* [PATCH V3] net: emac: emac gigabit ethernet controller driver
@ 2015-12-30 1:48 Gilad Avidov
2015-12-30 2:31 ` kbuild test robot
` (3 more replies)
0 siblings, 4 replies; 19+ messages in thread
From: Gilad Avidov @ 2015-12-30 1:48 UTC (permalink / raw)
To: netdev-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-msm-u79uwXL29TY76Z2rM5mHXA
Cc: sdharia-sgV2jX0FEOL9JmXXK+q4OQ, shankerd-sgV2jX0FEOL9JmXXK+q4OQ,
timur-sgV2jX0FEOL9JmXXK+q4OQ,
gregkh-hQyY1W1yCW8ekmWlsbkhG0B+6BGkLq7r,
vikrams-sgV2jX0FEOL9JmXXK+q4OQ, cov-sgV2jX0FEOL9JmXXK+q4OQ,
Gilad Avidov
Add supports for ethernet controller HW on Qualcomm Technologies, Inc. SoC.
This driver supports the following features:
1) Checksum offload.
2) Runtime power management support.
3) Interrupt coalescing support.
4) SGMII phy.
5) SGMII direct connection without external phy.
Based on a driver by Niranjana Vishwanathapura
<nvishwan-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>.
Changes since v1 (https://lkml.org/lkml/2015/12/7/1088)
- replace hw bit fields to macros with bitwise operations.
- change all iterators to unsized types (int)
- some minor code flow improvements.
- change return type to void for functions which return value is never
used.
- replace instance of xxxxl_relaxed() io followed by mb() with a
readl()/writel().
Changes since v2 (https://lwn.net/Articles/667876/)
- remove most of the memory barriers by using the non xxx_relaxed() api.
- remove RSS and WOL support.
- correct comments from physical address to dma address.
- rearrange structs to make them packed.
- replace polling loops with readl_poll_timeout().
- remove unnecessary wrapper functions from phy layer.
- add blank line before return statements.
- set to null clocks after clk_put().
- use module_platform_driver() and dma_set_mask_and_coherent()
- replace long hex bitmasks with BIT() macro.
Signed-off-by: Gilad Avidov <gavidov-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
---
.../devicetree/bindings/net/qcom-emac.txt | 68 +
drivers/net/ethernet/qualcomm/Kconfig | 11 +
drivers/net/ethernet/qualcomm/Makefile | 2 +
drivers/net/ethernet/qualcomm/emac/Makefile | 7 +
drivers/net/ethernet/qualcomm/emac/emac-mac.c | 1808 ++++++++++++++++++++
drivers/net/ethernet/qualcomm/emac/emac-mac.h | 286 ++++
drivers/net/ethernet/qualcomm/emac/emac-phy.c | 486 ++++++
drivers/net/ethernet/qualcomm/emac/emac-phy.h | 69 +
drivers/net/ethernet/qualcomm/emac/emac-sgmii.c | 679 ++++++++
drivers/net/ethernet/qualcomm/emac/emac-sgmii.h | 30 +
drivers/net/ethernet/qualcomm/emac/emac.c | 1228 +++++++++++++
drivers/net/ethernet/qualcomm/emac/emac.h | 388 +++++
12 files changed, 5062 insertions(+)
create mode 100644 Documentation/devicetree/bindings/net/qcom-emac.txt
create mode 100644 drivers/net/ethernet/qualcomm/emac/Makefile
create mode 100644 drivers/net/ethernet/qualcomm/emac/emac-mac.c
create mode 100644 drivers/net/ethernet/qualcomm/emac/emac-mac.h
create mode 100644 drivers/net/ethernet/qualcomm/emac/emac-phy.c
create mode 100644 drivers/net/ethernet/qualcomm/emac/emac-phy.h
create mode 100644 drivers/net/ethernet/qualcomm/emac/emac-sgmii.c
create mode 100644 drivers/net/ethernet/qualcomm/emac/emac-sgmii.h
create mode 100644 drivers/net/ethernet/qualcomm/emac/emac.c
create mode 100644 drivers/net/ethernet/qualcomm/emac/emac.h
diff --git a/Documentation/devicetree/bindings/net/qcom-emac.txt b/Documentation/devicetree/bindings/net/qcom-emac.txt
new file mode 100644
index 0000000..8d58a40
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/qcom-emac.txt
@@ -0,0 +1,68 @@
+Qualcomm EMAC Gigabit Ethernet Controller
+
+Required properties:
+- cell-index : EMAC controller instance number.
+- compatible : Should be "qcom,emac".
+- reg : Offset and length of the register regions for the device
+- reg-names : Register region names referenced in 'reg' above.
+ Required register resource entries are:
+ "base" : EMAC controller base register block.
+ "csr" : EMAC wrapper register block.
+ Optional register resource entries are:
+ "ptp" : EMAC PTP (1588) register block.
+ Required if 'qcom,emac-tstamp-en' is present.
+ "sgmii" : EMAC SGMII PHY register block.
+- interrupts : Interrupt numbers used by this controller
+- interrupt-names : Interrupt resource names referenced in 'interrupts' above.
+ Required interrupt resource entries are:
+ "emac_core0" : EMAC core0 interrupt.
+ "sgmii_irq" : EMAC SGMII interrupt.
+- qcom,emac-gpio-mdc : GPIO pin number of the MDC line of MDIO bus.
+- qcom,emac-gpio-mdio : GPIO pin number of the MDIO line of MDIO bus.
+- phy-addr : Specifies phy address on MDIO bus.
+ Required if the optional property "qcom,no-external-phy"
+ is not specified.
+
+Optional properties:
+- qcom,emac-tstamp-en : Enables the PTP (1588) timestamping feature.
+ Include this only if PTP (1588) timestamping
+ feature is needed. If included, "ptp" register
+ base should be specified.
+- mac-address : The 6-byte MAC address. If present, it is the
+ default MAC address.
+- qcom,no-external-phy : Indicates there is no external PHY connected to
+ EMAC. Include this only if the EMAC is directly
+ connected to the peer end without EPHY.
+- qcom,emac-ptp-grandmaster : Enable the PTP (1588) grandmaster mode.
+ Include this only if PTP (1588) is configured as
+ grandmaster.
+- qcom,emac-ptp-frac-ns-adj : The vector table to adjust the fractional ns per
+ RTC clock cycle.
+ Include this only if there is accuracy loss of
+ fractional ns per RTC clock cycle. For individual
+ table entry, the first field indicates the RTC
+ reference clock rate. The second field indicates
+ the number of adjustment in 2 ^ -26 ns.
+Example:
+ emac0: qcom,emac@feb20000 {
+ cell-index = <0>;
+ compatible = "qcom,emac";
+ reg-names = "base", "csr", "ptp", "sgmii";
+ reg = <0xfeb20000 0x10000>,
+ <0xfeb36000 0x1000>,
+ <0xfeb3c000 0x4000>,
+ <0xfeb38000 0x400>;
+ #address-cells = <0>;
+ interrupt-parent = <&emac0>;
+ #interrupt-cells = <1>;
+ interrupts = <0 1>;
+ interrupt-map-mask = <0xffffffff>;
+ interrupt-map = <0 &intc 0 76 0
+ 1 &intc 0 80 0>;
+ interrupt-names = "emac_core0", "sgmii_irq";
+ qcom,emac-gpio-mdc = <&qcomgpio 123 0>;
+ qcom,emac-gpio-mdio = <&qcomgpio 124 0>;
+ qcom,emac-tstamp-en;
+ qcom,emac-ptp-frac-ns-adj = <125000000 1>;
+ phy-addr = <0>;
+ };
diff --git a/drivers/net/ethernet/qualcomm/Kconfig b/drivers/net/ethernet/qualcomm/Kconfig
index a76e380..85b599f 100644
--- a/drivers/net/ethernet/qualcomm/Kconfig
+++ b/drivers/net/ethernet/qualcomm/Kconfig
@@ -24,4 +24,15 @@ config QCA7000
To compile this driver as a module, choose M here. The module
will be called qcaspi.
+config QCOM_EMAC
+ tristate "Qualcomm Technologies, Inc. EMAC Gigabit Ethernet support"
+ select CRC32
+ ---help---
+ This driver supports the Qualcomm Technologies, Inc. Gigabit
+ Ethernet Media Access Controller (EMAC). The controller
+ supports IEEE 802.3-2002, half-duplex mode at 10/100 Mb/s,
+ full-duplex mode at 10/100/1000Mb/s, Wake On LAN (WOL) for
+ low power, Receive-Side Scaling (RSS), and IEEE 1588-2008
+ Precision Clock Synchronization Protocol.
+
endif # NET_VENDOR_QUALCOMM
diff --git a/drivers/net/ethernet/qualcomm/Makefile b/drivers/net/ethernet/qualcomm/Makefile
index 9da2d75..b14686e 100644
--- a/drivers/net/ethernet/qualcomm/Makefile
+++ b/drivers/net/ethernet/qualcomm/Makefile
@@ -4,3 +4,5 @@
obj-$(CONFIG_QCA7000) += qcaspi.o
qcaspi-objs := qca_spi.o qca_framing.o qca_7k.o qca_debug.o
+
+obj-$(CONFIG_QCOM_EMAC) += emac/
\ No newline at end of file
diff --git a/drivers/net/ethernet/qualcomm/emac/Makefile b/drivers/net/ethernet/qualcomm/emac/Makefile
new file mode 100644
index 0000000..01ee144
--- /dev/null
+++ b/drivers/net/ethernet/qualcomm/emac/Makefile
@@ -0,0 +1,7 @@
+#
+# Makefile for the Qualcomm Technologies, Inc. EMAC Gigabit Ethernet driver
+#
+
+obj-$(CONFIG_QCOM_EMAC) += qcom-emac.o
+
+qcom-emac-objs := emac.o emac-mac.o emac-phy.o emac-sgmii.o
diff --git a/drivers/net/ethernet/qualcomm/emac/emac-mac.c b/drivers/net/ethernet/qualcomm/emac/emac-mac.c
new file mode 100644
index 0000000..36a7746
--- /dev/null
+++ b/drivers/net/ethernet/qualcomm/emac/emac-mac.c
@@ -0,0 +1,1808 @@
+/* Copyright (c) 2013-2015, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+/* Qualcomm Technologies, Inc. EMAC Ethernet Controller MAC layer support
+ */
+
+#include <linux/tcp.h>
+#include <linux/ip.h>
+#include <linux/ipv6.h>
+#include <linux/crc32.h>
+#include <linux/if_vlan.h>
+#include <linux/jiffies.h>
+#include <linux/phy.h>
+#include <linux/of.h>
+#include <linux/gpio.h>
+#include <linux/pm_runtime.h>
+#include "emac.h"
+#include "emac-sgmii.h"
+
+/* EMAC base register offsets */
+#define EMAC_MAC_CTRL 0x001480
+#define EMAC_WOL_CTRL0 0x0014a0
+#define EMAC_RSS_KEY0 0x0014b0
+#define EMAC_H1TPD_BASE_ADDR_LO 0x0014e0
+#define EMAC_H2TPD_BASE_ADDR_LO 0x0014e4
+#define EMAC_H3TPD_BASE_ADDR_LO 0x0014e8
+#define EMAC_INTER_SRAM_PART9 0x001534
+#define EMAC_DESC_CTRL_0 0x001540
+#define EMAC_DESC_CTRL_1 0x001544
+#define EMAC_DESC_CTRL_2 0x001550
+#define EMAC_DESC_CTRL_10 0x001554
+#define EMAC_DESC_CTRL_12 0x001558
+#define EMAC_DESC_CTRL_13 0x00155c
+#define EMAC_DESC_CTRL_3 0x001560
+#define EMAC_DESC_CTRL_4 0x001564
+#define EMAC_DESC_CTRL_5 0x001568
+#define EMAC_DESC_CTRL_14 0x00156c
+#define EMAC_DESC_CTRL_15 0x001570
+#define EMAC_DESC_CTRL_16 0x001574
+#define EMAC_DESC_CTRL_6 0x001578
+#define EMAC_DESC_CTRL_8 0x001580
+#define EMAC_DESC_CTRL_9 0x001584
+#define EMAC_DESC_CTRL_11 0x001588
+#define EMAC_TXQ_CTRL_0 0x001590
+#define EMAC_TXQ_CTRL_1 0x001594
+#define EMAC_TXQ_CTRL_2 0x001598
+#define EMAC_RXQ_CTRL_0 0x0015a0
+#define EMAC_RXQ_CTRL_1 0x0015a4
+#define EMAC_RXQ_CTRL_2 0x0015a8
+#define EMAC_RXQ_CTRL_3 0x0015ac
+#define EMAC_BASE_CPU_NUMBER 0x0015b8
+#define EMAC_DMA_CTRL 0x0015c0
+#define EMAC_MAILBOX_0 0x0015e0
+#define EMAC_MAILBOX_5 0x0015e4
+#define EMAC_MAILBOX_6 0x0015e8
+#define EMAC_MAILBOX_13 0x0015ec
+#define EMAC_MAILBOX_2 0x0015f4
+#define EMAC_MAILBOX_3 0x0015f8
+#define EMAC_MAILBOX_11 0x00160c
+#define EMAC_AXI_MAST_CTRL 0x001610
+#define EMAC_MAILBOX_12 0x001614
+#define EMAC_MAILBOX_9 0x001618
+#define EMAC_MAILBOX_10 0x00161c
+#define EMAC_ATHR_HEADER_CTRL 0x001620
+#define EMAC_CLK_GATE_CTRL 0x001814
+#define EMAC_MISC_CTRL 0x001990
+#define EMAC_MAILBOX_7 0x0019e0
+#define EMAC_MAILBOX_8 0x0019e4
+#define EMAC_MAILBOX_15 0x001bd4
+#define EMAC_MAILBOX_16 0x001bd8
+
+/* EMAC_MAC_CTRL */
+#define SINGLE_PAUSE_MODE 0x10000000
+#define DEBUG_MODE 0x8000000
+#define BROAD_EN 0x4000000
+#define MULTI_ALL 0x2000000
+#define RX_CHKSUM_EN 0x1000000
+#define HUGE 0x800000
+#define SPEED_BMSK 0x300000
+#define SPEED_SHFT 20
+#define SIMR 0x80000
+#define TPAUSE 0x10000
+#define PROM_MODE 0x8000
+#define VLAN_STRIP 0x4000
+#define PRLEN_BMSK 0x3c00
+#define PRLEN_SHFT 10
+#define HUGEN 0x200
+#define FLCHK 0x100
+#define PCRCE 0x80
+#define CRCE 0x40
+#define FULLD 0x20
+#define MAC_LP_EN 0x10
+#define RXFC 0x8
+#define TXFC 0x4
+#define RXEN 0x2
+#define TXEN 0x1
+
+/* EMAC_WOL_CTRL0 */
+#define LK_CHG_PME 0x20
+#define LK_CHG_EN 0x10
+#define MG_FRAME_PME 0x8
+#define MG_FRAME_EN 0x4
+#define WK_FRAME_EN 0x1
+
+/* EMAC_DESC_CTRL_3 */
+#define RFD_RING_SIZE_BMSK 0xfff
+
+/* EMAC_DESC_CTRL_4 */
+#define RX_BUFFER_SIZE_BMSK 0xffff
+
+/* EMAC_DESC_CTRL_6 */
+#define RRD_RING_SIZE_BMSK 0xfff
+
+/* EMAC_DESC_CTRL_9 */
+#define TPD_RING_SIZE_BMSK 0xffff
+
+/* EMAC_TXQ_CTRL_0 */
+#define NUM_TXF_BURST_PREF_BMSK 0xffff0000
+#define NUM_TXF_BURST_PREF_SHFT 16
+#define LS_8023_SP 0x80
+#define TXQ_MODE 0x40
+#define TXQ_EN 0x20
+#define IP_OP_SP 0x10
+#define NUM_TPD_BURST_PREF_BMSK 0xf
+#define NUM_TPD_BURST_PREF_SHFT 0
+
+/* EMAC_TXQ_CTRL_1 */
+#define JUMBO_TASK_OFFLOAD_THRESHOLD_BMSK 0x7ff
+
+/* EMAC_TXQ_CTRL_2 */
+#define TXF_HWM_BMSK 0xfff0000
+#define TXF_LWM_BMSK 0xfff
+
+/* EMAC_RXQ_CTRL_0 */
+#define RXQ_EN BIT(31)
+#define CUT_THRU_EN BIT(30)
+#define RSS_HASH_EN BIT(29)
+#define NUM_RFD_BURST_PREF_BMSK 0x3f00000
+#define NUM_RFD_BURST_PREF_SHFT 20
+#define IDT_TABLE_SIZE_BMSK 0x1ff00
+#define IDT_TABLE_SIZE_SHFT 8
+#define SP_IPV6 0x80
+
+/* EMAC_RXQ_CTRL_1 */
+#define JUMBO_1KAH_BMSK 0xf000
+#define JUMBO_1KAH_SHFT 12
+#define RFD_PREF_LOW_TH 0x10
+#define RFD_PREF_LOW_THRESHOLD_BMSK 0xfc0
+#define RFD_PREF_LOW_THRESHOLD_SHFT 6
+#define RFD_PREF_UP_TH 0x10
+#define RFD_PREF_UP_THRESHOLD_BMSK 0x3f
+#define RFD_PREF_UP_THRESHOLD_SHFT 0
+
+/* EMAC_RXQ_CTRL_2 */
+#define RXF_DOF_THRESFHOLD 0x1a0
+#define RXF_DOF_THRESHOLD_BMSK 0xfff0000
+#define RXF_DOF_THRESHOLD_SHFT 16
+#define RXF_UOF_THRESFHOLD 0xbe
+#define RXF_UOF_THRESHOLD_BMSK 0xfff
+#define RXF_UOF_THRESHOLD_SHFT 0
+
+/* EMAC_RXQ_CTRL_3 */
+#define RXD_TIMER_BMSK 0xffff0000
+#define RXD_THRESHOLD_BMSK 0xfff
+#define RXD_THRESHOLD_SHFT 0
+
+/* EMAC_DMA_CTRL */
+#define DMAW_DLY_CNT_BMSK 0xf0000
+#define DMAW_DLY_CNT_SHFT 16
+#define DMAR_DLY_CNT_BMSK 0xf800
+#define DMAR_DLY_CNT_SHFT 11
+#define DMAR_REQ_PRI 0x400
+#define REGWRBLEN_BMSK 0x380
+#define REGWRBLEN_SHFT 7
+#define REGRDBLEN_BMSK 0x70
+#define REGRDBLEN_SHFT 4
+#define OUT_ORDER_MODE 0x4
+#define ENH_ORDER_MODE 0x2
+#define IN_ORDER_MODE 0x1
+
+/* EMAC_MAILBOX_13 */
+#define RFD3_PROC_IDX_BMSK 0xfff0000
+#define RFD3_PROC_IDX_SHFT 16
+#define RFD3_PROD_IDX_BMSK 0xfff
+#define RFD3_PROD_IDX_SHFT 0
+
+/* EMAC_MAILBOX_2 */
+#define NTPD_CONS_IDX_BMSK 0xffff0000
+#define NTPD_CONS_IDX_SHFT 16
+
+/* EMAC_MAILBOX_3 */
+#define RFD0_CONS_IDX_BMSK 0xfff
+#define RFD0_CONS_IDX_SHFT 0
+
+/* EMAC_MAILBOX_11 */
+#define H3TPD_PROD_IDX_BMSK 0xffff0000
+#define H3TPD_PROD_IDX_SHFT 16
+
+/* EMAC_AXI_MAST_CTRL */
+#define DATA_BYTE_SWAP 0x8
+#define MAX_BOUND 0x2
+#define MAX_BTYPE 0x1
+
+/* EMAC_MAILBOX_12 */
+#define H3TPD_CONS_IDX_BMSK 0xffff0000
+#define H3TPD_CONS_IDX_SHFT 16
+
+/* EMAC_MAILBOX_9 */
+#define H2TPD_PROD_IDX_BMSK 0xffff
+#define H2TPD_PROD_IDX_SHFT 0
+
+/* EMAC_MAILBOX_10 */
+#define H1TPD_CONS_IDX_BMSK 0xffff0000
+#define H1TPD_CONS_IDX_SHFT 16
+#define H2TPD_CONS_IDX_BMSK 0xffff
+#define H2TPD_CONS_IDX_SHFT 0
+
+/* EMAC_ATHR_HEADER_CTRL */
+#define HEADER_CNT_EN 0x2
+#define HEADER_ENABLE 0x1
+
+/* EMAC_MAILBOX_0 */
+#define RFD0_PROC_IDX_BMSK 0xfff0000
+#define RFD0_PROC_IDX_SHFT 16
+#define RFD0_PROD_IDX_BMSK 0xfff
+#define RFD0_PROD_IDX_SHFT 0
+
+/* EMAC_MAILBOX_5 */
+#define RFD1_PROC_IDX_BMSK 0xfff0000
+#define RFD1_PROC_IDX_SHFT 16
+#define RFD1_PROD_IDX_BMSK 0xfff
+#define RFD1_PROD_IDX_SHFT 0
+
+/* EMAC_MISC_CTRL */
+#define RX_UNCPL_INT_EN 0x1
+
+/* EMAC_MAILBOX_7 */
+#define RFD2_CONS_IDX_BMSK 0xfff0000
+#define RFD2_CONS_IDX_SHFT 16
+#define RFD1_CONS_IDX_BMSK 0xfff
+#define RFD1_CONS_IDX_SHFT 0
+
+/* EMAC_MAILBOX_8 */
+#define RFD3_CONS_IDX_BMSK 0xfff
+#define RFD3_CONS_IDX_SHFT 0
+
+/* EMAC_MAILBOX_15 */
+#define NTPD_PROD_IDX_BMSK 0xffff
+#define NTPD_PROD_IDX_SHFT 0
+
+/* EMAC_MAILBOX_16 */
+#define H1TPD_PROD_IDX_BMSK 0xffff
+#define H1TPD_PROD_IDX_SHFT 0
+
+#define RXQ0_RSS_HSTYP_IPV6_TCP_EN 0x20
+#define RXQ0_RSS_HSTYP_IPV6_EN 0x10
+#define RXQ0_RSS_HSTYP_IPV4_TCP_EN 0x8
+#define RXQ0_RSS_HSTYP_IPV4_EN 0x4
+
+/* DMA address */
+#define DMA_ADDR_HI_MASK 0xffffffff00000000ULL
+#define DMA_ADDR_LO_MASK 0x00000000ffffffffULL
+
+#define EMAC_DMA_ADDR_HI(_addr) \
+ ((u32)(((u64)(_addr) & DMA_ADDR_HI_MASK) >> 32))
+#define EMAC_DMA_ADDR_LO(_addr) \
+ ((u32)((u64)(_addr) & DMA_ADDR_LO_MASK))
+
+/* EMAC_EMAC_WRAPPER_TX_TS_INX */
+#define EMAC_WRAPPER_TX_TS_EMPTY BIT(31)
+#define EMAC_WRAPPER_TX_TS_INX_BMSK 0xffff
+
+struct emac_skb_cb {
+ u32 tpd_idx;
+ unsigned long jiffies;
+};
+
+struct emac_tx_ts_cb {
+ u32 sec;
+ u32 ns;
+};
+
+#define EMAC_SKB_CB(skb) ((struct emac_skb_cb *)(skb)->cb)
+#define EMAC_TX_TS_CB(skb) ((struct emac_tx_ts_cb *)(skb)->cb)
+#define EMAC_RSS_IDT_SIZE 256
+#define JUMBO_1KAH 0x4
+#define RXD_TH 0x100
+#define EMAC_TPD_LAST_FRAGMENT 0x80000000
+#define EMAC_TPD_TSTAMP_SAVE 0x80000000
+
+/* EMAC Errors in emac_rrd.word[3] */
+#define EMAC_RRD_L4F BIT(14)
+#define EMAC_RRD_IPF BIT(15)
+#define EMAC_RRD_CRC BIT(21)
+#define EMAC_RRD_FAE BIT(22)
+#define EMAC_RRD_TRN BIT(23)
+#define EMAC_RRD_RNT BIT(24)
+#define EMAC_RRD_INC BIT(25)
+#define EMAC_RRD_FOV BIT(29)
+#define EMAC_RRD_LEN BIT(30)
+
+/* Error bits that will result in a received frame being discarded */
+#define EMAC_RRD_ERROR (EMAC_RRD_IPF | EMAC_RRD_CRC | EMAC_RRD_FAE | \
+ EMAC_RRD_TRN | EMAC_RRD_RNT | EMAC_RRD_INC | \
+ EMAC_RRD_FOV | EMAC_RRD_LEN)
+#define EMAC_RRD_STATS_DW_IDX 3
+
+#define EMAC_RRD(RXQ, SIZE, IDX) ((RXQ)->rrd.v_addr + (SIZE * (IDX)))
+#define EMAC_RFD(RXQ, SIZE, IDX) ((RXQ)->rfd.v_addr + (SIZE * (IDX)))
+#define EMAC_TPD(TXQ, SIZE, IDX) ((TXQ)->tpd.v_addr + (SIZE * (IDX)))
+
+#define GET_RFD_BUFFER(RXQ, IDX) (&((RXQ)->rfd.rfbuff[(IDX)]))
+#define GET_TPD_BUFFER(RTQ, IDX) (&((RTQ)->tpd.tpbuff[(IDX)]))
+
+#define EMAC_TX_POLL_HWTXTSTAMP_THRESHOLD 8
+
+#define ISR_RX_PKT (\
+ RX_PKT_INT0 |\
+ RX_PKT_INT1 |\
+ RX_PKT_INT2 |\
+ RX_PKT_INT3)
+
+void emac_mac_multicast_addr_set(struct emac_adapter *adpt, u8 *addr)
+{
+ u32 crc32, bit, reg, mta;
+
+ /* Calculate the CRC of the MAC address */
+ crc32 = ether_crc(ETH_ALEN, addr);
+
+ /* The HASH Table is an array of 2 32-bit registers. It is
+ * treated like an array of 64 bits (BitArray[hash_value]).
+ * Use the upper 6 bits of the above CRC as the hash value.
+ */
+ reg = (crc32 >> 31) & 0x1;
+ bit = (crc32 >> 26) & 0x1F;
+
+ mta = readl(adpt->base + EMAC_HASH_TAB_REG0 + (reg << 2));
+ mta |= (0x1 << bit);
+ writel(mta, adpt->base + EMAC_HASH_TAB_REG0 + (reg << 2));
+}
+
+void emac_mac_multicast_addr_clear(struct emac_adapter *adpt)
+{
+ writel(0, adpt->base + EMAC_HASH_TAB_REG0);
+ writel(0, adpt->base + EMAC_HASH_TAB_REG1);
+}
+
+/* definitions for RSS */
+#define EMAC_RSS_KEY(_i, _type) \
+ (EMAC_RSS_KEY0 + ((_i) * sizeof(_type)))
+#define EMAC_RSS_TBL(_i, _type) \
+ (EMAC_IDT_TABLE0 + ((_i) * sizeof(_type)))
+
+/* Config MAC modes */
+void emac_mac_mode_config(struct emac_adapter *adpt)
+{
+ u32 mac;
+
+ mac = readl(adpt->base + EMAC_MAC_CTRL);
+
+ if (test_bit(EMAC_STATUS_VLANSTRIP_EN, &adpt->status))
+ mac |= VLAN_STRIP;
+ else
+ mac &= ~VLAN_STRIP;
+
+ if (test_bit(EMAC_STATUS_PROMISC_EN, &adpt->status))
+ mac |= PROM_MODE;
+ else
+ mac &= ~PROM_MODE;
+
+ if (test_bit(EMAC_STATUS_MULTIALL_EN, &adpt->status))
+ mac |= MULTI_ALL;
+ else
+ mac &= ~MULTI_ALL;
+
+ if (test_bit(EMAC_STATUS_LOOPBACK_EN, &adpt->status))
+ mac |= MAC_LP_EN;
+ else
+ mac &= ~MAC_LP_EN;
+
+ writel(mac, adpt->base + EMAC_MAC_CTRL);
+}
+
+/* Power Management */
+void emac_mac_pm(struct emac_adapter *adpt)
+{
+ u32 dma_mas, mac;
+
+ dma_mas = readl(adpt->base + EMAC_DMA_MAS_CTRL);
+ dma_mas &= ~LPW_CLK_SEL;
+ dma_mas |= LPW_STATE | LPW_CLK_SEL;
+
+ mac = readl(adpt->base + EMAC_MAC_CTRL);
+ mac &= ~(FULLD | RXEN | TXEN);
+ mac = (mac & ~SPEED_BMSK) |
+ (((u32)emac_mac_speed_10_100 << SPEED_SHFT) & SPEED_BMSK);
+
+ writel(dma_mas, adpt->base + EMAC_DMA_MAS_CTRL);
+ writel(mac, adpt->base + EMAC_MAC_CTRL);
+}
+
+/* Config descriptor rings */
+static void emac_mac_dma_rings_config(struct emac_adapter *adpt)
+{
+ static const unsigned int tpd_q_offset[] = {
+ EMAC_DESC_CTRL_8, EMAC_H1TPD_BASE_ADDR_LO,
+ EMAC_H2TPD_BASE_ADDR_LO, EMAC_H3TPD_BASE_ADDR_LO};
+ static const unsigned int rfd_q_offset[] = {
+ EMAC_DESC_CTRL_2, EMAC_DESC_CTRL_10,
+ EMAC_DESC_CTRL_12, EMAC_DESC_CTRL_13};
+ static const unsigned int rrd_q_offset[] = {
+ EMAC_DESC_CTRL_5, EMAC_DESC_CTRL_14,
+ EMAC_DESC_CTRL_15, EMAC_DESC_CTRL_16};
+
+ if (adpt->timestamp_en)
+ emac_reg_update32(adpt->csr + EMAC_EMAC_WRAPPER_CSR1,
+ 0, ENABLE_RRD_TIMESTAMP);
+
+ /* TPD (Transmit Packet Descriptor) */
+ writel(EMAC_DMA_ADDR_HI(adpt->tx_q.tpd.dma_addr),
+ adpt->base + EMAC_DESC_CTRL_1);
+
+ writel(EMAC_DMA_ADDR_LO(adpt->tx_q.tpd.dma_addr),
+ adpt->base + tpd_q_offset[0]);
+
+ writel(adpt->tx_q.tpd.count & TPD_RING_SIZE_BMSK,
+ adpt->base + EMAC_DESC_CTRL_9);
+
+ /* RFD (Receive Free Descriptor) & RRD (Receive Return Descriptor) */
+ writel(EMAC_DMA_ADDR_HI(adpt->rx_q.rfd.dma_addr),
+ adpt->base + EMAC_DESC_CTRL_0);
+
+ writel(EMAC_DMA_ADDR_LO(adpt->rx_q.rfd.dma_addr),
+ adpt->base + rfd_q_offset[0]);
+ writel(EMAC_DMA_ADDR_LO(adpt->rx_q.rrd.dma_addr),
+ adpt->base + rrd_q_offset[0]);
+
+ writel(adpt->rx_q.rfd.count & RFD_RING_SIZE_BMSK,
+ adpt->base + EMAC_DESC_CTRL_3);
+ writel(adpt->rx_q.rrd.count & RRD_RING_SIZE_BMSK,
+ adpt->base + EMAC_DESC_CTRL_6);
+
+ writel(adpt->rxbuf_size & RX_BUFFER_SIZE_BMSK,
+ adpt->base + EMAC_DESC_CTRL_4);
+
+ writel(0, adpt->base + EMAC_DESC_CTRL_11);
+
+ /* Load all of the base addresses above and ensure that triggering HW to
+ * read ring pointers is flushed
+ */
+ writel(1, adpt->base + EMAC_INTER_SRAM_PART9);
+}
+
+/* Config transmit parameters */
+static void emac_mac_tx_config(struct emac_adapter *adpt)
+{
+ u32 val;
+
+ writel((EMAC_MAX_TX_OFFLOAD_THRESH >> 3) &
+ JUMBO_TASK_OFFLOAD_THRESHOLD_BMSK, adpt->base + EMAC_TXQ_CTRL_1);
+
+ val = (adpt->tpd_burst << NUM_TPD_BURST_PREF_SHFT) &
+ NUM_TPD_BURST_PREF_BMSK;
+
+ val |= (TXQ_MODE | LS_8023_SP);
+ val |= (0x0100 << NUM_TXF_BURST_PREF_SHFT) &
+ NUM_TXF_BURST_PREF_BMSK;
+
+ writel(val, adpt->base + EMAC_TXQ_CTRL_0);
+ emac_reg_update32(adpt->base + EMAC_TXQ_CTRL_2,
+ (TXF_HWM_BMSK | TXF_LWM_BMSK), 0);
+}
+
+/* Config receive parameters */
+static void emac_mac_rx_config(struct emac_adapter *adpt)
+{
+ u32 val;
+
+ val = ((adpt->rfd_burst << NUM_RFD_BURST_PREF_SHFT) &
+ NUM_RFD_BURST_PREF_BMSK);
+ val |= (SP_IPV6 | CUT_THRU_EN);
+
+ writel(val, adpt->base + EMAC_RXQ_CTRL_0);
+
+ val = readl(adpt->base + EMAC_RXQ_CTRL_1);
+ val &= ~(JUMBO_1KAH_BMSK | RFD_PREF_LOW_THRESHOLD_BMSK |
+ RFD_PREF_UP_THRESHOLD_BMSK);
+ val |= (JUMBO_1KAH << JUMBO_1KAH_SHFT) |
+ (RFD_PREF_LOW_TH << RFD_PREF_LOW_THRESHOLD_SHFT) |
+ (RFD_PREF_UP_TH << RFD_PREF_UP_THRESHOLD_SHFT);
+ writel(val, adpt->base + EMAC_RXQ_CTRL_1);
+
+ val = readl(adpt->base + EMAC_RXQ_CTRL_2);
+ val &= ~(RXF_DOF_THRESHOLD_BMSK | RXF_UOF_THRESHOLD_BMSK);
+ val |= (RXF_DOF_THRESFHOLD << RXF_DOF_THRESHOLD_SHFT) |
+ (RXF_UOF_THRESFHOLD << RXF_UOF_THRESHOLD_SHFT);
+ writel(val, adpt->base + EMAC_RXQ_CTRL_2);
+
+ val = readl(adpt->base + EMAC_RXQ_CTRL_3);
+ val &= ~(RXD_TIMER_BMSK | RXD_THRESHOLD_BMSK);
+ val |= RXD_TH << RXD_THRESHOLD_SHFT;
+ writel(val, adpt->base + EMAC_RXQ_CTRL_3);
+}
+
+/* Config dma */
+static void emac_mac_dma_config(struct emac_adapter *adpt)
+{
+ u32 dma_ctrl;
+
+ dma_ctrl = DMAR_REQ_PRI;
+
+ switch (adpt->dma_order) {
+ case emac_dma_ord_in:
+ dma_ctrl |= IN_ORDER_MODE;
+ break;
+ case emac_dma_ord_enh:
+ dma_ctrl |= ENH_ORDER_MODE;
+ break;
+ case emac_dma_ord_out:
+ dma_ctrl |= OUT_ORDER_MODE;
+ break;
+ default:
+ break;
+ }
+
+ dma_ctrl |= (((u32)adpt->dmar_block) << REGRDBLEN_SHFT) &
+ REGRDBLEN_BMSK;
+ dma_ctrl |= (((u32)adpt->dmaw_block) << REGWRBLEN_SHFT) &
+ REGWRBLEN_BMSK;
+ dma_ctrl |= (((u32)adpt->dmar_dly_cnt) << DMAR_DLY_CNT_SHFT) &
+ DMAR_DLY_CNT_BMSK;
+ dma_ctrl |= (((u32)adpt->dmaw_dly_cnt) << DMAW_DLY_CNT_SHFT) &
+ DMAW_DLY_CNT_BMSK;
+
+ /* config DMA and ensure that configuration is flushed to HW */
+ writel(dma_ctrl, adpt->base + EMAC_DMA_CTRL);
+}
+
+void emac_mac_config(struct emac_adapter *adpt)
+{
+ u32 val;
+
+ emac_mac_addr_clear(adpt, adpt->mac_addr);
+
+ emac_mac_dma_rings_config(adpt);
+
+ writel(adpt->mtu + ETH_HLEN + VLAN_HLEN + ETH_FCS_LEN,
+ adpt->base + EMAC_MAX_FRAM_LEN_CTRL);
+
+ emac_mac_tx_config(adpt);
+ emac_mac_rx_config(adpt);
+ emac_mac_dma_config(adpt);
+
+ val = readl(adpt->base + EMAC_AXI_MAST_CTRL);
+ val &= ~(DATA_BYTE_SWAP | MAX_BOUND);
+ val |= MAX_BTYPE;
+ writel(val, adpt->base + EMAC_AXI_MAST_CTRL);
+ writel(0, adpt->base + EMAC_CLK_GATE_CTRL);
+ writel(RX_UNCPL_INT_EN, adpt->base + EMAC_MISC_CTRL);
+}
+
+void emac_mac_reset(struct emac_adapter *adpt)
+{
+ writel(0, adpt->base + EMAC_INT_MASK);
+ writel(DIS_INT, adpt->base + EMAC_INT_STATUS);
+
+ emac_mac_stop(adpt);
+
+ emac_reg_update32(adpt->base + EMAC_DMA_MAS_CTRL, 0, SOFT_RST);
+ usleep_range(100, 150); /* reset may take upto 100usec */
+
+ /* interrupt clear-on-read */
+ emac_reg_update32(adpt->base + EMAC_DMA_MAS_CTRL, 0, INT_RD_CLR_EN);
+}
+
+void emac_mac_start(struct emac_adapter *adpt)
+{
+ struct emac_phy *phy = &adpt->phy;
+ u32 mac, csr1;
+
+ /* enable tx queue */
+ emac_reg_update32(adpt->base + EMAC_TXQ_CTRL_0, 0, TXQ_EN);
+
+ /* enable rx queue */
+ emac_reg_update32(adpt->base + EMAC_RXQ_CTRL_0, 0, RXQ_EN);
+
+ /* enable mac control */
+ mac = readl(adpt->base + EMAC_MAC_CTRL);
+ csr1 = readl(adpt->csr + EMAC_EMAC_WRAPPER_CSR1);
+
+ mac |= TXEN | RXEN; /* enable RX/TX */
+
+ /* enable RX/TX Flow Control */
+ switch (phy->cur_fc_mode) {
+ case EMAC_FC_FULL:
+ mac |= (TXFC | RXFC);
+ break;
+ case EMAC_FC_RX_PAUSE:
+ mac |= RXFC;
+ break;
+ case EMAC_FC_TX_PAUSE:
+ mac |= TXFC;
+ break;
+ default:
+ break;
+ }
+
+ /* setup link speed */
+ mac &= ~SPEED_BMSK;
+ switch (phy->link_speed) {
+ case EMAC_LINK_SPEED_1GB_FULL:
+ mac |= ((emac_mac_speed_1000 << SPEED_SHFT) & SPEED_BMSK);
+ csr1 |= FREQ_MODE;
+ break;
+ default:
+ mac |= ((emac_mac_speed_10_100 << SPEED_SHFT) & SPEED_BMSK);
+ csr1 &= ~FREQ_MODE;
+ break;
+ }
+
+ switch (phy->link_speed) {
+ case EMAC_LINK_SPEED_1GB_FULL:
+ case EMAC_LINK_SPEED_100_FULL:
+ case EMAC_LINK_SPEED_10_FULL:
+ mac |= FULLD;
+ break;
+ default:
+ mac &= ~FULLD;
+ }
+
+ /* other parameters */
+ mac |= (CRCE | PCRCE);
+ mac |= ((adpt->preamble << PRLEN_SHFT) & PRLEN_BMSK);
+ mac |= BROAD_EN;
+ mac |= FLCHK;
+ mac &= ~RX_CHKSUM_EN;
+ mac &= ~(HUGEN | VLAN_STRIP | TPAUSE | SIMR | HUGE | MULTI_ALL |
+ DEBUG_MODE | SINGLE_PAUSE_MODE);
+
+ writel_relaxed(csr1, adpt->csr + EMAC_EMAC_WRAPPER_CSR1);
+
+ writel_relaxed(mac, adpt->base + EMAC_MAC_CTRL);
+
+ /* enable interrupt read clear, low power sleep mode and
+ * the irq moderators
+ */
+
+ writel_relaxed(adpt->irq_mod, adpt->base + EMAC_IRQ_MOD_TIM_INIT);
+ writel_relaxed(INT_RD_CLR_EN | LPW_MODE | IRQ_MODERATOR_EN |
+ IRQ_MODERATOR2_EN, adpt->base + EMAC_DMA_MAS_CTRL);
+
+ emac_mac_mode_config(adpt);
+
+ emac_reg_update32(adpt->base + EMAC_ATHR_HEADER_CTRL,
+ (HEADER_ENABLE | HEADER_CNT_EN), 0);
+
+ emac_reg_update32(adpt->csr + EMAC_EMAC_WRAPPER_CSR2, 0, WOL_EN);
+}
+
+void emac_mac_stop(struct emac_adapter *adpt)
+{
+ emac_reg_update32(adpt->base + EMAC_RXQ_CTRL_0, RXQ_EN, 0);
+ emac_reg_update32(adpt->base + EMAC_TXQ_CTRL_0, TXQ_EN, 0);
+ emac_reg_update32(adpt->base + EMAC_MAC_CTRL, (TXEN | RXEN), 0);
+ usleep_range(1000, 1050); /* stopping mac may take upto 1msec */
+}
+
+/* set MAC address */
+void emac_mac_addr_clear(struct emac_adapter *adpt, u8 *addr)
+{
+ u32 sta;
+
+ /* for example: 00-A0-C6-11-22-33
+ * 0<-->C6112233, 1<-->00A0.
