linux-arm-msm.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Kuogee Hsieh <khsieh@codeaurora.org>
To: robdclark@gmail.com, sean@poorly.run, swboyd@chromium.org
Cc: Kuogee Hsieh <khsieh@codeaurora.org>,
	abhinavk@codeaurora.org, aravindh@codeaurora.org,
	airlied@linux.ie, daniel@ffwll.ch, linux-arm-msm@vger.kernel.org,
	dri-devel@lists.freedesktop.org, freedreno@lists.freedesktop.org,
	linux-kernel@vger.kernel.org
Subject: [PATCH v4 6/6] drm/msm/dp: do not end dp link training until video is ready
Date: Wed, 11 Aug 2021 09:30:07 -0700	[thread overview]
Message-ID: <1628699407-28358-7-git-send-email-khsieh@codeaurora.org> (raw)
In-Reply-To: <1628699407-28358-1-git-send-email-khsieh@codeaurora.org>

Initialize both pre-emphasis and voltage swing level to 0 before
start link training and do not end link training until video is
ready to reduce the period between end of link training and video
start to meet Link Layer CTS requirement.  Some dongle main link
symbol may become unlocked again if host did not end link training
soon enough after completion of link training 2. Host have to re
train main link if loss of symbol locked detected before end link
training so that the coming video stream can be transmitted to sink
properly. This fixes Link Layer CTS cases 4.3.2.1, 4.3.2.2, 4.3.2.3
and 4.3.2.4.

Changes in v3:
-- merge retrain link if loss of symbol locked happen into this patch
-- replace dp_ctrl_loss_symbol_lock() with dp_ctrl_channel_eq_ok()

Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
---
 drivers/gpu/drm/msm/dp/dp_ctrl.c | 56 +++++++++++++++++++++++++++++-----------
 1 file changed, 41 insertions(+), 15 deletions(-)

diff --git a/drivers/gpu/drm/msm/dp/dp_ctrl.c b/drivers/gpu/drm/msm/dp/dp_ctrl.c
index 0002805..ffed523 100644
--- a/drivers/gpu/drm/msm/dp/dp_ctrl.c
+++ b/drivers/gpu/drm/msm/dp/dp_ctrl.c
@@ -1484,6 +1484,9 @@ static int dp_ctrl_link_maintenance(struct dp_ctrl_private *ctrl)
 
 	dp_ctrl_push_idle(&ctrl->dp_ctrl);
 
+	ctrl->link->phy_params.p_level = 0;
+	ctrl->link->phy_params.v_level = 0;
+
 	ctrl->dp_ctrl.pixel_rate = ctrl->panel->dp_mode.drm_mode.clock;
 
 	ret = dp_ctrl_setup_main_link(ctrl, &training_step);
@@ -1636,6 +1639,16 @@ static bool dp_ctrl_clock_recovery_any_ok(
 	return drm_dp_clock_recovery_ok(link_status, reduced_cnt);
 }
 
+static bool dp_ctrl_channel_eq_ok(struct dp_ctrl_private *ctrl)
+{
+	u8 link_status[DP_LINK_STATUS_SIZE];
+	int num_lanes = ctrl->link->link_params.num_lanes;
+
+	dp_ctrl_read_link_status(ctrl, link_status);
+
+	return drm_dp_channel_eq_ok(link_status, num_lanes);
+}
+
 int dp_ctrl_on_link(struct dp_ctrl *dp_ctrl)
 {
 	int rc = 0;
@@ -1671,6 +1684,9 @@ int dp_ctrl_on_link(struct dp_ctrl *dp_ctrl)
 		ctrl->link->link_params.rate,
 		ctrl->link->link_params.num_lanes, ctrl->dp_ctrl.pixel_rate);
 
+	ctrl->link->phy_params.p_level = 0;
+	ctrl->link->phy_params.v_level = 0;
+
 	rc = dp_ctrl_enable_mainlink_clocks(ctrl);
 	if (rc)
 		return rc;
@@ -1736,17 +1752,19 @@ int dp_ctrl_on_link(struct dp_ctrl *dp_ctrl)
 	if (ctrl->link->sink_request & DP_TEST_LINK_PHY_TEST_PATTERN)
 		return rc;
 
