linux-arm-msm.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
* [PATCH v6 1/2] drm/msm/dp: handle irq_hpd with sink_count = 0 correctly
@ 2021-05-19 20:22 Kuogee Hsieh
  2021-05-21 21:56 ` Stephen Boyd
  0 siblings, 1 reply; 4+ messages in thread
From: Kuogee Hsieh @ 2021-05-19 20:22 UTC (permalink / raw)
  To: robdclark, sean, swboyd, vkoul, agross, bjorn.andersson
  Cc: abhinavk, aravindh, khsieh, linux-arm-msm, linux-kernel

irq_hpd interrupt should be handled after dongle plugged in and
before dongle unplugged. Hence irq_hpd interrupt is enabled at
the end of the plugin handle and disabled at the beginning of
unplugged handle. Current irq_hpd with sink_count = 0 is wrongly
handled same as the dongle unplugged which tears down the mainlink
and disables the phy. This patch fixes this problem by only tearing
down the mainlink but keeping phy enabled at irq_hpd with
sink_count = 0 handle so that next irq_hpd with sink_count =1 can be
handled by setup mainlink only. This patch also set dongle into D3
(power off) state at end of handling irq_hpd with sink_count = 0.

Changes in v2:
-- add ctrl->phy_Power_count

Changes in v3:
-- del ctrl->phy_Power_count
-- add phy_power_off to dp_ctrl_off_link_stream()

Changes in v4:
-- return immediately if clock disable failed at dp_ctrl_off_link_stream()

Changes in v5:
-- set dongle to D3 (power off) state at dp_ctrl_off_link_stream()

Changes in v6:
-- add Fixes tag

Fixes: 94e58e2d06e3 ("drm/msm/dp: reset dp controller only at boot up and pm_resume")

Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
---
 drivers/gpu/drm/msm/dp/dp_catalog.c |  5 ++--
 drivers/gpu/drm/msm/dp/dp_ctrl.c    | 55 +++++++++++++++++++++++++++++++++++
 drivers/gpu/drm/msm/dp/dp_ctrl.h    |  2 ++
 drivers/gpu/drm/msm/dp/dp_display.c | 57 +++++++++++++++++++++++++++----------
 4 files changed, 101 insertions(+), 18 deletions(-)

diff --git a/drivers/gpu/drm/msm/dp/dp_catalog.c b/drivers/gpu/drm/msm/dp/dp_catalog.c
index b1a9b1b..f4f53f2 100644
--- a/drivers/gpu/drm/msm/dp/dp_catalog.c
+++ b/drivers/gpu/drm/msm/dp/dp_catalog.c
@@ -582,10 +582,9 @@ void dp_catalog_ctrl_hpd_config(struct dp_catalog *dp_catalog)
 
 	u32 reftimer = dp_read_aux(catalog, REG_DP_DP_HPD_REFTIMER);
 
-	/* enable HPD interrupts */
+	/* enable HPD plug and unplug interrupts */
 	dp_catalog_hpd_config_intr(dp_catalog,
-		DP_DP_HPD_PLUG_INT_MASK | DP_DP_IRQ_HPD_INT_MASK
-		| DP_DP_HPD_UNPLUG_INT_MASK | DP_DP_HPD_REPLUG_INT_MASK, true);
+		DP_DP_HPD_PLUG_INT_MASK | DP_DP_HPD_UNPLUG_INT_MASK, true);
 
 	/* Configure REFTIMER and enable it */
 	reftimer |= DP_DP_HPD_REFTIMER_ENABLE;
diff --git a/drivers/gpu/drm/msm/dp/dp_ctrl.c b/drivers/gpu/drm/msm/dp/dp_ctrl.c
index 8d59eb9..dbd8943 100644
--- a/drivers/gpu/drm/msm/dp/dp_ctrl.c
+++ b/drivers/gpu/drm/msm/dp/dp_ctrl.c
@@ -1811,6 +1811,61 @@ int dp_ctrl_on_stream(struct dp_ctrl *dp_ctrl)
 	return ret;
 }
 
