)
  To: agross, bjorn.andersson, kishon, robh+dt, mark.rutland, p.zabel
  Cc: linux-arm-msm, linux-kernel, devicetree, Wesley Cheng

This binding shows the descriptions and properties for the
7nm Synopsis HS USB PHY used on QCOM platforms.

Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
---
 .../devicetree/bindings/phy/qcom,usb-hs-7nm.yaml   | 76 ++++++++++++++++++++++
 1 file changed, 76 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/phy/qcom,usb-hs-7nm.yaml

diff --git a/Documentation/devicetree/bindings/phy/qcom,usb-hs-7nm.yaml b/Documentation/devicetree/bindings/phy/qcom,usb-hs-7nm.yaml
new file mode 100644
index 0000000..7292e27
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/qcom,usb-hs-7nm.yaml
@@ -0,0 +1,76 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/phy/qcom,usb-hs-7nm.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Qualcomm Synopsys 7nm High-Speed USB PHY
+
+maintainers:
+  - Wesley Cheng <wcheng@codeaurora.org>
+
+description: |
+  Qualcomm Hi-Speed 7nm USB PHY
+
+properties:
+  compatible:
+    enum:
+      - qcom,usb-snps-hs-7nm-phy
+      - qcom,sm8150-usb-hs-phy
+
+  reg:
+    maxItems: 1
+
+  "#phy-cells":
+    const: 0
+
+  clocks:
+    items:
+      - description: rpmhcc ref clock
+
+  clock-names:
+    items:
+      - const: ref
+
+  resets:
+    items:
+      - description: PHY core reset
+
+  vdda-pll-supply:
+    description: phandle to the regulator VDD supply node.
+
+  vdda18-supply:
+    description: phandle to the regulator 1.8V supply node.
+
+  vdda33-supply:
+    description: phandle to the regulator 3.3V supply node.
+
+required:
+  - compatible
+  - reg
+  - "#phy-cells"
+  - clocks
+  - clock-names
+  - resets
+  - vdda-pll-supply
+  - vdda18-supply
+  - vdda33-supply
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/qcom,rpmh.h>
+    #include <dt-bindings/clock/qcom,gcc-sm8150.h>
+    usb_1_hsphy: phy@88e2000 {
+        compatible = "qcom,sm8150-usb-hs-phy";
+        reg = <0 0x088e2000 0 0x400>;
+        status = "disabled";
+        #phy-cells = <0>;
+
+        clocks = <&rpmhcc RPMH_CXO_CLK>;
+        clock-names = "ref";
+
+        resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
+    };
+...
\ No newline at end of file
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

^ permalink raw reply	[flat|nested] 6+ messages in thread

* [PATCH v3 2/4] phy: qcom-snps: Add SNPS USB PHY driver for QCOM based SOCs
  2020-03-25 17:43 [PATCH v3 0/4] Add SS/HS-USB changes for Qualcomm SM8150 chipset Wesley Cheng
  2020-03-25 17:43 ` [PATCH v3 1/4] dt-bindings: phy: Add binding for qcom,usb-hs-7nm Wesley Cheng
@ 2020-03-25 17:43 ` Wesley Cheng
  2020-03-25 17:43 ` [PATCH v3 3/4] phy: qcom-qmp: Add SM8150 QMP USB3 PHY support Wesley Cheng
  2020-03-25 17:43 ` [PATCH v3 4/4] phy: qcom-qmp: Use proper PWRDOWN offset for sm8150 USB Wesley Cheng
  3 siblings, 0 replies; 6+ messages in thread
From: Wesley Cheng @ 2020-03-25 17:43 UTC (permalink / raw)
  To: agross, bjorn.andersson, kishon, robh+dt, mark.rutland, p.zabel
  Cc: linux-arm-msm, linux-kernel, devicetree, Wesley Cheng

This adds the SNPS FemtoPHY driver used in QCOM SOCs.  There
are potentially multiple instances of this UTMI PHY on the
SOC, all which can utilize this driver.

Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Reviewed-by: Philipp Zabel <pza@pengutronix.de>
---
 drivers/phy/qualcomm/Kconfig             |  10 ++
 drivers/phy/qualcomm/Makefile            |   1 +
 drivers/phy/qualcomm/phy-qcom-snps-7nm.c | 294 +++++++++++++++++++++++++++++++
 3 files changed, 305 insertions(+)
 create mode 100644 drivers/phy/qualcomm/phy-qcom-snps-7nm.c

diff --git a/drivers/phy/qualcomm/Kconfig b/drivers/phy/qualcomm/Kconfig
index e46824d..3158c14 100644
--- a/drivers/phy/qualcomm/Kconfig
+++ b/drivers/phy/qualcomm/Kconfig
@@ -85,6 +85,16 @@ config PHY_QCOM_USB_HS
 	  Support for the USB high-speed ULPI compliant phy on Qualcomm
 	  chipsets.
 