+ */
+
+ /* low 32bit word */
+ sta = (((u32)addr[2]) << 24) | (((u32)addr[3]) << 16) |
+ (((u32)addr[4]) << 8) | (((u32)addr[5]));
+ writel(sta, adpt->base + EMAC_MAC_STA_ADDR0);
+
+ /* hight 32bit word */
+ sta = (((u32)addr[0]) << 8) | (((u32)addr[1]));
+ writel(sta, adpt->base + EMAC_MAC_STA_ADDR1);
+}
+
+/* Read one entry from the HW tx timestamp FIFO */
+static bool emac_mac_tx_ts_read(struct emac_adapter *adpt,
+ struct emac_tx_ts *ts)
+{
+ u32 ts_idx;
+
+ ts_idx = readl_relaxed(adpt->csr + EMAC_EMAC_WRAPPER_TX_TS_INX);
+
+ if (ts_idx & EMAC_WRAPPER_TX_TS_EMPTY)
+ return false;
+
+ ts->ns = readl_relaxed(adpt->csr + EMAC_EMAC_WRAPPER_TX_TS_LO);
+ ts->sec = readl_relaxed(adpt->csr + EMAC_EMAC_WRAPPER_TX_TS_HI);
+ ts->ts_idx = ts_idx & EMAC_WRAPPER_TX_TS_INX_BMSK;
+
+ return true;
+}
+
+/* Free all descriptors of given transmit queue */
+static void emac_tx_q_descs_free(struct emac_adapter *adpt)
+{
+ struct emac_tx_queue *tx_q = &adpt->tx_q;
+ size_t size;
+ int i;
+
+ /* ring already cleared, nothing to do */
+ if (!tx_q->tpd.tpbuff)
+ return;
+
+ for (i = 0; i < tx_q->tpd.count; i++) {
+ struct emac_buffer *tpbuf = GET_TPD_BUFFER(tx_q, i);
+
+ if (tpbuf->dma_addr) {
+ dma_unmap_single(adpt->netdev->dev.parent,
+ tpbuf->dma_addr, tpbuf->length,
+ DMA_TO_DEVICE);
+ tpbuf->dma_addr = 0;
+ }
+ if (tpbuf->skb) {
+ dev_kfree_skb_any(tpbuf->skb);
+ tpbuf->skb = NULL;
+ }
+ }
+
+ size = sizeof(struct emac_buffer) * tx_q->tpd.count;
+ memset(tx_q->tpd.tpbuff, 0, size);
+
+ /* clear the descriptor ring */
+ memset(tx_q->tpd.v_addr, 0, tx_q->tpd.size);
+
+ tx_q->tpd.consume_idx = 0;
+ tx_q->tpd.produce_idx = 0;
+}
+
+/* Free all descriptors of given receive queue */
+static void emac_rx_q_free_descs(struct emac_adapter *adpt)
+{
+ struct emac_rx_queue *rx_q = &adpt->rx_q;
+ struct device *dev = adpt->netdev->dev.parent;
+ size_t size;
+ int i;
+
+ /* ring already cleared, nothing to do */
+ if (!rx_q->rfd.rfbuff)
+ return;
+
+ for (i = 0; i < rx_q->rfd.count; i++) {
+ struct emac_buffer *rfbuf = GET_RFD_BUFFER(rx_q, i);
+
+ if (rfbuf->dma_addr) {
+ dma_unmap_single(dev, rfbuf->dma_addr, rfbuf->length,
+ DMA_FROM_DEVICE);
+ rfbuf->dma_addr = 0;
+ }
+ if (rfbuf->skb) {
+ dev_kfree_skb(rfbuf->skb);
+ rfbuf->skb = NULL;
+ }
+ }
+
+ size = sizeof(struct emac_buffer) * rx_q->rfd.count;
+ memset(rx_q->rfd.rfbuff, 0, size);
+
+ /* clear the descriptor rings */
+ memset(rx_q->rrd.v_addr, 0, rx_q->rrd.size);
+ rx_q->rrd.produce_idx = 0;
+ rx_q->rrd.consume_idx = 0;
+
+ memset(rx_q->rfd.v_addr, 0, rx_q->rfd.size);
+ rx_q->rfd.produce_idx = 0;
+ rx_q->rfd.consume_idx = 0;
+}
+
+/* Free all buffers associated with given transmit queue */
+static void emac_tx_q_bufs_free(struct emac_adapter *adpt)
+{
+ struct emac_tx_queue *tx_q = &adpt->tx_q;
+
+ emac_tx_q_descs_free(adpt);
+
+ kfree(tx_q->tpd.tpbuff);
+ tx_q->tpd.tpbuff = NULL;
+ tx_q->tpd.v_addr = NULL;
+ tx_q->tpd.dma_addr = 0;
+ tx_q->tpd.size = 0;
+}
+
+/* Allocate TX descriptor ring for the given transmit queue */
+static int emac_tx_q_desc_alloc(struct emac_adapter *adpt,
+ struct emac_tx_queue *tx_q)
+{
+ struct emac_ring_header *ring_header = &adpt->ring_header;
+ size_t size;
+
+ size = sizeof(struct emac_buffer) * tx_q->tpd.count;
+ tx_q->tpd.tpbuff = kzalloc(size, GFP_KERNEL);
+ if (!tx_q->tpd.tpbuff)
+ return -ENOMEM;
+
+ tx_q->tpd.size = tx_q->tpd.count * (adpt->tpd_size * 4);
+ tx_q->tpd.dma_addr = ring_header->dma_addr + ring_header->used;
+ tx_q->tpd.v_addr = ring_header->v_addr + ring_header->used;
+ ring_header->used += ALIGN(tx_q->tpd.size, 8);
+ tx_q->tpd.produce_idx = 0;
+ tx_q->tpd.consume_idx = 0;
+
+ return 0;
+}
+
+/* Free all buffers associated with given transmit queue */
+static void emac_rx_q_bufs_free(struct emac_adapter *adpt)
+{
+ struct emac_rx_queue *rx_q = &adpt->rx_q;
+
+ emac_rx_q_free_descs(adpt);
+
+ kfree(rx_q->rfd.rfbuff);
+ rx_q->rfd.rfbuff = NULL;
+
+ rx_q->rfd.v_addr = NULL;
+ rx_q->rfd.dma_addr = 0;
+ rx_q->rfd.size = 0;
+
+ rx_q->rrd.v_addr = NULL;
+ rx_q->rrd.dma_addr = 0;
+ rx_q->rrd.size = 0;
+}
+
+/* Allocate RX descriptor rings for the given receive queue */
+static int emac_rx_descs_alloc(struct emac_adapter *adpt)
+{
+ struct emac_rx_queue *rx_q = &adpt->rx_q;
+ struct emac_ring_header *ring_header = &adpt->ring_header;
+ unsigned long size;
+
+ size = sizeof(struct emac_buffer) * rx_q->rfd.count;
+ rx_q->rfd.rfbuff = kzalloc(size, GFP_KERNEL);
+ if (!rx_q->rfd.rfbuff)
+ return -ENOMEM;
+
+ rx_q->rrd.size = rx_q->rrd.count * (adpt->rrd_size * 4);
+ rx_q->rfd.size = rx_q->rfd.count * (adpt->rfd_size * 4);
+
+ rx_q->rrd.dma_addr = ring_header->dma_addr + ring_header->used;
+ rx_q->rrd.v_addr = ring_header->v_addr + ring_header->used;
+ ring_header->used += ALIGN(rx_q->rrd.size, 8);
+
+ rx_q->rfd.dma_addr = ring_header->dma_addr + ring_header->used;
+ rx_q->rfd.v_addr = ring_header->v_addr + ring_header->used;
+ ring_header->used += ALIGN(rx_q->rfd.size, 8);
+
+ rx_q->rrd.produce_idx = 0;
+ rx_q->rrd.consume_idx = 0;
+
+ rx_q->rfd.produce_idx = 0;
+ rx_q->rfd.consume_idx = 0;
+
+ return 0;
+}
+
+/* Allocate all TX and RX descriptor rings */
+int emac_mac_rx_tx_rings_alloc_all(struct emac_adapter *adpt)
+{
+ struct emac_ring_header *ring_header = &adpt->ring_header;
+ unsigned int num_tx_descs = adpt->tx_desc_cnt;
+ unsigned int num_rx_descs = adpt->rx_desc_cnt;
+ struct device *dev = adpt->netdev->dev.parent;
+ int ret;
+
+ adpt->tx_q.tpd.count = adpt->tx_desc_cnt;
+
+ adpt->rx_q.rrd.count = adpt->rx_desc_cnt;
+ adpt->rx_q.rfd.count = adpt->rx_desc_cnt;
+
+ /* Ring DMA buffer. Each ring may need up to 8 bytes for alignment,
+ * hence the additional padding bytes are allocated.
+ */
+ ring_header->size = num_tx_descs * (adpt->tpd_size * 4) +
+ num_rx_descs * (adpt->rfd_size * 4) +
+ num_rx_descs * (adpt->rrd_size * 4) +
+ 8 + 2 * 8; /* 8 byte per one Tx and two Rx rings */
+
+ ring_header->used = 0;
+ ring_header->v_addr = dma_alloc_coherent(dev, ring_header->size,
+ &ring_header->dma_addr,
+ GFP_KERNEL);
+ if (!ring_header->v_addr)
+ return -ENOMEM;
+
+ memset(ring_header->v_addr, 0, ring_header->size);
+ ring_header->used = ALIGN(ring_header->dma_addr, 8) -
+ ring_header->dma_addr;
+
+ ret = emac_tx_q_desc_alloc(adpt, &adpt->tx_q);
+ if (ret) {
+ netdev_err(adpt->netdev, "error: Tx Queue alloc failed\n");
+ goto err_alloc_tx;
+ }
+
+ ret = emac_rx_descs_alloc(adpt);
+ if (ret) {
+ netdev_err(adpt->netdev, "error: Rx Queue alloc failed\n");
+ goto err_alloc_rx;
+ }
+
+ return 0;
+
+err_alloc_rx:
+ emac_tx_q_bufs_free(adpt);
+err_alloc_tx:
+ dma_free_coherent(dev, ring_header->size,
+ ring_header->v_addr, ring_header->dma_addr);
+
+ ring_header->v_addr = NULL;
+ ring_header->dma_addr = 0;
+ ring_header->size = 0;
+ ring_header->used = 0;
+
+ return ret;
+}
+
+/* Free all TX and RX descriptor rings */
+void emac_mac_rx_tx_rings_free_all(struct emac_adapter *adpt)
+{
+ struct emac_ring_header *ring_header = &adpt->ring_header;
+ struct device *dev = adpt->netdev->dev.parent;
+
+ emac_tx_q_bufs_free(adpt);
+ emac_rx_q_bufs_free(adpt);
+
+ dma_free_coherent(dev, ring_header->size,
+ ring_header->v_addr, ring_header->dma_addr);
+
+ ring_header->v_addr = NULL;
+ ring_header->dma_addr = 0;
+ ring_header->size = 0;
+ ring_header->used = 0;
+}
+
+/* Initialize descriptor rings */
+static void emac_mac_rx_tx_ring_reset_all(struct emac_adapter *adpt)
+{
+ int i;
+
+ adpt->tx_q.tpd.produce_idx = 0;
+ adpt->tx_q.tpd.consume_idx = 0;
+ for (i = 0; i < adpt->tx_q.tpd.count; i++)
+ adpt->tx_q.tpd.tpbuff[i].dma_addr = 0;
+
+ adpt->rx_q.rrd.produce_idx = 0;
+ adpt->rx_q.rrd.consume_idx = 0;
+ adpt->rx_q.rfd.produce_idx = 0;
+ adpt->rx_q.rfd.consume_idx = 0;
+ for (i = 0; i < adpt->rx_q.rfd.count; i++)
+ adpt->rx_q.rfd.rfbuff[i].dma_addr = 0;
+}
+
+/* Produce new receive free descriptor */
+static void emac_mac_rx_rfd_create(struct emac_adapter *adpt,
+ struct emac_rx_queue *rx_q,
+ union emac_rfd *rfd)
+{
+ u32 *hw_rfd = EMAC_RFD(rx_q, adpt->rfd_size,
+ rx_q->rfd.produce_idx);
+
+ *(hw_rfd++) = rfd->word[0];
+ *hw_rfd = rfd->word[1];
+
+ if (++rx_q->rfd.produce_idx == rx_q->rfd.count)
+ rx_q->rfd.produce_idx = 0;
+}
+
+/* Fill up receive queue's RFD with preallocated receive buffers */
+static int emac_mac_rx_descs_refill(struct emac_adapter *adpt,
+ struct emac_rx_queue *rx_q)
+{
+ struct emac_buffer *curr_rxbuf;
+ struct emac_buffer *next_rxbuf;
+ union emac_rfd rfd;
+ struct sk_buff *skb;
+ void *skb_data = NULL;
+ int count = 0;
+ u32 next_produce_idx;
+
+ next_produce_idx = rx_q->rfd.produce_idx;
+ if (++next_produce_idx == rx_q->rfd.count)
+ next_produce_idx = 0;
+ curr_rxbuf = GET_RFD_BUFFER(rx_q, rx_q->rfd.produce_idx);
+ next_rxbuf = GET_RFD_BUFFER(rx_q, next_produce_idx);
+
+ /* this always has a blank rx_buffer*/
+ while (!next_rxbuf->dma_addr) {
+ skb = dev_alloc_skb(adpt->rxbuf_size + NET_IP_ALIGN);
+ if (!skb)
+ break;
+
+ /* Make buffer alignment 2 beyond a 16 byte boundary
+ * this will result in a 16 byte aligned IP header after
+ * the 14 byte MAC header is removed
+ */
+ skb_reserve(skb, NET_IP_ALIGN);
+ skb_data = skb->data;
+ curr_rxbuf->skb = skb;
+ curr_rxbuf->length = adpt->rxbuf_size;
+ curr_rxbuf->dma_addr = dma_map_single(adpt->netdev->dev.parent,
+ skb_data,
+ curr_rxbuf->length,
+ DMA_FROM_DEVICE);
+ rfd.addr = curr_rxbuf->dma_addr;
+ emac_mac_rx_rfd_create(adpt, rx_q, &rfd);
+ next_produce_idx = rx_q->rfd.produce_idx;
+ if (++next_produce_idx == rx_q->rfd.count)
+ next_produce_idx = 0;
+
+ curr_rxbuf = GET_RFD_BUFFER(rx_q, rx_q->rfd.produce_idx);
+ next_rxbuf = GET_RFD_BUFFER(rx_q, next_produce_idx);
+ count++;
+ }
+
+ if (count) {
+ u32 prod_idx = (rx_q->rfd.produce_idx << rx_q->produce_shift) &
+ rx_q->produce_mask;
+ emac_reg_update32(adpt->base + rx_q->produce_reg,
+ rx_q->produce_mask, prod_idx);
+ }
+
+ return count;
+}
+
+/* Bringup the interface/HW */
+int emac_mac_up(struct emac_adapter *adpt)
+{
+ struct emac_phy *phy = &adpt->phy;
+ struct emac_irq *irq = &adpt->irq;
+
+ struct net_device *netdev = adpt->netdev;
+ int ret = 0;
+ int i;
+
+ emac_mac_rx_tx_ring_reset_all(adpt);
+ emac_rx_mode_set(netdev);
+
+ emac_mac_config(adpt);
+
+ ret = emac_sgmii_up(adpt);
+
+ if (ret)
+ return ret;
+
+ for (i = 0; phy->uses_gpios && i < EMAC_GPIO_CNT; i++) {
+ ret = gpio_request(adpt->gpio[i], emac_gpio_name[i]);
+ if (ret) {
+ netdev_err(adpt->netdev,
+ "error:%d on gpio_request(%d:%s)\n",
+ ret, adpt->gpio[i], emac_gpio_name[i]);
+ while (--i >= 0)
+ gpio_free(adpt->gpio[i]);
+ goto err_request_gpio;
+ }
+ }
+
+ ret = request_irq(irq->irq, emac_isr, 0, EMAC_MAC_IRQ_RES, irq);
+ if (ret) {
+ netdev_err(adpt->netdev,
+ "error:%d on request_irq(%d:%s flags:0)\n", ret,
+ irq->irq, EMAC_MAC_IRQ_RES);
+ goto err_request_irq;
+ }
+
+ emac_mac_rx_descs_refill(adpt, &adpt->rx_q);
+
+ napi_enable(&adpt->rx_q.napi);
+
+ /* enable mac irq */
+ writel(~DIS_INT, adpt->base + EMAC_INT_STATUS);
+ writel(adpt->irq.mask, adpt->base + EMAC_INT_MASK);
+
+ netif_start_queue(netdev);
+ clear_bit(EMAC_STATUS_DOWN, &adpt->status);
+
+ /* check link status */
+ set_bit(EMAC_STATUS_TASK_LSC_REQ, &adpt->status);
+ adpt->link_chk_timeout = jiffies + EMAC_TRY_LINK_TIMEOUT;
+ mod_timer(&adpt->timers, jiffies);
+
+ return ret;
+
+err_request_irq:
+ for (i = 0; adpt->phy.uses_gpios && i < EMAC_GPIO_CNT; i++)
+ gpio_free(adpt->gpio[i]);
+err_request_gpio:
+ emac_sgmii_down(adpt);
+ return ret;
+}
+
+/* Bring down the interface/HW */
+void emac_mac_down(struct emac_adapter *adpt, bool reset)
+{
+ struct net_device *netdev = adpt->netdev;
+ struct emac_phy *phy = &adpt->phy;
+
+ unsigned long flags;
+ int i;
+
+ set_bit(EMAC_STATUS_DOWN, &adpt->status);
+
+ netif_stop_queue(netdev);
+ netif_carrier_off(netdev);
+
+ /* disable mac irq */
+ writel(DIS_INT, adpt->base + EMAC_INT_STATUS);
+ writel(0, adpt->base + EMAC_INT_MASK);
+ synchronize_irq(adpt->irq.irq);
+
+ napi_disable(&adpt->rx_q.napi);
+
+ emac_sgmii_down(adpt);
+
+ free_irq(adpt->irq.irq, &adpt->irq);
+
+ for (i = 0; phy->uses_gpios && i < EMAC_GPIO_CNT; i++)
+ gpio_free(adpt->gpio[i]);
+
+ clear_bit(EMAC_STATUS_TASK_LSC_REQ, &adpt->status);
+ clear_bit(EMAC_STATUS_TASK_REINIT_REQ, &adpt->status);
+ clear_bit(EMAC_STATUS_TASK_CHK_SGMII_REQ, &adpt->status);
+ del_timer_sync(&adpt->timers);
+
+ cancel_work_sync(&adpt->tx_ts_task);
+ spin_lock_irqsave(&adpt->tx_ts_lock, flags);
+ __skb_queue_purge(&adpt->tx_ts_pending_queue);
+ __skb_queue_purge(&adpt->tx_ts_ready_queue);
+ spin_unlock_irqrestore(&adpt->tx_ts_lock, flags);
+
+ if (reset)
+ emac_mac_reset(adpt);
+
+ pm_runtime_put_noidle(netdev->dev.parent);
+ phy->link_speed = EMAC_LINK_SPEED_UNKNOWN;
+ emac_tx_q_descs_free(adpt);
+ netdev_reset_queue(adpt->netdev);
+ emac_rx_q_free_descs(adpt);
+}
+
+/* Consume next received packet descriptor */
+static bool emac_rx_process_rrd(struct emac_adapter *adpt,
+ struct emac_rx_queue *rx_q,
+ struct emac_rrd *rrd)
+{
+ u32 *hw_rrd = EMAC_RRD(rx_q, adpt->rrd_size,
+ rx_q->rrd.consume_idx);
+
+ /* If time stamping is enabled, it will be added in the beginning of
+ * the hw rrd (hw_rrd). In sw rrd (rrd), 32bit words 4 & 5 are reserved
+ * for the time stamp; hence the conversion.
+ * Also, read the rrd word with update flag first; read rest of rrd
+ * only if update flag is set.
+ */
+ if (adpt->timestamp_en)
+ rrd->word[3] = *(hw_rrd + 5);
+ else
+ rrd->word[3] = *(hw_rrd + 3);
+
+ if (!RRD_UPDT(rrd))
+ return false;
+
+ if (adpt->timestamp_en) {
+ rrd->word[4] = *(hw_rrd++);
+ rrd->word[5] = *(hw_rrd++);
+ } else {
+ rrd->word[4] = 0;
+ rrd->word[5] = 0;
+ }
+
+ rrd->word[0] = *(hw_rrd++);
+ rrd->word[1] = *(hw_rrd++);
+ rrd->word[2] = *(hw_rrd++);
+
+ if (unlikely(RRD_NOR(rrd) != 1)) {
+ netdev_err(adpt->netdev,
+ "error: multi-RFD not support yet! nor:%lu\n",
+ RRD_NOR(rrd));
+ }
+
+ /* mark rrd as processed */
+ RRD_UPDT_SET(rrd, 0);
+ *hw_rrd = rrd->word[3];
+
+ if (++rx_q->rrd.consume_idx == rx_q->rrd.count)
+ rx_q->rrd.consume_idx = 0;
+
+ return true;
+}
+
+/* Produce new transmit descriptor */
+static bool emac_tx_tpd_create(struct emac_adapter *adpt,
+ struct emac_tx_queue *tx_q, struct emac_tpd *tpd)
+{
+ u32 *hw_tpd;
+
+ tx_q->tpd.last_produce_idx = tx_q->tpd.produce_idx;
+ hw_tpd = EMAC_TPD(tx_q, adpt->tpd_size, tx_q->tpd.produce_idx);
+
+ if (++tx_q->tpd.produce_idx == tx_q->tpd.count)
+ tx_q->tpd.produce_idx = 0;
+
+ *(hw_tpd++) = tpd->word[0];
+ *(hw_tpd++) = tpd->word[1];
+ *(hw_tpd++) = tpd->word[2];
+ *hw_tpd = tpd->word[3];
+
+ return true;
+}
+
+/* Mark the last transmit descriptor as such (for the transmit packet) */
+static void emac_tx_tpd_mark_last(struct emac_adapter *adpt,
+ struct emac_tx_queue *tx_q)
+{
+ u32 tmp_tpd;
+ u32 *hw_tpd = EMAC_TPD(tx_q, adpt->tpd_size,
+ tx_q->tpd.last_produce_idx);
+
+ tmp_tpd = *(hw_tpd + 1);
+ tmp_tpd |= EMAC_TPD_LAST_FRAGMENT;
+ *(hw_tpd + 1) = tmp_tpd;
+}
+
+void emac_tx_tpd_ts_save(struct emac_adapter *adpt, struct emac_tx_queue *tx_q)
+{
+ u32 tmp_tpd;
+ u32 *hw_tpd = EMAC_TPD(tx_q, adpt->tpd_size,
+ tx_q->tpd.last_produce_idx);
+
+ tmp_tpd = *(hw_tpd + 3);
+ tmp_tpd |= EMAC_TPD_TSTAMP_SAVE;
+ *(hw_tpd + 3) = tmp_tpd;
+}
+
+static void emac_rx_rfd_clean(struct emac_rx_queue *rx_q,
+ struct emac_rrd *rrd)
+{
+ struct emac_buffer *rfbuf = rx_q->rfd.rfbuff;
+ u32 consume_idx = RRD_SI(rrd);
+ int i;
+
+ for (i = 0; i < RRD_NOR(rrd); i++) {
+ rfbuf[consume_idx].skb = NULL;
+ if (++consume_idx == rx_q->rfd.count)
+ consume_idx = 0;
+ }
+
+ rx_q->rfd.consume_idx = consume_idx;
+ rx_q->rfd.process_idx = consume_idx;
+}
+
+/* proper lock must be acquired before polling */
+static void emac_tx_ts_poll(struct emac_adapter *adpt)
+{
+ struct sk_buff_head *pending_q = &adpt->tx_ts_pending_queue;
+ struct sk_buff_head *q = &adpt->tx_ts_ready_queue;
+ struct sk_buff *skb, *skb_tmp;
+ struct emac_tx_ts tx_ts;
+
+ while (emac_mac_tx_ts_read(adpt, &tx_ts)) {
+ bool found = false;
+
+ adpt->tx_ts_stats.rx++;
+
+ skb_queue_walk_safe(pending_q, skb, skb_tmp) {
+ if (EMAC_SKB_CB(skb)->tpd_idx == tx_ts.ts_idx) {
+ struct sk_buff *pskb;
+
+ EMAC_TX_TS_CB(skb)->sec = tx_ts.sec;
+ EMAC_TX_TS_CB(skb)->ns = tx_ts.ns;
+ /* the tx timestamps for all the pending
+ * packets before this one are lost
+ */
+ while ((pskb = __skb_dequeue(pending_q))
+ != skb) {
+ EMAC_TX_TS_CB(pskb)->sec = 0;
+ EMAC_TX_TS_CB(pskb)->ns = 0;
+ __skb_queue_tail(q, pskb);
+ adpt->tx_ts_stats.lost++;
+ }
+ __skb_queue_tail(q, skb);
+ found = true;
+ break;
+ }
+ }
+
+ if (!found) {
+ netif_dbg(adpt, tx_done, adpt->netdev,
+ "no entry(tpd=%d) found, drop tx timestamp\n",
+ tx_ts.ts_idx);
+ adpt->tx_ts_stats.drop++;
+ }
+ }
+
+ skb_queue_walk_safe(pending_q, skb, skb_tmp) {
+ /* No packet after this one expires */
+ if (time_is_after_jiffies(EMAC_SKB_CB(skb)->jiffies +
+ msecs_to_jiffies(100)))
+ break;
+ adpt->tx_ts_stats.timeout++;
+ netif_dbg(adpt, tx_done, adpt->netdev,
+ "tx timestamp timeout: tpd_idx=%d\n",
+ EMAC_SKB_CB(skb)->tpd_idx);
+
+ __skb_unlink(skb, pending_q);
+ EMAC_TX_TS_CB(skb)->sec = 0;
+ EMAC_TX_TS_CB(skb)->ns = 0;
+ __skb_queue_tail(q, skb);
+ }
+}
+
+static void emac_schedule_tx_ts_task(struct emac_adapter *adpt)
+{
+ if (test_bit(EMAC_STATUS_DOWN, &adpt->status))
+ return;
+
+ if (schedule_work(&adpt->tx_ts_task))
+ adpt->tx_ts_stats.sched++;
+}
+
+void emac_mac_tx_ts_periodic_routine(struct work_struct *work)
+{
+ struct emac_adapter *adpt = container_of(work, struct emac_adapter,
+ tx_ts_task);
+ struct sk_buff *skb;
+ struct sk_buff_head q;
+ unsigned long flags;
+
+ adpt->tx_ts_stats.poll++;
+
+ __skb_queue_head_init(&q);
+
+ while (1) {
+ spin_lock_irqsave(&adpt->tx_ts_lock, flags);
+ if (adpt->tx_ts_pending_queue.qlen)
+ emac_tx_ts_poll(adpt);
+ skb_queue_splice_tail_init(&adpt->tx_ts_ready_queue, &q);
+ spin_unlock_irqrestore(&adpt->tx_ts_lock, flags);
+
+ if (!q.qlen)
+ break;
+
+ while ((skb = __skb_dequeue(&q))) {
+ struct emac_tx_ts_cb *cb = EMAC_TX_TS_CB(skb);
+
+ if (cb->sec || cb->ns) {
+ struct skb_shared_hwtstamps ts;
+
+ ts.hwtstamp = ktime_set(cb->sec, cb->ns);
+ skb_tstamp_tx(skb, &ts);
+ adpt->tx_ts_stats.deliver++;
+ }
+ dev_kfree_skb_any(skb);
+ }
+ }
+
+ if (adpt->tx_ts_pending_queue.qlen)
+ emac_schedule_tx_ts_task(adpt);
+}
+
+/* Push the received skb to upper layers */
+static void emac_receive_skb(struct emac_rx_queue *rx_q,
+ struct sk_buff *skb,
+ u16 vlan_tag, bool vlan_flag)
+{
+ if (vlan_flag) {
+ u16 vlan;
+
+ EMAC_TAG_TO_VLAN(vlan_tag, vlan);
+ __vlan_hwaccel_put_tag(skb, htons(ETH_P_8021Q), vlan);
+ }
+
+ napi_gro_receive(&rx_q->napi, skb);
+}
+
+/* Process receive event */
+void emac_mac_rx_process(struct emac_adapter *adpt, struct emac_rx_queue *rx_q,
+ int *num_pkts, int max_pkts)
+{
+ struct net_device *netdev = adpt->netdev;
+
+ struct emac_rrd rrd;
+ struct emac_buffer *rfbuf;
+ struct sk_buff *skb;
+
+ u32 hw_consume_idx, num_consume_pkts;
+ unsigned int count = 0;
+ u32 proc_idx;
+ u32 reg = readl_relaxed(adpt->base + rx_q->consume_reg);
+
+ hw_consume_idx = (reg & rx_q->consume_mask) >> rx_q->consume_shift;
+ num_consume_pkts = (hw_consume_idx >= rx_q->rrd.consume_idx) ?
