* [PATCH v18 1/4] dt-bindings: msm: disp: add yaml schemas for DPU bindings
@ 2021-05-24 11:44 Krishna Manikandan
2021-05-24 11:44 ` [PATCH v18 2/4] dt-bindings: msm: dsi: add yaml schemas for DSI bindings Krishna Manikandan
` (2 more replies)
0 siblings, 3 replies; 5+ messages in thread
From: Krishna Manikandan @ 2021-05-24 11:44 UTC (permalink / raw)
To: dri-devel, linux-arm-msm, freedreno, devicetree, linux-kernel
Cc: Krishna Manikandan, kalyan_t, tanmay, abhinavk, robdclark,
swboyd, bjorn.andersson, vinod.koul, dianders, khsieh, robh+dt,
sean, robh
MSM Mobile Display Subsystem (MDSS) encapsulates sub-blocks
like DPU display controller, DSI etc. Add YAML schema
for DPU device tree bindings.
Signed-off-by: Krishna Manikandan <mkrishn@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
---
Changes in v2:
- Changed dpu to DPU (Sam Ravnborg)
- Fixed indentation issues (Sam Ravnborg)
- Added empty line between different properties (Sam Ravnborg)
- Replaced reference txt files with their corresponding
yaml files (Sam Ravnborg)
- Modified the file to use "|" only when it is
necessary (Sam Ravnborg)
Changes in v3:
- Corrected the license used (Rob Herring)
- Added maxItems for properties (Rob Herring)
- Dropped generic descriptions (Rob Herring)
- Added ranges property (Rob Herring)
- Corrected the indendation (Rob Herring)
- Added additionalProperties (Rob Herring)
- Split dsi file into two, one for dsi controller
and another one for dsi phy per target (Rob Herring)
- Corrected description for pinctrl-names (Rob Herring)
- Corrected the examples used in yaml file (Rob Herring)
- Delete dsi.txt and dpu.txt (Rob Herring)
Changes in v4:
- Move schema up by one level (Rob Herring)
- Add patternProperties for mdp node (Rob Herring)
- Corrected description of some properties (Rob Herring)
Changes in v5:
- Correct the indentation (Rob Herring)
- Remove unnecessary description from properties (Rob Herring)
- Correct the number of interconnect entries (Rob Herring)
- Add interconnect names for sc7180 (Rob Herring)
- Add description for ports (Rob Herring)
- Remove common properties (Rob Herring)
- Add unevalutatedProperties (Rob Herring)
- Reference existing dsi controller yaml in the common
dsi controller file (Rob Herring)
- Correct the description of clock names to include only the
clocks that are required (Rob Herring)
- Remove properties which are already covered under the common
binding (Rob Herring)
- Add dsi phy supply nodes which are required for sc7180 and
sdm845 targets (Rob Herring)
- Add type ref for syscon-sfpb (Rob Herring)
Changes in v6:
- Fixed errors during dt_binding_check (Rob Herring)
- Add maxItems for phys and phys-names (Rob Herring)
- Use unevaluatedProperties wherever required (Rob Herring)
- Removed interrupt controller from required properties for
dsi controller (Rob Herring)
- Add constraints for dsi-phy reg-names based on the compatible
phy version (Rob Herring)
- Add constraints for dsi-phy supply nodes based on the
compatible phy version (Rob Herring)
Changes in v7:
- Add default value for qcom,mdss-mdp-transfer-time-us (Rob Herring)
- Modify the schema for data-lanes (Rob Herring)
- Split the phy schema into separate schemas based on
the phy version (Rob Herring)
Changes in v8:
- Resolve merge conflicts with latest dsi.txt file
- Include dp yaml change also in the same series
Changes in v9:
- Combine target specific dsi controller yaml files
to a single yaml file (Rob Herring)
- Combine target specific dsi phy yaml files into a
single yaml file (Rob Herring)
- Use unevaluatedProperties and additionalProperties
wherever required
- Remove duplicate properties from common yaml files
Changes in v10:
- Split the patch into separate patches for DPU, DSI and
PHY (Stephen Boyd)
- Drop unnecessary fullstop (Stephen Boyd)
- Add newline whereever required (Stephen Boyd)
- Add description for clock used (Stephen Boyd)
- Modify the description for interconnect entries (Stephen Boyd)
- Drop assigned clock entries as it a generic property (Stephen Boyd)
- Correct the definition for interrupts (Stephen Boyd)
- Drop clock names from required properties (Stephen Boyd)
- Drop labels for display nodes from example (Stephen Boyd)
- Drop flags from interrupts entries (Stephen Boyd)
Changes in v11:
- Drop maxItems for clocks (Stephen Boyd)
Changes in v12:
- Add description for register property (Stephen Boyd)
- Add maxItems for interrupts (Stephen Boyd)
- Add description for iommus property (Stephen Boyd)
- Add description for interconnects (Stephen Boyd)
- Change display node name to display_controller (Stephen Boyd)
Changes in v13:
- Add maxItems for reg property (Stephen Boyd)
- Add ranges property in example (Stephen Boyd)
- Modify description for iommus property (Stephen Boyd)
- Add Dp bindings for ports in the same patch (Stephen Boyd)
- Remove soc from examples and change address and size cells
accordingly (Stephen Boyd)
- Add reference for ports
Changes in v14:
- Modify title for SC7180 and SDM845 yaml files (Stephen Boyd)
- Add required list for display-controller node (Stephen Boyd)
Changes in v16:
- Add reference for port (Rob Herring)
- Make additionalProperties as false (Rob Herring)
.../bindings/display/msm/dpu-sc7180.yaml | 228 +++++++++++++++++++++
.../bindings/display/msm/dpu-sdm845.yaml | 212 +++++++++++++++++++
.../devicetree/bindings/display/msm/dpu.txt | 141 -------------
3 files changed, 440 insertions(+), 141 deletions(-)
create mode 100644 Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml
create mode 100644 Documentation/devicetree/bindings/display/msm/dpu-sdm845.yaml
delete mode 100644 Documentation/devicetree/bindings/display/msm/dpu.txt
diff --git a/Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml b/Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml
new file mode 100644
index 0000000..12a86b1
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml
@@ -0,0 +1,228 @@
+# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/msm/dpu-sc7180.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Display DPU dt properties for SC7180 target
+
+maintainers:
+ - Krishna Manikandan <mkrishn@codeaurora.org>
+
+description: |
+ Device tree bindings for MSM Mobile Display Subsystem(MDSS) that encapsulates
+ sub-blocks like DPU display controller, DSI and DP interfaces etc. Device tree
+ bindings of MDSS and DPU are mentioned for SC7180 target.
+
+properties:
+ compatible:
+ items:
+ - const: qcom,sc7180-mdss
+
+ reg:
+ maxItems: 1
+
+ reg-names:
+ const: mdss
+
+ power-domains:
+ maxItems: 1
+
+ clocks:
+ items:
+ - description: Display AHB clock from gcc
+ - description: Display AHB clock from dispcc
+ - description: Display core clock
+
+ clock-names:
+ items:
+ - const: iface
+ - const: ahb
+ - const: core
+
+ interrupts:
+ maxItems: 1
+
+ interrupt-controller: true
+
+ "#address-cells": true
+
+ "#size-cells": true
+
+ "#interrupt-cells":
+ const: 1
+
+ iommus:
+ items:
+ - description: Phandle to apps_smmu node with SID mask for Hard-Fail port0
+
+ ranges: true
+
+ interconnects:
+ items:
+ - description: Interconnect path specifying the port ids for data bus
+
+ interconnect-names:
+ const: mdp0-mem
+
+patternProperties:
+ "^display-controller@[0-9a-f]+$":
+ type: object
+ description: Node containing the properties of DPU.