+config PHY_QCOM_USB_SNPS_HS_7NM
+	tristate "Qualcomm 7nm USB HS PHY module"
+	depends on OF && (ARCH_QCOM || COMPILE_TEST)
+	select GENERIC_PHY
+	help
+	  Enable support for the USB high-speed SNPS phy on Qualcomm 7nm
+	  chipsets.  This PHY has differences in the register map compared
+	  to the 28nm variant.  The PHY is paired with a Synopsys DWC3 USB
+	  controller on MSM SOCs.
+
 config PHY_QCOM_USB_HSIC
 	tristate "Qualcomm USB HSIC ULPI PHY module"
 	depends on USB_ULPI_BUS
diff --git a/drivers/phy/qualcomm/Makefile b/drivers/phy/qualcomm/Makefile
index 283251d..06bdb40 100644
--- a/drivers/phy/qualcomm/Makefile
+++ b/drivers/phy/qualcomm/Makefile
@@ -10,3 +10,4 @@ obj-$(CONFIG_PHY_QCOM_UFS_14NM)		+= phy-qcom-ufs-qmp-14nm.o
 obj-$(CONFIG_PHY_QCOM_UFS_20NM)		+= phy-qcom-ufs-qmp-20nm.o
 obj-$(CONFIG_PHY_QCOM_USB_HS) 		+= phy-qcom-usb-hs.o
 obj-$(CONFIG_PHY_QCOM_USB_HSIC) 	+= phy-qcom-usb-hsic.o
+obj-$(CONFIG_PHY_QCOM_USB_SNPS_HS_7NM)		+= phy-qcom-snps-7nm.o
diff --git a/drivers/phy/qualcomm/phy-qcom-snps-7nm.c b/drivers/phy/qualcomm/phy-qcom-snps-7nm.c
new file mode 100644
index 0000000..00a46cd
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-snps-7nm.c
@@ -0,0 +1,294 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2020, The Linux Foundation. All rights reserved.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+#include <linux/reset.h>
+#include <linux/slab.h>
+
+#define USB2_PHY_USB_PHY_UTMI_CTRL0		(0x3c)
+#define OPMODE_MASK					GENMASK(4, 3)
+#define OPMODE_NORMAL				(0x00)
+#define OPMODE_NONDRIVING			BIT(3)
+#define SLEEPM						BIT(0)
+#define TERMSEL						BIT(5)
+
+#define USB2_PHY_USB_PHY_UTMI_CTRL1		(0x40)
+#define XCVRSEL						BIT(0)
+
+#define USB2_PHY_USB_PHY_UTMI_CTRL5		(0x50)
+#define POR							BIT(1)
+
+#define USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON0	(0x54)
+#define RETENABLEN							BIT(3)
+#define FSEL_MASK							GENMASK(7, 5)
+#define FSEL_DEFAULT						(0x3 << 4)
+
+#define USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON1	(0x58)
+#define VBUSVLDEXTSEL0						BIT(4)
+#define PLLBTUNE							BIT(5)
+
+#define USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON2	(0x5c)
+#define VREGBYPASS							BIT(0)
+
+#define USB2_PHY_USB_PHY_HS_PHY_CTRL1	(0x60)
+#define VBUSVLDEXT0					BIT(0)
+
+#define USB2_PHY_USB_PHY_HS_PHY_CTRL2	(0x64)
+#define USB2_AUTO_RESUME			BIT(0)
+#define USB2_SUSPEND_N				BIT(2)
+#define USB2_SUSPEND_N_SEL			BIT(3)
+
+#define USB2_PHY_USB_PHY_CFG0					(0x94)
+#define UTMI_PHY_DATAPATH_CTRL_OVERRIDE_EN	BIT(0)
+#define UTMI_PHY_CMN_CTRL_OVERRIDE_EN		BIT(1)
+
+#define USB2_PHY_USB_PHY_REFCLK_CTRL	(0xa0)
+#define REFCLK_SEL_MASK				GENMASK(1, 0)
+#define REFCLK_SEL_DEFAULT			(0x2 << 0)
+
+static const char * const qcom_snps_hsphy_vreg_names[] = {
+	"vdda-pll", "vdda33", "vdda18",
+};
+
+#define SNPS_HS_NUM_VREGS		ARRAY_SIZE(qcom_snps_hsphy_vreg_names)
+
+/**
+ * struct qcom_snps_hsphy - structure holding snps hs phy attributes
+ *
+ * @phy: generic phy
+ * @base: iomapped memory space for qubs2 phy
+ *
+ * @cfg_ahb_clk: AHB2PHY interface clock
+ * @ref_clk: phy reference clock
+ * @iface_clk: phy interface clock
+ * @phy_reset: phy reset control
+ * @vregs: regulator supplies bulk data
+
+ * @phy_initialized: if PHY has been initialized correctly
+ *
+ */
+struct qcom_snps_hsphy {
+	struct phy *phy;
+	void __iomem *base;
+
+	struct clk *cfg_ahb_clk;
+	struct clk *ref_clk;
+	struct reset_control *phy_reset;
+	struct regulator_bulk_data vregs[SNPS_HS_NUM_VREGS];
+
+	bool phy_initialized;
+};
+
+static inline void qcom_snps_hsphy_write_mask(void __iomem *base, u32 offset,
+				    u32 mask, u32 val)
+{
+	u32 reg;
+
+	reg = readl(base + offset);
+	reg &= ~mask;
+	reg |= val & mask;
+	writel(reg, base + offset);
+
+	/* Ensure above write is completed */
+	readl(base + offset);
+}
+
+static int qcom_snps_hsphy_init(struct phy *phy)
+{
+	struct qcom_snps_hsphy *hsphy = phy_get_drvdata(phy);
+	int ret;
+
+	dev_vdbg(&phy->dev, "%s(): Initializing SNPS HS phy\n", __func__);
+
+	/* turn on regulator supplies */
+	ret = regulator_bulk_enable(ARRAY_SIZE(hsphy->vregs), hsphy->vregs);
+	if (ret)
+		return ret;
+
+	/* enable ahb interface clock to program phy */
+	ret = clk_prepare_enable(hsphy->cfg_ahb_clk);
+	if (ret) {
+		dev_err(&phy->dev, "failed to enable cfg ahb clock, %d\n", ret);
+		goto poweroff_phy;
+	}
+
+	/* Perform phy reset */
+	ret = reset_control_assert(hsphy->phy_reset);
+	if (ret) {
+		dev_err(&phy->dev, "failed to assert phy_reset, %d\n", ret);
+		goto disable_ahb_clk;
+	}
+
+	/* 100 us delay to keep PHY in reset mode */
+	usleep_range(100, 150);
+
+	ret = reset_control_deassert(hsphy->phy_reset);
+	if (ret) {
+		dev_err(&phy->dev, "failed to de-assert phy_reset, %d\n", ret);
+		goto disable_ahb_clk;
+	}
+
+	qcom_snps_hsphy_write_mask(hsphy->base, USB2_PHY_USB_PHY_CFG0,
+							UTMI_PHY_CMN_CTRL_OVERRIDE_EN,
+							UTMI_PHY_CMN_CTRL_OVERRIDE_EN);
+	qcom_snps_hsphy_write_mask(hsphy->base, USB2_PHY_USB_PHY_UTMI_CTRL5,
+							POR, POR);
+	qcom_snps_hsphy_write_mask(hsphy->base, USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON0,
+							FSEL_MASK, 0);
+	qcom_snps_hsphy_write_mask(hsphy->base, USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON1,
+					PLLBTUNE, PLLBTUNE);
+	qcom_snps_hsphy_write_mask(hsphy->base, USB2_PHY_USB_PHY_REFCLK_CTRL,
+					REFCLK_SEL_DEFAULT, REFCLK_SEL_MASK);
+	qcom_snps_hsphy_write_mask(hsphy->base, USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON1,
+					VBUSVLDEXTSEL0, VBUSVLDEXTSEL0);
+	qcom_snps_hsphy_write_mask(hsphy->base, USB2_PHY_USB_PHY_HS_PHY_CTRL1,
+					VBUSVLDEXT0, VBUSVLDEXT0);
+
+	qcom_snps_hsphy_write_mask(hsphy->base, USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON2,
+					VREGBYPASS, VREGBYPASS);
+
+	qcom_snps_hsphy_write_mask(hsphy->base, USB2_PHY_USB_PHY_HS_PHY_CTRL2,
+					USB2_SUSPEND_N_SEL | USB2_SUSPEND_N,
+					USB2_SUSPEND_N_SEL | USB2_SUSPEND_N);
+
+	qcom_snps_hsphy_write_mask(hsphy->base, USB2_PHY_USB_PHY_UTMI_CTRL0,
+					SLEEPM, SLEEPM);
+
+	qcom_snps_hsphy_write_mask(hsphy->base, USB2_PHY_USB_PHY_UTMI_CTRL5,
+					POR, 0);
+
+	qcom_snps_hsphy_write_mask(hsphy->base, USB2_PHY_USB_PHY_HS_PHY_CTRL2,
+					USB2_SUSPEND_N_SEL, 0);
+
+	qcom_snps_hsphy_write_mask(hsphy->base, USB2_PHY_USB_PHY_CFG0,
+					UTMI_PHY_CMN_CTRL_OVERRIDE_EN, 0);
+
+	hsphy->phy_initialized = true;
+
+	return 0;
+
+disable_ahb_clk:
+	clk_disable_unprepare(hsphy->cfg_ahb_clk);
+poweroff_phy:
+	regulator_bulk_disable(ARRAY_SIZE(hsphy->vregs), hsphy->vregs);
+
+	return ret;
+}
+
+static int qcom_snps_hsphy_exit(struct phy *phy)
+{
+	struct qcom_snps_hsphy *hsphy = phy_get_drvdata(phy);
+
+	reset_control_assert(hsphy->phy_reset);
+	clk_disable_unprepare(hsphy->cfg_ahb_clk);
+	regulator_bulk_disable(ARRAY_SIZE(hsphy->vregs), hsphy->vregs);
+	hsphy->phy_initialized = false;
+
+	return 0;
+}
+
+static const struct phy_ops qcom_snps_hsphy_gen_ops = {
+	.init		= qcom_snps_hsphy_init,
+	.exit		= qcom_snps_hsphy_exit,
+	.owner		= THIS_MODULE,
+};
+
+static const struct of_device_id qcom_snps_hsphy_of_match_table[] = {
+	{
+		.compatible	= "qcom,sm8150-usb-hs-phy",
+	},
+	{
+		.compatible	= "qcom,usb-snps-hs-7nm-phy",
+	},
+	{ },
+};
+MODULE_DEVICE_TABLE(of, qcom_snps_hsphy_of_match_table);
+
+static int qcom_snps_hsphy_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct qcom_snps_hsphy *hsphy;
+	struct phy_provider *phy_provider;
+	struct phy *generic_phy;
+	struct resource *res;
+	int ret, i;
+	int num;
+
+	hsphy = devm_kzalloc(dev, sizeof(*hsphy), GFP_KERNEL);
+	if (!hsphy)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	hsphy->base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(hsphy->base))
+		return PTR_ERR(hsphy->base);
+
+	hsphy->ref_clk = devm_clk_get(dev, "ref");
+	if (IS_ERR(hsphy->ref_clk)) {
+		ret = PTR_ERR(hsphy->ref_clk);
+		if (ret != -EPROBE_DEFER)
+			dev_err(dev, "failed to get ref clk, %d\n", ret);
+		return ret;
+	}
+
+	hsphy->phy_reset = devm_reset_control_get_exclusive(&pdev->dev, NULL);
+	if (IS_ERR(hsphy->phy_reset)) {
+		dev_err(dev, "failed to get phy core reset\n");
+		return PTR_ERR(hsphy->phy_reset);
+	}
+
+	num = ARRAY_SIZE(hsphy->vregs);
+	for (i = 0; i < num; i++)
+		hsphy->vregs[i].supply = qcom_snps_hsphy_vreg_names[i];
+
+	ret = devm_regulator_bulk_get(dev, num, hsphy->vregs);
+	if (ret) {
+		if (ret != -EPROBE_DEFER)
+			dev_err(dev, "failed to get regulator supplies: %d\n",
+				ret);
+		return ret;
+	}
+
+	generic_phy = devm_phy_create(dev, NULL, &qcom_snps_hsphy_gen_ops);
+	if (IS_ERR(generic_phy)) {
+		ret = PTR_ERR(generic_phy);
+		dev_err(dev, "failed to create phy, %d\n", ret);
+		return ret;
+	}
+	hsphy->phy = generic_phy;
+
+	dev_set_drvdata(dev, hsphy);
+	phy_set_drvdata(generic_phy, hsphy);
+
+	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+	if (!IS_ERR(phy_provider))
+		dev_info(dev, "Registered Qcom-SNPS HS phy\n");
+
+	return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static struct platform_driver qcom_snps_hsphy_driver = {
+	.probe		= qcom_snps_hsphy_probe,
+	.driver = {
+		.name	= "qcom-snps-hs-7nm-phy",
+		.of_match_table = qcom_snps_hsphy_of_match_table,
+	},
+};
+
+module_platform_driver(qcom_snps_hsphy_driver);
+
+MODULE_DESCRIPTION("Qualcomm 7nm USB HS PHY driver");
+MODULE_LICENSE("GPL v2");
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