+ (hw_consume_idx - rx_q->rrd.consume_idx) :
+ (hw_consume_idx + rx_q->rrd.count - rx_q->rrd.consume_idx);
+
+ do {
+ if (!num_consume_pkts)
+ break;
+
+ if (!emac_rx_process_rrd(adpt, rx_q, &rrd))
+ break;
+
+ if (likely(RRD_NOR(&rrd) == 1)) {
+ /* good receive */
+ rfbuf = GET_RFD_BUFFER(rx_q, RRD_SI(&rrd));
+ dma_unmap_single(adpt->netdev->dev.parent,
+ rfbuf->dma_addr, rfbuf->length,
+ DMA_FROM_DEVICE);
+ rfbuf->dma_addr = 0;
+ skb = rfbuf->skb;
+ } else {
+ netdev_err(adpt->netdev,
+ "error: multi-RFD not support yet!\n");
+ break;
+ }
+ emac_rx_rfd_clean(rx_q, &rrd);
+ num_consume_pkts--;
+ count++;
+
+ /* Due to a HW issue in L4 check sum detection (UDP/TCP frags
+ * with DF set are marked as error), drop packets based on the
+ * error mask rather than the summary bit (ignoring L4F errors)
+ */
+ if (rrd.word[EMAC_RRD_STATS_DW_IDX] & EMAC_RRD_ERROR) {
+ netif_dbg(adpt, rx_status, adpt->netdev,
+ "Drop error packet[RRD: 0x%x:0x%x:0x%x:0x%x]\n",
+ rrd.word[0], rrd.word[1],
+ rrd.word[2], rrd.word[3]);
+
+ dev_kfree_skb(skb);
+ continue;
+ }
+
+ skb_put(skb, RRD_PKT_SIZE(&rrd) - ETH_FCS_LEN);
+ skb->dev = netdev;
+ skb->protocol = eth_type_trans(skb, skb->dev);
+ if (netdev->features & NETIF_F_RXCSUM)
+ skb->ip_summed = (RRD_L4F(&rrd) ?
+ CHECKSUM_NONE : CHECKSUM_UNNECESSARY);
+ else
+ skb_checksum_none_assert(skb);
+
+ if (test_bit(EMAC_STATUS_TS_RX_EN, &adpt->status)) {
+ struct skb_shared_hwtstamps *hwts = skb_hwtstamps(skb);
+
+ hwts->hwtstamp = ktime_set(RRD_TS_HI(&rrd),
+ RRD_TS_LOW(&rrd));
+ }
+
+ emac_receive_skb(rx_q, skb, (u16)RRD_CVALN_TAG(&rrd),
+ (bool)RRD_CVTAG(&rrd));
+
+ netdev->last_rx = jiffies;
+ (*num_pkts)++;
+ } while (*num_pkts < max_pkts);
+
+ if (count) {
+ proc_idx = (rx_q->rfd.process_idx << rx_q->process_shft) &
+ rx_q->process_mask;
+ emac_reg_update32(adpt->base + rx_q->process_reg,
+ rx_q->process_mask, proc_idx);
+ emac_mac_rx_descs_refill(adpt, rx_q);
+ }
+}
+
+/* Process transmit event */
+void emac_mac_tx_process(struct emac_adapter *adpt, struct emac_tx_queue *tx_q)
+{
+ struct emac_buffer *tpbuf;
+ u32 hw_consume_idx;
+ u32 pkts_compl = 0, bytes_compl = 0;
+ u32 reg = readl_relaxed(adpt->base + tx_q->consume_reg);
+
+ hw_consume_idx = (reg & tx_q->consume_mask) >> tx_q->consume_shift;
+
+ while (tx_q->tpd.consume_idx != hw_consume_idx) {
+ tpbuf = GET_TPD_BUFFER(tx_q, tx_q->tpd.consume_idx);
+ if (tpbuf->dma_addr) {
+ dma_unmap_single(adpt->netdev->dev.parent,
+ tpbuf->dma_addr, tpbuf->length,
+ DMA_TO_DEVICE);
+ tpbuf->dma_addr = 0;
+ }
+
+ if (tpbuf->skb) {
+ pkts_compl++;
+ bytes_compl += tpbuf->skb->len;
+ dev_kfree_skb_irq(tpbuf->skb);
+ tpbuf->skb = NULL;
+ }
+
+ if (++tx_q->tpd.consume_idx == tx_q->tpd.count)
+ tx_q->tpd.consume_idx = 0;
+ }
+
+ if (pkts_compl || bytes_compl)
+ netdev_completed_queue(adpt->netdev, pkts_compl, bytes_compl);
+}
+
+/* Initialize all queue data structures */
+void emac_mac_rx_tx_ring_init_all(struct platform_device *pdev,
+ struct emac_adapter *adpt)
+{
+ adpt->rx_q.netdev = adpt->netdev;
+
+ adpt->rx_q.produce_reg = EMAC_MAILBOX_0;
+ adpt->rx_q.produce_mask = RFD0_PROD_IDX_BMSK;
+ adpt->rx_q.produce_shift = RFD0_PROD_IDX_SHFT;
+
+ adpt->rx_q.process_reg = EMAC_MAILBOX_0;
+ adpt->rx_q.process_mask = RFD0_PROC_IDX_BMSK;
+ adpt->rx_q.process_shft = RFD0_PROC_IDX_SHFT;
+
+ adpt->rx_q.consume_reg = EMAC_MAILBOX_3;
+ adpt->rx_q.consume_mask = RFD0_CONS_IDX_BMSK;
+ adpt->rx_q.consume_shift = RFD0_CONS_IDX_SHFT;
+
+ adpt->rx_q.irq = &adpt->irq;
+ adpt->rx_q.intr = adpt->irq.mask & ISR_RX_PKT;
+
+ adpt->tx_q.produce_reg = EMAC_MAILBOX_15;
+ adpt->tx_q.produce_mask = NTPD_PROD_IDX_BMSK;
+ adpt->tx_q.produce_shift = NTPD_PROD_IDX_SHFT;
+
+ adpt->tx_q.consume_reg = EMAC_MAILBOX_2;
+ adpt->tx_q.consume_mask = NTPD_CONS_IDX_BMSK;
+ adpt->tx_q.consume_shift = NTPD_CONS_IDX_SHFT;
+}
+
+/* get the number of free transmit descriptors */
+static u32 emac_tpd_num_free_descs(struct emac_tx_queue *tx_q)
+{
+ u32 produce_idx = tx_q->tpd.produce_idx;
+ u32 consume_idx = tx_q->tpd.consume_idx;
+
+ return (consume_idx > produce_idx) ?
+ (consume_idx - produce_idx - 1) :
+ (tx_q->tpd.count + consume_idx - produce_idx - 1);
+}
+
+/* Check if enough transmit descriptors are available */
+static bool emac_tx_has_enough_descs(struct emac_tx_queue *tx_q,
+ const struct sk_buff *skb)
+{
+ u32 num_required = 1;
+ int i;
+ u16 proto_hdr_len = 0;
+
+ if (skb_is_gso(skb)) {
+ proto_hdr_len = skb_transport_offset(skb) + tcp_hdrlen(skb);
+ if (proto_hdr_len < skb_headlen(skb))
+ num_required++;
+ if (skb_shinfo(skb)->gso_type & SKB_GSO_TCPV6)
+ num_required++;
+ }
+
+ for (i = 0; i < skb_shinfo(skb)->nr_frags; i++)
+ num_required++;
+
+ return num_required < emac_tpd_num_free_descs(tx_q);
+}
+
+/* Fill up transmit descriptors with TSO and Checksum offload information */
+static int emac_tso_csum(struct emac_adapter *adpt,
+ struct emac_tx_queue *tx_q,
+ struct sk_buff *skb,
+ struct emac_tpd *tpd)
+{
+ u8 hdr_len;
+ int ret;
+
+ if (skb_is_gso(skb)) {
+ if (skb_header_cloned(skb)) {
+ ret = pskb_expand_head(skb, 0, 0, GFP_ATOMIC);
+ if (unlikely(ret))
+ return ret;
+ }
+
+ if (skb->protocol == htons(ETH_P_IP)) {
+ u32 pkt_len = ((unsigned char *)ip_hdr(skb) - skb->data)
+ + ntohs(ip_hdr(skb)->tot_len);
+ if (skb->len > pkt_len)
+ pskb_trim(skb, pkt_len);
+ }
+
+ hdr_len = skb_transport_offset(skb) + tcp_hdrlen(skb);
+ if (unlikely(skb->len == hdr_len)) {
+ /* we only need to do csum */
+ netif_warn(adpt, tx_err, adpt->netdev,
+ "tso not needed for packet with 0 data\n");
+ goto do_csum;
+ }
+
+ if (skb_shinfo(skb)->gso_type & SKB_GSO_TCPV4) {
+ ip_hdr(skb)->check = 0;
+ tcp_hdr(skb)->check = ~csum_tcpudp_magic(
+ ip_hdr(skb)->saddr,
+ ip_hdr(skb)->daddr,
+ 0, IPPROTO_TCP, 0);
+ TPD_IPV4_SET(tpd, 1);
+ }
+
+ if (skb_shinfo(skb)->gso_type & SKB_GSO_TCPV6) {
+ /* ipv6 tso need an extra tpd */
+ struct emac_tpd extra_tpd;
+
+ memset(tpd, 0, sizeof(*tpd));
+ memset(&extra_tpd, 0, sizeof(extra_tpd));
+
+ ipv6_hdr(skb)->payload_len = 0;
+ tcp_hdr(skb)->check = ~csum_ipv6_magic(
+ &ipv6_hdr(skb)->saddr,
+ &ipv6_hdr(skb)->daddr,
+ 0, IPPROTO_TCP, 0);
+ TPD_PKT_LEN_SET(&extra_tpd, skb->len);
+ TPD_LSO_SET(&extra_tpd, 1);
+ TPD_LSOV_SET(&extra_tpd, 1);
+ emac_tx_tpd_create(adpt, tx_q, &extra_tpd);
+ TPD_LSOV_SET(tpd, 1);
+ }
+
+ TPD_LSO_SET(tpd, 1);
+ TPD_TCPHDR_OFFSET_SET(tpd, skb_transport_offset(skb));
+ TPD_MSS_SET(tpd, skb_shinfo(skb)->gso_size);
+ return 0;
+ }
+
+do_csum:
+ if (likely(skb->ip_summed == CHECKSUM_PARTIAL)) {
+ u8 css, cso;
+
+ cso = skb_transport_offset(skb);
+ if (unlikely(cso & 0x1)) {
+ netdev_err(adpt->netdev,
+ "error: payload offset should be even\n");
+ return -EINVAL;
+ }
+ css = cso + skb->csum_offset;
+
+ TPD_PAYLOAD_OFFSET_SET(tpd, cso >> 1);
+ TPD_CXSUM_OFFSET_SET(tpd, css >> 1);
+ TPD_CSX_SET(tpd, 1);
+ }
+
+ return 0;
+}
+
+/* Fill up transmit descriptors */
+static void emac_tx_fill_tpd(struct emac_adapter *adpt,
+ struct emac_tx_queue *tx_q, struct sk_buff *skb,
+ struct emac_tpd *tpd)
+{
+ struct emac_buffer *tpbuf = NULL;
+ u16 nr_frags = skb_shinfo(skb)->nr_frags;
+ u32 len = skb_headlen(skb);
+ u16 map_len = 0;
+ u16 mapped_len = 0;
+ u16 hdr_len = 0;
+ int i;
+
+ /* if Large Segment Offload is (in TCP Segmentation Offload struct) */
+ if (TPD_LSO(tpd)) {
+ hdr_len = skb_transport_offset(skb) + tcp_hdrlen(skb);
+ map_len = hdr_len;
+
+ tpbuf = GET_TPD_BUFFER(tx_q, tx_q->tpd.produce_idx);
+ tpbuf->length = map_len;
+ tpbuf->dma_addr = dma_map_single(adpt->netdev->dev.parent,
+ skb->data, hdr_len,
+ DMA_TO_DEVICE);
+ mapped_len += map_len;
+ TPD_BUFFER_ADDR_L_SET(tpd, EMAC_DMA_ADDR_LO(tpbuf->dma_addr));
+ TPD_BUFFER_ADDR_H_SET(tpd, EMAC_DMA_ADDR_HI(tpbuf->dma_addr));
+ TPD_BUF_LEN_SET(tpd, tpbuf->length);
+ emac_tx_tpd_create(adpt, tx_q, tpd);
+ }
+
+ if (mapped_len < len) {
+ tpbuf = GET_TPD_BUFFER(tx_q, tx_q->tpd.produce_idx);
+ tpbuf->length = len - mapped_len;
+ tpbuf->dma_addr = dma_map_single(adpt->netdev->dev.parent,
+ skb->data + mapped_len,
+ tpbuf->length, DMA_TO_DEVICE);
+ TPD_BUFFER_ADDR_L_SET(tpd, EMAC_DMA_ADDR_LO(tpbuf->dma_addr));
+ TPD_BUFFER_ADDR_H_SET(tpd, EMAC_DMA_ADDR_HI(tpbuf->dma_addr));
+ TPD_BUF_LEN_SET(tpd, tpbuf->length);
+ emac_tx_tpd_create(adpt, tx_q, tpd);
+ }
+
+ for (i = 0; i < nr_frags; i++) {
+ struct skb_frag_struct *frag;
+
+ frag = &skb_shinfo(skb)->frags[i];
+
+ tpbuf = GET_TPD_BUFFER(tx_q, tx_q->tpd.produce_idx);
+ tpbuf->length = frag->size;
+ tpbuf->dma_addr = dma_map_page(adpt->netdev->dev.parent,
+ frag->page.p, frag->page_offset,
+ tpbuf->length, DMA_TO_DEVICE);
+ TPD_BUFFER_ADDR_L_SET(tpd, EMAC_DMA_ADDR_LO(tpbuf->dma_addr));
+ TPD_BUFFER_ADDR_H_SET(tpd, EMAC_DMA_ADDR_HI(tpbuf->dma_addr));
+ TPD_BUF_LEN_SET(tpd, tpbuf->length);
+ emac_tx_tpd_create(adpt, tx_q, tpd);
+ }
+
+ /* The last tpd */
+ emac_tx_tpd_mark_last(adpt, tx_q);
+
+ if (test_bit(EMAC_STATUS_TS_TX_EN, &adpt->status) &&
+ (skb_shinfo(skb)->tx_flags & SKBTX_HW_TSTAMP)) {
+ struct sk_buff *skb_ts = skb_clone(skb, GFP_ATOMIC);
+
+ if (likely(skb_ts)) {
+ unsigned long flags;
+
+ emac_tx_tpd_ts_save(adpt, tx_q);
+ skb_ts->sk = skb->sk;
+ EMAC_SKB_CB(skb_ts)->tpd_idx =
+ tx_q->tpd.last_produce_idx;
+ EMAC_SKB_CB(skb_ts)->jiffies = get_jiffies_64();
+ skb_shinfo(skb_ts)->tx_flags |= SKBTX_IN_PROGRESS;
+ spin_lock_irqsave(&adpt->tx_ts_lock, flags);
+ if (adpt->tx_ts_pending_queue.qlen >=
+ EMAC_TX_POLL_HWTXTSTAMP_THRESHOLD) {
+ emac_tx_ts_poll(adpt);
+ adpt->tx_ts_stats.tx_poll++;
+ }
+ __skb_queue_tail(&adpt->tx_ts_pending_queue,
+ skb_ts);
+ spin_unlock_irqrestore(&adpt->tx_ts_lock, flags);
+ adpt->tx_ts_stats.tx++;
+ emac_schedule_tx_ts_task(adpt);
+ }
+ }
+
+ /* The last buffer info contain the skb address,
+ * so it will be freed after unmap
+ */
+ tpbuf->skb = skb;
+}
+
+/* Transmit the packet using specified transmit queue */
+int emac_mac_tx_buf_send(struct emac_adapter *adpt, struct emac_tx_queue *tx_q,
+ struct sk_buff *skb)
+{
+ struct emac_tpd tpd;
+ u32 prod_idx;
+
+ if (test_bit(EMAC_STATUS_DOWN, &adpt->status)) {
+ dev_kfree_skb_any(skb);
+ return NETDEV_TX_OK;
+ }
+
+ if (!emac_tx_has_enough_descs(tx_q, skb)) {
+ /* not enough descriptors, just stop queue */
+ netif_stop_queue(adpt->netdev);
+ return NETDEV_TX_BUSY;
+ }
+
+ memset(&tpd, 0, sizeof(tpd));
+
+ if (emac_tso_csum(adpt, tx_q, skb, &tpd) != 0) {
+ dev_kfree_skb_any(skb);
+ return NETDEV_TX_OK;
+ }
+
+ if (skb_vlan_tag_present(skb)) {
+ u16 tag;
+
+ EMAC_VLAN_TO_TAG(skb_vlan_tag_get(skb), tag);
+ TPD_CVLAN_TAG_SET(&tpd, tag);
+ TPD_INSTC_SET(&tpd, 1);
+ }
+
+ if (skb_network_offset(skb) != ETH_HLEN)
+ TPD_TYP_SET(&tpd, 1);
+
+ emac_tx_fill_tpd(adpt, tx_q, skb, &tpd);
+
+ netdev_sent_queue(adpt->netdev, skb->len);
+
+ /* update produce idx */
+ prod_idx = (tx_q->tpd.produce_idx << tx_q->produce_shift) &
+ tx_q->produce_mask;
+ emac_reg_update32(adpt->base + tx_q->produce_reg,
+ tx_q->produce_mask, prod_idx);
+
+ return NETDEV_TX_OK;
+}
diff --git a/drivers/net/ethernet/qualcomm/emac/emac-mac.h b/drivers/net/ethernet/qualcomm/emac/emac-mac.h
new file mode 100644
index 0000000..23dcdb8
--- /dev/null
+++ b/drivers/net/ethernet/qualcomm/emac/emac-mac.h
@@ -0,0 +1,286 @@
+/* Copyright (c) 2013-2015, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+/* EMAC DMA HW engine uses three rings:
+ * Tx:
+ * TPD: Transmit Packet Descriptor ring.
+ * Rx:
+ * RFD: Receive Free Descriptor ring.
+ * Ring of descriptors with empty buffers to be filled by Rx HW.
+ * RRD: Receive Return Descriptor ring.
+ * Ring of descriptors with buffers filled with received data.
+ */
+
+#ifndef _EMAC_HW_H_
+#define _EMAC_HW_H_
+
+/* EMAC_CSR register offsets */
+#define EMAC_EMAC_WRAPPER_CSR1 0x000000
+#define EMAC_EMAC_WRAPPER_CSR2 0x000004
+#define EMAC_EMAC_WRAPPER_TX_TS_LO 0x000104
+#define EMAC_EMAC_WRAPPER_TX_TS_HI 0x000108
+#define EMAC_EMAC_WRAPPER_TX_TS_INX 0x00010c
+
+#define EMAC_MAC_IRQ_RES "core0_irq"
+
+/* DMA Order Settings */
+enum emac_dma_order {
+ emac_dma_ord_in = 1,
+ emac_dma_ord_enh = 2,
+ emac_dma_ord_out = 4
+};
+
+enum emac_mac_speed {
+ emac_mac_speed_0 = 0,
+ emac_mac_speed_10_100 = 1,
+ emac_mac_speed_1000 = 2
+};
+
+enum emac_dma_req_block {
+ emac_dma_req_128 = 0,
+ emac_dma_req_256 = 1,
+ emac_dma_req_512 = 2,
+ emac_dma_req_1024 = 3,
+ emac_dma_req_2048 = 4,
+ emac_dma_req_4096 = 5
+};
+
+/* Returns the value of bits idx...idx+n_bits */
+#define BITS_MASK(idx, n_bits) (((((unsigned long)1) << (n_bits)) - 1) << (idx))
+#define BITS_GET(val, idx, n_bits) (((val) & BITS_MASK(idx, n_bits)) >> idx)
+#define BITS_SET(val, idx, n_bits, new_val) \
+ ((val) = (((val) & (~BITS_MASK(idx, n_bits))) | \
+ (((new_val) << (idx)) & BITS_MASK(idx, n_bits))))
+
+/* RRD (Receive Return Descriptor) */
+struct emac_rrd {
+ u32 word[6];
+
+/* number of RFD */
+#define RRD_NOR(rrd) BITS_GET((rrd)->word[0], 16, 4)
+/* start consumer index of rfd-ring */
+#define RRD_SI(rrd) BITS_GET((rrd)->word[0], 20, 12)
+/* vlan-tag (CVID, CFI and PRI) */
+#define RRD_CVALN_TAG(rrd) BITS_GET((rrd)->word[2], 0, 16)
+/* length of the packet */
+#define RRD_PKT_SIZE(rrd) BITS_GET((rrd)->word[3], 0, 14)
+/* L4(TCP/UDP) checksum failed */
+#define RRD_L4F(rrd) BITS_GET((rrd)->word[3], 14, 1)
+/* vlan tagged */
+#define RRD_CVTAG(rrd) BITS_GET((rrd)->word[3], 16, 1)
+/* When set, indicates that the descriptor is updated by the IP core.
+ * When cleared, indicates that the descriptor is invalid.
+ */
+#define RRD_UPDT(rrd) BITS_GET((rrd)->word[3], 31, 1)
+#define RRD_UPDT_SET(rrd, val) BITS_SET((rrd)->word[3], 31, 1, val)
+/* timestamp low */
+#define RRD_TS_LOW(rrd) BITS_GET((rrd)->word[4], 0, 30)
+/* timestamp high */
+#define RRD_TS_HI(rrd) ((rrd)->word[5])
+};
+
+/* RFD (Receive Free Descriptor) */
+union emac_rfd {
+ u64 addr;
+ u32 word[2];
+};
+
+/* TPD (Transmit Packet Descriptor) */
+struct emac_tpd {
+ u32 word[4];
+
+/* Number of bytes of the transmit packet. (include 4-byte CRC) */
+#define TPD_BUF_LEN_SET(tpd, val) BITS_SET((tpd)->word[0], 0, 16, val)
+/* Custom Checksum Offload: When set, ask IP core to offload custom checksum */
+#define TPD_CSX_SET(tpd, val) BITS_SET((tpd)->word[1], 8, 1, val)
+/* TCP Large Send Offload: When set, ask IP core to do offload TCP Large Send */
+#define TPD_LSO(tpd) BITS_GET((tpd)->word[1], 12, 1)
+#define TPD_LSO_SET(tpd, val) BITS_SET((tpd)->word[1], 12, 1, val)
+/* Large Send Offload Version: When set, indicates this is an LSOv2
+ * (for both IPv4 and IPv6). When cleared, indicates this is an LSOv1
+ * (only for IPv4).
+ */
+#define TPD_LSOV_SET(tpd, val) BITS_SET((tpd)->word[1], 13, 1, val)
+/* IPv4 packet: When set, indicates this is an IPv4 packet, this bit is only
+ * for LSOV2 format.
+ */
+#define TPD_IPV4_SET(tpd, val) BITS_SET((tpd)->word[1], 16, 1, val)
+/* 0: Ethernet frame (DA+SA+TYPE+DATA+CRC)
+ * 1: IEEE 802.3 frame (DA+SA+LEN+DSAP+SSAP+CTL+ORG+TYPE+DATA+CRC)
+ */
+#define TPD_TYP_SET(tpd, val) BITS_SET((tpd)->word[1], 17, 1, val)
+/* Low-32bit Buffer Address */
+#define TPD_BUFFER_ADDR_L_SET(tpd, val) ((tpd)->word[2] = (val))
+/* CVLAN Tag to be inserted if INS_VLAN_TAG is set, CVLAN TPID based on global
+ * register configuration.
+ */
+#define TPD_CVLAN_TAG_SET(tpd, val) BITS_SET((tpd)->word[3], 0, 16, val)
+/* Insert CVlan Tag: When set, ask MAC to insert CVLAN TAG to outgoing packet
+ */
+#define TPD_INSTC_SET(tpd, val) BITS_SET((tpd)->word[3], 17, 1, val)
+/* High-14bit Buffer Address, So, the 64b-bit address is
+ * {DESC_CTRL_11_TX_DATA_HIADDR[17:0],(register) BUFFER_ADDR_H, BUFFER_ADDR_L}
+ */
+#define TPD_BUFFER_ADDR_H_SET(tpd, val) BITS_SET((tpd)->word[3], 18, 13, val)
+/* Format D. Word offset from the 1st byte of this packet to start to calculate
+ * the custom checksum.
+ */
+#define TPD_PAYLOAD_OFFSET_SET(tpd, val) BITS_SET((tpd)->word[1], 0, 8, val)
+/* Format D. Word offset from the 1st byte of this packet to fill the custom
+ * checksum to
+ */
+#define TPD_CXSUM_OFFSET_SET(tpd, val) BITS_SET((tpd)->word[1], 18, 8, val)
+
+/* Format C. TCP Header offset from the 1st byte of this packet. (byte unit) */
+#define TPD_TCPHDR_OFFSET_SET(tpd, val) BITS_SET((tpd)->word[1], 0, 8, val)
+/* Format C. MSS (Maximum Segment Size) got from the protocol layer. (byte unit)
+ */
+#define TPD_MSS_SET(tpd, val) BITS_SET((tpd)->word[1], 18, 13, val)
+/* packet length in ext tpd */
+#define TPD_PKT_LEN_SET(tpd, val) ((tpd)->word[2] = (val))
+};
+
+/* emac_ring_header represents a single, contiguous block of DMA space
+ * mapped for the three descriptor rings (tpd, rfd, rrd)
+ */
+struct emac_ring_header {
+ void *v_addr; /* virtual address */
+ dma_addr_t dma_addr; /* dma address */
+ size_t size; /* length in bytes */
+ size_t used;
+};
+
+/* emac_buffer is wrapper around a pointer to a socket buffer
+ * so a DMA handle can be stored along with the skb
+ */
+struct emac_buffer {
+ struct sk_buff *skb; /* socket buffer */
+ u16 length; /* rx buffer length */
+ dma_addr_t dma_addr; /* dma address */
+};
+
+/* receive free descriptor (rfd) ring */
+struct emac_rfd_ring {
+ struct emac_buffer *rfbuff;
+ u32 __iomem *v_addr; /* virtual address */
+ dma_addr_t dma_addr; /* dma address */
+ u64 size; /* length in bytes */
+ u32 count; /* number of desc in the ring */
+ u32 produce_idx;
+ u32 process_idx;
+ u32 consume_idx; /* unused */
+};
+
+/* Receive Return Desciptor (RRD) ring */
+struct emac_rrd_ring {
+ u32 __iomem *v_addr; /* virtual address */
+ dma_addr_t dma_addr; /* physical address */
+ u64 size; /* length in bytes */
+ u32 count; /* number of desc in the ring */
+ u32 produce_idx; /* unused */
+ u32 consume_idx;
+};
+
+/* Rx queue */
+struct emac_rx_queue {
+ struct net_device *netdev; /* netdev ring belongs to */
+ struct emac_rrd_ring rrd;
+ struct emac_rfd_ring rfd;
+ struct napi_struct napi;
+ struct emac_irq *irq;
+
+ u32 intr;
+ u32 produce_mask;
+ u32 process_mask;
+ u32 consume_mask;
+
+ u16 produce_reg;
+ u16 process_reg;
+ u16 consume_reg;
+
+ u8 produce_shift;
+ u8 process_shft;
+ u8 consume_shift;
+};
+
+/* Transimit Packet Descriptor (tpd) ring */
+struct emac_tpd_ring {
+ struct emac_buffer *tpbuff;
+ u32 __iomem *v_addr; /* virtual address */
+ dma_addr_t dma_addr; /* dma address */
+
+ u64 size; /* length in bytes */
+ u32 count; /* number of desc in the ring */
+ u32 produce_idx;
+ u32 consume_idx;
+ u32 last_produce_idx;
+};
+
+/* Tx queue */
+struct emac_tx_queue {
+ struct emac_tpd_ring tpd;
+
+ u32 produce_mask;
+ u32 consume_mask;
+
+ u16 max_packets; /* max packets per interrupt */
+ u16 produce_reg;
+ u16 consume_reg;
+
+ u8 produce_shift;
+ u8 consume_shift;
+};
+
+/* HW tx timestamp */
+struct emac_tx_ts {
+ u32 ts_idx;
+ u32 sec;
+ u32 ns;
+};
+
+/* Tx timestamp statistics */
+struct emac_tx_ts_stats {
+ u32 tx;
+ u32 rx;
+ u32 deliver;
+ u32 drop;
+ u32 lost;
+ u32 timeout;
+ u32 sched;
+ u32 poll;
+ u32 tx_poll;
+};
+
+struct emac_adapter;
+
+int emac_mac_up(struct emac_adapter *adpt);
+void emac_mac_down(struct emac_adapter *adpt, bool reset);
+void emac_mac_reset(struct emac_adapter *adpt);
+void emac_mac_start(struct emac_adapter *adpt);
+void emac_mac_stop(struct emac_adapter *adpt);
+void emac_mac_addr_clear(struct emac_adapter *adpt, u8 *addr);
+void emac_mac_pm(struct emac_adapter *adpt);
+void emac_mac_mode_config(struct emac_adapter *adpt);
+void emac_mac_rx_process(struct emac_adapter *adpt, struct emac_rx_queue *rx_q,
+ int *num_pkts, int max_pkts);
+int emac_mac_tx_buf_send(struct emac_adapter *adpt, struct emac_tx_queue *tx_q,
+ struct sk_buff *skb);
+void emac_mac_tx_process(struct emac_adapter *adpt, struct emac_tx_queue *tx_q);
+void emac_mac_rx_tx_ring_init_all(struct platform_device *pdev,
+ struct emac_adapter *adpt);
+int emac_mac_rx_tx_rings_alloc_all(struct emac_adapter *adpt);
+void emac_mac_rx_tx_rings_free_all(struct emac_adapter *adpt);
+void emac_mac_tx_ts_periodic_routine(struct work_struct *work);
+void emac_mac_multicast_addr_clear(struct emac_adapter *adpt);
+void emac_mac_multicast_addr_set(struct emac_adapter *adpt, u8 *addr);
+
+#endif /*_EMAC_HW_H_*/
diff --git a/drivers/net/ethernet/qualcomm/emac/emac-phy.c b/drivers/net/ethernet/qualcomm/emac/emac-phy.c
new file mode 100644
index 0000000..ef51b537
--- /dev/null
+++ b/drivers/net/ethernet/qualcomm/emac/emac-phy.c
@@ -0,0 +1,486 @@
+/* Copyright (c) 2013-2015, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+/* Qualcomm Technologies, Inc. EMAC PHY Controller driver.