+
+ properties:
+ compatible:
+ items:
+ - const: qcom,sc7180-dpu
+
+ reg:
+ items:
+ - description: Address offset and size for mdp register set
+ - description: Address offset and size for vbif register set
+
+ reg-names:
+ items:
+ - const: mdp
+ - const: vbif
+
+ clocks:
+ items:
+ - description: Display hf axi clock
+ - description: Display ahb clock
+ - description: Display rotator clock
+ - description: Display lut clock
+ - description: Display core clock
+ - description: Display vsync clock
+
+ clock-names:
+ items:
+ - const: bus
+ - const: iface
+ - const: rot
+ - const: lut
+ - const: core
+ - const: vsync
+
+ interrupts:
+ maxItems: 1
+
+ power-domains:
+ maxItems: 1
+
+ operating-points-v2: true
+
+ ports:
+ $ref: /schemas/graph.yaml#/properties/ports
+ description: |
+ Contains the list of output ports from DPU device. These ports
+ connect to interfaces that are external to the DPU hardware,
+ such as DSI, DP etc. Each output port contains an endpoint that
+ describes how it is connected to an external interface.
+
+ properties:
+ port@0:
+ $ref: /schemas/graph.yaml#/properties/port
+ description: DPU_INTF1 (DSI1)
+
+ port@2:
+ $ref: /schemas/graph.yaml#/properties/port
+ description: DPU_INTF0 (DP)
+
+ required:
+ - port@0
+
+ required:
+ - compatible
+ - reg
+ - reg-names
+ - clocks
+ - interrupts
+ - power-domains
+ - operating-points-v2
+ - ports
+
+required:
+ - compatible
+ - reg
+ - reg-names
+ - power-domains
+ - clocks
+ - interrupts
+ - interrupt-controller
+ - iommus
+ - ranges
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/qcom,dispcc-sc7180.h>
+ #include <dt-bindings/clock/qcom,gcc-sc7180.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/interconnect/qcom,sdm845.h>
+ #include <dt-bindings/power/qcom-rpmpd.h>
+
+ display-subsystem@ae00000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "qcom,sc7180-mdss";
+ reg = <0xae00000 0x1000>;
+ reg-names = "mdss";
+ power-domains = <&dispcc MDSS_GDSC>;
+ clocks = <&gcc GCC_DISP_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_CLK>;
+ clock-names = "iface", "ahb", "core";
+
+ interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ interconnects = <&mmss_noc MASTER_MDP0 &mc_virt SLAVE_EBI1>;
+ interconnect-names = "mdp0-mem";
+
+ iommus = <&apps_smmu 0x800 0x2>;
+ ranges;
+
+ display-controller@ae01000 {
+ compatible = "qcom,sc7180-dpu";
+ reg = <0x0ae01000 0x8f000>,
+ <0x0aeb0000 0x2008>;
+
+ reg-names = "mdp", "vbif";
+
+ clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_ROT_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_CLK>,
+ <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+ clock-names = "bus", "iface", "rot", "lut", "core",
+ "vsync";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <0>;
+ power-domains = <&rpmhpd SC7180_CX>;
+ operating-points-v2 = <&mdp_opp_table>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dpu_intf1_out: endpoint {
+ remote-endpoint = <&dsi0_in>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+ dpu_intf0_out: endpoint {
+ remote-endpoint = <&dp_in>;
+ };
+ };
+ };
+ };
+ };
+...
diff --git a/Documentation/devicetree/bindings/display/msm/dpu-sdm845.yaml b/Documentation/devicetree/bindings/display/msm/dpu-sdm845.yaml
new file mode 100644
index 0000000..b4ea7c9
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/msm/dpu-sdm845.yaml
@@ -0,0 +1,212 @@
+# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/msm/dpu-sdm845.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Display DPU dt properties for SDM845 target
+
+maintainers:
+ - Krishna Manikandan <mkrishn@codeaurora.org>
+
+description: |
+ Device tree bindings for MSM Mobile Display Subsystem(MDSS) that encapsulates
+ sub-blocks like DPU display controller, DSI and DP interfaces etc. Device tree
+ bindings of MDSS and DPU are mentioned for SDM845 target.
+
+properties:
+ compatible:
+ items:
+ - const: qcom,sdm845-mdss
+
+ reg:
+ maxItems: 1
+
+ reg-names:
+ const: mdss
+
+ power-domains:
+ maxItems: 1
+
+ clocks:
+ items:
+ - description: Display AHB clock from gcc
+ - description: Display AXI clock
+ - description: Display core clock
+
+ clock-names:
+ items:
+ - const: iface
+ - const: bus
+ - const: core
+
+ interrupts:
+ maxItems: 1
+
+ interrupt-controller: true
+
+ "#address-cells": true
+
+ "#size-cells": true
+
+ "#interrupt-cells":
+ const: 1
+
+ iommus:
+ items:
+ - description: Phandle to apps_smmu node with SID mask for Hard-Fail port0
+ - description: Phandle to apps_smmu node with SID mask for Hard-Fail port1
+
+ ranges: true
+
+patternProperties:
+ "^display-controller@[0-9a-f]+$":
+ type: object
+ description: Node containing the properties of DPU.
+
+ properties:
+ compatible:
+ items:
+ - const: qcom,sdm845-dpu
+
+ reg:
+ items:
+ - description: Address offset and size for mdp register set
+ - description: Address offset and size for vbif register set
+
+ reg-names:
+ items:
+ - const: mdp
+ - const: vbif
+
+ clocks:
+ items:
+ - description: Display ahb clock
+ - description: Display axi clock
+ - description: Display core clock
+ - description: Display vsync clock
+
+ clock-names:
+ items:
+ - const: iface
+ - const: bus
+ - const: core
+ - const: vsync
+
+ interrupts:
+ maxItems: 1
+
+ power-domains:
+ maxItems: 1
+
+ operating-points-v2: true
+ ports:
+ $ref: /schemas/graph.yaml#/properties/ports
+ description: |
+ Contains the list of output ports from DPU device. These ports
+ connect to interfaces that are external to the DPU hardware,
+ such as DSI, DP etc. Each output port contains an endpoint that
+ describes how it is connected to an external interface.
+
+ properties:
+ port@0:
+ $ref: /schemas/graph.yaml#/properties/port
+ description: DPU_INTF1 (DSI1)
+
+ port@1:
+ $ref: /schemas/graph.yaml#/properties/port
+ description: DPU_INTF2 (DSI2)
+
+ required:
+ - port@0
+ - port@1
+
+ required:
+ - compatible
+ - reg
+ - reg-names
+ - clocks
+ - interrupts
+ - power-domains
+ - operating-points-v2
+ - ports
+
+required:
+ - compatible
+ - reg
+ - reg-names
+ - power-domains
+ - clocks
+ - interrupts
+ - interrupt-controller
+ - iommus
+ - ranges
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/qcom,dispcc-sdm845.h>
+ #include <dt-bindings/clock/qcom,gcc-sdm845.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/power/qcom-rpmpd.h>
+
+ display-subsystem@ae00000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "qcom,sdm845-mdss";
+ reg = <0x0ae00000 0x1000>;
+ reg-names = "mdss";
+ power-domains = <&dispcc MDSS_GDSC>;
+
+ clocks = <&gcc GCC_DISP_AHB_CLK>,
+ <&gcc GCC_DISP_AXI_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_CLK>;
+ clock-names = "iface", "bus", "core";
+
+ interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ iommus = <&apps_smmu 0x880 0x8>,
+ <&apps_smmu 0xc80 0x8>;
+ ranges;
+
+ display-controller@ae01000 {
+ compatible = "qcom,sdm845-dpu";
+ reg = <0x0ae01000 0x8f000>,
+ <0x0aeb0000 0x2008>;
+ reg-names = "mdp", "vbif";
+
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_AXI_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_CLK>,
+ <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+ clock-names = "iface", "bus", "core", "vsync";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <0>;
+ power-domains = <&rpmhpd SDM845_CX>;
+ operating-points-v2 = <&mdp_opp_table>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dpu_intf1_out: endpoint {
+ remote-endpoint = <&dsi0_in>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ dpu_intf2_out: endpoint {
+ remote-endpoint = <&dsi1_in>;
+ };
+ };
+ };
+ };
+ };
+...
diff --git a/Documentation/devicetree/bindings/display/msm/dpu.txt b/Documentation/devicetree/bindings/display/msm/dpu.txt
deleted file mode 100644
index 586e6ea..0000000
--- a/Documentation/devicetree/bindings/display/msm/dpu.txt
+++ /dev/null
@@ -1,141 +0,0 @@
-Qualcomm Technologies, Inc. DPU KMS
-
-Description:
-
-Device tree bindings for MSM Mobile Display Subsystem(MDSS) that encapsulates
-sub-blocks like DPU display controller, DSI and DP interfaces etc.