^ permalink raw reply	[flat|nested] 6+ messages in thread

* [PATCH v3 3/4] phy: qcom-qmp: Add SM8150 QMP USB3 PHY support
  2020-03-25 17:43 [PATCH v3 0/4] Add SS/HS-USB changes for Qualcomm SM8150 chipset Wesley Cheng
  2020-03-25 17:43 ` [PATCH v3 1/4] dt-bindings: phy: Add binding for qcom,usb-hs-7nm Wesley Cheng
  2020-03-25 17:43 ` [PATCH v3 2/4] phy: qcom-snps: Add SNPS USB PHY driver for QCOM based SOCs Wesley Cheng
@ 2020-03-25 17:43 ` Wesley Cheng
  2020-03-25 17:43 ` [PATCH v3 4/4] phy: qcom-qmp: Use proper PWRDOWN offset for sm8150 USB Wesley Cheng
  3 siblings, 0 replies; 6+ messages in thread
From: Wesley Cheng @ 2020-03-25 17:43 UTC (permalink / raw)
  To: agross, bjorn.andersson, kishon, robh+dt, mark.rutland, p.zabel
  Cc: linux-arm-msm, linux-kernel, devicetree, Jack Pham, Wesley Cheng

From: Jack Pham <jackp@codeaurora.org>

Add support for SM8150 QMP USB3 PHY with the necessary
initialization sequences as well as additional QMP V4
register definitions.

Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
---
 drivers/phy/qualcomm/phy-qcom-qmp.c | 153 ++++++++++++++++++++++++++++
 drivers/phy/qualcomm/phy-qcom-qmp.h | 198 +++++++++++++++++++++++++++++++++++-
 2 files changed, 349 insertions(+), 2 deletions(-)

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
index 7db2a94..cc04471 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
@@ -160,6 +160,12 @@ enum qphy_reg_layout {
 	[QPHY_PCS_LFPS_RXTERM_IRQ_STATUS] = 0x170,
 };
 
+static const unsigned int qmp_v4_usb3phy_regs_layout[] = {
+	[QPHY_SW_RESET]			= 0x00,
+	[QPHY_START_CTRL]		= 0x44,
+	[QPHY_PCS_STATUS]		= 0x14,
+};
+
 static const unsigned int sdm845_ufsphy_regs_layout[] = {
 	[QPHY_START_CTRL]		= 0x00,
 	[QPHY_PCS_READY_STATUS]		= 0x160,
@@ -972,6 +978,115 @@ enum qphy_reg_layout {
 	QMP_PHY_INIT_CFG(QPHY_V4_MULTI_LANE_CTRL1, 0x02),
 };
 