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_net.h>
+#include <linux/pm_runtime.h>
+#include <linux/phy.h>
+#include <linux/iopoll.h>
+#include "emac.h"
+#include "emac-mac.h"
+#include "emac-phy.h"
+#include "emac-sgmii.h"
+
+/* EMAC base register offsets */
+#define EMAC_MDIO_CTRL 0x001414
+#define EMAC_PHY_STS 0x001418
+#define EMAC_MDIO_EX_CTRL 0x001440
+
+/* EMAC_MDIO_CTRL */
+#define MDIO_MODE BIT(30)
+#define MDIO_PR BIT(29)
+#define MDIO_AP_EN BIT(28)
+#define MDIO_BUSY BIT(27)
+#define MDIO_CLK_SEL_BMSK 0x7000000
+#define MDIO_CLK_SEL_SHFT 24
+#define MDIO_START BIT(23)
+#define SUP_PREAMBLE BIT(22)
+#define MDIO_RD_NWR BIT(21)
+#define MDIO_REG_ADDR_BMSK 0x1f0000
+#define MDIO_REG_ADDR_SHFT 16
+#define MDIO_DATA_BMSK 0xffff
+#define MDIO_DATA_SHFT 0
+
+/* EMAC_PHY_STS */
+#define PHY_ADDR_BMSK 0x1f0000
+#define PHY_ADDR_SHFT 16
+
+/* EMAC_MDIO_EX_CTRL */
+#define DEVAD_BMSK 0x1f0000
+#define DEVAD_SHFT 16
+#define EX_REG_ADDR_BMSK 0xffff
+#define EX_REG_ADDR_SHFT 0
+
+#define MDIO_CLK_25_4 0
+#define MDIO_CLK_25_28 7
+
+#define MDIO_WAIT_TIMES 1000
+
+/* PHY */
+#define MII_PSSR 0x11 /* PHY Specific Status Reg */
+
+/* MII_BMCR (0x00) */
+#define BMCR_SPEED10 0x0000
+
+/* MII_PSSR (0x11) */
+#define PSSR_SPD_DPLX_RESOLVED 0x0800 /* 1=Speed & Duplex resolved */
+#define PSSR_DPLX 0x2000 /* 1=Duplex 0=Half Duplex */
+#define PSSR_SPEED 0xC000 /* Speed, bits 14:15 */
+#define PSSR_10MBS 0x0000 /* 00=10Mbs */
+#define PSSR_100MBS 0x4000 /* 01=100Mbs */
+#define PSSR_1000MBS 0x8000 /* 10=1000Mbs */
+
+#define EMAC_LINK_SPEED_DEFAULT (\
+ EMAC_LINK_SPEED_10_HALF |\
+ EMAC_LINK_SPEED_10_FULL |\
+ EMAC_LINK_SPEED_100_HALF |\
+ EMAC_LINK_SPEED_100_FULL |\
+ EMAC_LINK_SPEED_1GB_FULL)
+
+static int emac_phy_mdio_autopoll_disable(struct emac_adapter *adpt)
+{
+ u32 val;
+
+ /* disable autopoll */
+ emac_reg_update32(adpt->base + EMAC_MDIO_CTRL, MDIO_AP_EN, 0);
+
+ /* wait for any mdio polling to complete */
+ if (!readl_poll_timeout(adpt->base + EMAC_MDIO_CTRL, val,
+ !(val & MDIO_BUSY), 100, MDIO_WAIT_TIMES * 100))
+ return 0;
+
+ /* failed to disable; ensure it is enabled before returning */
+ emac_reg_update32(adpt->base + EMAC_MDIO_CTRL, 0, MDIO_AP_EN);
+
+ return -EBUSY;
+}
+
+static void emac_phy_mdio_autopoll_enable(struct emac_adapter *adpt)
+{
+ emac_reg_update32(adpt->base + EMAC_MDIO_CTRL, 0, MDIO_AP_EN);
+}
+
+int emac_phy_read_reg(struct emac_adapter *adpt, bool ext, u8 dev, bool fast,
+ u16 reg_addr, u16 *phy_data)
+{
+ struct emac_phy *phy = &adpt->phy;
+ u32 clk_sel, val = 0;
+ int ret = 0;
+
+ *phy_data = 0;
+ clk_sel = fast ? MDIO_CLK_25_4 : MDIO_CLK_25_28;
+
+ if (phy->external) {
+ ret = emac_phy_mdio_autopoll_disable(adpt);
+ if (ret)
+ return ret;
+ }
+ /* set PHY address */
+ emac_reg_update32(adpt->base + EMAC_PHY_STS, PHY_ADDR_BMSK,
+ (dev << PHY_ADDR_SHFT));
+
+ if (ext) {
+ val = ((dev << DEVAD_SHFT) & DEVAD_BMSK) |
+ ((reg_addr << EX_REG_ADDR_SHFT) & EX_REG_ADDR_BMSK);
+ writel(val, adpt->base + EMAC_MDIO_EX_CTRL);
+
+ val = SUP_PREAMBLE |
+ ((clk_sel << MDIO_CLK_SEL_SHFT) & MDIO_CLK_SEL_BMSK) |
+ MDIO_START | MDIO_MODE | MDIO_RD_NWR;
+ } else {
+ val = val & ~(MDIO_REG_ADDR_BMSK | MDIO_CLK_SEL_BMSK |
+ MDIO_MODE | MDIO_PR);
+ val = SUP_PREAMBLE |
+ ((clk_sel << MDIO_CLK_SEL_SHFT) & MDIO_CLK_SEL_BMSK) |
+ ((reg_addr << MDIO_REG_ADDR_SHFT) & MDIO_REG_ADDR_BMSK) |
+ MDIO_START | MDIO_RD_NWR;
+ }
+
+ writel(val, adpt->base + EMAC_MDIO_CTRL);
+
+ if (readl_poll_timeout(adpt->base + EMAC_MDIO_CTRL, val,
+ !(val & (MDIO_START | MDIO_BUSY)),
+ 100, MDIO_WAIT_TIMES * 100))
+ ret = -EIO;
+ else
+ *phy_data = ((val >> MDIO_DATA_SHFT) & MDIO_DATA_BMSK);
+
+ if (phy->external)
+ emac_phy_mdio_autopoll_enable(adpt);
+
+ return ret;
+}
+
+int emac_phy_write_reg(struct emac_adapter *adpt, bool ext, u8 dev, bool fast,
+ u16 reg_addr, u16 phy_data)
+{
+ struct emac_phy *phy = &adpt->phy;
+ u32 clk_sel, val = 0;
+ int ret = 0;
+
+ clk_sel = fast ? MDIO_CLK_25_4 : MDIO_CLK_25_28;
+
+ if (phy->external) {
+ ret = emac_phy_mdio_autopoll_disable(adpt);
+ if (ret)
+ return ret;
+ }
+
+ /* set PHY address */
+ emac_reg_update32(adpt->base + EMAC_PHY_STS, PHY_ADDR_BMSK,
+ (dev << PHY_ADDR_SHFT));
+
+ if (ext) {
+ val = ((dev << DEVAD_SHFT) & DEVAD_BMSK) |
+ ((reg_addr << EX_REG_ADDR_SHFT) & EX_REG_ADDR_BMSK);
+ writel(val, adpt->base + EMAC_MDIO_EX_CTRL);
+
+ val = SUP_PREAMBLE |
+ ((clk_sel << MDIO_CLK_SEL_SHFT) & MDIO_CLK_SEL_BMSK) |
+ ((phy_data << MDIO_DATA_SHFT) & MDIO_DATA_BMSK) |
+ MDIO_START | MDIO_MODE;
+ } else {
+ val = val & ~(MDIO_REG_ADDR_BMSK | MDIO_CLK_SEL_BMSK |
+ MDIO_DATA_BMSK | MDIO_MODE | MDIO_PR);
+ val = SUP_PREAMBLE |
+ ((clk_sel << MDIO_CLK_SEL_SHFT) & MDIO_CLK_SEL_BMSK) |
+ ((reg_addr << MDIO_REG_ADDR_SHFT) & MDIO_REG_ADDR_BMSK) |
+ ((phy_data << MDIO_DATA_SHFT) & MDIO_DATA_BMSK) |
+ MDIO_START;
+ }
+
+ writel(val, adpt->base + EMAC_MDIO_CTRL);
+
+ if (readl_poll_timeout(adpt->base + EMAC_MDIO_CTRL, val,
+ !(val & (MDIO_START | MDIO_BUSY)), 100,
+ MDIO_WAIT_TIMES * 100))
+ ret = -EIO;
+
+ if (phy->external)
+ emac_phy_mdio_autopoll_enable(adpt);
+
+ return ret;
+}
+
+int emac_phy_read(struct emac_adapter *adpt, u16 phy_addr, u16 reg_addr,
+ u16 *phy_data)
+{
+ struct emac_phy *phy = &adpt->phy;
+ int ret;
+
+ mutex_lock(&phy->lock);
+ ret = emac_phy_read_reg(adpt, false, phy_addr, true, reg_addr,
+ phy_data);
+ mutex_unlock(&phy->lock);
+
+ if (ret)
+ netdev_err(adpt->netdev, "error: reading phy reg 0x%02x\n",
+ reg_addr);
+ else
+ netif_dbg(adpt, hw, adpt->netdev,
+ "EMAC PHY RD: 0x%02x -> 0x%04x\n", reg_addr,
+ *phy_data);
+
+ return ret;
+}
+
+int emac_phy_write(struct emac_adapter *adpt, u16 phy_addr, u16 reg_addr,
+ u16 phy_data)
+{
+ struct emac_phy *phy = &adpt->phy;
+ int ret;
+
+ mutex_lock(&phy->lock);
+ ret = emac_phy_write_reg(adpt, false, phy_addr, true, reg_addr,
+ phy_data);
+ mutex_unlock(&phy->lock);
+
+ if (ret)
+ netdev_err(adpt->netdev, "error: writing phy reg 0x%02x\n",
+ reg_addr);
+ else
+ netif_dbg(adpt, hw,
+ adpt->netdev, "EMAC PHY WR: 0x%02x <- 0x%04x\n",
+ reg_addr, phy_data);
+
+ return ret;
+}
+
+/* initialize external phy */
+int emac_phy_external_init(struct emac_adapter *adpt)
+{
+ struct emac_phy *phy = &adpt->phy;
+ u16 phy_id[2];
+ int ret = 0;
+
+ if (phy->external) {
+ ret = emac_phy_read(adpt, phy->addr, MII_PHYSID1, &phy_id[0]);
+ if (ret)
+ return ret;
+
+ ret = emac_phy_read(adpt, phy->addr, MII_PHYSID2, &phy_id[1]);
+ if (ret)
+ return ret;
+
+ phy->id[0] = phy_id[0];
+ phy->id[1] = phy_id[1];
+ } else {
+ emac_phy_mdio_autopoll_disable(adpt);
+ }
+
+ return 0;
+}
+
+static int emac_phy_link_setup_external(struct emac_adapter *adpt,
+ enum emac_flow_ctrl req_fc_mode,
+ u32 speed, bool autoneg, bool fc)
+{
+ struct emac_phy *phy = &adpt->phy;
+ u16 adv, bmcr, ctrl1000 = 0;
+ int ret = 0;
+
+ if (autoneg) {
+ switch (req_fc_mode) {
+ case EMAC_FC_FULL:
+ case EMAC_FC_RX_PAUSE:
+ adv = ADVERTISE_PAUSE_CAP | ADVERTISE_PAUSE_ASYM;
+ break;
+ case EMAC_FC_TX_PAUSE:
+ adv = ADVERTISE_PAUSE_ASYM;
+ break;
+ default:
+ adv = 0;
+ break;
+ }
+ if (!fc)
+ adv &= ~(ADVERTISE_PAUSE_CAP | ADVERTISE_PAUSE_ASYM);
+
+ if (speed & EMAC_LINK_SPEED_10_HALF)
+ adv |= ADVERTISE_10HALF;
+
+ if (speed & EMAC_LINK_SPEED_10_FULL)
+ adv |= ADVERTISE_10HALF | ADVERTISE_10FULL;
+
+ if (speed & EMAC_LINK_SPEED_100_HALF)
+ adv |= ADVERTISE_100HALF;
+
+ if (speed & EMAC_LINK_SPEED_100_FULL)
+ adv |= ADVERTISE_100HALF | ADVERTISE_100FULL;
+
+ if (speed & EMAC_LINK_SPEED_1GB_FULL)
+ ctrl1000 |= ADVERTISE_1000FULL;
+
+ ret |= emac_phy_write(adpt, phy->addr, MII_ADVERTISE, adv);
+ ret |= emac_phy_write(adpt, phy->addr, MII_CTRL1000, ctrl1000);
+
+ bmcr = BMCR_RESET | BMCR_ANENABLE | BMCR_ANRESTART;
+ ret |= emac_phy_write(adpt, phy->addr, MII_BMCR, bmcr);
+ } else {
+ bmcr = BMCR_RESET;
+ switch (speed) {
+ case EMAC_LINK_SPEED_10_HALF:
+ bmcr |= BMCR_SPEED10;
+ break;
+ case EMAC_LINK_SPEED_10_FULL:
+ bmcr |= BMCR_SPEED10 | BMCR_FULLDPLX;
+ break;
+ case EMAC_LINK_SPEED_100_HALF:
+ bmcr |= BMCR_SPEED100;
+ break;
+ case EMAC_LINK_SPEED_100_FULL:
+ bmcr |= BMCR_SPEED100 | BMCR_FULLDPLX;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ ret |= emac_phy_write(adpt, phy->addr, MII_BMCR, bmcr);
+ }
+
+ return ret;
+}
+
+int emac_phy_link_setup(struct emac_adapter *adpt, u32 speed, bool autoneg,
+ bool fc)
+{
+ struct emac_phy *phy = &adpt->phy;
+ int ret = 0;
+
+ if (!phy->external)
+ return emac_sgmii_no_ephy_link_setup(adpt, speed, autoneg);
+
+ if (emac_phy_link_setup_external(adpt, phy->req_fc_mode, speed, autoneg,
+ fc)) {
+ netdev_err(adpt->netdev,
+ "error: on ephy setup speed:%d autoneg:%d fc:%d\n",
+ speed, autoneg, fc);
+ ret = -EINVAL;
+ } else {
+ phy->autoneg = autoneg;
+ }
+
+ return ret;
+}
+
+int emac_phy_link_check(struct emac_adapter *adpt, u32 *speed, bool *link_up)
+{
+ struct emac_phy *phy = &adpt->phy;
+ u16 bmsr, pssr;
+ int ret;
+
+ if (!phy->external) {
+ emac_sgmii_no_ephy_link_check(adpt, speed, link_up);
+ return 0;
+ }
+
+ ret = emac_phy_read(adpt, phy->addr, MII_BMSR, &bmsr);
+ if (ret)
+ return ret;
+
+ if (!(bmsr & BMSR_LSTATUS)) {
+ *link_up = false;
+ *speed = EMAC_LINK_SPEED_UNKNOWN;
+ return 0;
+ }
+ *link_up = true;
+ ret = emac_phy_read(adpt, phy->addr, MII_PSSR, &pssr);
+ if (ret)
+ return ret;
+
+ if (!(pssr & PSSR_SPD_DPLX_RESOLVED)) {
+ netdev_err(adpt->netdev, "error: speed duplex resolved\n");
+ return -EINVAL;
+ }
+
+ switch (pssr & PSSR_SPEED) {
+ case PSSR_1000MBS:
+ if (pssr & PSSR_DPLX)
+ *speed = EMAC_LINK_SPEED_1GB_FULL;
+ else
+ netdev_err(adpt->netdev,
+ "error: 1000M half duplex is invalid");
+ break;
+ case PSSR_100MBS:
+ if (pssr & PSSR_DPLX)
+ *speed = EMAC_LINK_SPEED_100_FULL;
+ else
+ *speed = EMAC_LINK_SPEED_100_HALF;
+ break;
+ case PSSR_10MBS:
+ if (pssr & PSSR_DPLX)
+ *speed = EMAC_LINK_SPEED_10_FULL;
+ else
+ *speed = EMAC_LINK_SPEED_10_HALF;
+ break;
+ default:
+ *speed = EMAC_LINK_SPEED_UNKNOWN;
+ ret = -EINVAL;
+ break;
+ }
+
+ return ret;
+}
+
+/* Read speed off the LPA (Link Partner Ability) register */
+void emac_phy_link_speed_get(struct emac_adapter *adpt, u32 *speed)
+{
+ struct emac_phy *phy = &adpt->phy;
+ int ret;
+ u16 lpa, stat1000;
+ bool link;
+
+ if (!phy->external) {
+ emac_sgmii_no_ephy_link_check(adpt, speed, &link);
+ return;
+ }
+
+ ret = emac_phy_read(adpt, phy->addr, MII_LPA, &lpa);
+ ret |= emac_phy_read(adpt, phy->addr, MII_STAT1000, &stat1000);
+ if (ret)
+ return;
+
+ *speed = EMAC_LINK_SPEED_10_HALF;
+ if (lpa & LPA_10FULL)
+ *speed = EMAC_LINK_SPEED_10_FULL;
+ else if (lpa & LPA_10HALF)
+ *speed = EMAC_LINK_SPEED_10_HALF;
+ else if (lpa & LPA_100FULL)
+ *speed = EMAC_LINK_SPEED_100_FULL;
+ else if (lpa & LPA_100HALF)
+ *speed = EMAC_LINK_SPEED_100_HALF;
+ else if (stat1000 & LPA_1000FULL)
+ *speed = EMAC_LINK_SPEED_1GB_FULL;
+}
+
+/* Read phy configuration and initialize it */
+int emac_phy_config(struct platform_device *pdev, struct emac_adapter *adpt)
+{
+ struct emac_phy *phy = &adpt->phy;
+ struct device_node *dt = pdev->dev.of_node;
+ int ret;
+
+ phy->external = !of_property_read_bool(dt, "qcom,no-external-phy");
+
+ /* get phy address on MDIO bus */
+ if (phy->external) {
+ ret = of_property_read_u32(dt, "phy-addr", &phy->addr);
+ if (ret)
+ return ret;
+ } else {
+ phy->uses_gpios = false;
+ }
+
+ ret = emac_sgmii_config(pdev, adpt);
+ if (ret)
+ return ret;
+
+ mutex_init(&phy->lock);
+
+ phy->autoneg = true;
+ phy->autoneg_advertised = EMAC_LINK_SPEED_DEFAULT;
+
+ return emac_sgmii_init(adpt);
+}
diff --git a/drivers/net/ethernet/qualcomm/emac/emac-phy.h b/drivers/net/ethernet/qualcomm/emac/emac-phy.h
new file mode 100644
index 0000000..c40e1db
--- /dev/null
+++ b/drivers/net/ethernet/qualcomm/emac/emac-phy.h
@@ -0,0 +1,69 @@
+/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
+*
+* This program is free software; you can redistribute it and/or modify
+* it under the terms of the GNU General Public License version 2 and
+* only version 2 as published by the Free Software Foundation.
+*
+* This program is distributed in the hope that it will be useful,
+* but WITHOUT ANY WARRANTY; without even the implied warranty of
+* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+* GNU General Public License for more details.
+*/
+
+#ifndef _EMAC_PHY_H_
+#define _EMAC_PHY_H_
+
+enum emac_flow_ctrl {
+ EMAC_FC_NONE,
+ EMAC_FC_RX_PAUSE,
+ EMAC_FC_TX_PAUSE,
+ EMAC_FC_FULL,
+ EMAC_FC_DEFAULT
+};
+
+/* emac_phy
+ * @base register file base address space.
+ * @irq phy interrupt number.
+ * @external true when external phy is used.
+ * @addr mii address.
+ * @id vendor id.
+ * @cur_fc_mode flow control mode in effect.
+ * @req_fc_mode flow control mode requested by caller.
+ * @disable_fc_autoneg Do not auto-negotiate flow control.
+ */
+struct emac_phy {
+ void __iomem *base;
+ int irq;
+
+ bool external;
+ bool uses_gpios;
+ u32 addr;
+ u16 id[2];
+ bool autoneg;
+ u32 autoneg_advertised;
+ u32 link_speed;
+ bool link_up;
+ /* lock - synchronize access to mdio bus */
+ struct mutex lock;
+
+ /* flow control configuration */
+ enum emac_flow_ctrl cur_fc_mode;
+ enum emac_flow_ctrl req_fc_mode;
+ bool disable_fc_autoneg;
+};
+
+struct emac_adapter;
+struct platform_device;
+
+int emac_phy_read(struct emac_adapter *adpt, u16 phy_addr, u16 reg_addr,
+ u16 *phy_data);
+int emac_phy_write(struct emac_adapter *adpt, u16 phy_addr, u16 reg_addr,
+ u16 phy_data);
+int emac_phy_config(struct platform_device *pdev, struct emac_adapter *adpt);
+int emac_phy_external_init(struct emac_adapter *adpt);
+int emac_phy_link_setup(struct emac_adapter *adpt, u32 speed, bool autoneg,
+ bool fc);
+int emac_phy_link_check(struct emac_adapter *adpt, u32 *speed, bool *link_up);
+void emac_phy_link_speed_get(struct emac_adapter *adpt, u32 *speed);
+
+#endif /* _EMAC_PHY_H_ */
diff --git a/drivers/net/ethernet/qualcomm/emac/emac-sgmii.c b/drivers/net/ethernet/qualcomm/emac/emac-sgmii.c
new file mode 100644
index 0000000..2f6a2ff
--- /dev/null
+++ b/drivers/net/ethernet/qualcomm/emac/emac-sgmii.c
@@ -0,0 +1,679 @@
+/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+/* Qualcomm Technologies, Inc. EMAC SGMII Controller driver.
+ */
+
+#include <linux/iopoll.h>
+#include "emac.h"
+#include "emac-mac.h"
+#include "emac-sgmii.h"
+
+/* EMAC_QSERDES register offsets */
+#define EMAC_QSERDES_COM_SYS_CLK_CTRL 0x000000
+#define EMAC_QSERDES_COM_PLL_CNTRL 0x000014
+#define EMAC_QSERDES_COM_PLL_IP_SETI 0x000018
+#define EMAC_QSERDES_COM_PLL_CP_SETI 0x000024
+#define EMAC_QSERDES_COM_PLL_IP_SETP 0x000028
+#define EMAC_QSERDES_COM_PLL_CP_SETP 0x00002c
+#define EMAC_QSERDES_COM_SYSCLK_EN_SEL 0x000038
+#define EMAC_QSERDES_COM_RESETSM_CNTRL 0x000040
+#define EMAC_QSERDES_COM_PLLLOCK_CMP1 0x000044
+#define EMAC_QSERDES_COM_PLLLOCK_CMP2 0x000048
+#define EMAC_QSERDES_COM_PLLLOCK_CMP3 0x00004c
+#define EMAC_QSERDES_COM_PLLLOCK_CMP_EN 0x000050
+#define EMAC_QSERDES_COM_DEC_START1 0x000064
+#define EMAC_QSERDES_COM_DIV_FRAC_START1 0x000098
+#define EMAC_QSERDES_COM_DIV_FRAC_START2 0x00009c
+#define EMAC_QSERDES_COM_DIV_FRAC_START3 0x0000a0
+#define EMAC_QSERDES_COM_DEC_START2 0x0000a4
+#define EMAC_QSERDES_COM_PLL_CRCTRL 0x0000ac
+#define EMAC_QSERDES_COM_RESET_SM 0x0000bc
+#define EMAC_QSERDES_TX_BIST_MODE_LANENO 0x000100
+#define EMAC_QSERDES_TX_TX_EMP_POST1_LVL 0x000108
+#define EMAC_QSERDES_TX_TX_DRV_LVL 0x00010c
+#define EMAC_QSERDES_TX_LANE_MODE 0x000150
+#define EMAC_QSERDES_TX_TRAN_DRVR_EMP_EN 0x000170
+#define EMAC_QSERDES_RX_CDR_CONTROL 0x000200
+#define EMAC_QSERDES_RX_CDR_CONTROL2 0x000210
+#define EMAC_QSERDES_RX_RX_EQ_GAIN12 0x000230
+
+/* EMAC_SGMII register offsets */
+#define EMAC_SGMII_PHY_SERDES_START 0x000300
+#define EMAC_SGMII_PHY_CMN_PWR_CTRL 0x000304
+#define EMAC_SGMII_PHY_RX_PWR_CTRL 0x000308
+#define EMAC_SGMII_PHY_TX_PWR_CTRL 0x00030C
+#define EMAC_SGMII_PHY_LANE_CTRL1 0x000318
+#define EMAC_SGMII_PHY_AUTONEG_CFG2 0x000348
+#define EMAC_SGMII_PHY_CDR_CTRL0 0x000358
+#define EMAC_SGMII_PHY_SPEED_CFG1 0x000374
+#define EMAC_SGMII_PHY_POW_DWN_CTRL0 0x000380
+#define EMAC_SGMII_PHY_RESET_CTRL 0x0003a8
+#define EMAC_SGMII_PHY_IRQ_CMD 0x0003ac
+#define EMAC_SGMII_PHY_INTERRUPT_CLEAR 0x0003b0
+#define EMAC_SGMII_PHY_INTERRUPT_MASK 0x0003b4
+#define EMAC_SGMII_PHY_INTERRUPT_STATUS 0x0003b8
+#define EMAC_SGMII_PHY_RX_CHK_STATUS 0x0003d4
+#define EMAC_SGMII_PHY_AUTONEG0_STATUS 0x0003e0
+#define EMAC_SGMII_PHY_AUTONEG1_STATUS 0x0003e4
+
+#define SGMII_CDR_MAX_CNT 0x0f
+
+#define QSERDES_PLL_IPSETI 0x01
+#define QSERDES_PLL_CP_SETI 0x3b
+#define QSERDES_PLL_IP_SETP 0x0a
+#define QSERDES_PLL_CP_SETP 0x09
+#define QSERDES_PLL_CRCTRL 0xfb
+#define QSERDES_PLL_DEC 0x02
+#define QSERDES_PLL_DIV_FRAC_START1 0x55
+#define QSERDES_PLL_DIV_FRAC_START2 0x2a
+#define QSERDES_PLL_DIV_FRAC_START3 0x03
+#define QSERDES_PLL_LOCK_CMP1 0x2b
+#define QSERDES_PLL_LOCK_CMP2 0x68
+#define QSERDES_PLL_LOCK_CMP3 0x00
+
+#define QSERDES_RX_CDR_CTRL1_THRESH 0x03
+#define QSERDES_RX_CDR_CTRL1_GAIN 0x02
+#define QSERDES_RX_CDR_CTRL2_THRESH 0x03
+#define QSERDES_RX_CDR_CTRL2_GAIN 0x04
+#define QSERDES_RX_EQ_GAIN2 0x0f
+#define QSERDES_RX_EQ_GAIN1 0x0f
+
+#define QSERDES_TX_BIST_MODE_LANENO 0x00
+#define QSERDES_TX_DRV_LVL 0x0f
+#define QSERDES_TX_EMP_POST1_LVL 0x01
+#define QSERDES_TX_LANE_MODE 0x08
+
+/* EMAC_QSERDES_COM_SYS_CLK_CTRL */
+#define SYSCLK_CM 0x10
+#define SYSCLK_AC_COUPLE 0x08
+
+/* EMAC_QSERDES_COM_PLL_CNTRL */
+#define OCP_EN 0x20
+#define PLL_DIV_FFEN 0x04
+#define PLL_DIV_ORD 0x02
+
+/* EMAC_QSERDES_COM_SYSCLK_EN_SEL */
+#define SYSCLK_SEL_CMOS 0x8
+
+/* EMAC_QSERDES_COM_RESETSM_CNTRL */
+#define FRQ_TUNE_MODE 0x10
+
+/* EMAC_QSERDES_COM_PLLLOCK_CMP_EN */
+#define PLLLOCK_CMP_EN 0x01
+
+/* EMAC_QSERDES_COM_DEC_START1 */
+#define DEC_START1_MUX 0x80
+
+/* EMAC_QSERDES_COM_DIV_FRAC_START1 */
+#define DIV_FRAC_START1_MUX 0x80
+
+/* EMAC_QSERDES_COM_DIV_FRAC_START2 */
+#define DIV_FRAC_START2_MUX 0x80
+
+/* EMAC_QSERDES_COM_DIV_FRAC_START3 */
+#define DIV_FRAC_START3_MUX 0x10
+
+/* EMAC_QSERDES_COM_DEC_START2 */
+#define DEC_START2_MUX 0x2
+#define DEC_START2 0x1
+
+/* EMAC_QSERDES_COM_RESET_SM */
+#define QSERDES_READY 0x20
+
+/* EMAC_QSERDES_TX_TX_EMP_POST1_LVL */
+#define TX_EMP_POST1_LVL_MUX 0x20
+#define TX_EMP_POST1_LVL_BMSK 0x1f
+#define TX_EMP_POST1_LVL_SHFT 0
+
+/* EMAC_QSERDES_TX_TX_DRV_LVL */
+#define TX_DRV_LVL_MUX 0x10
+#define TX_DRV_LVL_BMSK 0x0f
+#define TX_DRV_LVL_SHFT 0
+
+/* EMAC_QSERDES_TX_TRAN_DRVR_EMP_EN */
+#define EMP_EN_MUX 0x02
+#define EMP_EN 0x01
+
+/* EMAC_QSERDES_RX_CDR_CONTROL & EMAC_QSERDES_RX_CDR_CONTROL2 */
+#define SECONDORDERENABLE 0x40
+#define FIRSTORDER_THRESH_BMSK 0x38
+#define FIRSTORDER_THRESH_SHFT 3
+#define SECONDORDERGAIN_BMSK 0x07
+#define SECONDORDERGAIN_SHFT 0
+
+/* EMAC_QSERDES_RX_RX_EQ_GAIN12 */
+#define RX_EQ_GAIN2_BMSK 0xf0
+#define RX_EQ_GAIN2_SHFT 4
+#define RX_EQ_GAIN1_BMSK 0x0f
+#define RX_EQ_GAIN1_SHFT 0
+
+/* EMAC_SGMII_PHY_SERDES_START */
+#define SERDES_START 0x01
+
+/* EMAC_SGMII_PHY_CMN_PWR_CTRL */
+#define BIAS_EN 0x40
+#define PLL_EN 0x20
+#define SYSCLK_EN 0x10
+#define CLKBUF_L_EN 0x08
+#define PLL_TXCLK_EN 0x02
+#define PLL_RXCLK_EN 0x01
+
+/* EMAC_SGMII_PHY_RX_PWR_CTRL */
+#define L0_RX_SIGDET_EN 0x80
+#define L0_RX_TERM_MODE_BMSK 0x30
+#define L0_RX_TERM_MODE_SHFT 4
+#define L0_RX_I_EN 0x02
+
+/* EMAC_SGMII_PHY_TX_PWR_CTRL */
+#define L0_TX_EN 0x20
+#define L0_CLKBUF_EN 0x10
+#define L0_TRAN_BIAS_EN 0x02
+
+/* EMAC_SGMII_PHY_LANE_CTRL1 */
+#define L0_RX_EQ_EN 0x40
+#define L0_RESET_TSYNC_EN 0x10
+#define L0_DRV_LVL_BMSK 0x0f
+#define L0_DRV_LVL_SHFT 0
+
+/* EMAC_SGMII_PHY_AUTONEG_CFG2 */
+#define FORCE_AN_TX_CFG 0x20
+#define FORCE_AN_RX_CFG 0x10
+#define AN_ENABLE 0x01
+
+/* EMAC_SGMII_PHY_SPEED_CFG1 */
+#define DUPLEX_MODE 0x10
+#define SPDMODE_1000 0x02
+#define SPDMODE_100 0x01
+#define SPDMODE_10 0x00
+#define SPDMODE_BMSK 0x03
+#define SPDMODE_SHFT 0
+
+/* EMAC_SGMII_PHY_POW_DWN_CTRL0 */
+#define PWRDN_B 0x01
+
+/* EMAC_SGMII_PHY_RESET_CTRL */
+#define PHY_SW_RESET 0x01
+
+/* EMAC_SGMII_PHY_IRQ_CMD */
+#define IRQ_GLOBAL_CLEAR 0x01
+
+/* EMAC_SGMII_PHY_INTERRUPT_MASK */
+#define DECODE_CODE_ERR BIT(7)
+#define DECODE_DISP_ERR BIT(6)
+#define PLL_UNLOCK BIT(5)
+#define AN_ILLEGAL_TERM BIT(4)
+#define SYNC_FAIL BIT(3)
+#define AN_START BIT(2)
+#define AN_END BIT(1)
+#define AN_REQUEST BIT(0)
+
+#define SGMII_PHY_IRQ_CLR_WAIT_TIME 10
+
+#define SGMII_PHY_INTERRUPT_ERR (\
+ DECODE_CODE_ERR |\
+ DECODE_DISP_ERR)
+
+#define SGMII_ISR_AN_MASK (\
+ AN_REQUEST |\
+ AN_START |\
+ AN_END |\
+ AN_ILLEGAL_TERM |\
+ PLL_UNLOCK |\
+ SYNC_FAIL)
+
+#define SGMII_ISR_MASK (\
+ SGMII_PHY_INTERRUPT_ERR |\
+ SGMII_ISR_AN_MASK)
+
+/* SGMII TX_CONFIG */
+#define TXCFG_LINK 0x8000
+#define TXCFG_MODE_BMSK 0x1c00
+#define TXCFG_1000_FULL 0x1800
+#define TXCFG_100_FULL 0x1400
+#define TXCFG_100_HALF 0x0400
+#define TXCFG_10_FULL 0x1000
+#define TXCFG_10_HALF 0x0000
+
+#define SERDES_START_WAIT_TIMES 100
+
+#define SGMII_MEM_RES "sgmii"
+#define SGMII_IRQ_RES "sgmii_irq"
+
+struct emac_reg_write {
+ ulong offset;
+#define END_MARKER 0xffffffff
+ u32 val;
+};
+
+static void emac_reg_write_all(void __iomem *base,
+ const struct emac_reg_write *itr, size_t size)
+{
+ size_t i;
+
+ for (i = 0; i < size; ++itr, ++i)
+ writel(itr->val, base + itr->offset);
+}
+
+static const struct emac_reg_write physical_coding_sublayer_programming[] = {
+{EMAC_SGMII_PHY_CDR_CTRL0, SGMII_CDR_MAX_CNT},
+{EMAC_SGMII_PHY_POW_DWN_CTRL0, PWRDN_B},
+{EMAC_SGMII_PHY_CMN_PWR_CTRL, BIAS_EN | SYSCLK_EN | CLKBUF_L_EN |
+ PLL_TXCLK_EN | PLL_RXCLK_EN},
+{EMAC_SGMII_PHY_TX_PWR_CTRL, L0_TX_EN | L0_CLKBUF_EN | L0_TRAN_BIAS_EN},
+{EMAC_SGMII_PHY_RX_PWR_CTRL, L0_RX_SIGDET_EN | (1 << L0_RX_TERM_MODE_SHFT) |
+ L0_RX_I_EN},
+{EMAC_SGMII_PHY_CMN_PWR_CTRL, BIAS_EN | PLL_EN | SYSCLK_EN | CLKBUF_L_EN |
+ PLL_TXCLK_EN | PLL_RXCLK_EN},
+{EMAC_SGMII_PHY_LANE_CTRL1, L0_RX_EQ_EN | L0_RESET_TSYNC_EN |
+ L0_DRV_LVL_BMSK},
+};
+
+static const struct emac_reg_write sysclk_refclk_setting[] = {
+{EMAC_QSERDES_COM_SYSCLK_EN_SEL, SYSCLK_SEL_CMOS},
+{EMAC_QSERDES_COM_SYS_CLK_CTRL, SYSCLK_CM | SYSCLK_AC_COUPLE},
+};
+
+static const struct emac_reg_write pll_setting[] = {
+{EMAC_QSERDES_COM_PLL_IP_SETI, QSERDES_PLL_IPSETI},
+{EMAC_QSERDES_COM_PLL_CP_SETI, QSERDES_PLL_CP_SETI},
+{EMAC_QSERDES_COM_PLL_IP_SETP, QSERDES_PLL_IP_SETP},
+{EMAC_QSERDES_COM_PLL_CP_SETP, QSERDES_PLL_CP_SETP},
+{EMAC_QSERDES_COM_PLL_CRCTRL, QSERDES_PLL_CRCTRL},
+{EMAC_QSERDES_COM_PLL_CNTRL, OCP_EN | PLL_DIV_FFEN | PLL_DIV_ORD},
+{EMAC_QSERDES_COM_DEC_START1, DEC_START1_MUX | QSERDES_PLL_DEC},
+{EMAC_QSERDES_COM_DEC_START2, DEC_START2_MUX | DEC_START2},
+{EMAC_QSERDES_COM_DIV_FRAC_START1, DIV_FRAC_START1_MUX |
+ QSERDES_PLL_DIV_FRAC_START1},
+{EMAC_QSERDES_COM_DIV_FRAC_START2, DIV_FRAC_START2_MUX |
+ QSERDES_PLL_DIV_FRAC_START2},
+{EMAC_QSERDES_COM_DIV_FRAC_START3, DIV_FRAC_START3_MUX |
+ QSERDES_PLL_DIV_FRAC_START3},
+{EMAC_QSERDES_COM_PLLLOCK_CMP1, QSERDES_PLL_LOCK_CMP1},
+{EMAC_QSERDES_COM_PLLLOCK_CMP2, QSERDES_PLL_LOCK_CMP2},
+{EMAC_QSERDES_COM_PLLLOCK_CMP3, QSERDES_PLL_LOCK_CMP3},
+{EMAC_QSERDES_COM_PLLLOCK_CMP_EN, PLLLOCK_CMP_EN},
+{EMAC_QSERDES_COM_RESETSM_CNTRL, FRQ_TUNE_MODE},
+};
+
+static const struct emac_reg_write cdr_setting[] = {
+{EMAC_QSERDES_RX_CDR_CONTROL, SECONDORDERENABLE |
+ (QSERDES_RX_CDR_CTRL1_THRESH << FIRSTORDER_THRESH_SHFT) |
+ (QSERDES_RX_CDR_CTRL1_GAIN << SECONDORDERGAIN_SHFT)},
+{EMAC_QSERDES_RX_CDR_CONTROL2, SECONDORDERENABLE |
+ (QSERDES_RX_CDR_CTRL2_THRESH << FIRSTORDER_THRESH_SHFT) |
+ (QSERDES_RX_CDR_CTRL2_GAIN << SECONDORDERGAIN_SHFT)},
+};
+
+static const struct emac_reg_write tx_rx_setting[] = {
+{EMAC_QSERDES_TX_BIST_MODE_LANENO, QSERDES_TX_BIST_MODE_LANENO},
+{EMAC_QSERDES_TX_TX_DRV_LVL, TX_DRV_LVL_MUX |
+ (QSERDES_TX_DRV_LVL << TX_DRV_LVL_SHFT)},
+{EMAC_QSERDES_TX_TRAN_DRVR_EMP_EN, EMP_EN_MUX | EMP_EN},
+{EMAC_QSERDES_TX_TX_EMP_POST1_LVL, TX_EMP_POST1_LVL_MUX |
+ (QSERDES_TX_EMP_POST1_LVL << TX_EMP_POST1_LVL_SHFT)},
+{EMAC_QSERDES_RX_RX_EQ_GAIN12,
+ (QSERDES_RX_EQ_GAIN2 << RX_EQ_GAIN2_SHFT) |
+ (QSERDES_RX_EQ_GAIN1 << RX_EQ_GAIN1_SHFT)},
+{EMAC_QSERDES_TX_LANE_MODE, QSERDES_TX_LANE_MODE},
+};
+
+int emac_sgmii_link_init(struct emac_adapter *adpt, u32 speed, bool autoneg,
+ bool fc)
+{
+ struct emac_phy *phy = &adpt->phy;
+ u32 val;
+ u32 speed_cfg = 0;
+
+ val = readl(phy->base + EMAC_SGMII_PHY_AUTONEG_CFG2);
+
+ if (autoneg) {
+ val &= ~(FORCE_AN_RX_CFG | FORCE_AN_TX_CFG);
+ val |= AN_ENABLE;
+ writel(val, phy->base + EMAC_SGMII_PHY_AUTONEG_CFG2);
+ } else {
+ switch (speed) {
+ case EMAC_LINK_SPEED_10_HALF:
+ speed_cfg = SPDMODE_10;
+ break;
+ case EMAC_LINK_SPEED_10_FULL:
+ speed_cfg = SPDMODE_10 | DUPLEX_MODE;
+ break;
+ case EMAC_LINK_SPEED_100_HALF:
+ speed_cfg = SPDMODE_100;
+ break;
+ case EMAC_LINK_SPEED_100_FULL:
+ speed_cfg = SPDMODE_100 | DUPLEX_MODE;
+ break;
+ case EMAC_LINK_SPEED_1GB_FULL:
+ speed_cfg = SPDMODE_1000 | DUPLEX_MODE;
+ break;
+ default:
+ return -EINVAL;
+ }
+ val &= ~AN_ENABLE;
+ writel(speed_cfg, phy->base + EMAC_SGMII_PHY_SPEED_CFG1);
+ writel(val, phy->base + EMAC_SGMII_PHY_AUTONEG_CFG2);
+ }
+
+ return 0;
+}
+
+int emac_sgmii_irq_clear(struct emac_adapter *adpt, u32 irq_bits)
+{
+ struct emac_phy *phy = &adpt->phy;
+ u32 status;
+
+ writel_relaxed(irq_bits, phy->base + EMAC_SGMII_PHY_INTERRUPT_CLEAR);
+ writel_relaxed(IRQ_GLOBAL_CLEAR, phy->base + EMAC_SGMII_PHY_IRQ_CMD);
+ /* Ensure interrupt clear command is written to HW */
+ wmb();
+
+ /* After set the IRQ_GLOBAL_CLEAR bit, the status clearing must
+ * be confirmed before clearing the bits in other registers.