+int dp_ctrl_off_link_stream(struct dp_ctrl *dp_ctrl)
+{
+	struct dp_ctrl_private *ctrl;
+	struct dp_io *dp_io;
+	struct phy *phy;
+	int ret;
+
+	ctrl = container_of(dp_ctrl, struct dp_ctrl_private, dp_ctrl);
+	dp_io = &ctrl->parser->io;
+	phy = dp_io->phy;
+
+	/* set dongle to D3 (power off) mode */
+	dp_link_psm_config(ctrl->link, &ctrl->panel->link_info, true);
+
+	dp_catalog_ctrl_mainlink_ctrl(ctrl->catalog, false);
+
+	ret = dp_power_clk_enable(ctrl->power, DP_STREAM_PM, false);
+	if (ret) {
+		DRM_ERROR("Failed to disable pixel clocks. ret=%d\n", ret);
+		return ret;
+	}
+
+	ret = dp_power_clk_enable(ctrl->power, DP_CTRL_PM, false);
+	if (ret) {
+		DRM_ERROR("Failed to disable link clocks. ret=%d\n", ret);
+		return ret;
+	}
+
+	phy_power_off(phy);
+
+	/* aux channel down, reinit phy */
+	phy_exit(phy);
+	phy_init(phy);
+
+	DRM_DEBUG_DP("DP off link/stream done\n");
+	return ret;
+}
+
+void dp_ctrl_off_phy(struct dp_ctrl *dp_ctrl)
+{
+	struct dp_ctrl_private *ctrl;
+	struct dp_io *dp_io;
+	struct phy *phy;
+
+	ctrl = container_of(dp_ctrl, struct dp_ctrl_private, dp_ctrl);
+	dp_io = &ctrl->parser->io;
+	phy = dp_io->phy;
+
+	dp_catalog_ctrl_reset(ctrl->catalog);
+
+	phy_exit(phy);
+
+	DRM_DEBUG_DP("DP off phy done\n");
+}
+
 int dp_ctrl_off(struct dp_ctrl *dp_ctrl)
 {
 	struct dp_ctrl_private *ctrl;
diff --git a/drivers/gpu/drm/msm/dp/dp_ctrl.h b/drivers/gpu/drm/msm/dp/dp_ctrl.h
index a836bd3..25e4f75 100644
--- a/drivers/gpu/drm/msm/dp/dp_ctrl.h
+++ b/drivers/gpu/drm/msm/dp/dp_ctrl.h
@@ -23,6 +23,8 @@ int dp_ctrl_host_init(struct dp_ctrl *dp_ctrl, bool flip, bool reset);
 void dp_ctrl_host_deinit(struct dp_ctrl *dp_ctrl);
 int dp_ctrl_on_link(struct dp_ctrl *dp_ctrl);
 int dp_ctrl_on_stream(struct dp_ctrl *dp_ctrl);
+int dp_ctrl_off_link_stream(struct dp_ctrl *dp_ctrl);
+void dp_ctrl_off_phy(struct dp_ctrl *dp_ctrl);
 int dp_ctrl_off(struct dp_ctrl *dp_ctrl);
 void dp_ctrl_push_idle(struct dp_ctrl *dp_ctrl);
 void dp_ctrl_isr(struct dp_ctrl *dp_ctrl);
diff --git a/drivers/gpu/drm/msm/dp/dp_display.c b/drivers/gpu/drm/msm/dp/dp_display.c
index 0ba71c7..b2a282a 100644
--- a/drivers/gpu/drm/msm/dp/dp_display.c
+++ b/drivers/gpu/drm/msm/dp/dp_display.c
@@ -337,6 +337,12 @@ static int dp_display_process_hpd_high(struct dp_display_private *dp)
 	dp->dp_display.max_pclk_khz = DP_MAX_PIXEL_CLK_KHZ;
 	dp->dp_display.max_dp_lanes = dp->parser->max_dp_lanes;
 
+	/*
+	 * set sink to normal operation mode -- D0
+	 * before dpcd read
+	 */
+	dp_link_psm_config(dp->link, &dp->panel->link_info, false);
+
 	dp_link_reset_phy_params_vx_px(dp->link);
 	rc = dp_ctrl_on_link(dp->ctrl);
 	if (rc) {
@@ -405,11 +411,6 @@ static int dp_display_usbpd_configure_cb(struct device *dev)
 
 	dp_display_host_init(dp, false);
 