-	/* stop txing train pattern */
-	dp_ctrl_clear_training_pattern(ctrl);
+	if (rc == 0) {  /* link train successfully */
+		/*
+		 * do not stop train pattern here
+		 * stop link training at on_stream
+		 * to pass compliance test
+		 */
+	} else  {
+		/*
+		 * link training failed
+		 * end txing train pattern here
+		 */
+		dp_ctrl_clear_training_pattern(ctrl);
 
-	/*
-	 * keep transmitting idle pattern until video ready
-	 * to avoid main link from loss of sync
-	 */
-	if (rc == 0)  /* link train successfully */
-		dp_ctrl_push_idle(dp_ctrl);
-	else  {
-		/* link training failed */
 		dp_ctrl_deinitialize_mainlink(ctrl);
 		rc = -ECONNRESET;
 	}
@@ -1754,9 +1772,15 @@ int dp_ctrl_on_link(struct dp_ctrl *dp_ctrl)
 	return rc;
 }
 
+static int dp_ctrl_link_retrain(struct dp_ctrl_private *ctrl)
+{
+	int training_step = DP_TRAINING_NONE;
+
+	return dp_ctrl_setup_main_link(ctrl, &training_step);
+}
+
 int dp_ctrl_on_stream(struct dp_ctrl *dp_ctrl)
 {
-	u32 rate = 0;
 	int ret = 0;
 	bool mainlink_ready = false;
 	struct dp_ctrl_private *ctrl;
@@ -1766,10 +1790,6 @@ int dp_ctrl_on_stream(struct dp_ctrl *dp_ctrl)
 
 	ctrl = container_of(dp_ctrl, struct dp_ctrl_private, dp_ctrl);
 
-	rate = ctrl->panel->link_info.rate;
-
-	ctrl->link->link_params.rate = rate;
-	ctrl->link->link_params.num_lanes = ctrl->panel->link_info.num_lanes;
 	ctrl->dp_ctrl.pixel_rate = ctrl->panel->dp_mode.drm_mode.clock;
 
 	DRM_DEBUG_DP("rate=%d, num_lanes=%d, pixel_rate=%d\n",
@@ -1784,6 +1804,12 @@ int dp_ctrl_on_stream(struct dp_ctrl *dp_ctrl)
 		}
 	}
 
+	if (!dp_ctrl_channel_eq_ok(ctrl))
+		dp_ctrl_link_retrain(ctrl);
+
+	/* stop txing train pattern to end link training */
+	dp_ctrl_clear_training_pattern(ctrl);
+
 	ret = dp_ctrl_enable_stream_clocks(ctrl);
 	if (ret) {
 		DRM_ERROR("Failed to start pixel clocks. ret=%d\n", ret);
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project


  parent reply	other threads:[~2021-08-11 16:32 UTC|newest]

Thread overview: 8+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-08-11 16:30 [PATCH v4 0/6] add fixes to pass DP Link Layer compliance test cases Kuogee Hsieh
2021-08-11 16:30 ` [PATCH v4 1/6] drm/msm/dp: use dp_ctrl_off_link_stream during PHY compliance test run Kuogee Hsieh
2021-08-11 16:30 ` [PATCH v4 2/6] drm/msm/dp: reduce link rate if failed at link training 1 Kuogee Hsieh
2021-08-11 16:30 ` [PATCH v4 3/6] drm/msm/dp: reset aux controller after dp_aux_cmd_fifo_tx() failed Kuogee Hsieh
2021-08-11 16:30 ` [PATCH v4 4/6] drm/msm/dp: replug event is converted into an unplug followed by an plug events Kuogee Hsieh
2021-08-11 16:30 ` [PATCH v4 5/6] drm/msm/dp: return correct edid checksum after corrupted edid checksum read Kuogee Hsieh
2021-08-11 16:30 ` Kuogee Hsieh [this message]
2021-11-25 11:39 ` [PATCH v4 0/6] add fixes to pass DP Link Layer compliance test cases Dmitry Baryshkov

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1628699407-28358-7-git-send-email-khsieh@codeaurora.org \
    --to=khsieh@codeaurora.org \
    --cc=abhinavk@codeaurora.org \
    --cc=airlied@linux.ie \
    --cc=aravindh@codeaurora.org \
    --cc=daniel@ffwll.ch \
    --cc=dri-devel@lists.freedesktop.org \
    --cc=freedreno@lists.freedesktop.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=robdclark@gmail.com \
    --cc=sean@poorly.run \
    --cc=swboyd@chromium.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).