+ * It takes a few cycles for hw to clear the interrupt status.
+ */
+ if (readl_poll_timeout_atomic(phy->base +
+ EMAC_SGMII_PHY_INTERRUPT_STATUS,
+ status, !(status & irq_bits), 1,
+ SGMII_PHY_IRQ_CLR_WAIT_TIME)) {
+ netdev_err(adpt->netdev,
+ "error: failed clear SGMII irq: status:0x%x bits:0x%x\n",
+ status, irq_bits);
+ return -EIO;
+ }
+
+ /* Finalize clearing procedure */
+ writel_relaxed(0, phy->base + EMAC_SGMII_PHY_IRQ_CMD);
+ writel_relaxed(0, phy->base + EMAC_SGMII_PHY_INTERRUPT_CLEAR);
+ /* Ensure that clearing procedure finalization is written to HW */
+ wmb();
+
+ return 0;
+}
+
+int emac_sgmii_init(struct emac_adapter *adpt)
+{
+ struct emac_phy *phy = &adpt->phy;
+ int i;
+ int ret;
+
+ ret = emac_sgmii_link_init(adpt, phy->autoneg_advertised, phy->autoneg,
+ !phy->disable_fc_autoneg);
+ if (ret)
+ return ret;
+
+ emac_reg_write_all(phy->base, physical_coding_sublayer_programming,
+ ARRAY_SIZE(physical_coding_sublayer_programming));
+ emac_reg_write_all(phy->base, sysclk_refclk_setting,
+ ARRAY_SIZE(sysclk_refclk_setting));
+ emac_reg_write_all(phy->base, pll_setting, ARRAY_SIZE(pll_setting));
+ emac_reg_write_all(phy->base, cdr_setting, ARRAY_SIZE(cdr_setting));
+ emac_reg_write_all(phy->base, tx_rx_setting,
+ ARRAY_SIZE(tx_rx_setting));
+
+ /* Power up the Ser/Des engine */
+ writel(SERDES_START, phy->base + EMAC_SGMII_PHY_SERDES_START);
+
+ for (i = 0; i < SERDES_START_WAIT_TIMES; i++) {
+ if (readl(phy->base + EMAC_QSERDES_COM_RESET_SM) &
+ QSERDES_READY)
+ break;
+ usleep_range(100, 200);
+ }
+
+ if (i == SERDES_START_WAIT_TIMES) {
+ netdev_err(adpt->netdev, "error: ser/des failed to start\n");
+ return -EIO;
+ }
+ /* Mask out all the SGMII Interrupt */
+ writel(0, phy->base + EMAC_SGMII_PHY_INTERRUPT_MASK);
+
+ emac_sgmii_irq_clear(adpt, SGMII_PHY_INTERRUPT_ERR);
+
+ return 0;
+}
+
+void emac_sgmii_reset_prepare(struct emac_adapter *adpt)
+{
+ struct emac_phy *phy = &adpt->phy;
+ u32 val;
+
+ /* Reset PHY */
+ val = readl(phy->base + EMAC_EMAC_WRAPPER_CSR2);
+ writel(((val & ~PHY_RESET) | PHY_RESET), phy->base +
+ EMAC_EMAC_WRAPPER_CSR2);
+ /* Ensure phy-reset command is written to HW before the release cmd */
+ msleep(50);
+ val = readl(phy->base + EMAC_EMAC_WRAPPER_CSR2);
+ writel((val & ~PHY_RESET), phy->base + EMAC_EMAC_WRAPPER_CSR2);
+ /* Ensure phy-reset release command is written to HW before initializing
+ * SGMII
+ */
+ msleep(50);
+}
+
+void emac_sgmii_reset(struct emac_adapter *adpt)
+{
+ clk_set_rate(adpt->clk[EMAC_CLK_HIGH_SPEED], EMC_CLK_RATE_19_2MHZ);
+ emac_sgmii_reset_prepare(adpt);
+ emac_sgmii_init(adpt);
+ clk_set_rate(adpt->clk[EMAC_CLK_HIGH_SPEED], EMC_CLK_RATE_125MHZ);
+}
+
+int emac_sgmii_no_ephy_link_setup(struct emac_adapter *adpt, u32 speed,
+ bool autoneg)
+{
+ struct emac_phy *phy = &adpt->phy;
+
+ phy->autoneg = autoneg;
+ phy->autoneg_advertised = speed;
+ /* The AN_ENABLE and SPEED_CFG can't change on fly. The SGMII_PHY has
+ * to be re-initialized.
+ */
+ emac_sgmii_reset_prepare(adpt);
+
+ return emac_sgmii_init(adpt);
+}
+
+int emac_sgmii_config(struct platform_device *pdev, struct emac_adapter *adpt)
+{
+ struct emac_phy *phy = &adpt->phy;
+ struct resource *res;
+ int ret;
+
+ ret = platform_get_irq_byname(pdev, SGMII_IRQ_RES);
+ if (ret < 0) {
+ netdev_err(adpt->netdev, "error: missing '%s' resource\n",
+ SGMII_IRQ_RES);
+ return ret;
+ }
+
+ phy->irq = ret;
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, SGMII_MEM_RES);
+ if (!res) {
+ netdev_err(adpt->netdev, "error: missing '%s' resource\n",
+ SGMII_MEM_RES);
+ return -ENXIO;
+ }
+
+ phy->base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(phy->base))
+ return -ENOMEM;
+
+ return 0;
+}
+
+void emac_sgmii_autoneg_check(struct emac_adapter *adpt, u32 *speed,
+ bool *link_up)
+{
+ struct emac_phy *phy = &adpt->phy;
+ u32 autoneg0, autoneg1, status;
+
+ autoneg0 = readl_relaxed(phy->base + EMAC_SGMII_PHY_AUTONEG0_STATUS);
+ autoneg1 = readl_relaxed(phy->base + EMAC_SGMII_PHY_AUTONEG1_STATUS);
+ status = ((autoneg1 & 0xff) << 8) | (autoneg0 & 0xff);
+
+ if (!(status & TXCFG_LINK)) {
+ *link_up = false;
+ *speed = EMAC_LINK_SPEED_UNKNOWN;
+ return;
+ }
+
+ *link_up = true;
+
+ switch (status & TXCFG_MODE_BMSK) {
+ case TXCFG_1000_FULL:
+ *speed = EMAC_LINK_SPEED_1GB_FULL;
+ break;
+ case TXCFG_100_FULL:
+ *speed = EMAC_LINK_SPEED_100_FULL;
+ break;
+ case TXCFG_100_HALF:
+ *speed = EMAC_LINK_SPEED_100_HALF;
+ break;
+ case TXCFG_10_FULL:
+ *speed = EMAC_LINK_SPEED_10_FULL;
+ break;
+ case TXCFG_10_HALF:
+ *speed = EMAC_LINK_SPEED_10_HALF;
+ break;
+ default:
+ *speed = EMAC_LINK_SPEED_UNKNOWN;
+ break;
+ }
+}
+
+void emac_sgmii_no_ephy_link_check(struct emac_adapter *adpt, u32 *speed,
+ bool *link_up)
+{
+ struct emac_phy *phy = &adpt->phy;
+ u32 val;
+
+ val = readl_relaxed(phy->base + EMAC_SGMII_PHY_AUTONEG_CFG2);
+ if (val & AN_ENABLE) {
+ emac_sgmii_autoneg_check(adpt, speed, link_up);
+ return;
+ }
+
+ val = readl_relaxed(phy->base + EMAC_SGMII_PHY_SPEED_CFG1);
+ switch (val & (DUPLEX_MODE | SPDMODE_BMSK)) {
+ case DUPLEX_MODE | SPDMODE_1000:
+ *speed = EMAC_LINK_SPEED_1GB_FULL;
+ break;
+ case DUPLEX_MODE | SPDMODE_100:
+ *speed = EMAC_LINK_SPEED_100_FULL;
+ break;
+ case SPDMODE_100:
+ *speed = EMAC_LINK_SPEED_100_HALF;
+ break;
+ case DUPLEX_MODE | SPDMODE_10:
+ *speed = EMAC_LINK_SPEED_10_FULL;
+ break;
+ case SPDMODE_10:
+ *speed = EMAC_LINK_SPEED_10_HALF;
+ break;
+ default:
+ *speed = EMAC_LINK_SPEED_UNKNOWN;
+ break;
+ }
+ *link_up = true;
+}
+
+irqreturn_t emac_sgmii_isr(int _irq, void *data)
+{
+ struct emac_adapter *adpt = data;
+ struct emac_phy *phy = &adpt->phy;
+ u32 status;
+
+ netif_dbg(adpt, intr, adpt->netdev, "receive sgmii interrupt\n");
+
+ do {
+ status = readl_relaxed(phy->base +
+ EMAC_SGMII_PHY_INTERRUPT_STATUS) &
+ SGMII_ISR_MASK;
+ if (!status)
+ break;
+
+ if (status & SGMII_PHY_INTERRUPT_ERR) {
+ set_bit(EMAC_STATUS_TASK_CHK_SGMII_REQ, &adpt->status);
+ if (!test_bit(EMAC_STATUS_DOWN, &adpt->status))
+ emac_work_thread_reschedule(adpt);
+ }
+
+ if (status & SGMII_ISR_AN_MASK)
+ emac_lsc_schedule_check(adpt);
+
+ if (emac_sgmii_irq_clear(adpt, status) != 0) {
+ /* reset */
+ set_bit(EMAC_STATUS_TASK_REINIT_REQ, &adpt->status);
+ emac_work_thread_reschedule(adpt);
+ break;
+ }
+ } while (1);
+
+ return IRQ_HANDLED;
+}
+
+int emac_sgmii_up(struct emac_adapter *adpt)
+{
+ struct emac_phy *phy = &adpt->phy;
+ int ret;
+
+ ret = request_irq(phy->irq, emac_sgmii_isr, IRQF_TRIGGER_RISING,
+ "sgmii_irq", adpt);
+ if (ret)
+ netdev_err(adpt->netdev,
+ "error:%d on request_irq(%d:sgmii_irq)\n", ret,
+ phy->irq);
+
+ /* enable sgmii irq */
+ writel_relaxed(SGMII_ISR_MASK,
+ phy->base + EMAC_SGMII_PHY_INTERRUPT_MASK);
+
+ return ret;
+}
+
+void emac_sgmii_down(struct emac_adapter *adpt)
+{
+ struct emac_phy *phy = &adpt->phy;
+
+ writel_relaxed(0, phy->base + EMAC_SGMII_PHY_INTERRUPT_MASK);
+ synchronize_irq(phy->irq);
+ free_irq(phy->irq, adpt);
+}
+
+/* Check SGMII for error */
+void emac_sgmii_periodic_check(struct emac_adapter *adpt)
+{
+ struct emac_phy *phy = &adpt->phy;
+
+ if (!test_bit(EMAC_STATUS_TASK_CHK_SGMII_REQ, &adpt->status))
+ return;
+ clear_bit(EMAC_STATUS_TASK_CHK_SGMII_REQ, &adpt->status);
+
+ /* ensure that no reset is in progress while link task is running */
+ while (test_and_set_bit(EMAC_STATUS_RESETTING, &adpt->status))
+ msleep(20); /* Reset might take few 10s of ms */
+
+ if (test_bit(EMAC_STATUS_DOWN, &adpt->status))
+ goto sgmii_task_done;
+
+ if (readl_relaxed(phy->base + EMAC_SGMII_PHY_RX_CHK_STATUS) & 0x40)
+ goto sgmii_task_done;
+
+ netdev_err(adpt->netdev, "error: SGMII CDR not locked\n");
+
+sgmii_task_done:
+ clear_bit(EMAC_STATUS_RESETTING, &adpt->status);
+}
diff --git a/drivers/net/ethernet/qualcomm/emac/emac-sgmii.h b/drivers/net/ethernet/qualcomm/emac/emac-sgmii.h
new file mode 100644
index 0000000..4d55915b
--- /dev/null
+++ b/drivers/net/ethernet/qualcomm/emac/emac-sgmii.h
@@ -0,0 +1,30 @@
+/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _EMAC_SGMII_H_
+#define _EMAC_SGMII_H_
+
+struct emac_adapter;
+struct platform_device;
+
+int emac_sgmii_init(struct emac_adapter *adpt);
+int emac_sgmii_config(struct platform_device *pdev, struct emac_adapter *adpt);
+void emac_sgmii_reset(struct emac_adapter *adpt);
+int emac_sgmii_up(struct emac_adapter *adpt);
+void emac_sgmii_down(struct emac_adapter *adpt);
+void emac_sgmii_periodic_check(struct emac_adapter *adpt);
+int emac_sgmii_no_ephy_link_setup(struct emac_adapter *adpt, u32 speed,
+ bool autoneg);
+void emac_sgmii_no_ephy_link_check(struct emac_adapter *adpt, u32 *speed,
+ bool *link_up);
+
+#endif /*_EMAC_SGMII_H_*/
diff --git a/drivers/net/ethernet/qualcomm/emac/emac.c b/drivers/net/ethernet/qualcomm/emac/emac.c
new file mode 100644
index 0000000..17383f8
--- /dev/null
+++ b/drivers/net/ethernet/qualcomm/emac/emac.c
@@ -0,0 +1,1228 @@
+/* Copyright (c) 2013-2015, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+/* Qualcomm Technologies, Inc. EMAC Gigabit Ethernet Driver
+ * The EMAC driver supports following features:
+ * 1) Receive Side Scaling (RSS).
+ * 2) Checksum offload.
+ * 3) Multiple PHY support on MDIO bus.
+ * 4) Runtime power management support.
+ * 5) Interrupt coalescing support.
+ * 6) SGMII phy.
+ * 7) SGMII direct connection (without external phy).
+ */
+
+#include <linux/if_ether.h>
+#include <linux/if_vlan.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_net.h>
+#include <linux/of_gpio.h>
+#include <linux/phy.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include "emac.h"
+#include "emac-mac.h"
+#include "emac-phy.h"
+#include "emac-sgmii.h"
+
+#define DRV_VERSION "1.3.0.0"
+
+static int debug = -1;
+module_param(debug, int, S_IRUGO | S_IWUSR | S_IWGRP);
+
+static int emac_irq_use_extended;
+module_param(emac_irq_use_extended, int, S_IRUGO | S_IWUSR | S_IWGRP);
+
+const char emac_drv_name[] = "qcom-emac";
+const char emac_drv_description[] =
+ "Qualcomm Technologies, Inc. EMAC Ethernet Driver";
+const char emac_drv_version[] = DRV_VERSION;
+
+#define EMAC_MSG_DEFAULT (NETIF_MSG_DRV | NETIF_MSG_PROBE | NETIF_MSG_LINK | \
+ NETIF_MSG_TIMER | NETIF_MSG_IFDOWN | NETIF_MSG_IFUP | \
+ NETIF_MSG_RX_ERR | NETIF_MSG_TX_ERR | NETIF_MSG_TX_QUEUED | \
+ NETIF_MSG_INTR | NETIF_MSG_TX_DONE | NETIF_MSG_RX_STATUS | \
+ NETIF_MSG_PKTDATA | NETIF_MSG_HW | NETIF_MSG_WOL)
+
+#define EMAC_RRD_SIZE 4
+#define EMAC_TS_RRD_SIZE 6
+#define EMAC_TPD_SIZE 4
+#define EMAC_RFD_SIZE 2
+
+#define REG_MAC_RX_STATUS_BIN EMAC_RXMAC_STATC_REG0
+#define REG_MAC_RX_STATUS_END EMAC_RXMAC_STATC_REG22
+#define REG_MAC_TX_STATUS_BIN EMAC_TXMAC_STATC_REG0
+#define REG_MAC_TX_STATUS_END EMAC_TXMAC_STATC_REG24
+
+#define RXQ0_NUM_RFD_PREF_DEF 8
+#define TXQ0_NUM_TPD_PREF_DEF 5
+
+#define EMAC_PREAMBLE_DEF 7
+
+#define DMAR_DLY_CNT_DEF 15
+#define DMAW_DLY_CNT_DEF 4
+
+#define IMR_NORMAL_MASK (\
+ ISR_ERROR |\
+ ISR_GPHY_LINK |\
+ ISR_TX_PKT |\
+ GPHY_WAKEUP_INT)
+
+#define IMR_EXTENDED_MASK (\
+ SW_MAN_INT |\
+ ISR_OVER |\
+ ISR_ERROR |\
+ ISR_GPHY_LINK |\
+ ISR_TX_PKT |\
+ GPHY_WAKEUP_INT)
+
+#define ISR_TX_PKT (\
+ TX_PKT_INT |\
+ TX_PKT_INT1 |\
+ TX_PKT_INT2 |\
+ TX_PKT_INT3)
+
+#define ISR_GPHY_LINK (\
+ GPHY_LINK_UP_INT |\
+ GPHY_LINK_DOWN_INT)
+
+#define ISR_OVER (\
+ RFD0_UR_INT |\
+ RFD1_UR_INT |\
+ RFD2_UR_INT |\
+ RFD3_UR_INT |\
+ RFD4_UR_INT |\
+ RXF_OF_INT |\
+ TXF_UR_INT)
+
+#define ISR_ERROR (\
+ DMAR_TO_INT |\
+ DMAW_TO_INT |\
+ TXQ_TO_INT)
+
+const char * const emac_gpio_name[] = {
+ "qcom,emac-gpio-mdc", "qcom,emac-gpio-mdio"
+};
+
+/* in sync with enum emac_clk_id */
+static const char * const emac_clk_name[] = {
+ "axi_clk", "cfg_ahb_clk", "high_speed_clk", "mdio_clk", "tx_clk",
+ "rx_clk", "sys_clk"
+};
+
+void emac_reg_update32(void __iomem *addr, u32 mask, u32 val)
+{
+ u32 data = readl(addr);
+
+ writel(((data & ~mask) | val), addr);
+}
+
+/* reinitialize */
+void emac_reinit_locked(struct emac_adapter *adpt)
+{
+ WARN_ON(in_interrupt());
+
+ while (test_and_set_bit(EMAC_STATUS_RESETTING, &adpt->status))
+ msleep(20); /* Reset might take few 10s of ms */
+
+ if (test_bit(EMAC_STATUS_DOWN, &adpt->status)) {
+ clear_bit(EMAC_STATUS_RESETTING, &adpt->status);
+ return;
+ }
+
+ emac_mac_down(adpt, true);
+
+ emac_sgmii_reset(adpt);
+ emac_mac_up(adpt);
+
+ clear_bit(EMAC_STATUS_RESETTING, &adpt->status);
+}
+
+void emac_work_thread_reschedule(struct emac_adapter *adpt)
+{
+ if (!test_bit(EMAC_STATUS_DOWN, &adpt->status) &&
+ !test_bit(EMAC_STATUS_WATCH_DOG, &adpt->status)) {
+ set_bit(EMAC_STATUS_WATCH_DOG, &adpt->status);
+ schedule_work(&adpt->work_thread);
+ }
+}
+
+void emac_lsc_schedule_check(struct emac_adapter *adpt)
+{
+ set_bit(EMAC_STATUS_TASK_LSC_REQ, &adpt->status);
+ adpt->link_chk_timeout = jiffies + EMAC_TRY_LINK_TIMEOUT;
+
+ if (!test_bit(EMAC_STATUS_DOWN, &adpt->status))
+ emac_work_thread_reschedule(adpt);
+}
+
+/* Change MAC address */
+static int emac_set_mac_address(struct net_device *netdev, void *p)
+{
+ struct emac_adapter *adpt = netdev_priv(netdev);
+
+ struct sockaddr *addr = p;
+
+ if (!is_valid_ether_addr(addr->sa_data))
+ return -EADDRNOTAVAIL;
+
+ if (netif_running(netdev))
+ return -EBUSY;
+
+ memcpy(netdev->dev_addr, addr->sa_data, netdev->addr_len);
+ memcpy(adpt->mac_addr, addr->sa_data, netdev->addr_len);
+
+ emac_mac_addr_clear(adpt, adpt->mac_addr);
+
+ return 0;
+}
+
+/* NAPI */
+static int emac_napi_rtx(struct napi_struct *napi, int budget)
+{
+ struct emac_rx_queue *rx_q = container_of(napi, struct emac_rx_queue,
+ napi);
+ struct emac_adapter *adpt = netdev_priv(rx_q->netdev);
+ struct emac_irq *irq = rx_q->irq;
+
+ int work_done = 0;
+
+ /* Keep link state information with original netdev */
+ if (!netif_carrier_ok(adpt->netdev))
+ goto quit_polling;
+
+ emac_mac_rx_process(adpt, rx_q, &work_done, budget);
+
+ if (work_done < budget) {
+quit_polling:
+ napi_complete(napi);
+
+ irq->mask |= rx_q->intr;
+ writel(irq->mask, adpt->base + EMAC_INT_MASK);
+ }
+
+ return work_done;
+}
+
+/* Transmit the packet */
+static int emac_start_xmit(struct sk_buff *skb, struct net_device *netdev)
+{
+ struct emac_adapter *adpt = netdev_priv(netdev);
+
+ return emac_mac_tx_buf_send(adpt, &adpt->tx_q, skb);
+}
+
+irqreturn_t emac_isr(int _irq, void *data)
+{
+ struct emac_irq *irq = data;
+ struct emac_adapter *adpt = container_of(irq, struct emac_adapter, irq);
+ struct emac_rx_queue *rx_q = &adpt->rx_q;
+
+ int max_ints = 1;
+ u32 isr, status;
+
+ /* disable the interrupt */
+ writel(0, adpt->base + EMAC_INT_MASK);
+
+ do {
+ isr = readl_relaxed(adpt->base + EMAC_INT_STATUS);
+ status = isr & irq->mask;
+
+ if (status == 0)
+ break;
+
+ if (status & ISR_ERROR) {
+ netif_warn(adpt, intr, adpt->netdev,
+ "warning: error irq status 0x%lx\n",
+ status & ISR_ERROR);
+ /* reset MAC */
+ set_bit(EMAC_STATUS_TASK_REINIT_REQ, &adpt->status);
+ emac_work_thread_reschedule(adpt);
+ }
+
+ /* Schedule the napi for receive queue with interrupt
+ * status bit set
+ */
+ if ((status & rx_q->intr)) {
+ if (napi_schedule_prep(&rx_q->napi)) {
+ irq->mask &= ~rx_q->intr;
+ __napi_schedule(&rx_q->napi);
+ }
+ }
+
+ if (status & TX_PKT_INT)
+ emac_mac_tx_process(adpt, &adpt->tx_q);
+
+ if (status & ISR_OVER)
+ netif_warn(adpt, intr, adpt->netdev,
+ "warning: TX/RX overflow status 0x%lx\n",
+ status & ISR_OVER);
+
+ /* link event */
+ if (status & (ISR_GPHY_LINK | SW_MAN_INT)) {
+ emac_lsc_schedule_check(adpt);
+ break;
+ }
+ } while (--max_ints > 0);
+
+ /* enable the interrupt */
+ writel(irq->mask, adpt->base + EMAC_INT_MASK);
+
+ return IRQ_HANDLED;
+}
+
+/* Configure VLAN tag strip/insert feature */
+static int emac_set_features(struct net_device *netdev,
+ netdev_features_t features)
+{
+ struct emac_adapter *adpt = netdev_priv(netdev);
+
+ netdev_features_t changed = features ^ netdev->features;
+
+ if (!(changed & (NETIF_F_HW_VLAN_CTAG_TX | NETIF_F_HW_VLAN_CTAG_RX)))
+ return 0;
+
+ netdev->features = features;
+ if (netdev->features & NETIF_F_HW_VLAN_CTAG_RX)
+ set_bit(EMAC_STATUS_VLANSTRIP_EN, &adpt->status);
+ else
+ clear_bit(EMAC_STATUS_VLANSTRIP_EN, &adpt->status);
+
+ if (netif_running(netdev))
+ emac_reinit_locked(adpt);
+
+ return 0;
+}
+
+/* Configure Multicast and Promiscuous modes */
+void emac_rx_mode_set(struct net_device *netdev)
+{
+ struct emac_adapter *adpt = netdev_priv(netdev);
+
+ struct netdev_hw_addr *ha;
+
+ /* Check for Promiscuous and All Multicast modes */
+ if (netdev->flags & IFF_PROMISC) {
+ set_bit(EMAC_STATUS_PROMISC_EN, &adpt->status);
+ } else if (netdev->flags & IFF_ALLMULTI) {
+ set_bit(EMAC_STATUS_MULTIALL_EN, &adpt->status);
+ clear_bit(EMAC_STATUS_PROMISC_EN, &adpt->status);
+ } else {
+ clear_bit(EMAC_STATUS_MULTIALL_EN, &adpt->status);
+ clear_bit(EMAC_STATUS_PROMISC_EN, &adpt->status);
+ }
+ emac_mac_mode_config(adpt);
+
+ /* update multicast address filtering */
+ emac_mac_multicast_addr_clear(adpt);
+ netdev_for_each_mc_addr(ha, netdev)
+ emac_mac_multicast_addr_set(adpt, ha->addr);
+}
+
+/* Change the Maximum Transfer Unit (MTU) */
+static int emac_change_mtu(struct net_device *netdev, int new_mtu)
+{
+ struct emac_adapter *adpt = netdev_priv(netdev);
+ int old_mtu = netdev->mtu;
+ int max_frame = new_mtu + ETH_HLEN + ETH_FCS_LEN + VLAN_HLEN;
+
+ if ((max_frame < EMAC_MIN_ETH_FRAME_SIZE) ||
+ (max_frame > EMAC_MAX_ETH_FRAME_SIZE)) {
+ netdev_err(adpt->netdev, "error: invalid MTU setting\n");
+ return -EINVAL;
+ }
+
+ if ((old_mtu != new_mtu) && netif_running(netdev)) {
+ netif_info(adpt, hw, adpt->netdev,
+ "changing MTU from %d to %d\n", netdev->mtu,
+ new_mtu);
+ netdev->mtu = new_mtu;
+ adpt->mtu = new_mtu;
+ adpt->rxbuf_size = new_mtu > EMAC_DEF_RX_BUF_SIZE ?