-The DPU display controller is found in SDM845 SoC.
-
-MDSS:
-Required properties:
-- compatible: "qcom,sdm845-mdss", "qcom,sc7180-mdss"
-- reg: physical base address and length of controller's registers.
-- reg-names: register region names. The following region is required:
- * "mdss"
-- power-domains: a power domain consumer specifier according to
- Documentation/devicetree/bindings/power/power_domain.txt
-- clocks: list of clock specifiers for clocks needed by the device.
-- clock-names: device clock names, must be in same order as clocks property.
- The following clocks are required:
- * "iface"
- * "bus"
- * "core"
-- interrupts: interrupt signal from MDSS.
-- interrupt-controller: identifies the node as an interrupt controller.
-- #interrupt-cells: specifies the number of cells needed to encode an interrupt
- source, should be 1.
-- iommus: phandle of iommu device node.
-- #address-cells: number of address cells for the MDSS children. Should be 1.
-- #size-cells: Should be 1.
-- ranges: parent bus address space is the same as the child bus address space.
-- interconnects : interconnect path specifier for MDSS according to
- Documentation/devicetree/bindings/interconnect/interconnect.txt. Should be
- 2 paths corresponding to 2 AXI ports.
-- interconnect-names : MDSS will have 2 port names to differentiate between the
- 2 interconnect paths defined with interconnect specifier.
-
-Optional properties:
-- assigned-clocks: list of clock specifiers for clocks needing rate assignment
-- assigned-clock-rates: list of clock frequencies sorted in the same order as
- the assigned-clocks property.
-
-MDP:
-Required properties:
-- compatible: "qcom,sdm845-dpu", "qcom,sc7180-dpu"
-- reg: physical base address and length of controller's registers.
-- reg-names : register region names. The following region is required:
- * "mdp"
- * "vbif"
-- clocks: list of clock specifiers for clocks needed by the device.
-- clock-names: device clock names, must be in same order as clocks property.
- The following clocks are required.
- * "bus"
- * "iface"
- * "core"
- * "vsync"
-- interrupts: interrupt line from DPU to MDSS.
-- ports: contains the list of output ports from DPU device. These ports connect
- to interfaces that are external to the DPU hardware, such as DSI, DP etc.
-
- Each output port contains an endpoint that describes how it is connected to an
- external interface. These are described by the standard properties documented
- here:
- Documentation/devicetree/bindings/graph.txt
- Documentation/devicetree/bindings/media/video-interfaces.txt
-
- Port 0 -> DPU_INTF1 (DSI1)
- Port 1 -> DPU_INTF2 (DSI2)
-
-Optional properties:
-- assigned-clocks: list of clock specifiers for clocks needing rate assignment
-- assigned-clock-rates: list of clock frequencies sorted in the same order as
- the assigned-clocks property.
-
-Example:
-
- mdss: mdss@ae00000 {
- compatible = "qcom,sdm845-mdss";
- reg = <0xae00000 0x1000>;
- reg-names = "mdss";
-
- power-domains = <&clock_dispcc 0>;
-
- clocks = <&gcc GCC_DISP_AHB_CLK>, <&gcc GCC_DISP_AXI_CLK>,
- <&clock_dispcc DISP_CC_MDSS_MDP_CLK>;
- clock-names = "iface", "bus", "core";
-
- assigned-clocks = <&clock_dispcc DISP_CC_MDSS_MDP_CLK>;
- assigned-clock-rates = <300000000>;
-
- interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-controller;
- #interrupt-cells = <1>;
-
- interconnects = <&rsc_hlos MASTER_MDP0 &rsc_hlos SLAVE_EBI1>,
- <&rsc_hlos MASTER_MDP1 &rsc_hlos SLAVE_EBI1>;
-
- interconnect-names = "mdp0-mem", "mdp1-mem";
-
- iommus = <&apps_iommu 0>;
-
- #address-cells = <2>;
- #size-cells = <1>;
- ranges = <0 0 0xae00000 0xb2008>;
-
- mdss_mdp: mdp@ae01000 {
- compatible = "qcom,sdm845-dpu";
- reg = <0 0x1000 0x8f000>, <0 0xb0000 0x2008>;
- reg-names = "mdp", "vbif";
-
- clocks = <&clock_dispcc DISP_CC_MDSS_AHB_CLK>,
- <&clock_dispcc DISP_CC_MDSS_AXI_CLK>,
- <&clock_dispcc DISP_CC_MDSS_MDP_CLK>,
- <&clock_dispcc DISP_CC_MDSS_VSYNC_CLK>;
- clock-names = "iface", "bus", "core", "vsync";
-
- assigned-clocks = <&clock_dispcc DISP_CC_MDSS_MDP_CLK>,
- <&clock_dispcc DISP_CC_MDSS_VSYNC_CLK>;
- assigned-clock-rates = <0 0 300000000 19200000>;
-
- interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- dpu_intf1_out: endpoint {
- remote-endpoint = <&dsi0_in>;
- };
- };
-
- port@1 {
- reg = <1>;
- dpu_intf2_out: endpoint {
- remote-endpoint = <&dsi1_in>;
- };
- };
- };
- };
- };
--
2.7.4
^ permalink raw reply related [flat|nested] 5+ messages in thread* [PATCH v18 2/4] dt-bindings: msm: dsi: add yaml schemas for DSI bindings
2021-05-24 11:44 [PATCH v18 1/4] dt-bindings: msm: disp: add yaml schemas for DPU bindings Krishna Manikandan
@ 2021-05-24 11:44 ` Krishna Manikandan
2021-05-24 22:48 ` Rob Herring
2021-05-24 11:44 ` [PATCH v18 3/4] dt-bindings: msm: dsi: add yaml schemas for DSI PHY bindings Krishna Manikandan
2021-05-24 11:44 ` [PATCH v18 4/4] dt-bindings: msm/dp: Add bindings of MSM DisplayPort controller Krishna Manikandan
2 siblings, 1 reply; 5+ messages in thread
From: Krishna Manikandan @ 2021-05-24 11:44 UTC (permalink / raw)
To: dri-devel, linux-arm-msm, freedreno, devicetree, linux-kernel
Cc: Krishna Manikandan, kalyan_t, tanmay, abhinavk, robdclark,
swboyd, bjorn.andersson, vinod.koul, dianders, khsieh, robh+dt,
sean, robh
Add YAML schema for the device tree bindings for DSI
Signed-off-by: Krishna Manikandan <mkrishn@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
---
Changes in v1:
- Separate dsi controller bindings to a separate patch (Stephen Boyd)
- Merge dsi-common-controller.yaml and dsi-controller-main.yaml to
a single file (Stephen Boyd)
- Drop supply entries and definitions from properties (Stephen Boyd)
- Modify phy-names property for dsi controller (Stephen Boyd)
- Remove boolean from description (Stephen Boyd)
- Drop pinctrl properties as they are standard entries (Stephen Boyd)
- Modify the description for ports property and keep the reference
to the generic binding where this is defined (Stephen Boyd)
- Add description to clock names (Stephen Boyd)
- Correct the indendation (Stephen Boyd)
- Drop the label for display dt nodes and correct the node
name (Stephen Boyd)
Changes in v2:
- Drop maxItems for clock (Stephen Boyd)
- Drop qcom,mdss-mdp-transfer-time-us as it is not used in upstream
dt file (Stephen Boyd)
- Keep child node directly under soc node (Stephen Boyd)
- Drop qcom,sync-dual-dsi as it is not used in upstream dt
Changes in v3:
- Add description for register property (Stephen Boyd)
Changes in v4:
- Add maxItems for phys property (Stephen Boyd)
- Add maxItems for reg property (Stephen Boyd)