+static const struct qmp_phy_init_tbl sm8150_usb3_serdes_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_EN_CENTER, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_PER1, 0x31),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_PER2, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_STEP_SIZE1_MODE0, 0xde),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_STEP_SIZE2_MODE0, 0x07),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_STEP_SIZE1_MODE1, 0xde),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_STEP_SIZE2_MODE1, 0x07),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SYSCLK_BUF_ENABLE, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_CMN_IPTRIM, 0x20),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_CP_CTRL_MODE0, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_CP_CTRL_MODE1, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_PLL_RCTRL_MODE0, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_PLL_RCTRL_MODE1, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_PLL_CCTRL_MODE0, 0x36),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_PLL_CCTRL_MODE1, 0x36),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SYSCLK_EN_SEL, 0x1a),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_LOCK_CMP_EN, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_LOCK_CMP1_MODE0, 0x14),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_LOCK_CMP2_MODE0, 0x34),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_LOCK_CMP1_MODE1, 0x34),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_LOCK_CMP2_MODE1, 0x82),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_DEC_START_MODE0, 0x82),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_DEC_START_MODE1, 0x82),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_DIV_FRAC_START1_MODE0, 0xab),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_DIV_FRAC_START2_MODE0, 0xea),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_DIV_FRAC_START3_MODE0, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_VCO_TUNE_MAP, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_DIV_FRAC_START1_MODE1, 0xab),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_DIV_FRAC_START2_MODE1, 0xea),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_DIV_FRAC_START3_MODE1, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_VCO_TUNE1_MODE0, 0x24),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_VCO_TUNE1_MODE1, 0x24),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_VCO_TUNE2_MODE1, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_HSCLK_SEL, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_CORECLK_DIV_MODE1, 0x08),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_BIN_VCOCAL_CMP_CODE1_MODE0, 0xca),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_BIN_VCOCAL_CMP_CODE2_MODE0, 0x1e),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_BIN_VCOCAL_CMP_CODE1_MODE1, 0xca),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_BIN_VCOCAL_CMP_CODE2_MODE1, 0x1e),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_BIN_VCOCAL_HSCLK_SEL, 0x11),
+};
+
+static const struct qmp_phy_init_tbl sm8150_usb3_tx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_RES_CODE_LANE_TX, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_RES_CODE_LANE_RX, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_LANE_MODE_1, 0xd5),
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_RCV_DETECT_LVL_2, 0x12),
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_PI_QEC_CTRL, 0x20),
+};
+
+static const struct qmp_phy_init_tbl sm8150_usb3_rx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_GAIN, 0x05),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_FO_GAIN, 0x2f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x7f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_COUNT_LOW, 0xff),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_COUNT_HIGH, 0x0f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_PI_CONTROLS, 0x99),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_THRESH1, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_THRESH2, 0x08),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_GAIN1, 0x05),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_GAIN2, 0x05),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_VGA_CAL_CNTRL1, 0x54),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_VGA_CAL_CNTRL2, 0x0e),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL3, 0x4a),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL4, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_LOW, 0xc0),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_HIGH, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x77),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_CNTRL, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_DEGLITCH_CNTRL, 0x0e),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_LOW, 0xbf),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH, 0xbf),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH2, 0x3f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH3, 0x7f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH4, 0x94),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_LOW, 0xdc),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH, 0xdc),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH2, 0x5c),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH3, 0x0b),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH4, 0xb3),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_DFE_EN_TIMER, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_DFE_CTLE_POST_CAL_OFFSET, 0x38),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_AUX_DATA_TCOARSE_TFINE, 0xa0),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_DCC_CTRL1, 0x0c),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_GM_CAL, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_VTH_CODE, 0x10),
+};
+
+static const struct qmp_phy_init_tbl sm8150_usb3_pcs_tbl[] = {
+	/* Lock Det settings */
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG1, 0xd0),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG2, 0x07),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG6, 0x13),
+
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_REFGEN_REQ_CONFIG1, 0x21),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_RX_SIGDET_LVL, 0xaa),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_CDR_RESET_TIME, 0x0a),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_ALIGN_DETECT_CONFIG1, 0x88),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_ALIGN_DETECT_CONFIG2, 0x13),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_PCS_TX_RX_CONFIG, 0x0c),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_EQ_CONFIG1, 0x4b),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_EQ_CONFIG5, 0x10),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_USB3_LFPS_DET_HIGH_COUNT_VAL, 0xf8),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_USB3_RXEQTRAINING_DFE_TIME_S2, 0x07),
+};
+
+
 /* struct qmp_phy_cfg - per-PHY initialization config */
 struct qmp_phy_cfg {
 	/* phy-type - PCIE/UFS/USB */
@@ -1126,6 +1241,10 @@ static inline void qphy_clrbits(void __iomem *base, u32 offset, u32 val)
 	"aux", "cfg_ahb", "ref", "com_aux",
 };
 
+static const char * const qmp_v4_phy_clk_l[] = {
+	"aux", "ref_clk_src", "ref", "com_aux",
+};
+
 static const char * const sdm845_ufs_phy_clk_l[] = {
 	"ref", "ref_aux",
 };
@@ -1392,6 +1511,37 @@ static inline void qphy_clrbits(void __iomem *base, u32 offset, u32 val)
 	.is_dual_lane_phy	= true,
 };
 
+static const struct qmp_phy_cfg sm8150_usb3phy_cfg = {
+	.type			= PHY_TYPE_USB3,
+	.nlanes			= 1,
+
+	.serdes_tbl		= sm8150_usb3_serdes_tbl,
+	.serdes_tbl_num		= ARRAY_SIZE(sm8150_usb3_serdes_tbl),
+	.tx_tbl			= sm8150_usb3_tx_tbl,
+	.tx_tbl_num		= ARRAY_SIZE(sm8150_usb3_tx_tbl),
+	.rx_tbl			= sm8150_usb3_rx_tbl,
+	.rx_tbl_num		= ARRAY_SIZE(sm8150_usb3_rx_tbl),
+	.pcs_tbl		= sm8150_usb3_pcs_tbl,
+	.pcs_tbl_num		= ARRAY_SIZE(sm8150_usb3_pcs_tbl),
+	.clk_list		= qmp_v4_phy_clk_l,
+	.num_clks		= ARRAY_SIZE(qmp_v4_phy_clk_l),
+	.reset_list		= msm8996_usb3phy_reset_l,
+	.num_resets		= ARRAY_SIZE(msm8996_usb3phy_reset_l),
+	.vreg_list		= qmp_phy_vreg_l,
+	.num_vregs		= ARRAY_SIZE(qmp_phy_vreg_l),
+	.regs			= qmp_v4_usb3phy_regs_layout,
+
+	.start_ctrl		= SERDES_START | PCS_START,
+	.pwrdn_ctrl		= SW_PWRDN,
+
+	.has_pwrdn_delay	= true,
+	.pwrdn_delay_min	= POWER_DOWN_DELAY_US_MIN,
+	.pwrdn_delay_max	= POWER_DOWN_DELAY_US_MAX,
+
+	.has_phy_dp_com_ctrl	= true,
+	.is_dual_lane_phy	= true,
+};
+
 static void qcom_qmp_phy_configure(void __iomem *base,
 				   const unsigned int *regs,
 				   const struct qmp_phy_init_tbl tbl[],
@@ -2117,6 +2267,9 @@ int qcom_qmp_phy_create(struct device *dev, struct device_node *np, int id)
 	}, {
 		.compatible = "qcom,sm8150-qmp-ufs-phy",
 		.data = &sm8150_ufsphy_cfg,
+	}, {
+		.compatible = "qcom,sm8150-qmp-usb3-phy",
+		.data = &sm8150_usb3phy_cfg,
 	},
 	{ },
 };
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.h b/drivers/phy/qualcomm/phy-qcom-qmp.h
index 90f793c..22c9009 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.h
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.h
@@ -125,7 +125,7 @@
 #define QPHY_L1SS_WAKEUP_DLY_TIME_AUXCLK_LSB		0x1DC
 #define QPHY_L1SS_WAKEUP_DLY_TIME_AUXCLK_MSB		0x1E0
 