-	/*
-	 * set sink to normal operation mode -- D0
-	 * before dpcd read
-	 */
-	dp_link_psm_config(dp->link, &dp->panel->link_info, false);
 	rc = dp_display_process_hpd_high(dp);
 end:
 	return rc;
@@ -570,6 +571,10 @@ static int dp_hpd_plug_handle(struct dp_display_private *dp, u32 data)
 		dp_add_event(dp, EV_CONNECT_PENDING_TIMEOUT, 0, tout);
 	}
 
+	/* enable HDP irq_hpd/replug interrupt */
+	dp_catalog_hpd_config_intr(dp->catalog,
+		DP_DP_IRQ_HPD_INT_MASK | DP_DP_HPD_REPLUG_INT_MASK, true);
+
 	mutex_unlock(&dp->event_mutex);
 
 	/* uevent will complete connection part */
@@ -619,7 +624,26 @@ static int dp_hpd_unplug_handle(struct dp_display_private *dp, u32 data)
 	mutex_lock(&dp->event_mutex);
 
 	state = dp->hpd_state;
-	if (state == ST_DISCONNECT_PENDING || state == ST_DISCONNECTED) {
+
+	/* disable irq_hpd/replug interrupts */
+	dp_catalog_hpd_config_intr(dp->catalog,
+		DP_DP_IRQ_HPD_INT_MASK | DP_DP_HPD_REPLUG_INT_MASK, false);
+
+	/* unplugged, no more irq_hpd handle */
+	dp_del_event(dp, EV_IRQ_HPD_INT);
+
+	if (state == ST_DISCONNECTED) {
+		/* triggered by irq_hdp with sink_count = 0 */
+		if (dp->link->sink_count == 0) {
+			dp_ctrl_off_phy(dp->ctrl);
+			hpd->hpd_high = 0;
+			dp->core_initialized = false;
+		}
+		mutex_unlock(&dp->event_mutex);
+		return 0;
+	}
+
+	if (state == ST_DISCONNECT_PENDING) {
 		mutex_unlock(&dp->event_mutex);
 		return 0;
 	}
@@ -633,9 +657,8 @@ static int dp_hpd_unplug_handle(struct dp_display_private *dp, u32 data)
 
 	dp->hpd_state = ST_DISCONNECT_PENDING;
 
-	/* disable HPD plug interrupt until disconnect is done */
-	dp_catalog_hpd_config_intr(dp->catalog, DP_DP_HPD_PLUG_INT_MASK
-				| DP_DP_IRQ_HPD_INT_MASK, false);
+	/* disable HPD plug interrupts */
+	dp_catalog_hpd_config_intr(dp->catalog, DP_DP_HPD_PLUG_INT_MASK, false);
 
 	hpd->hpd_high = 0;
 
@@ -652,8 +675,8 @@ static int dp_hpd_unplug_handle(struct dp_display_private *dp, u32 data)
 	reinit_completion(&dp->audio_comp);
 	dp_display_handle_plugged_change(g_dp_display, false);
 
-	dp_catalog_hpd_config_intr(dp->catalog, DP_DP_HPD_PLUG_INT_MASK |
-					DP_DP_IRQ_HPD_INT_MASK, true);
+	/* enable HDP plug interrupt to prepare for next plugin */
+	dp_catalog_hpd_config_intr(dp->catalog, DP_DP_HPD_PLUG_INT_MASK, true);
 
 	/* uevent will complete disconnection part */
 	mutex_unlock(&dp->event_mutex);
@@ -684,7 +707,7 @@ static int dp_irq_hpd_handle(struct dp_display_private *dp, u32 data)
 
 	/* irq_hpd can happen at either connected or disconnected state */
 	state =  dp->hpd_state;
-	if (state == ST_DISPLAY_OFF) {
+	if (state == ST_DISPLAY_OFF || state == ST_SUSPENDED) {
 		mutex_unlock(&dp->event_mutex);
 		return 0;
 	}
@@ -903,9 +926,13 @@ static int dp_display_disable(struct dp_display_private *dp, u32 data)
 
 	dp_display->audio_enabled = false;
 