- Add reference for data-lanes property (Stephen Boyd)
- Remove soc from example (Stephen Boyd)
Changes in v5:
- Modify title and description (Stephen Boyd)
- Add required properties for ports node (Stephen Boyd)
- Add data-lanes in the example (Stephen Boyd)
- Drop qcom,master-dsi property (Stephen Boyd)
Changes in v6:
- Add required properties for port@0, port@1 and corresponding
endpoints (Stephen Boyd)
- Add address-cells and size-cells for ports (Stephen Boyd)
- Use additionalProperties instead of unevaluatedProperties (Stephen Boyd)
Changes in v7:
- Add reference for ports and data-lanes (Rob Herring)
- Add maxItems and minItems for data-lanes (Rob Herring)
Changes in v8:
- Drop common properties and description from ports (Rob Herring)
- Add reference for endpoint (Rob Herring)
- Add correct reference for data-lanes (Rob Herring)
- Drop common properties from required list for ports (Rob Herring)
Changes in v9:
- Drop reference for data-lanes (Rob Herring)
- Add unevaluatedProperties for endpoint (Rob Herring)
.../bindings/display/msm/dsi-controller-main.yaml | 185 +++++++++++++++
.../devicetree/bindings/display/msm/dsi.txt | 249 ---------------------
2 files changed, 185 insertions(+), 249 deletions(-)
create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml
delete mode 100644 Documentation/devicetree/bindings/display/msm/dsi.txt
diff --git a/Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml b/Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml
new file mode 100644
index 0000000..76348b7
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml
@@ -0,0 +1,185 @@
+# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/msm/dsi-controller-main.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Display DSI controller
+
+maintainers:
+ - Krishna Manikandan <mkrishn@codeaurora.org>
+
+allOf:
+ - $ref: "../dsi-controller.yaml#"
+
+properties:
+ compatible:
+ items:
+ - const: qcom,mdss-dsi-ctrl
+
+ reg:
+ maxItems: 1
+
+ reg-names:
+ const: dsi_ctrl
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ items:
+ - description: Display byte clock
+ - description: Display byte interface clock
+ - description: Display pixel clock
+ - description: Display escape clock
+ - description: Display AHB clock
+ - description: Display AXI clock
+
+ clock-names:
+ items:
+ - const: byte
+ - const: byte_intf
+ - const: pixel
+ - const: core
+ - const: iface
+ - const: bus
+
+ phys:
+ maxItems: 1
+
+ phy-names:
+ const: dsi
+
+ "#address-cells": true
+
+ "#size-cells": true
+
+ syscon-sfpb:
+ description: A phandle to mmss_sfpb syscon node (only for DSIv2).
+ $ref: "/schemas/types.yaml#/definitions/phandle"
+
+ qcom,dual-dsi-mode:
+ type: boolean
+ description: |
+ Indicates if the DSI controller is driving a panel which needs
+ 2 DSI links.
+
+ power-domains:
+ maxItems: 1
+
+ operating-points-v2: true
+
+ ports:
+ $ref: "/schemas/graph.yaml#/properties/ports"
+ description: |
+ Contains DSI controller input and output ports as children, each
+ containing one endpoint subnode.
+
+ properties:
+ port@0:
+ $ref: "/schemas/graph.yaml#/properties/port"
+ description: |
+ Input endpoints of the controller.
+ properties:
+ endpoint:
+ $ref: /schemas/media/video-interfaces.yaml#
+ unevaluatedProperties: false
+ properties:
+ data-lanes:
+ maxItems: 4
+ minItems: 4
+ items:
+ enum: [ 0, 1, 2, 3 ]
+
+ port@1:
+ $ref: "/schemas/graph.yaml#/properties/port"
+ description: |
+ Output endpoints of the controller.
+ properties:
+ endpoint:
+ $ref: /schemas/media/video-interfaces.yaml#
+ unevaluatedProperties: false
+ properties:
+ data-lanes:
+ maxItems: 4
+ minItems: 4
+ items:
+ enum: [ 0, 1, 2, 3 ]
+
+ required:
+ - port@0
+ - port@1
+
+required:
+ - compatible
+ - reg
+ - reg-names
+ - interrupts
+ - clocks
+ - clock-names
+ - phys
+ - phy-names
+ - power-domains
+ - operating-points-v2
+ - ports
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/clock/qcom,dispcc-sdm845.h>
+ #include <dt-bindings/clock/qcom,gcc-sdm845.h>
+ #include <dt-bindings/power/qcom-rpmpd.h>
+
+ dsi@ae94000 {
+ compatible = "qcom,mdss-dsi-ctrl";
+ reg = <0x0ae94000 0x400>;
+ reg-names = "dsi_ctrl";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ interrupt-parent = <&mdss>;
+ interrupts = <4>;
+
+ clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
+ <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
+ <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
+ <&dispcc DISP_CC_MDSS_ESC0_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_AXI_CLK>;
+ clock-names = "byte",
+ "byte_intf",
+ "pixel",
+ "core",
+ "iface",
+ "bus";
+
+ phys = <&dsi0_phy>;
+ phy-names = "dsi";
+
+ power-domains = <&rpmhpd SC7180_CX>;
+ operating-points-v2 = <&dsi_opp_table>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dsi0_in: endpoint {
+ remote-endpoint = <&dpu_intf1_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ dsi0_out: endpoint {
+ remote-endpoint = <&sn65dsi86_in>;
+ data-lanes = <0 1 2 3>;
+ };
+ };
+ };
+ };
+...
diff --git a/Documentation/devicetree/bindings/display/msm/dsi.txt b/Documentation/devicetree/bindings/display/msm/dsi.txt
deleted file mode 100644
index b9a64d3..0000000
--- a/Documentation/devicetree/bindings/display/msm/dsi.txt
+++ /dev/null
@@ -1,249 +0,0 @@
-Qualcomm Technologies Inc. adreno/snapdragon DSI output
-
-DSI Controller:
-Required properties:
-- compatible:
- * "qcom,mdss-dsi-ctrl"
-- reg: Physical base address and length of the registers of controller
-- reg-names: The names of register regions. The following regions are required:
- * "dsi_ctrl"
-- interrupts: The interrupt signal from the DSI block.
-- power-domains: Should be <&mmcc MDSS_GDSC>.
-- clocks: Phandles to device clocks.
-- clock-names: the following clocks are required:
- * "mdp_core"
- * "iface"
- * "bus"
- * "core_mmss"
- * "byte"
- * "pixel"
- * "core"
- For DSIv2, we need an additional clock:
- * "src"
- For DSI6G v2.0 onwards, we need also need the clock:
- * "byte_intf"
-- assigned-clocks: Parents of "byte" and "pixel" for the given platform.
-- assigned-clock-parents: The Byte clock and Pixel clock PLL outputs provided
- by a DSI PHY block. See [1] for details on clock bindings.
-- vdd-supply: phandle to vdd regulator device node
-- vddio-supply: phandle to vdd-io regulator device node
-- vdda-supply: phandle to vdda regulator device node
-- phys: phandle to DSI PHY device node
-- phy-names: the name of the corresponding PHY device
-- syscon-sfpb: A phandle to mmss_sfpb syscon node (only for DSIv2)
-- ports: Contains 2 DSI controller ports as child nodes. Each port contains
- an endpoint subnode as defined in [2] and [3].