-/* Only for QMP V3 PHY - DP COM registers */
+/* Only for QMP V3 & V4 PHY - DP COM registers */
 #define QPHY_V3_DP_COM_PHY_MODE_CTRL			0x00
 #define QPHY_V3_DP_COM_SW_RESET				0x04
 #define QPHY_V3_DP_COM_POWER_DOWN_CTRL			0x08
@@ -314,6 +314,14 @@
 #define QPHY_V3_PCS_MISC_OSC_DTCT_MODE2_CONFIG5		0x60
 
 /* Only for QMP V4 PHY - QSERDES COM registers */
+#define QSERDES_V4_COM_SSC_EN_CENTER			0x010
+#define QSERDES_V4_COM_SSC_PER1				0x01c
+#define QSERDES_V4_COM_SSC_PER2				0x020
+#define QSERDES_V4_COM_SSC_STEP_SIZE1_MODE0		0x024
+#define QSERDES_V4_COM_SSC_STEP_SIZE2_MODE0		0x028
+#define QSERDES_V4_COM_SSC_STEP_SIZE1_MODE1		0x030
+#define QSERDES_V4_COM_SSC_STEP_SIZE2_MODE1		0x034
+#define QSERDES_V4_COM_SYSCLK_BUF_ENABLE		0x050
 #define QSERDES_V4_COM_PLL_IVCO				0x058
 #define QSERDES_V4_COM_CMN_IPTRIM			0x060
 #define QSERDES_V4_COM_CP_CTRL_MODE0			0x074
@@ -330,10 +338,22 @@
 #define QSERDES_V4_COM_DEC_START_MODE0			0x0bc
 #define QSERDES_V4_COM_LOCK_CMP2_MODE1			0x0b8
 #define QSERDES_V4_COM_DEC_START_MODE1			0x0c4
+#define QSERDES_V4_COM_DIV_FRAC_START1_MODE0		0x0cc
+#define QSERDES_V4_COM_DIV_FRAC_START2_MODE0		0x0d0
+#define QSERDES_V4_COM_DIV_FRAC_START3_MODE0		0x0d4
+#define QSERDES_V4_COM_DIV_FRAC_START1_MODE1		0x0d8
+#define QSERDES_V4_COM_DIV_FRAC_START2_MODE1		0x0dc
+#define QSERDES_V4_COM_DIV_FRAC_START3_MODE1		0x0e0
 #define QSERDES_V4_COM_VCO_TUNE_MAP			0x10c
+#define QSERDES_V4_COM_VCO_TUNE1_MODE0			0x110
+#define QSERDES_V4_COM_VCO_TUNE2_MODE0			0x114
+#define QSERDES_V4_COM_VCO_TUNE1_MODE1			0x118
+#define QSERDES_V4_COM_VCO_TUNE2_MODE1			0x11c
 #define QSERDES_V4_COM_VCO_TUNE_INITVAL2		0x124
 #define QSERDES_V4_COM_HSCLK_SEL			0x158
 #define QSERDES_V4_COM_HSCLK_HS_SWITCH_SEL		0x15c
+#define QSERDES_V4_COM_CORECLK_DIV_MODE1		0x16c
+#define QSERDES_V4_COM_SVS_MODE_CLK_SEL			0x184
 #define QSERDES_V4_COM_BIN_VCOCAL_CMP_CODE1_MODE0	0x1ac
 #define QSERDES_V4_COM_BIN_VCOCAL_CMP_CODE2_MODE0	0x1b0
 #define QSERDES_V4_COM_BIN_VCOCAL_CMP_CODE1_MODE1	0x1b4
@@ -341,12 +361,16 @@
 #define QSERDES_V4_COM_BIN_VCOCAL_CMP_CODE2_MODE1	0x1b8
 
 /* Only for QMP V4 PHY - TX registers */
+#define QSERDES_V4_TX_RES_CODE_LANE_TX			0x34
+#define QSERDES_V4_TX_RES_CODE_LANE_RX			0x38
 #define QSERDES_V4_TX_LANE_MODE_1			0x84
+#define QSERDES_V4_TX_RCV_DETECT_LVL_2			0x9c
 #define QSERDES_V4_TX_PWM_GEAR_1_DIVIDER_BAND0_1	0xd8
 #define QSERDES_V4_TX_PWM_GEAR_2_DIVIDER_BAND0_1	0xdC
 #define QSERDES_V4_TX_PWM_GEAR_3_DIVIDER_BAND0_1	0xe0
 #define QSERDES_V4_TX_PWM_GEAR_4_DIVIDER_BAND0_1	0xe4
 #define QSERDES_V4_TX_TRAN_DRVR_EMP_EN			0xb8
+#define QSERDES_V4_TX_PI_QEC_CTRL		0x104
 
 /* Only for QMP V4 PHY - RX registers */
 #define QSERDES_V4_RX_UCDR_FO_GAIN			0x008
@@ -354,17 +378,27 @@
 #define QSERDES_V4_RX_UCDR_FASTLOCK_FO_GAIN		0x030
 #define QSERDES_V4_RX_UCDR_SO_SATURATION_AND_ENABLE	0x034
 #define QSERDES_V4_RX_UCDR_FASTLOCK_COUNT_LOW		0x03c
+#define QSERDES_V4_RX_UCDR_FASTLOCK_COUNT_HIGH		0x040
 #define QSERDES_V4_RX_UCDR_PI_CONTROLS			0x044
 #define QSERDES_V4_RX_UCDR_PI_CTRL2			0x048
+#define QSERDES_V4_RX_UCDR_SB2_THRESH1			0x04c
+#define QSERDES_V4_RX_UCDR_SB2_THRESH2			0x050
+#define QSERDES_V4_RX_UCDR_SB2_GAIN1			0x054
+#define QSERDES_V4_RX_UCDR_SB2_GAIN2			0x058
+#define QSERDES_V4_RX_AUX_DATA_TCOARSE_TFINE			0x060
 #define QSERDES_V4_RX_AC_JTAG_ENABLE			0x068
 #define QSERDES_V4_RX_AC_JTAG_MODE			0x078
 #define QSERDES_V4_RX_RX_TERM_BW			0x080
+#define QSERDES_V4_RX_VGA_CAL_CNTRL1			0x0d4
+#define QSERDES_V4_RX_VGA_CAL_CNTRL2			0x0d8
+#define QSERDES_V4_RX_GM_CAL				0x0dc
 #define QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL2		0x0ec
 #define QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL3		0x0f0
 #define QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL4		0x0f4
 #define QSERDES_V4_RX_RX_IDAC_TSETTLE_LOW		0x0f8
 #define QSERDES_V4_RX_RX_IDAC_TSETTLE_HIGH		0x0fc
 #define QSERDES_V4_RX_RX_IDAC_MEASURE_TIME		0x100
+#define QSERDES_V4_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1	0x110
 #define QSERDES_V4_RX_RX_OFFSET_ADAPTOR_CNTRL2		0x114
 #define QSERDES_V4_RX_SIGDET_CNTRL			0x11c
 #define QSERDES_V4_RX_SIGDET_LVL			0x120
@@ -385,9 +419,12 @@
 #define QSERDES_V4_RX_RX_MODE_10_HIGH2			0x1a0
 #define QSERDES_V4_RX_RX_MODE_10_HIGH3			0x1a4
 #define QSERDES_V4_RX_RX_MODE_10_HIGH4			0x1a8
+#define QSERDES_V4_RX_DFE_EN_TIMER			0x1b4
+#define QSERDES_V4_RX_DFE_CTLE_POST_CAL_OFFSET		0x1b8
 #define QSERDES_V4_RX_DCC_CTRL1				0x1bc
+#define QSERDES_V4_RX_VTH_CODE				0x1c4
 