-	dp_ctrl_off(dp->ctrl);
-
-	dp->core_initialized = false;
+	/* triggered by irq_hpd with sink_count = 0 */
+	if (dp->link->sink_count == 0) {
+		dp_ctrl_off_link_stream(dp->ctrl);
+	} else {
+		dp_ctrl_off(dp->ctrl);
+		dp->core_initialized = false;
+	}
 
 	dp_display->power_on = false;
 
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project


^ permalink raw reply	[flat|nested] 4+ messages in thread

* Re: [PATCH v6 1/2] drm/msm/dp: handle irq_hpd with sink_count = 0 correctly
  2021-05-19 20:22 [PATCH v6 1/2] drm/msm/dp: handle irq_hpd with sink_count = 0 correctly Kuogee Hsieh
@ 2021-05-21 21:56 ` Stephen Boyd
  2021-05-21 22:15   ` khsieh
  2021-05-21 22:27   ` khsieh
  0 siblings, 2 replies; 4+ messages in thread
From: Stephen Boyd @ 2021-05-21 21:56 UTC (permalink / raw)
  To: Kuogee Hsieh, agross, bjorn.andersson, robdclark, sean, vkoul
  Cc: abhinavk, aravindh, linux-arm-msm, linux-kernel

Quoting Kuogee Hsieh (2021-05-19 13:22:33)
> irq_hpd interrupt should be handled after dongle plugged in and
> before dongle unplugged. Hence irq_hpd interrupt is enabled at
> the end of the plugin handle and disabled at the beginning of
> unplugged handle. Current irq_hpd with sink_count = 0 is wrongly
> handled same as the dongle unplugged which tears down the mainlink
> and disables the phy. This patch fixes this problem by only tearing
> down the mainlink but keeping phy enabled at irq_hpd with
> sink_count = 0 handle so that next irq_hpd with sink_count =1 can be
> handled by setup mainlink only. This patch also set dongle into D3
> (power off) state at end of handling irq_hpd with sink_count = 0.
>
> Changes in v2:
> -- add ctrl->phy_Power_count
>
> Changes in v3:
> -- del ctrl->phy_Power_count
> -- add phy_power_off to dp_ctrl_off_link_stream()
>
> Changes in v4:
> -- return immediately if clock disable failed at dp_ctrl_off_link_stream()
>
> Changes in v5:
> -- set dongle to D3 (power off) state at dp_ctrl_off_link_stream()
>
> Changes in v6:
> -- add Fixes tag
>
> Fixes: 94e58e2d06e3 ("drm/msm/dp: reset dp controller only at boot up and pm_resume")
>
> Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
> ---

Tested-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>

We can resolve the lingering dual irq issue later on if you don't want
to send another round of this. Also, the title says 1/2 so I wonder if
there's another patch? Doesn't look like there is but I have to ask. If
not, please generate patches with the right -<N> argument or revision
range.

^ permalink raw reply	[flat|nested] 4+ messages in thread

* Re: [PATCH v6 1/2] drm/msm/dp: handle irq_hpd with sink_count = 0 correctly
  2021-05-21 21:56 ` Stephen Boyd
@ 2021-05-21 22:15   ` khsieh
  2021-05-21 22:27   ` khsieh
  1 sibling, 0 replies; 4+ messages in thread
From: khsieh @ 2021-05-21 22:15 UTC (permalink / raw)
  To: Stephen Boyd
  Cc: agross, bjorn.andersson, robdclark, sean, vkoul, abhinavk,
	aravindh, linux-arm-msm, linux-kernel