-
-Optional properties:
-- panel@0: Node of panel connected to this DSI controller.
- See files in [4] for each supported panel.
-- qcom,dual-dsi-mode: Boolean value indicating if the DSI controller is
- driving a panel which needs 2 DSI links.
-- qcom,master-dsi: Boolean value indicating if the DSI controller is driving
- the master link of the 2-DSI panel.
-- qcom,sync-dual-dsi: Boolean value indicating if the DSI controller is
- driving a 2-DSI panel whose 2 links need receive command simultaneously.
-- pinctrl-names: the pin control state names; should contain "default"
-- pinctrl-0: the default pinctrl state (active)
-- pinctrl-n: the "sleep" pinctrl state
-- ports: contains DSI controller input and output ports as children, each
- containing one endpoint subnode.
-
- DSI Endpoint properties:
- - remote-endpoint: For port@0, set to phandle of the connected panel/bridge's
- input endpoint. For port@1, set to the MDP interface output. See [2] for
- device graph info.
-
- - data-lanes: this describes how the physical DSI data lanes are mapped
- to the logical lanes on the given platform. The value contained in
- index n describes what physical lane is mapped to the logical lane n
- (DATAn, where n lies between 0 and 3). The clock lane position is fixed
- and can't be changed. Hence, they aren't a part of the DT bindings. See
- [3] for more info on the data-lanes property.
-
- For example:
-
- data-lanes = <3 0 1 2>;
-
- The above mapping describes that the logical data lane DATA0 is mapped to
- the physical data lane DATA3, logical DATA1 to physical DATA0, logic DATA2
- to phys DATA1 and logic DATA3 to phys DATA2.
-
- There are only a limited number of physical to logical mappings possible:
- <0 1 2 3>
- <1 2 3 0>
- <2 3 0 1>
- <3 0 1 2>
- <0 3 2 1>
- <1 0 3 2>
- <2 1 0 3>
- <3 2 1 0>
-
-DSI PHY:
-Required properties:
-- compatible: Could be the following
- * "qcom,dsi-phy-28nm-hpm"
- * "qcom,dsi-phy-28nm-lp"
- * "qcom,dsi-phy-20nm"
- * "qcom,dsi-phy-28nm-8960"
- * "qcom,dsi-phy-14nm"
- * "qcom,dsi-phy-14nm-660"
- * "qcom,dsi-phy-10nm"
- * "qcom,dsi-phy-10nm-8998"
- * "qcom,dsi-phy-7nm"
- * "qcom,dsi-phy-7nm-8150"
-- reg: Physical base address and length of the registers of PLL, PHY. Some
- revisions require the PHY regulator base address, whereas others require the
- PHY lane base address. See below for each PHY revision.
-- reg-names: The names of register regions. The following regions are required:
- For DSI 28nm HPM/LP/8960 PHYs and 20nm PHY:
- * "dsi_pll"
- * "dsi_phy"
- * "dsi_phy_regulator"
- For DSI 14nm, 10nm and 7nm PHYs:
- * "dsi_pll"
- * "dsi_phy"
- * "dsi_phy_lane"
-- clock-cells: Must be 1. The DSI PHY block acts as a clock provider, creating
- 2 clocks: A byte clock (index 0), and a pixel clock (index 1).
-- power-domains: Should be <&mmcc MDSS_GDSC>.
-- clocks: Phandles to device clocks. See [1] for details on clock bindings.
-- clock-names: the following clocks are required:
- * "iface"
- * "ref" (only required for new DTS files/entries)
- For 28nm HPM/LP, 28nm 8960 PHYs:
-- vddio-supply: phandle to vdd-io regulator device node
- For 20nm PHY:
-- vddio-supply: phandle to vdd-io regulator device node
-- vcca-supply: phandle to vcca regulator device node
- For 14nm PHY:
-- vcca-supply: phandle to vcca regulator device node
- For 10nm and 7nm PHY:
-- vdds-supply: phandle to vdds regulator device node
-
-Optional properties:
-- qcom,dsi-phy-regulator-ldo-mode: Boolean value indicating if the LDO mode PHY
- regulator is wanted.
-- qcom,mdss-mdp-transfer-time-us: Specifies the dsi transfer time for command mode
- panels in microseconds. Driver uses this number to adjust
- the clock rate according to the expected transfer time.
- Increasing this value would slow down the mdp processing
- and can result in slower performance.
- Decreasing this value can speed up the mdp processing,
- but this can also impact power consumption.
- As a rule this time should not be higher than the time
- that would be expected with the processing at the
- dsi link rate since anyways this would be the maximum
- transfer time that could be achieved.
- If ping pong split is enabled, this time should not be higher
- than two times the dsi link rate time.
- If the property is not specified, then the default value is 14000 us.
-
-[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
-[2] Documentation/devicetree/bindings/graph.txt
-[3] Documentation/devicetree/bindings/media/video-interfaces.txt
-[4] Documentation/devicetree/bindings/display/panel/
-
-Example:
- dsi0: dsi@fd922800 {
- compatible = "qcom,mdss-dsi-ctrl";
- qcom,dsi-host-index = <0>;
- interrupt-parent = <&mdp>;
- interrupts = <4 0>;
- reg-names = "dsi_ctrl";
- reg = <0xfd922800 0x200>;
- power-domains = <&mmcc MDSS_GDSC>;
- clock-names =
- "bus",
- "byte",
- "core",
- "core_mmss",
- "iface",
- "mdp_core",
- "pixel";
- clocks =
- <&mmcc MDSS_AXI_CLK>,
- <&mmcc MDSS_BYTE0_CLK>,
- <&mmcc MDSS_ESC0_CLK>,
- <&mmcc MMSS_MISC_AHB_CLK>,
- <&mmcc MDSS_AHB_CLK>,
- <&mmcc MDSS_MDP_CLK>,
- <&mmcc MDSS_PCLK0_CLK>;
-
- assigned-clocks =
- <&mmcc BYTE0_CLK_SRC>,
- <&mmcc PCLK0_CLK_SRC>;
- assigned-clock-parents =
- <&dsi_phy0 0>,
- <&dsi_phy0 1>;
-
- vdda-supply = <&pma8084_l2>;
- vdd-supply = <&pma8084_l22>;
- vddio-supply = <&pma8084_l12>;
-
- phys = <&dsi_phy0>;
- phy-names ="dsi-phy";
-
- qcom,dual-dsi-mode;
- qcom,master-dsi;
- qcom,sync-dual-dsi;
-
- qcom,mdss-mdp-transfer-time-us = <12000>;
-
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&dsi_active>;
- pinctrl-1 = <&dsi_suspend>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- dsi0_in: endpoint {
- remote-endpoint = <&mdp_intf1_out>;
- };
- };
-
- port@1 {
- reg = <1>;
- dsi0_out: endpoint {
- remote-endpoint = <&panel_in>;
- data-lanes = <0 1 2 3>;
- };
- };
- };
-
- panel: panel@0 {
- compatible = "sharp,lq101r1sx01";
- reg = <0>;
- link2 = <&secondary>;
-
- power-supply = <...>;
- backlight = <...>;
-
- port {
- panel_in: endpoint {
- remote-endpoint = <&dsi0_out>;
- };
- };
- };
- };
-
- dsi_phy0: dsi-phy@fd922a00 {
- compatible = "qcom,dsi-phy-28nm-hpm";
- qcom,dsi-phy-index = <0>;
- reg-names =
- "dsi_pll",
- "dsi_phy",
- "dsi_phy_regulator";
- reg = <0xfd922a00 0xd4>,
- <0xfd922b00 0x2b0>,
- <0xfd922d80 0x7b>;
- clock-names = "iface";
- clocks = <&mmcc MDSS_AHB_CLK>;
- #clock-cells = <1>;
- vddio-supply = <&pma8084_l12>;
-
- qcom,dsi-phy-regulator-ldo-mode;
- };
--
2.7.4
^ permalink raw reply related [flat|nested] 5+ messages in thread* Re: [PATCH v18 2/4] dt-bindings: msm: dsi: add yaml schemas for DSI bindings
2021-05-24 11:44 ` [PATCH v18 2/4] dt-bindings: msm: dsi: add yaml schemas for DSI bindings Krishna Manikandan
@ 2021-05-24 22:48 ` Rob Herring
0 siblings, 0 replies; 5+ messages in thread
From: Rob Herring @ 2021-05-24 22:48 UTC (permalink / raw)
To: Krishna Manikandan
Cc: robh+dt, dri-devel, linux-arm-msm, khsieh, linux-kernel,
dianders, abhinavk, tanmay, freedreno, swboyd, devicetree,
vinod.koul, kalyan_t, bjorn.andersson, sean
On Mon, 24 May 2021 17:14:11 +0530, Krishna Manikandan wrote:
> Add YAML schema for the device tree bindings for DSI
>
> Signed-off-by: Krishna Manikandan <mkrishn@codeaurora.org>
> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> Reviewed-by: Stephen Boyd <swboyd@chromium.org>