-/* Only for QMP V4 PHY - PCS registers */
+/* Only for QMP V4 PHY - UFS PCS registers */
 #define QPHY_V4_PHY_START				0x000
 #define QPHY_V4_POWER_DOWN_CONTROL			0x004
 #define QPHY_V4_SW_RESET				0x008
@@ -409,4 +446,161 @@
 #define QPHY_V4_TX_MID_TERM_CTRL1			0x1d8
 #define QPHY_V4_MULTI_LANE_CTRL1			0x1e0
 
+/* Only for QMP V4 PHY - USB/PCIe PCS registers */
+#define QPHY_V4_PCS_SW_RESET				0x000
+#define QPHY_V4_PCS_REVISION_ID0			0x004
+#define QPHY_V4_PCS_REVISION_ID1			0x008
+#define QPHY_V4_PCS_REVISION_ID2			0x00c
+#define QPHY_V4_PCS_REVISION_ID3			0x010
+#define QPHY_V4_PCS_PCS_STATUS1				0x014
+#define QPHY_V4_PCS_PCS_STATUS2				0x018
+#define QPHY_V4_PCS_PCS_STATUS3				0x01c
+#define QPHY_V4_PCS_PCS_STATUS4				0x020
+#define QPHY_V4_PCS_PCS_STATUS5				0x024
+#define QPHY_V4_PCS_PCS_STATUS6				0x028
+#define QPHY_V4_PCS_PCS_STATUS7				0x02c
+#define QPHY_V4_PCS_DEBUG_BUS_0_STATUS			0x030
+#define QPHY_V4_PCS_DEBUG_BUS_1_STATUS			0x034
+#define QPHY_V4_PCS_DEBUG_BUS_2_STATUS			0x038
+#define QPHY_V4_PCS_DEBUG_BUS_3_STATUS			0x03c
+#define QPHY_V4_PCS_POWER_DOWN_CONTROL			0x040
+#define QPHY_V4_PCS_START_CONTROL			0x044
+#define QPHY_V4_PCS_INSIG_SW_CTRL1			0x048
+#define QPHY_V4_PCS_INSIG_SW_CTRL2			0x04c
+#define QPHY_V4_PCS_INSIG_SW_CTRL3			0x050
+#define QPHY_V4_PCS_INSIG_SW_CTRL4			0x054
+#define QPHY_V4_PCS_INSIG_SW_CTRL5			0x058
+#define QPHY_V4_PCS_INSIG_SW_CTRL6			0x05c
+#define QPHY_V4_PCS_INSIG_SW_CTRL7			0x060
+#define QPHY_V4_PCS_INSIG_SW_CTRL8			0x064
+#define QPHY_V4_PCS_INSIG_MX_CTRL1			0x068
+#define QPHY_V4_PCS_INSIG_MX_CTRL2			0x06c
+#define QPHY_V4_PCS_INSIG_MX_CTRL3			0x070
+#define QPHY_V4_PCS_INSIG_MX_CTRL4			0x074
+#define QPHY_V4_PCS_INSIG_MX_CTRL5			0x078
+#define QPHY_V4_PCS_INSIG_MX_CTRL7			0x07c
+#define QPHY_V4_PCS_INSIG_MX_CTRL8			0x080
+#define QPHY_V4_PCS_OUTSIG_SW_CTRL1			0x084
+#define QPHY_V4_PCS_OUTSIG_MX_CTRL1			0x088
+#define QPHY_V4_PCS_CLAMP_ENABLE			0x08c
+#define QPHY_V4_PCS_POWER_STATE_CONFIG1			0x090
+#define QPHY_V4_PCS_POWER_STATE_CONFIG2			0x094
+#define QPHY_V4_PCS_FLL_CNTRL1				0x098
+#define QPHY_V4_PCS_FLL_CNTRL2				0x09c
+#define QPHY_V4_PCS_FLL_CNT_VAL_L			0x0a0
+#define QPHY_V4_PCS_FLL_CNT_VAL_H_TOL			0x0a4
+#define QPHY_V4_PCS_FLL_MAN_CODE			0x0a8
+#define QPHY_V4_PCS_TEST_CONTROL1			0x0ac
+#define QPHY_V4_PCS_TEST_CONTROL2			0x0b0
+#define QPHY_V4_PCS_TEST_CONTROL3			0x0b4
+#define QPHY_V4_PCS_TEST_CONTROL4			0x0b8
+#define QPHY_V4_PCS_TEST_CONTROL5			0x0bc
+#define QPHY_V4_PCS_TEST_CONTROL6			0x0c0
+#define QPHY_V4_PCS_LOCK_DETECT_CONFIG1			0x0c4
+#define QPHY_V4_PCS_LOCK_DETECT_CONFIG2			0x0c8
+#define QPHY_V4_PCS_LOCK_DETECT_CONFIG3			0x0cc
+#define QPHY_V4_PCS_LOCK_DETECT_CONFIG4			0x0d0
+#define QPHY_V4_PCS_LOCK_DETECT_CONFIG5			0x0d4
+#define QPHY_V4_PCS_LOCK_DETECT_CONFIG6			0x0d8
+#define QPHY_V4_PCS_REFGEN_REQ_CONFIG1			0x0dc
+#define QPHY_V4_PCS_REFGEN_REQ_CONFIG2			0x0e0
+#define QPHY_V4_PCS_REFGEN_REQ_CONFIG3			0x0e4
+#define QPHY_V4_PCS_BIST_CTRL				0x0e8
+#define QPHY_V4_PCS_PRBS_POLY0				0x0ec
+#define QPHY_V4_PCS_PRBS_POLY1				0x0f0
+#define QPHY_V4_PCS_FIXED_PAT0				0x0f4
+#define QPHY_V4_PCS_FIXED_PAT1				0x0f8
+#define QPHY_V4_PCS_FIXED_PAT2				0x0fc
+#define QPHY_V4_PCS_FIXED_PAT3				0x100
+#define QPHY_V4_PCS_FIXED_PAT4				0x104
+#define QPHY_V4_PCS_FIXED_PAT5				0x108
+#define QPHY_V4_PCS_FIXED_PAT6				0x10c
+#define QPHY_V4_PCS_FIXED_PAT7				0x110
+#define QPHY_V4_PCS_FIXED_PAT8				0x114
+#define QPHY_V4_PCS_FIXED_PAT9				0x118
+#define QPHY_V4_PCS_FIXED_PAT10				0x11c
+#define QPHY_V4_PCS_FIXED_PAT11				0x120
+#define QPHY_V4_PCS_FIXED_PAT12				0x124
+#define QPHY_V4_PCS_FIXED_PAT13				0x128
+#define QPHY_V4_PCS_FIXED_PAT14				0x12c
+#define QPHY_V4_PCS_FIXED_PAT15				0x130
+#define QPHY_V4_PCS_TXMGN_CONFIG			0x134