On 2021-05-21 14:56, Stephen Boyd wrote:
> Quoting Kuogee Hsieh (2021-05-19 13:22:33)
>> irq_hpd interrupt should be handled after dongle plugged in and
>> before dongle unplugged. Hence irq_hpd interrupt is enabled at
>> the end of the plugin handle and disabled at the beginning of
>> unplugged handle. Current irq_hpd with sink_count = 0 is wrongly
>> handled same as the dongle unplugged which tears down the mainlink
>> and disables the phy. This patch fixes this problem by only tearing
>> down the mainlink but keeping phy enabled at irq_hpd with
>> sink_count = 0 handle so that next irq_hpd with sink_count =1 can be
>> handled by setup mainlink only. This patch also set dongle into D3
>> (power off) state at end of handling irq_hpd with sink_count = 0.
>> 
>> Changes in v2:
>> -- add ctrl->phy_Power_count
>> 
>> Changes in v3:
>> -- del ctrl->phy_Power_count
>> -- add phy_power_off to dp_ctrl_off_link_stream()
>> 
>> Changes in v4:
>> -- return immediately if clock disable failed at 
>> dp_ctrl_off_link_stream()
>> 
>> Changes in v5:
>> -- set dongle to D3 (power off) state at dp_ctrl_off_link_stream()
>> 
>> Changes in v6:
>> -- add Fixes tag
>> 
>> Fixes: 94e58e2d06e3 ("drm/msm/dp: reset dp controller only at boot up 
>> and pm_resume")
>> 
>> Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
>> ---
> 
> Tested-by: Stephen Boyd <swboyd@chromium.org>
> Reviewed-by: Stephen Boyd <swboyd@chromium.org>
> 
> We can resolve the lingering dual irq issue later on if you don't want
> to send another round of this. Also, the title says 1/2 so I wonder if
> there's another patch? Doesn't look like there is but I have to ask. If
> not, please generate patches with the right -<N> argument or revision
> range.
ok, thanks,
Sorry, the 2nd patch is the xlog debug patch.
I did not submit it.

^ permalink raw reply	[flat|nested] 4+ messages in thread

* Re: [PATCH v6 1/2] drm/msm/dp: handle irq_hpd with sink_count = 0 correctly
  2021-05-21 21:56 ` Stephen Boyd
  2021-05-21 22:15   ` khsieh
@ 2021-05-21 22:27   ` khsieh
  1 sibling, 0 replies; 4+ messages in thread
From: khsieh @ 2021-05-21 22:27 UTC (permalink / raw)
  To: Stephen Boyd
  Cc: agross, bjorn.andersson, robdclark, sean, vkoul, abhinavk,
	aravindh, linux-arm-msm, linux-kernel

On 2021-05-21 14:56, Stephen Boyd wrote:
> Quoting Kuogee Hsieh (2021-05-19 13:22:33)
>> irq_hpd interrupt should be handled after dongle plugged in and
>> before dongle unplugged. Hence irq_hpd interrupt is enabled at
>> the end of the plugin handle and disabled at the beginning of
>> unplugged handle. Current irq_hpd with sink_count = 0 is wrongly
>> handled same as the dongle unplugged which tears down the mainlink
>> and disables the phy. This patch fixes this problem by only tearing
>> down the mainlink but keeping phy enabled at irq_hpd with
>> sink_count = 0 handle so that next irq_hpd with sink_count =1 can be
>> handled by setup mainlink only. This patch also set dongle into D3
>> (power off) state at end of handling irq_hpd with sink_count = 0.
>> 
>> Changes in v2:
>> -- add ctrl->phy_Power_count
>> 
>> Changes in v3:
>> -- del ctrl->phy_Power_count
>> -- add phy_power_off to dp_ctrl_off_link_stream()
>> 
>> Changes in v4:
>> -- return immediately if clock disable failed at 
>> dp_ctrl_off_link_stream()
>> 
>> Changes in v5:
>> -- set dongle to D3 (power off) state at dp_ctrl_off_link_stream()
>> 
>> Changes in v6:
>> -- add Fixes tag
>> 
>> Fixes: 94e58e2d06e3 ("drm/msm/dp: reset dp controller only at boot up 
>> and pm_resume")
>> 
>> Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
>> ---
> 
> Tested-by: Stephen Boyd <swboyd@chromium.org>
> Reviewed-by: Stephen Boyd <swboyd@chromium.org>
> 
> We can resolve the lingering dual irq issue later on if you don't want
> to send another round of this. Also, the title says 1/2 so I wonder if
> there's another patch? Doesn't look like there is but I have to ask. If
> not, please generate patches with the right -<N> argument or revision
> range.
new v6 uploaded

^ permalink raw reply	[flat|nested] 4+ messages in thread

end of thread, other threads:[~2021-05-21 22:29 UTC | newest]

Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-05-19 20:22 [PATCH v6 1/2] drm/msm/dp: handle irq_hpd with sink_count = 0 correctly Kuogee Hsieh
2021-05-21 21:56 ` Stephen Boyd
2021-05-21 22:15   ` khsieh
2021-05-21 22:27   ` khsieh

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).