> ---
> Changes in v1:
> - Separate dsi controller bindings to a separate patch (Stephen Boyd)
> - Merge dsi-common-controller.yaml and dsi-controller-main.yaml to
> a single file (Stephen Boyd)
> - Drop supply entries and definitions from properties (Stephen Boyd)
> - Modify phy-names property for dsi controller (Stephen Boyd)
> - Remove boolean from description (Stephen Boyd)
> - Drop pinctrl properties as they are standard entries (Stephen Boyd)
> - Modify the description for ports property and keep the reference
> to the generic binding where this is defined (Stephen Boyd)
> - Add description to clock names (Stephen Boyd)
> - Correct the indendation (Stephen Boyd)
> - Drop the label for display dt nodes and correct the node
> name (Stephen Boyd)
>
> Changes in v2:
> - Drop maxItems for clock (Stephen Boyd)
> - Drop qcom,mdss-mdp-transfer-time-us as it is not used in upstream
> dt file (Stephen Boyd)
> - Keep child node directly under soc node (Stephen Boyd)
> - Drop qcom,sync-dual-dsi as it is not used in upstream dt
>
> Changes in v3:
> - Add description for register property (Stephen Boyd)
>
> Changes in v4:
> - Add maxItems for phys property (Stephen Boyd)
> - Add maxItems for reg property (Stephen Boyd)
> - Add reference for data-lanes property (Stephen Boyd)
> - Remove soc from example (Stephen Boyd)
>
> Changes in v5:
> - Modify title and description (Stephen Boyd)
> - Add required properties for ports node (Stephen Boyd)
> - Add data-lanes in the example (Stephen Boyd)
> - Drop qcom,master-dsi property (Stephen Boyd)
>
> Changes in v6:
> - Add required properties for port@0, port@1 and corresponding
> endpoints (Stephen Boyd)
> - Add address-cells and size-cells for ports (Stephen Boyd)
> - Use additionalProperties instead of unevaluatedProperties (Stephen Boyd)
>
> Changes in v7:
> - Add reference for ports and data-lanes (Rob Herring)
> - Add maxItems and minItems for data-lanes (Rob Herring)
>
> Changes in v8:
> - Drop common properties and description from ports (Rob Herring)
> - Add reference for endpoint (Rob Herring)
> - Add correct reference for data-lanes (Rob Herring)
> - Drop common properties from required list for ports (Rob Herring)
>
> Changes in v9:
> - Drop reference for data-lanes (Rob Herring)
> - Add unevaluatedProperties for endpoint (Rob Herring)
>
> .../bindings/display/msm/dsi-controller-main.yaml | 185 +++++++++++++++
> .../devicetree/bindings/display/msm/dsi.txt | 249 ---------------------
> 2 files changed, 185 insertions(+), 249 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml
> delete mode 100644 Documentation/devicetree/bindings/display/msm/dsi.txt
>
Reviewed-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH v18 3/4] dt-bindings: msm: dsi: add yaml schemas for DSI PHY bindings
2021-05-24 11:44 [PATCH v18 1/4] dt-bindings: msm: disp: add yaml schemas for DPU bindings Krishna Manikandan
2021-05-24 11:44 ` [PATCH v18 2/4] dt-bindings: msm: dsi: add yaml schemas for DSI bindings Krishna Manikandan
@ 2021-05-24 11:44 ` Krishna Manikandan
2021-05-24 11:44 ` [PATCH v18 4/4] dt-bindings: msm/dp: Add bindings of MSM DisplayPort controller Krishna Manikandan
2 siblings, 0 replies; 5+ messages in thread
From: Krishna Manikandan @ 2021-05-24 11:44 UTC (permalink / raw)
To: dri-devel, linux-arm-msm, freedreno, devicetree, linux-kernel
Cc: Krishna Manikandan, kalyan_t, tanmay, abhinavk, robdclark,
swboyd, bjorn.andersson, vinod.koul, dianders, khsieh, robh+dt,
sean, robh
Add YAML schema for the device tree bindings for DSI PHY.
Signed-off-by: Krishna Manikandan <mkrishn@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
---
Changes in v1:
- Merge dsi-phy.yaml and dsi-phy-10nm.yaml (Stephen Boyd)
- Remove qcom,dsi-phy-regulator-ldo-mode (Stephen Boyd)
- Add clock cells properly (Stephen Boyd)
- Remove unnecessary decription from clock names (Stephen Boyd)
- Add pin names for the supply entries for 10nm phy which is
used in sc7180 and sdm845 (Stephen Boyd)
- Remove unused header files from examples (Stephen Boyd)
- Drop labels for display nodes and correct node name (Stephen Boyd)
Changes in v2:
- Drop maxItems for clock (Stephen Boyd)
- Add vdds supply pin information for sdm845 (Stephen Boyd)
- Add examples for 14nm, 20nm and 28nm phy yaml files (Stephen Boyd)
- Keep child nodes directly under soc node (Stephen Boyd)
Changes in v3:
- Use a separate yaml file to describe the common properties
for all the dsi phy versions (Stephen Boyd)
- Remove soc from examples (Stephen Boyd)
- Add description for register property
Changes in v4:
- Modify the title for all the phy versions (Stephen Boyd)
- Drop description for all the phy versions (Stephen Boyd)
- Modify the description for register property (Stephen Boyd)
Changes in v5:
- Remove unused properties from common dsi phy file
- Add clock-cells and phy-cells to required property
list (Stephen Boyd)
Changes in v6:
- Add proper compatible string in example
.../bindings/display/msm/dsi-phy-10nm.yaml | 68 +++++++++++++++++++++
.../bindings/display/msm/dsi-phy-14nm.yaml | 66 ++++++++++++++++++++
.../bindings/display/msm/dsi-phy-20nm.yaml | 71 ++++++++++++++++++++++
.../bindings/display/msm/dsi-phy-28nm.yaml | 68 +++++++++++++++++++++
.../bindings/display/msm/dsi-phy-common.yaml | 40 ++++++++++++
5 files changed, 313 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-phy-10nm.yaml
create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-phy-14nm.yaml
create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-phy-20nm.yaml
create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-phy-28nm.yaml
create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-phy-common.yaml
diff --git a/Documentation/devicetree/bindings/display/msm/dsi-phy-10nm.yaml b/Documentation/devicetree/bindings/display/msm/dsi-phy-10nm.yaml
new file mode 100644
index 0000000..4a26bef
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/msm/dsi-phy-10nm.yaml
@@ -0,0 +1,68 @@
+# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/msm/dsi-phy-10nm.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Display DSI 10nm PHY
+
+maintainers:
+ - Krishna Manikandan <mkrishn@codeaurora.org>
+
+allOf:
+ - $ref: dsi-phy-common.yaml#
+
+properties:
+ compatible:
+ oneOf:
+ - const: qcom,dsi-phy-10nm
+ - const: qcom,dsi-phy-10nm-8998
+
+ reg:
+ items:
+ - description: dsi phy register set
+ - description: dsi phy lane register set
+ - description: dsi pll register set
+
+ reg-names:
+ items:
+ - const: dsi_phy
+ - const: dsi_phy_lane
+ - const: dsi_pll
+
+ vdds-supply:
+ description: |
+ Connected to DSI0_MIPI_DSI_PLL_VDDA0P9 pin for sc7180 target and
+ connected to VDDA_MIPI_DSI_0_PLL_0P9 pin for sdm845 target
+
+required:
+ - compatible
+ - reg
+ - reg-names
+ - vdds-supply
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/qcom,dispcc-sdm845.h>
+ #include <dt-bindings/clock/qcom,rpmh.h>
+
+ dsi-phy@ae94400 {
+ compatible = "qcom,dsi-phy-10nm";
+ reg = <0x0ae94400 0x200>,
+ <0x0ae94600 0x280>,
+ <0x0ae94a00 0x1e0>;
+ reg-names = "dsi_phy",
+ "dsi_phy_lane",
+ "dsi_pll";
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+
+ vdds-supply = <&vdda_mipi_dsi0_pll>;
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "iface", "ref";
+ };
+...