+#define QPHY_V4_PCS_G12S1_TXMGN_V0			0x138
+#define QPHY_V4_PCS_G12S1_TXMGN_V1			0x13c
+#define QPHY_V4_PCS_G12S1_TXMGN_V2			0x140
+#define QPHY_V4_PCS_G12S1_TXMGN_V3			0x144
+#define QPHY_V4_PCS_G12S1_TXMGN_V4			0x148
+#define QPHY_V4_PCS_G12S1_TXMGN_V0_RS			0x14c
+#define QPHY_V4_PCS_G12S1_TXMGN_V1_RS			0x150
+#define QPHY_V4_PCS_G12S1_TXMGN_V2_RS			0x154
+#define QPHY_V4_PCS_G12S1_TXMGN_V3_RS			0x158
+#define QPHY_V4_PCS_G12S1_TXMGN_V4_RS			0x15c
+#define QPHY_V4_PCS_G3S2_TXMGN_MAIN			0x160
+#define QPHY_V4_PCS_G3S2_TXMGN_MAIN_RS			0x164
+#define QPHY_V4_PCS_G12S1_TXDEEMPH_M6DB			0x168
+#define QPHY_V4_PCS_G12S1_TXDEEMPH_M3P5DB		0x16c
+#define QPHY_V4_PCS_G3S2_PRE_GAIN			0x170
+#define QPHY_V4_PCS_G3S2_POST_GAIN			0x174
+#define QPHY_V4_PCS_G3S2_PRE_POST_OFFSET		0x178
+#define QPHY_V4_PCS_G3S2_PRE_GAIN_RS			0x17c
+#define QPHY_V4_PCS_G3S2_POST_GAIN_RS			0x180
+#define QPHY_V4_PCS_G3S2_PRE_POST_OFFSET_RS		0x184
+#define QPHY_V4_PCS_RX_SIGDET_LVL			0x188
+#define QPHY_V4_PCS_RX_SIGDET_DTCT_CNTRL		0x18c
+#define QPHY_V4_PCS_RCVR_DTCT_DLY_P1U2_L		0x190
+#define QPHY_V4_PCS_RCVR_DTCT_DLY_P1U2_H		0x194
+#define QPHY_V4_PCS_RATE_SLEW_CNTRL1			0x198
+#define QPHY_V4_PCS_RATE_SLEW_CNTRL2			0x19c
+#define QPHY_V4_PCS_PWRUP_RESET_DLY_TIME_AUXCLK		0x1a0
+#define QPHY_V4_PCS_P2U3_WAKEUP_DLY_TIME_AUXCLK_L	0x1a4
+#define QPHY_V4_PCS_P2U3_WAKEUP_DLY_TIME_AUXCLK_H	0x1a8
+#define QPHY_V4_PCS_TSYNC_RSYNC_TIME			0x1ac
+#define QPHY_V4_PCS_CDR_RESET_TIME			0x1b0
+#define QPHY_V4_PCS_TSYNC_DLY_TIME			0x1b4
+#define QPHY_V4_PCS_ELECIDLE_DLY_SEL			0x1b8
+#define QPHY_V4_PCS_CMN_ACK_OUT_SEL			0x1bc
+#define QPHY_V4_PCS_ALIGN_DETECT_CONFIG1		0x1c0
+#define QPHY_V4_PCS_ALIGN_DETECT_CONFIG2		0x1c4
+#define QPHY_V4_PCS_ALIGN_DETECT_CONFIG3		0x1c8
+#define QPHY_V4_PCS_ALIGN_DETECT_CONFIG4		0x1cc
+#define QPHY_V4_PCS_PCS_TX_RX_CONFIG			0x1d0
+#define QPHY_V4_PCS_RX_IDLE_DTCT_CNTRL			0x1d4
+#define QPHY_V4_PCS_RX_DCC_CAL_CONFIG			0x1d8
+#define QPHY_V4_PCS_EQ_CONFIG1				0x1dc
+#define QPHY_V4_PCS_EQ_CONFIG2				0x1e0
+#define QPHY_V4_PCS_EQ_CONFIG3				0x1e4
+#define QPHY_V4_PCS_EQ_CONFIG4				0x1e8
+#define QPHY_V4_PCS_EQ_CONFIG5				0x1ec
+#define QPHY_V4_PCS_USB3_POWER_STATE_CONFIG1		0x300
+#define QPHY_V4_PCS_USB3_AUTONOMOUS_MODE_STATUS		0x304
+#define QPHY_V4_PCS_USB3_AUTONOMOUS_MODE_CTRL		0x308
+#define QPHY_V4_PCS_USB3_AUTONOMOUS_MODE_CTRL2		0x30c
+#define QPHY_V4_PCS_USB3_LFPS_RXTERM_IRQ_SOURCE_STATUS	0x310
+#define QPHY_V4_PCS_USB3_LFPS_RXTERM_IRQ_CLEAR		0x314
+#define QPHY_V4_PCS_USB3_LFPS_DET_HIGH_COUNT_VAL	0x318
+#define QPHY_V4_PCS_USB3_LFPS_TX_ECSTART		0x31c
+#define QPHY_V4_PCS_USB3_LFPS_PER_TIMER_VAL		0x320
+#define QPHY_V4_PCS_USB3_LFPS_TX_END_CNT_U3_START	0x324
+#define QPHY_V4_PCS_USB3_RXEQTRAINING_LOCK_TIME		0x328
+#define QPHY_V4_PCS_USB3_RXEQTRAINING_WAIT_TIME		0x32c
+#define QPHY_V4_PCS_USB3_RXEQTRAINING_CTLE_TIME		0x330
+#define QPHY_V4_PCS_USB3_RXEQTRAINING_WAIT_TIME_S2	0x334
+#define QPHY_V4_PCS_USB3_RXEQTRAINING_DFE_TIME_S2	0x338
+#define QPHY_V4_PCS_USB3_RCVR_DTCT_DLY_U3_L		0x33c
+#define QPHY_V4_PCS_USB3_RCVR_DTCT_DLY_U3_H		0x340
+#define QPHY_V4_PCS_USB3_ARCVR_DTCT_EN_PERIOD		0x344
+#define QPHY_V4_PCS_USB3_ARCVR_DTCT_CM_DLY		0x348
+#define QPHY_V4_PCS_USB3_TXONESZEROS_RUN_LENGTH		0x34c
+#define QPHY_V4_PCS_USB3_ALFPS_DEGLITCH_VAL		0x350
+#define QPHY_V4_PCS_USB3_SIGDET_STARTUP_TIMER_VAL	0x354
+#define QPHY_V4_PCS_USB3_TEST_CONTROL			0x358
+
+/* Only for QMP V4 PHY - PCS_MISC registers */
+#define QPHY_V4_PCS_MISC_TYPEC_CTRL			0x00
+#define QPHY_V4_PCS_MISC_TYPEC_PWRDN_CTRL		0x04
+#define QPHY_V4_PCS_MISC_PCS_MISC_CONFIG1		0x08
+#define QPHY_V4_PCS_MISC_CLAMP_ENABLE			0x0c
+#define QPHY_V4_PCS_MISC_TYPEC_STATUS			0x10
+#define QPHY_V4_PCS_MISC_PLACEHOLDER_STATUS		0x14
+
 #endif
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