+ ALIGN(max_frame, 8) : EMAC_DEF_RX_BUF_SIZE;
+ emac_reinit_locked(adpt);
+ }
+
+ return 0;
+}
+
+/* Called when the network interface is made active */
+static int emac_open(struct net_device *netdev)
+{
+ struct emac_adapter *adpt = netdev_priv(netdev);
+ int ret;
+
+ netif_carrier_off(netdev);
+
+ /* allocate rx/tx dma buffer & descriptors */
+ ret = emac_mac_rx_tx_rings_alloc_all(adpt);
+ if (ret) {
+ netdev_err(adpt->netdev, "error allocating rx/tx rings\n");
+ return ret;
+ }
+
+ pm_runtime_set_active(netdev->dev.parent);
+ pm_runtime_enable(netdev->dev.parent);
+
+ ret = emac_mac_up(adpt);
+ if (ret)
+ emac_mac_rx_tx_rings_free_all(adpt);
+
+ return ret;
+}
+
+/* Called when the network interface is disabled */
+static int emac_close(struct net_device *netdev)
+{
+ struct emac_adapter *adpt = netdev_priv(netdev);
+
+ /* ensure no task is running and no reset is in progress */
+ while (test_and_set_bit(EMAC_STATUS_RESETTING, &adpt->status))
+ msleep(20); /* Reset might take few 10s of ms */
+
+ pm_runtime_disable(netdev->dev.parent);
+ if (!test_bit(EMAC_STATUS_DOWN, &adpt->status))
+ emac_mac_down(adpt, true);
+ else
+ emac_mac_reset(adpt);
+
+ emac_mac_rx_tx_rings_free_all(adpt);
+
+ clear_bit(EMAC_STATUS_RESETTING, &adpt->status);
+
+ return 0;
+}
+
+/* PHY related IOCTLs */
+static int emac_mii_ioctl(struct net_device *netdev,
+ struct ifreq *ifr, int cmd)
+{
+ struct emac_adapter *adpt = netdev_priv(netdev);
+ struct emac_phy *phy = &adpt->phy;
+ struct mii_ioctl_data *data = if_mii(ifr);
+
+ switch (cmd) {
+ case SIOCGMIIPHY:
+ data->phy_id = phy->addr;
+ return 0;
+
+ case SIOCGMIIREG:
+ if (!capable(CAP_NET_ADMIN))
+ return -EPERM;
+
+ if (data->reg_num & ~(0x1F))
+ return -EFAULT;
+
+ if (data->phy_id >= PHY_MAX_ADDR)
+ return -EFAULT;
+
+ if (phy->external && data->phy_id != phy->addr)
+ return -EFAULT;
+
+ return emac_phy_read(adpt, data->phy_id, data->reg_num,
+ &data->val_out);
+
+ case SIOCSMIIREG:
+ if (!capable(CAP_NET_ADMIN))
+ return -EPERM;
+
+ if (data->reg_num & ~(0x1F))
+ return -EFAULT;
+
+ if (data->phy_id >= PHY_MAX_ADDR)
+ return -EFAULT;
+
+ if (phy->external && data->phy_id != phy->addr)
+ return -EFAULT;
+
+ return emac_phy_write(adpt, data->phy_id, data->reg_num,
+ data->val_in);
+ default:
+ return -EFAULT;
+ }
+}
+
+/* Respond to a TX hang */
+static void emac_tx_timeout(struct net_device *netdev)
+{
+ struct emac_adapter *adpt = netdev_priv(netdev);
+
+ if (!test_bit(EMAC_STATUS_DOWN, &adpt->status)) {
+ set_bit(EMAC_STATUS_TASK_REINIT_REQ, &adpt->status);
+ emac_work_thread_reschedule(adpt);
+ }
+}
+
+/* IOCTL support for the interface */
+static int emac_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd)
+{
+ switch (cmd) {
+ case SIOCGMIIPHY:
+ case SIOCGMIIREG:
+ case SIOCSMIIREG:
+ return emac_mii_ioctl(netdev, ifr, cmd);
+ default:
+ return -EOPNOTSUPP;
+ }
+}
+
+/* Provide network statistics info for the interface */
+struct rtnl_link_stats64 *emac_get_stats64(struct net_device *netdev,
+ struct rtnl_link_stats64 *net_stats)
+{
+ struct emac_adapter *adpt = netdev_priv(netdev);
+ struct emac_stats *stats = &adpt->stats;
+ u16 addr = REG_MAC_RX_STATUS_BIN;
+ u64 *stats_itr = &adpt->stats.rx_ok;
+ u32 val;
+
+ while (addr <= REG_MAC_RX_STATUS_END) {
+ val = readl_relaxed(adpt->base + addr);
+ *stats_itr += val;
+ ++stats_itr;
+ addr += sizeof(u32);
+ }
+
+ /* additional rx status */
+ val = readl_relaxed(adpt->base + EMAC_RXMAC_STATC_REG23);
+ adpt->stats.rx_crc_align += val;
+ val = readl_relaxed(adpt->base + EMAC_RXMAC_STATC_REG24);
+ adpt->stats.rx_jubbers += val;
+
+ /* update tx status */
+ addr = REG_MAC_TX_STATUS_BIN;
+ stats_itr = &adpt->stats.tx_ok;
+
+ while (addr <= REG_MAC_TX_STATUS_END) {
+ val = readl_relaxed(adpt->base + addr);
+ *stats_itr += val;
+ ++stats_itr;
+ addr += sizeof(u32);
+ }
+
+ /* additional tx status */
+ val = readl_relaxed(adpt->base + EMAC_TXMAC_STATC_REG25);
+ adpt->stats.tx_col += val;
+
+ /* return parsed statistics */
+ net_stats->rx_packets = stats->rx_ok;
+ net_stats->tx_packets = stats->tx_ok;
+ net_stats->rx_bytes = stats->rx_byte_cnt;
+ net_stats->tx_bytes = stats->tx_byte_cnt;
+ net_stats->multicast = stats->rx_mcast;
+ net_stats->collisions = stats->tx_1_col + stats->tx_2_col * 2 +
+ stats->tx_late_col + stats->tx_abort_col;
+
+ net_stats->rx_errors = stats->rx_frag + stats->rx_fcs_err +
+ stats->rx_len_err + stats->rx_sz_ov +
+ stats->rx_align_err;
+ net_stats->rx_fifo_errors = stats->rx_rxf_ov;
+ net_stats->rx_length_errors = stats->rx_len_err;
+ net_stats->rx_crc_errors = stats->rx_fcs_err;
+ net_stats->rx_frame_errors = stats->rx_align_err;
+ net_stats->rx_over_errors = stats->rx_rxf_ov;
+ net_stats->rx_missed_errors = stats->rx_rxf_ov;
+
+ net_stats->tx_errors = stats->tx_late_col + stats->tx_abort_col +
+ stats->tx_underrun + stats->tx_trunc;
+ net_stats->tx_fifo_errors = stats->tx_underrun;
+ net_stats->tx_aborted_errors = stats->tx_abort_col;
+ net_stats->tx_window_errors = stats->tx_late_col;
+
+ return net_stats;
+}
+
+static const struct net_device_ops emac_netdev_ops = {
+ .ndo_open = &emac_open,
+ .ndo_stop = &emac_close,
+ .ndo_validate_addr = ð_validate_addr,
+ .ndo_start_xmit = &emac_start_xmit,
+ .ndo_set_mac_address = &emac_set_mac_address,
+ .ndo_change_mtu = &emac_change_mtu,
+ .ndo_do_ioctl = &emac_ioctl,
+ .ndo_tx_timeout = &emac_tx_timeout,
+ .ndo_get_stats64 = &emac_get_stats64,
+ .ndo_set_features = emac_set_features,
+ .ndo_set_rx_mode = emac_rx_mode_set,
+};
+
+static char *emac_link_speed_to_str(u32 speed)
+{
+ switch (speed) {
+ case EMAC_LINK_SPEED_1GB_FULL:
+ return "1 Gbps Duplex Full";
+ case EMAC_LINK_SPEED_100_FULL:
+ return "100 Mbps Duplex Full";
+ case EMAC_LINK_SPEED_100_HALF:
+ return "100 Mbps Duplex Half";
+ case EMAC_LINK_SPEED_10_FULL:
+ return "10 Mbps Duplex Full";
+ case EMAC_LINK_SPEED_10_HALF:
+ return "10 Mbps Duplex HALF";
+ default:
+ return "unknown speed";
+ }
+}
+
+/* Check link status and handle link state changes */
+static void emac_work_thread_link_check(struct emac_adapter *adpt)
+{
+ struct net_device *netdev = adpt->netdev;
+ struct emac_phy *phy = &adpt->phy;
+ const char *speed;
+
+ if (!test_bit(EMAC_STATUS_TASK_LSC_REQ, &adpt->status))
+ return;
+ clear_bit(EMAC_STATUS_TASK_LSC_REQ, &adpt->status);
+
+ /* ensure that no reset is in progress while link task is running */
+ while (test_and_set_bit(EMAC_STATUS_RESETTING, &adpt->status))
+ msleep(20); /* Reset might take few 10s of ms */
+
+ if (test_bit(EMAC_STATUS_DOWN, &adpt->status))
+ goto link_task_done;
+
+ emac_phy_link_check(adpt, &phy->link_speed, &phy->link_up);
+ speed = emac_link_speed_to_str(phy->link_speed);
+
+ if (phy->link_up) {
+ if (netif_carrier_ok(netdev))
+ goto link_task_done;
+
+ pm_runtime_get_sync(netdev->dev.parent);
+ netif_info(adpt, timer, adpt->netdev, "NIC Link is Up %s\n",
+ speed);
+
+ emac_mac_start(adpt);
+ netif_carrier_on(netdev);
+ netif_wake_queue(netdev);
+ } else {
+ if (time_after(adpt->link_chk_timeout, jiffies))
+ set_bit(EMAC_STATUS_TASK_LSC_REQ, &adpt->status);
+
+ /* only continue if link was up previously */
+ if (!netif_carrier_ok(netdev))
+ goto link_task_done;
+
+ phy->link_speed = 0;
+ netif_info(adpt, timer, adpt->netdev, "NIC Link is Down\n");
+ netif_stop_queue(netdev);
+ netif_carrier_off(netdev);
+
+ emac_mac_stop(adpt);
+ pm_runtime_put_sync(netdev->dev.parent);
+ }
+
+ /* link state transition, kick timer */
+ mod_timer(&adpt->timers, jiffies);
+
+link_task_done:
+ clear_bit(EMAC_STATUS_RESETTING, &adpt->status);
+}
+
+/* Watchdog task routine */
+static void emac_work_thread(struct work_struct *work)
+{
+ struct emac_adapter *adpt = container_of(work, struct emac_adapter,
+ work_thread);
+
+ if (!test_bit(EMAC_STATUS_WATCH_DOG, &adpt->status))
+ netif_warn(adpt, timer, adpt->netdev,
+ "warning: WATCH_DOG flag isn't set\n");
+
+ if (test_bit(EMAC_STATUS_TASK_REINIT_REQ, &adpt->status)) {
+ clear_bit(EMAC_STATUS_TASK_REINIT_REQ, &adpt->status);
+
+ if ((!test_bit(EMAC_STATUS_DOWN, &adpt->status)) &&
+ (!test_bit(EMAC_STATUS_RESETTING, &adpt->status)))
+ emac_reinit_locked(adpt);
+ }
+
+ emac_work_thread_link_check(adpt);
+ emac_sgmii_periodic_check(adpt);
+ clear_bit(EMAC_STATUS_WATCH_DOG, &adpt->status);
+}
+
+/* Timer routine */
+static void emac_timer_thread(unsigned long data)
+{
+ struct emac_adapter *adpt = (struct emac_adapter *)data;
+ unsigned long delay;
+
+ if (pm_runtime_status_suspended(adpt->netdev->dev.parent))
+ return;
+
+ /* poll faster when waiting for link */
+ if (test_bit(EMAC_STATUS_TASK_LSC_REQ, &adpt->status))
+ delay = HZ / 10;
+ else
+ delay = 2 * HZ;
+
+ /* Reset the timer */
+ mod_timer(&adpt->timers, delay + jiffies);
+
+ emac_work_thread_reschedule(adpt);
+}
+
+/* Initialize various data structures */
+static void emac_init_adapter(struct emac_adapter *adpt)
+{
+ struct emac_phy *phy = &adpt->phy;
+ int max_frame;
+ u32 reg;
+
+ /* ids */
+ reg = readl_relaxed(adpt->base + EMAC_DMA_MAS_CTRL);
+ adpt->devid = (reg & DEV_ID_NUM_BMSK) >> DEV_ID_NUM_SHFT;
+ adpt->revid = (reg & DEV_REV_NUM_BMSK) >> DEV_REV_NUM_SHFT;
+
+ /* descriptors */
+ adpt->tx_desc_cnt = EMAC_DEF_TX_DESCS;
+ adpt->rx_desc_cnt = EMAC_DEF_RX_DESCS;
+
+ /* mtu */
+ adpt->netdev->mtu = ETH_DATA_LEN;
+ adpt->mtu = adpt->netdev->mtu;
+ max_frame = adpt->netdev->mtu + ETH_HLEN + ETH_FCS_LEN + VLAN_HLEN;
+ adpt->rxbuf_size = adpt->netdev->mtu > EMAC_DEF_RX_BUF_SIZE ?
+ ALIGN(max_frame, 8) : EMAC_DEF_RX_BUF_SIZE;
+
+ /* dma */
+ adpt->dma_order = emac_dma_ord_out;
+ adpt->dmar_block = emac_dma_req_4096;
+ adpt->dmaw_block = emac_dma_req_128;
+ adpt->dmar_dly_cnt = DMAR_DLY_CNT_DEF;
+ adpt->dmaw_dly_cnt = DMAW_DLY_CNT_DEF;
+ adpt->tpd_burst = TXQ0_NUM_TPD_PREF_DEF;
+ adpt->rfd_burst = RXQ0_NUM_RFD_PREF_DEF;
+
+ /* link */
+ phy->link_up = false;
+ phy->link_speed = EMAC_LINK_SPEED_UNKNOWN;
+
+ /* flow control */
+ phy->req_fc_mode = EMAC_FC_FULL;
+ phy->cur_fc_mode = EMAC_FC_FULL;
+ phy->disable_fc_autoneg = false;
+
+ /* irq moderator */
+ reg = ((EMAC_DEF_RX_IRQ_MOD >> 1) << IRQ_MODERATOR2_INIT_SHFT) |
+ ((EMAC_DEF_TX_IRQ_MOD >> 1) << IRQ_MODERATOR_INIT_SHFT);
+ adpt->irq_mod = reg;
+
+ /* others */
+ adpt->preamble = EMAC_PREAMBLE_DEF;
+}
+
+#ifdef CONFIG_PM
+static int emac_runtime_suspend(struct device *device)
+{
+ struct platform_device *pdev = to_platform_device(device);
+ struct net_device *netdev = dev_get_drvdata(&pdev->dev);
+ struct emac_adapter *adpt = netdev_priv(netdev);
+
+ emac_mac_pm(adpt);
+
+ return 0;
+}
+
+static int emac_runtime_idle(struct device *device)
+{
+ struct platform_device *pdev = to_platform_device(device);
+ struct net_device *netdev = dev_get_drvdata(&pdev->dev);
+
+ /* schedule to enter runtime suspend state if the link does
+ * not come back up within the specified time
+ */
+ pm_schedule_suspend(netdev->dev.parent,
+ jiffies_to_msecs(EMAC_TRY_LINK_TIMEOUT));
+
+ return -EBUSY;
+}
+#endif /* CONFIG_PM */
+
+#ifdef CONFIG_PM_SLEEP
+static int emac_suspend(struct device *device)
+{
+ struct platform_device *pdev = to_platform_device(device);
+ struct net_device *netdev = dev_get_drvdata(&pdev->dev);
+ struct emac_adapter *adpt = netdev_priv(netdev);
+ struct emac_phy *phy = &adpt->phy;
+ int i;
+ u32 speed, adv_speed;
+ bool link_up = false;
+ int ret = 0;
+
+ netif_device_detach(netdev);
+ if (netif_running(netdev)) {
+ /* ensure no task is running and no reset is in progress */
+ while (test_and_set_bit(EMAC_STATUS_RESETTING, &adpt->status))
+ msleep(20); /* Reset might take few 10s of ms */
+
+ emac_mac_down(adpt, false);
+
+ clear_bit(EMAC_STATUS_RESETTING, &adpt->status);
+ }
+
+ emac_phy_link_check(adpt, &speed, &link_up);
+
+ if (link_up) {
+ adv_speed = EMAC_LINK_SPEED_10_HALF;
+ emac_phy_link_speed_get(adpt, &adv_speed);
+
+ ret = emac_phy_link_setup(adpt, adv_speed, true,
+ !adpt->phy.disable_fc_autoneg);
+ if (ret)
+ return ret;
+
+ link_up = false;
+ for (i = 0; i < EMAC_MAX_SETUP_LNK_CYCLE; i++) {
+ ret = emac_phy_link_check(adpt, &speed, &link_up);
+ if ((!ret) && link_up)
+ break;
+
+ /* link can take upto few seconds to come up */
+ msleep(100);
+ }
+ }
+
+ if (!link_up)
+ speed = EMAC_LINK_SPEED_10_HALF;
+
+ phy->link_speed = speed;
+ phy->link_up = link_up;
+
+ emac_mac_pm(adpt);
+
+ return 0;
+}
+
+static int emac_resume(struct device *device)
+{
+ struct platform_device *pdev = to_platform_device(device);
+ struct net_device *netdev = dev_get_drvdata(&pdev->dev);
+ struct emac_adapter *adpt = netdev_priv(netdev);
+ struct emac_phy *phy = &adpt->phy;
+ u32 ret;
+
+ emac_mac_reset(adpt);
+ ret = emac_phy_link_setup(adpt, phy->autoneg_advertised, true,
+ !phy->disable_fc_autoneg);
+ if (ret)
+ return ret;
+
+ if (netif_running(netdev)) {
+ ret = emac_mac_up(adpt);
+ if (ret)
+ return ret;
+ }
+
+ netif_device_attach(netdev);
+
+ return 0;
+}
+#endif /* CONFIG_PM_SLEEP */
+
+/* Get the clock */
+static int emac_clks_get(struct platform_device *pdev,
+ struct emac_adapter *adpt)
+{
+ struct clk *clk;
+ int i;
+
+ for (i = 0; i < EMAC_CLK_CNT; i++) {
+ clk = clk_get(&pdev->dev, emac_clk_name[i]);
+
+ if (IS_ERR(clk)) {
+ netdev_err(adpt->netdev, "error:%ld on clk_get(%s)\n",
+ PTR_ERR(clk), emac_clk_name[i]);
+
+ while (--i >= 0)
+ if (adpt->clk[i]) {
+ clk_put(adpt->clk[i]);
+ adpt->clk[i] = NULL;
+ }
+ return PTR_ERR(clk);
+ }
+
+ adpt->clk[i] = clk;
+ }
+
+ return 0;
+}
+
+/* Initialize clocks */
+static int emac_clks_phase1_init(struct emac_adapter *adpt)
+{
+ int ret;
+
+ ret = clk_prepare_enable(adpt->clk[EMAC_CLK_AXI]);
+ if (ret)
+ return ret;
+
+ ret = clk_prepare_enable(adpt->clk[EMAC_CLK_CFG_AHB]);
+ if (ret)
+ return ret;
+
+ ret = clk_set_rate(adpt->clk[EMAC_CLK_HIGH_SPEED],
+ EMC_CLK_RATE_19_2MHZ);
+ if (ret)
+ return ret;
+
+ return clk_prepare_enable(adpt->clk[EMAC_CLK_HIGH_SPEED]);
+}
+
+/* Enable clocks; needs emac_clks_phase1_init to be called before */
+static int emac_clks_phase2_init(struct emac_adapter *adpt)
+{
+ int ret;
+
+ ret = clk_set_rate(adpt->clk[EMAC_CLK_TX], EMC_CLK_RATE_125MHZ);
+ if (ret)
+ return ret;
+
+ ret = clk_prepare_enable(adpt->clk[EMAC_CLK_TX]);
+ if (ret)
+ return ret;
+
+ ret = clk_set_rate(adpt->clk[EMAC_CLK_HIGH_SPEED], EMC_CLK_RATE_125MHZ);
+ if (ret)
+ return ret;
+
+ ret = clk_set_rate(adpt->clk[EMAC_CLK_MDIO], EMC_CLK_RATE_25MHZ);
+ if (ret)
+ return ret;
+
+ ret = clk_prepare_enable(adpt->clk[EMAC_CLK_MDIO]);
+ if (ret)
+ return ret;
+
+ ret = clk_prepare_enable(adpt->clk[EMAC_CLK_RX]);
+ if (ret)
+ return ret;
+
+ return clk_prepare_enable(adpt->clk[EMAC_CLK_SYS]);
+}
+
+static void emac_clks_phase1_teardown(struct emac_adapter *adpt)
+{
+ clk_disable_unprepare(adpt->clk[EMAC_CLK_AXI]);
+ clk_disable_unprepare(adpt->clk[EMAC_CLK_CFG_AHB]);
+ clk_disable_unprepare(adpt->clk[EMAC_CLK_HIGH_SPEED]);
+}
+
+static void emac_clks_phase2_teardown(struct emac_adapter *adpt)
+{
+ clk_disable_unprepare(adpt->clk[EMAC_CLK_TX]);
+ clk_disable_unprepare(adpt->clk[EMAC_CLK_MDIO]);
+ clk_disable_unprepare(adpt->clk[EMAC_CLK_RX]);
+ clk_disable_unprepare(adpt->clk[EMAC_CLK_SYS]);
+}
+
+/* Get the resources */
+static int emac_probe_resources(struct platform_device *pdev,
+ struct emac_adapter *adpt)
+{
+ struct net_device *netdev = adpt->netdev;
+ struct device_node *node = pdev->dev.of_node;
+ struct resource *res;
+ const void *maddr;
+ int ret = 0;
+ int i;
+
+ if (!node)
+ return -ENODEV;
+
+ /* get id */
+ ret = of_property_read_u32(node, "cell-index", &pdev->id);
+ if (ret)
+ return ret;
+
+ /* get time stamp enable flag */
+ adpt->timestamp_en = of_property_read_bool(node, "qcom,emac-tstamp-en");
+
+ /* get gpios */
+ for (i = 0; adpt->phy.uses_gpios && i < EMAC_GPIO_CNT; i++) {
+ ret = of_get_named_gpio(node, emac_gpio_name[i], 0);
+ if (ret < 0)
+ return ret;
+
+ adpt->gpio[i] = ret;
+ }
+
+ /* get mac address */
+ maddr = of_get_mac_address(node);
+ if (!maddr)
+ return -ENODEV;
+
+ memcpy(adpt->mac_perm_addr, maddr, netdev->addr_len);
+
+ ret = platform_get_irq_byname(pdev, EMAC_MAC_IRQ_RES);
+ if (ret < 0) {
+ netdev_err(adpt->netdev,
+ "error: missing %s resource\n", EMAC_MAC_IRQ_RES);
+ return ret;
+ }
+ adpt->irq.irq = ret;
+
+ ret = emac_clks_get(pdev, adpt);
+ if (ret)
+ return ret;
+
+ /* get register addresses */
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "base");
+ if (!res) {
+ netdev_err(adpt->netdev, "error: missing 'base' resource\n");
+ ret = -ENXIO;
+ goto err_reg_res;
+ }
+
+ adpt->base = devm_ioremap_resource(&pdev->dev, res);
+ if (!adpt->base) {
+ ret = -ENOMEM;
+ goto err_reg_res;
+ }
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "csr");
+ if (!res) {
+ netdev_err(adpt->netdev, "error: missing 'csr' resource\n");
+ ret = -ENXIO;
+ goto err_reg_res;
+ }
+
+ adpt->csr = devm_ioremap_resource(&pdev->dev, res);
+ if (!adpt->csr) {
+ ret = -ENOMEM;
+ goto err_reg_res;
+ }
+
+ netdev->base_addr = (unsigned long)adpt->base;
+ return 0;
+
+err_reg_res:
+ for (i = 0; i < EMAC_CLK_CNT; i++) {
+ if (adpt->clk[i]) {
+ clk_put(adpt->clk[i]);
+ adpt->clk[i] = NULL;
+ }
+ }
+
+ return ret;
+}
+
+/* Release resources */
+static void emac_release_resources(struct emac_adapter *adpt)
+{
+ int i;
+
+ for (i = 0; i < EMAC_CLK_CNT; i++)
+ if (adpt->clk[i]) {
+ clk_put(adpt->clk[i]);
+ adpt->clk[i] = NULL;
+ }
+}
+
+/* Probe function */
+static int emac_probe(struct platform_device *pdev)
+{
+ struct net_device *netdev;
+ struct emac_adapter *adpt;
+ struct emac_phy *phy;
+ int ret = 0;
+ u32 hw_ver;
+ u32 extended_irq_mask = emac_irq_use_extended ? IMR_EXTENDED_MASK :
+ IMR_NORMAL_MASK;
+
+ netdev = alloc_etherdev(sizeof(struct emac_adapter));
+ if (!netdev)
+ return -ENOMEM;
+
+ dev_set_drvdata(&pdev->dev, netdev);
+ SET_NETDEV_DEV(netdev, &pdev->dev);
+
+ adpt = netdev_priv(netdev);
+ adpt->netdev = netdev;
+ phy = &adpt->phy;
+ adpt->msg_enable = netif_msg_init(debug, EMAC_MSG_DEFAULT);
+
+ dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32));
+
+ dma_set_max_seg_size(&pdev->dev, 65536);
+ dma_set_seg_boundary(&pdev->dev, 0xffffffff);
+
+ adpt->irq.mask = RX_PKT_INT0 | extended_irq_mask;
+
+ ret = emac_probe_resources(pdev, adpt);
+ if (ret)
+ goto err_undo_netdev;
+
+ /* initialize clocks */
+ ret = emac_clks_phase1_init(adpt);
+ if (ret)
+ goto err_undo_resources;
+
+ hw_ver = readl_relaxed(adpt->base + EMAC_CORE_HW_VERSION);
+
+ netdev->watchdog_timeo = EMAC_WATCHDOG_TIME;
+ netdev->irq = adpt->irq.irq;
+
+ if (adpt->timestamp_en)
+ adpt->rrd_size = EMAC_TS_RRD_SIZE;
+ else
+ adpt->rrd_size = EMAC_RRD_SIZE;
+
+ adpt->tpd_size = EMAC_TPD_SIZE;
+ adpt->rfd_size = EMAC_RFD_SIZE;
+
+ /* init netdev */
+ netdev->netdev_ops = &emac_netdev_ops;
+
+ /* init adapter */
+ emac_init_adapter(adpt);
+
+ /* init phy */
+ ret = emac_phy_config(pdev, adpt);
+ if (ret)
+ goto err_undo_clk_phase1;
+
+ /* enable clocks */
+ ret = emac_clks_phase2_init(adpt);
+ if (ret)
+ goto err_undo_clk_phase1;
+
+ /* init external phy */
+ ret = emac_phy_external_init(adpt);
+ if (ret)
+ goto err_undo_clk_phase2;
+
+ /* reset mac */
+ emac_mac_reset(adpt);
+
+ /* setup link to put it in a known good starting state */
+ ret = emac_phy_link_setup(adpt, phy->autoneg_advertised, true,
+ !phy->disable_fc_autoneg);
+ if (ret)
+ goto err_undo_clk_phase2;
+
+ /* set mac address */
+ memcpy(adpt->mac_addr, adpt->mac_perm_addr, netdev->addr_len);
+ memcpy(netdev->dev_addr, adpt->mac_addr, netdev->addr_len);
+ emac_mac_addr_clear(adpt, adpt->mac_addr);
+
+ /* set hw features */
+ netdev->features = NETIF_F_SG | NETIF_F_HW_CSUM | NETIF_F_RXCSUM |
+ NETIF_F_TSO | NETIF_F_TSO6 | NETIF_F_HW_VLAN_CTAG_RX |
+ NETIF_F_HW_VLAN_CTAG_TX;
+ netdev->hw_features = netdev->features;
+
+ netdev->vlan_features |= NETIF_F_SG | NETIF_F_HW_CSUM |
+ NETIF_F_TSO | NETIF_F_TSO6;
+
+ setup_timer(&adpt->timers, &emac_timer_thread,
+ (unsigned long)adpt);
+ INIT_WORK(&adpt->work_thread, emac_work_thread);
+
+ /* Initialize queues */
+ emac_mac_rx_tx_ring_init_all(pdev, adpt);
+
+ netif_napi_add(netdev, &adpt->rx_q.napi, emac_napi_rtx, 64);
+
+ spin_lock_init(&adpt->tx_ts_lock);
+ skb_queue_head_init(&adpt->tx_ts_pending_queue);
+ skb_queue_head_init(&adpt->tx_ts_ready_queue);
+ INIT_WORK(&adpt->tx_ts_task, emac_mac_tx_ts_periodic_routine);
+
+ set_bit(EMAC_STATUS_VLANSTRIP_EN, &adpt->status);
+ set_bit(EMAC_STATUS_DOWN, &adpt->status);
+ strlcpy(netdev->name, "eth%d", sizeof(netdev->name));
+
+ ret = register_netdev(netdev);
+ if (ret)
+ goto err_undo_clk_phase2;
+
+ dev_info(&pdev->dev, "%s - version %s\n", emac_drv_description,
+ emac_drv_version);
+ netif_dbg(adpt, probe, adpt->netdev, "EMAC HW ID %d.%d\n", adpt->devid,
+ adpt->revid);
+ netif_dbg(adpt, probe, adpt->netdev, "EMAC HW version %d.%d.%d\n",
+ (hw_ver & MAJOR_BMSK) >> MAJOR_SHFT,
+ (hw_ver & MINOR_BMSK) >> MINOR_SHFT,
+ (hw_ver & STEP_BMSK) >> STEP_SHFT);
+
+ return 0;
+
+err_undo_clk_phase2:
+ emac_clks_phase2_teardown(adpt);
+err_undo_clk_phase1:
+ emac_clks_phase1_teardown(adpt);
+err_undo_resources:
+ emac_release_resources(adpt);
+err_undo_netdev:
+ free_netdev(netdev);
+
+ return ret;
+}
+
+static int emac_remove(struct platform_device *pdev)
+{
+ struct net_device *netdev = dev_get_drvdata(&pdev->dev);
+ struct emac_adapter *adpt = netdev_priv(netdev);
+
+ dev_dbg(&pdev->dev, "removing %s\n", emac_drv_name);
+
+ unregister_netdev(netdev);
+ emac_clks_phase2_teardown(adpt);
+ emac_clks_phase1_teardown(adpt);
+ emac_release_resources(adpt);
+ free_netdev(netdev);
+ dev_set_drvdata(&pdev->dev, NULL);
+
+ return 0;
+}
+
+static const struct dev_pm_ops emac_pm_ops = {
+ SET_SYSTEM_SLEEP_PM_OPS(
+ emac_suspend,
+ emac_resume
+ )
+ SET_RUNTIME_PM_OPS(
+ emac_runtime_suspend,
+ NULL,
+ emac_runtime_idle
+ )
+};
+
+static const struct of_device_id emac_dt_match[] = {
+ {
+ .compatible = "qcom,emac",
+ },
+ {}
+};
+
+static struct platform_driver emac_platform_driver = {
+ .probe = emac_probe,
+ .remove = emac_remove,
+ .driver = {
+ .owner = THIS_MODULE,
+ .name = emac_drv_name,
+ .pm = &emac_pm_ops,
+ .of_match_table = emac_dt_match,
+ },
+};
+
+module_platform_driver(emac_platform_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:qcom-emac");
diff --git a/drivers/net/ethernet/qualcomm/emac/emac.h b/drivers/net/ethernet/qualcomm/emac/emac.h
new file mode 100644
index 0000000..9982617
--- /dev/null
+++ b/drivers/net/ethernet/qualcomm/emac/emac.h
@@ -0,0 +1,388 @@
+/* Copyright (c) 2013-2015, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _EMAC_H_
+#define _EMAC_H_
+
+#include <asm/byteorder.h>
+#include <linux/interrupt.h>
+#include <linux/netdevice.h>
+#include <linux/clk.h>
+#include <linux/platform_device.h>
+#include "emac-mac.h"
+#include "emac-phy.h"
+
+/* EMAC base register offsets */
+#define EMAC_DMA_MAS_CTRL 0x001400
+#define EMAC_IRQ_MOD_TIM_INIT 0x001408
+#define EMAC_BLK_IDLE_STS 0x00140c
+#define EMAC_PHY_LINK_DELAY 0x00141c
+#define EMAC_SYS_ALIV_CTRL 0x001434
+#define EMAC_MAC_IPGIFG_CTRL 0x001484
+#define EMAC_MAC_STA_ADDR0 0x001488
+#define EMAC_MAC_STA_ADDR1 0x00148c
+#define EMAC_HASH_TAB_REG0 0x001490
+#define EMAC_HASH_TAB_REG1 0x001494
+#define EMAC_MAC_HALF_DPLX_CTRL 0x001498
+#define EMAC_MAX_FRAM_LEN_CTRL 0x00149c
+#define EMAC_INT_STATUS 0x001600
+#define EMAC_INT_MASK 0x001604
+#define EMAC_RXMAC_STATC_REG0 0x001700
+#define EMAC_RXMAC_STATC_REG22 0x001758
+#define EMAC_TXMAC_STATC_REG0 0x001760
+#define EMAC_TXMAC_STATC_REG24 0x0017c0
+#define EMAC_CORE_HW_VERSION 0x001974
+#define EMAC_IDT_TABLE0 0x001b00
+#define EMAC_RXMAC_STATC_REG23 0x001bc8
+#define EMAC_RXMAC_STATC_REG24 0x001bcc
+#define EMAC_TXMAC_STATC_REG25 0x001bd0
+#define EMAC_INT1_MASK 0x001bf0
+#define EMAC_INT1_STATUS 0x001bf4
+#define EMAC_INT2_MASK 0x001bf8
+#define EMAC_INT2_STATUS 0x001bfc
+#define EMAC_INT3_MASK 0x001c00
+#define EMAC_INT3_STATUS 0x001c04
+
+/* EMAC_DMA_MAS_CTRL */
+#define DEV_ID_NUM_BMSK 0x7f000000
+#define DEV_ID_NUM_SHFT 24
+#define DEV_REV_NUM_BMSK 0xff0000
+#define DEV_REV_NUM_SHFT 16
+#define INT_RD_CLR_EN 0x4000
+#define IRQ_MODERATOR2_EN 0x800
+#define IRQ_MODERATOR_EN 0x400
+#define LPW_CLK_SEL 0x80
+#define LPW_STATE 0x20
+#define LPW_MODE 0x10
+#define SOFT_RST 0x1
+
+/* EMAC_IRQ_MOD_TIM_INIT */
+#define IRQ_MODERATOR2_INIT_BMSK 0xffff0000
+#define IRQ_MODERATOR2_INIT_SHFT 16
+#define IRQ_MODERATOR_INIT_BMSK 0xffff
+#define IRQ_MODERATOR_INIT_SHFT 0
+
+/* EMAC_INT_STATUS */
+#define DIS_INT BIT(31)
+#define PTP_INT BIT(30)
+#define RFD4_UR_INT BIT(29)
+#define TX_PKT_INT3 BIT(26)
+#define TX_PKT_INT2 BIT(25)
+#define TX_PKT_INT1 BIT(24)
+#define RX_PKT_INT3 BIT(19)
+#define RX_PKT_INT2 BIT(18)
+#define RX_PKT_INT1 BIT(17)
+#define RX_PKT_INT0 BIT(16)
+#define TX_PKT_INT BIT(15)
+#define TXQ_TO_INT BIT(14)
+#define GPHY_WAKEUP_INT BIT(13)
+#define GPHY_LINK_DOWN_INT BIT(12)
+#define GPHY_LINK_UP_INT BIT(11)
+#define DMAW_TO_INT BIT(10)
+#define DMAR_TO_INT BIT(9)
+#define TXF_UR_INT BIT(8)
+#define RFD3_UR_INT BIT(7)
+#define RFD2_UR_INT BIT(6)
+#define RFD1_UR_INT BIT(5)
+#define RFD0_UR_INT BIT(4)
+#define RXF_OF_INT BIT(3)
+#define SW_MAN_INT BIT(2)
+
+/* EMAC_MAILBOX_6 */
+#define RFD2_PROC_IDX_BMSK 0xfff0000