diff --git a/Documentation/devicetree/bindings/display/msm/dsi-phy-14nm.yaml b/Documentation/devicetree/bindings/display/msm/dsi-phy-14nm.yaml
new file mode 100644
index 0000000..72a00cc
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/msm/dsi-phy-14nm.yaml
@@ -0,0 +1,66 @@
+# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/msm/dsi-phy-14nm.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Display DSI 14nm PHY
+
+maintainers:
+ - Krishna Manikandan <mkrishn@codeaurora.org>
+
+allOf:
+ - $ref: dsi-phy-common.yaml#
+
+properties:
+ compatible:
+ oneOf:
+ - const: qcom,dsi-phy-14nm
+ - const: qcom,dsi-phy-14nm-660
+
+ reg:
+ items:
+ - description: dsi phy register set
+ - description: dsi phy lane register set
+ - description: dsi pll register set
+
+ reg-names:
+ items:
+ - const: dsi_phy
+ - const: dsi_phy_lane
+ - const: dsi_pll
+
+ vcca-supply:
+ description: Phandle to vcca regulator device node.
+
+required:
+ - compatible
+ - reg
+ - reg-names
+ - vcca-supply
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/qcom,dispcc-sdm845.h>
+ #include <dt-bindings/clock/qcom,rpmh.h>
+
+ dsi-phy@ae94400 {
+ compatible = "qcom,dsi-phy-14nm";
+ reg = <0x0ae94400 0x200>,
+ <0x0ae94600 0x280>,
+ <0x0ae94a00 0x1e0>;
+ reg-names = "dsi_phy",
+ "dsi_phy_lane",
+ "dsi_pll";
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+
+ vcca-supply = <&vcca_reg>;
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "iface", "ref";
+ };
+...
diff --git a/Documentation/devicetree/bindings/display/msm/dsi-phy-20nm.yaml b/Documentation/devicetree/bindings/display/msm/dsi-phy-20nm.yaml
new file mode 100644
index 0000000..743806d
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/msm/dsi-phy-20nm.yaml
@@ -0,0 +1,71 @@
+# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/msm/dsi-phy-20nm.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Display DSI 20nm PHY
+
+maintainers:
+ - Krishna Manikandan <mkrishn@codeaurora.org>
+
+allOf:
+ - $ref: dsi-phy-common.yaml#
+
+properties:
+ compatible:
+ oneOf:
+ - const: qcom,dsi-phy-20nm
+
+ reg:
+ items:
+ - description: dsi pll register set
+ - description: dsi phy register set
+ - description: dsi phy regulator register set
+
+ reg-names:
+ items:
+ - const: dsi_pll
+ - const: dsi_phy
+ - const: dsi_phy_regulator
+
+ vcca-supply:
+ description: Phandle to vcca regulator device node.
+
+ vddio-supply:
+ description: Phandle to vdd-io regulator device node.
+
+required:
+ - compatible
+ - reg
+ - reg-names
+ - vddio-supply
+ - vcca-supply
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/qcom,dispcc-sdm845.h>
+ #include <dt-bindings/clock/qcom,rpmh.h>
+
+ dsi-phy@fd922a00 {
+ compatible = "qcom,dsi-phy-20nm";
+ reg = <0xfd922a00 0xd4>,
+ <0xfd922b00 0x2b0>,
+ <0xfd922d80 0x7b>;
+ reg-names = "dsi_pll",
+ "dsi_phy",
+ "dsi_phy_regulator";
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+
+ vcca-supply = <&vcca_reg>;
+ vddio-supply = <&vddio_reg>;
+
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "iface", "ref";
+ };
+...
diff --git a/Documentation/devicetree/bindings/display/msm/dsi-phy-28nm.yaml b/Documentation/devicetree/bindings/display/msm/dsi-phy-28nm.yaml
new file mode 100644
index 0000000..b106007
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/msm/dsi-phy-28nm.yaml
@@ -0,0 +1,68 @@
+# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/msm/dsi-phy-28nm.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Display DSI 28nm PHY
+
+maintainers:
+ - Krishna Manikandan <mkrishn@codeaurora.org>
+
+allOf:
+ - $ref: dsi-phy-common.yaml#
+
+properties:
+ compatible:
+ oneOf:
+ - const: qcom,dsi-phy-28nm-hpm
+ - const: qcom,dsi-phy-28nm-lp
+ - const: qcom,dsi-phy-28nm-8960
+
+ reg:
+ items:
+ - description: dsi pll register set
+ - description: dsi phy register set
+ - description: dsi phy regulator register set
+
+ reg-names:
+ items:
+ - const: dsi_pll
+ - const: dsi_phy
+ - const: dsi_phy_regulator
+
+ vddio-supply:
+ description: Phandle to vdd-io regulator device node.
+
+required:
+ - compatible
+ - reg
+ - reg-names
+ - vddio-supply
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/qcom,dispcc-sdm845.h>
+ #include <dt-bindings/clock/qcom,rpmh.h>
+
+ dsi-phy@fd922a00 {
+ compatible = "qcom,dsi-phy-28nm-lp";
+ reg = <0xfd922a00 0xd4>,
+ <0xfd922b00 0x2b0>,
+ <0xfd922d80 0x7b>;
+ reg-names = "dsi_pll",
+ "dsi_phy",
+ "dsi_phy_regulator";
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+
+ vddio-supply = <&vddio_reg>;
+
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "iface", "ref";
+ };
+...
diff --git a/Documentation/devicetree/bindings/display/msm/dsi-phy-common.yaml b/Documentation/devicetree/bindings/display/msm/dsi-phy-common.yaml
new file mode 100644
index 0000000..502bdda
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/msm/dsi-phy-common.yaml
@@ -0,0 +1,40 @@
+# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/msm/dsi-phy-common.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Description of Qualcomm Display DSI PHY common dt properties
+
+maintainers:
+ - Krishna Manikandan <mkrishn@codeaurora.org>
+
+description: |
+ This defines the DSI PHY dt properties which are common for all
+ dsi phy versions.
+
+properties:
+ "#clock-cells":
+ const: 1
+
+ "#phy-cells":
+ const: 0
+
+ clocks:
+ items:
+ - description: Display AHB clock
+ - description: Board XO source
+
+ clock-names:
+ items:
+ - const: iface
+ - const: ref
+
+required:
+ - clocks
+ - clock-names
+ - "#clock-cells"
+ - "#phy-cells"
+
+additionalProperties: true
+...
