linux-arm-msm.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Balakrishna Godavarthi <bgodavar@codeaurora.org>
To: marcel@holtmann.org, johan.hedberg@gmail.com, bjorn.andersson@linaro.org
Cc: mka@chromium.org, linux-kernel@vger.kernel.org,
	linux-bluetooth@vger.kernel.org, hemantg@codeaurora.org,
	linux-arm-msm@vger.kernel.org, pharish@codeaurora.org,
	rjliao@codeaurora.org, hbandi@codeaurora.org,
	saluvala@codeaurora.org, abhishekpandit@chromium.org,
	Balakrishna Godavarthi <bgodavar@codeaurora.org>
Subject: [PATCH v2] arm64: dts: qcom: sc7280: Add bluetooth node on SC7280
Date: Tue, 12 Oct 2021 18:31:38 +0530	[thread overview]
Message-ID: <1634043698-20256-1-git-send-email-bgodavar@codeaurora.org> (raw)

Add bluetooth SoC WCN6750 node for SC7280 IDP boards.

Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
---
v2: 
  * merged two patches into one
  * Removed unused comments
  * Removed pinmux & pin conf.
  * Addressed reviewers comments 

v1: initial patch
---
 arch/arm64/boot/dts/qcom/sc7280-idp.dts  |  6 ++++++
 arch/arm64/boot/dts/qcom/sc7280-idp.dtsi | 25 +++++++++++++++++++++++++
 arch/arm64/boot/dts/qcom/sc7280-idp2.dts |  6 ++++++
 3 files changed, 37 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dts b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
index 64fc22a..d8b9262 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
@@ -16,7 +16,9 @@
 	compatible = "qcom,sc7280-idp", "google,senor", "qcom,sc7280";
 
 	aliases {
+		bluetooth0 = &bluetooth;
 		serial0 = &uart5;
+		serial1 = &uart7;
 	};
 
 	chosen {
@@ -68,3 +70,7 @@
 		qcom,pre-scaling = <1 1>;
 	};
 };
+
+&bluetooth {
+	vddio-supply = <&vreg_l19b_1p8>;
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
index 272d5ca..09adc802 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
@@ -393,6 +393,23 @@
 				<&tlmm 31 IRQ_TYPE_EDGE_FALLING>;
 	pinctrl-names = "default", "sleep";
 	pinctrl-1 = <&qup_uart7_sleep_cts>, <&qup_uart7_sleep_rts>, <&qup_uart7_sleep_tx>, <&qup_uart7_sleep_rx>;
+
+	bluetooth: wcn6750-bt {
+		compatible = "qcom,wcn6750-bt";
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_en_default>;
+		enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>;
+		swctrl-gpios = <&tlmm 86 GPIO_ACTIVE_HIGH>;
+		vddaon-supply = <&vreg_s7b_0p9>;
+		vddbtcxmx-supply = <&vreg_s7b_0p9>;
+		vddrfacmn-supply = <&vreg_s7b_0p9>;
+		vddrfa0p8-supply = <&vreg_s7b_0p9>;
+		vddrfa1p7-supply = <&vreg_s1b_1p8>;
+		vddrfa1p2-supply = <&vreg_s8b_1p2>;
+		vddrfa2p2-supply = <&vreg_s1c_2p2>;
+		vddasd-supply = <&vreg_l11c_2p8>;
+		max-speed = <3200000>;
+	};
 };
 
 /* PINCTRL - additions to nodes defined in sc7280.dtsi */
@@ -504,6 +521,14 @@
 		 */
 		bias-pull-up;
 	};
+
+	bt_en_default: bt_en_default {
+		pins = "gpio85";
+		function = "gpio";
+		drive-strength = <2>;
+		output-low;
+		bias-pull-down;
+	};
 };
 
 &sdc1_on {
diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp2.dts b/arch/arm64/boot/dts/qcom/sc7280-idp2.dts
index 1fc2add..e60fa88 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp2.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp2.dts
@@ -14,10 +14,16 @@
 	compatible = "qcom,sc7280-idp2", "google,piglin", "qcom,sc7280";
 
 	aliases {
+		bluetooth0 = &bluetooth;
 		serial0 = &uart5;
+		serial1 = &uart7;
 	};
 
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
 };
+
+&bluetooth {
+	vddio-supply = <&vreg_l18b_1p8>;
+};
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project


             reply	other threads:[~2021-10-12 13:02 UTC|newest]

Thread overview: 4+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-10-12 13:01 Balakrishna Godavarthi [this message]
2021-10-12 17:24 ` [PATCH v2] arm64: dts: qcom: sc7280: Add bluetooth node on SC7280 Stephen Boyd
2021-10-13  5:30   ` bgodavar
2021-10-13 20:14     ` Stephen Boyd

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1634043698-20256-1-git-send-email-bgodavar@codeaurora.org \
    --to=bgodavar@codeaurora.org \
    --cc=abhishekpandit@chromium.org \
    --cc=bjorn.andersson@linaro.org \
    --cc=hbandi@codeaurora.org \
    --cc=hemantg@codeaurora.org \
    --cc=johan.hedberg@gmail.com \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-bluetooth@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=marcel@holtmann.org \
    --cc=mka@chromium.org \
    --cc=pharish@codeaurora.org \
    --cc=rjliao@codeaurora.org \
    --cc=saluvala@codeaurora.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).