+#define RFD2_PROC_IDX_SHFT 16
+#define RFD2_PROD_IDX_BMSK 0xfff
+#define RFD2_PROD_IDX_SHFT 0
+
+/* EMAC_CORE_HW_VERSION */
+#define MAJOR_BMSK 0xf0000000
+#define MAJOR_SHFT 28
+#define MINOR_BMSK 0xfff0000
+#define MINOR_SHFT 16
+#define STEP_BMSK 0xffff
+#define STEP_SHFT 0
+
+/* EMAC_EMAC_WRAPPER_CSR1 */
+#define TX_INDX_FIFO_SYNC_RST BIT(23)
+#define TX_TS_FIFO_SYNC_RST BIT(22)
+#define RX_TS_FIFO2_SYNC_RST BIT(21)
+#define RX_TS_FIFO1_SYNC_RST BIT(20)
+#define TX_TS_ENABLE BIT(16)
+#define DIS_1588_CLKS BIT(11)
+#define FREQ_MODE BIT(9)
+#define ENABLE_RRD_TIMESTAMP BIT(3)
+
+/* EMAC_EMAC_WRAPPER_CSR2 */
+#define HDRIVE_BMSK 0x3000
+#define HDRIVE_SHFT 12
+#define SLB_EN BIT(9)
+#define PLB_EN BIT(8)
+#define WOL_EN BIT(3)
+#define PHY_RESET BIT(0)
+
+#define EMAC_DEV_ID 0x0040
+
+/* mdio/mdc gpios */
+#define EMAC_GPIO_CNT 2
+
+enum emac_clk_id {
+ EMAC_CLK_AXI,
+ EMAC_CLK_CFG_AHB,
+ EMAC_CLK_HIGH_SPEED,
+ EMAC_CLK_MDIO,
+ EMAC_CLK_TX,
+ EMAC_CLK_RX,
+ EMAC_CLK_SYS,
+ EMAC_CLK_CNT
+};
+
+#define KHz(RATE) ((RATE) * 1000)
+#define MHz(RATE) (KHz(RATE) * 1000)
+
+enum emac_clk_rate {
+ EMC_CLK_RATE_2_5MHZ = KHz(2500),
+ EMC_CLK_RATE_19_2MHZ = KHz(19200),
+ EMC_CLK_RATE_25MHZ = MHz(25),
+ EMC_CLK_RATE_125MHZ = MHz(125),
+};
+
+#define EMAC_LINK_SPEED_UNKNOWN 0x0
+#define EMAC_LINK_SPEED_10_HALF BIT(0)
+#define EMAC_LINK_SPEED_10_FULL BIT(1)
+#define EMAC_LINK_SPEED_100_HALF BIT(2)
+#define EMAC_LINK_SPEED_100_FULL BIT(3)
+#define EMAC_LINK_SPEED_1GB_FULL BIT(5)
+
+#define EMAC_MAX_SETUP_LNK_CYCLE 100
+
+/* Wake On Lan */
+#define EMAC_WOL_PHY 0x00000001 /* PHY Status Change */
+#define EMAC_WOL_MAGIC 0x00000002 /* Magic Packet */
+
+struct emac_stats {
+ /* rx */
+ u64 rx_ok; /* good packets */
+ u64 rx_bcast; /* good broadcast packets */
+ u64 rx_mcast; /* good multicast packets */
+ u64 rx_pause; /* pause packet */
+ u64 rx_ctrl; /* control packets other than pause frame. */
+ u64 rx_fcs_err; /* packets with bad FCS. */
+ u64 rx_len_err; /* packets with length mismatch */
+ u64 rx_byte_cnt; /* good bytes count (without FCS) */
+ u64 rx_runt; /* runt packets */
+ u64 rx_frag; /* fragment count */
+ u64 rx_sz_64; /* packets that are 64 bytes */
+ u64 rx_sz_65_127; /* packets that are 65-127 bytes */
+ u64 rx_sz_128_255; /* packets that are 128-255 bytes */
+ u64 rx_sz_256_511; /* packets that are 256-511 bytes */
+ u64 rx_sz_512_1023; /* packets that are 512-1023 bytes */
+ u64 rx_sz_1024_1518; /* packets that are 1024-1518 bytes */
+ u64 rx_sz_1519_max; /* packets that are 1519-MTU bytes*/
+ u64 rx_sz_ov; /* packets that are >MTU bytes (truncated) */
+ u64 rx_rxf_ov; /* packets dropped due to RX FIFO overflow */
+ u64 rx_align_err; /* alignment errors */
+ u64 rx_bcast_byte_cnt; /* broadcast packets byte count (without FCS) */
+ u64 rx_mcast_byte_cnt; /* multicast packets byte count (without FCS) */
+ u64 rx_err_addr; /* packets dropped due to address filtering */
+ u64 rx_crc_align; /* CRC align errors */
+ u64 rx_jubbers; /* jubbers */
+
+ /* tx */
+ u64 tx_ok; /* good packets */
+ u64 tx_bcast; /* good broadcast packets */
+ u64 tx_mcast; /* good multicast packets */
+ u64 tx_pause; /* pause packets */
+ u64 tx_exc_defer; /* packets with excessive deferral */
+ u64 tx_ctrl; /* control packets other than pause frame */
+ u64 tx_defer; /* packets that are deferred. */
+ u64 tx_byte_cnt; /* good bytes count (without FCS) */
+ u64 tx_sz_64; /* packets that are 64 bytes */
+ u64 tx_sz_65_127; /* packets that are 65-127 bytes */
+ u64 tx_sz_128_255; /* packets that are 128-255 bytes */
+ u64 tx_sz_256_511; /* packets that are 256-511 bytes */
+ u64 tx_sz_512_1023; /* packets that are 512-1023 bytes */
+ u64 tx_sz_1024_1518; /* packets that are 1024-1518 bytes */
+ u64 tx_sz_1519_max; /* packets that are 1519-MTU bytes */
+ u64 tx_1_col; /* packets single prior collision */
+ u64 tx_2_col; /* packets with multiple prior collisions */
+ u64 tx_late_col; /* packets with late collisions */
+ u64 tx_abort_col; /* packets aborted due to excess collisions */
+ u64 tx_underrun; /* packets aborted due to FIFO underrun */
+ u64 tx_rd_eop; /* count of reads beyond EOP */
+ u64 tx_len_err; /* packets with length mismatch */
+ u64 tx_trunc; /* packets truncated due to size >MTU */
+ u64 tx_bcast_byte; /* broadcast packets byte count (without FCS) */
+ u64 tx_mcast_byte; /* multicast packets byte count (without FCS) */
+ u64 tx_col; /* collisions */
+};
+
+enum emac_status_bits {
+ EMAC_STATUS_PROMISC_EN,
+ EMAC_STATUS_VLANSTRIP_EN,
+ EMAC_STATUS_MULTIALL_EN,
+ EMAC_STATUS_LOOPBACK_EN,
+ EMAC_STATUS_TS_RX_EN,
+ EMAC_STATUS_TS_TX_EN,
+ EMAC_STATUS_RESETTING,
+ EMAC_STATUS_DOWN,
+ EMAC_STATUS_WATCH_DOG,
+ EMAC_STATUS_TASK_REINIT_REQ,
+ EMAC_STATUS_TASK_LSC_REQ,
+ EMAC_STATUS_TASK_CHK_SGMII_REQ,
+};
+
+/* RSS hstype Definitions */
+#define EMAC_RSS_HSTYP_IPV4_EN 0x00000001
+#define EMAC_RSS_HSTYP_TCP4_EN 0x00000002
+#define EMAC_RSS_HSTYP_IPV6_EN 0x00000004
+#define EMAC_RSS_HSTYP_TCP6_EN 0x00000008
+#define EMAC_RSS_HSTYP_ALL_EN (\
+ EMAC_RSS_HSTYP_IPV4_EN |\
+ EMAC_RSS_HSTYP_TCP4_EN |\
+ EMAC_RSS_HSTYP_IPV6_EN |\
+ EMAC_RSS_HSTYP_TCP6_EN)
+
+#define EMAC_VLAN_TO_TAG(_vlan, _tag) \
+ (_tag = ((((_vlan) >> 8) & 0xFF) | (((_vlan) & 0xFF) << 8)))
+
+#define EMAC_TAG_TO_VLAN(_tag, _vlan) \
+ (_vlan = ((((_tag) >> 8) & 0xFF) | (((_tag) & 0xFF) << 8)))
+
+#define EMAC_DEF_RX_BUF_SIZE 1536
+#define EMAC_MAX_JUMBO_PKT_SIZE (9 * 1024)
+#define EMAC_MAX_TX_OFFLOAD_THRESH (9 * 1024)
+
+#define EMAC_MAX_ETH_FRAME_SIZE EMAC_MAX_JUMBO_PKT_SIZE
+#define EMAC_MIN_ETH_FRAME_SIZE 68
+
+#define EMAC_DEF_TX_QUEUES 1
+#define EMAC_DEF_RX_QUEUES 1
+
+#define EMAC_MIN_TX_DESCS 128
+#define EMAC_MIN_RX_DESCS 128
+
+#define EMAC_MAX_TX_DESCS 16383
+#define EMAC_MAX_RX_DESCS 2047
+
+#define EMAC_DEF_TX_DESCS 512
+#define EMAC_DEF_RX_DESCS 256
+
+#define EMAC_DEF_RX_IRQ_MOD 250
+#define EMAC_DEF_TX_IRQ_MOD 250
+
+#define EMAC_WATCHDOG_TIME (5 * HZ)
+
+/* by default check link every 4 seconds */
+#define EMAC_TRY_LINK_TIMEOUT (4 * HZ)
+
+/* emac_irq per-device (per-adapter) irq properties.
+ * @idx: index of this irq entry in the adapter irq array.
+ * @irq: irq number.
+ * @mask mask to use over status register.
+ */
+struct emac_irq {
+ int idx;
+ unsigned int irq;
+ u32 mask;
+};
+
+/* emac_irq_config irq properties which are common to all devices of this driver
+ * @name name in configuration (devicetree).
+ * @handler ISR.
+ * @status_reg status register offset.
+ * @mask_reg mask register offset.
+ * @init_mask initial value for mask to use over status register.
+ * @irqflags request_irq() flags.
+ */
+struct emac_irq_config {
+ char *name;
+ irq_handler_t handler;
+
+ u32 status_reg;
+ u32 mask_reg;
+ u32 init_mask;
+
+ unsigned long irqflags;
+};
+
+/* The device's main data structure */
+struct emac_adapter {
+ struct net_device *netdev;
+
+ void __iomem *base;
+ void __iomem *csr;
+
+ struct emac_phy phy;
+ struct emac_stats stats;
+
+ struct emac_irq irq;
+ unsigned int gpio[EMAC_GPIO_CNT];
+ struct clk *clk[EMAC_CLK_CNT];
+
+ /* All Descriptor memory */
+ struct emac_ring_header ring_header;
+ struct emac_tx_queue tx_q;
+ struct emac_rx_queue rx_q;
+ unsigned int tx_desc_cnt;
+ unsigned int rx_desc_cnt;
+ unsigned int rrd_size; /* in quad words */
+ unsigned int rfd_size; /* in quad words */
+ unsigned int tpd_size; /* in quad words */
+
+ unsigned int rxbuf_size;
+
+ u16 devid;
+ u16 revid;
+
+ /* Ring parameter */
+ u8 tpd_burst;
+ u8 rfd_burst;
+ unsigned int dmaw_dly_cnt;
+ unsigned int dmar_dly_cnt;
+ enum emac_dma_req_block dmar_block;
+ enum emac_dma_req_block dmaw_block;
+ enum emac_dma_order dma_order;
+
+ /* MAC parameter */
+ u8 mac_addr[ETH_ALEN];
+ u8 mac_perm_addr[ETH_ALEN];
+ u32 mtu;
+
+ u32 irq_mod;
+ u32 preamble;
+
+ /* Tx time-stamping queue */
+ struct sk_buff_head tx_ts_pending_queue;
+ struct sk_buff_head tx_ts_ready_queue;
+ struct work_struct tx_ts_task;
+ spinlock_t tx_ts_lock; /* Tx timestamp que lock */
+ struct emac_tx_ts_stats tx_ts_stats;
+
+ struct work_struct work_thread;
+ struct timer_list timers;
+ unsigned long link_chk_timeout;
+
+ bool timestamp_en;
+ u16 msg_enable;
+ unsigned long status;
+};
+
+void emac_reinit_locked(struct emac_adapter *adpt);
+void emac_work_thread_reschedule(struct emac_adapter *adpt);
+void emac_lsc_schedule_check(struct emac_adapter *adpt);
+void emac_rx_mode_set(struct net_device *netdev);
+void emac_reg_update32(void __iomem *addr, u32 mask, u32 val);
+irqreturn_t emac_isr(int irq, void *data);
+
+extern const char * const emac_gpio_name[];
+
+#endif /* _EMAC_H_ */
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 19+ messages in thread
* Re: [PATCH V3] net: emac: emac gigabit ethernet controller driver
2015-12-30 1:48 [PATCH V3] net: emac: emac gigabit ethernet controller driver Gilad Avidov
@ 2015-12-30 2:31 ` kbuild test robot
[not found] ` <1451440135-25771-1-git-send-email-gavidov-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
` (2 subsequent siblings)
3 siblings, 0 replies; 19+ messages in thread
From: kbuild test robot @ 2015-12-30 2:31 UTC (permalink / raw)
Cc: kbuild-all, netdev, linux-kernel, devicetree, linux-arm-msm,
sdharia, shankerd, timur, gregkh, vikrams, cov, Gilad Avidov
[-- Attachment #1: Type: text/plain, Size: 1831 bytes --]
Hi Gilad,
[auto build test WARNING on net/master]
[also build test WARNING on v4.4-rc7 next-20151223]
[if your patch is applied to the wrong git tree, please drop us a note to help improving the system]
url: https://github.com/0day-ci/linux/commits/Gilad-Avidov/net-emac-emac-gigabit-ethernet-controller-driver/20151230-095104
config: x86_64-allmodconfig (attached as .config)
reproduce:
# save the attached .config to linux build tree
make ARCH=x86_64
All warnings (new ones prefixed by >>):
drivers/net/ethernet/qualcomm/emac/emac-mac.c: In function 'emac_mac_up':
>> drivers/net/ethernet/qualcomm/emac/emac-mac.c:1090:9: warning: large integer implicitly truncated to unsigned type [-Woverflow]
writel(~DIS_INT, adpt->base + EMAC_INT_STATUS);
^
vim +1090 drivers/net/ethernet/qualcomm/emac/emac-mac.c
1074 }
1075 }
1076
1077 ret = request_irq(irq->irq, emac_isr, 0, EMAC_MAC_IRQ_RES, irq);
1078 if (ret) {
1079 netdev_err(adpt->netdev,
1080 "error:%d on request_irq(%d:%s flags:0)\n", ret,
1081 irq->irq, EMAC_MAC_IRQ_RES);
1082 goto err_request_irq;
1083 }
1084
1085 emac_mac_rx_descs_refill(adpt, &adpt->rx_q);
1086
1087 napi_enable(&adpt->rx_q.napi);
1088
1089 /* enable mac irq */
> 1090 writel(~DIS_INT, adpt->base + EMAC_INT_STATUS);
1091 writel(adpt->irq.mask, adpt->base + EMAC_INT_MASK);
1092
1093 netif_start_queue(netdev);
1094 clear_bit(EMAC_STATUS_DOWN, &adpt->status);
1095
1096 /* check link status */
1097 set_bit(EMAC_STATUS_TASK_LSC_REQ, &adpt->status);
1098 adpt->link_chk_timeout = jiffies + EMAC_TRY_LINK_TIMEOUT;
---
0-DAY kernel test infrastructure Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all Intel Corporation
[-- Attachment #2: .config.gz --]
[-- Type: application/octet-stream, Size: 51057 bytes --]
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH V3] net: emac: emac gigabit ethernet controller driver
[not found] ` <1451440135-25771-1-git-send-email-gavidov-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
@ 2015-12-30 4:26 ` kbuild test robot
0 siblings, 0 replies; 19+ messages in thread
From: kbuild test robot @ 2015-12-30 4:26 UTC (permalink / raw)
Cc: kbuild-all-JC7UmRfGjtg, netdev-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-msm-u79uwXL29TY76Z2rM5mHXA,
sdharia-sgV2jX0FEOL9JmXXK+q4OQ, shankerd-sgV2jX0FEOL9JmXXK+q4OQ,
timur-sgV2jX0FEOL9JmXXK+q4OQ,
gregkh-hQyY1W1yCW8ekmWlsbkhG0B+6BGkLq7r,
vikrams-sgV2jX0FEOL9JmXXK+q4OQ, cov-sgV2jX0FEOL9JmXXK+q4OQ,
Gilad Avidov
[-- Attachment #1: Type: text/plain, Size: 2631 bytes --]
Hi Gilad,
[auto build test WARNING on net/master]
[also build test WARNING on v4.4-rc7 next-20151223]
[if your patch is applied to the wrong git tree, please drop us a note to help improving the system]
url: https://github.com/0day-ci/linux/commits/Gilad-Avidov/net-emac-emac-gigabit-ethernet-controller-driver/20151230-095104
config: ia64-allyesconfig (attached as .config)
reproduce:
wget https://git.kernel.org/cgit/linux/kernel/git/wfg/lkp-tests.git/plain/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# save the attached .config to linux build tree
make.cross ARCH=ia64
All warnings (new ones prefixed by >>):
In file included from arch/ia64/include/asm/smp.h:20:0,
from include/linux/smp.h:59,
from include/linux/topology.h:33,
from include/linux/gfp.h:8,
from include/linux/slab.h:14,
from include/linux/textsearch.h:8,
from include/linux/skbuff.h:30,
from include/linux/tcp.h:21,
from drivers/net/ethernet/qualcomm/emac/emac-mac.c:16:
drivers/net/ethernet/qualcomm/emac/emac-mac.c: In function 'emac_mac_up':
arch/ia64/include/asm/io.h:394:30: warning: large integer implicitly truncated to unsigned type [-Woverflow]
#define writel(v,a) __writel((v), (a))
^
>> drivers/net/ethernet/qualcomm/emac/emac-mac.c:1090:2: note: in expansion of macro 'writel'
writel(~DIS_INT, adpt->base + EMAC_INT_STATUS);
^
vim +/writel +1090 drivers/net/ethernet/qualcomm/emac/emac-mac.c
1074 }
1075 }
1076
1077 ret = request_irq(irq->irq, emac_isr, 0, EMAC_MAC_IRQ_RES, irq);
1078 if (ret) {
1079 netdev_err(adpt->netdev,
1080 "error:%d on request_irq(%d:%s flags:0)\n", ret,
1081 irq->irq, EMAC_MAC_IRQ_RES);
1082 goto err_request_irq;
1083 }
1084
1085 emac_mac_rx_descs_refill(adpt, &adpt->rx_q);
1086
1087 napi_enable(&adpt->rx_q.napi);
1088
1089 /* enable mac irq */
> 1090 writel(~DIS_INT, adpt->base + EMAC_INT_STATUS);
1091 writel(adpt->irq.mask, adpt->base + EMAC_INT_MASK);
1092
1093 netif_start_queue(netdev);
1094 clear_bit(EMAC_STATUS_DOWN, &adpt->status);
1095
1096 /* check link status */
1097 set_bit(EMAC_STATUS_TASK_LSC_REQ, &adpt->status);
1098 adpt->link_chk_timeout = jiffies + EMAC_TRY_LINK_TIMEOUT;
---
0-DAY kernel test infrastructure Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all Intel Corporation
[-- Attachment #2: .config.gz --]
[-- Type: application/octet-stream, Size: 44483 bytes --]
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH V3] net: emac: emac gigabit ethernet controller driver
2015-12-30 1:48 [PATCH V3] net: emac: emac gigabit ethernet controller driver Gilad Avidov
2015-12-30 2:31 ` kbuild test robot
[not found] ` <1451440135-25771-1-git-send-email-gavidov-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
@ 2015-12-31 23:10 ` Rob Herring
2016-01-29 18:22 ` Timur Tabi
2016-01-06 0:21 ` Timur Tabi
3 siblings, 1 reply; 19+ messages in thread
From: Rob Herring @ 2015-12-31 23:10 UTC (permalink / raw)
To: Gilad Avidov
Cc: netdev, linux-kernel, devicetree, linux-arm-msm, sdharia,
shankerd, timur, gregkh, vikrams, cov
On Tue, Dec 29, 2015 at 06:48:55PM -0700, Gilad Avidov wrote:
> Add supports for ethernet controller HW on Qualcomm Technologies, Inc. SoC.
> This driver supports the following features:
> 1) Checksum offload.
> 2) Runtime power management support.
> 3) Interrupt coalescing support.
> 4) SGMII phy.
> 5) SGMII direct connection without external phy.
>
> Based on a driver by Niranjana Vishwanathapura
> <nvishwan@codeaurora.org>.
[...]
> diff --git a/Documentation/devicetree/bindings/net/qcom-emac.txt b/Documentation/devicetree/bindings/net/qcom-emac.txt
> new file mode 100644
> index 0000000..8d58a40
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/qcom-emac.txt
> @@ -0,0 +1,68 @@
> +Qualcomm EMAC Gigabit Ethernet Controller
> +
> +Required properties:
> +- cell-index : EMAC controller instance number.
> +- compatible : Should be "qcom,emac".
This should be more specific with the SOC name.
> +- reg : Offset and length of the register regions for the device
> +- reg-names : Register region names referenced in 'reg' above.
> + Required register resource entries are:
> + "base" : EMAC controller base register block.
> + "csr" : EMAC wrapper register block.
> + Optional register resource entries are:
> + "ptp" : EMAC PTP (1588) register block.
> + Required if 'qcom,emac-tstamp-en' is present.
> + "sgmii" : EMAC SGMII PHY register block.
> +- interrupts : Interrupt numbers used by this controller
> +- interrupt-names : Interrupt resource names referenced in 'interrupts' above.
> + Required interrupt resource entries are:
> + "emac_core0" : EMAC core0 interrupt.
> + "sgmii_irq" : EMAC SGMII interrupt.
> +- qcom,emac-gpio-mdc : GPIO pin number of the MDC line of MDIO bus.
> +- qcom,emac-gpio-mdio : GPIO pin number of the MDIO line of MDIO bus.
Use the standard binding for GPIO controlled MDIO bus.
> +- phy-addr : Specifies phy address on MDIO bus.
> + Required if the optional property "qcom,no-external-phy"
> + is not specified.
Don't you think you will need to know the specific phy device or other
properties of the phy?
> +
> +Optional properties:
> +- qcom,emac-tstamp-en : Enables the PTP (1588) timestamping feature.
> + Include this only if PTP (1588) timestamping
> + feature is needed. If included, "ptp" register
> + base should be specified.
Isn't this a user enabled feature if the h/w supports it?
> +- mac-address : The 6-byte MAC address. If present, it is the
> + default MAC address.
> +- qcom,no-external-phy : Indicates there is no external PHY connected to
> + EMAC. Include this only if the EMAC is directly
> + connected to the peer end without EPHY.
> +- qcom,emac-ptp-grandmaster : Enable the PTP (1588) grandmaster mode.
> + Include this only if PTP (1588) is configured as
> + grandmaster.
> +- qcom,emac-ptp-frac-ns-adj : The vector table to adjust the fractional ns per
> + RTC clock cycle.
> + Include this only if there is accuracy loss of
> + fractional ns per RTC clock cycle. For individual
> + table entry, the first field indicates the RTC
> + reference clock rate. The second field indicates
> + the number of adjustment in 2 ^ -26 ns.
> +Example:
> + emac0: qcom,emac@feb20000 {
> + cell-index = <0>;
> + compatible = "qcom,emac";
> + reg-names = "base", "csr", "ptp", "sgmii";
> + reg = <0xfeb20000 0x10000>,
> + <0xfeb36000 0x1000>,
> + <0xfeb3c000 0x4000>,
> + <0xfeb38000 0x400>;
> + #address-cells = <0>;
> + interrupt-parent = <&emac0>;
> + #interrupt-cells = <1>;
> + interrupts = <0 1>;
> + interrupt-map-mask = <0xffffffff>;
> + interrupt-map = <0 &intc 0 76 0
> + 1 &intc 0 80 0>;
> + interrupt-names = "emac_core0", "sgmii_irq";
> + qcom,emac-gpio-mdc = <&qcomgpio 123 0>;
> + qcom,emac-gpio-mdio = <&qcomgpio 124 0>;
> + qcom,emac-tstamp-en;
> + qcom,emac-ptp-frac-ns-adj = <125000000 1>;
> + phy-addr = <0>;
> + };
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH V3] net: emac: emac gigabit ethernet controller driver
2015-12-30 1:48 [PATCH V3] net: emac: emac gigabit ethernet controller driver Gilad Avidov
` (2 preceding siblings ...)
2015-12-31 23:10 ` Rob Herring
@ 2016-01-06 0:21 ` Timur Tabi
3 siblings, 0 replies; 19+ messages in thread
From: Timur Tabi @ 2016-01-06 0:21 UTC (permalink / raw)
To: Gilad Avidov, netdev, linux-kernel, devicetree, linux-arm-msm
Cc: sdharia, shankerd, gregkh, vikrams, cov
Gilad Avidov wrote:
> diff --git a/drivers/net/ethernet/qualcomm/emac/emac-mac.c b/drivers/net/ethernet/qualcomm/emac/emac-mac.c
> new file mode 100644
> index 0000000..36a7746
> --- /dev/null
> +++ b/drivers/net/ethernet/qualcomm/emac/emac-mac.c
> @@ -0,0 +1,1808 @@
> +/* Copyright (c) 2013-2015, The Linux Foundation. All rights reserved.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 and
> + * only version 2 as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +/* Qualcomm Technologies, Inc. EMAC Ethernet Controller MAC layer support
> + */
> +
> +#include <linux/tcp.h>
> +#include <linux/ip.h>
> +#include <linux/ipv6.h>
> +#include <linux/crc32.h>
> +#include <linux/if_vlan.h>
> +#include <linux/jiffies.h>
> +#include <linux/phy.h>
> +#include <linux/of.h>
> +#include <linux/gpio.h>
> +#include <linux/pm_runtime.h>
> +#include "emac.h"
> +#include "emac-sgmii.h"
You also need
#include <net/ip6_checksum.h>
otherwise you get this:
CC drivers/net/ethernet/qualcomm/emac/emac-mac.o
drivers/net/ethernet/qualcomm/emac/emac-mac.c: In function 'emac_tso_csum':
drivers/net/ethernet/qualcomm/emac/emac-mac.c:2045:4: error: implicit
declaration of function 'csum_ipv6_magic'
[-Werror=implicit-function-declaration]
tcp_hdr(skb)->check = ~csum_ipv6_magic(
^
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH V3] net: emac: emac gigabit ethernet controller driver
2015-12-31 23:10 ` Rob Herring
@ 2016-01-29 18:22 ` Timur Tabi
[not found] ` <56ABADEA.40801-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
0 siblings, 1 reply; 19+ messages in thread
From: Timur Tabi @ 2016-01-29 18:22 UTC (permalink / raw)
To: Rob Herring, Gilad Avidov
Cc: netdev, linux-kernel, devicetree, linux-arm-msm, sdharia,
shankerd, gregkh, vikrams, cov
Gilad is no longer working for Qualcomm, so I'm taking over (as best as
I can) this driver. Let's just say it's going to be a learning experience.
Rob Herring wrote:
>> diff --git a/Documentation/devicetree/bindings/net/qcom-emac.txt b/Documentation/devicetree/bindings/net/qcom-emac.txt
>> new file mode 100644
>> index 0000000..8d58a40
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/net/qcom-emac.txt
>> @@ -0,0 +1,68 @@
>> +Qualcomm EMAC Gigabit Ethernet Controller
>> +
>> +Required properties:
>> +- cell-index : EMAC controller instance number.
>> +- compatible : Should be "qcom,emac".
>
> This should be more specific with the SOC name.
The emac is present on a lot of Qualcomm SOCs, and there are only a few
variations of it. It's not really SOC-specific, and the hardware
version can be queried by the driver.
What did you have in mind? I don't know even have a list of which SOCs
has an emac, especially since it's mostly on MSM parts, and I work on
the server SOC.
>> +- reg : Offset and length of the register regions for the device
>> +- reg-names : Register region names referenced in 'reg' above.
>> + Required register resource entries are:
>> + "base" : EMAC controller base register block.
>> + "csr" : EMAC wrapper register block.
>> + Optional register resource entries are:
>> + "ptp" : EMAC PTP (1588) register block.
>> + Required if 'qcom,emac-tstamp-en' is present.
>> + "sgmii" : EMAC SGMII PHY register block.
>> +- interrupts : Interrupt numbers used by this controller
>> +- interrupt-names : Interrupt resource names referenced in 'interrupts' above.
>> + Required interrupt resource entries are:
>> + "emac_core0" : EMAC core0 interrupt.
>> + "sgmii_irq" : EMAC SGMII interrupt.
>> +- qcom,emac-gpio-mdc : GPIO pin number of the MDC line of MDIO bus.
>> +- qcom,emac-gpio-mdio : GPIO pin number of the MDIO line of MDIO bus.
>
> Use the standard binding for GPIO controlled MDIO bus.
I'm not familiar with that one. Are you talking about
bindings/net/mdio-gpio.txt?
>> +- phy-addr : Specifies phy address on MDIO bus.
>> + Required if the optional property "qcom,no-external-phy"
>> + is not specified.
>
> Don't you think you will need to know the specific phy device or other
> properties of the phy?
That, I can't answer. Aren't all MDIO devices basically the same? It's
been a while since I've worked on them.
>> +Optional properties:
>> +- qcom,emac-tstamp-en : Enables the PTP (1588) timestamping feature.
>> + Include this only if PTP (1588) timestamping
>> + feature is needed. If included, "ptp" register
>> + base should be specified.
>
> Isn't this a user enabled feature if the h/w supports it?
Is there a sysfs entry for that? We were planning on having a similar
ACPI property.
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH V3] net: emac: emac gigabit ethernet controller driver
[not found] ` <56ABADEA.40801-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
@ 2016-01-29 20:10 ` Rob Herring
2016-01-29 20:38 ` Timur Tabi
2016-04-07 19:28 ` Timur Tabi
0 siblings, 2 replies; 19+ messages in thread
From: Rob Herring @ 2016-01-29 20:10 UTC (permalink / raw)
To: Timur Tabi
Cc: Gilad Avidov, netdev, linux-kernel-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA, linux-arm-msm, Sagar Dharia,
shankerd-sgV2jX0FEOL9JmXXK+q4OQ, Greg Kroah-Hartman,
vikrams-sgV2jX0FEOL9JmXXK+q4OQ, Christopher Covington
On Fri, Jan 29, 2016 at 12:22 PM, Timur Tabi <timur-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org> wrote:
> Gilad is no longer working for Qualcomm, so I'm taking over (as best as I
> can) this driver. Let's just say it's going to be a learning experience.
Lucky you.
> Rob Herring wrote:
>>>
>>> diff --git a/Documentation/devicetree/bindings/net/qcom-emac.txt
>>> b/Documentation/devicetree/bindings/net/qcom-emac.txt
>>> new file mode 100644
>>> index 0000000..8d58a40
>>> --- /dev/null
>>> +++ b/Documentation/devicetree/bindings/net/qcom-emac.txt
>>> @@ -0,0 +1,68 @@
>>> +Qualcomm EMAC Gigabit Ethernet Controller
>>> +
>>> +Required properties:
>>> +- cell-index : EMAC controller instance number.
>>> +- compatible : Should be "qcom,emac".
>>
>>
>> This should be more specific with the SOC name.
