From: satya priya <skakit@codeaurora.org>
To: Andy Gross <agross@kernel.org>,
Bjorn Andersson <bjorn.andersson@linaro.org>,
Rob Herring <robh+dt@kernel.org>
Cc: mka@chromium.org, linux-arm-msm@vger.kernel.org,
linux-kernel@vger.kernel.org, devicetree@vger.kernel.org,
kgunda@codeaurora.org, satya priya <skakit@codeaurora.org>
Subject: [PATCH V4 3/8] arm64: dts: qcom: pm7325: Add pm7325 base dts file
Date: Wed, 5 May 2021 12:25:21 +0530 [thread overview]
Message-ID: <1620197726-23802-4-git-send-email-skakit@codeaurora.org> (raw)
In-Reply-To: <1620197726-23802-1-git-send-email-skakit@codeaurora.org>
Add base DTS file for pm7325 along with GPIOs and temp-alarm nodes.
Signed-off-by: satya priya <skakit@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
---
arch/arm64/boot/dts/qcom/pm7325.dtsi | 53 ++++++++++++++++++++++++++++++++++++
1 file changed, 53 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/pm7325.dtsi
diff --git a/arch/arm64/boot/dts/qcom/pm7325.dtsi b/arch/arm64/boot/dts/qcom/pm7325.dtsi
new file mode 100644
index 0000000..e7f64a9
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pm7325.dtsi
@@ -0,0 +1,53 @@
+// SPDX-License-Identifier: BSD-3-Clause
+// Copyright (c) 2021, The Linux Foundation. All rights reserved.
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+&spmi_bus {
+ pm7325: pmic@1 {
+ compatible = "qcom,pm7325", "qcom,spmi-pmic";
+ reg = <0x1 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm7325_temp_alarm: temp-alarm@a00 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0xa00>;
+ interrupts = <0x1 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ pm7325_gpios: gpios@8800 {
+ compatible = "qcom,pm7325-gpio", "qcom,spmi-gpio";
+ reg = <0x8800>;
+ gpio-controller;
+ gpio-ranges = <&pm7325_gpios 0 0 10>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+};
+
+&thermal_zones {
+ pm7325_thermal: pm7325-thermal {
+ polling-delay-passive = <100>;
+ polling-delay = <0>;
+ thermal-sensors = <&pm7325_temp_alarm>;
+
+ trips {
+ pm7325_trip0: trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ pm7325_crit: pm7325-crit {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+ };
+};
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
next prev parent reply other threads:[~2021-05-05 6:56 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-05-05 6:55 [PATCH V4 0/8] Add PMIC DT files for sc7280 satya priya
2021-05-05 6:55 ` [PATCH V4 1/8] arm64: dts: qcom: sm8350: Add label for thermal-zones node satya priya
2021-05-05 13:33 ` Matthias Kaehlcke
2021-05-05 6:55 ` [PATCH V4 2/8] arm64: dts: qcom: sc7280: Add " satya priya
2021-05-05 13:41 ` Matthias Kaehlcke
2021-05-05 6:55 ` satya priya [this message]
2021-05-05 6:55 ` [PATCH V4 4/8] arm64: dts: qcom: pm8350c: Add temp-alarm support satya priya
2021-05-05 6:55 ` [PATCH V4 5/8] arm64: dts: qcom: pmr735a: " satya priya
2021-05-05 6:55 ` [PATCH V4 6/8] arm64: dts: qcom: pmk8350: Add peripherals for pmk8350 satya priya
2021-05-05 14:35 ` Matthias Kaehlcke
2021-05-05 6:55 ` [PATCH V4 7/8] arm64: dts: qcom: sc7280: Add channel nodes for sc7280-idp satya priya
2021-05-05 14:46 ` Matthias Kaehlcke
2021-05-17 5:28 ` skakit
2021-05-05 6:55 ` [PATCH V4 8/8] arm64: dts: qcom: sc7280: Include PMIC DT files " satya priya
2021-05-05 14:57 ` Matthias Kaehlcke
2021-05-17 5:27 ` skakit
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1620197726-23802-4-git-send-email-skakit@codeaurora.org \
--to=skakit@codeaurora.org \
--cc=agross@kernel.org \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=kgunda@codeaurora.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mka@chromium.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).