^ permalink raw reply	[flat|nested] 6+ messages in thread

* [PATCH v3 4/4] phy: qcom-qmp: Use proper PWRDOWN offset for sm8150 USB
  2020-03-25 17:43 [PATCH v3 0/4] Add SS/HS-USB changes for Qualcomm SM8150 chipset Wesley Cheng
                   ` (2 preceding siblings ...)
  2020-03-25 17:43 ` [PATCH v3 3/4] phy: qcom-qmp: Add SM8150 QMP USB3 PHY support Wesley Cheng
@ 2020-03-25 17:43 ` Wesley Cheng
  2020-03-27  0:32   ` Wesley Cheng
  3 siblings, 1 reply; 6+ messages in thread
From: Wesley Cheng @ 2020-03-25 17:43 UTC (permalink / raw)
  To: agross, bjorn.andersson, kishon, robh+dt, mark.rutland, p.zabel
  Cc: linux-arm-msm, linux-kernel, devicetree, Wesley Cheng

The register map for SM8150 QMP USB SSPHY has moved
QPHY_POWER_DOWN_CONTROL to a different offset.  Allow for
an offset in the register table to override default value
if it is a DP capable PHY.

Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
---
 drivers/phy/qualcomm/phy-qcom-qmp.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
index cc04471..71a230a 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
@@ -164,6 +164,7 @@ enum qphy_reg_layout {
 	[QPHY_SW_RESET]			= 0x00,
 	[QPHY_START_CTRL]		= 0x44,
 	[QPHY_PCS_STATUS]		= 0x14,
+	[QPHY_COM_POWER_DOWN_CONTROL]	= 0x40,
 };
 
 static const unsigned int sdm845_ufsphy_regs_layout[] = {
@@ -1627,6 +1628,9 @@ static int qcom_qmp_phy_com_init(struct qmp_phy *qphy)
 	if (cfg->has_phy_com_ctrl)
 		qphy_setbits(serdes, cfg->regs[QPHY_COM_POWER_DOWN_CONTROL],
 			     SW_PWRDN);
+	else if (!cfg->has_phy_com_ctrl && cfg->regs[QPHY_COM_POWER_DOWN_CONTROL])
+		qphy_setbits(pcs, cfg->regs[QPHY_COM_POWER_DOWN_CONTROL],
+			     cfg->pwrdn_ctrl);
 	else
 		qphy_setbits(pcs, QPHY_POWER_DOWN_CONTROL, cfg->pwrdn_ctrl);
 
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [PATCH v3 4/4] phy: qcom-qmp: Use proper PWRDOWN offset for sm8150 USB
  2020-03-25 17:43 ` [PATCH v3 4/4] phy: qcom-qmp: Use proper PWRDOWN offset for sm8150 USB Wesley Cheng
@ 2020-03-27  0:32   ` Wesley Cheng
  0 siblings, 0 replies; 6+ messages in thread
From: Wesley Cheng @ 2020-03-27  0:32 UTC (permalink / raw)
  To: agross, bjorn.andersson, kishon, robh+dt, mark.rutland, p.zabel
  Cc: linux-arm-msm, linux-kernel, devicetree



On 3/25/2020 10:43 AM, Wesley Cheng wrote:
> The register map for SM8150 QMP USB SSPHY has moved
> QPHY_POWER_DOWN_CONTROL to a different offset.  Allow for
> an offset in the register table to override default value
> if it is a DP capable PHY.
> 
> Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
> ---
>  drivers/phy/qualcomm/phy-qcom-qmp.c | 4 ++++
>  1 file changed, 4 insertions(+)
> 
> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
> index cc04471..71a230a 100644
> --- a/drivers/phy/qualcomm/phy-qcom-qmp.c
> +++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
> @@ -164,6 +164,7 @@ enum qphy_reg_layout {
>  	[QPHY_SW_RESET]			= 0x00,
>  	[QPHY_START_CTRL]		= 0x44,
>  	[QPHY_PCS_STATUS]		= 0x14,
> +	[QPHY_COM_POWER_DOWN_CONTROL]	= 0x40,
>  };
>  
>  static const unsigned int sdm845_ufsphy_regs_layout[] = {
> @@ -1627,6 +1628,9 @@ static int qcom_qmp_phy_com_init(struct qmp_phy *qphy)
>  	if (cfg->has_phy_com_ctrl)
>  		qphy_setbits(serdes, cfg->regs[QPHY_COM_POWER_DOWN_CONTROL],
>  			     SW_PWRDN);
> +	else if (!cfg->has_phy_com_ctrl && cfg->regs[QPHY_COM_POWER_DOWN_CONTROL])
> +		qphy_setbits(pcs, cfg->regs[QPHY_COM_POWER_DOWN_CONTROL],
> +			     cfg->pwrdn_ctrl);
>  	else
>  		qphy_setbits(pcs, QPHY_POWER_DOWN_CONTROL, cfg->pwrdn_ctrl);
>  
> 

Will add logic to the qcom_qmp_phy_com_exit() API as well to fix the
power down offset if DP com is being used, and will check for
has_phy_dp_com_ctrl instead of !has_phy_com_ctrl, as to ensure this only
applies to PHYs that have DP COM.

-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

^ permalink raw reply	[flat|nested] 6+ messages in thread

end of thread, back to index

Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-03-25 17:43 [PATCH v3 0/4] Add SS/HS-USB changes for Qualcomm SM8150 chipset Wesley Cheng
2020-03-25 17:43 ` [PATCH v3 1/4] dt-bindings: phy: Add binding for qcom,usb-hs-7nm Wesley Cheng
2020-03-25 17:43 ` [PATCH v3 2/4] phy: qcom-snps: Add SNPS USB PHY driver for QCOM based SOCs Wesley Cheng
2020-03-25 17:43 ` [PATCH v3 3/4] phy: qcom-qmp: Add SM8150 QMP USB3 PHY support Wesley Cheng
2020-03-25 17:43 ` [PATCH v3 4/4] phy: qcom-qmp: Use proper PWRDOWN offset for sm8150 USB Wesley Cheng
2020-03-27  0:32   ` Wesley Cheng

Linux-ARM-MSM Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-arm-msm/0 linux-arm-msm/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-arm-msm linux-arm-msm/ https://lore.kernel.org/linux-arm-msm \
		linux-arm-msm@vger.kernel.org
	public-inbox-index linux-arm-msm

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-arm-msm


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git