>
>
> The emac is present on a lot of Qualcomm SOCs, and there are only a few
> variations of it. It's not really SOC-specific, and the hardware version
> can be queried by the driver.
Can the integration bugs be queried, too?
Come on, you know how compatible strings work.
> What did you have in mind? I don't know even have a list of which SOCs has
> an emac, especially since it's mostly on MSM parts, and I work on the server
> SOC.
You only need the one you care about. Figure out the part number
already. Or find the closest MSM part.
>>> +- reg : Offset and length of the register regions for the device
>>> +- reg-names : Register region names referenced in 'reg' above.
>>> + Required register resource entries are:
>>> + "base" : EMAC controller base register block.
>>> + "csr" : EMAC wrapper register block.
>>> + Optional register resource entries are:
>>> + "ptp" : EMAC PTP (1588) register block.
>>> + Required if 'qcom,emac-tstamp-en' is present.
>>> + "sgmii" : EMAC SGMII PHY register block.
>>> +- interrupts : Interrupt numbers used by this controller
>>> +- interrupt-names : Interrupt resource names referenced in 'interrupts'
>>> above.
>>> + Required interrupt resource entries are:
>>> + "emac_core0" : EMAC core0 interrupt.
>>> + "sgmii_irq" : EMAC SGMII interrupt.
>>> +- qcom,emac-gpio-mdc : GPIO pin number of the MDC line of MDIO bus.
>>> +- qcom,emac-gpio-mdio : GPIO pin number of the MDIO line of MDIO bus.
>>
>>
>> Use the standard binding for GPIO controlled MDIO bus.
>
>
> I'm not familiar with that one. Are you talking about
> bindings/net/mdio-gpio.txt?
Yes.
>>> +- phy-addr : Specifies phy address on MDIO bus.
>>> + Required if the optional property
>>> "qcom,no-external-phy"
>>> + is not specified.
>>
>>
>> Don't you think you will need to know the specific phy device or other
>> properties of the phy?
>
>
> That, I can't answer. Aren't all MDIO devices basically the same? It's
> been a while since I've worked on them.
No. There was some discussion just this week about needing to require
phy devices to have compatible strings.
>>> +Optional properties:
>>> +- qcom,emac-tstamp-en : Enables the PTP (1588) timestamping
>>> feature.
>>> + Include this only if PTP (1588)
>>> timestamping
>>> + feature is needed. If included, "ptp"
>>> register
>>> + base should be specified.
>>
>>
>> Isn't this a user enabled feature if the h/w supports it?
>
>
> Is there a sysfs entry for that? We were planning on having a similar ACPI
> property.
It would be in ethtool I think.
Rob
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH V3] net: emac: emac gigabit ethernet controller driver
2016-01-29 20:10 ` Rob Herring
@ 2016-01-29 20:38 ` Timur Tabi
2016-01-30 21:58 ` Rob Herring
2016-04-07 19:28 ` Timur Tabi
1 sibling, 1 reply; 19+ messages in thread
From: Timur Tabi @ 2016-01-29 20:38 UTC (permalink / raw)
To: Rob Herring
Cc: Gilad Avidov, netdev, linux-kernel, devicetree, linux-arm-msm,
Sagar Dharia, shankerd, Greg Kroah-Hartman, vikrams,
Christopher Covington
Rob Herring wrote:
>> The emac is present on a lot of Qualcomm SOCs, and there are only a few
>> variations of it. It's not really SOC-specific, and the hardware version
>> can be queried by the driver.
>
> Can the integration bugs be queried, too?
>
> Come on, you know how compatible strings work.
Fine. I'll figure something out.
>> What did you have in mind? I don't know even have a list of which SOCs has
>> an emac, especially since it's mostly on MSM parts, and I work on the server
>> SOC.
>
> You only need the one you care about. Figure out the part number
> already. Or find the closest MSM part.
Ironically, the only SOC I actually care about is not supported by this
driver yet.
>>>> +- qcom,emac-gpio-mdc : GPIO pin number of the MDC line of MDIO bus.
>>>> +- qcom,emac-gpio-mdio : GPIO pin number of the MDIO line of MDIO bus.
>>>
>>>
>>> Use the standard binding for GPIO controlled MDIO bus.
>>
>> I'm not familiar with that one. Are you talking about
>> bindings/net/mdio-gpio.txt?
>
> Yes.
Thanks.
>> That, I can't answer. Aren't all MDIO devices basically the same? It's
>> been a while since I've worked on them.
>
> No. There was some discussion just this week about needing to require
> phy devices to have compatible strings.
Ok, I'll check it out.
>>> Isn't this a user enabled feature if the h/w supports it?
>>
>>
>> Is there a sysfs entry for that? We were planning on having a similar ACPI
>> property.
>
> It would be in ethtool I think.
Ah, this driver does not support ethtool yet.
However, based on a cursory look of ethtool, it appears that there's
only an option to query the current timestamp, but not actually
enable/disable the feature. The e1000e driver, for example, just forces
the feature by default for various chips. Is there any reason why we
shouldn't enable it if the hardware supports it?
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH V3] net: emac: emac gigabit ethernet controller driver
2016-01-29 20:38 ` Timur Tabi
@ 2016-01-30 21:58 ` Rob Herring
0 siblings, 0 replies; 19+ messages in thread
From: Rob Herring @ 2016-01-30 21:58 UTC (permalink / raw)
To: Timur Tabi
Cc: Gilad Avidov, netdev, linux-kernel, devicetree, linux-arm-msm,
Sagar Dharia, shankerd, Greg Kroah-Hartman, vikrams,
Christopher Covington
On Fri, Jan 29, 2016 at 2:38 PM, Timur Tabi <timur@codeaurora.org> wrote:
> Rob Herring wrote:
[...]
>>>> Isn't this a user enabled feature if the h/w supports it?
>>>
>>>
>>>
>>> Is there a sysfs entry for that? We were planning on having a similar
>>> ACPI
>>> property.
>>
>>
>> It would be in ethtool I think.
>
>
> Ah, this driver does not support ethtool yet.
>
> However, based on a cursory look of ethtool, it appears that there's only an
> option to query the current timestamp, but not actually enable/disable the
> feature. The e1000e driver, for example, just forces the feature by default
> for various chips. Is there any reason why we shouldn't enable it if the
> hardware supports it?
Probably not. You simply ignore the timestamp if you don't care. So
then why do you want a DT property?
Rob
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH V3] net: emac: emac gigabit ethernet controller driver
2016-01-29 20:10 ` Rob Herring
2016-01-29 20:38 ` Timur Tabi
@ 2016-04-07 19:28 ` Timur Tabi
[not found] ` <5706B4EF.2050600-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
1 sibling, 1 reply; 19+ messages in thread
From: Timur Tabi @ 2016-04-07 19:28 UTC (permalink / raw)
To: Rob Herring
Cc: Gilad Avidov, netdev, linux-kernel, devicetree, linux-arm-msm,
Sagar Dharia, shankerd, Greg Kroah-Hartman, vikrams,
Christopher Covington
Rob Herring wrote:
>>>> >>>+- reg : Offset and length of the register regions for the device
>>>> >>>+- reg-names : Register region names referenced in 'reg' above.
>>>> >>>+ Required register resource entries are:
>>>> >>>+ "base" : EMAC controller base register block.
>>>> >>>+ "csr" : EMAC wrapper register block.
>>>> >>>+ Optional register resource entries are:
>>>> >>>+ "ptp" : EMAC PTP (1588) register block.
>>>> >>>+ Required if 'qcom,emac-tstamp-en' is present.
>>>> >>>+ "sgmii" : EMAC SGMII PHY register block.
>>>> >>>+- interrupts : Interrupt numbers used by this controller
>>>> >>>+- interrupt-names : Interrupt resource names referenced in 'interrupts'
>>>> >>>above.
>>>> >>>+ Required interrupt resource entries are:
>>>> >>>+ "emac_core0" : EMAC core0 interrupt.
>>>> >>>+ "sgmii_irq" : EMAC SGMII interrupt.
>>>> >>>+- qcom,emac-gpio-mdc : GPIO pin number of the MDC line of MDIO bus.
>>>> >>>+- qcom,emac-gpio-mdio : GPIO pin number of the MDIO line of MDIO bus.
>>> >>
>>> >>
>>> >>Use the standard binding for GPIO controlled MDIO bus.
>> >
>> >
>> >I'm not familiar with that one. Are you talking about
>> >bindings/net/mdio-gpio.txt?
> Yes.
>
>
>>>> >>>+- phy-addr : Specifies phy address on MDIO bus.
>>>> >>>+ Required if the optional property
>>>> >>>"qcom,no-external-phy"
>>>> >>>+ is not specified.
>>> >>
>>> >>
>>> >>Don't you think you will need to know the specific phy device or other
>>> >>properties of the phy?
>> >
>> >
>> >That, I can't answer. Aren't all MDIO devices basically the same? It's
>> >been a while since I've worked on them.
> No. There was some discussion just this week about needing to require
> phy devices to have compatible strings.
I'm back to working on this driver, and I need some more help with how
to handle the phy. mdio-gpio.txt doesn't really tell me much. I'm
actually working on an ACPI system and not DT. I don't want to strip
out the DT code, but I can't really test it. I want to keep changes to
Gilad's patch to a minimum.
Part of the problem with the Emac (and Gilad tried to explain this) is
that it has an internal phy. Technically, you can connect this internal
phy directly to another internal phy on another SOC, and use this as an
SOC interconnect. However, I don't know of anyone actually doing that.
Instead, most systems have the internal phy connect to an external phy.
This connection is how the Emac receives packets from the external phy.
So I don't understand how I'm supposed to use the binding in
mdio-gpio.txt. For one thing, there is no such binding on ACPI systems.
On my ACPI system, firmware has set up the GPIOs. The driver never
actually makes any gpio_xxx calls. At this point, I'm tempted to just
remove all the GPIO stuff from Gilad's patch, if I can't help enough
help to figure out how to modify the driver the way you think I should.
--
Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora
Forum, a Linux Foundation collaborative project.
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH V3] net: emac: emac gigabit ethernet controller driver
[not found] ` <5706B4EF.2050600-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
@ 2016-04-07 20:10 ` Andrew Lunn
[not found] ` <20160407201009.GA16136-g2DYL2Zd6BY@public.gmane.org>
0 siblings, 1 reply; 19+ messages in thread
From: Andrew Lunn @ 2016-04-07 20:10 UTC (permalink / raw)
To: Timur Tabi
Cc: Rob Herring, Gilad Avidov, netdev,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA, linux-arm-msm, Sagar Dharia,
shankerd-sgV2jX0FEOL9JmXXK+q4OQ, Greg Kroah-Hartman,
vikrams-sgV2jX0FEOL9JmXXK+q4OQ, Christopher Covington
> I'm back to working on this driver, and I need some more help with
> how to handle the phy. mdio-gpio.txt doesn't really tell me much.
> I'm actually working on an ACPI system and not DT.
I can help you with DT, but not ACPI.
The MDIO bus can be a separate Linux device. Since you have GPIO lines
for the MDIO bus, it makes sense for this to be a mdio-gpio device. So
in DT, you would have:
mdio0: mdio {
compatible = "virtual,mdio-gpio";
#address-cells = <1>;
#size-cells = <0>;
gpios = <&qcomgpio 123 0
&qcomgpio 124 0>;
phy0: ethernet-phy@8 {
reg = <9>;
};
};
Here i've assumed the PHY is using address 8 on the bus. Change as
needed.
In your MAC DT node, you then have phy-handle pointing to this phy:
emac0: qcom,emac@feb20000 {
cell-index = <0>;
compatible = "qcom,emac";
reg-names = "base", "csr", "ptp", "sgmii";
reg = <0xfeb20000 0x10000>,
<0xfeb36000 0x1000>,
<0xfeb3c000 0x4000>,
<0xfeb38000 0x400>;
#address-cells = <0>;
interrupt-parent = <&emac0>;
#interrupt-cells = <1>;
interrupts = <0 1>;
interrupt-map-mask = <0xffffffff>;
interrupt-map = <0 &intc 0 76 0
1 &intc 0 80 0>;
interrupt-names = "emac_core0", "sgmii_irq";
qcom,emac-tstamp-en;
qcom,emac-ptp-frac-ns-adj = <125000000 1>;
phy-handle = <&phy0>
}
In the driver, you need to connect the PHY to the MAC. You do this
using something like:
if (dev->of_node) {
phy_np = of_parse_phandle(dev->of_node, "phy-handle", 0);
if (!phy_np) {
netdev_dbg(ndev, "No phy-handle found in DT\n");
return -ENODEV;
}
phy_dev = of_phy_connect(ndev, phy_np, &xxxx_enet_adjust_link,
0, pdata->phy_mode);
if (!phy_dev) {
netdev_err(ndev, "Could not connect to PHY\n");
return -ENODEV;
}
Do you have an ACPI table describing this hardware? What does it look
like?
Andrew
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH V3] net: emac: emac gigabit ethernet controller driver
[not found] ` <20160407201009.GA16136-g2DYL2Zd6BY@public.gmane.org>
@ 2016-04-07 21:43 ` Timur Tabi
2016-04-08 0:53 ` Andrew Lunn
0 siblings, 1 reply; 19+ messages in thread
From: Timur Tabi @ 2016-04-07 21:43 UTC (permalink / raw)
To: Andrew Lunn
Cc: Rob Herring, Gilad Avidov, netdev,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA, linux-arm-msm, Sagar Dharia,
shankerd-sgV2jX0FEOL9JmXXK+q4OQ, Greg Kroah-Hartman,
vikrams-sgV2jX0FEOL9JmXXK+q4OQ, Christopher Covington
Andrew Lunn wrote:
>> I'm back to working on this driver, and I need some more help with
>> how to handle the phy. mdio-gpio.txt doesn't really tell me much.
>> I'm actually working on an ACPI system and not DT.
>
> I can help you with DT, but not ACPI.
>
> The MDIO bus can be a separate Linux device. Since you have GPIO lines
> for the MDIO bus, it makes sense for this to be a mdio-gpio device. So
> in DT, you would have:
>
> mdio0: mdio {
> compatible = "virtual,mdio-gpio";
> #address-cells = <1>;
> #size-cells = <0>;
> gpios = <&qcomgpio 123 0
> &qcomgpio 124 0>;
>
> phy0: ethernet-phy@8 {
> reg = <9>;
> };
> };
>
> Here i've assumed the PHY is using address 8 on the bus. Change as
> needed.
>
> In your MAC DT node, you then have phy-handle pointing to this phy:
>
> emac0: qcom,emac@feb20000 {
> cell-index = <0>;
> compatible = "qcom,emac";
> reg-names = "base", "csr", "ptp", "sgmii";
> reg = <0xfeb20000 0x10000>,
> <0xfeb36000 0x1000>,
> <0xfeb3c000 0x4000>,
> <0xfeb38000 0x400>;
> #address-cells = <0>;
> interrupt-parent = <&emac0>;
> #interrupt-cells = <1>;
> interrupts = <0 1>;
> interrupt-map-mask = <0xffffffff>;
> interrupt-map = <0 &intc 0 76 0
> 1 &intc 0 80 0>;
> interrupt-names = "emac_core0", "sgmii_irq";
> qcom,emac-tstamp-en;
> qcom,emac-ptp-frac-ns-adj = <125000000 1>;
>
> phy-handle = <&phy0>
> }
>
> In the driver, you need to connect the PHY to the MAC. You do this
> using something like:
>
> if (dev->of_node) {
> phy_np = of_parse_phandle(dev->of_node, "phy-handle", 0);
> if (!phy_np) {
> netdev_dbg(ndev, "No phy-handle found in DT\n");
> return -ENODEV;
> }
>
> phy_dev = of_phy_connect(ndev, phy_np, &xxxx_enet_adjust_link,
> 0, pdata->phy_mode);
> if (!phy_dev) {
> netdev_err(ndev, "Could not connect to PHY\n");
> return -ENODEV;
> }
Thank you very much. I'll study this in detail.
> Do you have an ACPI table describing this hardware? What does it look
> like?
So a little background. There are several versions of this driver
floating in Qualcomm, and this is the first serious attempt to upstream
it. I'm trying to reconcile Gilad's driver with the one we use
internally for our ACPI-enabled ARM server platform (the QDF2432).
My goal is to get Gilad's driver accepted upstream with minimal changes
on my part. I will then follow up with several patches that enable ACPI
and our SOC, as well as adding missing parts like ethtool and 1588 support.
On my platform, firmware (UEFI) configures all of the GPIOs. I need to
get confirmation, but it appears that we don't actually make any GPIO
calls at all. I see code that looks like this:
for (i = 0; (!adpt->no_mdio_gpio) && i < EMAC_NUM_GPIO; i++) {
gpio_info = &adpt->gpio_info[i];
retval = of_get_named_gpio(node, gpio_info->name, 0);
if (retval < 0)
return retval;
And on our ACPI system, adpt->no_mdio_gpio is always true:
/* Assume GPIOs required for MDC/MDIO are enabled in firmware */
adpt->no_mdio_gpio = true;
--
Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora
Forum, a Linux Foundation collaborative project.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH V3] net: emac: emac gigabit ethernet controller driver
2016-04-07 21:43 ` Timur Tabi
@ 2016-04-08 0:53 ` Andrew Lunn
2016-04-08 19:06 ` Timur Tabi
0 siblings, 1 reply; 19+ messages in thread
From: Andrew Lunn @ 2016-04-08 0:53 UTC (permalink / raw)
To: Timur Tabi
Cc: Rob Herring, Gilad Avidov, netdev, linux-kernel, devicetree,
linux-arm-msm, Sagar Dharia, shankerd, Greg Kroah-Hartman,
vikrams, Christopher Covington
On Thu, Apr 07, 2016 at 04:43:47PM -0500, Timur Tabi wrote:
> On my platform, firmware (UEFI) configures all of the GPIOs. I need
> to get confirmation, but it appears that we don't actually make any
> GPIO calls at all. I see code that looks like this:
>
> for (i = 0; (!adpt->no_mdio_gpio) && i < EMAC_NUM_GPIO; i++) {
> gpio_info = &adpt->gpio_info[i];
> retval = of_get_named_gpio(node, gpio_info->name, 0);
> if (retval < 0)
> return retval;
>
> And on our ACPI system, adpt->no_mdio_gpio is always true:
>
> /* Assume GPIOs required for MDC/MDIO are enabled in firmware */
> adpt->no_mdio_gpio = true;
There are two different things here. One is configuring the pin to be
a GPIO. The second is using the GPIO as a GPIO. In this case,
bit-banging the MDIO bus.
The firmware could be doing the configuration, setting the pin as a
GPIO. However, the firmware cannot be doing the MDIO bit-banging to
make an MDIO bus available. Linux has to do that.
Or it could be we have all completely misunderstood the hardware, and
we are not doing bit-banging GPIO MDIO. There is a real MDIO
controller there, we don't use these pins as GPIOs, etc....
Andrew
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH V3] net: emac: emac gigabit ethernet controller driver
2016-04-08 0:53 ` Andrew Lunn
@ 2016-04-08 19:06 ` Timur Tabi
2016-04-08 21:07 ` Vikram Sethi
[not found] ` <5708013F.90207-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
0 siblings, 2 replies; 19+ messages in thread
From: Timur Tabi @ 2016-04-08 19:06 UTC (permalink / raw)
To: Andrew Lunn
Cc: Rob Herring, Gilad Avidov, netdev, linux-kernel, devicetree,
linux-arm-msm, Sagar Dharia, shankerd, Greg Kroah-Hartman,
vikrams, Christopher Covington
Andrew Lunn wrote:
> There are two different things here. One is configuring the pin to be
> a GPIO. The second is using the GPIO as a GPIO. In this case,
> bit-banging the MDIO bus.
>
> The firmware could be doing the configuration, setting the pin as a
> GPIO. However, the firmware cannot be doing the MDIO bit-banging to
> make an MDIO bus available. Linux has to do that.
>
> Or it could be we have all completely misunderstood the hardware, and
> we are not doing bit-banging GPIO MDIO. There is a real MDIO
> controller there, we don't use these pins as GPIOs, etc....
Actually, I think there is a misunderstanding.
On the FSM9900 SOC (which uses device-tree), the two pins that connect
to the external PHY are gpio pins. However, the driver needs to
reprogram the pinmux so that those pins are wired to the Emac
controller. That's what the the gpio code in this driver is doing: it's
just configuring the pins so that they connect directly between the Emac
and the external PHY. After that, they are no longer GPIO pins, and you
cannot use the "GPIO controlled MDIO bus". There is no MDIO controller
on the SOC. The external PHY is controlled directly from the Emac and
also from the internal PHY. It is screwy, I know, but that's what Gilad
was trying to explain.
On the QDF2432 (which uses ACPI), those two wires are now dedicated.
There are not muxed GPIOs any more -- they are hard wired between Emac
and the external PHY.
In both cases, you need to use Emac registers to communicate with the
external PHY. Stuff like link detect and link speed are configured by
programming the Emac and/or the internal phy.
And the internal phy isn't really an internal phy. It's an SGMII-like
device that's connected to the Emac and handles various phy-related
tasks. It has its own register block, but you still have to program it
in concert with the Emac. You can't really treat it separately.
So I'm beginning to believe that Gilad's driver is actually correct
as-is. There are a few minor bug fixes, but in general it's correct. I
would like to post a V4 soon that has those minor fixes.
--
Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora
Forum, a Linux Foundation collaborative project.
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH V3] net: emac: emac gigabit ethernet controller driver
2016-04-08 19:06 ` Timur Tabi
@ 2016-04-08 21:07 ` Vikram Sethi
[not found] ` <57081D96.902-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
[not found] ` <5708013F.90207-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
1 sibling, 1 reply; 19+ messages in thread
From: Vikram Sethi @ 2016-04-08 21:07 UTC (permalink / raw)
To: Timur Tabi, Andrew Lunn
Cc: Rob Herring, Gilad Avidov, netdev, linux-kernel, devicetree,
linux-arm-msm, Sagar Dharia, shankerd, Greg Kroah-Hartman,
Christopher Covington
On 04/08/2016 02:06 PM, Timur Tabi wrote:
> Andrew Lunn wrote:
>
>> There are two different things here. One is configuring the pin to be
>> a GPIO. The second is using the GPIO as a GPIO. In this case,
>> bit-banging the MDIO bus.
>>
>> The firmware could be doing the configuration, setting the pin as a
>> GPIO. However, the firmware cannot be doing the MDIO bit-banging to
>> make an MDIO bus available. Linux has to do that.
>>
>> Or it could be we have all completely misunderstood the hardware, and
>> we are not doing bit-banging GPIO MDIO. There is a real MDIO
>> controller there, we don't use these pins as GPIOs, etc....
>
> Actually, I think there is a misunderstanding.
>
> On the FSM9900 SOC (which uses device-tree), the two pins that connect to the external PHY are gpio pins. However, the driver needs to reprogram the pinmux so that those pins are wired to the Emac controller. That's what the the gpio code in this driver is doing: it's just configuring the pins so that they connect directly between the Emac and the external PHY. After that, they are no longer GPIO pins, and you cannot use the "GPIO controlled MDIO bus". There is no MDIO controller on the SOC. The external PHY is controlled directly from the Emac and also from the internal PHY. It is screwy, I know, but that's what Gilad was trying to explain.
It is incorrect to say there's no MDIO controller on the SoC. The EMAC Core on the SoC itself has a MDIO controller which talks to the external PHY. The internal SGMII is not on MDIO however.
Please see the EMAC specification.
>
> On the QDF2432 (which uses ACPI), those two wires are now dedicated. There are not muxed GPIOs any more -- they are hard wired between Emac and the external PHY.
>
> In both cases, you need to use Emac registers to communicate with the external PHY. Stuff like link detect and link speed are configured by programming the Emac and/or the internal phy.
You need to use EMAC *MDIO* registers to communicate with external PHY.
>
> And the internal phy isn't really an internal phy. It's an SGMII-like device that's connected to the Emac and handles various phy-related tasks. It has its own register block, but you still have to program it in concert with the Emac. You can't really treat it separately.
>
> So I'm beginning to believe that Gilad's driver is actually correct as-is. There are a few minor bug fixes, but in general it's correct. I would like to post a V4 soon that has those minor fixes.
>
--
Vikram Sethi
Qualcomm Technologies Inc, on behalf of Qualcomm Innovation Center, Inc.
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, a Linux Foundation Collaborative Project
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH V3] net: emac: emac gigabit ethernet controller driver
[not found] ` <57081D96.902-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
@ 2016-04-08 21:45 ` Timur Tabi
0 siblings, 0 replies; 19+ messages in thread
From: Timur Tabi @ 2016-04-08 21:45 UTC (permalink / raw)
To: Vikram Sethi, Andrew Lunn
Cc: Rob Herring, Gilad Avidov, netdev,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA, linux-arm-msm, Sagar Dharia,
shankerd-sgV2jX0FEOL9JmXXK+q4OQ, Greg Kroah-Hartman,
Christopher Covington
Vikram Sethi wrote:
>> On the FSM9900 SOC (which uses device-tree), the two pins that connect to the external PHY are gpio pins. However, the driver needs to reprogram the pinmux so that those pins are wired to the Emac controller. That's what the the gpio code in this driver is doing: it's just configuring the pins so that they connect directly between the Emac and the external PHY. After that, they are no longer GPIO pins, and you cannot use the "GPIO controlled MDIO bus". There is no MDIO controller on the SOC. The external PHY is controlled directly from the Emac and also from the internal PHY. It is screwy, I know, but that's what Gilad was trying to explain.
> It is incorrect to say there's no MDIO controller on the SoC. The EMAC Core on the SoC itself has a MDIO controller which talks to the external PHY. The internal SGMII is not on MDIO however.
> Please see the EMAC specification.
Sorry, I should have said that there is no *independent* MDIO controller
(one that has its own driver). As you said, you can only talk to the
external PHY through the Emac.
--
Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora
Forum, a Linux Foundation collaborative project.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH V3] net: emac: emac gigabit ethernet controller driver
[not found] ` <5708013F.90207-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
@ 2016-04-08 22:43 ` Bjorn Andersson
2016-04-08 23:01 ` Timur Tabi
0 siblings, 1 reply; 19+ messages in thread
From: Bjorn Andersson @ 2016-04-08 22:43 UTC (permalink / raw)
To: Timur Tabi
Cc: Andrew Lunn, Rob Herring, Gilad Avidov, netdev,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA, linux-arm-msm, Sagar Dharia,
shankerd-sgV2jX0FEOL9JmXXK+q4OQ, Greg Kroah-Hartman,
vikrams-sgV2jX0FEOL9JmXXK+q4OQ, Christopher Covington
On Fri, Apr 8, 2016 at 12:06 PM, Timur Tabi <timur-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org> wrote:
> Andrew Lunn wrote:
>
>> There are two different things here. One is configuring the pin to be
>> a GPIO. The second is using the GPIO as a GPIO. In this case,
>> bit-banging the MDIO bus.
>>
>> The firmware could be doing the configuration, setting the pin as a
>> GPIO. However, the firmware cannot be doing the MDIO bit-banging to
>> make an MDIO bus available. Linux has to do that.
>>
>> Or it could be we have all completely misunderstood the hardware, and
>> we are not doing bit-banging GPIO MDIO. There is a real MDIO
>> controller there, we don't use these pins as GPIOs, etc....
>
>
> Actually, I think there is a misunderstanding.
>
> On the FSM9900 SOC (which uses device-tree), the two pins that connect to
> the external PHY are gpio pins. However, the driver needs to reprogram the
> pinmux so that those pins are wired to the Emac controller. That's what the
> the gpio code in this driver is doing: it's just configuring the pins so
> that they connect directly between the Emac and the external PHY. After
> that, they are no longer GPIO pins, and you cannot use the "GPIO controlled
> MDIO bus". There is no MDIO controller on the SOC. The external PHY is
> controlled directly from the Emac and also from the internal PHY. It is
> screwy, I know, but that's what Gilad was trying to explain.
>
It sounds like you're trying to say that the pins used can be are
muxed as GPIO or MDIO, in the TLMM.
In the downstream kernel this is often seen with the drivers calling
gpio_request() to "reserve" said pins, but all you should do is
described the desired configuration and muxing in the pinctrl node,
reference that from your driver and simply ignore the fact that those
pins could have been used as GPIO pins.
Regards,
Bjorn
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH V3] net: emac: emac gigabit ethernet controller driver
2016-04-08 22:43 ` Bjorn Andersson
@ 2016-04-08 23:01 ` Timur Tabi
2016-04-08 23:25 ` Bjorn Andersson
0 siblings, 1 reply; 19+ messages in thread
From: Timur Tabi @ 2016-04-08 23:01 UTC (permalink / raw)
To: Bjorn Andersson
Cc: Andrew Lunn, Rob Herring, Gilad Avidov, netdev, linux-kernel,
devicetree, linux-arm-msm, Sagar Dharia, shankerd,
Greg Kroah-Hartman, vikrams, Christopher Covington
Bjorn Andersson wrote:
> It sounds like you're trying to say that the pins used can be are
> muxed as GPIO or MDIO, in the TLMM.
I'm not 100% sure, but I think that's correct. If you don't want to
have normal networking, you could connect those external pins to some
GPIO device (like an LED or whatever), and then configure the pin muxing
for GPIO purposes. But if that's true, it's only true on the FSM9900.
On the QDF2432, those lines are not connected to the TLMM. They are
instead hard-wired to the Emac.
> In the downstream kernel this is often seen with the drivers calling
> gpio_request() to "reserve" said pins, but all you should do is
> described the desired configuration and muxing in the pinctrl node,
> reference that from your driver and simply ignore the fact that those
> pins could have been used as GPIO pins.
That makes sense, but I think the driver already does that.
https://patchwork.ozlabs.org/patch/561667/
Function emac_probe_resources() has a call to of_get_named_gpio(). And
then emac_mac_up() calls gpio_request(). As far as I can tell, that's it.
I'm guessing that the of_get_named_gpio() call needs to be changed
somehow, but I'm not sure how.
--
Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora
Forum, a Linux Foundation collaborative project.
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH V3] net: emac: emac gigabit ethernet controller driver
2016-04-08 23:01 ` Timur Tabi
@ 2016-04-08 23:25 ` Bjorn Andersson
0 siblings, 0 replies; 19+ messages in thread
From: Bjorn Andersson @ 2016-04-08 23:25 UTC (permalink / raw)
To: Timur Tabi
Cc: Andrew Lunn, Rob Herring, Gilad Avidov, netdev, linux-kernel,
devicetree, linux-arm-msm, Sagar Dharia, shankerd,
Greg Kroah-Hartman, vikrams, Christopher Covington
On Fri 08 Apr 16:01 PDT 2016, Timur Tabi wrote:
> Bjorn Andersson wrote:
>
> >It sounds like you're trying to say that the pins used can be are
> >muxed as GPIO or MDIO, in the TLMM.
>
> I'm not 100% sure, but I think that's correct. If you don't want to have
> normal networking, you could connect those external pins to some GPIO device
> (like an LED or whatever), and then configure the pin muxing for GPIO
> purposes. But if that's true, it's only true on the FSM9900. On the
> QDF2432, those lines are not connected to the TLMM. They are instead
> hard-wired to the Emac.
>
Then through proper use of the pinctrl framework you should configure
the FSM9900 to mux these pins appropriately and the two solutions are
equivalent.
> >In the downstream kernel this is often seen with the drivers calling
> >gpio_request() to "reserve" said pins, but all you should do is
> >described the desired configuration and muxing in the pinctrl node,
> >reference that from your driver and simply ignore the fact that those
> >pins could have been used as GPIO pins.
>
> That makes sense, but I think the driver already does that.
>
> https://patchwork.ozlabs.org/patch/561667/
>
> Function emac_probe_resources() has a call to of_get_named_gpio(). And then
> emac_mac_up() calls gpio_request(). As far as I can tell, that's it.
>
> I'm guessing that the of_get_named_gpio() call needs to be changed somehow,
> but I'm not sure how.
>
Thanks for the link.
In short those call to the gpio framework should just be removed. They
should only be there if you're using the gpiolib to control the state of
those pins, and you're not as far as I can see.
The general outline of what you should have in your dts instead is:
soc {
tlmm {
compatible = "qcom,pinctrl-xyz";
mdio_pins_a: mdio {
state {
pins = "gpio0", "gpio1";
function = "mdio";
};
};
};
emac {
compatible = "qcom,somthing-emac";
pinctrl-names = "default";
pinctrl-0 = <&mdio_pins_a>;
};
};
Regards,
Bjorn
^ permalink raw reply [flat|nested] 19+ messages in thread
end of thread, other threads:[~2016-04-08 23:25 UTC | newest]
Thread overview: 19+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2015-12-30 1:48 [PATCH V3] net: emac: emac gigabit ethernet controller driver Gilad Avidov
2015-12-30 2:31 ` kbuild test robot
[not found] ` <1451440135-25771-1-git-send-email-gavidov-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2015-12-30 4:26 ` kbuild test robot
2015-12-31 23:10 ` Rob Herring
2016-01-29 18:22 ` Timur Tabi
[not found] ` <56ABADEA.40801-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2016-01-29 20:10 ` Rob Herring
2016-01-29 20:38 ` Timur Tabi
2016-01-30 21:58 ` Rob Herring
2016-04-07 19:28 ` Timur Tabi
[not found] ` <5706B4EF.2050600-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2016-04-07 20:10 ` Andrew Lunn
[not found] ` <20160407201009.GA16136-g2DYL2Zd6BY@public.gmane.org>
2016-04-07 21:43 ` Timur Tabi
2016-04-08 0:53 ` Andrew Lunn
2016-04-08 19:06 ` Timur Tabi
2016-04-08 21:07 ` Vikram Sethi
[not found] ` <57081D96.902-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2016-04-08 21:45 ` Timur Tabi
[not found] ` <5708013F.90207-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2016-04-08 22:43 ` Bjorn Andersson
2016-04-08 23:01 ` Timur Tabi
2016-04-08 23:25 ` Bjorn Andersson
2016-01-06 0:21 ` Timur Tabi
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).