--
2.7.4
^ permalink raw reply related [flat|nested] 5+ messages in thread* [PATCH v18 4/4] dt-bindings: msm/dp: Add bindings of MSM DisplayPort controller
2021-05-24 11:44 [PATCH v18 1/4] dt-bindings: msm: disp: add yaml schemas for DPU bindings Krishna Manikandan
2021-05-24 11:44 ` [PATCH v18 2/4] dt-bindings: msm: dsi: add yaml schemas for DSI bindings Krishna Manikandan
2021-05-24 11:44 ` [PATCH v18 3/4] dt-bindings: msm: dsi: add yaml schemas for DSI PHY bindings Krishna Manikandan
@ 2021-05-24 11:44 ` Krishna Manikandan
2 siblings, 0 replies; 5+ messages in thread
From: Krishna Manikandan @ 2021-05-24 11:44 UTC (permalink / raw)
To: dri-devel, linux-arm-msm, freedreno, devicetree, linux-kernel
Cc: Krishna Manikandan, kalyan_t, tanmay, abhinavk, robdclark,
swboyd, bjorn.andersson, vinod.koul, dianders, khsieh, robh+dt,
sean, robh, Chandan Uddaraju, Vara Reddy
Add bindings for Snapdragon DisplayPort controller driver.
Signed-off-by: Chandan Uddaraju <chandanu@codeaurora.org>
Signed-off-by: Vara Reddy <varar@codeaurora.org>
Signed-off-by: Tanmay Shah <tanmay@codeaurora.org>
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Signed-off-by: Krishna Manikandan <mkrishn@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
---
Changes in V2:
-Provide details about sel-gpio
Changes in V4:
-Provide details about max dp lanes
-Change the commit text
Changes in V5:
-moved dp.txt to yaml file
Changes in v6:
- Squash all AUX LUT properties into one pattern Property
- Make aux-cfg[0-9]-settings properties optional
- Remove PLL/PHY bindings from DP controller dts
- Add DP clocks description
- Remove _clk suffix from clock names
- Rename pixel clock to stream_pixel
- Remove redundant bindings (GPIO, PHY, HDCP clock, etc..)
- Fix indentation
- Add Display Port as interface of DPU in DPU bindings
and add port mapping accordingly.
Chages in v7:
- Add dp-controller.yaml file common between multiple SOC
- Rename dp-sc7180.yaml to dp-controller-sc7180.yaml
- change compatible string and add SOC name to it.
- Remove Root clock generator for pixel clock
- Add assigned-clocks and assigned-clock-parents bindings
- Remove redundant properties, descriptions and blank lines
- Add DP port in DPU bindings
- Update depends-on tag in commit message and rebase change accordingly
Changes in v8:
- Add MDSS AHB clock in bindings
Changes in v9:
- Remove redundant reg-name property
- Change assigned-clocks and assigned-clocks-parents counts to 2
- Use IRQ flags in example dts
Changes in v10:
- Change title of this patch as it does not contain PLL bindings anymore
- Remove redundant properties
- Remove use of IRQ flag
- Fix ports property
Changes in v11:
- add ports required of both #address-cells and #size-cells
- add required operating-points-v2
- add required #sound-dai-cells
- add required power-domains
- update maintainer list
Changes in v12:
- remove soc node from examples (Stephen Boyd)
- split dpu-sc7180.yaml changes to separate patch (Stephen Boyd)
Changes in v13:
- add assigned-clocks
- add assigned-clock-parents
Changes in v14:
- add reference for ports (Rob Herring)
Changes in v15:
- drop common properties from ports (Rob Herring)
.../bindings/display/msm/dp-controller.yaml | 146 +++++++++++++++++++++
1 file changed, 146 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/msm/dp-controller.yaml
diff --git a/Documentation/devicetree/bindings/display/msm/dp-controller.yaml b/Documentation/devicetree/bindings/display/msm/dp-controller.yaml
new file mode 100644
index 0000000..64d8d9e
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/msm/dp-controller.yaml
@@ -0,0 +1,146 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/msm/dp-controller.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MSM Display Port Controller
+
+maintainers:
+ - Kuogee Hsieh <khsieh@codeaurora.org>
+
+description: |
+ Device tree bindings for DisplayPort host controller for MSM targets
+ that are compatible with VESA DisplayPort interface specification.
+
+properties:
+ compatible:
+ enum:
+ - qcom,sc7180-dp
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ items:
+ - description: AHB clock to enable register access
+ - description: Display Port AUX clock
+ - description: Display Port Link clock
+ - description: Link interface clock between DP and PHY
+ - description: Display Port Pixel clock
+
+ clock-names:
+ items:
+ - const: core_iface
+ - const: core_aux
+ - const: ctrl_link
+ - const: ctrl_link_iface
+ - const: stream_pixel
+
+ assigned-clocks:
+ items:
+ - description: link clock source
+ - description: pixel clock source
+
+ assigned-clock-parents:
+ items:
+ - description: phy 0 parent
+ - description: phy 1 parent
+
+ phys:
+ maxItems: 1
+
+ phy-names:
+ items:
+ - const: dp
+
+ operating-points-v2:
+ maxItems: 1
+
+ power-domains:
+ maxItems: 1
+
+ "#sound-dai-cells":
+ const: 0
+
+ ports:
+ $ref: /schemas/graph.yaml#/properties/ports
+ properties:
+ port@0:
+ $ref: /schemas/graph.yaml#/properties/port
+ description: Input endpoint of the controller
+
+ port@1:
+ $ref: /schemas/graph.yaml#/properties/port
+ description: Output endpoint of the controller
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - clocks
+ - clock-names
+ - phys
+ - phy-names
+ - "#sound-dai-cells"
+ - power-domains
+ - ports
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/clock/qcom,dispcc-sc7180.h>
+ #include <dt-bindings/power/qcom-aoss-qmp.h>
+ #include <dt-bindings/power/qcom-rpmpd.h>
+
+ displayport-controller@ae90000 {
+ compatible = "qcom,sc7180-dp";
+ reg = <0xae90000 0x1400>;
+ interrupt-parent = <&mdss>;
+ interrupts = <12>;
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_DP_AUX_CLK>,
+ <&dispcc DISP_CC_MDSS_DP_LINK_CLK>,
+ <&dispcc DISP_CC_MDSS_DP_LINK_INTF_CLK>,
+ <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK>;
+ clock-names = "core_iface", "core_aux",
+ "ctrl_link",
+ "ctrl_link_iface", "stream_pixel";
+
+ assigned-clocks = <&dispcc DISP_CC_MDSS_DP_LINK_CLK_SRC>,
+ <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK_SRC>;
+
+ assigned-clock-parents = <&dp_phy 0>, <&dp_phy 1>;
+
+ phys = <&dp_phy>;
+ phy-names = "dp";
+
+ #sound-dai-cells = <0>;
+
+ power-domains = <&rpmhpd SC7180_CX>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ endpoint {
+ remote-endpoint = <&dpu_intf0_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ endpoint {
+ remote-endpoint = <&typec>;
+ };
+ };
+ };
+ };
+...
--
2.7.4
^ permalink raw reply related [flat|nested] 5+ messages in thread
end of thread, other threads:[~2021-05-24 22:48 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-05-24 11:44 [PATCH v18 1/4] dt-bindings: msm: disp: add yaml schemas for DPU bindings Krishna Manikandan
2021-05-24 11:44 ` [PATCH v18 2/4] dt-bindings: msm: dsi: add yaml schemas for DSI bindings Krishna Manikandan
2021-05-24 22:48 ` Rob Herring
2021-05-24 11:44 ` [PATCH v18 3/4] dt-bindings: msm: dsi: add yaml schemas for DSI PHY bindings Krishna Manikandan
2021-05-24 11:44 ` [PATCH v18 4/4] dt-bindings: msm/dp: Add bindings of MSM DisplayPort controller Krishna Manikandan
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).